Structural Design and Simulation Analysis of a Dual-Row Pneumatic Vegetable Precision Planter

: In order to solve the problems of domestic and foreign vegetable precision metering devices that easily damage seeds and have low seeding efﬁciency and poor qualiﬁcation rate, this paper designs a one-machine for two-row pneumatic combination seeder, which is mainly composed of a pneumatic seeding mechanism and a honeycomb seeding mechanism. The mechanism and other components and theoretical analysis of the working process of the combined seed metering device clariﬁes the minimum negative pressure for adsorbing a seed during the suction stage, along with the negative pressure required for the seed-carrying stage. It also establishes the seeding speed and movement during planting with the trajectory parameter equation and uses ADAMS software to conduct virtual experiments on the inﬂuence of the number of holes, diameters, and heights of different types of honeycomb seeding disks on the success rate of seeding. Based on research on previous pneumatic seeding mechanisms, single factor tests, orthogonal tests, and high-speed photography tests of the honeycomb seeding disk of the combined seeder were carried out on the number of holes, the diameter of holes, and the height of seeding. The results of tests conducted on okra seeds showed that when the rotating speed of the pneumatic seeding disc was 18 r/min, the diameter of the pneumatic seeding disc hole was 2.4 mm, the vacuum degree was 3.5 kPa, the number of honeycomb seeding disc holes was 24, the hole diameter was 13 mm, and the seed height was 60 mm, the working performance of the combined seed meter reached the optimal level, which provides a reference for the development of a small seed vegetable precision seeder.


Introduction
With different operating principles, seeding apparatus can be mechanical or pneumatic [1].The former feeds and drops the seeds based on the mechanical structure, which can be inclined, vertical, or horizontal disc types; socket wheel type; or finger clamp type [2,3].However, mechanical structures may damage the seeds, lower their germination rate, and reduce the qualification rate of seeding, so that mechanical apparatus is not applicable for precision seeding.Pneumatic seeders can be divided into vacuum type, blowing type, pressure type, or roller type.They all rely on the structure of the seed plate and the action of the airflow to complete the process of seed collection and dropping [4,5].However, the number and diameter of seed holes are prone to seeding failure, significantly affecting the seeding performance.It is worth noting that both pneumatic and mechanical seeding apparatuses have a low qualification rate of seeding.
Research on vegetable sowing technology and equipment began earlier in foreign countries than in China, and the level of automation and intelligence is higher [6].For example, Maschio developed a multifunctional pneumatic vegetable sowing machine to improve the versatility of the sowing unit and enable the sowing of seeds with different diameters.In Japan and South Korea, small and medium-sized mechanical seeders with power support are mainly used, and their overall structure is compact and lightweight.They are mostly suitable for sowing seed pellets, such as the YAZAKI SYV-M600W vegetable sowing machine, but the small holes of the nest wheel sower are prone to clogging with dust and impurities [7].Seeders in foreign countries are expensive and the cost of sowing is high, and they have not been widely promoted and applied in China.China's research in vegetable sowing technology and equipment started relatively late.Based on the introduction and digestion of advanced foreign technology, various types of small and medium-sized vegetable sowing equipment have been developed, but the theory and technology of sowing are not mature enough, and the performance and efficiency of sowing equipment both still need to be improved [8].The DB series vegetable sowing machine produced by Deere Play Agricultural Machinery Company has good versatility but has problems with high seed breakage rate and has serious sowing leakage.Tian et al. [9] developed a rapeseed joint sowing machine to improve sowing efficiency, using a combination of positive and negative pressure sowing, with a qualified sowing rate of 90%.Wang et al. [10] developed a circumferential groove seam air suction precision sowing machine for seeding grains, with a replanting index of less than 15% and a sowing leakage index of less than 8%.
The above analysis reveals that seeding apparatus is the core component of a vegetable precision planter.Many foreign and domestic studies have analyzed precision seeding apparatuses by focusing on pneumatic or mechanical seeding alone in single-row precision seeding.However, combined seeding apparatus that can seed in two rows has rarely been looked at.Considering the advantages and disadvantages of mechanical and pneumatic seeders at home and abroad, this paper designs a pneumatic combination precision seeder for small vegetable seeds based on the analysis of the sowing mechanism.It can simultaneously sow two rows, thereby reducing operating costs and improving sowing efficiency.Therefore, precision seeders that can sow multiple rows at the same time have broad market prospects.

The Structure and Operating Principle of the Combined Seeding Apparatus
The combination seeder is mainly composed of a pneumatic seed separation mechanism and a honeycomb seed separation mechanism, while the most commonly used precision vegetable seeders mainly use pneumatic or mechanical seed separation mechanisms.The pneumatic seed separation mechanism designed in this paper mainly uses the pressure difference to adsorb the seeds on a pneumatic seed plate, while the honeycomb seed separation mechanism mainly uses the gravity of the seeds to complete the sowing operation.The combined use of the two mechanisms can achieve one-machine for two-row precision sowing, as shown in Figure 1.

Design of Critical Components 2.1.1. Pneumatic Seeding Mechanism
The pneumatic seeding mechanism consists of a left-end cover, a right-end cover, a seed storage box, a seed scraping plate, a seed stirring wheel, a fixed frame for the seed stirring wheel, a seed blocking plate, a seed dropping plate, a pneumatic seeding plate, a sealing ring, a sealing plate, and a fixing piece for the sealing plate (Figure 2).
(1) Pneumatic seeding disc The structure of the pneumatic seeding disc is illustrated in Figure 3.As demonstrated, its major parameters include the diameter of the seeding disc and the shape, diameter, number, and position of the holes.The diameter of the seeding disc is closely related to the overall size of the seeding apparatus, the linear speed of the seeding disc, and the centripetal force required by the seed.Therefore, an equation set was established to analyze the influence of the seeding disc on seed performance.where: t-time of pneumatic seeding disc turning through the seeding area, s; l c -arc length of the seeding area, mm; v-linear speed of the pneumatic seeding disc, m/s; D-diameter of the seeding disc, mm; θ-radius of the seeding area, rad; n-rotational speed of the pneumatic seeding disc, r/min.

Pneumatic Seeding Mechanism
The pneumatic seeding mechanism consists of a left-end cover, a right-end cover, a seed storage box, a seed scraping plate, a seed stirring wheel, a fixed frame for the seed stirring wheel, a seed blocking plate, a seed dropping plate, a pneumatic seeding plate, a sealing ring, a sealing plate, and a fixing piece for the sealing plate (Figure 2).

Pneumatic Seeding Mechanism
The pneumatic seeding mechanism consists of a left-end cover, a right-end cover, a seed storage box, a seed scraping plate, a seed stirring wheel, a fixed frame for the seed stirring wheel, a seed blocking plate, a seed dropping plate, a pneumatic seeding plate, a sealing ring, a sealing plate, and a fixing piece for the sealing plate (Figure 2).(1) Pneumatic seeding disc The structure of the pneumatic seeding disc is illustrated in Figure 3.As demonstrated, its major parameters include the diameter of the seeding disc and the shape, di- ameter, number, and position of the holes.The diameter of the seeding disc is cl lated to the overall size of the seeding apparatus, the linear speed of the seeding d the centripetal force required by the seed.Therefore, an equation set was establ analyze the influence of the seeding disc on seed performance.
where: t-time of pneumatic seeding disc turning through the seeding area, s length of the seeding area, mm; v-linear speed of the pneumatic seeding disc, m diameter of the seeding disc, mm; θ-radius of the seeding area, rad; n-rotation of the pneumatic seeding disc, r/min.
The diameter of the seeding disc ranges from 140 mm to 260 mm [11].An exc large or small diameter of the pneumatic seeding disc negatively affects the perfo of the pneumatic seeding mechanism.Specifically, when the plant spacing and the ing speed are constant, an excessively small diameter speeds up the rotation of th matic seeding disc.Such condition is unfavorable for the suction of the pneumatic disc, increasing the missing rate.On the contrary, an increased diameter of the disc enables more processing holes, which slows down the pneumatic seeding creases the seed suction rate, and reduces the missing rate [12].In addition, it will the negative pressure cavity and the load of the fan.In this paper, the diamete pneumatic seeding disc is designed as 220 mm.The position of the holes should from the center of the pneumatic seeding disc maximally, because a closer posi lead to excessive vegetable seeds remaining.In this paper, the diameter of the circ the holes are located is designed as 188 mm, and the thickness of the pneumatic disc is 1 mm.In the center, there is a regular hexagon with a side length of 16 mm cooperates with the regular hexagon on the transmission shaft of the pneumatic mechanism to drive the rotation of the seeding disc.
The holes of the pneumatic seeding disc and the diameter of the seed sucti are designed based on the average width of the seed according to the Agricultu chinery Manual [13]: The diameter of the seeding disc ranges from 140 mm to 260 mm [11].An excessively large or small diameter of the pneumatic seeding disc negatively affects the performance of the pneumatic seeding mechanism.Specifically, when the plant spacing and the marching speed are constant, an excessively small diameter speeds up the rotation of the pneumatic seeding disc.Such condition is unfavorable for the suction of the pneumatic seeding disc, increasing the missing rate.On the contrary, an increased diameter of the seeding disc enables more processing holes, which slows down the pneumatic seeding disc, increases the seed suction rate, and reduces the missing rate [12].In addition, it will increase the negative pressure cavity and the load of the fan.In this paper, the diameter of the pneumatic seeding disc is designed as 220 mm.The position of the holes should be away from the center of the pneumatic seeding disc maximally, because a closer position will lead to excessive vegetable seeds remaining.In this paper, the diameter of the circle where the holes are located is designed as 188 mm, and the thickness of the pneumatic seeding disc is 1 mm.In the center, there is a regular hexagon with a side length of 16 mm, which cooperates with the regular hexagon on the transmission shaft of the pneumatic seeding mechanism to drive the rotation of the seeding disc.
The holes of the pneumatic seeding disc and the diameter of the seed suction holes are designed based on the average width of the seed according to the Agricultural Machinery Manual [13]: where: d-diameter of suction hole, mm; b-average width of seed, mm.The seed rower designed in this paper mainly sows spherical-like seeds with an average width between 3.5 mm and 4.3 mm, so the diameter of this type of hole is 2.2~2.8mm.

Honeycomb Seeding Mechanism
(1) Honeycomb seeding disc The structure of the honeycomb seeding disc is shown in Figure 4.It is key to achieving the seeding in two rows.Its main body is a cylinder, with cylindrical holes of the same diameter punched at a certain angle from the two bottom surfaces of the cylinder.An excessively large diameter of seeding disc may result in missed seeding under the centrifugal force.Currently, the available diameter is generally 140-260 mm.The motion trajectory of seeds dropping from the pneumatic seeding mechanism is influenced by external factors, including wind force and mechanical vibration.Thus, holes with a large diameter increase the difficulty for the seed to drop into.Therefore, in this paper, based on the above analysis, the diameter of the holes for the honeycomb seeding disc is designed as 150 mm.
cessively large diameter of seeding disc may result in missed seeding under the cent gal force.Currently, the available diameter is generally 140-260 mm.The motion tr tory of seeds dropping from the pneumatic seeding mechanism is influenced by exte factors, including wind force and mechanical vibration.Thus, holes with a large diam increase the difficulty for the seed to drop into.Therefore, in this paper, based on the a analysis, the diameter of the holes for the honeycomb seeding disc is designed as 150 (2) Seed sorting bin Based on the diameter of the honeycomb seeding disc, the maximum diameter width of the seed sorting bin are set to 200 mm and 22.5 mm, respectively.There quarter ring in the seed sorting bin, and the difference in the radii of the ring is equ the diameter of the hole.A quarter of the circle is placed in the first half of the honeyc seeding disc, as shown in Figure 5.The seed sorting bin is fixed and does not rotate the rotation of the honeycomb seeding disc, during which the seeds continuously into the seeding cavity through the connection of the inclined holes and the quarter r  (2) Seed sorting bin Based on the diameter of the honeycomb seeding disc, the maximum diameter and width of the seed sorting bin are set to 200 mm and 22.5 mm, respectively.There is a quarter ring in the seed sorting bin, and the difference in the radii of the ring is equal to the diameter of the hole.A quarter of the circle is placed in the first half of the honeycomb seeding disc, as shown in Figure 5.The seed sorting bin is fixed and does not rotate with the rotation of the honeycomb seeding disc, during which the seeds continuously drop into the seeding cavity through the connection of the inclined holes and the quarter ring.
tory of seeds dropping from the pneumatic seeding mechanism is influenced by e factors, including wind force and mechanical vibration.Thus, holes with a large d increase the difficulty for the seed to drop into.Therefore, in this paper, based on th analysis, the diameter of the holes for the honeycomb seeding disc is designed as 1 (2) Seed sorting bin Based on the diameter of the honeycomb seeding disc, the maximum diame width of the seed sorting bin are set to 200 mm and 22.5 mm, respectively.Th quarter ring in the seed sorting bin, and the difference in the radii of the ring is e the diameter of the hole.A quarter of the circle is placed in the first half of the hon seeding disc, as shown in Figure 5.The seed sorting bin is fixed and does not rota the rotation of the honeycomb seeding disc, during which the seeds continuous into the seeding cavity through the connection of the inclined holes and the quart

Operating Principle
During the operation, a plastic hose is connected to the negative-pressure air inlet of the pneumatic seeding mechanism and the high-pressure vortex fan.The negative-pressure air inlet is connected to the negative-pressure cavity of the right end cover, with sealing rings between them to reduce the missing air.When the seeds are delivered to the seeding area, the negative pressure disappears instantly so that the seeds drop into the inoculation hopper and then pass through the holes under the action of gravity.The holes of the honeycomb seeding disc are connected to the seed sorting bin with a trencher below.In this combined way, the seeding operation is completed.There is a distance between the two rows of seeds, so they are arranged alternately.

Seeding
Under the effects of negative pressure, the seeds are sucked iton the holes of the pneumatic seeding disc and rotate to the seeding area.They then fall into the inoculation hopper and the holes of the honeycomb seeding mechanism, and then pass through the seed sorting bin.In this paper, a seed is regarded as a particle, and the point where the seed leaves the feeding hole is set as the origin.Meanwhile, the marching direction of the planter is undertaken as the positive X-axis direction, and the vertically downward direction is the positive Y-axis direction [14].The honeycomb and the pneumatic seeding mechanisms are installed on the planter without relative movement, so they are stationary relative to the planter.Thus, influence from the speed of the planter is not considered herein.Furthermore, the air resistance can be ignored because there is a plastic shell coverage when the seeds drop into the honeycomb seeding mechanism.The seed dropping trajectory is shown in Figure 6.
Under the effects of negative pressure, the seeds are sucked iton the holes of the pneumatic seeding disc and rotate to the seeding area.They then fall into the inoculation hopper and the holes of the honeycomb seeding mechanism, and then pass through the seed sorting bin.In this paper, a seed is regarded as a particle, and the point where the seed leaves the feeding hole is set as the origin.Meanwhile, the marching direction of the planter is undertaken as the positive X-axis direction, and the vertically downward direction is the positive Y-axis direction [14].The honeycomb and the pneumatic seeding mechanisms are installed on the planter without relative movement, so they are stationary relative to the planter.Thus, influence from the speed of the planter is not considered herein.Furthermore, the air resistance can be ignored because there is a plastic shell coverage when the seeds drop into the honeycomb seeding mechanism.The seed dropping trajectory is shown in Figure 6.When the seed leaves the seeding area, the velocities in the X and Y directions are as follows: The resultant velocity of the seed in contacting with the honeycomb seeding disc is expressed as follows: When the seed leaves the seeding area, the velocities in the X and Y directions are as follows: The resultant velocity of the seed in contacting with the honeycomb seeding disc is expressed as follows: where: n-rotational speed of the pneumatic seed disc, r/min; D 2 -diameter of the index circle where the seed disc hole is located, mm; g-acceleration of gravity, m/s 2 ; γ-angle of the seed with the vertical direction when it is first thrown, rad; t-time of seed drop, s; Vx-seed velocity in x-direction when leaving the seed drop, m/s; Vy-seed velocity in y-direction when leaving the seed drop, m/s; V x-the partial velocity in the x-direction when the seed touches the honeycomb seed tray, m/s; V y-the partial velocity in the y-direction when the seed touches the honeycomb seed tray, m/s.Hopping speed when seeds touch the honeycomb seed discharge tray: The angle between the resultant velocity and the vertical direction when the seeds contacts with the honeycomb seeding disc is given as follows: The below expression shows the motion trajectory of the seed when it leaves the pneumatic seeding mechanism and contacts with the honeycomb seeding disc: where: V-the combined velocity of the seeds when contacting the honeycomb seeding disc, m/s; δ-the angle between the combined velocity and the vertical direction when the seeds are in contact with the honeycomb seeding disc, • ; S x -the displacement from the seeds leaving the pneumatic seeding mechanism to contacting the honeycomb seeding disc in the x direction, m; S y -displacement from the seed leaving the pneumatic seed releasing mechanism to the contacting honeycomb seed releasing disc in the y direction, m.When contacting with the honeycomb seeding disc, the seeds will collide and bounce, which greatly lowers the success rate of precision seeding.The speed of the seed when contacting the honeycomb seeding disc is affected by the rotational speed of the pneumatic seeding disc and the distance between the honeycomb and the pneumatic seeding mechanisms.The faster the rotation of the pneumatic seeding disc, the greater the initial velocity of the seed when it leaves the pneumatic seeding mechanism.The larger the installation distance between the pneumatic and honeycomb seeding mechanisms, the faster the seed falls under gravity.These two factors increase the chances of seeds contacting the honeycomb seeding apparatus.Therefore, it is recommended to minimize the rotating speed of the pneumatic seeding mechanism and the distance between it and the honeycomb seeding mechanism if possible.
The time of seed dropping can be calculated based on the partial velocities in the x-axis and y-axis directions and the distance between the pneumatic and honeycomb seeding mechanisms.Thus, the falling trajectory of the seeds can be calculated with the trajectory equation, based on which the relative installation position between the pneumatic and honeycomb seeding mechanisms can be determined.

Seed Dropping
After dropping from the feeding hole of the pneumatic seeding mechanism, the seed will pass through the inoculation hopper of the honeycomb seeding mechanism and drop into the holes of the honeycomb seeding disc.To help the seed drop smoothly, the seed dropping is analyzed theoretically, and the optimal inclination angle of the holes is calculated.The force analysis is demonstrated in Figure 7.The static and dynamic friction coefficients between particles and the wall are 0.43 and 0.03, respectively, and the recovery coefficient between them is 0.56 [15].
where: u-friction factor between seed and honeycomb seeding disc; θ-slanting angle of honeycomb seeding disc hole, • ; N 2 -supporting force of seed by slanting cylindrical hole, N; G-gravity of seed itself, N; J 2 -seed centrifugal force in honeycomb seeding disc, N; f 2 -frictional force of seed in the hole, N; Note: J 2 is always the reverse of the radial direction of the honeycomb seed tray.By calculating the angle of inclination of the type hole to 2 • , the seeds can fall from the type hole of the honeycomb seed tray.lated.The force analysis is demonstrated in Figure 7.The static and dynamic fric efficients between particles and the wall are 0.43 and 0.03, respectively, and the r coefficient between them is 0.56 [15].( ) where: u-friction factor between seed and honeycomb seeding disc; θ-slanting honeycomb seeding disc hole, °; N2-supporting force of seed by slanting cylindri N; G-gravity of seed itself, N; J2-seed centrifugal force in honeycomb seeding f2-frictional force of seed in the hole, N; Note: J2 is always the reverse of the radi tion of the honeycomb seed tray.By calculating the angle of inclination of the typ 2°, the seeds can fall from the type hole of the honeycomb seed tray.

Automatic Dynamic Analysis of Mechanical Systems (ADAMS) Virtual Experimen
For the pneumatic seeding mechanism, the experiment simulates the seeds b sorbed on the seeding disc, so the stirring wheel, black washer, seed blocking pl seed scraping plate can be removed.That is, only the front cover, rear cover, seed and seeding plate are kept [16,17].The main part of the honeycomb seeding me is retained and a driving pair is equipped.The simplified pneumatic and hon seeding mechanisms are introduced into ADAMS [18,19].After the three-dim (3D) model of the combined seeding apparatus is imported into ADAMS, the properties of the honeycomb seeding apparatus are set.After that, the system w matically calculate the centroid position and rotational inertia of each component ing dynamics.Each component is renamed for easier identification [20].After the a of constraints to each component, drivers were supplemented for the pneumatic a eycomb seeding discs.In this case, the rotating speeds of these two discs are sub proportional relationship.

Bench Experiments
To obtain the optimal parameter combination of the combined seeding ap performance tests were conducted on the speed of the pneumatic seeding disc, th eter of the holes, and the vacuum degree of the air cavity of the pneumatic seedin anism in the early stage.In addition, single factor and orthogonal experiments w formed on the number and diameter of holes and the seeding height of the hon

Automatic Dynamic Analysis of Mechanical Systems (ADAMS) Virtual Experiment
For the pneumatic seeding mechanism, the experiment simulates the seeds being adsorbed on the seeding disc, so the stirring wheel, black washer, seed blocking plate, and seed scraping plate can be removed.That is, only the front cover, rear cover, seeding disc, and seeding plate are kept [16,17].The main part of the honeycomb seeding mechanism is retained and a driving pair is equipped.The simplified pneumatic and honeycomb seeding mechanisms are introduced into ADAMS [18,19].After the three-dimensional (3D) model of the combined seeding apparatus is imported into ADAMS, the material properties of the honeycomb seeding apparatus are set.After that, the system will automatically calculate the centroid position and rotational inertia of each component for solving dynamics.Each component is renamed for easier identification [20].After the addition of constraints to each component, drivers were supplemented for the pneumatic and honeycomb seeding discs.In this case, the rotating speeds of these two discs are subject to a proportional relationship.

Bench Experiments
To obtain the optimal parameter combination of the combined seeding apparatus, performance tests were conducted on the speed of the pneumatic seeding disc, the diameter of the holes, and the vacuum degree of the air cavity of the pneumatic seeding mechanism in the early stage.In addition, single factor and orthogonal experiments were performed on the number and diameter of holes and the seeding height of the honeycomb seeding disc.
In this paper, okra seeds were selected as experimental materials.To achieve better experimental results, the okra seeds were screened based on a purity of ≥95% and moisture of ≤8%.
The testing instruments include the combined seeding apparatus, a negative-pressure fan, a speed tester, a high-precision digital pressure gauge, a U-shaped pressure gauge, glass glue, a hose, a servo motor (130ST-M10015), a high-speed camera (FASTCAM MiNi WX50 type675KM-16, HOTON, Tokyo, Japan), lighting devices, and a control cabinet.In this paper, for the high-speed camera, the maximum recording speed is 67,500 frames per second (FPS), the recording capacity is 16 G, and the recording speed is 125 FPS.The testing instruments are shown in Figure 8.
sure fan, a speed tester, a high-precision digital pressure gauge, a U-shaped p gauge, glass glue, a hose, a servo motor (130ST-M10015), a high-speed camera (FA MiNi WX50 type675KM-16, HOTON, Tokyo, Japan), lighting devices, and a cont net.In this paper, for the high-speed camera, the maximum recording speed i frames per second (FPS), the recording capacity is 16 G, and the recording spee FPS.The testing instruments are shown in Figure 8.

Test Indicators and Methods
Based on the GB/T6973-2005 "Test Methods for Single Grain (Precision) Plant successful seeding rate, missed seeding rate, and re-seeding rate were determine ify the performance of the precision seeding apparatus [21,22].
The formula for calculating the indicator is as follows: where: U-seed casting pass rate, %; m1-number of qualified seeds in the exp M′-total number of samples.
where: V-missed cast rate, %; m2-number of missed seeds in the test.
where: W-re-casting rate; m3-number of reabsorbed seeds in the experiment.

Single Factor Experiments
The test reveals that the pneumatic seeding mechanism performs best w speed is 18 r/min, the vacuum degree of the air chamber is 3.5 kPa, and the diam the holes is 2.4 mm.When the pneumatic seeding mechanism operates at the optim

Test Indicators and Methods
Based on the GB/T6973-2005 "Test Methods for Single Grain (Precision) Planters", the successful seeding rate, missed seeding rate, and re-seeding rate were determined to verify the performance of the precision seeding apparatus [21,22].
The formula for calculating the indicator is as follows: where: U-seed casting pass rate, %; m 1 -number of qualified seeds in the experiment; M -total number of samples.
where: V-missed cast rate, %; m 2 -number of missed seeds in the test.
where: W-re-casting rate; m 3 -number of reabsorbed seeds in the experiment.

Single Factor Experiments
The test reveals that the pneumatic seeding mechanism performs best when the speed is 18 r/min, the vacuum degree of the air chamber is 3.5 kPa, and the diameter of the holes is 2.4 mm.When the pneumatic seeding mechanism operates at the optimal level, it is combined with the honeycomb seeding mechanism.To determine the optimal operating state of the combined seeding apparatus for precision seeding in two rows, a single factor experiment was conducted with a honeycomb seeding apparatus.During the experiment, the numbers of holes were 12, 18, and 24; the diameters of the holes were 11 mm and 13 mm; and the seeding heights were 60 mm, 80 mm, and 100 mm.After the test bench ran stably, 300 seeds were experimented on, and the experiment was repeated 10 times at each level, based on which the average value was calculated.

Orthogonal Experiments
The results of the single factor experiment revealed that the number of holes, the diameter of the holes, and the seeding height of the honeycomb seeding apparatus exert crucial effects on the operating performance of the combined seeding apparatus.Thus, they were subjected to orthogonal experiments to determine their influencing order that affects the operating parameters of the experimental indicators and to obtain the optimal operating parameter combination for the combined seeding apparatus.It aims to give a theoretical basis for the optimal running of the combined seeding apparatus [23].The levels of orthogonal experimental factors are shown in Table 1.Three hundred seeds were experimented on, and the experiment was repeated 10 times at each level, based on which the average value was calculated.

Double-Row Experiments
After obtaining the optimal parameter combination of the combined seeding apparatus, a double-row experiment was performed on a single disc.Herein, the vertical distance between the honeycomb seeding mechanism and the conveyor belt was set as 130 mm for the experiment.In addition, the speed of the conveyor belt was 10 r/min, 20 r/min, and 30 r/min, and the plant spacing and row spacing were selected as the experimental indicators.The experiment was repeated 10 times, and the average value was calculated and recorded.

High-Speed Photography Experiments
The purpose of the high-speed photography experiment is to observe the condition of the seeds throughout the seeding.Due to the fast rotation of the apparatus, the suction and seeding of seeds by the holes are difficult to observe.In this paper, a high-speed camera was adopted to photograph the seeding process and observe the motion of the seeds in the connection section between the pneumatic and honeycomb seeding mechanisms [24][25][26][27][28].

Virtual Experiment of Seed Dropping Trajectory
The seed dropping trajectory is demonstrated in Figure 9.In the pneumatic seeding mechanism, the seeds drop in sequence with the rotation of the seeding disc, and they accurately drop into the holes in the honeycomb seeding disc that continuously rotates.The holes in the honeycomb seeding disc correspond to those in the pneumatic seeding disc, and no missed feeding occurred.

Virtual Experiments with Different Numbers of Holes
As long as a pneumatic seeding mechanism is designed, the number of holes on the pneumatic seeding disc is fixed.Therefore, an excessively small number of holes on the honeycomb seeding disc will cause missed feeding at a constant speed of the pneumatic seeding mechanism.An excessively large number of holes may cause seeds to drop into adjacent holes, resulting in re-seeding.Therefore, the number of holes in the honeycomb seeding disc importantly affects the seeding success rate.Based on the preliminary experimental results, the speed of the pneumatic seeding mechanism was set to 18 r/min, and the number of holes in the honeycomb seeding disc was 12, 18, and 24.The simulation results show that all 24 seeds dropped into the holes, but 7, 5, and 4 seeds bounced out when the number of holes was 12, 18, and 24, respectively.Thus, the corresponding seeding success rates are 70.1%,79.2%, and 83.3%.The results indicate that as the number of seeds increases, the seeding success rate increases, with the highest value achieved when there are 24 holes.Therefore, the optimal number of holes in the honeycomb seeding disc is determined as 24.
Processes 2023, 11, x FOR PEER REVIEW 11 of 18 The holes in the honeycomb seeding disc correspond to those in the pneumatic seeding disc, and no missed feeding occurred.

Virtual Experiments with Different Numbers of Holes
As long as a pneumatic seeding mechanism is designed, the number of holes on the pneumatic seeding disc is fixed.Therefore, an excessively small number of holes on the honeycomb seeding disc will cause missed feeding at a constant speed of the pneumatic seeding mechanism.An excessively large number of holes may cause seeds to drop into adjacent holes, resulting in re-seeding.Therefore, the number of holes in the honeycomb seeding disc importantly affects the seeding success rate.Based on the preliminary experimental results, the speed of the pneumatic seeding mechanism was set to 18 r/min, and the number of holes in the honeycomb seeding disc was 12, 18, and 24.The simulation results show that all 24 seeds dropped into the holes, but 7, 5, and 4 seeds bounced out when the number of holes was 12, 18, and 24, respectively.Thus, the corresponding seeding success rates are 70.1%,79.2%, and 83.3%.The results indicate that as the number of seeds increases, the seeding success rate increases, with the highest value achieved when there are 24 holes.Therefore, the optimal number of holes in the honeycomb seeding disc is determined as 24.

Virtual Experiments with Different Diameters of Holes
As mentioned above, the diameter of holes in the honeycomb seeding disc significantly affects the seeding success rate.On the one hand, an excessively small diameter of holes will increase the difficulty for seeds to drop into the holes, reducing the seeding success rate.On the other hand, as the diameter of the hole increases, spacing among the holes decreases, which can easily cause multiple seeds to drop into the same hole.Therefore, virtual experiments were performed on different hole diameters (11 mm, 13 mm, and 15 mm) to determine the optimal diameter.The simulation results showed that all 24 seeds dropped into the holes, but 5, 4, and 4 seeds bounced out at hole diameters of 11, 13, and 15 mm, respectively.Thus, the corresponding seeding success rates were 79.1%, 83.3%, and 83.3%, respectively.The seeding success rate increases with the increased diameter of holes but is the same at the diameter of 13 and 15 mm.Therefore, the diameter of the hole was determined in subsequent bench tests.

Virtual Experiments at Different Seeding Heights
The installation distance between the pneumatic and honeycomb seeding mechanisms is another key factor that affects the seeding success rate.An excessively large distance between the pneumatic and honeycomb seeding mechanisms is not conductive to the seeds dropping into the holes in the honeycomb seeding disc, while a too small distance is not beneficial for installing the mechanisms.Therefore, simulation experiments were conducted using a honeycomb seeding disc with 24 holes, a rotating speed of 18

Virtual Experiments with Different Diameters of Holes
As mentioned above, the diameter of holes in the honeycomb seeding disc significantly affects the seeding success rate.On the one hand, an excessively small diameter of holes will increase the difficulty for seeds to drop into the holes, reducing the seeding success rate.On the other hand, as the diameter of the hole increases, spacing among the holes decreases, which can easily cause multiple seeds to drop into the same hole.Therefore, virtual experiments were performed on different hole diameters (11 mm, 13 mm, and 15 mm) to determine the optimal diameter.The simulation results showed that all 24 seeds dropped into the holes, but 5, 4, and 4 seeds bounced out at hole diameters of 11, 13, and 15 mm, respectively.Thus, the corresponding seeding success rates were 79.1%, 83.3%, and 83.3%, respectively.The seeding success rate increases with the increased diameter of holes but is the same at the diameter of 13 and 15 mm.Therefore, the diameter of the hole was determined in subsequent bench tests.

Virtual Experiments at Different Seeding Heights
The installation distance between the pneumatic and honeycomb seeding mechanisms is another key factor that affects the seeding success rate.An excessively large distance between the pneumatic and honeycomb seeding mechanisms is not conductive to the seeds dropping into the holes in the honeycomb seeding disc, while a too small distance is not beneficial for installing the mechanisms.Therefore, simulation experiments were conducted using a honeycomb seeding disc with 24 holes, a rotating speed of 18 r/min, and installation distances of 60 mm, 80 mm, and 100 mm.The results indicate that the seeding success rate is the same (83.3%)for the three different installation distances.Under ideal conditions, a small height difference exerts a slight impact on the qualification rate of seeding.However, the actual seeding results may be affected by several uncontrollable factors, such as wind.Therefore, the distance between the two seeding mechanisms should be minimized as much as possible to minimize the influence on seeding.In this paper, it is selected as 60 mm.

Single Factor Experiments (1) The Effect of the Number of Holes in Honeycomb Seeding Discs on Seeding
The experimental results in Figure 10 reveal that the seeding success rate increases with the increasing number of holes in the honeycomb seeding disc, while the missed seeding and re-seeding rates are reduced continuously.When the number of holes is 24, the seeding success rate is 82.58%, the missed seeding rate is 8.21%, and the re-seeding rate is 9.21%.These results suggest that the combined seeding apparatus is in the optimal performance state.
The experimental results in Figure 10 reveal that the seeding success rate increases with the increasing number of holes in the honeycomb seeding disc, while the missed seeding and re-seeding rates are reduced continuously.When the number of holes is 24, the seeding success rate is 82.58%, the missed seeding rate is 8.21%, and the re-seeding rate is 9.21%.These results suggest that the combined seeding apparatus is in the optimal performance state.The experimental results in Figure 11 disclose that the seeding success rate increases with the enlarged diameter of the holes in the honeycomb seeding disc.When the diameter of hole is 15 mm, the seeding success rate is the highest (82.58%), and the re-seeding rate (9.21%) and missed seeding rate (8.21%) are the lowest.The analysis indicates that the increased diameter of holes in the honeycomb seeding disc enlarges the range of seeding, which is beneficial for improving the seeding success rate.(3) The Impact of Seeding Height on Seeding (2) The Influence of the Diameter of Holes in Honeycomb Seed Discs on Seeding The experimental results in Figure 11 disclose that the seeding success rate increases with the enlarged diameter of the holes in the honeycomb seeding disc.When the diameter of hole is 15 mm, the seeding success rate is the highest (82.58%), and the re-seeding rate (9.21%) and missed seeding rate (8.21%) are the lowest.The analysis indicates that the increased diameter of holes in the honeycomb seeding disc enlarges the range of seeding, which is beneficial for improving the seeding success rate.
The experimental results in Figure 10 reveal that the seeding success rate increases with the increasing number of holes in the honeycomb seeding disc, while the missed seeding and re-seeding rates are reduced continuously.When the number of holes is 24, the seeding success rate is 82.58%, the missed seeding rate is 8.21%, and the re-seeding rate is 9.21%.These results suggest that the combined seeding apparatus is in the optimal performance state.The experimental results in Figure 11 disclose that the seeding success rate increases with the enlarged diameter of the holes in the honeycomb seeding disc.When the diameter of hole is 15 mm, the seeding success rate is the highest (82.58%), and the re-seeding rate (9.21%) and missed seeding rate (8.21%) are the lowest.The analysis indicates that the increased diameter of holes in the honeycomb seeding disc enlarges the range of seeding, which is beneficial for improving the seeding success rate.(3) The Impact of Seeding Height on Seeding (

3) The Impact of Seeding Height on Seeding
As demonstrated in Figure 12, the seeding success rate decreases with the elevating seeding height.When the seeding height is 60 mm, the seeding success rate is 82.58%, is the highest.When the seeding height is 100 mm, the minimum qualification rate for seeding is 80.56% and the minimum missed seeding rate is 7.36%.Therefore, with the continuously increased seeding height, the seeding qualification rate decreases insignificantly.A comprehensive balance analysis of the above results demonstrates that when the seeding height is 60 mm, the seeding success rate is the highest (82.58%), the missed seeding rate is 8.21%, and the re-seeding rate is 9.21%.As demonstrated in Figure 12, the seeding success rate decreases with the elevating seeding height.When the seeding height is 60 mm, the seeding success rate is 82.58%, which is the highest.When the seeding height is 100 mm, the minimum qualification rate for seeding is 80.56% and the minimum missed seeding rate is 7.36%.Therefore, with the continuously increased seeding height, the seeding qualification rate decreases insignificantly.A comprehensive balance analysis of the above results demonstrates that when the seeding height is 60 mm, the seeding success rate is the highest (82.58%), the missed seeding rate is 8.21%, and the re-seeding rate is 9.21%.

Orthogonal Experiments
(1) The orthogonal experimental scheme and results are listed in Table 2.

Orthogonal Experiments
(1) The orthogonal experimental scheme and results are listed in Table 2. (2) Results and Analysis Table 3 shows the range analysis data of the seeding success rate.As shown, A3, B3, and C1 are the optimal levels of factors A, B, and C at k D3 > k D2 > k D1 , k E3 > k E2 > k E1 , and kF1 > kF3 > kF2, respectively.The higher the qualification rate of seeding, the better the operating performance of the combined seeding apparatus.Therefore, the optimal level for seeding success rate is A3B3C1 and 16.88 > 1.78 > 1.17.The results indicated that the number of holes exerts the greatest effect on the successful seeding, followed by the diameter of holes and the seeding height in turn.Analysis of the range of missed seeding rates reveal that A3, B2, and C2 are the optimal levels of factors A, B, and C at k D1 > k D2 > k D3 , k E3 > k E1 > k E2 , and k F3 > k F1 > k F2 , respectively.The lower the missing rate, the better the operating performance of the combined seeding apparatus.Therefore, the optimal combination for the missed seeding rate is A3B2C2, with 8.27 > 0.50 > 0.49.This indicates that the number of holes exhibits the greatest impact on the missed seeding rate, followed by the seeding height and the diameter of holes in turn.In addition, analysis on the range of re-seeding rates suggests that A3, B3, and C1 are the optimal levels of factors A, B, and C at k D1 > k D2 > k D3 , k E1 > k E2 > k E3 , and k F2 > k F3 > k F1 , respectively.Similarly, the lower the seeding rate, the better the operating performance of the combined seeding apparatus.Thus, the optimal combination for a successful seeding rate is A3B3C1, with 8.61 > 2.23 > 1.21.This means that the number of holes has the greatest impact on the re-seeding rate, followed by the diameter of holes and the seeding height in turn.
Table 4 displays the variance of results of the orthogonal experiments.According to the table, F0.1 (2, 6) = 3.46 is obtained.Comparison between it and the F-value in Table 4 demonstrates that all the above three factors can affect the seeding success rate, of which the number of holes in the honeycomb seeding disc exhibits the most significant impact, while the diameter of holes and seeding height show slight impacts.Furthermore, it is observed that all these three indicators affect the missed seeding rate and the re-seeding rate, with the number of holes exerting the greatest effects.Similarly, the lower the seeding rate, the better the operatin bined seeding apparatus.Thus, the optimal combination for a A3B3C1, with 8.61 > 2.23 > 1.21.This means that the numbe impact on the re-seeding rate, followed by the diameter of hole turn.
Table 4 displays the variance of results of the orthogonal the table, F0.1 (2, 6) = 3.46 is obtained.Comparison between it demonstrates that all the above three factors can affect the see the number of holes in the honeycomb seeding disc exhibits th while the diameter of holes and seeding height show slight i observed that all these three indicators affect the missed seedi rate, with the number of holes exerting the greatest effects.Similarly, the lower the seeding rate, the better the operating performance of the combined seeding apparatus.Thus, the optimal combination for a successful seeding rate is A3B3C1, with 8.61 > 2.23 > 1.21.This means that the number of holes has the greatest impact on the re-seeding rate, followed by the diameter of holes and the seeding height in turn.
Table 4 displays the variance of results of the orthogonal experiments.According to the table, F 0.1 (2, 6) = 3.46 is obtained.Comparison between it and the F-value in Table 4 demonstrates that all the above three factors can affect the seeding success rate, of which the number of holes in the honeycomb seeding disc exhibits the most significant impact, while the diameter of holes and seeding height show slight impacts.Furthermore, it is observed that all these three indicators affect the missed seeding rate and the re-seeding rate, with the number of holes exerting the greatest effects.Similarly, the lower the seeding rate, the better the operating performance of the combined seeding apparatus.Thus, the optimal combination for a successful seeding rate is A3B3C1, with 8.61 > 2.23 > 1.21.This means that the number of holes has the greatest impact on the re-seeding rate, followed by the diameter of holes and the seeding height in turn.
Table 4 displays the variance of results of the orthogonal experiments.According to the table, F0.1 (2, 6) = 3.46 is obtained.Comparison between it and the F-value in Table 4 demonstrates that all the above three factors can affect the seeding success rate, of which the number of holes in the honeycomb seeding disc exhibits the most significant impact, while the diameter of holes and seeding height show slight impacts.Furthermore, it is observed that all these three indicators affect the missed seeding rate and the re-seeding rate, with the number of holes exerting the greatest effects.The experimental indicators are required to achieve a higher seeding success rate while minimizing the missed seeding and re-seeding rates maximally.Based on a joint analysis of Tables 3 and 4, the optimal combination is determined as A3B2C1, with a seeding success rate of 81.63%, a missed seeding rate of 8.63%, and a re-seeding rate of 9.74%.

High-Speed Photography Experiments
Figure 13 illustrates the results of the high-speed photography experiments for the combined seeding apparatus.The figure demonstrates that re-seeding and missed seeding are both observed during the seeding.The missed seeding is attributed to two aspects.On the one hand, the matching between the rotating speed parameters of the pneumatic and honeycomb seeding mechanisms results in a deviation of the seeds accurately dropping into the honeycomb seeding mechanism.On the other hand, the seeds do not drop into the hole in the honeycomb seeding mechanism exactly or even drop out of the mechanism.Meanwhile, two major reasons are summarized for re-seeding.One is that the seeds are stacked in the seed storage box of the pneumatic seeding mechanism and are subjected to compression and friction.In this case, multiple seeds may be sucked by the pneumatic seeding mechanism and then dropped into the honeycomb seeding mechanism.The other is that the seeds may fall on the edge of holes in the honeycomb seeding mechanism and then drop into the adjacent holes.Similarly, the lower the seeding rate, the better the operating performance of the combined seeding apparatus.Thus, the optimal combination for a successful seeding rate is A3B3C1, with 8.61 > 2.23 > 1.21.This means that the number of holes has the greatest impact on the re-seeding rate, followed by the diameter of holes and the seeding height in turn.
Table 4 displays the variance of results of the orthogonal experiments.According to the table, F0.1 (2, 6) = 3.46 is obtained.Comparison between it and the F-value in Table 4 demonstrates that all the above three factors can affect the seeding success rate, of which the number of holes in the honeycomb seeding disc exhibits the most significant impact, while the diameter of holes and seeding height show slight impacts.Furthermore, it is observed that all these three indicators affect the missed seeding rate and the re-seeding rate, with the number of holes exerting the greatest effects.The experimental indicators are required to achieve a higher seeding success rate while minimizing the missed seeding and re-seeding rates maximally.Based on a joint analysis of Tables 3 and 4, the optimal combination is determined as A3B2C1, with a seeding success rate of 81.63%, a missed seeding rate of 8.63%, and a re-seeding rate of 9.74%.

High-Speed Photography Experiments
Figure 13 illustrates the results of the high-speed photography experiments for the combined seeding apparatus.The figure demonstrates that re-seeding and missed seeding are both observed during the seeding.The missed seeding is attributed to two aspects.On the one hand, the matching between the rotating speed parameters of the pneumatic and honeycomb seeding mechanisms results in a deviation of the seeds accurately dropping into the honeycomb seeding mechanism.On the other hand, the seeds do not drop into the hole in the honeycomb seeding mechanism exactly or even drop out of the mechanism.Meanwhile, two major reasons are summarized for re-seeding.One is that the seeds are stacked in the seed storage box of the pneumatic seeding mechanism and are subjected to compression and friction.In this case, multiple seeds may be sucked by the pneumatic seeding mechanism and then dropped into the honeycomb seeding mechanism.The other is that the seeds may fall on the edge of holes in the honeycomb seeding mechanism and then drop into the adjacent holes.Similarly, the lower the seeding rate, the better the operating performance of the combined seeding apparatus.Thus, the optimal combination for a successful seeding rate is A3B3C1, with 8.61 > 2.23 > 1.21.This means that the number of holes has the greatest impact on the re-seeding rate, followed by the diameter of holes and the seeding height in turn.
Table 4 displays the variance of results of the orthogonal experiments.According to the table, F0.1 (2, 6) = 3.46 is obtained.Comparison between it and the F-value in Table 4 demonstrates that all the above three factors can affect the seeding success rate, of which the number of holes in the honeycomb seeding disc exhibits the most significant impact, while the diameter of holes and seeding height show slight impacts.Furthermore, it is observed that all these three indicators affect the missed seeding rate and the re-seeding rate, with the number of holes exerting the greatest effects.The experimental indicators are required to achieve a higher seeding success rate while minimizing the missed seeding and re-seeding rates maximally.Based on a joint analysis of Tables 3 and 4, the optimal combination is determined as A3B2C1, with a seeding success rate of 81.63%, a missed seeding rate of 8.63%, and a re-seeding rate of 9.74%.

High-Speed Photography Experiments
Figure 13 illustrates the results of the high-speed photography experiments for the combined seeding apparatus.The figure demonstrates that re-seeding and missed seeding are both observed during the seeding.The missed seeding is attributed to two aspects.On the one hand, the matching between the rotating speed parameters of the pneumatic and honeycomb seeding mechanisms results in a deviation of the seeds accurately dropping into the honeycomb seeding mechanism.On the other hand, the seeds do not drop into the hole in the honeycomb seeding mechanism exactly or even drop out of the mechanism.Meanwhile, two major reasons are summarized for re-seeding.One is that the seeds are stacked in the seed storage box of the pneumatic seeding mechanism and are subjected to compression and friction.In this case, multiple seeds may be sucked by the pneumatic seeding mechanism and then dropped into the honeycomb seeding mechanism.The other is that the seeds may fall on the edge of holes in the honeycomb seeding mechanism and then drop into the adjacent holes.Similarly, the lower the seeding rate, the better the operating performance of the co bined seeding apparatus.Thus, the optimal combination for a successful seeding rate A3B3C1, with 8.61 > 2.23 > 1.21.This means that the number of holes has the great impact on the re-seeding rate, followed by the diameter of holes and the seeding height turn.
Table 4 displays the variance of results of the orthogonal experiments.According the table, F0.1 (2, 6) = 3.46 is obtained.Comparison between it and the F-value in Table demonstrates that all the above three factors can affect the seeding success rate, of whi the number of holes in the honeycomb seeding disc exhibits the most significant impa while the diameter of holes and seeding height show slight impacts.Furthermore, it observed that all these three indicators affect the missed seeding rate and the re-seedi rate, with the number of holes exerting the greatest effects.The experimental indicators are required to achieve a higher seeding success ra while minimizing the missed seeding and re-seeding rates maximally.Based on a jo analysis of Tables 3 and 4, the optimal combination is determined as A3B2C1, with a see ing success rate of 81.63%, a missed seeding rate of 8.63%, and a re-seeding rate of 9.74

High-Speed Photography Experiments
Figure 13 illustrates the results of the high-speed photography experiments for t combined seeding apparatus.The figure demonstrates that re-seeding and missed seedi are both observed during the seeding.The missed seeding is attributed to two aspects.O the one hand, the matching between the rotating speed parameters of the pneumatic a honeycomb seeding mechanisms results in a deviation of the seeds accurately droppi into the honeycomb seeding mechanism.On the other hand, the seeds do not drop in the hole in the honeycomb seeding mechanism exactly or even drop out of the mechanis Meanwhile, two major reasons are summarized for re-seeding.One is that the seeds a stacked in the seed storage box of the pneumatic seeding mechanism and are subjected compression and friction.In this case, multiple seeds may be sucked by the pneuma seeding mechanism and then dropped into the honeycomb seeding mechanism.The oth is that the seeds may fall on the edge of holes in the honeycomb seeding mechanism a then drop into the adjacent holes.Similarly, the lower the seeding rate, the better the operating performance bined seeding apparatus.Thus, the optimal combination for a successful see A3B3C1, with 8.61 > 2.23 > 1.21.This means that the number of holes has impact on the re-seeding rate, followed by the diameter of holes and the seedi turn.
Table 4 displays the variance of results of the orthogonal experiments.A the table, F0.1 (2, 6) = 3.46 is obtained.Comparison between it and the F-valu demonstrates that all the above three factors can affect the seeding success ra the number of holes in the honeycomb seeding disc exhibits the most signific while the diameter of holes and seeding height show slight impacts.Furthe observed that all these three indicators affect the missed seeding rate and the rate, with the number of holes exerting the greatest effects.The experimental indicators are required to achieve a higher seeding while minimizing the missed seeding and re-seeding rates maximally.Base analysis of Tables 3 and 4, the optimal combination is determined as A3B2C1, ing success rate of 81.63%, a missed seeding rate of 8.63%, and a re-seeding ra

High-Speed Photography Experiments
Figure 13 illustrates the results of the high-speed photography experim combined seeding apparatus.The figure demonstrates that re-seeding and mis are both observed during the seeding.The missed seeding is attributed to two the one hand, the matching between the rotating speed parameters of the pne honeycomb seeding mechanisms results in a deviation of the seeds accurate into the honeycomb seeding mechanism.On the other hand, the seeds do no the hole in the honeycomb seeding mechanism exactly or even drop out of the Meanwhile, two major reasons are summarized for re-seeding.One is that th stacked in the seed storage box of the pneumatic seeding mechanism and are compression and friction.In this case, multiple seeds may be sucked by the seeding mechanism and then dropped into the honeycomb seeding mechanism is that the seeds may fall on the edge of holes in the honeycomb seeding mec then drop into the adjacent holes.Similarly, the lower the seeding rate, the better the operating per bined seeding apparatus.Thus, the optimal combination for a succ A3B3C1, with 8.61 > 2.23 > 1.21.This means that the number of h impact on the re-seeding rate, followed by the diameter of holes and turn.
Table 4 displays the variance of results of the orthogonal exper the table, F0.1 (2, 6) = 3.46 is obtained.Comparison between it and t demonstrates that all the above three factors can affect the seeding s the number of holes in the honeycomb seeding disc exhibits the mo while the diameter of holes and seeding height show slight impac observed that all these three indicators affect the missed seeding ra rate, with the number of holes exerting the greatest effects.The experimental indicators are required to achieve a higher while minimizing the missed seeding and re-seeding rates maxima analysis of Tables 3 and 4, the optimal combination is determined as ing success rate of 81.63%, a missed seeding rate of 8.63%, and a re-s

High-Speed Photography Experiments
Figure 13 illustrates the results of the high-speed photography combined seeding apparatus.The figure demonstrates that re-seedin are both observed during the seeding.The missed seeding is attribut the one hand, the matching between the rotating speed parameters o honeycomb seeding mechanisms results in a deviation of the seeds into the honeycomb seeding mechanism.On the other hand, the se the hole in the honeycomb seeding mechanism exactly or even drop o Meanwhile, two major reasons are summarized for re-seeding.One stacked in the seed storage box of the pneumatic seeding mechanism compression and friction.In this case, multiple seeds may be suck seeding mechanism and then dropped into the honeycomb seeding m is that the seeds may fall on the edge of holes in the honeycomb see then drop into the adjacent holes.Similarly, the lower the seeding rate, the better the oper bined seeding apparatus.Thus, the optimal combination f A3B3C1, with 8.61 > 2.23 > 1.21.This means that the num impact on the re-seeding rate, followed by the diameter of h turn.
Table 4 displays the variance of results of the orthogo the table, F0.1 (2, 6) = 3.46 is obtained.Comparison betwee demonstrates that all the above three factors can affect the the number of holes in the honeycomb seeding disc exhibi while the diameter of holes and seeding height show slig observed that all these three indicators affect the missed se rate, with the number of holes exerting the greatest effects.The experimental indicators are required to achieve while minimizing the missed seeding and re-seeding rate analysis of Tables 3 and 4, the optimal combination is determ ing success rate of 81.63%, a missed seeding rate of 8.63%, a

High-Speed Photography Experiments
Figure 13 illustrates the results of the high-speed pho combined seeding apparatus.The figure demonstrates that are both observed during the seeding.The missed seeding i the one hand, the matching between the rotating speed par honeycomb seeding mechanisms results in a deviation of into the honeycomb seeding mechanism.On the other han the hole in the honeycomb seeding mechanism exactly or ev Meanwhile, two major reasons are summarized for re-seed stacked in the seed storage box of the pneumatic seeding m compression and friction.In this case, multiple seeds may seeding mechanism and then dropped into the honeycomb is that the seeds may fall on the edge of holes in the honey then drop into the adjacent holes.Similarly, the lower the seeding rate, the bett bined seeding apparatus.Thus, the optimal com A3B3C1, with 8.61 > 2.23 > 1.21.This means th impact on the re-seeding rate, followed by the dia turn.
Table 4 displays the variance of results of th the table, F0.1 (2, 6) = 3.46 is obtained.Compariso demonstrates that all the above three factors can the number of holes in the honeycomb seeding d while the diameter of holes and seeding height observed that all these three indicators affect the rate, with the number of holes exerting the great The experimental indicators are required t while minimizing the missed seeding and re-se analysis of Tables 3 and 4, the optimal combinatio ing success rate of 81.63%, a missed seeding rate   Similarly, the lower the seeding ra bined seeding apparatus.Thus, the op A3B3C1, with 8.61 > 2.23 > 1.21.This impact on the re-seeding rate, followed turn.

High-Speed Photography Experiments
Table 4 displays the variance of re the table, F0.1 (2, 6) = 3.46 is obtained.demonstrates that all the above three f the number of holes in the honeycomb while the diameter of holes and seedi observed that all these three indicators rate, with the number of holes exerting The experimental indicators are while minimizing the missed seeding analysis of Tables 3 and 4, the optimal c ing success rate of 81.63%, a missed see   Similarly, the lower the bined seeding apparatus.Th A3B3C1, with 8.61 > 2.23 > impact on the re-seeding rate turn.

High-Speed Photography Experiments
Table 4 displays the var the table, F0.1 (2, 6) = 3.46 is demonstrates that all the abo the number of holes in the h while the diameter of holes observed that all these three rate, with the number of hol The experimental indic while minimizing the misse analysis of Tables 3 and 4, th ing success rate of 81.63%, a   The experime while minimizing analysis of Tables 3 ing success rate of   The experimental indicators are required to achieve a higher seeding success rate while minimizing the missed seeding and re-seeding rates maximally.Based on a joint analysis of Tables 3 and 4, the optimal combination is determined as A3B2C1, with a seeding success rate of 81.63%, a missed seeding rate of 8.63%, and a re-seeding rate of 9.74%.

High-Speed Photography Experiments
Figure 13 illustrates the results of the high-speed photography experiments for the combined seeding apparatus.The figure demonstrates that re-seeding and missed seeding are both observed during the seeding.The missed seeding is attributed to two aspects.On the one hand, the matching between the rotating speed parameters of the pneumatic and honeycomb seeding mechanisms results in a deviation of the seeds accurately dropping into the honeycomb seeding mechanism.On the other hand, the seeds do not drop into the hole in the honeycomb seeding mechanism exactly or even drop out of the mechanism.Meanwhile, two major reasons are summarized for re-seeding.One is that the seeds are stacked in the seed storage box of the pneumatic seeding mechanism and are subjected to compression and friction.In this case, multiple seeds may be sucked by the pneumatic seeding mechanism and then dropped into the honeycomb seeding mechanism.The other is that the seeds may fall on the edge of holes in the honeycomb seeding mechanism and then drop into the adjacent holes.

Discussion
The results of the ADAMS virtual experiment suggest that the seeding succe

Discussion
The results of the ADAMS virtual experiment suggest that the seeding success rate also increases with an increasing number and diameter of holes in the honeycomb seeding disc.Specifically, the seeding success rate is the highest, reaching 83.3%, when the number of holes in the honeycomb seeding disc is 24 or the diameter of the hole is 13 mm and 15 mm.In addition, it is observed that when the seeding height changes, the seeding success rate of the combined seeding apparatus is 83.3%, indicating that it is basically not affected by the seeding height.Based on joint consideration of external factors, in this paper, the seeding height is set to 60 mm.
The results of the single factor experiment reveal that as the number of holes increases, the seeding success rate of the combined seeding apparatus continuously increases, while the missed seeding and re-seeding rates decrease.When the number of holes is 24, the seeding success rate is 82.58%, the missed feeding rate is 8.21%, and the re-feeding rate is 9.21%.In this case, the combined seeding apparatus reaches the best performance state.As the diameter of the holes increases, the seeding success rate of the combined seeding apparatus continuously increases.When the diameter is 15 mm, the seeding success rate is 82.58%, the missed seeding rate is 8.21%, and the re-seeding rate is 9.21%.The performance of the combined seeding apparatus has reached its optimal state with the highest seeding success rate and the lowest missed seeding and re-seeding rates.As the seeding height increases, the seeding success rate continues to decrease.When the seeding height is 60 mm, the seeding success rate is the highest, reaching 82.58%, the missed seeding rate is 8.21%, and the re-seeding rate is 9.21%.The experimental results are consistent with those of the virtual experiment.Therefore, the research results of the paper are a useful reference for optimizing the operating parameters of the combined seeding apparatus, meeting the operational requirements of vegetable seeding.
Furthermore, the results of the high-speed photography experiment disclose that, during the seeding, the combined seeding apparatus experiences re-feeding and missed feeding.When the speed parameters of the pneumatic and honeycomb seeding mechanisms are not accurately matched, the seeds will not accurately drop into the holes in the honeycomb seeding mechanism and may even fall out of the mechanism, resulting in missed seeding.When the seeds pass through the pneumatic seeding mechanism, excessive air pressure from the fan can cause re-suction of the seeds, resulting in multiple seeds being sucked and dropping into the holes in the honeycomb seeding mechanism.In addition, the seeds with missed seeding will drop on the edge of holes in the honeycomb seeding mechanism and may drop into adjacent holes.These situations can all cause re-seeding in the combined seeding apparatus.The experimental results herein can provide a reference for analyzing the reasons for missed seeding and re-seeding of the combined seeding apparatus.

Conclusions
Concerning the low seeding efficiency and poor qualification rate of the current precision seeding apparatus for vegetable seeds, this paper designed a combined seeding apparatus and elaborated its operating principle.On this basis, it theoretically analyzed the operating process of combined seeding apparatus.Meanwhile, virtual experiments were performed on the combined seeding apparatus using ADAMS to simulate the changes in seed drop trajectory and seeding success rate under different structures and operating parameters.Finally, the influences of the number and diameter of the holes and seeding height of the honeycomb seeding mechanism on the operating performance of the combined seeding apparatus were analyzed by taking the bench test.The following conclusions are drawn: (1) Parameter equations were established for the speed and trajectory of seeds during the seeding for analysis to provide the theoretical foundation for installing the honeycomb seeding mechanism.Accordingly, a parameter equation was offered for the seeds during the seed dropping.It was then found that when the inclination angle of the holes in the honeycomb seeding disc is 2 • , the seed can roll off the honeycomb seeding disc.Therefore, the inclination angle of the hole should be 2 • in designing the honeycomb seeding mechanism.(2) With ADAMS, virtual experiments were performed on the designed combined seeding apparatus under different parameter conditions of the honeycomb seeding apparatus.
The results show that when the number and diameter of holes in the honeycomb seeding disc are 24 and 13 mm, respectively, the seeding success rate is the highest, both of which are 83.3%.Meanwhile, the results reveal that the seeding success rates are the same when the installation distances between two seeding mechanisms are different, suggesting that the seeding height presents a slight effect on the seeding success rate.The seeds may be affected by some external factors during dropping, so the distance between the two seeding mechanisms should be minimized as much as possible to reduce the influence on the success seeding.(3) Based on the single factor and orthogonal experiments on the parameters, the optimal parameter combinations of the combined seeding apparatus were determined.That is, the number and diameter of holes in the honeycomb seeding disc are 24 and 13 mm, respectively, and the seeding height is 60 mm.With these parameter settings, the seeding success rate is 81.63%, while the missed seeding rate and the re-seeding rate are 8.63% and 9.74%, respectively.The double-row seeding shows the best effect when the speed of the conveyor belt is 20 r/min, the row spacing is 80 mm, and the plant spacing is 51 mm.In addition, the high-speed camera shows that re-feeding and missed feeding occur during the running of the combined seeding apparatus.

Figure 7 .
Figure 7. Stress analysis of seed in the hole of mechanical seeding disc.

Figure 7 .
Figure 7. Stress analysis of seed in the hole of mechanical seeding disc.

Figure 10 .
Figure 10.The relationship of the number of honeycomb seeding disc holes.

Figure 11 .
Figure 11.The relationship curve of the diameter of the honeycomb seeding disc hole.

Figure 10 .
Figure 10.The relationship of the number of honeycomb seeding disc holes.

Figure 10 .
Figure 10.The relationship of the number of honeycomb seeding disc holes.

Figure 11 .
Figure 11.The relationship curve of the diameter of the honeycomb seeding disc hole.

Figure 11 .
Figure 11.The relationship curve of the diameter of the honeycomb seeding disc hole.

Figure 13
Figure13illustrates the results of the highcombined seeding apparatus.The figure demonst are both observed during the seeding.The missed the one hand, the matching between the rotating honeycomb seeding mechanisms results in a dev into the honeycomb seeding mechanism.On the the hole in the honeycomb seeding mechanism ex Meanwhile, two major reasons are summarized stacked in the seed storage box of the pneumatic compression and friction.In this case, multiple seeding mechanism and then dropped into the ho is that the seeds may fall on the edge of holes in then drop into the adjacent holes.

Figure 13
Figure13illustrates the results of combined seeding apparatus.The figur are both observed during the seeding.T the one hand, the matching between th honeycomb seeding mechanisms resu into the honeycomb seeding mechanis the hole in the honeycomb seeding mec Meanwhile, two major reasons are sum stacked in the seed storage box of the p compression and friction.In this case, seeding mechanism and then dropped is that the seeds may fall on the edge o then drop into the adjacent holes.

Figure 13 1 Processes
Figure 13 illustrates the combined seeding apparatus are both observed during the the one hand, the matching b honeycomb seeding mechan into the honeycomb seeding the hole in the honeycomb se Meanwhile, two major reaso stacked in the seed storage b compression and friction.In seeding mechanism and then is that the seeds may fall on then drop into the adjacent h Figure 13 illu combined seeding are both observed the one hand, the honeycomb seedin into the honeycom the hole in the hon Meanwhile, two m stacked in the seed compression and seeding mechanism is that the seeds m then drop into the

Processes 2023 , 1 Figure 13 .
Figure 13.Pictures of high-speed photography test of combined seed metering device.

Figure 13 .
Figure 13.Pictures of high-speed photography test of combined seed metering device.

Table 1 .
Orthogonal test factor level.

Table 2 .
Orthogonal test scheme and test results.

Table 3 .
Range analysis of orthogonal test results.

Table 3 .
Range analysis of orthogonal test results.

Table 4 .
Analysis of variance of orthogonal experiment results.

Table 3 .
Range analysis of orthogonal test results.

Table 4 .
Analysis of variance of orthogonal experiment results.

Table 3 .
Range analysis o

Table 4 .
Analysis of varia

Table 4 .
Analysis of variance of orthogonal experiment results.

Table 3 .
Range analysis of orthogonal test results.

Table 4 .
Analysis of variance of orthogonal experiment results.

Table 3 .
Range analysis of orthogonal test results.

Table 4 .
Analysis of variance of orthogonal experiment results.

Table 3 .
Range analysis of orthogonal test results.

Table 4 .
Analysis of variance of orthogonal experiment results.

Table 3 .
Range analysis of orthogonal test results.

Table 4 .
Analysis of variance of orthogonal experiment results.

Table 3 .
Range analysis of orthogonal test results.

Table 4 .
Analysis of variance of orthogonal experiment results.

Table 3 .
Range analysis of orthogonal test results.

Table 4 .
Analysis of variance of orthogonal experiment results.

Table 3 .
Range analysis of orthogonal test results.

Table 4 .
Analysis of variance of orthogonal experiment results.

Table 3 .
Range analysis of orthogonal test results.

Table 4 .
Analysis of variance of orthogonal experimen

Table 3 .
Range analysis of orthogonal test r

Table 4 .
Analysis of variance of orthogonal

Table 3 .
Range analysis of ortho

Table 4 .
Analysis of variance of

Table 4 .
Analysis of

Table 4 .
A