Detection Papers with Chromogenic Chemosensors for Direct Visual Detection and Distinction of Liquid Chemical Warfare Agents

: This work provides a summary of our results in the area of the experimental development of detection paper for the detection of liquid phase chemical warfare agents (drops, aerosol), the presence of which is demonstrated by the development of characteristic coloring visible to the naked eye. The basis of the detection paper is a cellulose carrier saturated with the dithienobenzotropone monomer (RM1a)–chromogenic chemosensor sensitive to nerve agents of the G type, blister agent lewisite, or choking agent diphosgene. We achieve a higher coloring brilliance and the limit certain interferences by using this chemosensor in the mix of the o -phenylendiamine-pyronine (PY-OPD). We prove that the addition of the Bromocresol Green pH indicator even enables detection of nerve agents of the V type, or, nitrogen mustards, while keeping a high stability of the detection paper and its functions for other chemical warfare agents. We resolve the resistance against the undesirable inﬂuence of water by providing a hydrophobic treatment of the carrier surface.


Introduction
Even though the Chemical Weapons Convention came into operation in 1997, and currently 193 countries participate (as of May 2018), the risk of chemical weapons proliferation and the threat of using them is still present: They can be used in local wars, civil wars, or in terrorist attacks [1,2].The active components of the chemical weapons are the chemical warfare agents (CWA), the combat employment of which depends to a significant extent on their state of matter.The most dangerous CWAs that have lethal effects are included within nerve agents, blister agents, and partially within choking agents.Most of them are in the liquid state, which enables their dispersion in the form of vapors, or variously dispersed liquid aerosols, with the potential of easy penetration not only through airways, but through the skin as well, resulting in serious percutaneous poisoning.Some of these CWAs are highly persistent, therefore they can contaminate the terrain for a long time, depending on actual climatic conditions and on the terrain characteristics [3].The chemical structure of the most significant liquid CWA is shown in Figure 1.Some of their physical and toxic properties are provided in Table 1.
Chemosensors 2019, 7, x FOR PEER REVIEW 2 of 12 significant liquid CWA is shown in Figure 1.Some of their physical and toxic properties are provided in Table 1.For the detection of settling liquid particles of the CWA aerosol cloud, or droplets or spray of a liquid CWA on the surface of the terrain, objects, machines, and persons, simple technical means are usually used, based on visual evaluation (by naked eye) of color changes.The color change results from the solubility of organic dyes, color change of pH indicator, or from the reaction with specific chromogenic agents.The organic dyes, pH indicators, and chromogenic agents are applied to the filtration paper, fabric, or another flat porous carrier, modified to the form of detection strips, papers and/or tapes.
In the past, the main focus was given to the detection of sulfur mustard, a typical poison with percutaneous effect (that is why it is called a "blister agent").As an example, there was the detection paper saturated with 1-(p-nitrophenylazo)-2-naphtylamine, providing a red color with the sulfur mustard.Later, this dye was replaced with a less toxic compound and used not only for the detection of sulfur mustard, but also for the detection of nerve agents.Another example is the detection paper saturated with the complex of Crystal Violet with Hg 2+ and Cu 2+ salts, providing a dark violet color with the droplets of the sulfur mustard, due to the release of the original dye [4], or the detection paper with 4,4′-bis(N,N-dimethylamino)benzophenone and mercuric chloride, providing a red color with the sulfur mustard [5].For the detection of settling liquid particles of the CWA aerosol cloud, or droplets or spray of a liquid CWA on the surface of the terrain, objects, machines, and persons, simple technical means are usually used, based on visual evaluation (by naked eye) of color changes.The color change results from the solubility of organic dyes, color change of pH indicator, or from the reaction with specific chromogenic agents.The organic dyes, pH indicators, and chromogenic agents are applied to the filtration paper, fabric, or another flat porous carrier, modified to the form of detection strips, papers and/or tapes.
In the past, the main focus was given to the detection of sulfur mustard, a typical poison with percutaneous effect (that is why it is called a "blister agent").As an example, there was the detection paper saturated with 1-(p-nitrophenylazo)-2-naphtylamine, providing a red color with the sulfur mustard.Later, this dye was replaced with a less toxic compound and used not only for the detection of sulfur mustard, but also for the detection of nerve agents.Another example is the detection paper saturated with the complex of Crystal Violet with Hg 2+ and Cu 2+ salts, providing a dark violet color with the droplets of the sulfur mustard, due to the release of the original dye [4], or the detection paper with 4,4 -bis(N,N-dimethylamino)benzophenone and mercuric chloride, providing a red color with the sulfur mustard [5].
The introduction of nerve agents to military equipment, and the real threat of using them, also calls for the introduction of a simple means for their detection in the liquid phase.An example is the detection paper impregnated with the Bromocresol Green pH indicator, providing a blue color in contact with the VX agent.At present, multicomponent detection papers are used, intended not only for the detection of nerve agents, but also for the detection of sulfur mustard, with the option of their distinction.They are usually self-sticking paper sheets impregnated with a mixture of organic dyes, which dissolve in liquid CWA and provide characteristic colors.The Dye Red E (CAS: 60033-00-3) is used for the detection of sulfur mustard, the Dye Green EDA (CAS: 5833-18-1) is used, as an example, for the detection of nerve agents of the V type, and the Disperse Yellow 23 (CAS: 6250-23-3) dye is used for the detection of G type nerve agents, providing red, green, and yellow colours [4,6].
The low selectivity of the known methods of the detection of liquid CWAs, based on the solubility of organic dyes or pH indicators, is a significant disadvantage.Chemical reactions are more selective, but the selection of chromogenic agents, suitable for practical applications, was very limited in the past.However, during the last two decades, a lot of original works were published, referring particularly to chromogenic chemosensors for the G type nerve agents, featuring a significant change of color as well as good selectivity and sensitivity; these chemosensors are based on hydroxyl-activation, N-activation, and contain metal ions (coordination compounds), or possibly form reactive polymers [7][8][9][10][11][12][13][14][15][16][17][18][19].Many publications deal with new chemosensors for sulphur mustard [20][21][22][23][24].The issue is that most of these chemosensors have only been verified using simulants (e.g., diethyl chlorophosphate (DCP), 2-chloroethyl ethyl sulfide (CEES), etc.), moreover, they have not been applied on the detection papers for the detection in the liquid phase.
The goal of this text is to report the results of the experimental development of detection papers for the detection of CWAs in liquid phase, using the already known chemosensor based on the dithienobenzotropone [9], in combination with the chemosensor based on the o-phenylenediamine-pyronin [11], and the Bromocresol Green pH indicator.The article provides the method of detection papers preparation, their response to real CWAs, chemical interferences and stability during storage and operational ingestion.Basically, they are simple, robust, sufficiently selective, and reliable detection systems for most of the potential liquid CWA, with the exception of the sulfur mustard.
As for the CWA test we used tabun (GA), sarin (GB), soman (GD), cyclosarin (GF), VX, RVX ("Russian VX"), sulfur mustard (HD), nitrogen mustard (HN-1, HN-2, HN-3), lewisite (L-1, L-2, L-3), and diphosgene (DP), all of them provided by the Military Research Institute, Brno, Czech Republic.For the research tasks, we used DCP and CEES simulants, both made by Sigma-Aldrich.All CWAs were prepared and tested in facilities declared within OPCW (Organization for the Prohibition of Chemical Weapons).Certified protection equipment was used during all experiments, and all waste was treated using chloramine solution in 10% NaOH in the water-ethanol mixture (1:1) prior to disposal.
For the objective measurement of selected parameters (detection paper ageing), we used a portable tristimulus colorimeter LMG 173 (Dr.Lange, Dusseldorf, Germany), which utilizes the color CIE-Lab system.Spectrophotometric measurement (absorption spectra) were performed using a spectrophotometer Aquamate (Thermo Spectronic, Cambridge, UK).
The impregnated filtration papers were dried in open air for 60 min and stored in a hermetically closed package and kept away from direct sunlight.

Testing the Detection Paper Functions
Droplets of test substances (5 µL) were applied using a micropipette on the detection paper and were evaluated visually (by naked eye) for color change at the point of exposure.Each test was repeated 3× using 2 lots of real CWA (the same manufacturer, different production dates).All results were documented using a photographic camera within 1 min after exposure.

Testing of Stability
For the purpose of the stability testing, the detection papers were stored in the laboratory in the open air, at a temperature of 21-23 • C, for a period of 6 months.Papers were visually monitored on a regular basis once a week for surface color change without any exposure to the CWA droplets and for their function-color change after the exposure to the CWA droplets.Thermal stability was proved with part of the samples.The samples were stored in a drying cabinet at a temperature of 80 • C for three weeks.On a regular basis, the unexposed surface color change was monitored visually using the tristimulus colorimeter (CIE-Lab color system) following the ∆E parameter as the analytical signal [25].The ∆E values up to 0.2 cannot be perceived by the naked eye, the values of 0.2-0.5 are very slight, 0.5-1.5 are slight, 1.5-3.0 are distinct, 3.3-6.0are very distinct, 6.0-12.0 are strong, and above 12.0, the values are very strong.In addition, the function of the detection paper (visual control of the color change after CWA exposure) was tested regularly.

Design of the RM1a Detection Paper or RM1a/PY-OPD
The first (basic) design of the novel detection paper was based on the intention of developing a detection paper with high selectivity for G type nerve agents, for which detection using existing technical means is an issue.E.g., the 3-way detection papers (M8, PDF-1, PP-3, CALID-3, and similar) provide a relatively faint yellow color with the G type nerve agents droplets (on a grey background), which is disturbed with the presence of common organic solvents and industrial chemicals; the M9 detection paper provides an even lower selectivity as we verified the selectivity of these means experimentally.
By studying the latest sources, we selected, synthesized, and verified many chemosensors, potentially sensitive to alkyl/cycloalkyl-methylphosphonofluoridates.The RM1a appeared to be the most interesting, with its colorless chloroform solution, providing red color with the DCP (according to literary data), with a bathochromic shift from 330 to 580 nm [9].The agent was not verified against real CWA, neither on a solid carrier, nor in the form of the detection paper for the detection in the liquid phase.
During the experiments, we found the RM1a was not only a good chemosensor of current G type nerve agents, but also that it is very stable and functional on the cellulose carrier.Moreover, the structurally different GA (reaction on the P-CN bond), blister agent L, and choking agent DP were giving a uniquely positive response.The reaction mechanism for the alkyl/cycloalkyl-methylphosphonofluoridates is provided in Figure 2.  The extended design was based on two presumptions: The reaction product color intensity can be increased, or, the color contrast can be improved and the detection selectivity can be increased.With this goal, we combined the RM1a with some chemosensors for alkylating or acylating agents.The combination with the PY-OPD provided good results.This chemosensor had been designed before for the detection of DCP and phosgene, providing yellow and violet color with them in the gaseous phase, respectively [11].The reaction mechanism with DP comprising intramolecular cyclisation is provided in Figure 3. Examples of absorption spectra of RM1a, PY-OPD and RM1a/PY-OPD (in chloroform solution) after addition of GD are shown in Figure 4.The addition of PY-OPD featured two advantages.At first, the detection paper exposed to droplets of the G type nerve agents provided the color change of yellow-red, which is more suitable for the visual evaluation by the naked eye, compared to the white-red color change of the RM1a itself.Secondly, a different color was created upon contact with the liquid DP, compared to the G type nerve agents, thus improving the detection selectivity.The other parameters of the detection paper have been maintained.The color response of RM1a and RM1a/PY-OPD detection papers to real CWAs are documented in Figure 5.The extended design was based on two presumptions: The reaction product color intensity can be increased, or, the color contrast can be improved and the detection selectivity can be increased.With this goal, we combined the RM1a with some chemosensors for alkylating or acylating agents.The combination with the PY-OPD provided good results.This chemosensor had been designed before for the detection of DCP and phosgene, providing yellow and violet color with them in the gaseous phase, respectively [11].The reaction mechanism with DP comprising intramolecular cyclisation is provided in Figure 3. Examples of absorption spectra of RM1a, PY-OPD and RM1a/PY-OPD (in chloroform solution) after addition of GD are shown in Figure 4.The addition of PY-OPD featured two advantages.At first, the detection paper exposed to droplets of the G type nerve agents provided the color change of yellow-red, which is more suitable for the visual evaluation by the naked eye, compared to the white-red color change of the RM1a itself.Secondly, a different color was created upon contact with the liquid DP, compared to the G type nerve agents, thus improving the detection selectivity.The other parameters of the detection paper have been maintained.The color response of RM1a and RM1a/PY-OPD detection papers to real CWAs are documented in Figure 5.
featured two advantages.At first, the detection paper exposed to droplets of the G type nerve agents provided the color change of yellow-red, which is more suitable for the visual evaluation by the naked eye, compared to the white-red color change of the RM1a itself.Secondly, a different color was created upon contact with the liquid DP, compared to the G type nerve agents, thus improving the detection selectivity.The other parameters of the detection paper have been maintained.The color response of RM1a and RM1a/PY-OPD detection papers to real CWAs are documented in Figure 5.

Design of the RM1a/PY-OPD/BCG Detection Paper
Another design covered the option of detecting droplets and aerosol of the V type nerve agents, representing the top of CWAs for their toxicity and persistence.We proceeded based on a simple plan: To the RM1a/PY-OPD detection paper, we incorporated (by adding to an impregnating solution) various chemosensors of amines, thiols, and aminothiols as precursors, or products of these

Design of the RM1a/PY-OPD/BCG Detection Paper
Another design covered the option of detecting droplets and aerosol of the V type nerve agents, representing the top of CWAs for their toxicity and persistence.We proceeded based on a simple plan: To the RM1a/PY-OPD detection paper, we incorporated (by adding to an impregnating solution) various chemosensors of amines, thiols, and aminothiols as precursors, or products of these CWA hydrolysis.We verified 5,5 -dithiobis(2-nitrobenzoic acid), 2,2 -dithiobis(5-nitropyridine), 4-chloro-7-nitrobenzofurazan, 4-chloro-5,7-dinitrobenzofurazan, and 4-nitro-2,1,3-benzothiadiazol as chromogenic reagents.In this investigation phase, the most promising results were provided by common color pH indicators, in particular by the triphenylmethane BCG indicator, providing the color change yellow (3.8)-blue (5.4).The BCG color change mechanism scheme is shown in Figure 6.Practically, the BCG incorporation to the RM1a/PY-OPD detection paper did not change its appearance, or dispositions to reactions with G type nerve agents (namely, the semi-persistent GD and GF), or, lewisite or DP, moreover, it provided an expressive blue color with the V type nerve agents.As expected, the HN-1 and HN-2 nitrogen mustards gave a response resulting in a green color (these vesicants are less basic than VX); the HN-3 nitrogen mustard did not react at all.The summary of color responses of RM1a/PY-OPD/BCG detection papers to CWA is shown in Figure 7.A summary overview of detection papers color changes, supplemented with selected physical and toxic properties, is provided in Table 1.

Design of the RM1a/PY-OPD/BCG Detection Paper
Another design covered the option of detecting droplets and aerosol of the V type nerve agents, representing the top of CWAs for their toxicity and persistence.We proceeded based on a simple plan: To the RM1a/PY-OPD detection paper, we incorporated (by adding to an impregnating solution) various chemosensors of amines, thiols, and aminothiols as precursors, or products of these CWA hydrolysis.We verified 5,5′-dithiobis(2-nitrobenzoic acid), 2,2′-dithiobis(5-nitropyridine), 4chloro-7-nitrobenzofurazan, 4-chloro-5,7-dinitrobenzofurazan, and 4-nitro-2,1,3-benzothiadiazol as chromogenic reagents.In this investigation phase, the most promising results were provided by common color pH indicators, in particular by the triphenylmethane BCG indicator, providing the color change yellow (3.8)-blue (5.4).The BCG color change mechanism scheme is shown in Figure 6.Practically, the BCG incorporation to the RM1a/PY-OPD detection paper did not change its appearance, or dispositions to reactions with G type nerve agents (namely, the semi-persistent GD and GF), or, lewisite or DP, moreover, it provided an expressive blue color with the V type nerve agents.As expected, the HN-1 and HN-2 nitrogen mustards gave a response resulting in a green color (these vesicants are less basic than VX); the HN-3 nitrogen mustard did not react at all.The summary of color responses of RM1a/PY-OPD/BCG detection papers to CWA is shown in Figure 7.A summary overview of detection papers color changes, supplemented with selected physical and toxic properties, is provided in Table 1.

Sulphur Mustard Tests
During the development of the detection paper, we also studied the option of using new specific chromogenic/fluorogenic reagents, potentially sensitive to sulfur mustard.Based on the literature, we synthesized and verified the reagents based on rhodamine-thioamide [21], benzothiazole (RHBT) [22], and pyronine (DPXT) [24].We used solutions of reagents in common organic solvents (methanol, ethanol, chloroform) for the impregnation of the cellulose carrier, and after drying, we exposed it to droplets of sulfur mustard (HD) and simulant (CEES).However, we did not succeed in obtaining any positive color response.

Stability
In practice, the detection papers for liquid CWAs are usually stored in closed packages, at a temperature of −40 to +40 • C (at a temperature of 60 • C up to one month maximally), and they should be functional (operationally usable) at a temperature of −40 to +60 • C [26].The samples of RM1a, RM1a/PY-OPD and RM1a/PY-OPD/BCG detection papers, stored at a common laboratory temperature, did not show any changes in their appearance or loss of functions during the full six months.At the same time, we tested the heat stability with the goal of verifying the detection paper resistance against short-term extreme temperatures, which might occur both during storage and during operational usage.
The change of detection papers appearance exposed to a temperature of 80 • C is shown in Figure 8.The charts show that a more significant darkening of the combined systems occurred during the first 24 h, then their appearance was stabilized.In the case of the RM1a detection paper, a slow darkening occurred from the very beginning.Yet, the detection papers maintained their functions, as noticeable on the RM1a/PY-OPD/BCG complex system example in Figure 9.
Chemosensors 2019, 7, x FOR PEER REVIEW 8 of 12 first 24 h, then their appearance was stabilized.In the case of the RM1a detection paper, a slow darkening occurred from the very beginning.Yet, the detection papers maintained their functions, as noticeable on the RM1a/PY-OPD/BCG complex system example in Figure 9.

Interferences
We also paid attention to the study of interferences of chemical substances, which are not CWAs, but might be present as stabilizers, tactical ingredients, or might be present for other reasons.We verified the representatives of all types of organic solvents (polar, non-polar, aprotic) for causing interferences, as well as other chemicals.The RM1a detection papers, or, the RM1a/PY-OPD detection papers proved themselves as being highly resistant against the interferences, only the acetic acid provided a color response; the circles at RM1a/PY-OPD were created due to "reagent elution" (Figure 10).The RM1a/PY-OPD/BCG detection papers were less resistant against the interference with these organic compounds, but still much more resistant than known M8, M9, CALID-3 detectors (we verified the selectivity of these detectors experimentally).first 24 h, then their appearance was stabilized.In the case of the RM1a detection paper, a slow darkening occurred from the very beginning.Yet, the detection papers maintained their functions, as noticeable on the RM1a/PY-OPD/BCG complex system example in Figure 9.

Interferences
We also paid attention to the study of interferences of chemical substances, which are not CWAs, but might be present as stabilizers, tactical ingredients, or might be present for other reasons.We verified the representatives of all types of organic solvents (polar, non-polar, aprotic) for causing interferences, as well as other chemicals.The RM1a detection papers, or, the RM1a/PY-OPD detection papers proved themselves as being highly resistant against the interferences, only the acetic acid provided a color response; the circles at RM1a/PY-OPD were created due to "reagent elution" (Figure 10).The RM1a/PY-OPD/BCG detection papers were less resistant against the interference with these organic compounds, but still much more resistant than known M8, M9, CALID-3 detectors (we verified the selectivity of these detectors experimentally).

Interferences
We also paid attention to the study of interferences of chemical substances, which are not CWAs, but might be present as stabilizers, tactical ingredients, or might be present for other reasons.We verified the representatives of all types of organic solvents (polar, non-polar, aprotic) for causing interferences, as well as other chemicals.The RM1a detection papers, or, the RM1a/PY-OPD detection papers proved themselves as being highly resistant against the interferences, only the acetic acid provided a color response; the circles at RM1a/PY-OPD were created due to "reagent elution" (Figure 10).The RM1a/PY-OPD/BCG detection papers were less resistant against the interference with these organic compounds, but still much more resistant than known M8, M9, CALID-3 detectors (we verified the selectivity of these detectors experimentally).The influence of water is shown to be an issue.In liquid CWAs, there is no water present, so its interference can practically be neglected from this point of view.However, water can be present as a medium of other toxic substances (such as pesticides), which may be sprayed, or it can be present as a rain or fog.We proved the RM1a and RM1a/PY-OPD detection papers were resistant against water drops.Unlike the reaction of the RM1a/PY-OPD/BCG, detection paper's reaction to water created only smaller, but relatively intensive green dots.For this reason, we modified the surface of the detection paper with hydrophobic colophon resin, which prevents the contact of chemosensors (preferentially with BCG) with water, but it lets the liquid CWA get through and does not block their color response.The disadvantage of the colophon resin is its content of an acid ingredient (abietic acid), which affects the color hues of the stains to a certain extent (this was apparent at V agents, showing a blue-green shift).The appearance of color stains before and after the modification of the RM1a/PY-OPD/BCG detection paper using the colophon is documented in Figure 11.The influence of water is shown to be an issue.In liquid CWAs, there is no water present, so its interference can practically be neglected from this point of view.However, water can be present as a medium of other toxic substances (such as pesticides), which may be sprayed, or it can be present as a rain or fog.We proved the RM1a and RM1a/PY-OPD detection papers were resistant against water drops.Unlike the reaction of the RM1a/PY-OPD/BCG, detection paper's reaction to water created only smaller, but relatively intensive green dots.For this reason, we modified the surface of the detection paper with hydrophobic colophon resin, which prevents the contact of chemosensors (preferentially with BCG) with water, but it lets the liquid CWA get through and does not block their color response.The disadvantage of the colophon resin is its content of an acid ingredient (abietic acid), which affects the color hues of the stains to a certain extent (this was apparent at V agents, showing a blue-green shift).The appearance of color stains before and after the modification of the RM1a/PY-OPD/BCG detection paper using the colophon is documented in Figure 11.

Effects of Dilution
One of the basic characteristics of CWA detection papers is that they must allow the detection of substances in their concentrated form, or in mixture with stabilizers or thickeners.By this, the issue of the detection limit gets significantly simplified.You might even say that the relatively lower sensitivity is rather an advantage for the detection of droplets, since many potential interferences are eliminated in this way.Despite this, we verified the influence of the dilution of real CWA (in chloroform) to the intensity of generated color, or, to the detection paper function.In Figure 12, it is proved that the RM1a/PY-OPD/BCG/colophon detection paper (as the most complex of all designed detectors) provided a color response even after the 100-fold dilution of GD or 1000-fold dilution of VX.In conclusion, the detection limits of CWAs (nerve agents, lewisite, DP) range from 0.001 to 0.1 mg/µL, which satisfies the requirements for their detection in the liquid phase (for example, primary liquid aerosol cloud) in field conditions.Color response (a) RM1a/PY-OPD/BCG, (b) RM1a/PY-OPD/BCG/colophon to selected chemicals (DMSO-dimethyl sulfoxide, DMF-dimethylformamide, DCMP-diethyl cyanomethylphosphonate, DETA-diethylenetriamine).

Effects of Dilution
One of the basic characteristics of CWA detection papers is that they must allow the detection of substances in their concentrated form, or in mixture with stabilizers or thickeners.By this, the issue of the detection limit gets significantly simplified.You might even say that the relatively lower sensitivity is rather an advantage for the detection of droplets, since many potential interferences are eliminated in this way.Despite this, we verified the influence of the dilution of real CWA (in chloroform) to the intensity of generated color, or, to the detection paper function.In Figure 12, it is proved that the RM1a/PY-OPD/BCG/colophon detection paper (as the most complex of all designed detectors) provided a color response even after the 100-fold dilution of GD or 1000-fold dilution of VX.In conclusion, the detection limits of CWAs (nerve agents, lewisite, DP) range from 0.001 to 0.1 mg/µL, which satisfies the requirements for their detection in the liquid phase (for example, primary liquid aerosol cloud) in field conditions.

Conclusions
The results of the experimental development of detection paper for the detection of CWAs in liquid phase showed that the strategy of usage and the combination of the latest world findings in the area of the investigation of chromogenic sensors (RM1a, PY-OPD) with traditional analytical agents (BCG) is highly effective.This strategy enabled the authors to design and verify the detection papers for a whole range of potential CWA, which might occur in the form of droplets, or variously dispersed aerosol, even with the possibility of their color distinction.Practically, the only CWA which did not provide a positive color response, was sulfur mustard.Greater efforts will therefore be dedicated to this resolving this issue in the future.

Figure 5 .
Figure 5. RM1a (a) and RM1a/PY-OPD (b) detection paper after the exposure to a droplet of CWA.

Figure 5 .
Figure 5. RM1a (a) and RM1a/PY-OPD (b) detection paper after the exposure to a droplet of CWA.

Figure 8 .Figure 9 .
Figure 8. Color stability of detection papers during storage at a temperature of 80 °C (tristimulus colorimetric measurement of the surface color change).

Figure 8 .
Figure 8. Color stability of detection papers during storage at a temperature of 80 • C (tristimulus colorimetric measurement of the surface color change).

Figure 8 .Figure 9 .
Figure 8. Color stability of detection papers during storage at a temperature of 80 °C (tristimulus colorimetric measurement of the surface color change).

Figure 9 .
Figure 9. Functional stability of the RM1a/PY-OPD/BCG detection paper after 20 days of storage at a temperature of 80 • C.

Table 1 .
The summary of tested CWAs, their physical and toxic properties and reactions with detection papers (− no response, + distinct response, ++ strong response).

Table 1 .
The summary of tested CWAs, their physical and toxic properties and reactions with detection papers (− no response, + distinct response, ++ strong response).