Mechanical Properties of Ballastless Track Considering Freeze–Thaw Deterioration Damage

: In order to investigate the stress characteristics of ballastless track under high latitude, and multi-source and multi-ﬁeld extreme temperature conditions. Based on the ﬁnite element theory and the elastic foundation beam–plate principle, a ﬁnite element model of the ballastless track considering the limit convex abutment, gel resin, and interlayer bonding is established. The mechanical characteristics of the ballastless track under the slab–CAM layer bonding state, mortar separation, freeze–thaw degradation and forced deformation of the foundation are studied. Considering the deterioration of materials, the bending moment and reinforcement of track structures in cold regions are checked and calculated. The studies show that under the action of negative temperature gradient load, the edge of the track slab is subjected to tension, and structural separation occurs at the edge of the slab. When the interface between the track slab–CAM layer is poorly bonded, the bearing capacity can be improved, and the amount of separation can be reduced by increasing the structural stiffness of the CAM layer. Under the action of freeze–thaw cycles, the material performance deteriorates seriously, the separation between the track structures intensiﬁes, the baseplate is seriously powdered and cracked, and the maximum tensile stress exceeds 6 MPa. The CAM layer and the baseplate are weak structures, and the foundation frost heave occurs at the expansion joint of the baseplate, which is the frost heave condition. Under freeze–thaw deterioration, the original reinforcement design of the substructure structure does not meet the requirements of structural cracks and reinforcement yield stress. In severely cold areas, the structural reinforcement scheme should be reasonably determined.


Introduction
Ballastless tracks are different from ballasted tracks; in addition to providing track elasticity, cushioning and shock absorption, the reinforced concrete structure has strong integrity, which can greatly reduce the accumulation of residual deformation in the track structure and maintain uniform stiffness [1,2].Considering the construction characteristics and construction techniques used in track structures, under extreme temperature conditions such as those in extreme climate areas and subgrade frost heave and thawing areas, prefabricated slab unit ballastless track structures with low interoperability are often used to reduce the potential damage to the track structure under extreme load conditions.Climatic disasters such as seasonal frozen soil, upper arch, moisture, and differences in temperature may occur in regions with extreme climates.Scholars have conducted extensive and in-depth research on the stress damage law of ballastless track in cold regions, including the transition section of subgrades and bridges [3], the sunny side and shady side of track structures [4,5], etc.The influence of temperature load [6], train load [7,8], foundation deformation [9], and other external factors on the mechanical properties of track systems have been studied.Zeng, ZP et al. [10] used the finite element software ABAQUS to establish a temperature field analysis model for a double-block ballastless track on the basis of test data, solar radiation theory and boundary heat transfer theory, and studied the influence of different routes and geographical latitudes on the temperature field.Dai Gonglian et al. [11] used the non-thickness interface bonding element to simulate the bonding contact force between the track plate and the mortar layer.Considering the interface bonding strength, interface shear load, and damage range of the track plate and the mortar layer, the failure mechanism of interface between the slab and the ballastless track was discussed; it was proved that the blade load at the edge of track plate and the mortar plate was the largest, and gradually decreased to the interior.Jiang, HG et al. [12] established a three-dimensional finite element model considering the contact between different layers in order to be able to simulate different settlement scenarios.The numerical results were verified by comparing the rail deflection with the full-scale physical model test.A unified formula for settlement amplitude and equivalent track flexibility was proposed to describe the geometric mapping relationship.
In view of the extremely prominent problems of material damage due to freeze-thaw cycles and the impact on the bonding state of subgrade thawing and frost heave under extreme temperature load in cold regions, the currently available studies related to the smoothness and mechanical characteristics of ballastless tracks on subgrades are still insufficient, and there is still relatively little research on the damage and deterioration of track structures under the coupling effect of subgrade freeze-thaw cycles and frost heave.Primarily, the stress checking of ballastless track structures does not take into account the impact of reductions in material properties.It is necessary to study the interaction damage characteristics of ballastless tracks in cold regions at high latitudes.
Due to the relatively limited amount of research performed by domestic and foreign scholars on the damage to and deterioration of track structures under the coupling effect of roadbed freeze-thaw cycles and frost heave, the performance reduction state of concrete materials is still unclear.In this paper, a nonlinear refined finite element model considering the limiting stop boss, annular gel resin, and interlayer bonding contact characteristics of a ballastless track on a subgrade is established to investigate the mechanical characteristics of ballastless tracks under multi-source and multi-field coupling effects.These include the structural bonding state, mortar disjoint, material freeze-thaw deterioration, and forced deformation of the foundation under extreme temperature conditions.Then, based on the principle of the beam-sheet plate, and considering the deterioration of ballastless track materials, the structural reinforcement in severely cold areas is checked and calculated.The stress state and damage characteristics of ballastless track structures in areas subject to seasonal freezing are revealed.

Finite Element Model of Ballastless Track
Ballastless track systems primarily consist of rails, fasteners, track slab, CA mortar layer, gel resin, a limit stop and baseplate, etc. [13,14].Vertical and transverse fasteners adopt linear spring elements, while longitudinal fasteners adopt nonlinear spring elements.CRTS I type ballastless track fastener systems adopt the WJ-7B type normal resistance fastener; the lateral stiffness of the fastener system is 3.5 × 10 7 N/m, and vertical stiffness is 5 × 10 7 N/m.The longitudinal deformation resistance values of the fastener are shown in Formula (1) [15]: where r is the longitudinal resistance of the fastener (kN), and x is the longitudinal relative displacement between the rail and the rail bearing platform (mm).The rail is equivalent to a Euler beam, which is supported by an elastic point and simulated by means of a beam188-type element; a combin14-type element is adopted for the fastener, and the track structures and subgrade are simulated by means of a solid45-type element.The finite element model, consisting of 145,356 nodes and 54,508 elements, is shown in Figure 1.The rail linear expansion coefficient is 1.18 × 10 −5 /°C, and the concrete linear expansion coefficient is 1.0 × 10 −5 /°C.The parameters of the ballastless track system are shown in Table 1.The rail linear expansion coefficient is 1.18 × 10 −5 / • C, and the concrete linear expansion coefficient is 1.0 × 10 −5 / • C. The parameters of the ballastless track system are shown in Table 1.

Temperature Load Mode
Temperature load is mainly divided into overall temperature load, temperature gradient load and concrete shrinkage and creep.The main structure of the ballastless track is made of concrete material, which is highly sensitive to temperature.Due to the differences in the material properties of the vertical layered structure of the track, the influence of the vertical temperature gradient load is the most significant.
Ballastless tracks are long strip structures with small contact surfaces between the sides and the air, which only affects the structural corners of the ballastless track.The temperature field model of a ballastless track can be simplified into a vertical one-dimensional linear heat transfer model, expressed as follows: where T is the temperature; t is the time; ξ is the thermal conductivity coefficient; z is the distance from the top surface of the structure.Then, adopting the third type of boundary condition in heat conduction theory: where T b is the atmospheric temperature; Q J is the net radiation of the ballastless track; B is the heat release coefficient of the road surface, taken to be B = 5.7 + 4v; and v is the daily average wind speed; λ is the thermal conductivity of the concrete material.
The boundary temperature Ta of the track structure is: where T 1 is the daily average temperature; T 2 is the daily average increase; t 0 is the initial phase, usually taken to be 9; and ω is the internal angular frequency of one day.
Taking the climate parameters of the ballastless track structure in typical regions of China as an example, the meteorological data of Harbin in regions characterized by severe cold were selected, and the time history curve of vertical temperature load change in ballastless track slab structure within the annual range was obtained by solving the above equations, as shown in Figure 2.
where T is the temperature; t is the time; ξ is the thermal conductivity coefficient; z is the distance from the top surface of the structure.
Then, adopting the third type of boundary condition in heat conduction theory: Where b T is the atmospheric temperature; J Q is the net radiation of the ballastless track; B is the heat release coefficient of the road surface, taken to be 5.7 4 B v = + ; and v is the daily average wind speed; λ is the thermal conductivity of the concrete material.
The boundary temperature Ta of the track structure is: where 1 T is the daily average temperature; 2 T is the daily average increase; 0 t is the ini- tial phase, usually taken to be 9; and ω is the internal angular frequency of one day.
Taking the climate parameters of the ballastless track structure in typical regions of China as an example, the meteorological data of Harbin in regions characterized by severe cold were selected, and the time history curve of vertical temperature load change in ballastless track slab structure within the annual range was obtained by solving the above equations, as shown in Figure 2. The reliability of the temperature gradient load can be verified on the basis of a comparison with the relevant literature [16] and the code for design of highway cement concrete pavement [17].There are many studies providing a relatively complete analysis and discussion of the mechanical properties of track structures under single temperature gradient loads.Considering extreme temperature load conditions, the negative temperature gradient load is taken to be −50 °C/m, and the overall temperature load of the track slab is taken to be −5 °C for temperature superposition, that is, when the negative temperature gradient load is taken, the temperature of the track slab bottom is 0 °C, decreasing linearly to −10 °C at the track slab surface.
Under the action of a negative temperature gradient load, the dead weight is not able to completely restrain the temperature warping deformation of the track slab, resulting in poor contact between the track slab and the mortar cushion, local voids, and uneven stress.Under the action of train load, a "slap" effect will be produced, which will lead to mortar separation and damage.Under the action of a negative temperature gradient, the maximum longitudinal stress of the track slab will occur at the lower surface of both sides, and the maximum transverse stress will occur at the junction of the track slab and the lower surface of the limit stop.When studying the temperature load effect, it is necessary to consider the bonding state of the track slab and the mortar layer, which can be divided into two states: good bonding and poor bonding.Good bonding means that the mortar cushion was constructed using the formwork method, while poor bonding means that the mortar cushion was constructed using the bagging method.The interface transmits the vertical and horizontal temperature force through friction, and the friction coefficient is The reliability of the temperature gradient load can be verified on the basis of a comparison with the relevant literature [16] and the code for design of highway cement concrete pavement [17].There are many studies providing a relatively complete analysis and discussion of the mechanical properties of track structures under single temperature gradient loads.Considering extreme temperature load conditions, the negative temperature gradient load is taken to be −50 • C/m, and the overall temperature load of the track slab is taken to be −5 • C for temperature superposition, that is, when the negative temperature gradient load is taken, the temperature of the track slab bottom is 0 • C, decreasing linearly to −10 • C at the track slab surface.
Under the action of a negative temperature gradient load, the dead weight is not able to completely restrain the temperature warping deformation of the track slab, resulting in poor contact between the track slab and the mortar cushion, local voids, and uneven stress.Under the action of train load, a "slap" effect will be produced, which will lead to mortar separation and damage.Under the action of a negative temperature gradient, the maximum longitudinal stress of the track slab will occur at the lower surface of both sides, and the maximum transverse stress will occur at the junction of the track slab and the lower surface of the limit stop.When studying the temperature load effect, it is necessary to consider the bonding state of the track slab and the mortar layer, which can be divided into two states: good bonding and poor bonding.Good bonding means that the mortar cushion was constructed using the formwork method, while poor bonding means that the mortar cushion was constructed using the bagging method.The interface transmits the vertical and horizontal temperature force through friction, and the friction coefficient is taken to be 0.3 [18].The elastic moduli (E CA ) of 20, 50, 100, 200, 300, 500, 1000, 5000, 10,000 and 32,500 MPa were taken for the mortar material, respectively.

Mortar Layer under Track Slab with Good Bonding
The warping deformation trend of the track slab under negative temperature load is constrained by the bonding of the lower layer of mortar, and the mortar layer structure will be subject to large warping stress during the subsequent forced deformation.The warping displacement of the track slab is shown in Figure 3.

Mortar Layer under Track Slab with Good Bonding
The warping deformation trend of the track slab under negative temperature load is constrained by the bonding of the lower layer of mortar, and the mortar layer structure will be subject to large warping stress during the subsequent forced deformation.The warping displacement of the track slab is shown in Figure 3.As can be seen in Figure 3, with increasing mortar modulus, the warping displacement of the track slab decreases continuously, and a good constraint effect occurs when the elastic modulus of the mortar is 300 MPa.When the elastic modulus of the mortar increases to 5000 MPa, the displacement of track slab tends to be stable.
The warping stress of the track structure under each mortar elastic modulus is shown in Figure 4.As can be seen from Figure 4, with the increase in the elastic modulus of the mortar, the extreme values of longitudinal and transverse tensile stress and transverse compressive stress at the edge of the track slab under the negative temperature gradient load continue to increase, while the maximum longitudinal compressive stress continues to decrease, such that the structural separation joint often appears at the side.As the limiting effect of the mortar layer on the warping deformation of the track board is gradually As can be seen in Figure 3, with increasing mortar modulus, the warping displacement of the track slab decreases continuously, and a good constraint effect occurs when the elastic modulus of the mortar is 300 MPa.When the elastic modulus of the mortar increases to 5000 MPa, the displacement of track slab tends to be stable.
The warping stress of the track structure under each mortar elastic modulus is shown in Figure 4.

Mortar Layer under Track Slab with Good Bonding
The warping deformation trend of the track slab under negative temperature load is constrained by the bonding of the lower layer of mortar, and the mortar layer structure will be subject to large warping stress during the subsequent forced deformation.The warping displacement of the track slab is shown in Figure 3.As can be seen in Figure 3, with increasing mortar modulus, the warping displacement of the track slab decreases continuously, and a good constraint effect occurs when the elastic modulus of the mortar is 300 MPa.When the elastic modulus of the mortar increases to 5000 MPa, the displacement of track slab tends to be stable.
The warping stress of the track structure under each mortar elastic modulus is shown in Figure 4.As can be seen from Figure 4, with the increase in the elastic modulus of the mortar, the extreme values of longitudinal and transverse tensile stress and transverse compressive stress at the edge of the track slab under the negative temperature gradient load continue to increase, while the maximum longitudinal compressive stress continues to decrease, such that the structural separation joint often appears at the side.As the limiting effect of the mortar layer on the warping deformation of the track board is gradually As can be seen from Figure 4, with the increase in the elastic modulus of the mortar, the extreme values of longitudinal and transverse tensile stress and transverse compressive stress at the edge of the track slab under the negative temperature gradient load continue to increase, while the maximum longitudinal compressive stress continues to decrease, such that the structural separation joint often appears at the side.As the limiting effect of the mortar layer on the warping deformation of the track board is gradually strengthened, the tensile and compressive stresses in the track board increase, which also results in higher compressive and tensile strengths for mortars with high elastic modulus, especially with regard to the bond strength between the track slab and the mortar cushion at the corner of the track slab.

Mortar Layer under Track Slab with Poor Bonding
The warping displacement and stress of the track structure under a negative temperature load are shown in Figure 5.
strengthened, the tensile and compressive stresses in the track board increase, which also results in higher compressive and tensile strengths for mortars with high elastic modulus, especially with regard to the bond strength between the track slab and the mortar cushion at the corner of the track slab.

Mortar Layer under Track Slab with Poor Bonding
The warping displacement and stress of the track structure under a negative temperature load are shown in Figure 5. Compared with the warping state with good bonding, the loss of bonding force is not conducive to the mortar layer restraining the upwarping deformation at the corner of the track slab; therefore, joint damage can easily develop on the four sides.At this time, the support of the mortar to the track slab is limited to the middle of the track slab.With the increase in the elastic modulus of the mortar, the bearing area decreases, and the overall state of the structure is worse than in the case where good bonding was used.The mortar cushion at the corner of the slab is subjected to cycles of high tensile and compressive stress.With increasing numbers of loading actions, the bond between the mortar and the track slab at the corner of the track slab will be destroyed first, meaning that it cannot guarantee the follow-up and restraint ability of the mortar regarding the warping deformation of the track slab.
In addition to the temperature gradient, the overall temperature difference with the lower foundation is also formed during the temperature change in the track slab [19].It is difficult to maintain a permanent bonding state between the bottom of the track slab and the mortar.The ballastless track slab (or track bed slab) unit and the baseplate (or bearing layer) under it should be considered as a separate double-layer structure.The layer can only transmit limited horizontal force through friction.The calculation of warping displacement and stress is recommended in order to be able to take the absence of bonding between the two into consideration.

Subgrade Freeze-Thaw and Frost Heave Effect
The CRTS I slab ballastless track system, as the main track type used for high-speed railways in areas subject to severe cold, is directly exposed to the harsh environment.Under the influence of extreme climates and train loads, a series of deformations appear in the track slab, the cushion under the slab, the baseplate, and other components, such as cracking of the track slab, the track slab cushion, and the baseplate, the track slab Compared with the warping state with good bonding, the loss of bonding force is not conducive to the mortar layer restraining the upwarping deformation at the corner of the track slab; therefore, joint damage can easily develop on the four sides.At this time, the support of the mortar to the track slab is limited to the middle of the track slab.With the increase in the elastic modulus of the mortar, the bearing area decreases, and the overall state of the structure is worse than in the case where good bonding was used.The mortar cushion at the corner of the slab is subjected to cycles of high tensile and compressive stress.With increasing numbers of loading actions, the bond between the mortar and the track slab at the corner of the track slab will be destroyed first, meaning that it cannot guarantee the follow-up and restraint ability of the mortar regarding the warping deformation of the track slab.
In addition to the temperature gradient, the overall temperature difference with the lower foundation is also formed during the temperature change in the track slab [19].It is difficult to maintain a permanent bonding state between the bottom of the track slab and the mortar.The ballastless track slab (or track bed slab) unit and the baseplate (or bearing layer) under it should be considered as a separate double-layer structure.The layer can only transmit limited horizontal force through friction.The calculation of warping displacement and stress is recommended in order to be able to take the absence of bonding between the two into consideration.

Subgrade Freeze-Thaw and Frost Heave Effect
The CRTS I slab ballastless track system, as the main track type used for high-speed railways in areas subject to severe cold, is directly exposed to the harsh environment.Under the influence of extreme climates and train loads, a series of deformations appear in the track slab, the cushion under the slab, the baseplate, and other components, such as cracking of the track slab, the track slab cushion, and the baseplate, the track slab separation, the appearance of voids at the bottom of the slab, and surface peeling of concrete material, and the reduction status of concrete material performance remains unclear.

Freeze-Thaw Cycle Test
With increasing operation time, rain seeps into the cracks and separation joints.Under the action of the freeze-thaw cycle and the dynamic load of the train, the concrete cracks and separation joints continue to evolve and develop.At the same time, the dynamic load of the void part causes the track slab to repeatedly "beat" against the filling layer, further aggravating the damage to the filling layer or the track slab.
The track slab, the mortar layer, and the baseplate in the CRTS I slab ballastless track system are greatly affected by freeze-thaw cycles under environments characterized by seasonal freezing and cold temperatures.Therefore, the materials using in the test include C60 concrete for the track slab, C40 concrete for the baseplate, and cement-emulsified asphalt mortar materials for the filling layers.
C60 concrete material (group HT), C40 concrete material (group LT), and cement emulsified asphalt mortar material were used to produce standard cube test pieces with dimensions (length × width × height) of 150 mm × 150 mm × 150 mm.In addition, by successively pouring C60 concrete and mortar filling materials into the cube mold, a cube specimen (group OT) containing a bonding interface between the two materials was made to simulate the bonding interface between the track slab and the CA mortar layer, as shown in Figure 6.All specimens underwent 28 days of standard curing before testing.[20].The relationship between the peak compressive strength, axial tensile strength, and the number of freeze-thaw cycles in each group of specimens under the action of freeze-thaw cycles is shown in Figure 7.The peak strength is the axial compressive stress under the corresponding limit load, and the splitting tensile strength was converted according to the Code for Design of Concrete Structures (GB50010-2010) [21].It can be seen in Figure 7 that: (1) With the intensification of the freeze-thaw cycle, the material properties of the specimen deteriorated significantly, and the compressive peak strength decreased significantly.For the ballastless track subjected to freeze-thaw cycles, the material performance It can be seen in Figure 7 that: (1) With the intensification of the freeze-thaw cycle, the material properties of the specimen deteriorated significantly, and the compressive peak strength decreased significantly.For the ballastless track subjected to freeze-thaw cycles, the material performance was seriously deteriorated, and the main limiting structure was the mortar layer and concrete baseplate structure.
(2) With the increasing numbers of freeze-thaw cycles, the axial tensile strength of the material decreased significantly.More specifically, the maximum drop of cube specimen (C60 concrete-mortar) with cementation interface before and after freezing and thawing was more than 90%, the separation between the track slab structure and the mortar layer increased, and the tensile properties of C40 concrete structure were significantly affected.
The mechanical performance parameters of ballastless tracks consisting of various structural materials under different numbers of freeze-thaw cycles in indoor test are shown in Table 2. Note: f tk is the axial tensile strength of the corresponding material; "-" indicates no data.

Combined Temperature Load
The rapid indoor freeze-thaw cycle test showed that the durability of the concrete baseplate structure and the mortar layer under repeated freeze-thaw cycles was greatly reduced, and the material performance reduction led to the uneven stress of the track structure.In the simulation model of the CRTS I slab ballastless track, the nature of the contact relationship between track layers is considered to be rigid, with a friction coefficient of 0.5 [13, [22][23][24], and the contact interface between the surface layer of subgrade bed and the baseplate is taken to be the vertical boundary condition.Based on the actual continuous monitoring results of subgrade frost heave on site [25], the classic single-wave cosine curve representing the irregularity of the ballastless track and the frost heave deformation of the high-speed railway subgrade bed was used to simulate the basic waveform of subgrade frost heave, and the temperature load coupled with the frost heave load was then applied to the center of the baseplate (position a) and the expansion joint of the baseplate (position b).
(1) Track slab-CAM layer separation When the temperature gradient load and subgrade frost heave act together, the void and separation state of the track slab and the CAM layer structure is slightly different from that in the case of the single frost heave load, as shown in Figure 8.
and the baseplate is taken to be the vertical boundary condition.Based on the actual continuous monitoring results of subgrade frost heave on site [25], the classic single-wave cosine curve representing the irregularity of the ballastless track and the frost heave deformation of the high-speed railway subgrade bed was used to simulate the basic waveform of subgrade frost heave, and the temperature load coupled with the frost heave load was then applied to the center of the baseplate (position a) and the expansion joint of the baseplate (position b).
(1) Track slab-CAM layer separation When the temperature gradient load and subgrade frost heave act together, the void and separation state of the track slab and the CAM layer structure is slightly different from that in the case of the single frost heave load, as shown in Figure 8.As can be seen in Figure 8, when frost heave acts at position a, the maximum separation under the slab is about 2.6 mm, which occurs at the end of the track slab under the load combination of "negative temperature gradient + frost heave effect".When frost heave acts at position b, the maximum separation under the slab is about 0.8 mm, which occurs at the end of two track slabs under the load combination of "positive temperature gradient + frost heave effect".As can be seen in Figure 8, when frost heave acts at position a, the maximum separation under the slab is about 2.6 mm, which occurs at the end of the track slab under the load combination of "negative temperature gradient + frost heave effect".When frost heave acts at position b, the maximum separation under the slab is about 0.8 mm, which occurs at the end of two track slabs under the load combination of "positive temperature gradient + frost heave effect".
(2) Baseplate-subgrade separation The separation between the baseplate and the surface structure of the subgrade bed is shown in Figure 9. (2) Baseplate-subgrade separation The separation between the baseplate and the surface structure of the subgrade bed is shown in Figure 9.As can be seen from Figure 9, the separation law between the baseplate and the surface layer of the subgrade bed under the combined temperature load is similar to that under the single load of subgrade frost heave.Under the combined load of "overall cooling + frost heave effect", the maximum separation value is 5.9 mm when frost heave acts at position a, and 3.3 mm when frost heave acts at position b.
When frost heave acts at position a, the track structure bears the maximum stress under the load combination of "negative temperature gradient + frost heave effect", and As can be seen from Figure 9, the separation law between the baseplate and the surface layer of the subgrade bed under the combined temperature load is similar to that under the single load of subgrade frost heave.Under the combined load of "overall cooling + frost heave effect", the maximum separation value is 5.9 mm when frost heave acts at position a, and 3.3 mm when frost heave acts at position b.
When frost heave acts at position a, the track structure bears the maximum stress under the load combination of "negative temperature gradient + frost heave effect", and the stress in the middle of the upper surface of the track slab reaches 3.94 MPa.The temperature gradient load only acts on the track slab structure, and has little impact on the baseplate.The baseplate structure is mainly subject to the clamping deformation of frost expansion.The maximum stress under the load combination of "negative temperature gradient + frost heave effect" when frost heave acts at position b is 6.13 MPa.
In conclusion, taking into account the stress of the typical track structure and the interlayer separation, the load combination of "negative temperature gradient + frost heave effect" is the most unfavorable working condition, and the baseplate is a force-limiting structure.

CA Mortar Separation
In this section, the influence of mortar separation conditions and the most unfavorable mortar separation on the stress of the CRTS I slab ballastless track structure is discussed.Considering extreme damage conditions for the transverse through separation, the fastener spacing is taken as the longitudinal unit parting length, and the separation condition is shown in Figure 10.Of these, the frost heave separation condition in the slab refers to the separation of the two ends of the track slab at the center of the frost heave under the working conditions of the slab joint subjected to frost heave; and separation joint refers to the separation joint at the end of the track slab adjacent to the frost heave center.When frost heave acts at the center of the baseplate, there are separation joints at both ends of the track slab, located at the center of the frost heave.When frost heave acts at the expansion joint of the baseplate, there are separation joints at the ends of two adjacent track slabs at the center of the frost heave.
perature gradient load only acts on the track slab structure, and has little impact on the baseplate.The baseplate structure is mainly subject to the clamping deformation of frost expansion.The maximum stress under the load combination of "negative temperature gradient + frost heave effect" when frost heave acts at position b is 6.13 MPa.
In conclusion, taking into account the stress of the typical track structure and the interlayer separation, the load combination of "negative temperature gradient + frost heave effect" is the most unfavorable working condition, and the baseplate is a force-limiting structure.

CA Mortar Separation
In this section, the influence of mortar separation conditions and the most unfavorable mortar separation on the stress of the CRTS I slab ballastless track structure is discussed.Considering extreme damage conditions for the transverse through separation, the fastener spacing is taken as the longitudinal unit parting length, and the separation condition is shown in Figure 10.Of these, the frost heave separation condition in the slab refers to the separation of the two ends of the track slab at the center of the frost heave under the working conditions of the slab joint subjected to frost heave; and separation joint refers to the separation joint at the end of the track slab adjacent to the frost heave center.When frost heave acts at the center of the baseplate, there are separation joints at both ends of the track slab, located at the center of the frost heave.When frost heave acts at the expansion joint of the baseplate, there are separation joints at the ends of two adjacent track slabs at the center of the frost heave.Numerical simulations were performed using longitudinal separation distances of 0 m, 1 × 0.625 m, 2 × 0.625 m and 3 × 0.625 m and vertical separation distances of 0 mm, 2 mm, 6 mm, 10 mm and 15 mm, respectively.Taking frost heave acting at the expansion joint of the baseplate as an example, the extreme stress of each structure in the ballastless track system changes with the combination of separation conditions, as shown in Figure 11.
the track structure increases with the increase in the distance of mortar separation.The most unfavorable combination of separation conditions when frost heave acts at the expansion joint of the baseplate is the longitudinal separation distance of 3 × 0.625 m and the vertical separation distance of 15 mm.In the same way, for frost heave acting at the center of the baseplate, the most unfavorable combination of separation conditions is 3 × 0.625 m longitudinally and 2 mm vertically.For frost heave acting at the expansion joint of the baseplate, it can be seen in Figure 11a that when the fixed separation distance is 3 × 0.625 m, the extreme tensile stress of the track slab, mortar layer and baseplate structure increases with the increase in mortar separation distance, with the most unfavorable separation distace being 15 mm.Accordingly, when the fixed separation is 15 mm, as shown in Figure 11b, the extreme tensile stress of the track structure increases with the increase in the distance of mortar separation.The most unfavorable combination of separation conditions when frost heave acts at the expansion joint of the baseplate is the longitudinal separation distance of 3 × 0.625 m and the vertical separation distance of 15 mm.In the same way, for frost heave acting at the center of the baseplate, the most unfavorable combination of separation conditions is 3 × 0.625 m longitudinally and 2 mm vertically.
The end face of the ballastless track is affected by freezing and thawing, and the performance parameters of the concrete materials are greatly reduced within the range of the freezing and thawing depth [26].The degree of deterioration gradually decreases from the surface to the interior.When the freezing and thawing depth of the concrete is exceeded, the concrete is no longer affected by freezing and thawing.According to the material parameters of the ballastless track structure in Table 2, considering the deterioration of the material following 300 freeze-thaw cycles, we calculated the impact of the most unfavorable mortar separation condition on the ballastless track, and the structural stress state is shown in Figure 12.
The end face of the ballastless track is affected by freezing and thawing, and the performance parameters of the concrete materials are greatly reduced within the range of the freezing and thawing depth [26].The degree of deterioration gradually decreases from the surface to the interior.When the freezing and thawing depth of the concrete is exceeded, the concrete is no longer affected by freezing and thawing.According to the material parameters of the ballastless track structure in Table 2, considering the deterioration of the material following 300 freeze-thaw cycles, we calculated the impact of the most unfavorable mortar separation condition on the ballastless track, and the structural stress state is shown in Figure 12.The structural stress of the baseplate under the freeze-thaw and frost heave load seriously exceeds the limit when separation is occurring under the plate.The mortar layer The structural stress of the baseplate under the freeze-thaw and frost heave load seriously exceeds the limit when separation is occurring under the plate.The mortar layer and the baseplate structure are weak limit structures.The most unfavorable frost heave condition changes to frost heave acting at the expansion joint of the baseplate, and the baseplate is the main load-bearing structure, with a maximum tensile stress of 6.38 MPa.

Reinforcement of Ballastless Track
The length of the concrete ballastless track slab in the horizontal direction is far greater than its vertical thickness, and its vertical deformation under the action of external load is far smaller than its own structural thickness.Therefore, the track slab (or track bed slab, or track bed) and the baseplate (or base, or support layer) can be regarded as an elastic thin plate structure, which is applicable to the plate and shell theory in finite element analysis.The slender rail structure can be regarded as a Euler beam structure that is suitable for the application of beam theory in finite element analysis.Faster systems, elastic damping layers and different lower elastic support foundations can be regarded as elastic structures of equivalent stiffness, for which spring theory in finite element analysis is applicable.In summary, the main structures of the ballastless track system together theoretically constitute an elastic foundation beam-plate-plate.Taking the ballastless track on a bridge as an example, the calculation model is shown in Figure 13.

Theoretical Calculation of the Bending Moment of the Track Structure
The material parameters of the ballastless track system are shown in Table 1.The vertical supporting action of the lower supporting foundation structure (such as the subgrade, bridge and tunnel) is simulated using a continuous and uniform linear spring using different values of supporting stiffness, making the Winkler foundation assumption applicable.When the ballastless track is located in the subgrade section and the thickness of the surface layer of the subgrade bed is 0.5 m, the foundation coefficient is taken to be 76 MPa/m.When the ballastless track is located in the bridge and tunnel section, the foundation coefficient is taken to be 1000 MPa/m [18].
The elastic damping mortar layer structure is simulated using a continuous uniformly distributed linear spring, and the bearing stiffness  of the spring surface of the mortar layer is calculated according to the "elastic modulus of the mortar layer/thickness of the mortar layer".Considering that the supporting effect of the lower baseplate structure has a certain impact on the mortar elasticity, the baseplate elasticity needs to be included.The baseplate spring surface bearing stiffness  is calculated according to the "baseplate elastic modulus/baseplate thickness".Finally, the total surface bearing stiffness

Theoretical Calculation of the Bending Moment of the Track Structure
The material parameters of the ballastless track system are shown in Table 1.The vertical supporting action of the lower supporting foundation structure (such as the subgrade, bridge and tunnel) is simulated using a continuous and uniform linear spring using different values of supporting stiffness, making the Winkler foundation assumption applicable.When the ballastless track is located in the subgrade section and the thickness of the surface layer of the subgrade bed is 0.5 m, the foundation coefficient is taken to be 76 MPa/m.When the ballastless track is located in the bridge and tunnel section, the foundation coefficient is taken to be 1000 MPa/m [18].
The elastic damping mortar layer structure is simulated using a continuous uniformly distributed linear spring, and the bearing stiffness k 1 of the spring surface of the mortar layer is calculated according to the "elastic modulus of the mortar layer/thickness of the mortar layer".Considering that the supporting effect of the lower baseplate structure has a certain impact on the mortar elasticity, the baseplate elasticity needs to be included.The baseplate spring surface bearing stiffness k 2 is calculated according to the "baseplate elastic modulus/baseplate thickness".Finally, the total surface bearing stiffness k of the mortar layer (thin shell cushion layer) is calculated according to the series spring relationship, as shown in Formula (5): where k 1 is the stiffness of the mortar layer (MPa•m −1 ), k 2 is the stiffness of the baseplate (MPa•m −1 ), and k m mortar is the total stiffness of the mortar layer support (MPa•m −1 ).
In order to avoid the calculation not possessing sufficient accuracy, when the spring element is used to support the elastic point of the plate and shell element, the structural mesh size of the shell element of the track slab and the baseplate should be 0.17 m~0.24 m, and the ratio of the long side to the short side of each element should be less than 1.5 [18].

Key Structural Load Parameters
The track structure design using the railway track limit state method, considering the load component coefficient, is based on the calculation of the force and deformation of the track structure under different loads and working conditions, and different combinations of loads are used to obtain the most unfavorable situation, and structural reinforcement design and crack width detection are carried out.In addition to the train load, temperature load, shrinkage deformation of concrete and other load factors mainly considered in the structural design of ballastless tracks in subgrade sections, and the impact of bridge deflection deformation should also be included for the bridge section.
(1) Train load According to the Design Code for High-Speed Railway, the train load values are as follows [27]: 1 Vertical design load: where P d is the vertical design load (kN) and P j is the static wheel load (kN).α is the dynamic load coefficient, which is 3.0 for lines with design speeds of 300 km/h and above, and 2.5 for lines with design speeds of 250 km/h. 2 Vertical fatigue check load: where P f is the vertical design load (kN) and P j is the static wheel load (kN).The value of the train load is shown in Table 3: The actual wheel load of outer rail under superelevation β 2 (quasi-static method) is: The over-superelevation can be calculated using the same principle; the superelevation of the baseplate in the curve section of the ballastless track is 80 mm, and the most unfavorable 90 mm is used for the calculation of under-superelevation/over-superelevation.
(2) Temperature gradient load The stress and bending moment caused by the temperature gradient are calculated as follows: where T g is the negative temperature gradient load, taken to be −50 • C/m, σ is the temperature warping stress, M is the temperature warping moment, α t is the linear expansion coefficient of concrete, taken to be 10 −5 , β h is the temperature gradient plate thickness correction factor, and h, b are the track structure thickness and width, respectively.
(3) Bridge deflection According to the Code for Design of High-speed Railway (TB10621-2014), the limit value of bridge deflection [27,28] should be taken to be as shown in Table 4.The bridge deck bearing stiffness is large, and the rigid foundation method is adopted.The bending moment of the baseplate under the bridge deflection is: where κ max is the maximum curvature of the foundation deformation, δ is the midspan deflection of the bridge (mm), determined according to the limit value of the bridge deflection-to-span ratio, and L is the bridge span (m).

Combination of Load Main Force
Main force combination 1: train design load, used for strength and crack checking.Main force combination 2: train vertical fatigue check load + common temperature gradient + bridge deflection (not considered for subgrade section), used for strength and crack checking.
According to the provisions of Code for Design of Railway Track (Limit State Method) [29,30], the design value of the basic combined bending moment is determined according to Formula (20): where M dk is the standard value of train load bending moment, the partial coefficient γ d of the new high-speed railway is 1.5, M tdk is the standard value of the bending moment under the temperature gradient, the combination coefficient ψ td = 0.5, the partial coefficient γ td = 1.0, M nqk is the standard value of bending moment under beam bending deformation, and the partial coefficient γ nq = 1.0.

Checking the Calculation of Bending Moment Reinforcement
The material properties of steel bars and concrete determine their ability to work together.Due to steel bars and concrete sharing a similar linear expansion coefficient, excessive stress will not be generated due to different environments.There is a good bonding force between steel bars and concrete.By setting spaced ribs onto the surface of the steel bars, the mechanical engagement (i.e., longitudinal bonding force) between concrete and steel bars can be improved.Furthermore, when this is still insufficient to transmit the relative tension between the steel bars and the concrete, the end of the steel bars can be bent 180 degrees with a hook for reinforcement.It is worth mentioning that, due to the alkaline environment provided by calcium hydroxide in concrete, a passivation protective film is formed on the surface of the steel bars, making them less susceptible to corrosion compared to neutral and acidic environments.
The upper and lower layers of HRB335 reinforcement are set in the track slab and baseplate, the minimum reinforcement ratio is 0.15%, and the minimum net thickness of the protective layer of concrete in the ballastless track structure is 40 mm.The allowable value of surface crack width is 0.233 mm, and the allowable stress of the reinforcement is 176 MPa.The bending moments of track slab and baseplate of different supporting foundations (roadbeds, bridges) in straight and curved sections under the most unfavorable freezethaw cycle deterioration conditions were calculated, and the structural reinforcement in cold areas was calculated.When the train load in the subgrade section acts on the center of the slab, the longitudinal bending moment distribution of the structure is as shown in Figure 15.
According to the limit state method of bearing capacity, the combination of structural load bending moment values was performed according to Formula (20), and a summary of the results is shown in Tables 5 and 6.The reinforcement check settings are provided in Table 7.It can be seen from Tables 5 and 6 that under the most unfavorable main force combination in the limit state of bearing capacity, the main structure of the ballastless track slab in the subgrade section, especially the base structure (block type), bears more significant bending moments than the bridge section.Compared with the non-freeze-thaw condition, the maximum increase in the stress of the longitudinal positive bending moment (longitudinal bottom reinforcement) in the superelevation section of the subgrade curve is 513%.
center of the slab, the longitudinal bending moment distribution of the structure is as shown in Figure 15.According to the limit state method of bearing capacity, the combination of structural load bending moment values was performed according to Formula (20), and a summary of the results is shown in Tables 5 and 6.The reinforcement check settings are provided in Table 7.  check and calculate the reinforcement of the track structure.The main conclusions were as follows: (1) When the interface between the track slab and the mortar layer is poorly bonded, the warping deformation of the track structure will increase.The structural stiffness of the mortar layer should be appropriately increased to improve the bearing capacity.
(2) The deterioration of the material properties under freeze-thaw cycles is serious, the phenomenon of separation between the track slab structure and the mortar layer intensifies, and the tensile properties of the baseplate structure are significantly affected.The maximum tensile stress of the baseplate under the coupling action of negative temperature gradient and foundation frost heave load exceeds 6 MPa.
(3) The mortar layer and the baseplate structure are weak limit structures when there are gaps under the track slab.The most unfavorable foundation deformation condition is frost heave acting at the expansion joint of the baseplate, which is the main load-bearing structure.
(4) Under the effect of freeze-thaw deterioration, the original reinforcement design of the substructure structure does not meet the requirements of structural cracks and the yield stress of the reinforcement.It is necessary to increase the number of reinforcement layers, or increase the diameter of the reinforcement, and it is necessary to redesign the structural reinforcement.

Figure 2 .
Figure 2. Time-history of vertical temperature gradient load on a track slab in Harbin.

Figure 2 .
Figure 2. Time-history of vertical temperature gradient load on a track slab in Harbin.

Figure 5 .
Figure 5. Warpage characteristics of structure (without bonding): (a) displacement of track structures; (b) stress of track structures.

Figure 5 .
Figure 5. Warpage characteristics of structure (without bonding): (a) displacement of track structures; (b) stress of track structures.

Figure 6 .
Figure 6.Schematic diagram of specimen preparation.According to Standard for Test Methods of Long-term Performance and Durability of Ordinary Concrete (GB/T50082-2009), the frost resistance grade of concrete is determined on the basis of multiple groups of parallel freeze-thaw cycles, with number of cycles N of 50, 100, 150, 200, 250 and 300, respectively.According to the statistical analysis, the corresponding numbers of outdoor freeze-thaw years are 0, 7.7, 25.4, 23.1, 30.8, 38.5 and 46.2 years[20].The relationship between the peak compressive strength, axial tensile strength, and the number of freeze-thaw cycles in each group of specimens under the action of freeze-thaw cycles is shown in Figure7.The peak strength is the axial compressive stress under the corresponding limit load, and the splitting tensile strength was converted according to the Code for Design of Concrete Structures (GB50010-2010)[21].

Figure 8 .
Figure 8.Effect of temperature combined load on track slab-CAM layer separation: (a) position a; (b) position b.

Figure 8 .
Figure 8.Effect of temperature combined load on track slab-CAM layer separation: (a) position a; (b) position b.

Figure 9 .
Figure 9.Effect of temperature combined load on baseplate-subgrade separation: (a) position a; (b) position b.

Figure 9 .
Figure 9.Effect of temperature combined load on baseplate-subgrade separation: (a) position a; (b) position b.

Figure 10 .Figure 10 .
Figure 10.Schematic diagram of CAM separation: (a) frost heave acting at the center of the baseplate; (b) frost heave acting at the expansion joint of the baseplate.

Figure 13 .
Figure 13.Elastic beam-plate of ballastless track slab on a bridge.

Table 1 .
Structural parameters of the ballastless track.

Table 1 .
Structural parameters of the ballastless track.

Table 2 .
Mechanical parameters of materials under different freeze-thaw cycles.

Table 4 .
Vertical deflection limit of the bridge body.

Table 5 .
Bending moment of ballastless track structure in the subgrade section.

Table 6 .
Bending moment of ballastless track structure in bridge section.