Advancements in Doping Strategies for Enhanced Photocatalysts and Adsorbents in Environmental Remediation

: Environmental pollution poses a pressing global challenge, demanding innovative solutions for effective pollutant removal. Photocatalysts, particularly titanium dioxide (TiO 2 ), are renowned for their catalytic prowess; however, they often require ultraviolet light for activation. Researchers had turned to doping with metals and non-metals to extend their utility into the visible spectrum. While this approach shows promise, it also presents challenges such as material stability and dopant leaching. Co-doping, involving both metals and non-metals, has emerged as a viable strategy to mitigate these limitations. Inthe ﬁeldof adsorbents, carbon-based materials doped with nitrogen are gaining attention for their improved adsorption capabilities and CO 2 /N 2 selectivity. Nitrogen doping enhances surface area and fosters interactions between acidic CO 2 molecules and basic nitrogen functionalities. The optimal combination of an ultramicroporous surface area and speciﬁc nitrogen functional groups is key to achievehigh CO 2 uptake values and selectivity. The integration of photocatalysis and adsorption processes in doped materials has shown synergistic pollutant removal efﬁciency. Various synthesis methods, including sol–gel, co-precipitation, and hydrothermal approaches had been employed to create hybrid units of doped photocatalysts and adsorbents. While progress has been made in enhancing the performance of doped materials at the laboratory scale, challenges persist in transitioning these technologies to large-scale industrial applications. Rigorous studies are needed to investigate the impact of doping on material structure and stability, optimize process parameters, and assess performance in real-world industrial reactors. These advancements are promising foraddressing environmental pollution challenges, promoting sustainability, and paving the way for a cleaner and healthier future. This manuscript provides a comprehensive overview of recent developments in doping strategies for photocatalysts and adsorbents, offering insights into the potential of these materials to revolutionize environmental remediation technologies.


Introduction
Metal oxide-based semiconductors play a pivotal role as photocatalysts, offering a versatile solution for various environmental and energy-related challenges.However, the intrinsic properties of these materials, such as their wide bandgap, had traditionally confined their utility to the ultraviolet (UV) region, limiting their efficiency in utilizing visible light.To bridge this gap, diverse strategies had been developed to harness the potential of metal oxide photocatalysts in the visible wavelength range to enhance photostability, environmental compatibility, and overall photoresponse efficiency [1,2].
One of the most promising techniques in this endeavour is the incorporation of nanoscale metal oxide particles, which significantly amplify the surface-to-volume ratio, thereby augmenting the available active sites for catalytic reactions.Among these strategies, the deliberate doping of photocatalysts with nanoparticles emerges as a highly effective approach for enhancing photoresponse efficiency.In this context, doping refers to the deliberate introduction of impurities, whether cationic or anionic, into a material to induce specific alterations in its properties.This technique had demonstrated remarkable potential in modifying the electronic structure of photocatalysts, consequently reducing their bandgap and extending their photoactivity into the visible spectrum [3].
Transition metals, including iron, manganese, copper, and nickel, and their respective oxides had been favoured choices for doping photocatalysts like TiO 2 .This process had proven to be instrumental in enhancing photocatalytic efficiency under visible light irradiation by narrowing the bandgap of these catalysts [4].However, while single-doping of TiO 2 nanocatalysts had shown promising results in improving photocatalytic efficiency, the co-doping approach with multiple transition metals can sometimes yield unfavourable outcomes due to the intricate interplay between electron-hole recombination and nanoparticle shielding effects.
In recent years, the utilization of non-metal dopants, such as nitrogen, carbon, fluorine, sulphur, and iodine, had gained prominence as an alternative doping strategy.These non-metals offer advantages, including the enhanced thermal stability of the resulting catalyst and improved performance in visible light, primarily attributed to a significant reduction in the bandgap and the suppression of electron-hole recombination processes [5].
Concurrently, adsorbents for dye removal and water treatment had witnessed a surge in the utilization of nanomaterials.These materials, encompassing polymers, carbon nanotubes, carbon nanoparticles, metals, and metal oxides, offer a substantial surface area, short intraparticle diffusion distances, multiple sorption sites, and tuneable pore sizes, making them highly effective adsorbents.Recent advancements had seen nano sorbents modifiedthrough techniques such as coating and doping to enhance their adsorption capacities [6,7].
Specifically, the introduction of alkali dopants and rare earth materials such as doping agents has proven efficacious in tailoring the adsorption properties of nanosorbents, thereby enhancing their performance.
In this paper, we embark on a comprehensive exploration of the intricate process of doping adsorbents and photocatalysts.Our objectives are as follows: To provide an extensive review of the methodologies employed in the synthesis of doped photocatalysts and adsorbents, encompassing the utilization of metals, metal oxides, and non-metals.To examine the diverse applications of doped systems, shedding light on the substantial efficiency improvements realized in doped catalysts and adsorbents when compared to their undoped counterparts.To scrutinize the influence of dopants on the performance of integrated adsorbentphotocatalytic units, uncovering the synergistic effects and benefits conferred by doping.To identify and discuss the existing limitations inherent to doping processes and propose potential strategies to overcome these limitations.
With this comprehensive overview, we aim to contribute to the broader understanding of the pivotal role played by doping in advancing the field of environmental remediation and sustainable technologies.

Doping of Photocatalysts with Nanoparticles
A series of key steps govern the process of photocatalysis.It commences with the absorption of photons by the catalyst, triggering the excitation of electrons, which then migrate from the valence to the conduction band.This results in the formation of electron-hole pairs, which were subsequently transported to the surface of the semiconductor catalyst.Once on the surface, a sequence of oxidation and reduction reactions takes place, generating highly reactive oxidizing species that react with adsorbed impurities, effectively decomposing them [8].
However, a significant challenge arises when using metal oxide photocatalysts like titanium dioxide (TiO 2 ).These materials possess a relatively wide bandgap of 3.2 eV, requiring ultraviolet (UV) radiation for activation.Unfortunately, UV radiation accounts for only a small fraction (5%) of the total solar energy, while visible radiation comprises a substantial portion (45%).Various strategies had been explored to harness the more abundant visible light, and one promising avenue involves doping photocatalysts with metal and non-metal nanoparticles.This approach offers several advantages, including enhanced light absorption, improved efficiency in separating and transferring charges, and heightened photocatalytic activity [9].
Nanoparticle doping also provides an opportunity to exert precise control over critical parameters such as particle size, shape, and distribution within the photocatalyst matrix.Additionally, it significantly increases the surface area-to-volume ratio, providing more active sites for catalytic reactions and thus enhancing overall catalytic activity [9].
The effects of nanoparticle doping are vividly illustrated in Figure 1, where it is evident that this process reduces the band gap of the photocatalyst and improves its performance.Typically, the stages involved in the nanoparticle doping of photocatalysts include the synthesis of nanoparticle dopants and their subsequent incorporation into the photocatalyst matrix.Transition metals, with their unfilled d-electron structure, play a pivotal role in facilitating the transfer of electrons from the 3d orbital of the dopant material to the conduction band of TiO 2 .This enables the accommodation of a greater number of photogenerated electrons and holes, effectively shifting TiO 2 s response towards visible wavelengths [8][9][10].

Doping with Metal and Metal Oxides
Doping with metals and metal oxides is a pivotal strategy used in photocatalysis to boost the performance of photocatalytic materials like titanium dioxide (TiO2).This technique involves introducing specific types of metals or their oxides into the photocatalyst's structure, fundamentally altering its physical and chemical properties [12].[11]).

Doping with Metal and Metal Oxides
Doping with metals and metal oxides is a pivotal strategy used in photocatalysis to boost the performance of photocatalytic materials like titanium dioxide (TiO 2 ).This technique involves introducing specific types of metals or their oxides into the photocatalyst's structure, fundamentally altering its physical and chemical properties [12].These modifications often enhance light absorption, charge separation, and overall photocatalytic activity.
A variety of techniques were employed to introduce these metal dopants into photocatalytic materials.

Sol-Gel Method
The sol-gel technique is a widely adopted approach.It starts with the creation of a homogeneous solution containing metal precursors.This solution undergoes a process called condensation, leading to the formation of a gel.Subsequent drying removes the solvent, yielding metal-doped nanoparticles [13][14][15][16][17][18][19].For example, Neodymium (Nd) doping in TiO 2 nanoparticles was accomplished by mixing solutions of Neodymium (III) acetate dehydrate in isopropyl alcohol with a titanium isopropoxide solution in alcohol.The addition of acetic acid and pH adjustment completed the hydrolysis process, resulting in transparent sols.After aging, thorough washing, centrifugation, drying, and annealing, Nd-doped TiO 2 nanoparticles were produced.This process enhances the photocatalytic removal of dyes and pollutants under solar light [19].Similar methods hadbeen applied to Neodymium doping with variations [17].Rare earth elements other than Neodymiumnamely, Lanthanum (La), Europium (Eu), and Gadolinium (Gd)-had also been used for doping TiO 2 to improve the photocatalytic performance of TiO 2 , and the doped photocatalysts prepared bythesol-gel method were successfully applied for pollutant/dye removal [20,21].Apart from TiO 2 , rare earth element-doped ZnO nanoparticles synthesized by the sol-gel method had been used extensively in dye degradation [22][23][24][25].In recent studies, the sol-gel method was employed to synthesize nickel-doped ZnO nanoparticles to be used as photocatalysts with 94% dye degradation ability [26] and to prepare ceriumdoped ZnO: TiO 2 nanocomposite-based photocatalysts for dye degradation and antibiotic removal [27].Europium(Eu)-doped nanocomposites of ZnO-SnO 2 , synthesized by the sol-gel method, exhibited enhanced dye degradation efficiency due to the formation of Z-scheme heterojunctions in the presence of the Eu ions [28].
The synergistic enhancement of CO 2 photo-reduction and selectivity towards CH 4 using bismuth-doped TiO 2 had been observed by earlier researchers [29].A bismuth-based TiO 2 nanocatalyst was prepared by the sol-gel method.Furthermore, photo-deposited platinum on the catalyst surface had been effectively used as an electron-trapping agent with the ability to extract the electrons trapped on the surface of TiO 2 in a few picoseconds.TiO 2 photocatalysts doped with iron [30] and co-doped with manganese and boron [31] had been synthesized with enhanced structural and photocatalytic properties using the sol-gel method for dye removal.Silver-doped TiO 2 nanoparticles had been widely used as photocatalysts due to the following reasons: firstly, their enhanced photocatalytic efficiency in the visible light induced by the surface plasmon resonance effect; secondly, the creation of a Schottky barrier at the TiO 2 interface to trap electrons from the conduction band and transfer them to oxygen, thereby preventing electron-hole recombination; and thirdly, the enhanced antibacterial properties of silver, which were another essential feature for its selection as a doping agent [8].Several techniques had been used to synthesize silver-doped TiO 2 nanoparticles, including sol-gel, hydro/solvothermal, photo-deposition, chemical reduction, impregnation, and co-precipitation.The sol-gel route had been used to prepare silver-doped TiO 2 nanopowderviadropwise addition of an aqueous solution of silver nitrate to a mixture of TiO 2 in acetic acid, resulting in gel formation.In one instance, the gel was air dried and annealed to yield the photocatalyst in nanopowder form to be employed for dye removal [32].In another instance, silver-loaded TiO 2 -ZnO thin films were prepared on glass substrates using thesol-gel method.A TiO 2 precursor solution was prepared by mixing titanium isopropoxide, acetic acid, propanol, and water.ZnO sol was subjected to 48 h of aging before mixing with the TiO 2 sol, and doping was achieved by adding a silver nitrate solution of different concentrations to the mixed sol.The pretreated glass substrates were dipped in the silver-doped sols, dried, and treated thermally [33].
In a recent study, cerium-doped ZnO/TiO 2 nanospheres were synthesized for a photocatalytic degradation of dye and levofloxacin in visible light where ZnO and TiO 2 sols were initially mixed, followed by addingtheprecursor solution of the dopant cerium and stirring for 3 h.The addition of NaOH solution to the doped solution was followed by centrifugation, washing, drying, grinding the precipitate, and sintering them at 500 • C for 3h to yield the final photocatalyst [27].

Solvo/Hydrothermal Treatment
Hydrothermal methods were employed to synthesize photocatalysts under hightemperature and high-pressure conditions in an aqueous environment.This technique allows for precise control over particle size and structure.Researchers used hydrothermal treatment to prepare various doped photocatalysts, including Nd-doped TiO 2 [20,21].Researchers attempted to modify TiO 2 by adsorbing photosensitive molecules, such as hetero-poly(phosphotungstic acid) (HPA), on its surface.Nd-doped TiO 2 was prepared through hydrothermal treatment by adding the dopant neodymium salt to a titanium isopropoxide solution, followed by distilled water to induce precipitate formation [16].Another recent study used hydrothermal treatment to prepare copper-doped mesoporous TiO 2 .A solution of polyvinyl alcohol in boiling water was mixed with titanium isopropoxide in acetic acid, followed by ultrasonication and calcination.Copper nanoparticles of different weight percentages were added to prepare the doped photocatalyst [34].Magnesiumdoped SnO 2 nanoparticles with enhanced photocatalytic activity and catalyst reusability were prepared using a hydrothermal technique [35].
This versatile one-step hydrothermal method creates nanocomposites of metal-doped titanium oxide-graphene oxide.It involves mixing graphene oxide with metal and titanium precursors and subjecting the mixture to hydrothermal treatment.This results in composite powders containing various metal dopants, such as silver, copper, and palladium [36].A one-step hydrothermal method had recently been used for preparing iron-doped Bi 2 O 2 CO 3 photocatalysts with FeOx nanoparticles deposited on the photocatalyst.Here, a combination of doping and co-catalyst addition was employed to enhance the photocatalytic degradation ability of Bi 2 O 2 CO 3 to a maximum value in visible range [37].

Pulsed Laser Ablation in Liquid (PLAL)
PLAL technology offers a novel approach to producing metal-doped nanoparticles.It involves the laser-induced ablation of a target material submerged in a liquid medium.The poor solubility of dopants in the photocatalyst matrix was a major factor hindering the achievement of high photocatalytic activity and can be overcome using plasma-assisted laser ablation techniques.This method had been utilized to generate Nd-doped ZnO nanoparticles [38,39], allowing for precise control over dopant incorporation.In the double pulse laser ablation technique, a zinc plate serving as the target was added to the neodymium salt solution, followed by the irradiation of the target with a pulsed laser for 10 nanoseconds, resulting in the formation of plasma near the target.The doped colloidal nanoparticles were further subjected to laser modifications [38].In another instance, the doping efficiency of the solvent during a laser ablation of Gd 2 O 3 with Europium was tested, where the doping concentration was found to be proportional to the initial concentration of the dopant in an aqueous solution over two orders of magnitude.The mechanism of laser-ablated doping was revealed [39].

Flame Spray Pyrolysis
Flame spray pyrolysis(FSP) is another method employed for preparing metal oxidedoped photocatalysts.In this process, precursors weredissolved in alcohol and introduced into a reactor.The combustion of methane and oxygen generates a flame, evaporating the precursors and forming doped nanoparticles.This technique produces uniform and well-defined nanoparticles, such as ZnO nanoparticles doped with WO 3 [40].In another instance, single nozzle-based FSP had been used to synthesise lanthanum-doped perovskite SrTiO 3 for hydrogen production.In contrast, double nozzle FSP was used for creating a heterojunction between CuO and lanthanum-doped SrTiO 3 for the selective photocatalytic production of CH 4 from H 2 O/CH 3 OH.In the dual nozzle FSP, two asymmetrically placed FSP nozzles operate in tandem-the left one used for producing Lanthanum-doped SrTiO 3 nanomaterial and the right one for CuO nanoparticles.This was followed by depositing the nanoparticles and binder on a glass microfiber filter with the aid of a vacuum pump and scrubbing the nanoparticles from the filter [41].

Chemical Precipitation and Co-Precipitation
The synthesis of tin-doped zinc nanoparticles withthe chemical precipitation method was carried out by adding potassium hydroxide solution dropwise to anaqueous solution of tin chloride dihydrate and zinc acetate dihydrate.The purification of white precipitate followed by air-drying at 100 • C for 6 h and annealing at 300 • C for 3 h in a muffle furnace resulted in the final product [42].In another instance, the co-precipitation method synthesised iron-doped ZnO nanoparticles [43].Here, zinc acetate dihydrate, the precursor of ZnO nanoparticles, and ferric chloride, the precursor of iron, was dissolved in water, followed by the addition of NaOH solution to maintain an alkaline pH.The mixture was heated at 85 • C for 2 h, cooled, and kept for 24 h.The precipitate obtained was washed, dried, and annealed at 400 • C to obtainthe final product.Recent studies reported green synthesis methods for synthesizing ZnO/WO 3 nanocomposites for the photocatalytic removal of organic pollutants [44].A comparative study was conducted between nickeldoped Co 3 O 4 and bimetal-doped Co 3 O 4 photocatalysts to identify the best combination of dopants and photocatalysts during visible light dye degradation.The two dopant metals other than nickel were copper and cadmium.The Cadmium-nickel bi-doped photocatalyst exhibited the greatest photocatalytic activity of 93% [45].
Figure 2 presents schematic diagrams illustrating the synthesis of metal-doped TiO 2 through different routes, showcasing the adaptability and potential of these methods.Metal and metal oxide doping continue to be at the forefront of research in the field of photocatalysis, driving innovations and improvements in performance across a wide range of applications.Recently, a combination of two or more techniques had been used to prepare photocatalysts with several enhanced properties, including optical, photocatalytic properties, UV-induced wettability, and self-cleaning effects.A recent study used a combination of sol-gel and spin coating methods fordoping copper in zinc oxide thin films.The precursor solutions for zinc and copper were dissolved in a mixture of solvent and stabilizer and stirred at 60 • C. The coating sol, thus obtained, was kept in the dark for a day and spin-coated at 2000 rpm on a glass substrate for 30 s.The spin coating was followed by drying at 180 • C, and the processes of spin coating and drying were repeated multiple times.Annealing was performed at 500 • C for 2 h, forming copper-doped zinc oxide film with enhanced photocatalytic, super-hydrophilic, and self-cleaning properties [48].
Copper-doped nickel oxide nanoparticles with a new morphology and modified band gap were synthesized by combining co-precipitation and calcination [49].The calcination temperatures affected the morphologies of the doped photocatalyst and surface areas.In a recent study, tin-doped TiO 2 nanoparticles were synthesized by a sol-gel route followed by calcination at various temperatures from 450-750 • C. The optimum formulations of tin-doped TiO 2 were screen printed and annealed at 500 • C. A dispersion of the synthesized nanoparticles in 2-propanol, α-terpeniol, and ethyl cellulose was prepared, followed by the incorporation of additives, and the mixture was homogenized to produce a paste which was screen printed on a glass slide using a hard square edge polyurethane squeegee and 400 meshcount screens [50] A green synthesis method involving a microwave-assisted combustion technique with Tamarindus indica seed extract as fuel was used to synthesise Ni-doped magnesium ferrite nanoparticles with a spinel cubic structure for use as visible range photocatalysts for dye degradation [51].The sol-gel auto-combustion method had been used for synthesizing metal-doped nano cubic spinel ferrite-based photocatalysts for wastewater treatment [52,53] Considerable enhancement of the photocatalytic activity of TiO 2 during hydrogen production hadbeen achieved by using two-dimensional transition metal-based carbonitrides, also known as MXenes, as cocatalysts.MXene offers the unique advantage of possessing a layered structure, excellent conductivity, excellent exposure to metallic sites, and tuneable electronic structures.Electrostatic self-assembly and photoreduction processes were used to prepare the Ag/Ti 3 C 2 /TiO 2 nanocomposites for photocatalytic hydrogen production.The scheme for the synthesis process is illustrated in Figure 3 [54].The solar-driven photocatalytic reduction of CO 2 to CH 4 and CO is a newly evolved, promising strategy for addressing energy challenges and environmental concerns.In this respect, metal-organic frameworks had emerged as promising photocatalytic materials, with their organic ligands serving as light-harvesting centres, activating the metal cluster nodes.However, MOFs suffer from limitations-namely, poor charge separation, low conductivity values and poor migration efficiency.In a recent study, the drawbacks were overcome by synthesising a durable hybrid cobalt-based MOF/Cu 2 O composite containing a p-n heterojunction for carrying out solar-driven CO 2 photoreduction with increased efficiency.An ultrasonicated aqueous solution of MOF was mixed with CuCl 2 2H 2 O and NaOH solutions, followed by a dropwise addition of ascorbic acid solution.The resulting suspension was centrifuged and vacuumdried to yield a fine composite powder [55].In another study, the facile hydrothermal method was used to fabricate azobenzene tetracarboxylic acid-based MOF for the effective photocatalytic reduction ofCO 2 to CH 4 , along with high CH 4 selectivity [56].The solvothermal method was recently used to incorporate a rhodamine dye molecule into a zirconium-based MOF framework to fabricate a dyesensitized photocatalyst for CO 2 reduction.Anchoring the dye molecule into MOF-based semiconductors expands the light absorption range of the photocatalyst and initiates the transfer of electrons from the excited dye molecule to the MOF.The composite was prepared viareaction of the dye and the MOF in water at 120 • C for 24 h.After cooling to room temperature, precipitates were centrifuged and washed thoroughly to remove additional dyes, followed by vacuum drying [57].
The construction of a heterojunction ensures enhanced carrier mobility and improved the photocatalytic performance of the catalysts.However, interface defects and poor energy levels can lead to interface recombination, leading to a loss in photocatalytic performance.Reduction in interfacial recombination had been carried out by adjusting the band alignment in the existing photocatalyst.The cliff-like conduction band offset (CBO) in CuSbS 2 (CAS)/ZnO was modified by coupling another material, CdS, to form spike-like CBO, resulting in a reduced interface combination rate and increased photocatalytic efficiency.The CAS-ZnO-CdS heterojunction prepared by the microwave-assisted method produced a hydrogen evolution of 140.45 µmol/g after 4 h of illumination [58].A combination of solvothermal and electrospinning technology was used for preparing CuBi 2 O 4 -Bi 2 WO 6 nanofibres with Z scheme heterojunction with a 90% degradation efficiency of tetracycline hydrochloride [59].
Single-atom catalysts performed excellently due to the uniform adsorption of reactants/intermediates on each active site and avoidance ofmultiple adsorptions.They were highly selective for reactions-namely, hydrogenation, electrocatalysis, and oxidationand exhibit high activity.Nitrogen-doped graphene (NG) material with N as the Lewis base binds strongly to the Lewis acid, namely, single-atom metal centre.It provided a stable, coordinated environment for the single metal atom.A recent study used a precursor dilution strategy to prepare a copper/nickel dispersed poly(tetraphenyl porphyrin) through Friedel Crafts alkylation, and it was deposited on modified TiO 2 microspheres.The atomically dispersed Cu-N 4 and Ni-N 4 complexed with NG were subsequently synthesized viacalcination at 800 • C [60].The desulphurization of dibenzothiophene using the bimetallic single-atom catalyst was 100%, with a total metal loading of 0.1 wt% for both metals.A narrow band gap semiconductor (~1.5 eV), CuInS 2 , had been used in photocatalytic hydrogen evolution, pollutant degradation, and CO 2 reduction due to its strong response under visible light and excellent stability.A combination of hydrothermal and calcination methods had been used for fabricating a boron-doped TiO 2 /CuInS 2 Z scheme heterojunction yielding 21.39µmol/g/h of CO and 4.83 µmol/g/h of CH 4 during a photocatalytic CO 2 reduction with no significant reduction in yield after threecycles.The yield of gases was 10 and 13 times higher than the standalone TiO 2 and boron-doped TiO 2 .The oxygen-rich species and Ti 3+ introduced by boron doping acted as electron traps for preventing the recombination of the photogenerated carriers, and heterojunction hastened the separation of carriers, retainedelectrons and holes, and improved visible light absorption [61].The combination of hydrothermal and calcination methods used for the synthesis of MXene-based catalysts is demonstrated in Figure 3.

Photocatalysts Doped with Non-Metals
Non-metal doping had gained substantial attention in photocatalysis due to its potential advantages over metal doping.Non-metal elements-such as carbon, nitrogen, and sulphur-offer unique opportunities for modifying photocatalytic materials without some of the drawbacks associated with metal dopants, such as increased thermal instability, poor dopant solubility, secondary phase formation, and phase transformations [47].This section explores various non-metal doping strategies and their implications for enhancing photocatalytic performance.
Carbon doping of TiO 2 nanoparticles had been explored as an approach to extend their photocatalytic activity into the visible light range.This was typically achieved using the sol-gel method, incorporating a stabilizing agent and a titanium tetra-isopropoxide precursor.Interactions amongthe doped carbon, titanium, and oxygen atoms within the TiO 2 lattice lead to a reduction in the band gap energy.By adjusting the concentrations of the stabilizing agent and the carbon dopant, researchers finely tuned the band gap energy, thereby facilitating photocatalytic reactions in the visible light spectrum.Additionally, vari-ations in dopant and stabilizing agent concentrations allow for favourable microstructure modifications, further optimizing photocatalytic performance.
Ionic liquids had proven to be effective sources of co-dopants, including carbon and nitrogen, for mesoporous titania nanoparticles.Co-doping with carbon and nitrogen can be achieved by introducing appropriate amounts of ionic liquid into solutions containing titanium isopropoxide in ethanol.This process involves evaporation-assisted self-assembly and subsequent calcination [62].Alternatively, several mechanical and chemical methods, such as ball milling, sol-gel synthesis, sputtering, solvothermal and hydrothermal processes, and the direct hydrolysis of salts, hadbeen employed to introduce nitrogen into the titania lattice.Nitrogen sources for doping include urea, thiourea, nitrogen dioxide, ammonia, and triethylamine [63].
One innovative application of non-metal doping involves the development of nanocomposites composed of TiO 2 and reduced graphene oxide doped with nitrogen.These nanocomposites hadshown excellent resultsin carbon dioxide (CO 2 ) photoreduction.The synthesis of such nanocomposites typically involves a urea-assisted single-step hydrothermal method.In this process, graphene oxide wasdispersed in an aqueous ethanol solution, followed by the addition of urea and TiO 2 .The mixture was subjected to high-temperature hydrothermal treatment, forming solid nanocomposites with exceptional photocatalytic properties for CO 2 conversion [64].The solvothermal synthesis of nitrogen-doped TiO 2 and Fe 2 O 3 nanocomposites yielded photocatalysts with enhanced activity owing to the formation of a heterojunction between nitrogen-doped TiO 2 and Fe 2 O 3 .The nanocomposite absorbed light at a higher rate compared to the TiO 2 alone and resulted in the nearly complete oxidation of methanol [65] Solvent-based multi-doping strategies had also been explored, aiming to enhance the optoelectronic properties of TiO 2 .These strategies involve doping TiO 2 with non-metals (nitrogen, carbon, and sulphur) and metals (e.g., iron) using the sol-gel synthesis method.Titanium isopropoxidewas typically added to an aqueous solution containing thiourea and iron chloride.Stirring the solution for an extended period, followed by aging, air-drying, grinding, and calcination yielded multi-doped TiO 2 materials with tailored properties [66].
Another noteworthy approach incorporated fluorine-doped graphene as a supporting matrix for the synthesis of gadolinium orthovanadate nanoparticle-based photocatalysts.In this process, fluorine-doped graphene was prepared by mixing graphene and sodium fluoride in water, followed by sonication and shaking.The resulting fluorine-doped graphene was then dispersed in water, and gadolinium nitrate and polyethylene glycol wereadded to create a homogeneous dispersion of the photocatalyst on the support.This approach offered intriguing possibilities for designing advanced photocatalytic materials [67].
Figure 4 provides a comprehensive visual representation of the intricate synthesis process involved in creating nitrogen-doped mesoporous TiO 2 (TiO 2 -N), a highly advanced photocatalytic material with promising applications.The illustration delineates critical elements of the synthesis, starting byusing various chemical reagents crucial for introducing nitrogen dopants into the TiO 2 structure.The depiction of a controlled reaction vessel underscores the importance of maintaining precise conditions during synthesis.The source of nitrogen dopants, likely involving ammonia or similar compounds, is highlighted, emphasizing its role in achieving successful nitrogen doping.Additionally, the figure elucidates the mesoporous structure of TiO 2 , essential for maximizing the material's surface area, thereby enhancing photocatalytic activity.The heart of the illustration lies in illustrating how nitrogen atoms wereintegrated into the TiO 2 lattice, a fundamental alteration that extended the material's photocatalytic capabilities into the visible light spectrum.Overall, Figure 4 offers valuable insights into synthesising nitrogen-doped mesoporous TiO 2 .It highlights controlled chemical reactions as the key to its advanced properties, particularly its enhanced ability to harness solar energy and address environmental challenges through advanced photocatalysis.This section underscores the diverse strategies employed to introduce non-metal dopants into photocatalytic materials, highlighting their potential to enhance performance and broaden the scope of photocatalysis.
Nitrogen-doped TiO 2 exhibited boosted visible light absorption due to the shifting of 2p orbital levels.In a recent study, Ag/AgCl/N-doped TiO 2 photocatalysts hadbeen synthesized for achieving high ammonia conversion during photocatalytic ammonia oxidation and significant N 2 selectivity compared to NOx due to a change in the reaction pathway [70].A combined sol-gel and photo deposition method was used for preparing the catalyst.In another instance, the stability of N-doped carbon material in peroxydisulphatebased Fenton reactions was enhanced by synthesizing N-doped carbon spheres with TiO 2 nanoparticles supported on the inner surface of the hollow spheres [71].Direct electron transfer (DET)-based non-radical activation of persulfates utilized the N-doped carbon material as electron transport conductors and reduced the persulfates without being oxidized.To achieve this, N-doped carbon was deposited on TiO 2 nanoparticle-wrapped SiO 2 viachemical vapour deposition followed by alkali etching, which resulted in the generation of the TiO 2 -incorporated hollow N-doped carbon spheres.

Structural Modifications of Doped Photocatalysts
The effects of metal doping on structural and morphological characteristics had been investigated viacharacterization of the doped and undoped samples using standard characterization techniques-namely, SEM, XRD, UV-Vis spectroscopy, FTIR and energy dispersive X-ray spectroscopy.In one of the studies on nickel-doped ZnO, the diffraction peaks obtained in the sample were sharper than in the undoped one, indicating the strong crystalline nature of the doped sample, which increased with dopant concentration and pH.However, the hexagonal wurtzite structure of the original undoped photocatalyst remained unchanged in the doped one [26].However, an increase in dopant concentration beyond a critical concentration increased the agglomeration of the particles with a subsequent increase in the energy band gap, which was undesirable.Similarly, in pure TiO 2 and silver-doped TiO 2 , the main phase was identified as anatase with no alteration in the crystal structure in the doped sample.The grain sizes calculated using the Debye-Scherrer formula were between 16-18 nm in undoped and doped samples, indicating the negligible impact of doping on grain sizes [32].The Debye-Scherrer equation is given as Here, D represents the grain size, λ is the wavelength of the Cu-Kα line, β is the full width at half maxima (FWHM), and θ is the Bragg angle.Furthermore, the optical band gap energy was calculated using the Tauc equation as follows: Here, K is a constant; hν is the energy of the incident photon, e.g., the band gap energy for indirect transitions; and α is the absorption coefficient.It was observed that E g decreased with the increasing concentration of silver, indicating a delay in the recombination of the electron-hole pair, resulting in improvement in photocatalytic activity.In another instance, a nickel-and zinc-doped barium hexaferrite photocatalyst was fabricated using themicroemulsion route, and XRD analysis confirmed a hexagonal structure with zinc and nickel ions substituting barium and iron cations at the tetrahedral and octahedral positions.An increase in dopant concentration reduced the band gap energy, indicating a beneficial effect of doping on the photocatalytic activity.This was further confirmed by the decrease in intensity of the peak in the photoluminescence study [72].The doped nanoparticle was porous, as indicated by a bulk density value as low as 0.13 kg/m 3 .Further co-doping with metal ions imparted exceptional stability to the catalysts, as demonstrated by the retention of photocatalytic efficiency after multiple cycles [34,72].
In a recent study, a one-pot synthesis of photocatalyst SrTiO 3 , doubly modified with silver nanoparticles, was carried out to yield highly stable photocatalysts with BET surface areas as high as 16 m 2 g −1 , pore size of 19 nm, and a reduction in the energy band from 3.2 eV in undoped catalysts to 2.8 eV in the modified ones.The double modifications carried out were the following: doping the photocatalysts with silver nanoparticles and depositing the nanoparticles on the catalyst surface viawet impregnation method [73].In the recent study on MXene-based TiO 2 catalysts, the specific surface area of hierarchical flower-like TiO 2 microspheres decorated with dual cocatalysts-namely, Ti 3 C 2 nanosheets and Ag-measured using N 2 adsorption-desorption isotherms was ~100 m 2 /g, a value slightly lower than pristine TiO 2 .However, the photocatalytic hydrogen production by the composite catalyst was 40-fold compared to the pristine TiO 2 , indicating that the specific surface area did not play a significant role in enhancing the photocatalytic activity of the catalyst, although the adsorption of H 2 O was an essential step in promoting photocatalytic hydrogen production [54].
XRD patterns of a sulphur-doped Sn 3 O 4 photocatalyst indicated that the crystal structures of the catalyst remained unchanged due to doping.Narrowing the bandgap to 2.39-2.43eV, a value smaller than that of pure Sn 3 O 4 , was achieved viasulphur doping.However, SEM studies indicated the destruction of the hierarchical flower-like structure of Sn 3 O 4 due to sulphur doping [74].

The Doping of Adsorbentswith Nanoparticles
Conventional adsorbents like activated carbon and alumina had been longstanding workhorses in removing dyes, heavy metals, and organic pollutants from wastewater [75].However, the quest for more efficient and cost-effective wastewater treatment had shifted the focus towards low-cost adsorbents characterized by rapid adsorption kinetics and exceptional adsorptive capabilities [76].Nanoadsorbents have emerged as promising alternatives to their conventional counterparts in this pursuit.
The superiority of nanoadsorbents lies in their distinct features, notably their remarkable surface area-to-volume ratio, customizable pore sizes, and reduced intraparticle diffusional distances.These characteristics translate into significantly enhanced performance when it comes to the adsorption of pollutants from wastewater.But the story does not end there; researchers hadexplored a novel approach to elevate the efficacy of nanoadsorbents even further-doping with external agents.
In this context, doping represents the infusion of specific compounds or elements into the nano-adsorbent matrix.This infusion process is not limited to a single method; it can be achieved through chemical impregnation or mechanical mixing, offering flexibility in implementation.Heteroatom doping, a prominent technique, involves the substitution of surface carbon atoms with heteroatoms of varying sizes and electronegativities.This substitution brings about an intriguing phenomenon known as charge-transfer doping, wherein the charge distribution within the material wasmodulated, leading to altered adsorption behaviour.Alternatively, defective doping introduces structural imperfections or defects into the adsorbent's architecture, further influencing its adsorption characteristics.
Nitrogen stands out as a widely favoured choice among the array of elements employed as dopants.Nitrogen doping introduces unique properties to the adsorbent, effectively augmenting its pollutant removal capabilities [75].In parallel, incorporating metal nanoparticles into adsorbents had also garnered significant attention.These metal nanoparticle-doped adsorbents offer distinct advantages [76], rendering them increasingly indispensable in wastewater treatment.
In essence, the adoption of nano adsorbents signifies a substantial leap in wastewater treatment technology.Their innate properties make them formidable candidates for pollutant removal.However, researchers can fine-tune these materials by leveraging the power of doping with external agents, enhancing their efficiency and versatility.Nitrogen and metal nanoparticle doping exemplify the innovative avenues explored to create advanced adsorbent materials tailored to meet the evolving demands of efficient pollutant removal from wastewater streams.

Nitrogen Doping
Removing carbon dioxide (CO 2 ) from flue gas using porous carbon adsorbents holds significant promise as a practical technique, primarily due to several advantageous factors.These include the ready availability of the adsorbent, its inherent selectivity towards CO 2 , the simplicity of synthesis methods, and its robust stability even in harsh environmental conditions.The underlying principle of CO 2 adsorption onto carbon materials primarily relies on Van der Waals interactions, which facilitate the physical trapping of CO 2 molecules within aporous structure.However, researchers have harnessed the power of chemical doping to engineer the surface properties of porous carbon materials intentionally.
In this context, doping entails introducing specific impurities or atoms into the carbon lattice, effectively creating tailored electrostatic interactions during the adsorption process.This deliberate alteration induced by doping leads to variations in electron density across the carbon material, giving rise to micro-domains within the pore volume with distinct electrostatic strengths [77].Among the elements considered for doping, nitrogen, boron, phosphorus, and sulphur-known for their relatively higher electronegativity-stand out.When incorporated into the carbon structure, these dopants introduce a positive charge density on neighbouring carbon atoms, enhancing oxygen molecules' adsorption affinity [78].
The strategic introduction of nitrogen atoms into the carbon framework, coupled with subsequent chemical activation, represents a particularly effective approach to maximize the number of active adsorption sites.Nitrogen, in particular, enjoys the status of a favoured dopant for carbon materials due to its closely matched atomic size with carbon and the possession of five valence electrons that readily facilitate bonding with carbon atoms.
Notably, nitrogen-doped carbon adsorbents can be synthesized through various methods, depending on whether the doping process occurs in situ or as a post-treatment step.In situ, nitrogen doping methods encompass solvothermal techniques, arc-discharge methods, substituting nitrogen atoms into the carbon structure during chemical vapor deposition from a nitrogen source, and nonmechanical approaches like ball milling.Conversely, posttreatment doping methods typically involve incorporating nitrogen atoms into available sites created by defects through annealing, hydrothermal treatments, ion implantation, or plasma treatments [78].
Overall, the utilization of porous carbon adsorbents for CO 2 removal from flue gas had garnered considerable attention due to their unique attributes.Nevertheless, by strategically introducing heteroatoms such as nitrogen into the carbon lattice through doping, researchers can significantly enhance the adsorption properties, opening up new avenues for tailoring these materials to achieve even greater efficiency in capturing CO 2 from industrial emissions.

Synthesis of Nitrogen-Doped Adsorbent
The synthesis of nitrogen-doped adsorbents, particularly porous carbon materials, had attracted significant attention among researchers due to their exceptional adsorption capabilities.Various methodologies had been explored to create these adsorbents with tailored properties.In one study, two prepolymer solutions were prepared according to established protocols, one containing resorcinol and formaldehyde dissolved in water and another containing melamine and formaldehyde in water.These two precursor solutions were combined with graphene oxide, forming graphene oxide/melamine resin composites.Nitrogen-doped graphene oxide/melamine nanocomposites with abundant pores and a high surface area were synthesized through a hydrothermal reaction at 80 • C for 24 h to enhance their adsorption capacity further.The resulting composites were subjected to activation in a nitrogen stream, facilitated by a KOH activator, at temperatures ranging from 400 • C to 700 • C for 2 h.Subsequent washing and vacuum drying of the product post-pyrolysis resulted in the desired composite material [79].
In another study, nitrogen-doped porous carbon was prepared by mixing a nitrogen source, specifically carbamide, with anthracite coal particles, along with the activating agent KOH.This mixture was then heated to carbonization temperatures ranging around 800 • C for 4 h.After carbonization, the chips were carefully washed, dried overnight, and subsequently utilized for the adsorption of sulphur dioxide (SO 2 ) [80].
Innovative approaches hadalso been adopted in the synthesis of nitrogen-doped adsorbents.For instance, nitrogen-rich carbon precursor materials, such as renewable leather solid wastes, hadbeen harnessed as a source of porous carbon material.These materials were employed to prepare KOH-activated nitrogen-doped adsorbents specifically designed for highly efficient removal of phenolic substances [81].
To provide a visual representation of the synthesis process, Figure 5 illustrates the schematic diagram depicting the synthesis of nitrogen-doped magnesium oxide-modified biochar-based adsorbent, exemplifying the innovative approaches undertaken in developing nitrogen-doped adsorbent materials [62].These diverse methods collectively contribute to the advancement of adsorption technologies, offering promising solutions for various environmental and industrial applications.

Metal Nanoparticle-Doped Adsorbents
Incorporating metal nanoparticles into adsorbents, known as metal doping, is a highly effective technique to enhance the separation efficiency and surface properties of the adsorbent materials.This process involves the deposition of metal nanoparticles onto the surface and within the pore channels of the adsorbent.Notably, metal doping introduces active metal sites interacting with the carbon matrix, thereby improving the adsorbent's selectivity.Furthermore, doped metals' magnetic properties can facilitate the adsorbent's regeneration, making the process more efficient [83].
Metal nanoparticle doping had widespread application in wastewater treatment, extending beyond porous carbon materials to encompass various other porous adsorbents.Examples of these modified adsorbents include cellulose, zeolite, chitosan, and

Metal Nanoparticle-Doped Adsorbents
Incorporating metal nanoparticles into adsorbents, known as metal doping, is a highly effective technique to enhance the separation efficiency and surface properties of the adsorbent materials.This process involves the deposition of metal nanoparticles onto the surface and within the pore channels of the adsorbent.Notably, metal doping introduces active metal sites interacting with the carbon matrix, thereby improving the adsorbent's selectivity.Furthermore, doped metals' magnetic properties can facilitate the adsorbent's regeneration, making the process more efficient [83].
Metal nanoparticle doping had widespread application in wastewater treatment, extending beyond porous carbon materials to encompass various other porous adsorbents.Examples of these modified adsorbents include cellulose, zeolite, chitosan, and montmorillonite, each of which can be tailored for specific applications through metal doping.The mechanism underlying the doping of porous carbon material with metals is elucidated in Figure 6, which illustrates the interaction between metal and porous carbon [83].One particularly promising area of research involves the development of metal-organic framework (MOF)-based adsorbents doped with metal nanoparticles, such as nickel and copper.MOFs are crystalline porous materials characterized by metal centres interconnected by organic linkers.They offer substantial advantages, including high surface area, porosity, and exceptional thermal and chemical stability.Additionally, modifying the metal centres and linkers can customise MOFs' pore size and functionalities.Doping metal nanoparticles into MOFs can be achieved through various techniques, including chemical vapor deposition, solid grinding, microwave irradiation, and solution infiltration.Previous studies haddemonstrated the effectiveness of MOF modification through palladium doping for toluene adsorption and cerium doping for NO 2 adsorption [84][85][86].
The incorporation of metals into metal oxide adsorbents can be accomplished using several strategies, such as chemical precipitation, sol-gel, solvothermal, and co-precipitation methods.For example, the solvothermal method had been employed to synthesize chromium-doped zinc oxide nanoparticles, efficiently removing methyl orange from wastewater [75].Simultaneously, a hydrothermal approach was utilized to synthesize gadolinium-doped cobalt ferrite nanoparticles [68].Additionally, the removal of radioactive iodine from an alkaline solution, a byproduct of nuclear fission in uranium, was effectively achieved using alumina doped with silver nanoparticles [87].These diverse methods of metal nanoparticle doping continue to drive advancements in adsorption technologies, contributing to their efficacy in diverse environmental and industrial applications.

The Synthesis of Metal-Doped Adsorbents
In the synthesis of metal-doped adsorbents, various methods had been explored to effectively incorporate metal elements into the adsorbent matrix, enhancing their adsorption properties and suitability for specific applications.One study by Cheng et al. [88] employed ultrasound-assisted carbon activation as a key step.This process involved the activation of carbon, followed by impregnation with Fe(NO 3 ) 3 under an ultrasonic treatment for 30 min.Subsequent filtration and drying at 105 • C yielded the suspensions, which were then treated in a microwave to produce iron-doped activated carbon.During ultrasonic treatment, ultrasonic cavitation played a critical role, leading to an increase in the fixed carbon content and a corresponding decrease in other ingredients.This method resulted in the creation of iron-doped activated carbon with improved adsorption properties.
Another approach, the co-precipitation method, was employed to synthesize bariumdoped zinc oxide nanoparticles, which exhibited high effectiveness as adsorbent materials for dyes [89].This method involves the simultaneous precipitation of metal ions, resulting in the formation of doped nanoparticles with tailored properties suitable for dye removal applications.
Additionally, researchers hadconducted a comparative study to evaluate the efficiencies of CO 2 adsorption using various metal-doped MgO adsorbents.This evaluation was based on theoretical calculations of adsorption energy, aiming to identify the most effective dopant for achieving maximum CO 2 removal [90].Density Functional Theory (DFT) calculations played a crucial role in revealing that aluminium-doped MgO exhibited the highest average adsorption energy and the presence of chemisorption structures.Consequently, this interaction between CO 2 and aluminium-doped MgO was identified as the strongest and most favourable among the tested dopants.Due to their ease of separation, transition metals with magnetic properties-including nickel, iron, and cobalt-had been favoured as dopants.Nickel-carbon nanoparticles, for instance, were synthesised using an electrical wire explosion method under 320 V of voltage in an ethanol medium.Subsequent treatment processes, such as sonication, filtration, washing, and drying at 70 • C, yielded nano colloids that effectively removed organic dyes [91].
Furthermore, the modification of graphitic carbon nitride with various metals, including lithium, sodium, magnesium, and calcium, was explored.This involved annealing a mixture of cyanamide and the respective metal chloride at 550 • C for 3 h.The resulting synthesized material was assessed for its efficiency in dye removal applications [92].These diverse methods of synthesizing metal-doped adsorbents showcase the versatility of approaches available for tailoring adsorption materials to meet specific environmental and industrial needs.

Recent Advancements in Doped Adsorbents
A number of investigations hadbeen carried out recently for developing novel porous adsorbent material-namely, metal-organic frameworks, porous polymers, and engineered porous carbon with enhanced adsorption capacities and selectivity.Activated carbon cloth fabricated from precursors like viscous rayon, cotton, and blends and decorated with polypyrrole nanoparticles had been used extensively in CO 2 adsorption with a high CO 2 :CH 4 selectivity.In a recent study, composites of viscose rayon cloth and polypyrrole nanoparticles (VRC-PNP) were prepared viapolymerization followed by carbonization at 850 • C. Nickel doping was performed by immersing the composite fabric into a nickel solution, and the resulting composite achieved a CO 2 :CH 4 selectivity of 369.5 at 20 bar and 298 K [93].A facile one-pot synthesis of nitrogen-doped porous carbons was carried out by grinding a mixture of melamine, hexamethyltetramine, and pluronic;calcinationwas carried out in an N 2 atmosphere, and the mixture was used for drug adsorption with a capacity as high as 110 mg/g [94].In another instance, nitrogen-doped hierarchical porous carbon was prepared by a step activation process with different proportions of cellulose, (NH4) 2 C 2 O 4 and NaHCO 3 /KHCO 3 , and calcining at 900 • C. The nitrogen-doped hierarchical structure possessed a toluene adsorption capacity as high as 585 mg/g, where the micropores and the nitrogen functional groups were the governing factors behind the nd toluene adsorption capacity [95].
The one-step urea hydrothermal method had been used to synthesise magnesium zirconium hydrotalcite-like material doped with Fe 2 O 3 , and ZrO 2 , which were used for fluoride removal from water with an adsorption capacity as high as 113.38 mg/g.The metal oxide nanoparticles and the hexagonal laminae of the hydrotalcite were uniformly stacked, producing a large specific area of the adsorbent [96].Recently, nitrogen-doped carboxylated porous carbon materials were employed to remove heavy metals from water-namely, lead, mercury, and chromium.In this work, four different nitrogen functional groups-namely, graphitic, pyrrolic, pyridinic and pyridine oxide-were combined with carboxyl acid functional groups and incorporated into the porous carbon structure, producing a BET surface area as high as 1135 m 2 /g.A percentage removal of heavy metals as high as 100% was quickly achieved, which was attributed to itshigh adsorption capacity (721 mg/g for lead) and high uptake values [97].The high specific surface area coupled with the chelating action of the carboxyl acid group synergistically increased the percentage removal of metal ions.
Recent studies had reported the synthesis of the nanocomposites of acid-functionalized carbon nanofibers with manganese-doped titanium nanotubes to recover lithium metal viaadsorption.The functionalized carbon nanofibers (ACNF)were synthesized using hot mix acid oxidation, and the manganese-doped TNTs(Mn-TNT) were synthesized by a modified Murray approach.Microwave irradiation was used to deposit the Mn-TNTs on the ACNF.The lithium adsorption capacity of the nanocomposites was 10 times that of pristine ACNF [98].Covalent triazine frameworks (CTF) were a recently developed promising class of adsorbents belonging to the triazine core covalent organic framework (COF) class.They were effectively employed for CO 2 capture [99] and dye removal from aqueous solutions [100].A recent study employed a triazine-based covalent organic polymer with hierarchical micro and mesoporous structures to remove cationic and anionic dye, achieving a 50 mg/g adsorption capacity in an hour [100].Phenylenediamine covalent organic polymer(PDA-COP) functionalized with 3-amino-1,2,4-triazole-5-thiol(ATT) was synthesized by a nucleophilic substitution reaction between cyanuric chloride and para-phenylenediamine, followed by a dropwise mixing of ATT.The ATT@PDA-COP showed a Hg 2+ adsorption capacity of 312.5 mg/g [101].A solvothermal method was used to synthesised a zinc-based coordination polymer adsorbent with a large surface area and porous structure to remove two dyes simultaneouslyusing dimethyl formamide (DMF) and terephthalic acid (TP).The adsorption capacity of the prepared adsorbent for the two dyes-namely, quinoline and azure blue in the binary mixture-was 46.57mg/g and 40.98 mg/g with a three time reusability without a decline in adsorption capacity [102].Nitrogen-rich porous polymers obtained viaco-polymerization of 1,4-bis-(2,4-diamino-1,3,5,-triazine)-benzene with terepthaldehyde and with 1,3,5-tris(4-formylphenyl)benzene resulted in nitrogen-rich porous polymers with a surface area of 1579 m 2 /g and 1028 m 2 /g, respectively.The CO 2 uptake at 1 bar for the first adsorbent was 3.71 mmol/g at 298 K with a CO 2 /N 2 selectivity of 21 and a CO 2 /CH 4 selectivity of 5.3.The CO 2 uptake had been found to depend on pore functionality, while CH 4 uptake depended on surface area.Hence, the CO 2 /CH 4 selectivity was found to be higher for the adsorbent with a lower surface area-namely, the second adsorbent [103].

Applications of Doped Photocatalysts and Adsorbents
Doping photocatalysts with metals and metal oxides enhances their photocatalytic properties, making them valuable in various applications.For instance, bismuth-doped TiO 2 had shown the synergistic enhancement of CO 2 photo-reduction and selectivity towards CH 4 [29].Platinum had been used as an electron-trapping agent to modify bismuth-doped TiO 2 , effectively extracting trapped electrons on the surface of TiO 2 [8].Other studies had explored the use of metal-doped photocatalysts for pollutant and dye removal, demonstrating their potential for environmental remediation [20,21].Additionally, metal oxides can serve as support materials for depositing catalysts, promoting catalytic activity, and improving overall performance [104].
Copper-doped zinc oxide had been employed for treating arsenic-rich water through the oxidation of arsenic (As(III) to As(V)) [105].Researchers had also adopted unconventional strategies, like the solid-state method, to introduce iron into TiO 2 nanoparticles for preparing iron-doped TiO 2 photocatalysts for dye degradation [106].Self-doping TiO 2 nanoparticles with Ti 3+ had been achieved using a one-step solvothermal method, contributing to enhanced photocatalytic activity [107].
TiO 2 with manganese doping on reduced graphene oxide, synthesized through a onepot hydrothermal method, exhibited a remarkable 99% chromium removal efficiency under sunlight within 60 min.Additionally, doping led to a significant 12.85% enhancement in photocatalytic activity [108].
Nanocomposites of TiO 2 and nitrogen-doped reduced graphene oxide were prepared via a urea-assisted hydrothermal method, showcased a noteworthy CO yield of 356.5 µmole g −1 in CO 2 photoreduction reactions, representing a 4.4-fold increase compared to undoped TiO 2 [64].
Furthermore, nitrogen-doped graphene hydrogels were synthesized using a one-pot hydrothermal method, exhibited excellent adsorption and photocatalytic activities for organic pollutant removal.Doping led to a notable increase in the degradation percentage, from 60% to 70%, using the doped catalyst [109].
Fluorine-doped graphene nanosheet (FG)-based photocatalysts were modified with GdVO 4 via an ultrasonication-assisted hydrothermal method, achieved a remarkable 97% removal of phenol from water.Modification with GdVO 4 resulted in a substantial 120% enhancement in phenol degradation compared to pristine FG [67].
The list goes on to include Sn-doped haematite, platinum nanoparticle-doped mesoporous/ZnO photocatalysts, a magnetic NiFe 2 O 4 catalyst supported on nitrogen-doped graphene, chitosan-based nitrogen-doped graphene, doped aluminium nanoparticles/ Moringa oleifera gum-activated carbon, C-doped Bi 2 O 3 nanowires, and neodymium (Nd 3+ )doped CoFe 2 O 4 (cobalt ferrite).These materials demonstrated significant improvements in their respective applications.The beneficial effects of doping photocatalysts through enhancement of their degradation efficiency are shown in Figure 7.
These diverse doping techniques and applications highlight the versatility of metal and metal oxide doping in tailoring the properties of photocatalytic materials, making them suitable for various environmental and catalytic applications.
Doping in adsorbents had played a pivotal role in augmenting their capabilities, leading to diverse applications.For example, a UiO-66 nanoparticle doped with cobalt and synthesized through a single-step solvothermal method, achieved a remarkable 94% removal of tetracycline, boasting 7.6 times greater adsorption capacity compared to pristine UiO-66 adsorbents [112].
In another instance, a bismuth oxide-doped MgO adsorbent, prepared via a coprecipitation method, demonstrated efficient indigo carmine dye adsorption with a maximum dye removal capacity of 126 mg g −1 , surpassing the performance of other magnesiumbased adsorbents [113].
Additionally, Fe(NO 3 ) 3 -impregnated activated carbon, synthesized using an ultrasoundmicrowave combined method, effectively removed dyes from wastewater, exhibiting a maximum adsorption capacity of 259.74 mg/g.The activation process improved the removal capacity by 17.12% compared to non-activated carbon [114].
Furthermore, nitrogen-and phosphorus-co-doped porous carbon, produced through a solvothermal method, displayed a remarkable CO 2 adsorption capacity of 5.68 mmol g −1 at 5 bar, a 2.63-fold increase compared to the undoped adsorbent [115].Other examples include cerium oxide nanorods coated with nitrogen-doped carbon nanoparticles, nickel oxide nanoparticles,-doped PVA-MF polymer nanocomposites, zincdoped SnS 2 nanoparticles, a metal-organic framework with the iron base loaded on iron oxide nanoparticles, nitrogen-doped biochar, and iron-doped natural clay.These materials showcased noteworthy enhancements in their adsorption capacities and efficiency for various applications [116][117][118][119][120][121][122].The improvement of the performance of doped adsorbents over the undoped ones is demonstrated in Figure 8 for various applications.To summarize, this section explores the broad spectrum of applications for metal and non-metal-doped photocatalysts and adsorbents, underscoring their significance in various environmental and industrial contexts.The findings from multiple studies are presented in Tables 1 and 2, offering comprehensive insights into synthesis methods, key outcomes, and substantial performance enhancements realized through doping in these materials.Overall, the tables underscore the transformative impact of doping in photocatalysts and adsorbents, opening new avenues for addressing critical environmental and industrial challenges.

Integrated Photocatalyst-Adsorbent Systems with Doping
The integration of adsorption and photocatalytic degradation processes represents a highly effective approach for removing contaminants, capitalizing on the advantages of both methods while achieving enhanced removal efficiencies.Various synthesis techniques, including sol-gel, microwave-assisted, and wet chemical impregnation, were employed to create these hybrid systems.Numerous studies are reported in the literature-exploring the potential of integrated adsorption-photocatalytic units incorporating doping elements [133,134].
For instance, using the sol-gel method, a significant improvement in phenol degradation was achieved by synthesising a fluorine-doped TiO 2 supported on an activated carbon adsorbent.Under visible light, this integrated system exhibited an impressive 61.2% degradation rate, whereas the undoped counterpart managed only a 13% degradation rate [134].
In another study, zirconium-doped TiO 2 nanoparticles immobilized on delaminated clay, prepared via the sol-gel route, demonstrated enhanced photocatalytic activity under solar radiation.The doped unit achieved approximately 90% removal of antipyrine in just 4 h-notably, the pollutant degradation reaction rate correlated with the irradiation intensity [135].
In a more recent investigation, the co-doping of titania nanoparticles coated on activated carbon with cerium and nitrogen was carried out to improve the degradation efficiency of sodium isobutyl xanthate under visible radiation.Employing the sol-gel route for doping, the doped adsorbent-photocatalyst system exhibited an impressive removal efficiency of 96.3% within 5 h, with a cerium dosage of 2%.Bycontrast, the undoped unit achieved a mere removal rate of approximately 9.8% within the same timeframe [136].
Furthermore, iodine-doped biochar demonstrated efficient adsorptive and visiblelight-driven photocatalytic capabilities in removing organic pollutants in a study conducted by Wang and colleagues.The hydrothermal treatment of biochar with iodine resulted in the doped sample, which, when integrated for adsorption and photocatalysis, achieved a remarkable 100% removal of the pollutants [137].
Cerium-bismuth oxides/oxynitrides prepared viadoping bismuth in ceria using a chemical precipitation technique served as bifunctional adsorbent/photocatalysts in the effective removal of toxic organophosphate by reactive adsorption followed by photocatalytic degradation.A near 100% removal of methyl paraxon was achieved during the reactive adsorption [138].
These examples underscore the immense potential of integrated photocatalyst-adsorbent systems with doping elements to address complex contamination challenges and provide a glimpse into the promising future of environmental remediation technologies.

Conclusions and Future Perspective
In conclusion, the quest for efficient photocatalytic materials hinges on the crucial stability and durability requirements during real-time operation.While certain materials like metal sulphides and chalcogenides initially exhibit high photocatalytic activity, they were prone to photocorrosion under irradiation.Bycontrast, titanium dioxide (TiO 2 ) stands out as a highly stable photocatalyst with significant catalytic prowess.Among the various phases of TiO 2 , the anatase phase emerges as the most active, although it necessitates shortwavelength light, typically around 350 nm, to initiate its catalytic activity.Researchers had actively explored doping with both metals and non-metals to harness TiO 2 s potential in the visible region and reduce carrier recombination rates.
However, it is crucial to acknowledge that doped photocatalysts come with certain limitations.Metal doping, for instance, can result in unstable materials prone to corrosion, with the metal dopant leaching over time, leading to a decline in photocatalytic activity [139].On the other hand, non-metal doping often demands stringent preparation conditions, and maintaining an optimal dopant loading is paramount; otherwise, it can significantly impair the photocatalyst's activity.In response to these challenges, researchers hadincreasingly turned to co-doping with metals and non-metals as a strategy to mitigate the limitations of single-element doping.Metal-organic frameworks have attracted attention as potential adsorption and photocatalyst candidates for degrading organic contaminants.However, they suffer from limitations like metal ions and ligands leaching into the solution.To improve the structural stability, photocatalytic, and adsorptive ability during real-time operations, doping with graphene oxide, silver, and activated carbon for preparing MOF-based composites had been carried out.However, most of the studies report the performance of these composites in synthetic wastewater.Rigorous studies need to be performed to test the stability of these composites in industrial wastewater to ascertain their suitability for working with real-time effluents [140].
Although many studies have reported the enhancement of photocatalytic activities of doped catalysts, more studies need to be reported on the physicochemical stability and reusability of the doped photocatalysts while handling large volumes of industrial effluents.Rigorous studies need to be carried out on the possible combination of doped photocatalyst-based pollutant removal with biological means and electrodynamic removal.The fundamental quantification of the doped photocatalysts' reactivity, toxicity, and fate must be reported [141].
In volatile organic compound (VOC) degradation, metal/metal co-dopants, such as silver and vanadium co-doping in TiO 2 nanoparticles, had served a dual role: ensuring uniform metal dispersion on the photocatalyst and creating oxygen vacancies.In the case of non-metal co-dopants, research had demonstrated that co-doping with carbon and nitrogen in TiO 2 can synergistically enhance VOC degradation without altering the catalyst's morphology [142].However, it is important to note that co-doping may also present challenges, including the potential for enhanced electron-hole pair recombination and nanoparticle shielding effects.Therefore, comprehensive studies are needed to investigate the impact of doping on photocatalyst structure and stability, identify optimal process parameters for maximising doped photocatalyst efficacy while minimizing dopant leaching, and assess the performance and stability of doped catalysts in large-scale industrial systems, particularly in reactors with high-temperature conditions and agitator speeds.
In the field of adsorbents, doping carbon-based materials with nitrogen holds promise for enhancing adsorption capabilities and improving CO 2 /N 2 selectivity.Nitrogen doping facilitates CO 2 uptake by enhancing the surface area and promoting interactions between acidic CO 2 molecules and basic nitrogen functionalities.Notably, co-doping with nitrogen and oxygen had yielded adsorbents with the highest CO 2 adsorption capacity.However, the highest CO 2 /N 2 selectivity was achieved when the doped adsorbent featured abundant basic nitrogen functional groups, such as pyridinic and pyrrolic groups, regardless of the specific surface area.Hence, synthesising carbon-based adsorbents with optimized ultra microporous surface areas and essential basic heteroatoms was crucial to achieving high CO 2 uptake values and selectivity [143].
The overall adsorption efficiency of an adsorbent was governed by the various mass transfer resistances encountered during the operation, and an in-depth analysis of the effect of doping on the mass transfer resistance needs to be carried out.For instance, in the case of fixed-bed adsorbents, the modelling of transport equations depends upon the mass transfer mechanism from the adsorbate to the adsorbent phase.Both intraparticle and external film resistances need to be considered.The relative significance of the two mass transfer resistances is governed by the Biot number (kL/D), where D is the internal diffusion coefficient, k is the external film coefficient, and L is the characteristic dimension.The Biot number ranges from 5-500 in fixed beds, indicating significant mass transfer resistance in the particles.It had been observed that micropore diffusion resistance predominates over macropore and film resistances [103].However, a detailed study on the mass transfer effects affecting the performance of the doped adsorbents in different contacting devices needs to be carried out to establish the viability and suitability of the adsorbent in real-time operations.
Looking ahead, further advancements in the field of photocatalysts and adsorbents should focus on addressing these challenges and optimizing doping strategies to meet the growing demand for efficient and sustainable environmental remediation technologies.Extensive research in large-scale systems, industrial reactors, and real-world applications will be instrumental in realizing the full potential of doped materials in tackling environmental pollution and promoting a cleaner, healthier future.

Figure 6 .
Figure 6.The mechanism of doping between metal and porous carbon [83].