An Approach to Delineate Potential Groundwater Zones in Kilinochchi District, Sri Lanka, Using GIS Techniques

The scarcity of surface water resources in the dry season in the Kilinochchi district increases the demand for freshwater. Therefore, the main objective of this study is to delineate potential groundwater zones in Kilinochchi, Sri Lanka, using integrated remote sensing (RS), geographic information systems (GIS) and the analytical hierarchy process (AHP). Groundwater potential zones are demarcated for the Kilinochchi district by overlaying thematic layers: geology, geomorphology, land use/land cover, soil types, drainage density, slope, lineament, and rainfall. The thematic layers were integrated into a geographic information system, and a weighted overlay analysis was carried out to delineate groundwater zones. Thus the resultant map is categorized into five different potential zones: very low (59.12 km2), low (207.78 km2), moderate (309.89 km2), high (507.74 km2), and very high (111.26 km2). The groundwater potential map was validated with the existing seventy-nine wells, which indicated a good prediction accuracy of 81.8%. This suggests that the results obtained by integrating RS-GIS and AHP are well-matched with the existing well water depth. The AHP approach based on RS-GIS was a handy and efficient technique for assessing potential groundwater zones. This research will help policymakers better manage the Kilinochchi district’s groundwater resources and give scope for further research into groundwater exploration in the area.


Introduction
Groundwater or subsurface water is "a term used to denote all the waters found beneath the ground surface" [1]. Groundwater is defined as "water in a saturated zone, filling the pore spaces among mineral grains or cracks and fractured rocks in a rock mass" [2]. Naturally, the water from rain and snow infiltrates through soil or the pore spaces of underlying rocks to replenish the groundwater [1,2]. Therefore, climate, characteristics of surface and subsurface, and their relationship with hydrology decide the occurrence and distribution of groundwater [1]. About one-third of the world's population utilizes groundwater for drinking purposes [3], and demand for groundwater increases worldwide due to many factors such as population growth, advanced irrigation practice, industrial usages, etc. [4][5][6]. Population growth, increasing irrigated agriculture practices, and economic development have all increased groundwater usage and demand, with little consideration for the importance of the environmental balance of groundwater [7,8]. The total groundwater extraction has many uses worldwide: 36% for households, 42% for agriculture, and 27% for industries [8,9]. Notably, there is tremendous pressure on groundwater in developing countries [10].
Agriculture is vital to the Sri Lankan economy [11]. In Sri Lanka, water availability and demand for it vary spatially and temporally. Groundwater is widely used across Sri platform to build conceptual models for identifying potential groundwater zones in a given area [31,32,37,44,45].
The application of RS and GIS in groundwater resource exploration has become a milestone in groundwater research that provides substantial support for analyzing, monitoring, and protecting groundwater resources [8,46]. Incorporating RS and GIS into groundwater potentiality mapping allows for data storage, manipulation, and analysis [44,47]. Integrated GIS and RS with AHP prove that it is a handy tool for delineating potential groundwater zones by reducing time and cost [4,17,32,37,41,44,45,[48][49][50]. Researchers adopt various techniques for delineation potential groundwater zones: statistical method [51], influence factor (IMF) [36,38,40,52], groundwater modelling, the combination of GIS, RS with AHP [37,41,45,49], and GIS-based machine learning [39,53,54]. Many researchers have adopted these methods since they have been demonstrated to be reliable and effective. In addition, several factors are often considered in the integrated approach to reduce inaccuracy and human error ( Table 1). AHP is recommended among these methods when there are several alternatives for a set of pairwise comparisons and a lack of adequate valid data for analysis [30,55]. Recently, remote sensing and GIS coupled with AHP techniques have been adopted as a standard methodology for delineating potential groundwater zones in semi-arid areas [37,41,45,49]. AHP is used in conjunction with RS-GIS techniques to delineate possible groundwater zones in the Kilinochchi district. The thematic layers used to delineate groundwater zones vary among research as the selection of attribute layers is arbitrary. In addition, weight assignment for each thematic layer and its classes has been determined based on expert opinion and site-specific conditions. This study used eight factors, including geology, geomorphology, land use/land cover, soil types, drainage density, slope, lineament, and rainfall, to delineate the potential groundwater zones. In the present study, AHP techniques combined with RS-GIS methods delineate the groundwater potential zones. AHP is considered a simple, transparent, effective, and reliable technique for delineating groundwater potential zones [9]. As groundwater is dynamic, RS data integration into the GIS is convenient for identifying the potential groundwater zones (GWPZ). Forootan and Seyedi, [45] x x x x x x x x Doke et al., [41] x x x x x x x x Karimi-Rizvandi et al., [39] x x x x x x x x x x Aslan and Çelik, [17] x x x x x x x x x Jhariya et al., [40] x x x x x x x x Sarwar et al., [52] x x x x x x x Nasir et al., [36] x x x x x x x Kumar et al., [37] x x x x x x x x x x Dilekoglu and Aslan, [49] x [38] x [44] x x x x x x x x Achu et al., [32] x x x x x x x Ajay Kumar et al., [50] x x x x x x x Ahmad et al., [47] x [56] x [57] x x x x x x x Qadir et al., [58] x x x x x x Lentswe and Molwalefhe, [48] x x x x x Sl-Slope, Lu-Land use, Ge-Geology, Li-Lithology, Gm-Geomorphology, Rf-Rainfall, SPi-Stream Power Index, El-Elevation, So-Soil, Ld-lineament density, Rd-River density, If-Infiltration TWi-Topographic wetness index, STi-Sediment transport index, Cu-Curvature, Dd-Drainage density, Al-Altitude, Dr-Distance from the river, Aq-Aquifer, Dg-Depth to groundwater.
Groundwater is the primary source of drinking and agricultural practice in the Kilinochchi district [22]. It is indiscriminately extracted in many parts of the district, as surface water is insufficient to satisfy the demand. Hence, authorities need to identify the presence of groundwater. The study area consists of several wells, which demonstrate the importance of groundwater to the district's socio-economic growth. Apart from its significance, a limited number of studies (only one study) on groundwater within the study region has been undertaken to date [21], and only five relevant elements were evaluated in that article. In the current study, eight groundwater influencing factors, including geology, geomorphology, land use/land cover, soil types, drainage density, slope, lineament, and rainfall, are integrated into the GIS platform with the help of the AHP technique to identify potential groundwater zones within the study area. Identifying, monitoring, and preserving the potential groundwater zones is essential for informed decision-making about groundwater resource development strategies [59]. Thus, the delineation of potential groundwater zones by an appropriate modelling approach is necessary to address the water scarcity problem of the drought-prone district. Therefore, the study's main objective is to delineate potential groundwater zones in the Kilinochchi district using RS, GIS, and AHP techniques. ROC and AUC from observed wells' data were used to validate the robustness of RS-GIS and AHP approaches. Moreover, the efficiency of GWPZ mapping was validated by using existing wells' water depth in this region.

Study Area
Kilinochchi district is situated in the Northern Province of Sri Lanka and bounded in north and east by Jaffna district, and on the south by Mullaitivu district and on the east by the Indian Ocean. It lies between the north latitudes 9 • 12 30" and 9 • 41 00" and east longitude 79 • 58 30" and 80 • 37 30" and spread over 1237.11 km 2 ( Figure 1). The study area falls within the dry zone (annual average rainfall of <1750 mm) that extends over two-thirds of Sri Lanka, covering the northwestern, north-central, northern, northeastern, eastern, and southeastern regions of the country [60] and consists of two types of aquifers: deep confined aquifers and shallow regolith aquifer of the Hard Rock Region [14]. The average annual rainfall of the district is 1520.57 mm. The monthly mean temperature is between 25 • C and 30 • C [61]. Geologically, the major part of the Kilinochchi district constitutes alluvial and lagoonal clay, silt sand, whereas the western parts represent red earth and red and brown sand. Jaffna limestone (Minihagalkanda Beds), undifferentiated Vijayan gneiss with trend lines, beach, and dune sand are also seen. The elevation of the district ranges from 49.63 m in the southern part to less than 6.6 m in the northern region. The topography of the area exhibits relatively flat terrain covering a larger part of the coastal zone. The Kilinochchi district is occupied by seasonal rivers and streams, which flow northwards to the Indian Ocean. The soil type of the district is dominated by red-yellow latosols and followed by alluvial soils of variable texture, alkali and saline soils of varying texture (Solodized Solonetz and Solonchaks), sand regosols on the recent beach and dune sands and red-yellow podzolic soils.

Methods
Integration of RS-GIS and AHP technique can be described as a process that translates and harmonizes geographical data and weightage ranking to extract information for decision making (Figure 2) [9]. The overall concept of the study included integrating eight thematic layers of geology, geomorphology, soil, drainage, slope, land use and land cover, rainfall, lineament [13,14,23] processed by weighted overlay analysis using ArcGIS 10.4.1 to generate a potential groundwater zone ( Figure 3). The potential groundwater zones have been delineated using integrated RS-GIS, and AHP techniques. Integrating remote sensing data into the GIS platform is one of the viable options for delineating potential groundwater zones. Required data were gathered from various government agencies, field surveys, and publicly available satellite imagery on the United States Geological Survey (USGS) Earth Explorer website. Thematic layers preparation consists of digital image processing, digitizing existing maps, and field data. All data are geo-rectified and projected to GCS WGS 84 UTM zone 44 North for easy handling in ArcGIS 10.4.1. The present analysis has been based on several types of data from different sources. Table 2 provides a detailed summary of the data sources. Drainage density map and lineament density map were produced using a line density analysis tool in ArcGIS 10.4.1.   Advanced Spaceborne Thermal Emission and Reflection Radiometer-Global Digital Elevation Model (ASTER-GDEM) with 30 m resolution was used to generate a slope map, drainage density map, and lineament map. Those maps were then reclassified to generate the map. The rainfall data were spatially interpolated with inverse distance weighting (IDW) to obtain the rainfall distribution map. IDW interpolation uses a weighted collection of sample points to calculate cell values. Its general concept is that the attribute value of an unsampled location is the weighted average of known values in the surrounding area [67]. The idea is that sampled points closer to the unsampled point are more comparable in their value than those further away. In this study, the deterministic model of the IDW method is used to interpolate spatial data based on the concept of distance weighting. Long-term observed rainfall data were required for analysis in utilizing IDW to interpolate spatial rainfall [37,68,69]. As a result, this study used average rainfall data from 1990 to 2020 over 30 years. It can predict unknown spatial rainfall data using available data from nearby places [37,68].
An accuracy assessment of land use and land cover (LULC) was conducted to assess the accuracy level of the resulting classes. A stratified random sampling method was applied to generate 250 random points, and Google Earth imagery was used as the ground truth reference to examine the random points. The date of the Google Earth imagery was concurrent with the LULC map. A confusion matrix was applied to compute the user's accuracy, producer's accuracy, and overall accuracy for the LULC map with the data obtained from comparisons between the reference and actual points. The accuracy was found to be 88% overall classification accuracy and 0.84 overall kappa coefficient. The overall accuracy of 85% is often considered explicitly as the standard of acceptability of thematic mapping using remotely sensed images [70]. The following equation was applied to calculate the overall accuracy [71].
where OA is overall accuracy, n ii is the number of correctly classified pixels, N is the total number of pixels, r is the number of rows. The key factors influencing the groundwater potential are geology, geomorphology, soil, drainage density, slope, land use and land cover, rainfall, and lineament density [50,58,60,[72][73][74][75][76]. Therefore, eight thematic layers (parameters) such as geology (Ge), geomorphology (Gm), land use/land cover (LuLc), soil types (St), drainage density (Dd), slope (Sp), lineament (Lt), and rainfall (Rf) are considered to delineate the potential groundwater zones in the Kilinochchi district. Based on previous literature studies and expert opinion obtained through snowball sampling from 17 experts from various professions, Saaty's scale was applied to the assigned weights of the chosen eight thematic layers and their features with respect to their influence on groundwater storage ( Table 3). The highest and lowest weights were allocated to the themes of the strong groundwater potential and weakest groundwater potential, respectively [1,4,56,74,76,77]. The methodology adopted for the present study is shown in Figure 3. These layers are geo-referenced and vectorized from various spatial data sources such as the topographic sheet scaled 1:50,000 of Survey Department of Sri Lanka, Geological Map of Sri Lanka, Geomorphological Map of Sri Lanka, Soil Map of Sri Lanka of Geological Survey and Mines Bureau of Sri Lanka, and satellite images (ASTER GDEM and Sentinel-2) of USGS. These thematic layers were converted into a raster format of 30 m resolution and subjected to weighted overlay analysis in Arc GIS 10.4 environment. Field data have been used to verify the accuracy of the groundwater potential map to ensure that the specified areas meet the conditions on the field.

Assignment of Weight and Weight Normalization
The multi-criteria decision analysis (MCDA) is a generally recognized and highly appropriate technique for complex decision-making problems. Standardized weights were allocated by using Saaty's scale (1980). The AHP helps to find out the weight of criterion by pairwise comparison [78,79]. The AHP is a concept of measurement by pairwise comparison matrix (PCM) and is based on the judgment of experts to derive priority weights [74]. The worldwide academic network progressed the integrated GIS and AHP technique to investigate complex spatial issues [50,56,72,74,75,80,81]. PCM for thematic layer, viz. geology, geomorphology, soil, drainage density, slope, land use and land cover, rainfall, and lineament density, is calculated based on Saaty's 1-9 scale weights. Local knowledge and expertise are used to assess the value of the Saaty's scale of each thematic layer. The weights were given according to their potential for groundwater recharge. The high weight is assigned to the themes of good groundwater potential, and the least weight is assigned to poor groundwater potential.
The relative weight matrix and normalized weights were determined based on the PCM to determine the percentage of impact on groundwater recharging of the thematic layers (Table 4). The key principle for checking the comparison order is that the consistency ratio (CR) not equal to 0.1 indicates a satisfactory reciprocal matrix. The ratio above 0.1 indicates the change of the PCM [74]. The CR is determined using the following equation: where RI is the random index, the value of RI for different n values depends on the order of the matrix, and CI is the consistency index which can be expressed as follows: Here, (λmax) is a principal eigenvalue, n is the number of factors, and CI is the consistency index. The CR value for consistent weights should be below 0.10; in the absence of this, corresponding weights should be re-examined to prevent inconsistency [78]. In this study, the CR is found to be 0.088 (λmax = 8.86, n = 8, RI = 1.41, CI = 0.123); which indicates a good consistency in the pairwise matrix comparison (Table 4). Hence, the AHP technique exhibits reasonable precise spatial prediction of groundwater probability.

Normalized Weights of Different Features of Thematic Layers
The attributes of each of the thematic maps were assigned a weight of 1-5 (1 denotes very low, 2 implies low, 3 indicates moderate, 4 represents high, and 5 denotes very high), considering its influence on the occurrence of groundwater [12,50,56,77,82,83]. Table 5 displays the ranks of different features of the individual themes and their normalized weights regarding groundwater potentiality. Every thematic layer has five classes, and their interdependence is complicated. Therefore, the relationship between different features of the individual themes is achieved using other ranks and distinguished by using AHP.

Groundwater Potential Index
The groundwater potential index (GWPI) is a dimensionless quantity that helps predict the potential groundwater zones in an area [4,50,56,72,74]. The weighted linear combination method was used to estimate the GWPI [84,85]. The following equation was applied to integrate all the themes for obtaining the potential groundwater zone as stated below: GWPI = (Gm w Gm wi ) + (Ge w Ge wi ) + (LuLc w LuLc wi ) + (Dd w Dd wi ) + (Sp w Sp wi )+ (Ld w Ld wi ) + (St w St wi ) + (Rf w Rf wi ), where Ge stands for geology, Gm stands for geomorphology, LuLc stands for land use/land cover, Dd stands for drainage density, Sp stands for the slope, Ld stands for lineament density, St stands for soil type, Rf stands for rainfall, w stands for the normalized weight of a theme, and wi stands for the normalized weight of each class.

Factors
Affecting the Groundwater Potentiality in the Study Area 3.1.1. Geology Geology determines the aquifers which store groundwater. The porosity and permeability of a formation assess its quality as an aquifer [57,73]. The spatial distribution of groundwater is primarily influenced by the geological characteristics of an area [57,74,75,86,87]. The geology map of the Kilinochchi district was prepared by digitizing the geology map of Sri Lanka, published by the Geological Survey and Mines Bureau of Sri Lanka [63]. Five types of geology, namely alluvial and lagoonal clay silt sand and red earth, red and brown sand, beach and dune sand, Miocene limestone (Jaffna limestone), and undifferentiated Vijayan gneiss with trend lines are found in the study area. The detailed geological map of the study area is presented in Figure 4. In general, this area belongs to Phanerozoic rock and Precambrian rock. The Phanerozoic rock comprises Alluvial and lagoonal clay silt sand, red earth red and brown sand, beach and dune sand, Miocene limestone (Jaffna limestone). Precambrian rock consists of undifferentiated Vijayan gneiss with trend lines. Alluvial and lagoonal clay silt sand distributed most of the study area predominantly. Although alluvial and lagoonal clay silt is primarily found in the eastern part of the district, it is also distributed throughout the study area. The flow of seasonal rivers in the study area carry alluvial deposits, which are fine sediments with poor sorting order, varies in particle size from clay to sand. Groundwater exploration in this area is deemed relatively successful. The western part mainly comprises red earth, red and brown sand, which are sandstones having quartz and feldspar mineral compositions. It is red and brown in the hue in the studied area. These rock formations allow water and other fluids to percolate easily and are porous enough to retain significant amounts of water, making them valuable aquifers [88]. Beach and dune sand was found in the study area as patches. The water table is deeper beneath dunes and raised beaches [89]. The northeast coastal headland of the study region contains separated extensive coastal sand dune belts.
Miocene limestone (Jaffna limestone) found in the northern part has high groundwater potential. The limestone is a compact, firm, somewhat crystalline rock that dates back to the early Miocene period [88]. The zones having less compaction, a high degree of weathering, and a high degree of infiltration of runoff are more suitable for groundwater recharging [60]. Sedimentary rocks have higher primary porosity and permeability than other types of rocks [73]. Precambrian rock consists of undifferentiated Vijayan gneiss with trend lines, primarily granitic rocks with relatively limited porosity, including garnet and feldspar [88]. They are referred to as "poor aquifer zones." Hence, the various rock units in the study area are assigned appropriate weights based on their textural properties and the potential for fractured zone formation. Based on the nature of increasing groundwater potentiality, the high weight was assigned to Miocene limestone (Jaffna limestone), whereas low weight was assigned to undifferentiated Vijayan gneiss ( Table 4). The groundwater potential map validated with field observation reveals that Miocene limestone (Jaffna limestone) has the highest groundwater potential.

Geomorphology
Geomorphology is a study of landforms that includes their description, species, and physical processes that have helped evaluate possible groundwater areas [57,74]. Geomorphological components are significant in hydro-geological investigations and the identification of groundwater resources [50,57,86]. Morphology has a positive influence on the percolation of water into the earth's subsurface [56,76,90]. Geomorphology is considered an essential component for groundwater recharge as the evolution of landforms explains porous and permeable zones [60]. The geomorphology map of the Kilinochchi district was prepared by digitizing the geomorphology map of Sri Lanka, published by the Geological Survey and Mines Bureau of Sri Lanka [64]. The lithology and geological formation of the study area are highly influenced by geomorphology. Groundwater flow and storage are dominated by geomorphology in any location [91]. The primary geomorphological units of the study area are divided into five types: beach ridges, bars and spits, low plantation surface with inselbergs and thin soil, river plains and adjacent coastal lowlands, upwarped Pleistocene coastal plain, and plateau of Miocene limestones ( Figure 5).
Coastal landforms of sandy beaches, ridges, bars and spits are found in the north and west part of the study region. Coastal barriers called beach ridges shift landward in response to changes in sea level, sediment supply, and coastal erosion [89]. They are the bi-directional transitional zone between terrestrial and marine processes. Sandy beaches are often located in bays with shallow water and low-energy waves. Tidal currents determine the directions of spits and bar growths. Waves and tides cannot cross a spit; therefore, the water behind a spit is very sheltered. Therefore the impacts of beach ridges, bars, and spits on the groundwater are significant in the study area.
Low plantation surface with inselbergs and thin soil is located in the south of the study area. These are erosional remains of the earliest plain surface, characterized by domes of Vijayan gneiss and quartzite. The drought-tolerant vegetation is more prevalent in this area. The study area consists of eroded terrain and erosional remains (inselbergs), accelerating runoff water from the steepness. Thus, the groundwater recharge capacity in erosional remnants was limited [92]. River plains and coastal lowlands cover the major portion of the study area. Most of the rivers are seasonal and have seasonal impacts on the groundwater too. The rivers carry fluvial deposits, and river beds accumulate groundwater during the Northeast monsoon from November to February. An extensive belt of Miocene (5-20 million years ago) limestone is found along the Northeast coast, overlain in some areas by Pleistocene (1 million years ago) deposits, consisting of relatively flat terrain and rising significantly above the surrounding area with some steep slopes. Miocene limestones have a series of openings or caves that make an excellent aquifer which raises the groundwater level.
The major portion is occupied by river plains and adjacent coastal lowlands in the district, while the western part is predominantly formed upwarped Pleistocene coastal plain ( Figure 5). Geomorphological features are weighted in terms of their importance over groundwater occurrence (Table 5). Among these morphological features, the plateau of Miocene limestones has been assigned high weight as it has good potential for groundwater. Still, upwarped Pleistocene coastal plain landforms are assigned low weight as they are unsuitable for potential groundwater zones.

Slope
The slope (the rate of elevation change) is also a key factor in identifying potential groundwater zones [1]. It can be used as an indicator for demarcating potential groundwater zones as it directly controls the groundwater recharge rate [50]. Generally, an inverse relationship can be seen between the slope and the infiltration rate. Surface water penetration is regulated directly by the slope gradient [1,50,75,76,93]. Steep slope experiences a low penetration level due to the rapid flow of water downwards and insufficient time for infiltration, whereas the flat surface facilitates groundwater recharge by retaining rainwater [50,75,94]. The slope map of the Kilinochchi district was derived from the ASTER-GDEM. The slope gradient of the district ranges from <0.50 to >2.00. The slope of the entire district has been categorized into five classes, viz, <0.50, 0.50-10, 10-1.50, 1.50-2.00, and >2.00. Weights were assigned based on the slope categories given in Figure 6. High weight was allocated for lower slopes due to the higher groundwater recharge rate and vice versa ( Table 5).

Soil
Surface water penetration into the aquifers is controlled by the soil [76]. In the unsaturated zone, moisture content, infiltration rate, grain size, and soil composition influence the groundwater movement [50,57,95]. Soil texture affects infiltration rate since the texture varies with porosity and permeability [57,75]. The soil map of the Kilinochchi district was prepared by digitizing the soil map of Sri Lanka, published by the Department of Irrigation Sri Lanka [65]. Five soil types are described in the study area: alkali and saline soils of variable texture (Solodized solonetz and solonchaks), Alluvial soils of variable texture, and red-yellow podzolic soils, red-yellow latosols, and sand regosols on the recent beach and dune sands ( Figure 6). The soil type analysis shows that the study area is primarily covered by red-yellow latosols followed by alkali and saline soils of variable texture (Solodized solonetz and solonchaks), which were observed along the northern and western margin of the coast. Alluvial soils of variable texture mainly cover the middle and eastern parts. The sand regosols on the recent beach and dune sands also occur in the northern boundary of the area. The red-yellow podzolic soil covers the smaller portion in the southern part of the study area (Figure 7). The weights of soils are assigned according to their degree of infiltration [74,96]. The sand regosols on the recent beach and dune sands soil have a high infiltration rate and, therefore, higher priority. In contrast, the red-yellow latosols soil has the lowest infiltration rate and, therefore, is given as low priority (Table 5).

Drainage Density
Drainage density is one of the influential factors in groundwater potential that control surface runoff and permeability [57,74]. Drainage density and the drainage structure are generally controlled by geology, slopes, and structures [57,74]. Drainage density is the proximity of the distance between stream channels, and it indicates the ratio between the total stream length and total area [1,72,87,97]. The drainage density of the Kilinochchi district was prepared from the ASTER GDEM in ArcGIS 10.4. platform. Figure 8 shows the drainage density of the study area. The less permeable layer below the high drainage density area increases surface runoff, indicating less groundwater potential. Therefore, the region with a high drainage density is unlikely to suit groundwater [56]. The drainage density varies between <28.48 and 113.89 km/km 2 in the study area and are categorized into five categories namely <28.47 km/km 2 , 28.47-56.94 km/km 2 , 56.94-85.42 km/km 2 , 85.42-113.89 km/km 2 , >113.89 km/km 2 . High weights have been allocated to the lowdrainage area for potential groundwater delineation, while high drainage area has been assigned low weights (Table 5).

Lineament Density
Linear and curvilinear structural features of an area support groundwater movement and infiltration [10,50,56,93,98]. Higher lineament densities are considered ideal for the development of groundwater [83]. The lineament map of the study area was generated from ASTER GDEM. The lineament density of the study area varies from <0.08 to >0.62 km/km 2 ( Figure 9). The lineament density, shown in Figure 9, is natural, linear or curvilinear features, and was classified into five classes namely, <0.08 km/km 2 , 0.08-0.23 km/km 2 , 0.23-0.41 km/km 2 , 0.41-0.62 km/km 2 , >0.62 km/km 2 . The weights were assigned based on density. Low lineament density was assigned low weight, whereas high weight was assigned to high lineament density (Table 5).

Rainfall
Rainfall impacts significantly the hydrological cycle, which has a dominant effect on the area's groundwater capacity [1,82,97]. The amount of infiltration heavily depends on the intensity and duration of rainfall [1,87]. About 75% of the district's total rainfall is from the northeast monsoon from September to December [61]. There are only a few rain gauge stations in the Kilinochchi district. Annual rainfall data was obtained from three stations: Iranamadu, Akkarayan, and Kariyalainagapaduvan. The rainfall data were spatially interpolated with IDW to get the rainfall distribution map. The yearly precipitation of the study area varies between 94 and 107 mm [61] and is classified into five categories as <97 mm, 97-100 mm, 100-103 mm, 103-106 mm, >106 mm ( Figure 10). The weights were assigned based on the intensity and its potential to groundwater. The high intensity of rainfall was assigned high weight, whereas low weight was allocated to the low intensity ( Table 5). The thematic rainfall map of the Kilinochchi district indicates that although there is high rainfall in the eastern region, the western part of the district has relatively low rainfall ( Figure 10).

Land Use/Land Cover
Groundwater recharge depends on the area's LULC [10,50]. It provides essential information on infiltration, soil moisture, groundwater, surface water, etc. [57,99]. The land use and change map was generated from the Sentinel-2 imagery of May 2020, acquired from USGS Earth Explorer and classified using supervised classification ArcGIS 10.4. Forests, agriculture and fallow lands, barren land, settlements, and water bodies are the main categories of land used found in the area (Figure 11). The land used for water bodies and vegetation is highly suitable for groundwater recharge [57]. Water bodies retain surface water during the monsoon period, and forest cover increases infiltration by minimizing runoff. The land used for agricultural purposes can be categorized as moderately suitable land for groundwater recharge. The built-up area is categorized as the least suitable area for groundwater recharge [75]. The weights were given according to their potential for groundwater recharge. The water bodies are allocated high weight, and the settlements are allocated the least weight (Table 5).

Delineation of Potential Groundwater Zone
Geomorphology, geology, soil, and rainfall play an essential role in the study area's groundwater potential. The integrated RS, GIS, and AHP technical methods have been applied to delineate potential groundwater zones. In PCM, the expert's opinions and field knowledge assigned importance to each theme on Saaty's scale. Geology obtained the highest normalized weight, followed by rainfall, geomorphology, land use land cover, lineament density, soil, slope, and drainage density.
The groundwater potential map are classified into five classes namely very high (111.26 km 2 ), high (507.74 km 2 ), moderate (309.89 km 2 ), low (207.78 km 2 ), and very low (59.12 km 2 ) covering about 9%, 42%, 26%, 17%, and 5% respectively ( Table 6). The normalized weights of the eight thematic layers indicate that geology and rainfall influence more than other factors in the occurrence of the potential groundwater zones (Table 3).  26 9 The map shown in Figure 12 gives an overview of groundwater potential in the study area. Groundwater potentiality map of Kilinochchi district shows that the very high groundwater potential zone is predominantly found in the northeastern part, which includes several Grama Niladhari (GN) divisions (e.g., Masar, Soranpattu, Mullaiyadi, Pulopalai, Palai town, Tharmakerny, Kachcharvely, Vembatukerny, Kilali) under Pachchilaipalli Divisional Secretariat (DS) due to high rainfall (103 mm-106 mm), Jaffna limestone, sand regosols on the recent beach and dune sands, flat terrain, and plateau of Miocene limestones. It indicates that rainfall, geology, geomorphology, and soil significantly contribute to groundwater augmentation in the Kilinochchi district. The upper northwestern, middle and eastern parts of the study area (Karachchi DS division, Kandawalai DS division and Northern part of Poonakary DS division) generally have high groundwater potential due to high annual average rainfall (>106 mm), flat terrain with less than 0.5-degree slope, Alluvial and lagoonal clay, silt sand, and agricultural land. Moderate groundwater potential zones exist mainly in the west part and small patches in the central and eastern parts of the study area (Poonakary DS division). As a result of less annual average rainfall (<94 mm), red-yellow Latosols soil, upwarped Pleistocene coastal plain, red earth, red and brown sand, lithology with less permeability, the western part of the study area (Poonakary DS division) is dominated by low and shallow groundwater potential areas. Furthermore, the groundwater potential map shows that, in addition to the significant control of geology and rainfall, the distribution of groundwater is influenced by land use/land cover, geomorphology, and soil. In addition, the area is underlain by red earth, red and brown sand in the west part of the study area, characterized by relatively lower groundwater potential zones. However, this area comes under a moderate groundwater potential zone because of forests with a high infiltration rate.

Validation of the Groundwater Potentiality
Validation of the result is more important to have scientific significance [82,100]. Thus, during the pre-monsoon season between March 2020 and August 2020, a field survey was conducted to determine the water table depth throughout the study area. The stratified random sample was used to choose 79 wells, and the coordinates of those wells were collected using a portable GPS. In addition, the depth to the water level of 79 wells was measured in feet (later converted to meters). According to the survey, the depth of the well water ranged from 5.3 m to 19.2 m. The observed wells were classified into five groups in an equal interval based on well water depth [37], including very high groundwater potential (<7 m), high groundwater potential (7-10 m), moderate groundwater potential (10-13 m), low groundwater potential (13-17 m), and very low groundwater potential (<17 m). To check the accuracy of the map, the wells' water level was cross-checked against the prepared groundwater potential maps [75].
The wells' water depth data was used as a reference point to check the accuracy of delineated potential groundwater zones. The wells' water depth data was overlaid with the potential groundwater zones ( Figure 13) as applied in several studies [59,101]. According to the well water depth, the groundwater potentiality was very high in the area where well water depth was relatively shallow. Nine out of ten wells with less than seven meters of depth are in the very high groundwater potential zone, while one well is in the high groundwater potential zone. Twenty-nine of the thirty-nine wells with a depth of 7-10 m are in the high groundwater potential zone, while seven wells are in the moderate groundwater potential zone, and three wells are in the very high groundwater potential zone. Sixteen of the eighteen wells with a depth of 10-13 m are in the moderate groundwater potential zone, while two wells are in the low groundwater potential zone. Three of the four wells with depths of 13-17 m are in the low groundwater potential zone, while one is in the extremely low groundwater potential zone. Seven of eight wells with more than 17 m depth are in the low groundwater potential zone, whereas one well is in the high groundwater potential zone. The data found that sixty-four of the seventy-nine wells matched with potential groundwater zones. This suggests that 81 percent of the wells' depth to water is associated with the specified potential groundwater zones. It can be concluded that the model-generated groundwater potential zones were consistent with existing well water data. The ROC curve yielded a similar result.
The receiver operating characteristics (ROC) curve, which is a widely accepted technique for validating accuracy, was used to assess the accuracy of the model used [59,102,103]. The relation between the area under curve (AUC) and prediction accuracy can be summarized as poor (0.5-0.6); average (0.6-0.7); good (0.7-0.8); very good (0.8-0.9); and excellent (0.9-1.0) [4,82]. The Kilinochchi district's groundwater potential map has been validated by 79 wells (Figure 14). The true positive rate (sensitivity) is plotted to function the falsepositive rate in a ROC curve for varying cut-off points of a parameter. Each ROC curve point represents a pair of sensitivities, which corresponds to a certain decision threshold. According to the ROC graph, the area under the curve is measured and indicates an AUC value of 0.818, referring to 81.8% of the prediction accuracy ( Figure 14). Therefore, it can be implied that the methods used in this study exhibit an acceptable level of accuracy (AUC = 81.8%) in delineating potential groundwater zones. The findings show the capacity of RS-GIS and AHP techniques to determine possible groundwater zones, which will aid in determining the best places for groundwater extraction. The validation accuracy (81%) demonstrates that the methods and data used to delineate potential groundwater zones have produced accurate results by analyzing the extent of parameters' fitness and comparing the weight of relevant factors.

Conclusions
The integrated RS-GIS and AHP techniques help identify the potential groundwater zone in a given area and provide reliable and cost-effective preliminary information about groundwater resources. An integrated platform of RS, GIS, and AHP techniques was used to prepare the groundwater potential map of the Kilinochchi district. The AHP technique allocated thematic layers weighted for the following categories: rainfall, geology, geomorphology, soil, drainage density, linear density, slope, and land use cover. All thematic layers were integrated into ArcGIS 10.4.1 platform and generated a groundwater potential map. The resultant map has five categories, namely very high (111.26 km 2 ), high (507.74 km 2 ), moderate (309.89 km 2 ), low (207.78 km 2 ), and very low (59.12 km 2 ). The very high potential zone is located in the northeastern study area (Pachchilaipalli DS division), which is highly favorable for groundwater prospecting. Very low potential zones are mainly found in the extreme western part of the Poonakary DS division, which is the least favorable for groundwater prospecting. About 48% of the Kilinochchi district falls into moderate to very low groundwater potential zones that should require special actions to increase groundwater conditions. The overall result indicates that the groundwater of the Kilinochchi district is influenced mainly by rainfall, geology, and soil factors.
The ROC curve was eventually prepared to check the appropriateness of the approach used to delineate the potential groundwater zone. The validation result of GIS-based AHP indicates a reasonably good prediction accuracy of 81.8%. It can be implied that the methods used to delineate potential groundwater zones in the Kilinochchi district are reliable. The spatial distribution of the zones was highlighted through the investigation of groundwater potential in the Kilinochchi district. However, more research may be conducted on the quality and suitability of groundwater for many purposes, including drinking, agricultural, and industrial activities. Groundwater recharging has a significant impact on groundwater potential. As a result, a quantitative examination of groundwater recharge is recommended for future studies to empirically demonstrate the area's groundwater potential. This research will help policymakers better manage the Kilinochchi district's groundwater resources and give scope for further research into groundwater exploration in the area. Furthermore, previous research found that deforestation in Sri Lanka was more severe between 2010 and 2019, resulting in the conversion of 7597.9 ha of land into other landforms. As a result, it suggests that groundwater is becoming a more important source of water in Sri Lanka's tropical dry zone [104]. Hence, more research on groundwater potential covering Sri Lanka's entire tropical dry zone should be focused on in the future. The methodology, techniques, and results of the present study may be helpful to evaluate the potential groundwater zone in similar semi-arid drought-prone regions in Sri Lanka and around the world.
Author Contributions: The authors Vyddiyaratnam Pathmanandakumar and Nadarajapillai Thasarathan proposed the topic and spearheaded the data processing and analysis, as well as the writing of the manuscript; Manjula Ranagalage helped to edit the manuscript. All authors have read and agreed to the published version of the manuscript.