Electrically Switchable Semiloop Antenna with Polarization and Pattern Diversity

: This paper proposes a coplanar waveguide (CPW)-fed semiloop antenna with switchable linear polarization and radiation pattern. This design uses a novel asymmetric coplanar strip line (ACPS) circular ring to produce even or odd modes of the CPW, which can generate vertical or horizontal polarization in the semiloop antenna. The modes of the ACPS circular ring can be switched by controlling the on / o ﬀ state of the PIN diode, and only a two-bit control signal is required to select the operating mode. The proposed polarization switchable antenna uses only one metal layer of the printed circuit board. The center frequency of the dual-polarization antenna was determined to be 2.45 GHz, and the − 10 dB impedance bandwidths were determined to be 12.86% and 4.92% for vertical and horizontal polarization, respectively. The antenna parameters, such as the return loss, gain, and radiation patterns, are also presented for validating the proposed design.

Isolation between the two feed ports is a big issue and the antenna performance is sensitive to the ground plane size.
In this paper, a novel polarization reconfigurable semiloop antenna with only one metal layer is proposed. To the best of our knowledge, this is the first polarization/pattern switchable antenna that is realized using only one metal layer. Unlike the popularly used patch or crossed dipole structure, this design presents a new semiloop structure to produce two orthogonal linear polarizations with pattern diversity. In addition, a novel asymmetric coplanar strip line (ACPS) ring structure is proposed to switch modes on CPW. This design has one CPW feed port, whose polarization state can be electrically switched between vertical and horizontal polarization through a 2-bit control signal. The proposed antenna can be easily fabricated using printed circuit board (PCB) technology, and it requires only two surface-mount PIN diodes and one capacitor. Compared with the linear polarization switchable antennas found in the literature [23][24][25][26][27][28]30,31], the proposed design has a relatively compact radiating element and uses a planar transmission line feed configuration. Moreover, the resonant frequencies of the two orthogonally polarized waves can be easily adjusted to the same frequency. The low-cost and planar design of the proposed antenna renders it suitable for modern wireless communication systems. Design of the semiloop antenna and the electrically switchable circuit are presented in Sections 2.1 and 2.2, respectively. Results are presented in Section 3. Finally, conclusions are presented in Section 4. The antenna design comprises three parts, namely the CPW, an asymmetric coplanar strip line (ACPS) circular ring, and a rectangular semiloop radiating structure. The bottom edge of the rectangular semiloop antenna is a 100-Ω ACPS transmission line structure, which is not a part of the resonator. Figure 1b presents the layout of the structure from the CPW to the ACPS. The optimized antenna dimensions are shown in Table 1.

Antenna Structure
The simulated insertion loss displayed in Figure 2 indicates that the power input from port 1 was equally divided into ports 2 and 3, and only a 0.25 dB loss was observed. Two inverted L monopole antennas were installed on ports 2 and 3, where their open ends were connected together to form a rectangular loop structure. Since the bottom edge of the rectangular loop is not a part of the antenna, the structure is called a semiloop antenna.
The CPW-fed rectangular semiloop antenna has two radiation modes according to the modes of the CPW. If the CPW operates in the even mode, the vector current distribution in the rectangular semiloop antenna is symmetric with respect to the x-axis. Therefore, the semiloop antenna is equivalent to two vertically polarized monopole antennas spaced at approximately half the wavelength and having equal phase and amplitude. The maximum radiated power can be found in the +z/−z direction, and the nulls can be found in the +x/−x direction. However, if the CPW is in the odd mode and fed to the semiloop antenna, the currents on the two short sides of the rectangular semiloop antenna are in opposite directions, whereas the currents are in the same direction on the long side. Therefore, a horizontally polarized dipole antenna can be generated. The radiation patterns of the two modes are complementary, and providing two orthogonal linear polarization states in the +z/−z direction.

Even Mode/Odd Mode Switching Circuit
A CPW generally operates in the even mode. To switch antenna polarization, a circular ring made of an ACPS was fabricated for switching the CPW mode electrically. Figure 3a illustrates the geometry of the circular ring, which was made of a 100-Ω ACPS. There existed two diodes on this structure. The first diode (called diode A) was placed at the 12 o'clock position, which connected the ACPS ring and output CPW. The other diode (called diode B) was placed at approximately the 5 o'clock position, which connected the ACPS ring and ground plane. The diode used in this design was BAR64-02V, Figure 4 shows the equivalent circuit models of the diode when it was in the ON state and OFF state, which was employed in the simulation. Component values were chosen according to the datasheet [32]. As shown in Figure 1a, diode A was biased through Pad A and Pad B; diode B was biased through Pad B and Pad C (ground). Each pad had a series chip inductor of 22 nH to block RF signal passing through the bias line. When diode A was on (short circuited) and diode B was off (open circuited), the input power symmetrically passed through the left-hand side and right-hand side of the ACPS ring and then to the CPW output port through diode A. Therefore, as shown in Figure 3b, a normal even mode was produced on the output CPW. Since the characteristic impedance of the two current paths was 100 Ω, the resultant input impedance was 50 Ω. By contrast, when diode A was off (open circuited) and diode B was on (short circuited), the current only passes through the left-hand side of the ACPS ring and to the CPW output port by electromagnetic coupling. In this case, the odd mode was generated on the output CPW, as presented in Figure 3c. Since the electrical length of the current path was approximately half the wavelength at 2.45 GHz, the ACPS did not affect the input impedance. The circumference of the ACPS ring and position of diode B could be used to adjust the impedance matching of the feeding network when the network was used to excite the odd mode of the CPW. The relations among the bias voltage, diode states, and antenna polarizations are listed in Table 2.

Even Mode/Odd Mode Switching Circuit
A CPW generally operates in the even mode. To switch antenna polarization, a circular ring made of an ACPS was fabricated for switching the CPW mode electrically. Figure 3a illustrates the geometry of the circular ring, which was made of a 100-Ω ACPS. There existed two diodes on this structure. The first diode (called diode A) was placed at the 12 o'clock position, which connected the ACPS ring and output CPW. The other diode (called diode B) was placed at approximately the 5 o'clock position, which connected the ACPS ring and ground plane. The diode used in this design was BAR64-02V, Figure 4 shows the equivalent circuit models of the diode when it was in the ON state and OFF state, which was employed in the simulation. Component values were chosen according to the datasheet [32]. As shown in Figure 1a, diode A was biased through Pad A and Pad B; diode B was biased through Pad B and Pad C (ground). Each pad had a series chip inductor of 22 nH to block RF signal passing through the bias line. When diode A was on (short circuited) and diode B was off (open circuited), the input power symmetrically passed through the left-hand side and right-hand side of the ACPS ring and then to the CPW output port through diode A. Therefore, as shown in Figure 3b, a normal even mode was produced on the output CPW. Since the characteristic impedance of the two current paths was 100 Ω, the resultant input impedance was 50 Ω. By contrast, when diode A was off (open circuited) and diode B was on (short circuited), the current only passes through the left-hand side of the ACPS ring and to the CPW output port by electromagnetic coupling. In this case, the odd mode was generated on the output CPW, as presented in Figure 3c. Since the electrical length of the current path was approximately half the wavelength at 2.45 GHz, the ACPS did not affect the input impedance. The circumference of the ACPS ring and position of diode B could be used to adjust the impedance matching of the feeding network when the network was used to excite the odd mode of the CPW. The relations among the bias voltage, diode states, and antenna polarizations are listed in Table 2.      Figure 5a,b displays the simulated current distribution when the CPW of the proposed antenna operated in the even and odd modes, respectively. When diode A was on and diode B was off, the even mode of the CPW was excited, which generated vertical polarization on the semiloop antenna. As shown in Figure 5a, a current null could be found in the center of the semiloop antenna. By contrast, when diode A was off and diode B was on, the CPW produced an odd mode and generated horizontal polarization on the semiloop antenna. In this case, two current nulls could be found on the short edge of the semiloop antenna, as depicted in Figure 5b. The parameters W and L determine the resonant frequencies of the vertical and horizontal polarized modes, respectively. Finally, the optimized values of W and vl were W = 42 mm and vl = 16.8 mm. Figure 6 shows the fabricated prototype of the proposed antenna. As shown in the figure, Diode A was biased through the blue wire and the red wire, while Diode B was biased through the red wire and the yellow wire. The DC switch control voltage was obtained by a battery, which provided a large current of about 10 mA to ensure the AC resistance was low. The measured and simulated reflection coefficients of the proposed antenna are depicted in Figure 7. The red line represents the reflection coefficient when the antenna operated in the even mode (vertical polarization mode), whereas the blue line represents the simulation reflection coefficient when the antenna operated in the odd mode (horizontal polarization mode). The resonant frequencies of the two polarization modes were both approximately 2.45 GHz. The achieved −10 dB impedance bandwidths covering the two operation modes were 4.92% (121 MHz) for the vertical and horizontal polarized modes.

Measurement and Simulation Results
The fabricated prototype was also tested in an anechoic chamber. Figures 8 and 9 present the measured and simulated radiation patterns when the antenna operates in vertical polarization mode and horizontal polarization mode, respectively. The measured antenna gain at +Z direction was approximately 2.62 dBi for vertical polarization, while it was approximately 3.37 dBi for horizontal polarization. The simulated radiation efficiency for vertical polarization and horizontal polarization were 84.9% and 78.2%, respectively, where the parasitic effects of the PIN diodes shown in Figure 4 was taken into account. The measured and simulated results were in good agreement, the experimental verification of the proposed design shown that good polarization purity was obtained. Table 3 gives a comparison between the proposed antenna and other polarization reconfigurable antennas. From this table, it can be seen that the proposed antenna provided both polarization and pattern diversities in a smaller size with a switching circuit included, and used less diodes. The  Figure 5a,b displays the simulated current distribution when the CPW of the proposed antenna operated in the even and odd modes, respectively. When diode A was on and diode B was off, the even mode of the CPW was excited, which generated vertical polarization on the semiloop antenna. As shown in Figure 5a, a current null could be found in the center of the semiloop antenna. By contrast, when diode A was off and diode B was on, the CPW produced an odd mode and generated horizontal polarization on the semiloop antenna. In this case, two current nulls could be found on the short edge of the semiloop antenna, as depicted in Figure 5b. The parameters W and L determine the resonant frequencies of the vertical and horizontal polarized modes, respectively. Finally, the optimized values of W and vl were W = 42 mm and vl = 16.8 mm.   Figure 6 shows the fabricated prototype of the proposed antenna. As shown in the figure, Diode A was biased through the blue wire and the red wire, while Diode B was biased through the red wire and the yellow wire. The DC switch control voltage was obtained by a battery, which provided a large current of about 10 mA to ensure the AC resistance was low. The measured and simulated reflection coefficients of the proposed antenna are depicted in Figure 7. The red line represents the reflection coefficient when the antenna operated in the even mode (vertical polarization mode), whereas the blue line represents the simulation reflection coefficient when the antenna operated in the odd mode (horizontal polarization mode). The resonant frequencies of the two polarization modes were both approximately 2.45 GHz. The achieved −10 dB impedance bandwidths covering the two operation modes were 4.92% (121 MHz) for the vertical and horizontal polarized modes.           The fabricated prototype was also tested in an anechoic chamber. Figures 8 and 9 present the measured and simulated radiation patterns when the antenna operates in vertical polarization mode and horizontal polarization mode, respectively. The measured antenna gain at +Z direction was approximately 2.62 dBi for vertical polarization, while it was approximately 3.37 dBi for horizontal polarization. The simulated radiation efficiency for vertical polarization and horizontal polarization were 84.9% and 78.2%, respectively, where the parasitic effects of the PIN diodes shown in Figure 4 was taken into account. The measured and simulated results were in good agreement, the experimental verification of the proposed design shown that good polarization purity was obtained. Table 3 gives a comparison between the proposed antenna and other polarization reconfigurable antennas. From this table, it can be seen that the proposed antenna provided both polarization and pattern diversities in a smaller size with a switching circuit included, and used less diodes. The reduction in antenna gain might be attributed to the small resonator size due to electromagnetic physics.

Conclusions
This paper proposed a novel electrically reconfigurable semiloop antenna. It utilized a novel planar ACPS circular ring to change the modes of the CPW used to feed the semiloop antenna. The novel semiloop structure generated two orthogonal linear polarizations where the resonant

Conclusions
This paper proposed a novel electrically reconfigurable semiloop antenna. It utilized a novel planar ACPS circular ring to change the modes of the CPW used to feed the semiloop antenna. The novel semiloop structure generated two orthogonal linear polarizations where the resonant

Conclusions
This paper proposed a novel electrically reconfigurable semiloop antenna. It utilized a novel planar ACPS circular ring to change the modes of the CPW used to feed the semiloop antenna. The novel semiloop structure generated two orthogonal linear polarizations where the resonant frequencies of the two modes could be adjusted individually. In addition, this antenna element occupied a small footprint as compared to the popularly used patch, crossed-dipole, or crossed-slot design, over 40% dimension was saved. The proposed antenna required only one metal layer of a PCB including the switching circuit. The center frequency of the dual-polarization antenna was determined to be 2.45 GHz, and very low cross polarization was obtained.
This design provided switchable linear polarization in the +z/−z direction. It also could be used as a pattern diversity antenna because the achieved radiation patterns of the two modes were complementary. For the application of wireless local area network, if the antenna operated in the vertical polarization mode, the antenna provided the broadest coverage areas horizontally on the same floor. However, if the coverage needs to be increased to accommodate more users on the floors above and below, this antenna can be switched to horizontal polarization mode to provide greater vertical coverage.
The proposed design is planar, single layered, and easily be fabricated. Compared with polarization switchable antennas found in the literature, the proposed design is more suitable for integration with radio-frequency circuits and thin film printed circuit board.