Investigation of Electrical Contacts to p-Grid in SiC Power Devices Based on Charge Storage E ﬀ ect and Dynamic Degradation

: P-grid is a typical feature in power devices to block high o ﬀ -state voltage. In power devices, the p-grid is routinely coupled to an external electrode with an Ohmic contact, but Schottky contact to the p-grid is also proposed / adopted for certain purposes. This work investigates the role of contact to p-grid in power devices based on the commonly adopted technology computer-aided design (TCAD) device simulations, with the silicon carbide (SiC) junction barrier Schottky (JBS) diode as a case study. The static characteristics of the JBS diode is independent of the nature of the contact to p-grid, including the forward voltage drop ( V F ) and the breakdown voltage ( BV ). However, during the switching process, a Schottky contact would cause storage of negative charges in the p-grid, which leads to an increased V F during switching operation. On the contrary, an Ohmic contact provides an e ﬀ ective discharging path for the stored negative charges in the p-grid, which eliminates the dynamic degradation issues. Therefore, the necessity of an Ohmic contact to p-grid in power devices is clariﬁed.


Introduction
Power devices typically feature p-grids inside the device active regions to block the high off-state voltage or to protect certain vulnerable structures [1]. With the key challenges, such as low channel resistance [2], channel mobility [3,4], and oxide reliability [5] being addressed, silicon carbide (SiC) devices are now commercially available from several vendors [6,7]. The SiC devices are widely used in power electronics-for example, SiC transistors adopted as switches in inverter circuit, SiC diodes used in rectifier circuit and as a freewheeling diode in inverter circuit. In a power metal-oxide-semiconductor field-effect transistor (MOSFET), the p-grid is grounded to the source electrode, while in a junction barrier Schottky (JBS) diode, the p-grid is connected to the anode. In blocking state, the PN junction (between p-grid and n-drift region) is reversely biased to withstand the high voltage. In power devices, the metal contact to the p-grid is mostly an Ohmic contact. However, Schottky contact is also proposed and adopted for certain purposes. For example, for an insulated gate bipolar transistor (IGBT), a Schottky contact to the p-body has been proposed to enhance the minority carrier concentration near the emitter side without any sacrifice in the off-state breakdown voltage (BV) [8]. In the emerging gallium nitride (GaN) power transistors, a Schottky contact to the p-region is widely used to enlarge the gate voltage swing [9,10], or explored as a method to adjust the threshold voltage [11,12]. Furthermore, the injection of minority carrier through the PN junction is likely to cause bipolar degradation in SiC power devices, such as body diodes of SiC MOSFETs [13,14] and SiC bipolar junction transistor (BJT) [15]. If the metal contact to p-grid is non-Ohmic-e.g., a Schottky contact is used insteadthe conduction through the PN junction can be completely suppressed, so the bipolar degradation and poor reverse recovery can be avoided [16,17].
This work aims to discuss the role of the contact to p-grid in certain power devices, whose metal/p-region contacts are under investigation. The SiC JBS diode is adopted in this work as a case study. SiC power devices have attracted worldwide attention because of the high critical breakdown field in SiC [18]-for example, SiC MOSFET with protruded p-base [19], split-gate SiC MOSFET [20], SiC diodes [21], and GaN/SiC hybrid field-effect transistors [22]. In this work, we present that the contact to the p-grid exerts little influence on the static characteristics of the SiC JBS diode, including the forward voltage drop (V F ) and the BV. However, the SiC JBS diode with Schottky contact to the p-grid suffers from severely degraded dynamic V F during the switching operation. The cause of the dynamic degradation is found to be the charge storage in the p-grid. An Ohmic contact to the p-grid effectively discharges the p-grid and eliminates the dynamic degradation.
Technology computer-aided design (TCAD) Sentaurus device simulations and mixed mode simulations are deployed to reveal the internal dynamics of the devices. A Sentaurus Structure Editor is used for structure and mesh construction. A Sentaurus Device is used for device simulations and mixed-mode circuit simulations. The physics models such as Auger and Shockley-Reed-Hall combination, impact ionization (Lackner model), incomplete ionization, high-field saturation effects, doping dependent transport, band narrowing, and anisotropic mobility model are all considered. Figure 1 shows the schematic structures of SiC JBS diodes with either an Ohmic contact or a Schottky contact to the p-grid. The work function of the Schottky contact is assumed to be 4.33 eV. The n-drift region has a thickness of 12 µm, and a doping concentration of 8 × 10 15 cm −3 . The width of the p-grid in one cell is W grid = 2 µm. The width of the junction gate field-effect transistor (JFET) region is W JFET = 2 µm unless otherwise specified. The key device parameters of the diodes are listed in Table 1. The temperature is set as room temperature (300 K) in the following TCAD simulations.

Device Structure and Static Characteristics
Electronics 2020, 9, x FOR PEER REVIEW 2 o In the emerging gallium nitride (GaN) power transistors, a Schottky contact to the p-region is wide used to enlarge the gate voltage swing [9,10], or explored as a method to adjust the threshold voltag [11,12]. Furthermore, the injection of minority carrier through the PN junction is likely to cau bipolar degradation in SiC power devices, such as body diodes of SiC MOSFETs [13,14] and Si bipolar junction transistor (BJT) [15]. If the metal contact to p-grid is non-Ohmic-e.g., a Schottk contact is used instead-the conduction through the PN junction can be completely suppressed, s the bipolar degradation and poor reverse recovery can be avoided [16,17]. This work aims to discuss the role of the contact to p-grid in certain power devices, whos metal/p-region contacts are under investigation. The SiC JBS diode is adopted in this work as a ca study. SiC power devices have attracted worldwide attention because of the high critical breakdow field in SiC [18]-for example, SiC MOSFET with protruded p-base [19], split-gate SiC MOSFET [20 SiC diodes [21], and GaN/SiC hybrid field-effect transistors [22]. In this work, we present that th contact to the p-grid exerts little influence on the static characteristics of the SiC JBS diode, includin the forward voltage drop (VF) and the BV. However, the SiC JBS diode with Schottky contact to th p-grid suffers from severely degraded dynamic VF during the switching operation. The cause of th dynamic degradation is found to be the charge storage in the p-grid. An Ohmic contact to the p-gr effectively discharges the p-grid and eliminates the dynamic degradation.
Technology computer-aided design (TCAD) Sentaurus device simulations and mixed mod simulations are deployed to reveal the internal dynamics of the devices. A Sentaurus Structure Edito is used for structure and mesh construction. A Sentaurus Device is used for device simulations an mixed-mode circuit simulations. The physics models such as Auger and Shockley-Reed-Ha combination, impact ionization (Lackner model), incomplete ionization, high-field saturation effect doping dependent transport, band narrowing, and anisotropic mobility model are all considered. Figure 1 shows the schematic structures of SiC JBS diodes with either an Ohmic contact or Schottky contact to the p-grid. The work function of the Schottky contact is assumed to be 4.33 eV The n-drift region has a thickness of 12 µm, and a doping concentration of 8 × 10 15 cm −3 . The width the p-grid in one cell is Wgrid = 2 µm. The width of the junction gate field-effect transistor (JFET) regio is WJFET = 2 µm unless otherwise specified. The key device parameters of the diodes are listed in Table  The temperature is set as room temperature (300 K) in the following TCAD simulations.   The static I-V characteristics of the SiC JBS diodes are plotted in Figure 2. The property of the contact to the p-grid in the SiC JBS diode (whether it is an Ohmic contact or a Schottky contact) does not affect the static I-V characteristics. In the forward conduction, the current mainly flows through the metal/n-drift Schottky contact, while the PN junction does not participate in the forward conduction in normal operation condition. The forward voltage drops (V F , defined at 200 A/cm 2 in this paper) of the two JBS diodes are both 1.1 V. With a sufficiently high voltage applied to the JBS diode with an Ohmic contact to the p-grid, the PN junctions between p-grids and n-drift region would be turned on and contribute to the forward conduction (not shown). When the SiC material contains basal plane dislocations, the bipolar conduction through the PN junction would lead to bipolar degradation, as manifested by a shift in V F and an increase in reverse leakage current [13,14]. For the JBS diode with Schottky contact to the p-grid, the bipolar conduction through the PN junction is suppressed by the reversely biased metal/p-grid Schottky junction even at a very high forward voltage drop [10,16]. The static I-V characteristics of the SiC JBS diodes are plotted in Figure 2. The property of the contact to the p-grid in the SiC JBS diode (whether it is an Ohmic contact or a Schottky contact) does not affect the static I-V characteristics. In the forward conduction, the current mainly flows through the metal/n-drift Schottky contact, while the PN junction does not participate in the forward conduction in normal operation condition. The forward voltage drops (VF, defined at 200 A/cm 2 in this paper) of the two JBS diodes are both 1.1 V. With a sufficiently high voltage applied to the JBS diode with an Ohmic contact to the p-grid, the PN junctions between p-grids and n-drift region would be turned on and contribute to the forward conduction (not shown). When the SiC material contains basal plane dislocations, the bipolar conduction through the PN junction would lead to bipolar degradation, as manifested by a shift in VF and an increase in reverse leakage current [13,14]. For the JBS diode with Schottky contact to the p-grid, the bipolar conduction through the PN junction is suppressed by the reversely biased metal/p-grid Schottky junction even at a very high forward voltage drop [10,16].

Device Structure and Static Characteristics
The breakdown voltage of the JBS diodes is not affected by the property of the contact to p-grid, either. For the JBS diode with Schottky contact to p-grid, the metal/p-grid Schottky junction is forwardly biased, and the p-grid is virtually shorted to the anode in this condition. Thus, for both the two JBS diodes, the PN junctions between p-grids and n-drift region are reversely biased to support the high off-state voltage.

Switching Performances
In real applications, the power devices are usually operated in switching mode. Therefore, the switching performances of the studied SiC JBS diodes are critical. In this paper, the test circuit in Figure 3a is adopted to study the switching properties of the SiC JBS diodes [23,24]. The studied SiC JBS diode is the device under test (DUT). The area of the studied SiC JBS diode is 1 cm 2 . A stray inductance of 10 nH is assumed in the loop. A MOSFET is used as the switch for the circuit. The supply voltage is 800 V and the load current is 200 A. When the MOSFET in the circuit is turned-on, the current of the MOSFET increases to 200 A. Then, when the MOSFET is turned-off, the current of the MOSFET decreases and the current of the DUT increases because the current of the inductor L is The breakdown voltage of the JBS diodes is not affected by the property of the contact to p-grid, either. For the JBS diode with Schottky contact to p-grid, the metal/p-grid Schottky junction is forwardly biased, and the p-grid is virtually shorted to the anode in this condition. Thus, for both the two JBS diodes, the PN junctions between p-grids and n-drift region are reversely biased to support the high off-state voltage.

Switching Performances
In real applications, the power devices are usually operated in switching mode. Therefore, the switching performances of the studied SiC JBS diodes are critical. In this paper, the test circuit in Figure 3a is adopted to study the switching properties of the SiC JBS diodes [23,24]. The studied SiC JBS diode is the device under test (DUT). The area of the studied SiC JBS diode is 1 cm 2 . A stray inductance of 10 nH is assumed in the loop. A MOSFET is used as the switch for the circuit. The supply voltage is 800 V and the load current is 200 A. When the MOSFET in the circuit is turned-on, the current of the MOSFET increases to 200 A. Then, when the MOSFET is turned-off, the current of the MOSFET Electronics 2020, 9, 1723 4 of 9 decreases and the current of the DUT increases because the current of the inductor L is not changed. In this period, the turning-on transient of the DUT can be studied. After the DUT is fully turned-on and works for a while, the DUT current will decrease when the MOSFET is turned-on again. Hence, the turning-off transient of the DUT can be studied when the MOSFET is turned-on.
Electronics 2020, 9, x FOR PEER REVIEW 4 of 9 not changed. In this period, the turning-on transient of the DUT can be studied. After the DUT is fully turned-on and works for a while, the DUT current will decrease when the MOSFET is turned-on again. Hence, the turning-off transient of the DUT can be studied when the MOSFET is turned-on.  Figure 3b shows the turn-off transient of the SiC JBS diodes. The MOSFET is turned on at t = 0 ns. Thus, the diodes are turned off and start to sustain the 800-V reverse voltage. For the SiC JBS diode with Ohmic contact to p-grid, the high reverse voltage is biased on the internal PN junction. For the SiC JBS diode with Schottky contact to p-grid, the p-grid to anode voltage (Vp-A, defined as the voltage difference between p-grid and the anode) is clamped to ~1.7 V, near the turn-on voltage of the Schottky diode. Therefore, the off-state voltage is sustained by the PN junction inside the SiC JBS diodes, irrespective of the property of the contact to the p-grid.
When the SiC MOSFET is turned off, the SiC JBS diode is rendered into on-state, as shown in Figure 3c. The voltage across the PN junction inside the SiC JBS diode quickly drops, and then stabilizes at a forward voltage. The forward voltage of the JBS diode with an Ohmic contact to p-grid recovers to near its static value, 1.1 V. However, as to the JBS diode with a Schottky contact to p-grid, the forward voltage is almost 5 V, which is much larger than the static forward voltage shown in Figure 2. The static forward voltages of both the JBS diodes are only 1.1 V in Figure 2.
From Figure 3c, it is found the p-grid to anode voltage Vp-A is highly negative (~−17 V) after about 180 ns in the JBS diode with a Schottky contact to p-grid, which is very different to the JBS diode with  Figure 3b shows the turn-off transient of the SiC JBS diodes. The MOSFET is turned on at t = 0 ns. Thus, the diodes are turned off and start to sustain the 800-V reverse voltage. For the SiC JBS diode with Ohmic contact to p-grid, the high reverse voltage is biased on the internal PN junction. For the SiC JBS diode with Schottky contact to p-grid, the p-grid to anode voltage (V p-A , defined as the voltage difference between p-grid and the anode) is clamped to~1.7 V, near the turn-on voltage of the Schottky diode. Therefore, the off-state voltage is sustained by the PN junction inside the SiC JBS diodes, irrespective of the property of the contact to the p-grid.
When the SiC MOSFET is turned off, the SiC JBS diode is rendered into on-state, as shown in Figure 3c. The voltage across the PN junction inside the SiC JBS diode quickly drops, and then stabilizes at a forward voltage. The forward voltage of the JBS diode with an Ohmic contact to p-grid recovers to near its static value, 1.1 V. However, as to the JBS diode with a Schottky contact to p-grid, the forward Electronics 2020, 9, 1723 5 of 9 voltage is almost 5 V, which is much larger than the static forward voltage shown in Figure 2. The static forward voltages of both the JBS diodes are only 1.1 V in Figure 2.
From Figure 3c, it is found the p-grid to anode voltage V p-A is highly negative (~−17 V) after about 180 ns in the JBS diode with a Schottky contact to p-grid, which is very different to the JBS diode with Ohmic contact to p-grid where the V p-A is 0. This phenomenon helps to explain the higher forward voltage V of almost 5 V in the JBS diode with a Schottky contact to p-grid, as the negative V p-A of about −17 V suggests widened depletion region into n-drift region around the p-grid.
To confirm the above observed dynamic behavior of the studied SiC JBS diodes, Figure 4 shows the I-V characteristics of the JBS diodes before and after an 800-V reverse bias stress. For the JBS diode with an Ohmic contact to p-grid, the I-V characteristics after the 800-V stress are nearly the same as the initial fresh state. However, for the JBS diode with Schottky contact to p-grid, the I-V characteristic after an 800-V stress is severely degraded. The results in Figure 4 agree with the switching performance in Figure 3, confirming a degradation of dynamic V F in the SiC JBS diode with a Schottky contact to p-grid.
Electronics 2020, 9, x FOR PEER REVIEW 5 of 9 Ohmic contact to p-grid where the Vp-A is 0. This phenomenon helps to explain the higher forward voltage V of almost 5 V in the JBS diode with a Schottky contact to p-grid, as the negative Vp-A of about −17 V suggests widened depletion region into n-drift region around the p-grid. To confirm the above observed dynamic behavior of the studied SiC JBS diodes, Figure 4 shows the I-V characteristics of the JBS diodes before and after an 800-V reverse bias stress. For the JBS diode with an Ohmic contact to p-grid, the I-V characteristics after the 800-V stress are nearly the same as the initial fresh state. However, for the JBS diode with Schottky contact to p-grid, the I-V characteristic after an 800-V stress is severely degraded. The results in Figure 4 agree with the switching performance in Figure 3, confirming a degradation of dynamic VF in the SiC JBS diode with a Schottky contact to p-grid.   Figure 5a shows the waveform of the voltage on the SiC JBS diode with a Schottky contact to p-grid for the dynamic simulations. Figure 5b shows the electron distribution inside the SiC JBS diode with a Schottky contact to p-grids. In the initial equilibrium state, there is only a narrow depletion region around the p-grid and under the anode metal. The device is then stressed with a reverse bias of 800 V. As shown in the stressing state of the SiC JBS diode with a Schottky contact to p-grids, the n-drift region in the device is depleted to support the reverse bias. In the reverse biased state, the n-drift region is depleted to form a positive space charge region to support the high voltage, and there must be equal negative charges to pair the positive charges in the depleted n-drift region. These negative charges are located partially in the anode metal, and partially in the p-grid. Then, in the stressed state of the SiC JBS diode with a Schottky contact to p-grids, the device returns to zero biased state. The p-grid cannot be effectively discharged since the discharging current path is blocked by the reversely biased metal/p-grid Schottky junction. The pgrid becomes virtually a floating region [25,26]. Therefore, the negative charges are stored in the pgrid. To keep an equilibrium state, the depletion region around p-grid is widened for more positive charges. As the n-drift region between p-grids is depleted, the forward voltage under stressed state has to be much larger than the forward voltage in initial state to keep the same forward current. This  Figure 5 reveals the physical mechanism of the observed dynamic behaviors in the SiC JBS diode with a Schottky contact to p-grid. Figure 5a shows the waveform of the voltage on the SiC JBS diode with a Schottky contact to p-grid for the dynamic simulations. Figure 5b shows the electron distribution inside the SiC JBS diode with a Schottky contact to p-grids. In the initial equilibrium state, there is only a narrow depletion region around the p-grid and under the anode metal. The device is then stressed with a reverse bias of 800 V. As shown in the stressing state of the SiC JBS diode with a Schottky contact to p-grids, the n-drift region in the device is depleted to support the reverse bias. In the reverse biased state, the n-drift region is depleted to form a positive space charge region to support the high voltage, and there must be equal negative charges to pair the positive charges in the depleted n-drift region. These negative charges are located partially in the anode metal, and partially in the p-grid. Then, in the stressed state of the SiC JBS diode with a Schottky contact to p-grids, the device returns to zero biased state. The p-grid cannot be effectively discharged since the discharging current path is blocked by the reversely biased metal/p-grid Schottky junction. The p-grid becomes virtually a Electronics 2020, 9, 1723 6 of 9 floating region [25,26]. Therefore, the negative charges are stored in the p-grid. To keep an equilibrium state, the depletion region around p-grid is widened for more positive charges. As the n-drift region between p-grids is depleted, the forward voltage under stressed state has to be much larger than the forward voltage in initial state to keep the same forward current. This explains the above different forward I-V characteristics before and after stress.
Electronics 2020, 9, x FOR PEER REVIEW 6 of 9 Figure 5c displays the electron distribution inside the SiC JBS diode with an Ohmic contact to pgrids for comparison. The initial and stressed states have the same electron distribution, which is different to that in Figure 5b. This verifies charge storage effect does not exist in the SiC JBS diode with an Ohmic contact to p-grids.  Figure 6 uses an equivalent circuit model to illustrate the charges storage mechanism in the p-grid of the SiC JBS diode with Schottky contact to p-grid. The diode terminal capacitance consists of metal/n-drift capacitance Cm and p-grid/n-drift capacitance Cp. In additional, the Schottky contact and p-grid constitute a Schottky diode Dp. When the JBS diode is rendered to reversely biased state, Dp is forwardly biased, and thus, both Cm and Cp can be effectively charged. The amount of charges built up across Cp is: where V is the voltage applied on JBS diode, εs is dielectric constant of SiC, WD is the depletion width of p-grid and n-drift junction, Vbi is the built-in potential, and N is the doping density of n-drift region. The negative portion of the charges is located inside the p-grid. When the JBS diode is turned to forward state, Dp blocks the discharging current from the anode of the JBS diode to Cp. Therefore, the negative charges are stored in the p-grid (i.e., the node between Cp and Dp in the equivalent circuit).
The difference between the initial VF (VF-init) and the stressed VF (VF-stre) of the SiC JBS diode with Schottky contact to p-grid is influenced by the WJFET. As shown in Figure 7, when WJFET is larger, both VF-init and VF-stre become smaller, and their difference is reduced. Theoretically, when WJFET is much larger than the depletion region around the p-grid, the VF-stre would become the same as VF-init.  Figure 5c displays the electron distribution inside the SiC JBS diode with an Ohmic contact to p-grids for comparison. The initial and stressed states have the same electron distribution, which is different to that in Figure 5b. This verifies charge storage effect does not exist in the SiC JBS diode with an Ohmic contact to p-grids. Figure 6 uses an equivalent circuit model to illustrate the charges storage mechanism in the p-grid of the SiC JBS diode with Schottky contact to p-grid. The diode terminal capacitance consists of metal/n-drift capacitance C m and p-grid/n-drift capacitance C p . In additional, the Schottky contact and p-grid constitute a Schottky diode D p . When the JBS diode is rendered to reversely biased state, D p is forwardly biased, and thus, both C m and C p can be effectively charged. The amount of charges built up across C p is: where the capacitance C p is [27]: where V is the voltage applied on JBS diode, ε s is dielectric constant of SiC, W D is the depletion width of p-grid and n-drift junction, V bi is the built-in potential, and N is the doping density of n-drift region.
electric filed at the Schottky contact (EJ) when sustaining the high off-state voltage. This means that a large WJFET makes the JBS diode more Schottky barrier diode (SBD)-like [28,29]. The large EJ is undesirable regarding leakage current and reliability [30]. The trade-off between Schottky junction field EJ (at the middle of Schottky contact between p-grids) in off-state and the VF of the SiC JBS diode with Schottky contact to p-grid is shown in Figure 7. The figure indicates that increasing the WJFET cannot eliminate the dynamic dispersion of VF. Therefore, an Ohmic contact to p-grid is required in SiC JBS diode.

Conclusions
This work reveals the significance of the property of electrical contact to p-grid in power devices. The silicon carbide (SiC) junction barrier Schottky (JBS) diode, which is widely used in power circuits, is adopted in this paper as a case study. The property of the contact to p-grid (whether it is a Schottky contact or an Ohmic contact) does not affect the static characteristics of the JBS diodes; however, the dynamic forward voltage drop (VF) of the JBS diode with a Schottky contact to p-grid is enlarged. This phenomenon is explained by the charge storage in the p-grid. The rectifying Schottky contact allows the charging of p-grid in reverse bias state, but it hinders the discharging of p-grid after the The negative portion of the charges is located inside the p-grid. When the JBS diode is turned to forward state, D p blocks the discharging current from the anode of the JBS diode to C p . Therefore, the negative charges are stored in the p-grid (i.e., the node between C p and D p in the equivalent circuit).
The difference between the initial V F (V F-init ) and the stressed V F (V F-stre ) of the SiC JBS diode with Schottky contact to p-grid is influenced by the W JFET . As shown in Figure 7, when W JFET is larger, both V F-init and V F-stre become smaller, and their difference is reduced. Theoretically, when W JFET is much larger than the depletion region around the p-grid, the V F-stre would become the same as V F-init . However, with a large W JFET , the screening effect of the p-grid becomes weak, which results in a higher electric filed at the Schottky contact (E J ) when sustaining the high off-state voltage. This means that a large W JFET makes the JBS diode more Schottky barrier diode (SBD)-like [28,29]. The large E J is undesirable regarding leakage current and reliability [30]. The trade-off between Schottky junction field E J (at the middle of Schottky contact between p-grids) in off-state and the V F of the SiC JBS diode with Schottky contact to p-grid is shown in Figure 7. The figure indicates that increasing the W JFET cannot eliminate the dynamic dispersion of V F . Therefore, an Ohmic contact to p-grid is required in SiC JBS diode.
Electronics 2020, 9, x FOR PEER REVIEW 7 of 9 However, with a large WJFET, the screening effect of the p-grid becomes weak, which results in a higher electric filed at the Schottky contact (EJ) when sustaining the high off-state voltage. This means that a large WJFET makes the JBS diode more Schottky barrier diode (SBD)-like [28,29]. The large EJ is undesirable regarding leakage current and reliability [30]. The trade-off between Schottky junction field EJ (at the middle of Schottky contact between p-grids) in off-state and the VF of the SiC JBS diode with Schottky contact to p-grid is shown in Figure 7. The figure indicates that increasing the WJFET cannot eliminate the dynamic dispersion of VF. Therefore, an Ohmic contact to p-grid is required in SiC JBS diode.

Conclusions
This work reveals the significance of the property of electrical contact to p-grid in power devices. The silicon carbide (SiC) junction barrier Schottky (JBS) diode, which is widely used in power circuits, is adopted in this paper as a case study. The property of the contact to p-grid (whether it is a Schottky Figure 7. The trade-off between Schottky junction field E J and the forward voltage V F in SiC JBS with a Schottky contact to p-grid.