Mobile-Phone Antenna Array with Diamond-Ring Slot Elements for 5G Massive MIMO Systems

: A design of mobile-phone antenna array with diamond-ring slot elements is proposed for ﬁfth generation (5G) massive multiple-input / multiple-output (MIMO) systems. The conﬁguration of the design consists of four double-fed diamond-ring slot antenna elements placed at di ﬀ erent corners of the mobile-phone printed circuit board (PCB). A low-cost FR-4 dielectric with an overall dimension of 75 × 150 mm 2 is used as the design substrate. The antenna elements are fed by 50-Ohm L-shaped microstrip-lines. Due to the orthogonal placement of microstrip feed lines, the diamond-ring slot elements can exhibit the polarization and radiation pattern diversity characteristic. A good impedance bandwidth (S 11 ≤ − 10 dB) of 3.2–4 GHz has been achieved for each antenna radiator. However, for S 11 ≤ − 6 dB, this value is 3–4.2 GHz. The proposed design provides the required radiation coverage of 5G smartphones. The performance of the proposed MIMO antenna design is examined using both simulation and experiment. High isolation, high e ﬃ ciency and su ﬃ cient gain-level characteristics have been obtained for the proposed MIMO smartphone antenna. In addition, the calculated total active reﬂection coe ﬃ cient (TARC) and envelope correlation coe ﬃ cient (ECC) of the antenna elements are very low over the whole band of interest which verify the capability of the proposed multi-antenna systems for massive MIMO and diversity applications. Furthermore, the properties of the design in Data-mode / Talk-mode are investigated and presented.


Introduction
Nowadays, there is an increased interest in research on MIMO systems in wireless communication [1,2].It has incomparable advantages in improving the wireless link transmission capacity and reliability.In MIMO systems, multiple antennas are deployed at both transmitter and receiver sides [3].This technology is a key component and probably the most established to truly reach the promised transfer data rates of fifth generation (5G) communication systems [4,5].MIMO antennas are important for increasing channel capacity and link reliability [6,7].Standard MIMO networks tend to use two or four antennas in a single physical package.However, massive MIMO is a MIMO system with an especially high number of antennas [8].A 2 × 2 MIMO system has been successfully applied for fourth generation (4G) mobile communications and it is expected that the massive MIMO system with a large number of MIMO antennas is very promising for 5G wireless communications [9].The greater number of elements in a network will make it more resistant to interference and intentional jamming [10].
Among the antennas which are used for MIMO applications, printed antennas are more appropriate due to their low cost, easy fabrication and their capability of easily being integrated to small terminal devices [11].However, placing multiple antennas in the limited space of a transceiver poses a significant challenge in the incorporation of the MIMO technique.According to the requirement of cellular communications, compact, wideband and high isolation MIMO antenna is an urgent demand in the future mobile terminal and the portable applications [12][13][14][15][16][17].Recently, several techniques have been introduced to design massive MIMO antennas for 4G and sub-6 GHz 5G mobile terminals [18][19][20][21][22][23][24][25][26][27].
We propose here a new design of Eight-port mobile-phone antenna with compact dual-polarized radiation elements providing wide impedance bandwidths for 5G applications.Eight-element MIMO smartphone antenna can achieve the channel capacity of 37 bps/Hz which is close to eight times that of a single antenna for single-input/single-output operation.With such a channel capacity and a wide frequency spectrum (200 MHz, at least), the data rate can be much higher than 1 Gbps.The antenna is designed to operate at 3.6 GHz, a candidate frequency band for sub-6-GHz 5G cellular networks, proposed by Ofcom, UK [28].The design configuration contains four elements of double-fed/dual-polarized slot-ring antennas placed at corners of the printed circuit board (PCB).The antenna elements exhibit wide impedance bandwidth with low mutual coupling function providing pattern and polarization diversity characteristics at different sides of the mobile-phone PCB.As a result, the design not only can provide full radiation coverage but also it can support different polarizations.The computer simulation technology (CST) software was used to investigate antenna characteristics [29].Fundamental properties of the single-element and its MIMO design in terms of S parameters, efficiency, radiation pattern, envelope correlation coefficient (ECC), total active reflection coefficient (TARC) are investigated.In addition, the performance of the designed mobile-phone antenna in Data-Mode/Talk-Mode are studied.

Single-Element Diamond-Ring Slot Antenna
Figure 1 depicts the configuration of the dual-polarized diamond-ring antenna.The antenna is designed on an FR-4 substrate (h = 1.6 mm, ε = 4.4, and δ = 0.025).
Its configuration contains a diamond-ring slot radiator with a pair of L-shaped microstrip feed lines.Parameter values of the designed antenna and its MIMO configuration are specified in Table 1.The motive behind the presented design is to achieve a dual-polarized wideband antenna with compact-size and capability of integration onto smartphone PCB.This has been achieved by using the diamond-ring slot antenna with L-shaped microstrip feed lines.The slot antenna is one type of printed antenna that has been investigated extensively for different wireless systems for several decades because of its attractive features including light-weight, compactness and ease of integration with radio frequency (RF) circuit [30].The ring-slot antenna can excite two orthogonal polarization if it is fed differently [31].This makes the printed-ring-slot antennas attractive.The resonant frequency of the antenna is mainly determined by the circumference length of the employed diamond-ring slot.Therefore, the circumference length of the diamond-ring slot needs to satisfy the dielectric wavelength at the corresponding frequency point, where W x /2 + g = λ.However, the length of feed-line (L f + L 1 ) also has a little effect on the frequency point and impedance-bandwidth of the design.efficiency, radiation pattern, envelope correlation coefficient (ECC), total active reflection coefficient (TARC) are investigated.In addition, the performance of the designed mobile-phone antenna in Data-Mode/Talk-Mode are studied.Configurations and S parameters of the square-ring slot with rectangular feed line, a diamond-ring slot with rectangular feed line, and the proposed diamond-ring slot radiator with L-shaped feed line are illustrated and compared in Figure 2a-c, respectively.It can be observed that by using the proposed design (Figure 2c), the antenna not only provides wider impedance bandwidth but it also exhibits high isolation with low mutual coupling characteristic (less than −20 dB) at the desired operation band.As shown, the operation frequency of the slot radiator with L-shaped feed lines spans from 3.2 to 4 GHz (800 MHz bandwidth).For S 11 ≤ −6 dB, this value is 3-4.2GHz.

Single-Element Diamond-Ring Slot Antenna
S 11 characteristics of varying design parameters including W x , L 1 , x and W 1 are illustrated in Figure 3. Figure 3a depicts the effects of diamond-ring size (W x ) on the resonance frequency: when its size decreases from 8 to 6 mm, the antenna resonance varies from 3.2 to 4.6 GHz.The frequency resonance of the antenna is also affected by the size of the L-shaped feed line arm (L 1 ).As shown in Figure 3b, the antenna operation frequency tunes to lower frequencies (without any changes on its bandwidth or isolation).Figure 3c illustrates the S 11 results for various values of x (width of the diamond-ring slot-line).As shown, it mainly affects the impedance bandwidth of the antenna: when its size changes from 0.5 to 2 mm, the antenna operation bandwidth varies from 0.3 to 1.2 GHz.Another important parameter of the dual-polarized diamond-ring slot antenna design is the length of the feed line arm (L 1 ) which tunes the isolation characteristic.As can be observed from the results shown in Figure 3d, the antenna reflection coefficient tunes from −18 to less than −40 dB.
Configurations and S parameters of the square-ring slot with rectangular feed line, a diamondring slot with rectangular feed line, and the proposed diamond-ring slot radiator with L-shaped feed line are illustrated and compared in Figure 2a-c, respectively.It can be observed that by using the proposed design (Figure 2c), the antenna not only provides wider impedance bandwidth but it also exhibi operat from S11 characteristics of varying design parameters including Wx, L1, x and W1 are illustrated in Figure 3. Figure 3a depicts the effects of diamond-ring size (Wx) on the resonance frequency: when its size decreases from 8 to 6 mm, the antenna resonance varies from 3.2 to 4.6 GHz.The frequency resonance of the antenna is also affected by the size of the L-shaped feed line arm (L1).As shown in Figure 3b, the antenna operation frequency tunes to lower frequencies (without any changes on its bandwidth or isolation).Figure 3c illustrates the S11 results for various values of x (width of the diamond-ring slot-line).As shown, it mainly affects the impedance bandwidth of the antenna: when its size changes from 0.5 to 2 mm, the antenna operation bandwidth varies from 0.3 to 1.2 GHz.Another important parameter of the dual-polarized diamond-ring slot antenna design is the length of the feed line arm (L1) which tunes the isolation characteristic.As can be observed from the results shown in Figure 3d, the antenna reflection coefficient tunes from −18 to less than −40 dB.S11 characteristics of varying design parameters including Wx, L1, x and W1 are illustrated in Figure 3. Figure 3a depicts the effects of diamond-ring size (Wx) on the resonance frequency: when its size decreases from 8 to 6 mm, the antenna resonance varies from 3.2 to 4.6 GHz.The frequency resonance of the antenna is also affected by the size of the L-shaped feed line arm (L1).As shown in Figure 3b, the antenna operation frequency tunes to lower frequencies (without any changes on its bandwidth or isolation).Figure 3c illustrates the S11 results for various values of x (width of the diamond-ring slot-line).As shown, it mainly affects the impedance bandwidth of the antenna: when its size changes from 0.5 to 2 mm, the antenna operation bandwidth varies from 0.3 to 1.2 GHz.Another important parameter of the dual-polarized diamond-ring slot antenna design is the length of the feed line arm (L1) which tunes the isolation characteristic.As can be observed from the results shown in Figure 3d, the antenna reflection coefficient tunes from −18 to less than −40 dB. Figure 4 shows the surface current distributions in the ground plane of the antenna at 3.6 GHz.As shown, the surface currents are mainly distributed around the diamond-ring slot radiator.In addition, for the different feeding ports of the antenna, the currents densities are equal and opposite due to the polarization diversity function [32][33][34].Figure 5 illustrates the 3D radiation patterns of the Figure 4 shows the surface current distributions in the ground plane of the antenna at 3.6 GHz.As shown, the surface currents are mainly distributed around the diamond-ring slot radiator.In addition, for the different feeding ports of the antenna, the currents densities are equal and opposite due to the polarization diversity function [32][33][34].Figure 5 illustrates the 3D radiation patterns of the antenna when it is fed differently (Port 1 and Port 2).As seen, the antenna exhibits similar radiation patterns with different orthogonal polarizations and more than 3 dB realized-gain.Radiation characteristics of the dual-polarized diamond-ring slot antenna in terms of radiation efficiency, total efficiency, and maximum gain are illustrated in Figure 6.As seen, the antenna provides high efficiencies.More than 80% radiation and total efficiency properties are obtained over the entire operation band (3.2-4 GHz).It can be observed that the antenna exhibits almost similar radiation and total efficiency.In addition, the antenna has around 2.5 dBi directivity.A prototype of the design was fabricated and its S parameters were tested.Figure 7 shows a photograph of the fabricated prototype in the measurement setup.A prototype of the design was fabricated and its S parameters were tested.Figure 7 shows a photograph of the fabricated prototype in the measurement setup.Figure 8 illustrates the measured and simulated S parameter results of the fabricated antenna.It is observed that the fabricated antenna works properly at the desired frequency range.

Mobile-Phone Antenna Design
The simulated design layout of the mobile-phone antenna design is shown in Figure 9.It was implemented on an FR4 substrate with an overall dimension of 75 × 150 mm 2 .Four elements of the dual-polarized diamond-ring slot radiators are employed at the corner of the mobile-phone PCB.As can be observed, due to the compact size of the employed radiator, there is enough spaces in the A prototype of the design was fabricated and its S parameters were tested.Figure 7 shows a photograph of the fabricated prototype in the measurement setup.Figure 8 illustrates the measured and simulated S parameter results of the fabricated antenna.It is observed that the fabricated antenna works properly at the desired frequency range.

Mobile-Phone Antenna Design
The simulated design layout of the mobile-phone antenna design is shown in Figure 9.It was implemented on an FR4 substrate with an overall dimension of 75 × 150 mm 2 .Four elements of the dual-polarized diamond-ring slot radiators are employed at the corner of the mobile-phone PCB.As can be observed, due to the compact size of the employed radiator, there is enough spaces in the configuration of smartphone antenna PCB to add other antennas covering different frequencies of

Mobile-Phone Antenna Design
The simulated design layout of the mobile-phone antenna design is shown in Figure 9.It was implemented on an FR4 substrate with an overall dimension of 75 × 150 mm 2 .Four elements of the dual-polarized diamond-ring slot radiators are employed at the corner of the mobile-phone PCB.As can be observed, due to the compact size of the employed radiator, there is enough spaces in the configuration of smartphone antenna PCB to add other antennas covering different frequencies of 3G/4G mobile terminals.Figure 10 illustrates the simulated S parameters (including S nn and S mn ) of the design over its operation band.It is evident that the proposed mobile-phone antenna exhibits good S parameters with wide bandwidth and low mutual coupling characteristics.As mentioned above, the dual-polarized radiation elements provide similar performances.3D radiation patterns of antennas 1 and 2 at 3.6 GHz is represented in Figure 11.As seen, the antenna elements have quasi-omnidirectional radiation patterns covering the top and bottom portions of the mobile-phone PCB.Top-views of the radiation patterns for the proposed mobile-phone antenna design are displayed in Figure 12.It can be seen that each side of the mobile-phone PCB has been covered with differently polarized radiation patterns.Thus, the MIMO antenna exhibited good radiation coverage and can support different polarizations which make it more suitable to be used in future smartphones.Furthermore, the antenna provides high radiation and total efficiencies over the operation band, as illustrated in Figure 13: more than 70% radiation and total efficiencies were obtained for the radiation elements at 3.6 GHz.Top-views of the radiation patterns for the proposed mobile-phone antenna design are displayed in Figure 12.It can be seen that each side of the mobile-phone PCB has been covered with differently polarized radiation patterns.Thus, the MIMO antenna exhibited good radiation coverage and can support different polarizations which make it more suitable to be used in future smartphones.Furthermore, the antenna provides high radiation and total efficiencies over the operation band, as illustrated in Figure 13: more than 70% radiation and total efficiencies were obtained for the radiation elements at 3.6 GHz.Top-views of the radiation patterns for the proposed mobile-phone antenna design are displayed in Figure 12.It can be seen that each side of the mobile-phone PCB has been covered with differently polarized radiation patterns.Thus, the MIMO antenna exhibited good radiation coverage and can support different polarizations which make it more suitable to be used in future smartphones.Furthermore, the antenna provides high radiation and total efficiencies over the operation band, as Electronics 2019, 8, 521 9 of 17 illustrated in Figure 13: more than 70% radiation and total efficiencies were obtained for the radiation elements at 3.6 GHz.
The proposed mobile-phone antenna was fabricated and its characteristics were tested in the Antenna Laboratory at the University of Bradford.Top and bottom views of the prototype are shown in Figure 14a,b, respectively.The mobile-phone antenna is constructed on a cheap FR4 dielectric with an overall dimension of 75 × 150 × 1.6 mm 3 .During the measurement process, 50-Ω RF loads are employed for the elements not under test to avoid their effects, as shown in Figure 14c.The measured and simulated S parameters (S nn : S 11 -S 88 and S mn : S 21 -S 81 ) of the fabricated design are illustrated in Figure 15.As illustrated, the diamond-ring slot resonators achieve good S parameters with sufficient impedance bandwidth and low mutual coupling characteristic in the desired frequency range.Some deviations from the measurements arise from the errors in fabrication, feeding and experiment processes.The proposed mobile-phone antenna was fabricated and its characteristics were tested in the Antenna Laboratory at the University of Bradford.Top and bottom views of the prototype are shown in Figure 14a,b, respectively.The mobile-phone antenna is constructed on a cheap FR4 dielectric with an overall dimension of 75 × 150 × 1.6 mm 3 .During the measurement process, 50-Ω RF loads are employed for the elements not under test to avoid their effects, as shown in Figure 14c.The measured and simulated S parameters (Snn: S11-S88 and Smn: S21-S81) of the fabricated design are illustrated in Figure 15.As illustrated, the diamond-ring slot resonators achieve good S parameters with sufficient impedance bandwidth and low mutual coupling characteristic in the desired frequency range.Some deviations from the measurements arise from the errors in fabrication, feeding and experiment processes.According to the point that the radiation elements with the same placements and polarizations provide similar radiation patterns, 2D polar radiation patterns of the adjacent resonators (including Ant. 1 and Ant. 2) were measured at center operating frequency (3.6 GHz) and illustrated in Figure 16.As shown, the sample prototype exhibits good radiation patterns and provides acceptable agreement with simulations.In addition, the antenna elements with different polarizations provide sufficient gain values at the center frequency of the operation band.According to the point that the radiation elements with the same placements and polarizations provide similar radiation patterns, 2D polar radiation patterns of the adjacent resonators (including Ant. 1 and Ant. 2) were measured at center operating frequency (3.6 GHz) and illustrated in Figure 16.As shown, the sample prototype exhibits good radiation patterns and provides acceptable agreement with simulations.In addition, the antenna elements with different polarizations provide sufficient gain values at the center frequency of the operation band.In order to ensure that the MIMO antenna can work properly, ECC and TARC characteristics are two important parameters which should be considered in MIMO antennas [35,36].The ECC and TARC of two elements can be calculated from the S parameters using the formula described as: Figure 17 shows the calculated ECC and TARC results from simulated and measured S parameters of the mobile-phone antenna design.As evident from figures, the calculated ECC and TARC results are very low over the whole band of interest.The design provides less than 0.01 ECC over the entire operating band and proves that two adjacent antenna elements are irrelevant.In addition, its TARC value is less than −30 at 3.6 GHz.Table 2 summarizes and compares the fundamental characteristics of the presented mobile-phone antenna with the recently reported 5G mobile-phone antenna designs [16][17][18][19][20][21][22][23][24][25].It can be observed that the proposed design can provide better performances in terms of efficiency, isolation and ECC.In addition, it exhibits wider bandwidth with pattern and polarization diversity characteristics to cover different sides of the mobile-phone PCB.
Electronics 2019, 7, x FOR PEER REVIEW 12 of 17 In order to ensure that the MIMO antenna can work properly, ECC and TARC characteristics are two important parameters which should be considered in MIMO antennas [35,36].The ECC and TARC of two elements can be calculated from the S parameters using the formula described as: Figure 17 shows the calculated ECC and TARC results from simulated and measured S parameters of the mobile-phone antenna design.As evident from figures, the calculated ECC and TARC results are very low over the whole band of interest.The design provides less than 0.01 ECC over the entire operating band and proves that two adjacent antenna elements are irrelevant.In addition, its TARC value is less than −30 at 3.6 GHz.Table 2 summarizes and compares the fundamental characteristics of the presented mobile-phone antenna with the recently reported 5G mobile-phone antenna designs [16][17][18][19][20][21][22][23][24][25].It can be observed that the proposed design can provide better performances in terms of efficiency, isolation and ECC.In addition, it exhibits wider bandwidth with pattern and polarization diversity characteristics to cover different sides of the mobile-phone PCB.The impact of human-hand/human-head on the characteristics of the design in terms of total efficiency and antenna realized-gain were investigated in this section [37][38][39].As illustrated in Figure 18, different scenarios including right-hand and left-hand modes for top-layer and back-layer of the design are studied in simulations.According to the obtained results, the mobile-phone antenna design and its radiators exhibit good performances and provide sufficient total efficiencies in the presence of the human hand.Due to the symmetric configuration of the proposed design, it performs almost similarly for different hand scenarios.The maximum reductions of the radiation properties are observed for the radiation elements partially covered by the user hand which is due to the nature of hand tissue properties which can highly absorb the radiation power.As can be observed, the antenna elements provide 25-55% total efficiencies over the operation band of 3.2-4 GHz.The impact of human-hand/human-head on the characteristics of the design in terms of total efficiency and antenna realized-gain were investigated in this section [37][38][39].As illustrated in Figure 18, different scenarios including right-hand and left-hand modes for top-layer and back-layer of the design are studied in simulations.According to the obtained results, the mobile-phone antenna design and its radiators exhibit good performances and provide sufficient total efficiencies in the presence of the human hand.Due to the symmetric configuration of the proposed design, it performs almost similarly for different hand scenarios.The maximum reductions of the radiation properties are observed for the radiation elements partially covered by the user hand which is due to the nature of hand tissue properties which can highly absorb the radiation power.As can be observed, the antenna elements provide 25-55% total efficiencies over the operation band of 3.2-4 GHz.3D radiation patterns of the mobile-phone antenna in Talk-Mode at 3.6 GHz are illustrated in Figure 19a.It should be noted that the radiation performance of each antenna element mainly depends on its locations in the Talk-Mode scenario.As shown, the realized gain characteristic of the design varies from 3.2 to 4.9 dB.Compared with the radiation patterns in free space (Figure 12), due to the existence of the user's head and hand, radiation patterns are a bit distorted and become weaker.One can see that antenna elements are touched by different parts of the hand and head phantoms in the presented Talk-Mode.3D radiation patterns of the mobile-phone antenna in Talk-Mode at 3.6 GHz are illustrated in Figure 19a.It should be noted that the radiation performance of each antenna element mainly depends on its locations in the Talk-Mode scenario.As shown, the realized gain characteristic of the design varies from 3.2 to 4.9 dB.Compared with the radiation patterns in free space (Figure 12), due to the existence of the user's head and hand, radiation patterns are a bit distorted and become weaker.One can see that antenna elements are touched by different parts of the hand and head phantoms in the presented Talk-Mode.The maximum reductions of the radiation properties are observed for the elements that are located near to user-head (Ant.3 and Ant.4) [40].However, the difference is not very significant.The 2D-polar (linear-scaling) radiation patterns of the design are illustrated in Figure 19b.As can be observed, the directivity of the antenna radiation pattern is maximum in the opposite direction of the head, which is most important part of the body to protect from the radiation.The main lobe of each single-element directs most of the power while the other lobes should be negligible.The maximum reductions of the radiation properties are observed for the elements that are located near to user-head (Ant.3 and Ant.4) [40].However, the difference is not very significant.The 2D-polar (linear-scaling) radiation patterns of the design are illustrated in Figure 19b.As can be observed, the directivity of the antenna radiation pattern is maximum in the opposite direction of the head, which is most important part of the body to protect from the radiation.The main lobe of each single-element directs most of the power while the other lobes should be negligible.
Figure 20 depicts the total efficiencies and reflection coefficient (S nn ) of the antenna elements in the presence of the user-head and user-hand in Talk-Mode scenario.As seen, the diversion of the S nn characteristic of the design is not significant.In addition, the proposed MIMO design exhibit sufficient efficiency in its operation bandwidth.Based on the above analysis, we can conclude the MIMO design provides sufficient efficiency, radiation coverage and gain levels for diamond-ring slot radiators.
Electronics 2019, 7, x FOR PEER REVIEW 15 of 17 Figure 20 depicts the total efficiencies and reflection coefficient (Snn) of the antenna elements in the presence of the user-head and user-hand in Talk-Mode scenario.As seen, the diversion of the Snn characteristic of the design is not significant.In addition, the proposed MIMO design exhibit sufficient efficiency in its operation bandwidth.Based on the above analysis, we can conclude the MIMO design provides sufficient efficiency, radiation coverage and gain levels for diamond-ring slot radiators.

Figure 2 .
Figure 2. Various structures and S parameter results of: (a) square-ring slot with rectangular feed line, (b) diamond-ring slot with rectangular feed line, and (c) the proposed diamond-ring slot radiator with L-shaped feed line.

Figure 2 .Figure 2 .
Figure 2. Various structures and S parameter results of: (a) square-ring slot with rectangular feed line, (b) diamond-ring slot with rectangular feed line, and (c) the proposed diamond-ring slot radiator with L-shaped feed line.

Figure 3 .
Figure 3. S 11 results of the diamond-ring antenna for various values of (a) W x , (b) L 1 , (c) x, and (d) W 1 .

Figure 5 .
Figure 5. 3D views of the dual-polarized radiation patterns from (a) feeding port 1 and (b) feeding port 2.
Figure 8 illustrates the measured and simulated S parameter results of the fabricated antenna.It is observed that the fabricated antenna works properly at the desired frequency range.

Figure 5 .
Figure 5. 3D views of the dual-polarized radiation patterns from (a) feeding port 1 and (b) feeding port 2.

Figure 6 .
Figure 6.Radiation, total efficiencies, maximum gain of the diamond-ring slot antenna.Figure 6. Radiation, total efficiencies, maximum gain of the diamond-ring slot antenna.

Figure 6 .
Figure 6.Radiation, total efficiencies, maximum gain of the diamond-ring slot antenna.Figure 6. Radiation, total efficiencies, maximum gain of the diamond-ring slot antenna.

Figure 7 .
Figure 7. Photograph of the fabricated prototype in the measurement setup.

Figure 8 .
Figure 8. Measured and simulated S parameter results of the fabricated antenna.

Figure 7 .
Figure 7. Photograph of the fabricated prototype in the measurement setup.

Figure 7 .
Figure 7. Photograph of the fabricated prototype in the measurement setup.

Figure 8 .
Figure 8. Measured and simulated S parameter results of the fabricated antenna.

Figure 8 .
Figure 8. Measured and simulated S parameter results of the fabricated antenna.

Figure 10 .Figure 10 .Figure 11 .
Figure 10.(a) S nn and (b) S mn results of the mobile-phone antenna.

Figure 11 .
Figure 11.3D transparent views of the radiation patterns for (a) feeding port 1 and (b) feeding port 2.

Figure 14 .
Figure 14.(a) Top, (b) bottom views of the fabricated design and (c) the prototype connected to the cables and 50-Ohm loads.

Figure 14 .Figure 15 .Figure 16 .
Figure 14.(a) Top, (b) bottom views of the fabricated design and (c) the prototype connected to the cables and 50-Ohm loads.

Figure 18 .
Figure 18.Placement and total efficiencies of the design for different user-hand scenarios (a) righthand/top-layer, (b) right-hand/back-layer, (c) left-hand/top-layer and (d) left-hand/back-layer.

Figure 18 .
Figure 18.Placement and total efficiencies of the design for different user-hand scenarios (a) right-hand/top-layer, (b) right-hand/back-layer, (c) left-hand/top-layer and (d) left-hand/back-layer.

Figure 19 .
Figure 19.(a) 3D and (b) 2D linearly-scaled radiation patterns of the mobile-phone antenna in Talk-Mode scenario.

Figure 19 .
Figure 19.(a) 3D and (b) 2D linearly-scaled radiation patterns of the mobile-phone antenna in Talk-Mode scenario.

Figure 20 .
Figure 20.(a) Snn and (b) total efficiencies of the proposed smartphone antenna in Talk-Mode scenario.

Table 1 .
Parameter values of the single-element antenna and its MIMO array design.

Table 2 .
Comparison between the presented and recently reported 5G mobile-phone antennas.

Table 2 .
Comparison between the presented and recently reported 5G mobile-phone antennas.