A Nonisolated Three-Port DC–DC Converter with Continuous Input and Output Currents Based on Cuk Topology for PV/Fuel Cell Applications

: A nonisolated three-port DC–DC converter based on Cuk topology (NI-TPC) to handle the renewable sources (RS) is proposed in this paper. This converter includes two unidirectional input ports accommodating both a fuel cell (FC) and photovoltaic (PV) cell; and one output port with DC load. Due to the inductors at all the ports, it claims the advantage of continuous input and output currents. Additionally, it uses less number of switches, diodes and inductors compared with conventional ‘n-1’ separate Cuk converters. Synthesis procedure for a generalized n-port DC–DC structure is explained. The derivation law based on conventional Cuk converter, operating principle, design calculation, and analysis are presented in detail, and then the analysis is validated through simulation and a 100W prototype, verifying the performance of the proposed NI-TPC converter.


Introduction
Fast and society-threatening global warming and health hazards due to the combustion of fossil fuels have triggered the research and development of more efficient and cleaner renewable sources (RS) namely solar, wind, fuel cell etc.Many DC-DC converters with a single inductor, for example, buck and boost converters and two inductor converters, such as Sepic, Cuk, and zeta converters, have been used to connect RS and load [1,2].However, the stochastic and time-varying characteristics of these sources and unpredictable demand at load side necessitate the backup source for continuous power flow to the load.This condition forces the system to have at least two input ports; one for RS and another for a backup source such as fuel cell/wind/battery.
In the recent past, new converter topologies called multiport converters (MPC) have been proposed to integrate these RS, which ensure the continuous power flow to the load.The structure of conventional and MPC system is shown in Figure 1.The MPCs enhance the utilization of power sources based on their V-I characteristics, availability and cost [3].Multiport converters (MPC) which claim the advantage of component sharing are acknowledged as one of the promising topologies to integrate the RS to cater the future energy generation requirements.Moreover, compact structure and lesser conversion stages are the reasons to adopt MPC for numerous applications such as hybrid power system [4], renewable energy integration [5], hybrid vehicles [6], aerospace applications, and uninterrupted power supplies.This MPC, in particular, the three-port converter (TPC) can be divided into three groups: (1) the isolated DC-DC converter; (2) semi-isolated DC-DC converter; and (3) nonisolated converter topologies.The isolated TPC uses a transformer with a high-frequency to provide magnetic coupling and electrical isolation between the source and load [6][7][8]; partially isolated converters use a common DC bus along with magnetic coupling [9].A nonisolated TPC uses common DC bus and finds applications where the isolation is not needed between the ports [10][11][12].
Electronics 2019, 8, x FOR PEER REVIEW 2 of 20 nonisolated converter topologies.The isolated TPC uses a transformer with a high-frequency to provide magnetic coupling and electrical isolation between the source and load [6][7][8]; partially isolated converters use a common DC bus along with magnetic coupling [9].A nonisolated TPC uses common DC bus and finds applications where the isolation is not needed between the ports [10][11][12].TPCs can be configured in two topologies based on the nature of the input sources: series and parallel.In the series topology, the output voltage regulation becomes challenging if one of the input sources reduces (e.g., in PV shading condition) [13].Assumptions and conditions to design the converters with multiple input-single output (MISO) from the conventional single input-single output (SISO) structures are explained [14].The systematic way of synthesizing MISO converters is detailed in Reference [15].Topology generation methods and principles for developing a family of NI-TPC are proposed [16].These TPCs are developed by introducing a SISO model in an existing dual input or two output converters.In Reference [17], an approach to systematically derive MPCs with DC link inductor concept and with two input and two output converters is proposed.This procedure has developed numerous TPC topologies.A novel nonisolated TPC with single inductor is proposed for RS [18].This converter features the integration and control of bidirectional load, compactness, single stage power conversion between any two ports, and seven possible operational modes.The design of a NI-TPC using one switch for a standalone PV power system integrating energy storage is proposed in Reference [19].A synchronous switch with a pair of diodes has been utilized instead of two individual switches.However, the converters in both the stages must operate synchronously.The inherent buck-boost characteristics of the Cuk converter provide flexibility for standalone and grid-tied applications when the output voltage required is more or less than the input voltage.Continuous current at the input and output ports and the identical switching voltage waveforms appearing across the inductors are the salient features of the Cuk converter [20].New topologies with high voltage ratio have been proposed using Cuk converter in Reference [21] for renewable power applications.In Reference [9], A TPC is presented by integrating a Cuk converter with bidirectional power flow and a full-bridge (FB) rectifier circuit for renewable energy applications.It used a transformer with high frequency.This converter consists of two nonisolated and one isolated ports.A nonisolated DC-DC TPC using integrated boost-cuk topology with high voltage gain is proposed [22].An isolated TPC depending on Cuk converter is presented in Reference [23] by incorporating the inductor and transformers on a single core.Three winding transformer used in the above converter increases the size.Moreover, it uses more number of switches.The three-port Cuk converter to solve the zero-ripple problem is presented by designing a single integrated magnetic core having all the magnetics on it [24].Methods based on circuit theory and the structure of the core are used to analyze the ripples.However, these converters are the isolated type and use bulky transformers and inductors.In Reference [25], a DC-DC converter combining a SEPIC and Cuk TPCs can be configured in two topologies based on the nature of the input sources: series and parallel.In the series topology, the output voltage regulation becomes challenging if one of the input sources reduces (e.g., in PV shading condition) [13].Assumptions and conditions to design the converters with multiple input-single output (MISO) from the conventional single input-single output (SISO) structures are explained [14].The systematic way of synthesizing MISO converters is detailed in Reference [15].Topology generation methods and principles for developing a family of NI-TPC are proposed [16].These TPCs are developed by introducing a SISO model in an existing dual input or two output converters.In Reference [17], an approach to systematically derive MPCs with DC link inductor concept and with two input and two output converters is proposed.This procedure has developed numerous TPC topologies.A novel nonisolated TPC with single inductor is proposed for RS [18].This converter features the integration and control of bidirectional load, compactness, single stage power conversion between any two ports, and seven possible operational modes.The design of a NI-TPC using one switch for a standalone PV power system integrating energy storage is proposed in Reference [19].A synchronous switch with a pair of diodes has been utilized instead of two individual switches.However, the converters in both the stages must operate synchronously.The inherent buck-boost characteristics of the Cuk converter provide flexibility for standalone and grid-tied applications when the output voltage required is more or less than the input voltage.Continuous current at the input and output ports and the identical switching voltage waveforms appearing across the inductors are the salient features of the Cuk converter [20].New topologies with high voltage ratio have been proposed using Cuk converter in Reference [21] for renewable power applications.In Reference [9], A TPC is presented by integrating a Cuk converter with bidirectional power flow and a full-bridge (FB) rectifier circuit for renewable energy applications.It used a transformer with high frequency.This converter consists of two nonisolated and one isolated ports.A nonisolated DC-DC TPC using integrated boost-cuk topology with high voltage gain is proposed [22].An isolated TPC depending on Cuk converter is presented in Reference [23] by incorporating the inductor and transformers on a single core.Three winding transformer used in the above converter increases the size.Moreover, it uses more number of switches.The three-port Cuk converter to solve the zero-ripple problem is presented by designing a single integrated magnetic core having all the magnetics on it [24].Methods based on circuit theory and the structure of the core are used to analyze the ripples.However, these converters are the isolated type and use bulky transformers and inductors.In Reference [25], a DC-DC converter combining a SEPIC and Cuk converter is proposed for bipolar DC microgrid applications.A single switch shared by both converters is an added advantage.However, the number of power components is greater.
However, the TPCs mentioned above fail to provide a high voltage conversion ratio and continuous current at all the ports.
The outstanding features of the proposed converter are

•
Both the input ports share common output inductor, hence minimizing the component count.

•
Continuous current with less ripple in all the ports (the input and output ports).

•
Delivered power from each input can be independently controlled • Buck-boost output voltages can be obtained.
To the best of the author's knowledge, the design and development of NI-TPC converter has not been reported earlier in literature.In this paper, the design, development, and extensive analysis of the proposed converter have been carried out to validate the performance of the converter.
Generally, the energy flow control modes and circuit analysis procedure are common sense and well discussed in many other papers [4,[26][27][28][29][30][31].However, the DC-DC structure of the Cuk-Cuk converter used for the system that integrates the input ports (1 and 2) to DC Bus (Port 3) is new, which increases the novelty of the paper.

Synthesis of the NI-TPC Converter
This section presents the illustration of synthesizing the proposed NI-TPC converter from a classical Cuk converter.Based on the fundamentals, the structure of the classical Cuk converter can be deduced to the input section, output section, and an energy buffer section that connects both, as shown in Figure 2. The capacitor acts as a voltage buffer and transfers energy from input to output section without consuming any energy.The input with voltage buffer and output sections are separated and connected as represented in Figure 2 to form the generalized n-port structure.
Electronics 2019, 8, x FOR PEER REVIEW 3 of 20 converter is proposed for bipolar DC microgrid applications.A single switch shared by both converters is an added advantage.However, the number of power components is greater.However, the TPCs mentioned above fail to provide a high voltage conversion ratio and continuous current at all the ports.
The outstanding features of the proposed converter are • Both the input ports share common output inductor, hence minimizing the component count.• Continuous current with less ripple in all the ports (the input and output ports).
• Delivered power from each input can be independently controlled • Buck-boost output voltages can be obtained.To the best of the author's knowledge, the design and development of NI-TPC converter has not been reported earlier in literature.In this paper, the design, development, and extensive analysis of the proposed converter have been carried out to validate the performance of the converter.
Generally, the energy flow control modes and circuit analysis procedure are common sense and well discussed in many other papers [4,[26][27][28][29][30][31].However, the DC-DC structure of the Cuk-Cuk converter used for the system that integrates the input ports (1 and 2) to DC Bus (Port 3) is new, which increases the novelty of the paper.

Synthesis of the NI-TPC Converter
This section presents the illustration of synthesizing the proposed NI-TPC converter from a classical Cuk converter.Based on the fundamentals, the structure of the classical Cuk converter can be deduced to the input section, output section, and an energy buffer section that connects both, as shown in Figure 2. The capacitor acts as a voltage buffer and transfers energy from input to output section without consuming any energy.The input with voltage buffer and output sections are separated and connected as represented in Figure 2 to form the generalized n-port structure.The resulting structure of the proposed 'n' port converter consists of 'n-1' input sources, 'n' inductors, 'n' capacitors, 'n-1' switches and a single diode is presented in Figure 3. Table 1 gives a comparison of the circuit elements used in the proposed and conventional structures.The resulting structure of the proposed 'n' port converter consists of 'n-1' input sources, 'n' inductors, 'n' capacitors, 'n-1' switches and a single diode is presented in Figure 3. Table 1 gives a comparison of the circuit elements used in the proposed and conventional structures.
A three-port converter with two input ports and a load port is taken for better understanding as shown in Figure 4.One can understand that it is based on the integration of two classical Cuk converters.The proposed TPC consists of three inductors (L 1 , L 2 , and L 0 ), three capacitors (C 1 , C 2 , and C 0 ), two switches (S 1 -S 2 ), and one diode (D 0 ).Power sources V 1 and V 2 are connected to the unidirectional input ports.

Circuit Elements Proposed n-Port Cuk-Cuk Converter (n-1) Individual Cuk Converters
Inductors n 2(n-1) A three-port converter with two input ports and a load port is taken for better understanding as shown in Figure 4.One can understand that it is based on the integration of two classical Cuk converters.The proposed TPC consists of three inductors (L1, L2, and L0), three capacitors (C1, C2, and C0), two switches (S1-S2), and one diode (D0).Power sources V1 and V2 are connected to the unidirectional input ports.

Operating Principles
Based on the availability of power sources, the proposed TPC can function in two different modes: the SISO and dual input single output (DISO) modes.Either of the input ports can cater to load in the absence of the other in SISO mode.In DISO mode, both sources contribute power to load when the primary power source is insufficient to meet the load demand.The proposed NI-TPC converter can function in all these modes through appropriate control.

SISO Mode
Figure 5a shows the Equivalent circuit when operating in SISO mode.The equivalent circuits of state 1 and state 2 are shown in Figure 5b,5c, respectively.The waveforms are not shown since it is similar to the classical Cuk converter.

State 1:
In this mode, switch S1 is ON, but the diode is not conducting.Voltage source V1 magnetizes the inductor L1.The positive voltage on the inductor makes the inductor current iL1 to increase linearly.The capacitor C1 is assumed precharged and discharging its energy to the load through the inductor L0.Hence, the inductor current iL2 increases linearly.In addition, it charges the output capacitor C0.Various currents and voltages can be expressed by (1).
A three-port converter with two input ports and a load port is taken for better understanding as shown in Figure 4.One can understand that it is based on the integration of two classical Cuk converters.The proposed TPC consists of three inductors (L1, L2, and L0), three capacitors (C1, C2, and C0), two switches (S1-S2), and one diode (D0).Power sources V1 and V2 are connected to the unidirectional input ports.

Operating Principles
Based on the availability of power sources, the proposed TPC can function in two different modes: the SISO and dual input single output (DISO) modes.Either of the input ports can cater to load in the absence of the other in SISO mode.In DISO mode, both sources contribute power to load when the primary power source is insufficient to meet the load demand.The proposed NI-TPC converter can function in all these modes through appropriate control.

SISO Mode
Figure 5a shows the Equivalent circuit when operating in SISO mode.The equivalent circuits of state 1 and state 2 are shown in Figure 5b,5c, respectively.The waveforms are not shown since it is similar to the classical Cuk converter.

State 1:
In this mode, switch S1 is ON, but the diode is not conducting.Voltage source V1 magnetizes the inductor L1.The positive voltage on the inductor makes the inductor current iL1 to increase linearly.The capacitor C1 is assumed precharged and discharging its energy to the load through the inductor L0.Hence, the inductor current iL2 increases linearly.In addition, it charges the output capacitor C0.Various currents and voltages can be expressed by (1).

Operating Principles
Based on the availability of power sources, the proposed TPC can function in two different modes: the SISO and dual input single output (DISO) modes.Either of the input ports can cater to load in the absence of the other in SISO mode.In DISO mode, both sources contribute power to load when the primary power source is insufficient to meet the load demand.The proposed NI-TPC converter can function in all these modes through appropriate control.

SISO Mode
Figure 5a shows the Equivalent circuit when operating in SISO mode.The equivalent circuits of state 1 and state 2 are shown in Figure 5b,c, respectively.The waveforms are not shown since it is similar to the classical Cuk converter.

State 1
In this mode, switch S 1 is ON, but the diode is not conducting.Voltage source V 1 magnetizes the inductor L 1 .The positive voltage on the inductor makes the inductor current i L1 to increase linearly.The capacitor C 1 is assumed precharged and discharging its energy to the load through the inductor L 0 .Hence, the inductor current i L2 increases linearly.In addition, it charges the output capacitor C 0 .Various currents and voltages can be expressed by (1).
In this state, switch S 1 is OFF while the diode conducts and freewheels.The voltage source V 1 together with the energy stored in the inductor L 1 , charge the capacitor C 1 through diode D 0 .The current in the inductor i L1 decreases linearly.The output inductor L 0 is demagnetized and its energy flows to the load through diode D 0 .Equation ( 2) is valid in this mode: Electronics 2019, 8, x FOR PEER REVIEW 5 of 20 State 2 In this state, switch S1 is OFF while the diode conducts and freewheels.The voltage source V1 together with the energy stored in the inductor L1, charge the capacitor C1 through diode D0.The current in the inductor iL1 decreases linearly.The output inductor L0 is demagnetized and its energy flows to the load through diode D0.Equation ( 2) is valid in this mode:

DISO Mode
Better utilization of power sources needs a suitable control technique to achieve the regulated output power.The appropriate switching pattern in various modes depends on the time multiplexing of switching signals.

DISO Mode
Better utilization of power sources needs a suitable control technique to achieve the regulated output power.The appropriate switching pattern in various modes depends on the time multiplexing of switching signals.
Selection of switching sequence can be done in many ways based on whether power is catered individually or simultaneously.A left-aligned switching pattern as shown in Figure 6 has been chosen in this work for analysis of the proposed converter.
Selection of switching sequence can be done in many ways based on whether power is catered individually or simultaneously.A left-aligned switching pattern as shown in Figure 6 has been chosen in this work for analysis of the proposed converter.

State 1
During this state, both switches S1 and S2 are ON, but the diode remains nonconducting.The voltage sources V1and V2 magnetize the inductors L1 and L2 respectively.The positive voltage on the inductors makes the inductor currents increase linearly.Capacitors C1 and C2 are assumed precharged and to be discharging energy.The load is catered by the capacitors discharge through the inductor L0.The corresponding equivalent circuit is illustrated in Figure 7a.The corresponding equations have been presented in (4).
In this interval, switch S1 is OFF and switch S2 is ON, but the diode stays nonconducting due to the voltage across capacitor C2.The voltage source V1 together with the energy stored in the inductor L1, charges the capacitor C1.V2 continues to discharge and magnetize the inductor L2.Due to the positive and constant voltage on inductor L2, its current raises linearly.The capacitor C2 continues to discharge as in Mode 1, and the load is catered by it through the inductor L0.The corresponding equivalent circuit is presented in Figure 7b.Equation ( 5) is derived for this mode.State 1 During this state, both switches S 1 and S 2 are ON, but the diode remains nonconducting.The voltage sources V 1 and V 2 magnetize the inductors L 1 and L 2 respectively.The positive voltage on the inductors makes the inductor currents increase linearly.Capacitors C 1 and C 2 are assumed precharged and to be discharging energy.The load is catered by the capacitors discharge through the inductor L 0 .The corresponding equivalent circuit is illustrated in Figure 7a.The corresponding equations have been presented in (4).During this state, both switches S1 and S2 are ON, but the diode remains nonconducting.The voltage sources V1and V2 magnetize the inductors L1 and L2 respectively.The positive voltage on the inductors makes the inductor currents increase linearly.Capacitors C1 and C2 are assumed precharged and to be discharging energy.The load is catered by the capacitors discharge through the inductor L0.The corresponding equivalent circuit is illustrated in Figure 7a.The corresponding equations have been presented in (4).
In this interval, switch S1 is OFF and switch S2 is ON, but the diode stays nonconducting due to the voltage across capacitor C2.The voltage source V1 together with the energy stored in the inductor L1, charges the capacitor C1.V2 continues to discharge and magnetize the inductor L2.Due to the positive and constant voltage on inductor L2, its current raises linearly.The capacitor C2 continues to discharge as in Mode 1, and the load is catered by it through the inductor L0.The corresponding equivalent circuit is presented in Figure 7b.Equation ( 5) is derived for this mode.

State 3
In this state, both switches S1 and S2 are OFF while the diode conducts and freewheels.The voltage sources V1 and V2 together with the energy stored in the inductors L1 and L2, charge capacitors C1 and C2 respectively.The current in the inductors iL1 and iL2 decreases linearly.The output inductor L0 discharges and the load is catered by it through the Diode D0.The equivalent circuit of this state is illustrated in Figure 7c.Various currents and voltages can be expressed as in (6).
Ideal operating conditions with Steady state and continuous conduction mode (CCM) is assumed to derive the expressions of the output voltage and voltage gain.

State 2
In this interval, switch S 1 is OFF and switch S 2 is ON, but the diode stays nonconducting due to the voltage across capacitor C 2 .The voltage source V 1 together with the energy stored in the inductor L 1 , charges the capacitor C 1 .V 2 continues to discharge and magnetize the inductor L 2 .Due to the positive and constant voltage on inductor L 2 , its current raises linearly.The capacitor C 2 continues to discharge as in Mode 1, and the load is catered by it through the inductor L 0 .The corresponding equivalent circuit is presented in Figure 7b.Equation ( 5) is derived for this mode.
In this state, both switches S 1 and S 2 are OFF while the diode conducts and freewheels.The voltage sources V 1 and V 2 together with the energy stored in the inductors L 1 and L 2 , charge capacitors C 1 and C 2 respectively.The current in the inductors i L1 and i L2 decreases linearly.The output inductor L 0 discharges and the load is catered by it through the Diode D 0 .The equivalent circuit of this state is illustrated in Figure 7c.Various currents and voltages can be expressed as in (6).
Ideal operating conditions with Steady state and continuous conduction mode (CCM) is assumed to derive the expressions of the output voltage and voltage gain.

Modeling and Analysis of the Converter
The derivation of various parameters and modeling of the proposed NI-TPC converter are presented in this section.

Voltage Gain
The analytical expression for the output voltage has been obtained by applying volt second balance theory on inductors.
The expression of the output voltage can be derived from Equations ( 7)-( 9).The voltage equation in terms of duty cycles is From (10), one can understand that the proposed converter operating in DISO mode has the same voltage gain compared with classical Cuk converter, which is plotted in Figure 8. Considering V 1 = V 2 = V, the output voltage of the proposed converter is presented in (11).Selecting the same duty ratio for both the switches leads to the output voltage equal to the one in classical Cuk converter as derived in (12).The voltage gain for an n-port DC-DC Cuk-Cuk converter with the proposed topology can be derived as in (13). Taking For an n-port converter, )( ) Taking δ1= δ2= δ For an n-port converter,  Applying the charge-sec balance principle on capacitors, the following equations are obtained.

Current Ripples of Inductors
Current ripples and inductor volt-second balance (IVSB) principle are used to design inductors.The inductor current ripple equations are modified to obtain equations for inductor values ( 16)- (18).Applying the charge-sec balance principle on capacitors, the following equations are obtained.

Current Ripples of Inductors
Current ripples and inductor volt-second balance (IVSB) principle are used to design inductors.The inductor current ripple equations are modified to obtain equations for inductor values ( 16)- (18). ) The values of the inductors can be found, if output voltage, source voltages, desired ripples, switching frequency and duty cycle are known.

Voltage Ripples of Capacitors
Voltage ripples and the capacitor charge-second balance (CCSB) principle are used to design capacitors.The voltage ripple equations are modified to obtain equations for capacitor values ( 19)- (21).
Output capacitor can be determined from the output voltage ripple.
The values of the capacitors can be found if the output voltage, source voltages, desired ripples, switching frequency and duty cycle are known.A 5% current ripples in inductors, 5% voltage ripples in buffer capacitor C 1 and 4% voltage ripples in output capacitor C 0 have been considered to design the parameters listed in Table 2.The converter is simulated and various current and voltage waveforms are presented in Figure 9a-j.

Small-Signal Modeling
Voltage regulation should be maintained in spite of the changes in input and output parameters in any power converter, which necessitates a design of feedback controller.Modeling plays a good role in providing information about the dynamic behavior of the converter and in deriving a feedback control system.Numerous modeling methods have been proposed for power electronic converters.The State-Space Averaging (SSA) method is the most commonly used method to design control loops and to investigate the transient and steady state response of the converter.This modeling method has

Small-Signal Modeling
Voltage regulation should be maintained in spite of the changes in input and output parameters in any power converter, which necessitates a design of feedback controller.Modeling plays a good role in providing information about the dynamic behavior of the converter and in deriving a feedback control system.Numerous modeling methods have been proposed for power electronic converters.The State-Space Averaging (SSA) method is the most commonly used method to design control loops and to investigate the transient and steady state response of the converter.This modeling method has three steps: (1) writing the state-space equations for all states in a switching cycle; (2) derivation of average state-space equation; and (3) applying perturbations to the averaged equation to derive the linear first order small-signal equations, from which different transfer functions relating the inputs and outputs can be obtained.Then, matrices A and B are formed, which describe the converter model.The derived model fits in the following form (22). .
where X, U, Y and .
x = dx/dt represent the state vector, the input or control vector, the output vector and the derivative of X respectively.Matrices A, B, C and D are the system, control, output and feed-forward matrices respectively.A and B are used to extract various transfer functions of the system.
From the Equation (4) in Section 2 and according to circuit theory, the dynamic equations representing state-1 can be written as follows The derived dynamic equations representing state-2 and state-3 are given in ( 27) and ( 28) respectively.
The obtained state space model in matrix form is given in (29).
Using ( 29) with the obtained model, the transfer functions are derived and shown in ( 30)-(32).These transfer functions are evaluated using MATLAB commands to eliminate manual mistakes, and the step data analysis is obtained.Figure 10 illustrates the response of the plant to a unit step input.Using ( 29) with the obtained model, the transfer functions are derived and shown in ( 30)-(32).
[ ] These transfer functions are evaluated using MATLAB commands to eliminate manual mistakes, and the step data analysis is obtained.Figure 10  Figure 10a, 10b depicts the step response of the converter with step change in input sources V1 and V2 respectively.It is clear that the response is inverted as the Cuk converter has an inverted output.The steady state value settles at −0.6674 in Figure 10a and has an error of 33.26% with a peak overshoot of 62.7284%.In Figure 10b, the response settles at −0.9993 and has an error of 0.7% with a peak overshoot of 62.64644%.

Design of Controller
The most popular proportional plus integral (PI) controller has been designed to eliminate the steady state error pointed in Figure .10.One can obtain the proportional and the integral output as given in (30).Ziegler-Nichols PI tuning was adopted to obtain the values of the proportional gain Kp and integral time Ti.The S-shaped waveform can be defined by two parameters, delay time L and time constant T as illustrated in Figure 11a.10a and has an error of 33.26% with a peak overshoot of 62.7284%.In Figure 10b, the response settles at −0.9993 and has an error of 0.7% with a peak overshoot of 62.64644%.

Design of Controller
The most popular proportional plus integral (PI) controller has been designed to eliminate the steady state error pointed in Figure 10.One can obtain the proportional and the integral output as given in (30).
Ziegler-Nichols PI tuning was adopted to obtain the values of the proportional gain K p and integral time T i .The S-shaped waveform can be defined by two parameters, delay time L and time constant T as illustrated in Figure 11a.The designed PI controller has been incorporated with the plant as shown in Figure 11b.The parameters of the controller can be obtained as given in (34) 1 1 , 0.9 , 0.3 Figure 12a, 12b show the step response of the converter with PI controller for the step change in input sources V1 and V2 respectively.The steady state error is reduced and overshoots of 0.0013% and 0.0068% are achieved.To make both sources work effectively, with the magnitude of input voltage V1 > V2, the duty cycle is considered as δ1 < δ2.

Results and Discussion
A 100 W, 20 kHz NI-TPC converter using MOSFET switches was fabricated in the laboratory (Figure 13.) with the designed values.The whole system consists of the developed converter, two DC power sources representing the renewable energy sources such as PV and fuel cell, a FPGA spartan6 controller board, and a resistive load.Triggering signals for the switches and the controller are realized using FPGA Spartan 6 controller board.The specifications of components used are listed in Table 2.The designed PI controller has been incorporated with the plant as shown in Figure 11b.The parameters of the controller can be obtained as given in (34) Figure 12a,b show the step response of the converter with PI controller for the step change in input sources V 1 and V 2 respectively.The steady state error is reduced and overshoots of 0.0013% and 0.0068% are achieved.To make both sources work effectively, with the magnitude of input voltage V 1 > V 2 , the duty cycle is considered as δ 1 < δ 2 .The designed PI controller has been incorporated with the plant as shown in Figure 11b.The parameters of the controller can be obtained as given in (34) 1 1 , 0.9 , 0.3 Figure 12a, 12b show the step response of the converter with PI controller for the step change in input sources V1 and V2 respectively.The steady state error is reduced and overshoots of 0.0013% and 0.0068% are achieved.To make both sources work effectively, with the magnitude of input voltage V1 > V2, the duty cycle is considered as δ1 < δ2.

Results and Discussion
A 100 W, 20 kHz NI-TPC converter using MOSFET switches was fabricated in the laboratory (Figure 13.) with the designed values.The whole system consists of the developed converter, two DC power sources representing the renewable energy sources such as PV and fuel cell, a FPGA spartan6 controller board, and a resistive load.Triggering signals for the switches and the controller are realized using FPGA Spartan 6 controller board.The specifications of components used are listed in Table 2.

Results and Discussion
A 100 W, 20 kHz NI-TPC converter using MOSFET switches was fabricated in the laboratory (Figure 13.) with the designed values.The whole system consists of the developed converter, two DC power sources representing the renewable energy sources such as PV and fuel cell, a FPGA spartan6 controller board, and a resistive load.Triggering signals for the switches and the controller are realized using FPGA Spartan 6 controller board.The specifications of components used are listed in Table 2. Experiments have been conducted using the proposed NI-TPC converter with an 18 V input voltage.Duty ratios of 60% and 40% were chosen for the boost and buck operations respectively.The results are shown in Figures 14 and 15.Also, the test has been performed with 12 V input voltage and observed that the performance is satisfying the theoretical analysis.However, these results are not provided in this paper.
Figure 14a shows the current through inductors L1, L2 and the load current I0 along with gate signal applied under boost operation.It can be seen that the current ripples of inductors ΔiL1, ΔiL2 and load current Δi0 are in between (5.9 A, 5.   Experiments have been conducted using the proposed NI-TPC converter with an 18 V input voltage.Duty ratios of 60% and 40% were chosen for the boost and buck operations respectively.The results are shown in Figures 14 and 15.Also, the test has been performed with 12 V input voltage and observed that the performance is satisfying the theoretical analysis.However, these results are not provided in this paper.
Figure 14a shows the current through inductors L 1 , L 2 and the load current I 0 along with gate signal applied under boost operation.It can be seen that the current ripples of inductors ∆i L1 , ∆i L2 and load current ∆i 0 are in between (5.9 A, 5.  Experiments have been conducted using the proposed NI-TPC converter with an 18 V input voltage.Duty ratios of 60% and 40% were chosen for the boost and buck operations respectively.The results are shown in Figures 14 and 15.Also, the test has been performed with 12 V input voltage and observed that the performance is satisfying the theoretical analysis.However, these results are not provided in this paper. Figure 14a shows the current through inductors L1, L2 and the load current I0 along with gate signal applied under boost operation.It can be seen that the current ripples of inductors ΔiL1, ΔiL2 and load current Δi0 are in between (5.9 A, 5.The performance of the converter was tested in DISO mode and the corresponding voltage and current signals are shown in Figure 16.The current through the inductors L1 and L3 with gate signal applied to both the switches are shown in Figure 16a.The inductor currents iL2 and i0 are shown in Figure 16b.It can be observed that the average inductor currents are matching with results from (3), ( 14) and ( 15) and ripples are slightly more than the designed value of 5%.The voltage across the capacitors C1 and C2 are 40 V and 34 V respectively as shown in Figure 16c.It can be seen that the ripples of capacitors are within (36.5 V, 44.5 V) for C1 and (31.5 to 39 V) for C2.The obtained voltage ripples (approximately 10%) are more than the designed value (5%).However, it can be observed that the current of all the ports, IL1, IL2 and I0 are continuous with less ripples.Figure 15a shows the current through the inductors L 1, L 2 and load current 1.4 A, 2.2 A and 2.17 A, under step down mode, which are closer to 1.39 A, 2.08 A, and 2.08 A calculated from (2) and (3).The corresponding ripples ∆i L1 , ∆i L2 and ∆i 0 are within (1.55, 1.25 A), (2.4 and 2.0 A) and (2.3 and 2.1 A) respectively.It is found that the ripples are slightly more than the designed value of 5%.The voltage ripples of the capacitor are shown in Figure 15b.It can be seen that the ripples of capacitors are within (28.8, 29.55 V) for C 1 and (11.0 to 11.4 V) for C 2 .The gate signal, source and output voltages are 15 V, 18 V and −11.2 V respectively, as shown in Figure 15c.
The performance of the converter was tested in DISO mode and the corresponding voltage and current signals are shown in Figure 16.The current through the inductors L 1 and L 3 with gate signal applied to both the switches are shown in Figure 16a.The inductor currents i L2 and i 0 are shown in Figure 16b.It can be observed that the average inductor currents are matching with results from (3), ( 14) and ( 15) and ripples are slightly more than the designed value of 5%.The voltage across the capacitors C 1 and C 2 are 40 V and 34 V respectively as shown in Figure 16c.It can be seen that the ripples of capacitors are within (36.5 V, 44.5 V) for C 1 and (31.5 to 39 V) for C 2 .The obtained voltage ripples (approximately 10%) are more than the designed value (5%).However, it can be observed that the current of all the ports, I L1 , I L2 and I 0 are continuous with less ripples.
The response of the converter during transient load condition is shown in Figure 17.The load is varied to increase the load current from 0.6 A to 3.8 A. Approximately 20 s later, the load decreased to 0.8 A from 3.8 A. In both the cases, it is observed that the load voltage is regulated at 23.9 V which is closer to the desired value of 24 V.The load voltage magnitude is shown positive by using the probe with opposite polarity.The response of the converter during transient load condition is shown in Figure 17.The load is varied to increase the load current from 0.6 A to 3.8 A. Approximately 20 seconds later, the load decreased to 0.8 A from 3.8 A. In both the cases, it is observed that the load voltage is regulated at 23.9 V which is closer to the desired value of 24 V.The load voltage magnitude is shown positive by using the probe with opposite polarity.The response of the converter during transient load condition is shown in Figure 17.The load is varied to increase the load current from 0.6 A to 3.8 A. Approximately 20 seconds later, the load decreased to 0.8 A from 3.8 A. In both the cases, it is observed that the load voltage is regulated at 23.9 V which is closer to the desired value of 24 V.The load voltage magnitude is shown positive by using the probe with opposite polarity.18a,b present the comparison plot between the theoretical, simulation and experimental absolute values of voltage gains as a function of duty ratio for SISO and DISO modes, respectively.It is obvious that both the theoretical and experimental voltage gains are increasing as the duty ratio increases.In addition, the voltage gain obtained from the experiment closely approximates the theoretical and the simulation results between 0.3 and 0.5, whereas a slight deviation has been observed in the duty ratio beyond 0.5 with increasing voltage difference.It is worth mentioning that this difference is due to the component losses.
the duty ratio increases.In addition, the voltage gain obtained from the experiment closely approximates the theoretical and the simulation results between 0.3 and 0.5, whereas a slight deviation has been observed in the duty ratio beyond 0.5 with increasing voltage difference.It is worth mentioning that this difference is due to the component losses.Thus, the results validate the theoretical analysis and show the good feasibility of expected operation.Several tests are conducted and the maximum efficiency between the modes has been compared and plotted in a graph as shown in Figure 19, and the observed efficiencies for Mode 1 (SISO) with V1 and V2 sources are 92.74% and 91.15% respectively, and for Mode 2 is 90.43%.Comparing with efficiencies obtained through simulation, efficiencies for Mode 1 (SISO) with individual contribution of V1 and V2 sources are 94.13% and 93.66%, respectively, and for Mode 2 is 92.21%.Table 3 presents the comparison of various TP-NI converters with the proposed one.It is clear that the proposed converter provides continuous current at all the ports with a reduction in components.Thus, the results validate the theoretical analysis and show the good feasibility of expected operation.Several tests are conducted and the maximum efficiency between the modes has been compared and plotted in a graph as shown in Figure 19, and the observed efficiencies for Mode 1 (SISO) with V 1 and V 2 sources are 92.74% and 91.15% respectively, and for Mode 2 is 90.43%.Comparing with efficiencies obtained through simulation, efficiencies for Mode 1 (SISO) with individual contribution of V 1 and V 2 sources are 94.13% and 93.66%, respectively, and for Mode 2 is 92.21%.Table 3 presents the comparison of various TP-NI converters with the proposed one.It is clear that the proposed converter provides continuous current at all the ports with a reduction in components.

Conclusion
In this paper a NI-TPC converter is synthesized using conventional Cuk converters to interface RS like Fuel cell and PV source.The operational modes and analysis of the converter are discussed in detail.Fewer active and passive components and a shared output inductor are the advantages of this converter.The continuous input and output currents are achieved owing to the presence of inductors.Therefore, this converter is appropriate for FC power supplies that necessitates continuous current with low ripple.The simulation and experimental results are provided to verify the feasibility of the proposed converter.

Conclusions
In this paper a NI-TPC converter is synthesized using conventional Cuk converters to interface RS like Fuel cell and PV source.The operational modes and analysis of the converter are discussed in detail.Fewer active and passive components and a shared output inductor are the advantages of this converter.The continuous input and output currents are achieved owing to the presence of inductors.Therefore, this converter is appropriate for FC power supplies that necessitates continuous current with low ripple.The simulation and experimental results are provided to verify the feasibility of the proposed converter.

Figure 3 .
Figure 3. Generalized structure of the proposed 'n' port converter.

Figure 3 .
Figure 3. Generalized structure of the proposed 'n' port converter.

Figure 8 .
Figure 8. Voltage gain Vs Duty cycle of NI-TPC converter.

Figure 8 .
Figure 8. Voltage gain Vs Duty cycle of NI-TPC converter.

Figure 9 .
Figure 9. Waveforms of various voltages and currents during mode 2 (a,f) Gate signal to S1, (b,g) Gate signal to S2, (c) Voltage across capacitor C1, (d) Voltage across capacitor C2 (e) Current through the inductor i3 (h) Output voltage (i) Current through the inductor L1 (j) Current through the inductor L2.

Figure 9 .
Figure 9. Waveforms of various voltages and currents during mode 2 (a,f) Gate signal to S 1 , (b,g) Gate signal to S 2 , (c) Voltage across capacitor C 1 , (d) Voltage across capacitor C 2 , (e) Current through the inductor i 3 , (h) Output voltage (i) Current through the inductor L 1 , (j) Current through the inductor L 2 .

Figure 10 .
Figure 10.Step response of open loop system (a) with V1 source and (b) with V2 source.

Figure 10 .
Figure 10.Step response of open loop system (a) with V 1 source and (b) with V 2 source.

Figure
Figure10a,b depicts the step response of the converter with step change in input sources V 1 and V 2 respectively.It is clear that the response is inverted as the Cuk converter has inverted output.The steady state value settles at −0.6674 in Figure10aand has an error of 33.26% with a peak overshoot of 62.7284%.In Figure10b, the response settles at −0.9993 and has an error of 0.7% with a peak overshoot of 62.64644%.

Figure 12 .
Figure 12.Step response of the system in closed loop (a) with V1 source and (b) with V2 source.

Figure 12 .
Figure 12.Step response of the system in closed loop (a) with V1 source and (b) with V2 source.

Figure 12 .
Figure 12.Step response of the system in closed loop (a) with V 1 source and (b) with V 2 source.
3 A), (4.3 A, 3.4 A) and (4.2 A, 3.4 A) respectively.The average values and ripples are in close approximation with the 5.55 A, 3.71 A, and 3.6 A calculated from (2) and (3).The voltage across the capacitors C1 and C2 along with gate signal are shown in Figure 14b.From Figure 14b, the average voltages across the capacitors are 44 V and −26.2V which are in agreement with the theoretical calculations from (1) and (2).The generated gate signal and source and output voltages are 15V, 18V, and −26.2V, respectively, as shown in Figure 14c.
3 A), (4.3 A, 3.4 A) and (4.2 A, 3.4 A) respectively.The average values and ripples are in close approximation with the 5.55 A, 3.71 A, and 3.6 A calculated from (2) and (3).The voltage across the capacitors C 1 and C 2 along with gate signal are shown in Figure 14b.From Figure 14b, the average voltages across the capacitors are 44 V and −26.2 V which are in agreement with the theoretical calculations from (1) and (2).The generated gate signal and source and output voltages are 15 V, 18 V, and −26.2 V, respectively, as shown in Figure 14c.
3 A), (4.3 A, 3.4 A) and (4.2 A, 3.4 A) respectively.The average values and ripples are in close approximation with the 5.55 A, 3.71 A, and 3.6 A calculated from (2) and (3).The voltage across the capacitors C1 and C2 along with gate signal are shown in Figure 14b.From Figure 14b, the average voltages across the capacitors are 44 V and −26.2V which are in agreement with the theoretical calculations from (1) and (2).The generated gate signal and source and output voltages are 15V, 18V, and −26.2V, respectively, as shown in Figure 14c.

Figure 17 .
Figure 17.Voltages and currents from the experiment during transient condition.Input voltage, input current, load voltage and current (CH 1-4).

Figure 18a ,
Figure 18a, 18b present the comparison plot between the theoretical, simulation and experimental absolute values of voltage gains as a function of duty ratio for SISO and DISO modes, respectively.It is obvious that both the theoretical and experimental voltage gains are increasing as

Figure 16 .
Figure 16.Various voltage and current measurements from experiments during Mode 2 with both sources: (a) Gate pulses of both switches and inductor currents through L 1 and L 3 (CH 1-4); (b) Gate pulses of switches , inductor currents through L 2 and L 0 (CH 1-4); (c) Gate signals of S 1 and S 2 , and capacitor voltages across C 1 and C 2 (CH 1-4).

Figure 17 .
Figure 17.Voltages and currents from the experiment during transient condition.Input voltage, input current, load voltage and current (CH 1-4).

Figure 18a ,
Figure 18a, 18b present the comparison plot between the theoretical, simulation and experimental absolute values of voltage gains as a function of duty ratio for SISO and DISO modes, respectively.It is obvious that both the theoretical and experimental voltage gains are increasing as

Figure 17 .
Figure 17.Voltages and currents from the experiment during transient condition.Input voltage, input current, load voltage and current (CH 1-4).

Figure 18 .
Figure 18.Voltage gain as a function of duty cycle (a) SISO mode (b) DISO mode.

Figure 18 .
Figure 18.Voltage gain as a function of duty cycle (a) SISO mode (b) DISO mode.

Figure 19 .
Figure 19.Maximum efficiency for various modes.

Table 1 .
Comparison of circuit elements.

Table 1 .
Comparison of circuit elements.

Table 1 .
Comparison of circuit elements.

Table 2 .
Components of the proposed converter.

Table 3 .
Comparison of converters.

Table 3 .
Comparison of converters.