Constant Envelope Modulation Techniques for Limited Power Millimeter Wave Links

: The demand for increased capacity and link availability for mobile communications requires the utilization of higher frequencies, such as millimeter waves at extremely high frequencies (EHFs) above 30 GHz. In this regime of frequencies, the waves are subjected to high atmospheric attenuation and dispersion e ﬀ ects that lead to a degradation in communication reliability. The fact that solid-state millimeter and sub-millimeter wave sources are producing low power calls for e ﬀ ective signaling utilizing waveforms with a low peak to average power ratio (PAPR), such as constant envelope (CE) modulation. The CE techniques present a PAPR of 0 dB resulting in peak power transmission with high energy e ﬃ ciency. The study of the performances of constant envelope orthogonal modulation techniques in the presence of co-channel interference is presented. The performance is evaluated in terms of the average symbol error rate (SER) using analytical results and simulations. The theory is carried out for the CE-M-ary time orthogonal (CE-MTO) and CE-orthogonal frequency division multiplexing (CE-OFDM), demonstrating comparable performances while leading to a simpler implementation than that of the CE-OFDM.

(H2O) occurs; as well as absorption peaks at 60 and 119 GHz, due to the absorption resonances of oxygen (O2) [46][47][48]. A minimum attenuation is obtained at atmospheric transmission "windows" in the Ka-(35 GHz) and W-bands (94 GHz), as well in the vicinity of 130 and 220 GHz [37]. The gray bands represent the spectrum allocated for the 5G. In Figure 1b, we show the incremental group delay (in ps/km) caused by the phase variation in the frequency. The atmospheric transfer characteristics can be calculated for any value of the relative humidity (RH). When carrying out a link budget, the atmospheric attenuation must be taken into account. In millimeter wave links, the antennas are usually directive, resulting mainly in line-of-sight (LOS) paths. When a transmitter (T; with an effective isotropic radiated power ( T EIRP )) and an interferer (I; with I EIRP ) transmit a signal to a receiver in their LOS (see Figure 2), the corresponding power from the transmitting station is as follows: and from the interferer station, it is as follows: When carrying out a link budget, the atmospheric attenuation must be taken into account. In millimeter wave links, the antennas are usually directive, resulting mainly in line-of-sight (LOS) paths. When a transmitter (T; with an effective isotropic radiated power (EIRP T )) and an interferer (I; with EIRP I ) transmit a signal to a receiver in their LOS (see Figure 2), the corresponding power from the transmitting station is as follows: and from the interferer station, it is as follows: where G R is the receiver antennas gain, λ = c/ f is the wavelength of the transmitted signal (c is the speed of light, f is the frequency), d TR and d TI are the distances between the transmitter or interferer to the receiver, respectively, and 2α( f ) is the power attenuation factor caused by the atmospheric medium. The signal to interference power ratio at the receiver site is given by the following:

Error Rate Degradation in the Presence of Co-Channel Interference
Co-channel interference occurs between two transmitters that are using the same frequency. The co-channel interference can severely affect the performance of the symbol error rate (SER). In this section, the SER performance properties of the CE-MTO and the CE-OFDM in the presence of cochannel interference are studied.
The signal arriving at the receiver from the transmitter is a constant envelope phase-modulated waveform. Its complex amplitude at baseband is given by the following [25]: where 1 j = − and Ac is the (constant) signal envelope. ( ) t φ is the information-bearing message phase. Assuming an in-band interference, its respective complex amplitude is as follows: with the power given by the variance, as follows: where we define SIR as the signal to interference power ratio at the receiver site, as in Equation (3).
The interfering signal phase, ( ) t θ , is a stochastic process that is uniformly distributed ( ) , π π − . Both the signal and interference are received simultaneously, resulting in a composite waveform, written as follows: where its phase is as follows:

Error Rate Degradation in the Presence of Co-Channel Interference
Co-channel interference occurs between two transmitters that are using the same frequency. The co-channel interference can severely affect the performance of the symbol error rate (SER). In this section, the SER performance properties of the CE-MTO and the CE-OFDM in the presence of co-channel interference are studied.
The signal arriving at the receiver from the transmitter is a constant envelope phase-modulated waveform. Its complex amplitude at baseband is given by the following [25]: where j = √ −1 and A c is the (constant) signal envelope. φ(t) is the information-bearing message phase. Assuming an in-band interference, its respective complex amplitude is as follows: with the power given by the variance, as follows: where we define SIR as the signal to interference power ratio at the receiver site, as in Equation (3). The interfering signal phase, θ(t), is a stochastic process that is uniformly distributed (−π, π). Both the signal and interference are received simultaneously, resulting in a composite waveform, written as follows: where its phase is as follows: Note that when SIR → ∞ , the resulted phase isφ(t) = φ(t), equal to that of the required signal, as expected. In order to calculate the interference component in the phase, we assume φ(t) = 0. In this case, the phase fluctuation due to the interferer is as follows: Further analysis considers the detection of orthogonal modulation techniques (CE-OFDM [25] and CE-MTO [26] techniques). In the receiver (see Figure 3), after an analog to digital conversion, the samples, r[n], are sent to the phase demodulator. The output of the phase demodulator in the continuous-time presentation isφ(t) = φ(t) + ξ(t), where ξ(t) is the phase interference component given by Equation (9). The amplitude is kept constant by a limiter. A set of matched filters calculate the correlations, as follows: , h is the modulation index, and C is a constant used to normalize the variance of the resulted phase, namely: , where M is the pulse-amplitude modulation (PAM) constellation, I k is the N real valued data symbols, and q k [n] is the discrete orthogonal waveforms. In the CE-OFDM technique, q k [n] is the orthogonal subcarriers' quadrature components, while in CE-MTO q k [n] is the orthogonal series generated by the Hadamard matrix. S[k] is the signal component, as follows: where d = 2πhCq, and for the CE-MTO case, C = 3/N(M 2 − 1) andq = N chip , where N chip is the number of chips contained in the orthogonal waveforms, q k [n]. For the CE-OFDM case, is the number of points in the inverse discrete Fourier transformation (IDFT). The interference component in Equation (10) is as follows: As ξ[n] is the independent random values, the sum of Equation (12) where in our case, we have the following: The substitution of Equation (6) in Equation (14), and σ I and d in Equation (13), results, for both CE-MTO and CE-OFDM, in the following: case, the phase fluctuation due to the interferer is as follows: Further analysis considers the detection of orthogonal modulation techniques (CE-OFDM [25] and CE-MTO [26] techniques). In the receiver (see Figure 3), after an analog to digital conversion, the samples, [ ] r n , are sent to the phase demodulator. The output of the phase demodulator in the given by Equation (9)   A comparison is made between the analytical results obtained using Equation (15) and those obtained from simulations of the CE-MTO and the CE-OFDM demodulation in the presence of external interference. Figure 4 shows the graphs of the SER as a function of the SIR. The correlations between the graphs are revealed. The graphs were drawn assuming N chip = 16 chips for each of the N = 14 orthogonal waveforms. Several PAM constellation orders, M = 4, 8, and 16, wre considered. In order to keep the bandwidth restrained, the modulation index is set to 2πh = 0.4, 0.5, and 0.6.  . Based on the literature [25], we may approximate SER as follows: where in our case, we have the following: The substitution of Equation (6) in Equation (14), and σ Ι and d in Equation (13), results, for both CE-MTO and CE-OFDM, in the following: A comparison is made between the analytical results obtained using Equation (15) and those obtained from simulations of the CE-MTO and the CE-OFDM demodulation in the presence of external interference. Figure 4 shows the graphs of the SER as a function of the SIR. The correlations between the graphs are revealed. The graphs were drawn assuming

Performance of AWGN Channel in the Presence of CCI
In the presence of additive white Gaussian noise, ( ) n t , in addition to the interference (see A comparison is made between the analytical results obtained using Equation (18) and the simulation results of the CE-MTO and the CE-OFDM techniques in the presence of external interference and AWGN. Figure 5 shows the simulated results for the SER as a function of the

Performance of AWGN Channel in the Presence of CCI
In the presence of additive white Gaussian noise, n(t), in addition to the interference (see Figure 3), the received signal can be written as follows: Due to the fact that ι(t) and n(t) are independent random processes, that is, σ 2 I+N = σ 2 I + σ 2 N , where the AWGN standard deviation is based on the following [26]: Here, E b is the energy per bit of the transmitted signal and N 0 is the power spectral density (PSD) of the AWGN. In order to calculate the SER analytical expression of this new scenario, the expression of (13) is used, leading to: A comparison is made between the analytical results obtained using Equation (18) and the simulation results of the CE-MTO and the CE-OFDM techniques in the presence of external interference and AWGN. Figure 5 shows the simulated results for the SER as a function of the E b /N 0 . It is noticeable that there is a high correlation between the simulated results for both modulation techniques (CE-OFDM and CE-MTO).  . The signal to interference power ratio is assumed to be SIR = 15 dB. The "Analytical AWGN only" curve refers to the analytical expression obtained in our previous work [26] in Equation (21) for the case of the AWGN channel only. The "Analytical Interference only" and the "Analytical Interference and AWGN" curves refer to Equations (15) and (18), respectively. Figure 5 shows that for the case of SIR = 15 dB, M = 4, and 2 0.6 h π = , the SER for the "Analytical Interference only" is approximately equal to 0.025. Please note the "Analytical AWGN only" and the "Analytical Interference only" curves function as an asymptote for the "Simulated" and "Analytical Interference and AWGN" graphs in which the interference and AWGN exists.

Results for Different CCI Scenarios
The simulation results for the different CCI scenarios are presented in the following. First, it is assumed that the interferer transmits at the very same frequency as the required transmission. Then, a frequency shift, f Δ , is introduced to the interferer carrier.
The analytical Equation (18) for the SER in the presence of interference and AWGN depends on the signal to interference (SIR) power ratio at the receiver, on the modulation index ( 2 h π ), and the constellation order (M). The case when the carrier frequencies of the transmitter and the interferer are identical is studied. Note that for Figure 6, the "Analytical AWGN only" curve refers to the situation where the PAM constellation order is M = 4 and the modulation index is 2 0.6 h π = . In Figure 6a, we show the dependence on the SIR parameter. As expected, a higher SIR results in a lower SER. Figure 6b shows the SER dependence on the modulation index, 2 h π . As the value of 2 h π is increased, the SER decreases. Finally, Figure 6c demonstrates the dependence on the constellation M. Smaller constellations show a better performance. The graphs in Figure 5 have been created for N = 14 orthogonal waveforms, each containing N chip = 16 chips. The PAM constellation order is M = 4 and the modulation index is kept at 2πh = 0.6. The signal to interference power ratio is assumed to be SIR = 15 dB. The "Analytical AWGN only" curve refers to the analytical expression obtained in our previous work [26] in Equation (21) for the case of the AWGN channel only. The "Analytical Interference only" and the "Analytical Interference and AWGN" curves refer to Equations (15) and (18), respectively. Figure 5 shows that for the case of SIR = 15 dB, M = 4, and 2πh = 0.6, the SER for the "Analytical Interference only" is approximately equal to 0.025. Please note the "Analytical AWGN only" and the "Analytical Interference only" curves function as an asymptote for the "Simulated" and "Analytical Interference and AWGN" graphs in which the interference and AWGN exists.

Results for Different CCI Scenarios
The simulation results for the different CCI scenarios are presented in the following. First, it is assumed that the interferer transmits at the very same frequency as the required transmission. Then, a frequency shift, ∆ f , is introduced to the interferer carrier.
The analytical Equation (18) for the SER in the presence of interference and AWGN depends on the signal to interference (SIR) power ratio at the receiver, on the modulation index (2πh), and the constellation order (M). The case when the carrier frequencies of the transmitter and the interferer are identical is studied. Note that for Figure 6, the "Analytical AWGN only" curve refers to the situation where the PAM constellation order is M = 4 and the modulation index is 2πh = 0.6. In Figure 6a, we show the dependence on the SIR parameter. As expected, a higher SIR results in a lower SER. Figure 6b shows the SER dependence on the modulation index, 2πh. As the value of 2πh is increased, the SER decreases. Finally, Figure 6c demonstrates the dependence on the constellation M. Smaller constellations show a better performance.
Interferer shift in frequency results in phase θ(t) = 2π∆ f t, where ∆ f is the difference in carrier frequencies. Figure 7 presents the spectrum of the CE-OFDM, CE-MTO, and the CW interference. Note that for the CE-MTO, T chip is the time duration of a series "chip", while for the CE-OFDM, T chip = T symbol /N, where N is the number of subcarriers. The inspection of Figure 7 reveals that the CE-MTO spectrum is null for the ∆ f · T chip = integer. The interference is located at ∆ f · T chip = 2. Comparing the two modulation techniques reveals a slight difference between the spectrum of the CE-OFDM and that of the CE-MTO.      Figure 8a-c have been obtained for N = 14 orthogonal waveforms of N chip = 16 chips. The order constellation is M = 4 and the modulation index is 2πh = 0.6. It is assumed that the signal to interference power ratio is SIR = 15 dB for different frequency shift values, ∆ f · T chip . In Figure 8a, where ∆ f · T chip = 0.3, the performance of CE-MTO is revealed to be better than that of CE-OFDM. However, in Figure 8b, where ∆ f · T chip = 0.6, the CE-OFDM demonstrates a better performance than that of CE-MTO. The curves in Figure 8c refer to ∆ f · T chip = 1. In this scenario, the performance of CE-MTO and that of CE-OFDM are identical. The results obtained in Figure 8a-c are as expected when examining the spectrum as given in Figure 7.
MTO spectrum is null for the chip f T Δ ⋅ = integer. The interference is located at 2 chip f T Δ ⋅ = . Comparing the two modulation techniques reveals a slight difference between the spectrum of the CE-OFDM and that of the CE-MTO.

Summary and Conclusions
Small PAPR modulation schemes are being used for better power efficiency. In CE-OFDM, the carrier is phase-modulated with the OFDM signaling to generate a constant envelope waveform. CE-MTO is a new suggested technique for constant envelope modulation, which is based on orthogonal waveforms in the time domain, and with the implementation expected to be simpler than that of the CE-OFDM. An analytical expression for the SER performance degradation caused by the co-channel interference in different scenarios is presented. It is shown that the SER decreases in the presence of interference when the modulation index is increased. The SER grows the higher the constellation order.

Conflicts of Interest:
The authors declare no conflict of interest.