A W -Band Chebyshev Waveguide Bandpass Filter with Wide Stopband Performance

: In this paper, a W -band waveguide bandpass ﬁ lter with a standard fourth-order Cheby-shev response is proposed based on the computer numerical control (CNC)-milling technology. The harmonics-staggered technique and orthogonal coupling method are incorporated into this wave-guide ﬁ lter design without increasing the complexity of the ﬁ lter structure in order to suppress the intrinsic spurious responses near the passband. Furthermore, the proposed ﬁ lter design maintains a simple construction, which can be conveniently fabricated using CNC milling. The fabricated waveguide ﬁ lter exhibits an average insertion loss of 0.9 dB and a return loss of above 20 dB in a 3 dB fractional bandwidth (FBW) of 5.5% centered at 85 GHz. The excellent spurious suppression property can reach be tt er than − 25 dB up to 165 GHz. The wide stopband performance of the proposed W -band ﬁ lter is very competitive compared with the reported waveguide ﬁ lters.


Introduction
Millimeter-wave (mmWave) and terahertz (THz) bands have been widely used for various areas including wireless communications [1], imaging radars [2], radio astronomy [3] and atmospheric science [4].For instance, wireless communication around 100 GHz, which can offer the potential for massive data rates and broad bandwidth, has attracted considerable attention for beyond 5G and 6G communications [1,5].The interest in modern mmWave and THz communication systems and spectrum detectors has enabled a great demand for abundant active and passive devices, such as oscillators [6], multipliers [7], mixers [8], on-chip amplifiers [9], antenna arrays [10] and filters [11].Filters, as one of the key devices, can play an invaluable role in most systems, blocking unwanted or spurious waves [12].It is remarkable that the W-band from 75 to 110 GHz is an important frequency window spectrum for multi-domain applications.Therefore, fast-developing wireless communication systems at the W-band have driven a growing demand for bandpass filters (BPFs) with high performance, such as low loss, high out-of-band rejection and wide stopband.
In modern wireless communication systems, the presence of multiple signal frequencies can significantly degrade the communication quality of the overall system.Moreover, spurious signals and harmonics within RF components can adversely affect the performance of mixers and receivers.Therefore, it is essential to develop waveguide BPFs with superior stopband suppression capabilities to address these challenges.However, spurious bands caused by the intrinsic harmonics of waveguide resonators always exist, resulting in poor and narrow upper stopband performance.In the microwave band, a variety of designs have been presented to improve the stopband performance for waveguide filters such as cascading lowpass filters [32][33][34][35][36].However, these methods cannot be directly scaled up to the W-band waveguide filters because of the structure complexity [32,33] and multi-order cavities [36].
In this article, a W-band Chebyshev waveguide BPF with excellent stopband suppression performance is designed.The method of controlling both harmonics and couplings is used to realize the extended stopband in the D-band.In addition, the proposed fourthorder waveguide BPF can be easily implemented by the CNC milling technique, maintaining a low-loss feature.

Spurious Suppression Methods
This section discusses two methods for the spurious suppression of waveguide BPF based on the coupling resonator cavities.

Harmonic-Staggered Method
For most waveguide filter designs [18][19][20][21][22][23][24][25][26][27][28][29][30][31], the fundamental TE101 mode is generally considered to construct the filter passband.Each resonator cavity can support multiple harmonic resonances due to high-order modes; however, it will lead to introducing undesired passbands [21,36].The equivalent circuit diagram is shown in Figure 1, where it considers the dominant passband and spurious passbands.Usually, the high-order resonant modes such as TE102, TE201 or TE103 are regarded for coupling to the spurious passbands.Therefore, the idea for breaking spurious passbands to improve stopband performance is mainly focusing on the control of the harmonic modes or the coupled mechanism.As shown in Figure 1, the first way is staggering the intrinsic high-order harmonics, which are marked as the purple symbol "×".For a resonator cavity with a size of a × b × l, the TE101 and TEm0n modes can be calculated by the following equations, where a and l are the width and length of the cavity along the x-axis and y-axis, respectively.Following (1), the first harmonic passband is usually generated by the TE102 or TE201 mode.Constructions with different ratios of a to l can be controlled to obtain staggered high-order harmonics, i.e., different . Accordingly, Figure 2 gives the normalized frequency distributions of several high-order modes (TEm0n) and the fundamental mode f0 (TE101) in two different cavities.The constitutive resonators are selected at the points of ratio = 1.38 and ratio = 1.58,where   In order to verify the effectiveness of the above discussed harmonic-staggered technology, Structure-I with two resonators of ratio = 1.58 as well as Structure-II with one resonator of ratio = 1.58 and the other resonator of ratio = 1.38 are constructed, as shown in Figure 3a,b, respectively.Figure 4 illustrates the frequency response comparisons of Structure-II with Structure-I, where the amplitude of the first spurious passband caused by the TE102/TE201 mode can be suppressed by about 6 dB.

Harmonic-Coupling Control Scheme
The second effective method is to break or modify the coupling paths of harmonics to eliminate spurious passbands.The coupling coefficient between resonators depends on the strength of the tangential component of magnetic field or the normal component of electric field [12].The magnetic field distributions of the first four modes (TE101, TE102, TE201 and TE202) in a square resonator cavity with a ratio = 1.58 are simulated by Ansys HFSS, as shown in Figure 5.For the TE101 mode, there are four regions with the strongest magnetic field (Hx and Hy) in the middle of all edges.For the higher mode TE102 or TE201, the maximum magnetic field only appears along the x-or y-direction, and the minimum magnetic field occurs along the edge of the x-or y-direction, as clearly displayed in Figure 5. Accordingly, by means of the orthogonal couplings, neither the TE102 mode nor TE201 mode can be effectively excited.This property can be confirmed by the simulation of the Structure-III model presented in Figure 3c. Figure 6 illustrates the frequency response comparison of Structure-III with Structure-I.It is seen that the first spurious passband caused by the TE102 or TE201 mode can be greatly suppressed at the specific frequency, but the spurious passband response cannot be eliminated, which is just moved to higher frequency.Additional multiple resonators should be employed to completely eliminate the spurious passband [32], but it will increase the overall insertion loss at the working frequencies.
There is a more practical approach for fully suppressing spurious passbands based on the orthogonal architecture design [37].The asymmetry between TE102 and TE201 modes after coupling addition can be compensated by moving orthogonal ports away from the middle position with a slight shift, as shown in Figure 3d.From the response comparison of Structure-I, -III and -IV in Figure 6, it is evidently clear that the first spurious passband around 120 GHz can be significantly suppressed to exhibit much better stopband performance.It is worth noting that some other harmonics at higher than 1.5f0 frequencies still exist.

Filter Design
In this section, a fourth-order waveguide filter with a symmetrical Chebyshev in the W-band is developed to verify the usefulness of the above-mentioned spurious passband suppression methods in improving the stopband performance, according to the following specifications: (1) Center frequency f0 ≈ 85 GHz (W-band); (2) 3 dB bandwidth FBW ≈ 5%; (3) In-band return loss better than −20 dB; (4) Very wide out of band up to 2 f0.As shown in Figure 7, this geometric configuration of the W-band filter comprises two standard WR-10 waveguides (a × b = 2.54 mm × 1.27 mm), two cavities with ratio = 1.38 (Resonator-1 and Resonator-4) and two resonators with ratio = 1.58 (Resonator-2 and Resonator-3).Obviously, the first strategy is employing four resonators with different ratios to stagger the high-order harmonics to destroy the spurious passbands.The second strategy is using the folded structure to form the orthogonal couplings to decrease the unwanted TE102 nor TE201-mode responses and meanwhile obtain a compact structure, as revealed in Figure 7.The adjacent resonators, namely Resonator-1 and -2, Resonator-2 and -3 and Resonator-3 and -4, are directly magnetic couplings, which are implemented by the classical H-plane irises.It should be noted that there are no cross-couplings in this filter; as a result, a typical Chebyshev response will be obtained [12].The third strategy is shifting certain couplings to compensate coupling orthogonality to completely eliminate the spurious passbands from the f0 to 2f0 band.In this design, the couplings between the input waveguide and Resonator-1, Resonator-2 and 3, as well as Resonator-4 and the output waveguide are shifted, as indicated in Figure 7.All the vertical corners have been filleted with a 0.2 mm radius (R), which is necessary for such a high-frequency filter considering the non-negligible drill size, as shown in Figure 7. Therefore, the previously discussed methods including the harmonics-staggered technique and orthogonal coupling method have been incorporated into this waveguide filter design without increasing the complexity and difficulty of the structure.Several structural ways have been used in this design, while no other theory would be involved.Therefore, this filter design can be realized by using the well-illustrated coupling matrix method [12,38,39].Based on the above specifications, the coupling coefficients of this W-band filter can be synthesized in Table 1 and then be transformed into physical dimensions according to the procedure.Thus, most of the initial parameters of this filter can be acquired.In the last step, the shift value would be conveniently obtained using the commercial simulator ANSYS HFSS while all the other parameters are kept unchanged.The final step is only used to improve the stopband performance, while the variation in passband is almost negligible.After a fine-tuning optimization procedure in ANSYS HFSS, the final dimensions of the proposed W-band waveguide filter are tabulated in Table 2.The proposed W-band waveguide filter was fabricated in an aluminum (Al) block based on the H-plane split method by the CNC-milling technology, as shown in Figure 8.The whole filter structure was machined within one block to avoid the problems of misalignment and high aspect ratio.The minimum radius of drills during the milling process is 0.2 mm, which has been taken into account in the simulation.The assembled Al block has a volume of W × L × H = 20 × 20 × 20 mm 3 , as shown in Figure 8a. Figure 8b gives the top view microphotograph of the internal structure, where it can be seen that both the fineness and flatness are achieved to guarantee a good electrical contact.

Simulation and Measurement Results
The final simulated frequency response is shown in Figure 9 (dot dash line).It is clear that a significant wide stopband from f0 to 2f0 is obtained through such design.The spurious response suppression of better than −25 dB is greatly improved and the first spurious appears at about 165 GHz, which is twice that of the center frequency (2f0).This waveguide filter has a standard Chebyshev response with a 3 dB fractional bandwidth (FBW) of 5.5% in the W-band.Measurements of the fabricated filter were carried out by the Agilent PNA-X vector network analyzer (VNA) connecting with frequency extension modules of 75-110 GHz and 110-170 GHz, as shown in Figure 8c.The through-reflect-line (TRL) calibration was first implemented, and then the packaged block was connected and fixed to the standard waveguide converters through UG-387 flanges for measurement.The tested and simulated S-parameter results of this W-band filter are compared in Figure 9. Very good agreement between the simulations and measurements including the passband and stopband performance is observed.It can be seen from the measured results that this practical filter can provide excellent spurious suppression with −25 dB up to 2f0.The original parasitic bands that resulted from harmonic modes between f0 and 2f0 have been completely eliminated.Consequently, this filter exhibits outstanding stopband performance without introducing additional resonators, structures or losses.
In addition, as can be seen in the detailed performance in the 75-100 GHz band in Figure 10, the basically symmetrical Chebyshev response has been achieved.The simulated 3 dB FBW is about 5.5% from 83.1 to 87.8 GHz, whereas the measured 3 dB FBW is about 5.5% from 82.5 to 87.2 GHz.They are matched well with the exception of a small band shift of about 0.6 GHz (i.e., 0.7%•f0) toward low frequency, which might be due to the machining, assembly or measurement errors.The measured return loss (RL) is better than 20 dB, which is degraded slightly compared to the simulation.As shown in the bottom subfigure of Figure 10, both the actual and expected losses are at the same level in the passband.An insertion loss of about 0.9 dB has been achieved for this filter prototype.The value of 3.5 × 10 6 S/m as the equivalent conductivity has been discussed in [26,27,40], which can include multiple effects of non-ideal metallic conductors, surface roughness, electric contact, as well as other possible issues during the machining, assembling and testing process.Of course, the IL performance can be further improved by gold or copper plating within the block.Table 3 gives the performance summary of the recently reported W-band waveguide filters compared to our work.Most filters [18][19][20][21][22] have exhibited high performance, such as low loss, multiple transmission zeros and wide passband, except SIW filters [14,15] with high dielectric losses.As can been observed from Table 3, the performance including the low orders, passband width, IL and RL of our filter is comparable with the most advanced W-band filters [14,15,[18][19][20][21][22][23][24][25][26][27][28][29][30][31].Although there is no transmission zero in this filter design, the standard Chebyshev response with sharp side-bands has also been obtained, which benefits from the spurious-free response nearby the passband.This proposed waveguide filter has achieved a high rejection property out of band, especially in the wide upper stopband, and it outperformed other classical filters in such a W-band.The aforementioned results have also indicated that our proposed filter can be absolutely suitable through the CNC-machining fabrication while maintaining high performance.
In the near future, waveguide BPFs working at the W-band and above will be developed toward multiple passbands with a wider stopband.In addition, the environmental experiments including wide adaptable temperature and mass manufacturing should be explored for further design of the waveguide filter.It will provide a deeper insight into the practical development and applications of the proposed W-band BPF.

Conclusions
A W-band waveguide filter with wide stopband performance has been proposed and evaluated based on the CNC-milling technology.The intrinsic spurious responses from f0 to 2f0 can be fully eliminated using multiple spurious passband suppression methods.High performance including the standard Chebyshev response with a low IL of 0.9 dB in the W-band and excellent stopband rejection level of −25 dB have been achieved.Such a method can be even scaled up to the THz frequency band by using the advanced CNCmilling or micro-machining technologies.It is of great potential for the applications in millimeter-wave and THz waveguide components and systems.

Figure 1 .
Figure 1.Equivalent circuit diagram considering spurious passbands of the filter.
the frequency ratio of the second resonance mode to the fundamental one.It can be seen that the harmonic resfor all resonators in the filter design.

Figure 2 .
Figure 2. Normalized frequency distributions of several high-order modes in two cavities with ratio = 1.38 and ratio = 1.58.

Figure 3 .Figure 4 .
Figure 3. (a) Structure-I: BPF using two identical coupled square resonator cavities; (b) Structure-II: BPF using two different coupled resonator cavities with ratio = 1.38 and ratio = 1.58, respectively; (c) Structure-III: BPF using two coupled square resonator cavities with orthogonal coupling ports; (d) Structure-IV: BPF using two coupled square resonator cavities with orthogonal coupling ports and offset.

Figure 5 .Figure 6 .
Figure 5. Simulated magnetic-field magnitude distributions of the first four modes including TE101, TE102, TE201 and TE202 in a square resonator cavity.

Figure 7 .
Figure 7. Three-dimensional (3D) and top view of the W-band waveguide filter.

Figure 8 .
Figure 8.(a) Photograph, (b) top view photomicrograph of inside of the fabricated filter and (c) the measurement setup.

Figure 9 .
Figure 9. Simulated and measured results of this filter in the wideband of 75-170 GHz.An equivalent conductivity of 3.5 × 10 6 S/m is used in the simulation.

Figure 10 .
Figure 10.The detailed performance of this filter in full W-band.

Table 1 .
Coupling coefficients of the proposed Chebyshev filter.

Table 2 .
Parameter values of the proposed Chebyshev filter.

Table 3 .
Performance summary of W-band waveguide filters based on different technologies.