Wireless Power Transfer System with Current-Doubler Rectiﬁer on the Secondary Side—Analysis, Modeling, and Veriﬁcation

: In this paper, the proposal for the performance optimization of the wireless power transfer (WPT) system is given. The solution is based on the alternative conﬁguration of the secondary-side rectiﬁer. It is represented by a diode rectiﬁer with a current doubler. Compared to the bridge rectiﬁer, two diodes are replaced by the inductors. Initially, a system analysis was performed to investigate the electrical behavior and ﬁnd the most optimal conditions referred to as terms of efﬁciency performance at nominal power. Due to this requirement, the rectiﬁer inductors must be designed accordingly to meet this condition. The experimental veriﬁcation was realized as well, while the proposed solution was compared to other common alternatives of the secondary-side rectiﬁcation. The load sensitivity analysis in terms of efﬁciency performance was realized as well to observe the system behavior for a wide operation range. From the results, it is seen that the proposed alternative of the secondary-side rectiﬁcation of the WPT system gives promising results in terms of high operating efﬁciency.


Introduction
The wireless power transfer (WPT) system is recognized as one of the most appropriate technological approaches.WPT has already reached the commercialization stage in inductive pickup systems in manufacturing facilities [1], and it has been used in portable consumer electronics as well as for biomedical applications [2][3][4][5][6] over the last decade.Active research has recently been extended to the static and dynamic charging of electric vehicles [7,8] and medical implants [9,10].The constant power performance increase in the portable devices wireless chargers creates a significant technical approach for electrical engineers and researchers, which are associated with the effective removal of heat losses outside of the charged accumulator's area.Portable devices have a relatively low charging voltage value and thus a high current value, so together with the value of the parasitic secondary coil series resistance, significant heat losses occur [11][12][13][14][15][16].
The load resistance of a WPT system should be transformed to the optimum load resistance of the system because the WPT system transfer efficiency is highly dependent on the load impedance.Then, a high-power transfer efficiency for the whole (or most) part of the load range can be achieved.Many studies have been conducted regarding this topic [17][18][19][20][21][22][23].Generally, there are at least four commonly used methods that can realize load resistance transformation [24][25][26]:

•
Using DC-DC converters for altering load impedance; • Using passive circuits for impedance matching; • Reconfigurable resonant circuits for impedance matching;

•
Using variable operating frequency.
The key will be the nature of the used specific compensation topology for the analyzed WPT system.For example, topology series-series (S-S, compensating for the coils' own inductance), parallel-parallel (P-P), LCC-LCC, LCC-P, and others are characterized by their current output, i.e., they act as a current source.Other topologies, e.g., S-S (compensating for the stray inductance of coils), P-S, S-P, LCC-S, and others, act as a voltage source [27,28].For a specific type of output, it is most appropriate to use only a compatible current doubler.In principle, two types of current doubler are recognized: a rectifier with coils without magnetic coupling (which is suitable for WPT systems with current output) and a rectifier with magnetically coupled coils (which is suitable for WPT systems with voltage output) [29][30][31].
EVs with WPT technology usually consider their power batteries to be the energy receiving device.The output power level of the complete WPT system is tied to mutual inductance and equivalent battery resistance.The power sent to the WPT system's secondary side, which employs a bridge rectifier, is insufficient when there is a light load.The system's overall power transmission capacity has been increased through the application of numerous strategies.A novel impedance transfer method based on the combined continuous conduction mode (CCM) and discontinuous conduction mode (DCM) operating out of the buck converter is proposed [32] to track the maximum power transmission.However, the receiving side requires a buck converter, which adds to the cost and installation area of the system.It also requires a switch and three passive elements.The phase difference between the secondary rectifier input voltage and the primary inverter output voltage can be set to 90 to increase the power level, which is in accordance with the auxiliary function of an additional three-coil system [33].However, to implement the closed-loop control mechanism, wireless communication between the sending and receiving sides is necessary.Unfortunately, the extra communication facilities will result in an increase in system size and expense.Many [34][35][36] have implemented the frequency adjustment to follow the greatest power transfer as the coupling coefficient moves beyond the critical coupled state.That does, however, primarily address the issue of output power loss under various coupling coefficients.The frequency modification approach is not able to improve the output power reduction caused by the load.However, to achieve optimal coupling efficiency transmission for a specific WPT system, there exists an optimist load R opt [37][38][39].The following provides an overview of recent research on tracking maximum efficiency under load fluctuations.To attain optimal efficiency tracking, the variable load R is transferred into R opt via a DC/DC converter that is put on the secondary side.But the DC/DC converter's extra power loss, rising component costs, and large size should raise concerns.To achieve impedance matching, the passive impedance matching network-which consists of the inductor and capacitor network-is positioned in front of the rectifier component.However, there will be the introduction of the unwanted imaginary impedance.By modifying the active rectifier's phase shift angle, the equivalent impedance can be set to the ideal value for attaining the best efficiency.On the other hand, it will become more difficult to control since crossing zero-point detection is required to accurately control the phase-shift angle.
In this paper, focus is given to the performance research of a certain WPT system with a series-series compensation network [40][41][42][43][44][45] using an alternative secondary-side rectifier topology.The analysis of the impedance ratio is being evaluated in reference to the efficiency of the whole system.More specifically, according to the optimization procedure, we are talking about the possibility of replacing a standard two-way diode (or even synchronous) rectifier in a bridge connection.Using a modified rectifier on the secondary side, which is characterized by a higher impedance conversion, it is naturally possible to establish the conditions for higher achievable efficiency.This approach is favorable for the systems with a low equivalent load; thus, there is no need to consider the use of an additional power converter on the secondary side.The implementation of the proposed rectifier topology increases the voltage at the input of the rectifier, thereby reducing the current through the secondary coil.The proposed solution is analyzed to find the optimal design of the value of inductances to achieve the highest possible operational efficiency.Experimental verification is given at the end, while the analyzed solution is compared to the common configuration of the WPT system.

Analysis of Alternative Secondary-Side Rectifier
Some applications do not require regulation (based on the secondary-side load type).The analyzed system belongs to the case when no WPT system secondary-side regulation is required.For this situation, the common WPT systems use standard bridge diode rectifiers for the secondary-side rectification (Figure 1a), while C block refers to the compensation network, which can be various types.
Experimental verification is given at the end, while the analyzed solution is compared to the common configuration of the WPT system.

Analysis of Alternative Secondary-Side Rectifier
Some applications do not require regulation (based on the secondary-side load type).The analyzed system belongs to the case when no WPT system secondary-side regulation is required.For this situation, the common WPT systems use standard bridge diode rectifiers for the secondary-side rectification (Figure 1a), while C block refers to the compensation network, which can be various types.
Because wireless power transfer is currently a matter of supplying power for a wide range of applications, the consideration about the power performance is important regarding proper selection of the optimal secondary-side rectifier topology.Figure 1b shows one possible alternative topology, while upper diodes of the bridge rectifier are replaced by the inductors without any common magnetic coupling.This configuration refers to the current-type rectifier, and its operational behavior is a matter of research within this paper.

Principle of Operation of Current-Type Rectifier
To explain the operational principle of the WPT system secondary-side current-type rectifier, assumption on the harmonic power supply is made initially (Figure 2), while only the fundamental 1st harmonic is considered.In this way, a certain error is concerned regarding the mathematical model, but this error is not exceptional to prove the operational performance analysis.We are more concerned with a qualitative explanation and not with a precise mathematical description at the beginning.In addition, it would be necessary to consider the specific V-A characteristic of a certain diode.The circuit schematic for the analysis is shown in Figure 3.Because wireless power transfer is currently a matter of supplying power for a wide range of applications, the consideration about the power performance is important regarding proper selection of the optimal secondary-side rectifier topology.Figure 1b shows one possible alternative topology, while upper diodes of the bridge rectifier are replaced by the inductors without any common magnetic coupling.This configuration refers to the current-type rectifier, and its operational behavior is a matter of research within this paper.

Principle of Operation of Current-Type Rectifier
To explain the operational principle of the WPT system secondary-side current-type rectifier, assumption on the harmonic power supply is made initially (Figure 2), while only the fundamental 1 st harmonic is considered.In this way, a certain error is concerned regarding the mathematical model, but this error is not exceptional to prove the operational performance analysis.We are more concerned with a qualitative explanation and not with a precise mathematical description at the beginning.In addition, it would be necessary to consider the specific V-A characteristic of a certain diode.The circuit schematic for the analysis is shown in Figure 3.
Electronics 2023, 12, x FOR PEER REVIEW 3 of 18 additional power converter on the secondary side.The implementation of the proposed rectifier topology increases the voltage at the input of the rectifier, thereby reducing the current through the secondary coil.The proposed solution is analyzed to find the optimal design of the value of inductances to achieve the highest possible operational efficiency.Experimental verification is given at the end, while the analyzed solution is compared to the common configuration of the WPT system.

Analysis of Alternative Secondary-Side Rectifier
Some applications do not require regulation (based on the secondary-side load type).The analyzed system belongs to the case when no WPT system secondary-side regulation is required.For this situation, the common WPT systems use standard bridge diode rectifiers for the secondary-side rectification (Figure 1a), while C block refers to the compensation network, which can be various types.
Because wireless power transfer is currently a matter of supplying power for a wide range of applications, the consideration about the power performance is important regarding proper selection of the optimal secondary-side rectifier topology.Figure 1b shows one possible alternative topology, while upper diodes of the bridge rectifier are replaced by the inductors without any common magnetic coupling.This configuration refers to the current-type rectifier, and its operational behavior is a matter of research within this paper.

Principle of Operation of Current-Type Rectifier
To explain the operational principle of the WPT system secondary-side current-type rectifier, assumption on the harmonic power supply is made initially (Figure 2), while only the fundamental 1st harmonic is considered.In this way, a certain error is concerned regarding the mathematical model, but this error is not exceptional to prove the operational performance analysis.We are more concerned with a qualitative explanation and not with a precise mathematical description at the beginning.In addition, it would be necessary to consider the specific V-A characteristic of a certain diode.The circuit schematic for the analysis is shown in Figure 3.

Analytical Expression for Optimal Design of Current-Doubler Inductors
A mathematical description of both operational intervals is provided in Equation ( 1).Using assumption according to the ideal coil of transmitter and receiver of the WPT system (RR1 = RR2 = 0) and considering that the voltage threshold of the diodes is uD1 = uD2 = 0, then Equation ( 1) can be transformed into a simpler form described by (2).Because both inductors are replacing diodes, the same electrical properties are considered for them.Due to the sinusoidal source voltage waveform u 1 of the power supply voltage, the operational cycle of the rectifier is divided into two symmetrical intervalsinterval A and interval B (Figure 3).

• INTERVAL A
This interval belongs to the time interval 0 < t < T/2.The supply voltage is positive, while current is flowing through inductor L R1 , parallel load C F R Z and through the diode D 2 , going back to the power supply.At the same time, inductor L R2 is supporting this current flow through the sourcing of the energy, which was absorbed during the previous operational cycle.

• INTERVAL B
This interval belongs to the time interval T/2 < t < T. The supply voltage has negative polarity, while current is flowing through inductor L R2 , parallel load C F R Z and through the diode D 1 , going back to the power supply.At the same time, inductor L R1 is supporting this current flow through the sourcing of the energy, which was absorbed during the previous operational cycle.

Analytical Expression for Optimal Design of Current-Doubler Inductors
A mathematical description of both operational intervals is provided in Equation ( 1).
Using assumption according to the ideal coil of transmitter and receiver of the WPT system (R R1 = R R2 = 0) and considering that the voltage threshold of the diodes is u D1 = u D2 = 0, then Equation ( 1) can be transformed into a simpler form described by (2).
Electronics 2023, 12, 4818 If L R1 = L R2 is valid, then from (2), it is possible to find out similarity regarding expressions for currents i R1 and i R2 .The difference reflected within the signs is related to the mutual phase shift, which is equal to 180 • .Exact expressions for time-dependent currents are gained through the integration of (2), while Equations ( 3) and ( 4) have the following form: By implementing the condition L R1 = L R2 = L R0 , Equations ( 5) and ( 6) are obtained: Because both i R1 and i R2 have periodic character, Equation ( 7) can be defined: Considering (7), it is possible to determine average values (8) of both investigated currents I R1 and I R2 : Equation ( 8) just confirms the above-mentioned assumption about the same waveforms of both currents except for their phase shift.Typical waveforms can be seen in Figure 4. Considering (7), it is possible to determine average values (8) of both investigated currents IR1 and IR2: Equation ( 8) just confirms the above-mentioned assumption about the same waveforms of both currents except for their phase shift.Typical waveforms can be seen in  At this point, the determination of the voltage and current ratio of the circuit will be determined, while the constant load voltage value is considered.Because of the current periodicity, the condition iR1(T) = iR1(0) is valid.Then, using (5), Equation ( 9) can be found: To find required relations, it is important to substitute iR1(T/2), while Equation ( 10) is then found as: At this point, the determination of the voltage and current ratio of the circuit will be determined, while the constant load voltage value is considered.Because of the current periodicity, the condition i R1 (T) = i R1 (0) is valid.Then, using (5), Equation (9) can be found: To find required relations, it is important to substitute i R1 (T/2), while Equation ( 10) is then found as: From ( 10), the unknown ratio can be found as follows: Taking into account the invariance of powers in the ideal power transfer case, i.e., U 1 I 1 = U Z I Z at a fully resonant state, the current ration can be directly described by ( 12) Now, the description is generally valid; nevertheless, in real applications, slightly no-resonant states are neglected with tolerable error.
For completeness, the value of i R1(0) would be determined, which is required for the calculation of all system currents.The procedure is made under the assumption that the load current is given by the instantaneous sum of the currents i R1(t) and i R2(t) .The formula is described by (13).
By solving (13), Equation ( 14) is found: The principle of the rectifier was explained in Figures 4 and 5 and through Equation ( 1).However, based on previous assumptions, Formula (15) can be defined.
Therefore, it can be seen that the current has the same shape (only with the opposite sign) in both the positive and negative half-waves of the input voltage.In this particular case, it is a quasi-rectangular waveform, which is based on the assumption of a sinusoidal power supply.Considering the connection of the rectifier to a WPT circuit with a current output, the current and voltage have a harmonic time dependency.For this reason, the logical step is to perform a harmonic decomposition of the relations defined by ( 14) using the Fourier transform and thereby obtain its fundamental harmonic (16).The parameters a 0 , a 1 and b 1 , used in (16), denote the Fourier coefficients.
RZ the substitution of ( 11) into (15), we obtain the formula for the total waveform of the input current (17).
The Fourier coefficients are determined by Equation ( 18): Then, the fundamental harmonic of the current is described by (19).
Current i 1 consists of two harmonic waves: the first one corresponds to the sine function, while the second one corresponds to the minus cosine function.Since the voltage u 1 varies according to the sine function, the first current component is in phase with the voltage, and the second one lags by 90 • .Regarding the theory of first-harmonic analysis, we can declare the second component as an imaginary part of the net current.
Recall that u 1 = U m sin(ωt) is valid; then, using Equation (20), it is possible to find out that two currents are phase shifted by 90 • , while the first of them has a pure ohmic character, whereby the second one has an imaginary character.
With respect to the supply voltage, the rectifier behaves like a load composed of parallel resistance and inductance.This inductance will negatively affect the power factor of the rectifier and must be dealt with.So, from Equation ( 20), we determine the imaginary component of impedance (21), which (among other things) shows the way of reflected L R0 onto the input terminals of the rectifier, i.e., the converted inductance L e .Its influence can be fully compensated by an additional capacitor C e (22) connected in parallel to the input terminals of the rectifier (see Figure 5).
This unity power factor ensures that both the input voltage and the drawn current are in phase.
The last step is to determine the inductance L R0 value.Equation (2) should be used as the initial condition, while in combination with Equation (11) and Equation (12), the consideration on the harmonic waveforms gives the formula for inductance (23).
Looking at (22) shows that the expression represents a simple relationship, but the design challenge is represented by the load vale dependency.Because of this relationship, the analyzed solution of the WPT system would be well suited for the systems with constant power requirements.

Comparison of WPT System Performance for Bridge Diode Rectifier and Proposed Circuit Modification
Experimental verification was provided for a quantitative comparison of the analyzed secondary-side rectifier alternative, while the most common compensation network for the transmitting and receiving side was used (series-series compensation) [27][28][29].The analyzed system is compared to the WPT system using a standard bridge-diode rectifier.The input to output parameters are listed in Table 1.U 1amp refers to the input voltage amplitude, U 2batt is the secondary-side voltage required by the load, f sw is the primary-side converter switching, P Z is the output power, k is the coupling coefficient and p is the ratio between the primary and secondary side.Table 2 indicates the values of the circuit parameters, while L 1 and L 2 are the values of inductances of the primary and secondary coil, C 1 and C 2 are the values of compensation capacitances, R 1 and R 2 are parasitic resistances of primary and secondary coils, and R Z is the value of the load resistance.In order to verify the electrical behavior of both alternatives, circuit simulation in the time domain was realized considering the operation reflecting the optimal value of the load.The simulation models are shown in Figure 6, while the primary-side inverter is represented by voltage-source replacement.In order to verify the electrical behavior of both alternatives, circuit simulation in the time domain was realized considering the operation reflecting the optimal value of the load.The simulation models are shown in Figure 6, while the primary-side inverter is represented by voltage-source replacement.Our main focus was concentrated on the time waveforms of the currents, which flow through individual legs of the rectifier (Ia, Ib), the load current, Iload, and the secondary-side voltage induced on the receiving coil U2. Figure 7a shows time waveforms of the mentioned circuit variables for the bridge-diode rectifier, while Figure 7b represents the situation for the current doubler rectifier.
Regarding the results of the WPT system with a bridge-diode rectifier, the currents Ia and Ib are forming the load current Iload.The secondary-side voltage has a rectangular shape corresponding to the operation of the voltage diode rectifier.Our main focus was concentrated on the time waveforms of the currents, which flow through individual legs of the rectifier (I a , I b ), the load current, I load , and the secondary-side voltage induced on the receiving coil U 2 .Figure 7a shows time waveforms of the mentioned circuit variables for the bridge-diode rectifier, while Figure 7b represents the situation for the current doubler rectifier.In order to verify the electrical behavior of both alternatives, circuit simulation in the time domain was realized considering the operation reflecting the optimal value of the load.The simulation models are shown in Figure 6, while the primary-side inverter is represented by voltage-source replacement.Our main focus was concentrated on the time waveforms of the currents, which flow through individual legs of the rectifier (Ia, Ib), the load current, Iload, and the secondary-side voltage induced on the receiving coil U2. Figure 7a shows time waveforms of the mentioned circuit variables for the bridge-diode rectifier, while Figure 7b represents the situation for the current doubler rectifier.
Regarding the results of the WPT system with a bridge-diode rectifier, the currents Ia and Ib are forming the load current Iload.The secondary-side voltage has a rectangular shape corresponding to the operation of the voltage diode rectifier.Regarding the results of the WPT system with a bridge-diode rectifier, the currents I a and I b are forming the load current I load .The secondary-side voltage has a rectangular shape corresponding to the operation of the voltage diode rectifier.
The waveforms of I a and I b of the current-doubler rectifier are mutually shifted by 90 • .I load is the sum of both of these leg currents.The ratio of the current ripple is affected by the value of inductors, while referring to the triangle shape of the currents reflects into a highly distorted shape of secondary-side voltage U 2 .This is valid also for the primary-side coil.During diode commutation, an extreme rise of the voltage is visible followed by its gradual decrease during the I load rise.After this transient period, the U 2 voltage is practically zero (Figure 8).By reduction in the value of inductance of the current-doubler rectifier, it is possible to reduce the maximum values of voltage U 2 .However, the efficiency and power transmission will be reduced as well.The waveforms of Ia and Ib of the current-doubler rectifier are mutually shifted by 90°.Iload is the sum of both of these leg currents.The ratio of the current ripple is affected by the value of inductors, while referring to the triangle shape of the currents reflects into a highly distorted shape of secondary-side voltage U2.This is valid also for the primary-side coil.During diode commutation, an extreme rise of the voltage is visible followed by its gradual decrease during the Iload rise.After this transient period, the U2 voltage is practically zero (Figure 8).By reduction in the value of inductance of the current-doubler rectifier, it is possible to reduce the maximum values of voltage U2.However, the efficiency and power transmission will be reduced as well.

Experimental Verification
Figure 9a shows the block diagram of system setup during experimental verifications, while Figure 9b shows the physical prototype with laboratory equipment of the analyzed WPT system.A more detailed design regarding the practical realization of the secondary-side rectifier is shown in Figure 10.It is seen that the upper bridge rectifier diodes are replaced by the inductors, while the values are determined using Equation (22).Consequently, the sizing of the inductor conductor refers to the secondary-side current value.

Experimental Verification
Figure 9a shows the block diagram of the system setup during experimental verifications, while Figure 9b shows the physical prototype with laboratory equipment of the analyzed WPT system.The waveforms of Ia and Ib of the current-doubler rectifier are mutually shifted by 90°.Iload is the sum of both of these leg currents.The ratio of the current ripple is affected by the value of inductors, while referring to the triangle shape of the currents reflects into a highly distorted shape of secondary-side voltage U2.This is valid also for the primary-side coil.During diode commutation, an extreme rise of the voltage is visible followed by its gradual decrease during the Iload rise.After this transient period, the U2 voltage is practically zero (Figure 8).By reduction in the value of inductance of the current-doubler rectifier, it is possible to reduce the maximum values of voltage U2.However, the efficiency and power transmission will be reduced as well.

Experimental Verification
Figure 9a shows the block diagram of the system setup during experimental verifications, while Figure 9b shows the physical prototype with laboratory equipment of the analyzed WPT system.A more detailed design regarding the practical realization of the secondary-side rectifier is shown in Figure 10.It is seen that the upper bridge rectifier diodes are replaced by the inductors, while the values are determined using Equation (22).Consequently, the sizing of the inductor conductor refers to the secondary-side current value.A more detailed design regarding the practical realization of the secondary-side rectifier is shown in Figure 10.It is seen that the upper bridge rectifier diodes are replaced by the inductors, while the values are determined using Equation (22).Consequently, the sizing of the inductor conductor refers to the secondary-side current value.The initial experimental verification of the system operation was performed in the form of the analysis of the time waveforms of primary and secondary-side electrical variables.Figure 11 (left) is showing these results for the operation at the optimal value of the load, and Figure 11 (right) shows the operation in a real battery charging application.The measured waveforms in Figure 11 correspond to the simulation results (Figures 7 and 8) in terms of values and shapes.Consequently, to perform comparative analysis of the system performance considering various types of the secondary-side rectification, certain modifications regarding system parameters should be performed.With the same supply voltage, the alternative rectifier with a current doubler will deliver much higher power compared to the default system ("A").There are at least three ways to deal with this.We will mark them with the letters "B", "C" and "D".

•
Option "B" assumes the preservation of the circuit parameters, and therefore, it is necessary to reduce the supply voltage to the value (23) with the help of (11).The initial experimental verification of the system operation was performed in the form of the analysis of the time waveforms of primary and secondary-side electrical variables.Figure 11 (left) is showing these results for the operation at the optimal value of the load, and Figure 11 (right) shows the operation in a real battery charging application.The measured waveforms in Figure 11 correspond to the simulation results (Figures 7 and 8) in terms of values and shapes.The initial experimental verification of the system operation was performed in the form of the analysis of the time waveforms of primary and secondary-side electrical variables.Figure 11 (left) is showing these results for the operation at the optimal value of the load, and Figure 11 (right) shows the operation in a real battery charging application.The measured waveforms in Figure 11 correspond to the simulation results (Figures 7 and 8) in terms of values and shapes.Consequently, to perform comparative analysis of the system performance considering various types of the secondary-side rectification, certain modifications regarding system parameters should be performed.With the same supply voltage, the alternative rectifier with a current doubler will deliver much higher power compared to the default system ("A").There are at least three ways to deal with this.We will mark them with the letters "B", "C" and "D".

•
Option "B" assumes the preservation of the circuit parameters, and therefore, it is necessary to reduce the supply voltage to the value (23) with the help of (11).Consequently, to perform comparative analysis of the system performance considering various types of the secondary-side rectification, certain modifications regarding system parameters should be performed.With the same supply voltage, the alternative rectifier with a current doubler will deliver much higher power compared to the default system ("A").There are at least three ways to deal with this.We will mark them with the letters "B", "C" and "D".

•
Option "B" assumes the preservation of the circuit parameters, and therefore, it is necessary to reduce the supply voltage to the value (23) with the help of (11).

•
Option "C" considers the same supply voltage as option "A", and therefore, a modification of the secondary circuit is necessary.Considering (13), it is enough to recalculate the secondary inductance according to (23).

•
Option "D" is a completely new system design with an equivalent load determined by Equation ( 23).

•
The results of all variants are compared in Table 3, where ∆P j1 and ∆P j2 denote the winding losses on the primary and secondary side.

•
As can be seen from the results, option "B" comes out as the worst one.The reason is the lower voltage compared to other options and thus the higher losses due to the higher current flowing on the primary side.However, the transfer of the losses from the secondary side to the primary side is favorable here, which can play a significant role in the case of a waterproof design of the charger.Option "D" comes out in terms of overall efficiency like opt."A", but its lower THDi (due to the type of the used rectifier) leads to lower apparent power.This has a favorable effect regarding power losses in the primary winding and brings an indisputable advantage from a thermal management point of view.Option "C" is characterized with the best efficiency of all the investigated variations.

•
Because the operation of the WPT system is not fixed for one defined value of the load, the sensitivity analysis of options "A" and "C" was performed regarding the load variations.This approach is a key factor, which would determine the selection of the proper topology for WPT charger design.

•
From the results (Table 4), it is seen that opt."A" achieved the maximum efficiency for the 2R Z value, and a constant efficiency decline rate can be observed above the 2Rz operating point.The reason why opt."A" has achieved the maximum efficiency for different state instead of the nominal, lies in fact that the equivalent load does not have enough value according to (23).
Therefore, one of the alternative rectifier topology advantages may consist within the condition (24) for easier fulfillment.

Discussion
The experiments agreement with the simulations, which is shown above in Section 4. alongside a summary of the experimental results.Graphical representation of the experimental results is given in Figure 12 for Table 3 and in Figure 13 for Table 4, showing satisfactory results.
At the beginning, the proposed alternative I-type rectifier consists of only two diodes and two high-quality inductors without mutual coupling, so the lower rectifier power losses are expected as well.This phenomenon is certified by Figure 12, which captures the system efficiency in the optimal load case.Therefore, but not because of that, the proposed solution is advantageous.
Next, according to the construction, the proposed solution is cheaper and smaller than that of a standard diode rectifier and especially than active impedance-matching circuits and, in some cases, than alternative passive impedance matching of the wireless power transfer load.
Finally, the proposed solution shows better properties in real application conditions, too. Figure 13 shows the system efficiency under real conditions-it means under different load values especially.
The proposed solution can increase the system efficiency with low costs, small space and small complications.

Discussion
The experiments agreement with the simulations, which is shown above in Section 4. alongside a summary of the experimental results.Graphical representation of the experimental results is given in Figure 12 for Table 3 and in Figure 13 for Table 4, showing satisfactory results.
At the beginning, the proposed alternative I-type rectifier consists of only two diodes and two high-quality inductors without mutual coupling, so the lower rectifier power losses are expected as well.This phenomenon is certified by Figure 12, which captures the system efficiency in the optimal load case.Therefore, but not because of that, the proposed solution is advantageous.
Next, according to the construction, the proposed solution is cheaper and smaller than that of a standard diode rectifier and especially than active impedance-matching circuits and, in some cases, than alternative passive impedance matching of the wireless power transfer load.
Finally, the proposed solution shows better properties in real application conditions, too. Figure 13 shows the system efficiency under real conditions-it means under different load values especially.
The proposed solution can increase the system efficiency with low costs, small space and small complications.

Conclusions
This paper provides a system analysis of the wireless power transfer system equipped with an alternative secondary-side rectifier solution.The proposed solution represents a proper choice for the applications where low equivalent load is presented.An analytical approach was performed in order to find the optimal value of the secondaryside current-doubler inductances-in order to meet the highest possible efficiency for defined operational condition.Several relationships have been discussed during the analysis, thus enabling electrical engineers to understand the design process of certain WPT systems with an alternative topology of the secondary-side rectifier.The experimental verification of the operational performance was realized under laboratory conditions, while the proposed solution was adequately adapted to meet the required input-output parameters of commonly used systems equipped by a standard bridge-voltage rectifier.Mutual comparison from an efficiency point of view is given by laboratory verification-the achieved results show that the presented alternative improves the operational efficiency for nominal parameters by 3.73% (bridge rectifier-92.27%,current-doubler rectifier-96%).A second experiment was performed in the way of load variation sensitivity analysis, whereby the proposed solution exhibits higher efficiency in comparison to the standard solution within the whole operational range.Based on these facts, it is worth saying that for the case of the specific application purpose (low equivalent loads) of the WPT system, the presented solution represents an attractive alternative that is not complex.The future works will be more focused on the EMI performance evaluation of the proposed alternative solution of the secondary-side rectifier of the WPT system.The reasons for this are that from natural operation, it was seen (Figures 7 and 8) that the voltage stress is much higher compared to the standard solutions of the rectifiers.Therefore, the relation between circuit components values (current-doubler inductors) and the possibilities for voltage stress reduction will be performed in greater detail.
Author Contributions: V.K.: investigation, writing-original draft preparation, project administration, methodology, M.Z.: investigation, validation, M.T.: investigation, validation, J.S.: investigation, validation, M.F.: methodology, investigation, writing-review and editing, funding acquisition.All authors have read and agreed to the published version of the manuscript.

Conclusions
This paper provides a system analysis of the wireless power transfer system equipped with an alternative secondary-side rectifier solution.The proposed solution represents a proper choice for the applications where low equivalent load is presented.An analytical approach was performed in order to find the optimal value of the secondary-side current-doubler inductances-in order to meet the highest possible efficiency for defined operational condition.Several relationships have been discussed during the analysis, thus enabling electrical engineers to understand the design process of certain WPT systems with an alternative topology of the secondary-side rectifier.The experimental verification of the operational performance was realized under laboratory conditions, while the proposed solution was adequately adapted to meet the required input-output parameters of commonly used systems equipped by a standard bridge-voltage rectifier.Mutual comparison from an efficiency point of view is given by laboratory verification-the achieved results show that the presented alternative improves the operational efficiency for nominal parameters by 3.73% (bridge rectifier-92.27%,current-doubler rectifier-96%).A second experiment was performed in the way of load variation sensitivity analysis, whereby the proposed solution exhibits higher efficiency in comparison to the standard solution within the whole operational range.Based on these facts, it is worth saying that for the case of the specific application purpose (low equivalent loads) of the WPT system, the presented solution represents an attractive alternative that is not complex.The future works will be more focused on the EMI performance evaluation of the proposed alternative solution of the secondary-side rectifier of the WPT system.The reasons for this are that from natural operation, it was seen (Figures 7 and 8) that the voltage stress is much higher compared to the standard solutions of the rectifiers.Therefore, the relation between circuit components values (current-doubler inductors) and the possibilities for voltage stress reduction will be performed in greater detail.

Figure 1 .
Figure 1.Equivalent schematics of WPT system with standard secondary-side bridge diode rectifier (a).Equivalent schematics of WPT system with modified secondary-side diode rectifier (b).

Figure 2 .
Figure 2. Current-type rectifier with harmonic power supply.

Figure 1 .
Figure 1.Equivalent schematics of WPT system with standard secondary-side bridge diode rectifier (a).Equivalent schematics of WPT system with modified secondary-side diode rectifier (b).

Figure 1 .
Figure 1.Equivalent schematics of WPT system with standard secondary-side bridge diode rectifier (a).Equivalent schematics of WPT system with modified secondary-side diode rectifier (b).

Figure 2 .
Figure 2. Current-type rectifier with harmonic power supply.Figure 2. Current-type rectifier with harmonic power supply.

Figure 2 .
Figure 2. Current-type rectifier with harmonic power supply.Figure 2. Current-type rectifier with harmonic power supply.

Figure 3 .
Figure 3. Operation during time Interval A (a). Equivalent operation during time Interval B (b).

Figure 3 .
Figure 3. Operation during time Interval A (a). Equivalent operation during time Interval B (b).

Figure 4 .
Figure 4. Typical time waveforms of rectifier with current doubler.

Figure 4 .
Figure 4. Typical time waveforms of rectifier with current doubler.

Figure 5 .
Figure 5. Operation during time Interval A including compensation network (a).Equivalent operation during time Interval B including compensation network (b).

Figure 6 .
Figure 6. Circuit diagram of simulation model for WPT system with bridge-diode rectifier (a) and proposed alternative (b).

Figure 7 .
Figure 7. Time waveforms of selected electrical variables for bridge-diode rectifier (a) and time waveforms of selected electrical variables for current-doubler rectifier (b).

Figure 6 .
Figure 6. Circuit diagram of simulation model for WPT system with bridge-diode rectifier (a) and proposed alternative (b).

Figure 6 .
Figure 6. Circuit diagram of simulation model for WPT system with bridge-diode rectifier (a) and proposed alternative (b).

Figure 7 .
Figure 7. Time waveforms of selected electrical variables for bridge-diode rectifier (a) and time waveforms of selected electrical variables for current-doubler rectifier (b).

Figure 7 .
Figure 7. Time waveforms of selected electrical variables for bridge-diode rectifier (a) and time waveforms of selected electrical variables for current-doubler rectifier (b).

Figure 8 .
Figure 8.Time waveform of selected electrical variables for current-doubler rectifier.

Figure 9 .
Figure 9. Block diagram of the experimental system setup (a) and physical system setup for testing (b).

Figure 8 .
Figure 8.Time waveform of selected electrical variables for current-doubler rectifier.

Figure 8 .
Figure 8.Time waveform of selected electrical variables for current-doubler rectifier.

Figure 9 .
Figure 9. Block diagram of the experimental system setup (a) and physical system setup for testing (b).

Figure 9 .
Figure 9. Block diagram of the experimental system setup (a) and physical system setup for testing (b).

Figure 10 .
Figure 10.Physical prototype of current-doubler rectifier for investigated WPT system.

Figure 11 .
Figure 11.Time waveforms of WPT system with current-doubler rectifier: left for the ideal configuration; right for the real battery charging application (blue-primary current, light blue-primary voltage, left purple-secondary current, right purple-one DC leg current, green-secondary voltage).

Figure 10 .
Figure 10.Physical prototype of current-doubler rectifier for investigated WPT system.

Figure 10 .
Figure 10.Physical prototype of current-doubler rectifier for investigated WPT system.

Figure 11 .
Figure 11.Time waveforms of WPT system with current-doubler rectifier: left for the ideal configuration; right for the real battery charging application (blue-primary current, light blue-primary voltage, left purple-secondary current, right purple-one DC leg current, green-secondary voltage).

Figure 11 .
Figure 11.Time waveforms of WPT system with current-doubler rectifier: left for the ideal configuration; right for the real battery charging application (blue-primary current, light blue-primary voltage, left purple-secondary current, right purple-one DC leg current, green-secondary voltage).

Figure 12 .
Figure 12.The results of the operational performance of analyzed WPT system-all options in optimal system state.

Figure 12 .
Figure 12.The results of the operational performance of analyzed WPT system-all options in optimal system state.

Figure 13 .
Figure 13.The results of the operational performance of analyzed WPT system-option A and option C under variable load values.

Figure 13 .
Figure 13.The results of the operational performance of analyzed WPT system-option A and option C under variable load values.

Table 1 .
Input to output nominal parameters of experimental test.

Table 2 .
Values of the circuit components of investigated WPT system.

Table 2 .
Values of the circuit components of investigated WPT system.

Table 2 .
Values of the circuit components of investigated WPT system.

Table 3 .
The results of the operational performance of analyzed WPT system.

Table 4 .
The results of the operational performance of analyzed WPT system.

Table 4 .
The results of the operational performance of analyzed WPT system.