A New Detection Method for Load Side Broken Conductor Fault Based on Negative to Positive Current Sequence

: Faults in distribution overhead lines occur due to various reasons, such as rain, strong winds, lightning, and other natural causes. The protection from the load side broken conductor (LSBC) faults has been one of the biggest challenges in the power distribution network. The small current generated by the LSBC fault makes the traditional protection system unable to detect this type of fault. The danger of LSBC fault is still enormous; besides, the available works of literature addressing this issue face difﬁculties when applying it to the real power system. This paper proposes a new method for detecting LSBC fault using single-ended measurements to the overhead distribution lines. The detection method is based on the constant ratio of negative to positive sequence current measured at the feeder end. The proposed study is performed using MATLAB software to implement a real network as a case study and veriﬁed by mathematical analysis. According to obtained results, we demonstrated that the fault in the electrical network had been detected with 100% of feeder protection. The proposed method has the beneﬁt of being applicable and compatible with the existing measurement equipment, even when used in conjunction with overcurrent and earth fault relay in the electrical substation. Therefore, the negative to positive sequence currents are powerful in aiding fault detection. The beneﬁt of this approach is providing a suitable LSBC protection solution for utilities while also opening new prospects in fault detection techniques in the distribution system.


Introduction
The main reasons for power supply disturbances in distribution overhead lines are series, shunt, and series shunt faults. In both utility and public safety, fault detection is a crucial concern. Earth or ground fault protection is an essential defence in electrical systems; it is necessary to preserve electrical networks and equipment. A broken conductor fault (BCF) occurs when an overhead line is interrupted and may or may not contact the ground, depending on the event's severity. The broken conductor on the source side with high impedance fault, broken conductor on the load side with any impedance fault, or an open circuit with a conductor not touching the ground might all be responsible for the problem of undetected fault as illustrated and classified in Figure 1. The most common and dangerous type of BCF occurs when an exciting mainline drops and contacts the earth. This condition is exceptionally harmful since there is a danger of electric shock to people and a fire risk. As a result, detecting BCF is essential from human health and performance efficiency standpoints. Protective relays and circuit breakers are major components of the large interconnected power system. Substations in power distribution systems involve numerous pre-programmed protection relays with multiple stages to protect the system from many types of faults. Nevertheless, it is well known that current protection technology misses (30-50)% of BCF failures. This may lead to critical and dangerous situations that threaten the lives of citizens and animals and reduce the lifetime of the utility equipment. A broken conductor represents an open phase state on the electrical circuit in a medium voltage distribution radial system. As shown in Figure 2, BCF might be one of the following causes: (1) Open line where conductor does not touch the ground from two terminals.
(2) Source side of the broken conductor with high ground resistance. (3) Load side broken conductor with any ground resistance. The load side broken conductor (LSBC) fault is a specific type of earth fault (single line to ground), which is challenging to detect since the conductor might remain suspended from the overhead line's source-side while touching the ground from the load side. The sparks of LSBC fault create a small fault current that does not reach the pickup value of the earth fault relay, so the protection relay will not be triggered, and the medium voltage (MV) feeder remains in the CLOSE position [1]. Therefore, the LSBC faults are usually undetectable by traditional over current and earth fault protection relays as well as no response of any activated protection relay. Explaining the substation feeder setting and the pickup values of protection relays is needed to analyze the practical problem in the protection of MV distribution feeders. The ground fault is set to 10% of the overcurrent setting; this is a minimum ratio to sense the low earth fault current. When the earth fault setting value decreases, interference will occur, such as the leakage current results from the load unbalance.
Electronics 2022, 11, x FOR PEER REVIEW 2 of 13 protection technology misses (30-50)% of BCF failures. This may lead to critical and dangerous situations that threaten the lives of citizens and animals and reduce the lifetime of the utility equipment. A broken conductor represents an open phase state on the electrical circuit in a medium voltage distribution radial system. As shown in Figure 2, BCF might be one of the following causes: (1) Open line where conductor does not touch the ground from two terminals. (2) Source side of the broken conductor with high ground resistance.
(3) Load side broken conductor with any ground resistance. The load side broken conductor (LSBC) fault is a specific type of earth fault (single line to ground), which is challenging to detect since the conductor might remain suspended from the overhead line's sourceside while touching the ground from the load side. The sparks of LSBC fault create a small fault current that does not reach the pickup value of the earth fault relay, so the protection relay will not be triggered, and the medium voltage (MV) feeder remains in the CLOSE position [1]. Therefore, the LSBC faults are usually undetectable by traditional over current and earth fault protection relays as well as no response of any activated protection relay. Explaining the substation feeder setting and the pickup values of protection relays is needed to analyze the practical problem in the protection of MV distribution feeders. The ground fault is set to 10% of the overcurrent setting; this is a minimum ratio to sense the low earth fault current. When the earth fault setting value decreases, interference will occur, such as the leakage current results from the load unbalance.  Many studies have been done to enhance and detect the faults [2], where the detection technique example of open circuits and downed conductors shows: (1) A loss of phase-detection at pole-mounted switchgear. (2) Detection of blown high voltage (HV) fuses. (3) Using under-voltage detection at transformer poles. Reference [3] offers asymmetric current methodology considering a relationship between the negative sequence and zero with the positive sequence during a BCF event.
According to [4], it is possible to locate a BCF using only the magnitudes of current and voltage phasors of a single terminal utilizing the group data handling technique. The inputs and outputs of the interpolation function are the faulty phase's current and voltage, respectively, and the precise position of the fault. A method for early identification of faults in power lines by analyzing the symmetrical voltage components in real-time has been developed [5]. A new approach has been developed in [6] to detect underground cable faults in radial distribution networks. The algorithm uses a radial line's end-measured phase-to-phase voltages as input signals. In [7], the study proposes an protection technology misses (30-50)% of BCF failures. This may lead to critical and dangerous situations that threaten the lives of citizens and animals and reduce the lifetime of the utility equipment. A broken conductor represents an open phase state on the electrical circuit in a medium voltage distribution radial system. As shown in Figure 2, BCF might be one of the following causes: (1) Open line where conductor does not touch the ground from two terminals. (2) Source side of the broken conductor with high ground resistance.
(3) Load side broken conductor with any ground resistance. The load side broken conductor (LSBC) fault is a specific type of earth fault (single line to ground), which is challenging to detect since the conductor might remain suspended from the overhead line's sourceside while touching the ground from the load side. The sparks of LSBC fault create a small fault current that does not reach the pickup value of the earth fault relay, so the protection relay will not be triggered, and the medium voltage (MV) feeder remains in the CLOSE position [1]. Therefore, the LSBC faults are usually undetectable by traditional over current and earth fault protection relays as well as no response of any activated protection relay. Explaining the substation feeder setting and the pickup values of protection relays is needed to analyze the practical problem in the protection of MV distribution feeders. The ground fault is set to 10% of the overcurrent setting; this is a minimum ratio to sense the low earth fault current. When the earth fault setting value decreases, interference will occur, such as the leakage current results from the load unbalance.   [3] offers asymmetric current methodology considering a relationship between the negative sequence and zero with the positive sequence during a BCF event.
According to [4], it is possible to locate a BCF using only the magnitudes of current and voltage phasors of a single terminal utilizing the group data handling technique. The inputs and outputs of the interpolation function are the faulty phase's current and voltage, respectively, and the precise position of the fault. A method for early identification of faults in power lines by analyzing the symmetrical voltage components in real-time has been developed [5]. A new approach has been developed in [6] to detect underground cable faults in radial distribution networks. The algorithm uses a radial line's end-measured phase-to-phase voltages as input signals. In [7], the study proposes an (3) Using under-voltage detection at transformer poles. Reference [3] offers asymmetric current methodology considering a relationship between the negative sequence and zero with the positive sequence during a BCF event.
According to [4], it is possible to locate a BCF using only the magnitudes of current and voltage phasors of a single terminal utilizing the group data handling technique. The inputs and outputs of the interpolation function are the faulty phase's current and voltage, respectively, and the precise position of the fault. A method for early identification of faults in power lines by analyzing the symmetrical voltage components in real-time has been developed [5]. A new approach has been developed in [6] to detect underground cable faults in radial distribution networks. The algorithm uses a radial line's end-measured phase-to-phase voltages as input signals. In [7], the study proposes an implementation of asymmetrical component logic that enhances traditional protection methods using a singlephase transformer. The authors in [8] present an approach based on the zero-sequence current's decreasing periodic components to locate a high impedance ground faulty line section. When a single-phase high impedance fault (HIF) occurs in a resonant grounding system, it examines the parallel resonance process. A unique integrated approach has been proposed to detect and locate open conductor faults in HV transmission systems [9]. Decomposition of local current signals is performed utilizing a discrete wavelet transform with a single-level corruption in the proposed scheme unit.
Accordingly, studying and analyzing LSBC fault is very important and requires identifying some concepts. In this paper, the proposed method solves the detection of LSBC fault depending on the relationship between the negative and positive current sequence during LSBC fault. The paper presents a new applicable study based on asymmetric current methodology as I 2 /I 1 during an LSBC fault. The other existing diagnosis methods are currently inapplicable to the existing traditional protection system, as discussed in Section 4. The contributions of this research paper are: • Analyze the distribution system under faults.

•
A new applicable method is proposed to detect LSBC faults.
The remainder of this paper is organized as follows: Section 2 introduces the methodology, which describes the proposed methods and introduces the mathematical analysis. Section 3 describes the case study of real distribution network. Section 4 presents the results and discusses them. Section 5 concludes the paper.

Fault Incidents
The low voltage supply network experiences abnormal voltage in two or three phases. It occurs when a broken conductor or disconnected phase causes an open-circuit fault, such as blown HV fuses in an 11 kV radially fed overhead line. This has a significant impact on the supply of electricity to customers. Such problems are often reported by customers who suffer abnormal energy supply or loss of power because of substation-based current detection techniques' inability to identify them. Short-circuit faults can be detected using phase overcurrent and earth fault relays. Phase overcurrent and earth faults can be detected with (inverse definite minimum time) or (definite time lag) protection.
It is impossible to start an overcurrent or earth fault if an open circuit causes it. Fault impedance can be exceedingly high when a downed conductor comes into touch with highly resistant substances, such as asphalt, sand, or boulders. Back-feed earth fault current may not be detectable by overcurrent or earth fault in the distribution power transformer in the case of a downed conductor on the load side of a fault point, as shown in Figure 3. implementation of asymmetrical component logic that enhances traditional protection methods using a single-phase transformer. The authors in [8] present an approach based on the zero-sequence current's decreasing periodic components to locate a high impedance ground faulty line section. When a single-phase high impedance fault (HIF) occurs in a resonant grounding system, it examines the parallel resonance process. A unique integrated approach has been proposed to detect and locate open conductor faults in HV transmission systems [9]. Decomposition of local current signals is performed utilizing a discrete wavelet transform with a single-level corruption in the proposed scheme unit. Accordingly, studying and analyzing LSBC fault is very important and requires identifying some concepts. In this paper, the proposed method solves the detection of LSBC fault depending on the relationship between the negative and positive current sequence during LSBC fault. The paper presents a new applicable study based on asymmetric current methodology as I2/I1 during an LSBC fault. The other existing diagnosis methods are currently inapplicable to the existing traditional protection system, as discussed in Section 4. The contributions of this research paper are: • Analyze the distribution system under faults.

•
A new applicable method is proposed to detect LSBC faults.
The remainder of this paper is organized as follows: Section 2 introduces the methodology, which describes the proposed methods and introduces the mathematical analysis. Section 3 describes the case study of real distribution network. Section 4 presents the results and discusses them. Section 5 concludes the paper.

Fault Incidents
The low voltage supply network experiences abnormal voltage in two or three phases. It occurs when a broken conductor or disconnected phase causes an open-circuit fault, such as blown HV fuses in an 11 kV radially fed overhead line. This has a significant impact on the supply of electricity to customers. Such problems are often reported by customers who suffer abnormal energy supply or loss of power because of substation-based current detection techniques' inability to identify them. Short-circuit faults can be detected using phase overcurrent and earth fault relays. Phase overcurrent and earth faults can be detected with (inverse definite minimum time) or (definite time lag) protection.
It is impossible to start an overcurrent or earth fault if an open circuit causes it. Fault impedance can be exceedingly high when a downed conductor comes into touch with highly resistant substances, such as asphalt, sand, or boulders. Back-feed earth fault current may not be detectable by overcurrent or earth fault in the distribution power transformer in the case of a downed conductor on the load side of a fault point, as shown in Figure 3.

Mathematical Analysis of LSBC Fault
It is possible to represent the unbalanced power system using the phase diagram; the phase representation is by applying analytical processes. The purpose is to dismantle this unbalanced system into balanced systems, each with phases equal to the number of phases of the original unbalanced system. These balanced systems are then called symmetric compounds. Although this analytical method includes multi-phase systems, the conversation will be limited to three-phase systems. The technique is being applied to obtain identical compounds by analyzing the three unbalanced phases of the threephase power system into three systems, each of which is three-phase and balanced. These groups of balanced compounds are: (1) Compounds of the positive relay; these consist of three phases of equal size, shifted from each other by an angle of 120, and have the same sequence of phases as the original system. (2) Compounds of the negative relay consist of three phases of equal magnitude, shifted from each other by an angle of 120, but the phase sequence here is opposite to that of the original system. (3) Compounds of the zero sequence, which consist of three phases, equal in phases, and identical in direction (that is, the value of the displacement angle between the three phases is equal to zero), so it was called the zero-sequence components [10]. Figure 4 shows the representation of symmetrical components.

Mathematical Analysis of LSBC Fault
It is possible to represent the unbalanced power system using the phase diagram; the phase representation is by applying analytical processes. The purpose is to dismantle this unbalanced system into balanced systems, each with phases equal to the number of phases of the original unbalanced system. These balanced systems are then called symmetric compounds. Although this analytical method includes multi-phase systems, the conversation will be limited to three-phase systems. The technique is being applied to obtain identical compounds by analyzing the three unbalanced phases of the three-phase power system into three systems, each of which is three-phase and balanced. These groups of balanced compounds are: (1) Compounds of the positive relay; these consist of three phases of equal size, shifted from each other by an angle of 120, and have the same sequence of phases as the original system. (2) Compounds of the negative relay consist of three phases of equal magnitude, shifted from each other by an angle of 120, but the phase sequence here is opposite to that of the original system. (3) Compounds of the zero sequence, which consist of three phases, equal in phases, and identical in direction (that is, the value of the displacement angle between the three phases is equal to zero), so it was called the zero-sequence components [10]. Figure 4 shows the representation of symmetrical components.  As depicted in Figure 5, the LSBC concept is illustrated by a line that connects a supply-side to the load. The symmetric components transformation (SCT) can analyze LSBC faults, which is extensively applicable. Pseudo phasor algebra is applied to a sinusoidal situation using the SCT. A series impedance ZS represents the broken conductor to create a generic theory [11]. As shown in Figure 6, the shunt impedance Zg also accounts for the conductor-to-ground contact.   As depicted in Figure 5, the LSBC concept is illustrated by a line that connects a supplyside to the load. The symmetric components transformation (SCT) can analyze LSBC faults, which is extensively applicable. Pseudo phasor algebra is applied to a sinusoidal situation using the SCT. A series impedance ZS represents the broken conductor to create a generic theory [11]. As shown in Figure 6, the shunt impedance Zg also accounts for the conductorto-ground contact.

Mathematical Analysis of LSBC Fault
It is possible to represent the unbalanced power system using the phase diagram; the phase representation is by applying analytical processes. The purpose is to dismantle this unbalanced system into balanced systems, each with phases equal to the number of phases of the original unbalanced system. These balanced systems are then called symmetric compounds. Although this analytical method includes multi-phase systems, the conversation will be limited to three-phase systems. The technique is being applied to obtain identical compounds by analyzing the three unbalanced phases of the three-phase power system into three systems, each of which is three-phase and balanced. These groups of balanced compounds are: (1) Compounds of the positive relay; these consist of three phases of equal size, shifted from each other by an angle of 120, and have the same sequence of phases as the original system. (2) Compounds of the negative relay consist of three phases of equal magnitude, shifted from each other by an angle of 120, but the phase sequence here is opposite to that of the original system. (3) Compounds of the zero sequence, which consist of three phases, equal in phases, and identical in direction (that is, the value of the displacement angle between the three phases is equal to zero), so it was called the zero-sequence components [10]. Figure 4 shows the representation of symmetrical components.  As depicted in Figure 5, the LSBC concept is illustrated by a line that connects a supply-side to the load. The symmetric components transformation (SCT) can analyze LSBC faults, which is extensively applicable. Pseudo phasor algebra is applied to a sinusoidal situation using the SCT. A series impedance ZS represents the broken conductor to create a generic theory [11]. As shown in Figure 6, the shunt impedance Zg also accounts for the conductor-to-ground contact.   When the total conductor interruption occurs, the series impedance tends to infinity (i.e., ZS → ∞) while the conductor to ground solid contact leads follow Zg → 0. The LSBC fault study is performed by applying the SCT to the G and H sections, as shown in Figure  4 The subscripts 0, 1, and 2 indicate the zero, positive, and negative sequence components, respectively, where a = 1 ∠ 120 °, a 2 = 1 ∠ 240 °. Equation (1) can be rewritten as Equation (2) Applying Kirchhoff's current law, the following expression in Equation (4) for the fault section can be written.  When the total conductor interruption occurs, the series impedance tends to infinity (i.e., Z S → ∞) while the conductor to ground solid contact leads follow Zg → 0. The LSBC fault study is performed by applying the SCT to the G and H sections, as shown in Figure 4, where: I a , I b , I c , V a , V b , V c are phase currents and phase voltages before the fault section. I a , I b ,I c , V a , V b , V c are phase currents and phase voltages after the fault section.
The line currents with symmetrical components in section G are given in Equation (1).
In addition, section H, is rewritten as Equation (3).
Applying Kirchhoff's current law, the following expression in Equation (4) for the fault section can be written.    Combining (1), (3), and (4), the final formula is obtained as in Equation (5).

Proposed Methodology
The protection engineer must understand the negative phase sequence (NPS) principle and apply the necessary settings based on different fault situations when using NPS protection on each given feeder [12]. However, the values of I 2 can be sensitive to real load adjustments due to practical limitations in constructing balanced networks, where NPS protection is an excellent phase imbalance detector. Positive phase sequence (PPS) has traditionally been related to feeder loads and frequently indicates customer service quality. Overload of customer usage (or commonly asymmetrical three-phase fault) suggests that a line has too much PPS flowing over it and that the current should be terminated to maintain the benefit [13].
The day load variations in utility supply may indicate higher NPS, although this does not necessarily mean a conductor discontinuity. However, when one or more of the lines are broken, typical overcurrent/earth fault relays may fail to detect the output since the PPS does not necessarily increase. NPS protection is usually set at 30% of the overcurrent configuration. Therefore, it is safe to assume that a broken conductor will not be recognized if it is applied to feeders. When the load current is less than 10A, a broken conductor can be identified with a high degree of certainty. This phenomenon is more widespread at lower loads. For certain risks related to the failure of protection equipment, only NPS overcurrent protection can provide backup protection to solidly grounded Delta-Wye transformers [14]. Sequence components are present for a range of conditions, not only this type of faults as the open pole, load and line unbalance, breaker pole scatters, and current transformer ratio errors and saturation [15].
Thus, the NPS to PPS ratio |I 2 /I 1 | should be compared, rather than each protective factor. This helps reduce the instability in NPS numbers across the range of energy distribution to customers while also detecting an open phase discontinuity. Figure 7 depicts the proposed procedure's flow chart. Figure 8 show the proposed methodology of this paper.

Case Study and Simulation Analysis
In this section, we consider the theoretical discussion. The implementation of a real network as a case study is presented. The Al-Abasia distribution substation located in the middle Euphrates region in Najaf governorate serves a large area of mixed residential, commercial, and agriculture loads and is taken as the study network. The secondary power station consists of twelve feeders, whereas the F10 feeder consists of 15 overhead transformers with a rated line to line voltage of 11 kV. The simulated circuit of the singleline diagram is presented in Figure 9. The screenshot of the MATLAB Simulink is given in Figure 10. The specification and parameters applied to this study are given in Table 1. The load of 11 distribution transformers is balanced and distributed as in Table 2.

Case Study and Simulation Analysis
In this section, we consider the theoretical discussion. The implementation of a real network as a case study is presented. The Al-Abasia distribution substation located in the middle Euphrates region in Najaf governorate serves a large area of mixed residential, commercial, and agriculture loads and is taken as the study network. The secondary power station consists of twelve feeders, whereas the F10 feeder consists of 15 overhead transformers with a rated line to line voltage of 11 kV. The simulated circuit of the singleline diagram is presented in Figure 9. The screenshot of the MATLAB Simulink is given in Figure 10. The specification and parameters applied to this study are given in Table 1. The load of 11 distribution transformers is balanced and distributed as in Table 2.      MATLAB software and its associated Simulink toolboxes are used to test the proposed methodology. The simulation program is performed 15 times for the load side broken conductor faults in the feeder, as shown in Figure 9. The measurements were taken at the 33/11 kV substation and the end of the feeder for fifteen cases of LSBC fault. The faults start from the beginning of the feeder, and the results are given in Table 3. It is noted that the fault current in the LSBC fault phase increases from zero up to a value that becomes approximately equal to the other two phases. It causes the percentage level between the faulted and the other two phases to change between 100% and 13%.

Mathematical Results
In the mathematical analysis, Equation (5) was used to determine the ground current (I g ) from the sequence currents (I 0 ) measured by the Simulink program in the substation when the fault occurs in phase C. Using Equation (6), the mathematical results were written in Table 4.   In Table 4, we noted that there is an equal absolute value of the ground current resulting from the fault in the two cases of taking measurements using the MATLAB program and the results through mathematical analysis as shown in Equation (7).
The results showed that the values of the phase shift to I g between the mathematical and MATLAB results are approximately 180 • for all fifteen cases of fault sites. The same results are formed using the other measurements to sequence currents I 1 and I 2 by Equations (8) and (9).

Unbalance Phases Current Results
When the location of the fault is at the starting feeder, the measured values of the unfaulted lines' currents are 86 A to 76 A. At the same time, the faulted line current in phase C is equal to zero. This is due to the presence of the LSBC fault, which is the main problem of this research paper. The protective devices are not sensitive to this type of fault due to the decrease in the values of the three-phase fault currents, unlike other types of power system faults in the Figure 1, in which the importance of the fault currents is high. When the position of the LSBC fault is far from the substation, an increase in the current values occurs in the faulty phase C until the threshold value is reached. The threshold value is the significance that determines the change in the percentage value of the unbalance currents to be 10%. The permissible percentage in the distribution networks is less than 10%. If it exceeds this value, it is considered a fault detection which the protection devices must protect the lines. In this case, 100% of the 11 kV feeder cannot be protected through unbalanced protection. Increasing the loads to more than loads of the case study in this research paper will inevitably decrease the unbalanced current table's percentage 1 to less than 10%. To calculate the percentage ratio of the unbalance three-phase currents, we apply Equation (10) where I max is the maximum current of three-phase currents during the LSBC faults. I min is the minimum current of three-phase currents during the LSBC faults [16].

Neutral Fault Current Results
The results showed in Table 3 that the earth fault protection in a substation cannot detect neutral current because it was less than the permissible value 30 A in the case study (Al-Abasia substations). The current values through which the neutral protection operates vary from (30 to 150) amperes, where the earth fault current (High) is determined by Equation (11), and the earth fault current (Low) is determined by Equation (12).
The current value limits in Equations (10) and (11) apply when the current transformer is 300/5, the range allowed in Iraqi substations. In Table 3, the current levels in neutral varied between (7-29) A in the fifteen cases of LSBC fault, indicating that the protection devices are not responsive to the fault. Due to decreasing the loads, the longer the distance between the fault and the substation, the less current flows. The currents resulting from the fault in the neutral are the best possible state since the HIF is not taken, resulting from the conductor's contact with more insulating materials like grass, sand, soil, and others. The problem will be increased because the fault current is not detected.

Negative to Positive Sequence Percentage Current Ratio Results
The ratio |I 2 /I 1 | was measured at two sites, first at the substation and the second at the feeder's end. It was observed that the ratio at the substation varied between (7-79%). In comparison, it is fixed at 50% at the feeder's end, as shown in Figure 11. The relay setting of |I 2 /I 1 | should be less than 20% [17]. In other words, the relay does not operate by less than 20%. The ratio of |I 2 /I 1 | is (7-18%) measured at the substation side for the fault site number (11)(12)(13)(14)(15). So, it cannot be relied upon to detect the LSBC fault, which leads us to propose another way to measure |I 2 /I 1 | at the feeder end. It is noted that the ratio of currents |I 2 /I 1 | is proven to be 50% at the end of the feeder. This ratio is for all 15 cases of faults, which is the best solution to solve the research problem. In the absence of a discontinuity, the |I 2 /I 1 | ratio is nearly constant for any variation in load demand on three phases. When a discontinuity emerges on one or more lines, the |I 2 /I 1 | ratio climbs above 20%, which is evident in a healthy line with |I 2 /I 1 | close to zero. Impedance calculations are not necessary because the positive and negative sequence impedances are identical for most residential loads, as may be concluded by looking at the ratio between I 2 and I 1 . A comparison between the proposed method with recent literature is given in Table 5.

Conclusions
The electrical faults in the power system lead to a significant risk for public safety such as people, animals, crops, and forests. The LSBC fault is a specific type of fault that happens on the overhead line, which occurs on the load side since the faulted line is still Figure 11. Negative to positive sequence percentage current ratio. Table 5. Comparison between the proposed method with recent literature.

The Proposed Method
The Available Literature Methods

•
One measurement unit is needed at the feeder end.
• The relays are needed in each bus of the grid [3]. • Requires a voltage sensor to be placed at each end of the MV branch [5].
• Detection does not depend on transformer connection (delta-star) or (star-delta).
• Some drawbacks are mainly related to the delta transforms placed [3].
• No need for collecting system historical data.
• Need for collecting historical system data [4].
• Detection the faults in ungrounded and overhead lines.
• Detect the faults when using single-phase and three-phase transformers.
• Mainly detects the fault in a scenario with single-phase transformers [7].
• No complicated communication is needed.
• Feeder terminal units that are needed to install along the feeder with advanced communication links lead to additional hardware and software complexity [8].
• Applicable with the traditional overcurrent and earth fault protection.

Conclusions
The electrical faults in the power system lead to a significant risk for public safety such as people, animals, crops, and forests. The LSBC fault is a specific type of fault that happens on the overhead line, which occurs on the load side since the faulted line is still energized via back-feed from the distribution transformer. This type of fault has an entirely different effect on current feeders than the traditional line-to-ground fault. For the low neutral current of LSBC fault, the earth fault protection relay does not reach the pickup value, so it cannot detect the fault. This paper presented the performance analysis based on feeder current's NPS to PPS ratio |I 2 /I 1 |. The proposed approach is applied to a real distribution feeder in Iraq that was simulated with the MATLAB platform. The results were compared with the mathematical analysis and other related works. It was observed that the proposed |I 2 /I 1 | at the substation side protects 67% of the feeder, while the proposed |I 2 /I 1 | at the feeder end protects 100% of the feeder from LSBC fault. This paper holds several advantages compared to the previous research. Firstly, the fault is detected accurately without using distributed measurements. Secondly, the proposed method has high sensitivity on fault detection without depending on noise, power swing, transformer saturation, or harmonics. Thirdly, this method provided good analysis and found an applicable solution for the distribution utilities, which was previously missing in the literature of this field. The method can also be implemented to any other three-phase three-wire distribution feeder to get the same benefits.
For future work, we will consider analyzing other types of networks in the presence of distributed generation and evaluating the speed response of the relay. Additionally, we will study the suitable techniques for transmitting the command from the feeder end to the substation.
Author Contributions: Among those involved in the study's conception and execution were the authors A.G.A.-B., M.K.A. and F.M.F.F., as well as its analysis and paper writing. All authors have read and agreed to the published version of the manuscript.