Theoretical and Empirical Veriﬁcation of Electrical Impedance Matching Method for High-Power Transducers

: In our prior study, a systematic approach was used to devise Langevin transducers for high-power applications where the energy efﬁciency was not considered in the design criteria. In this paper, the impedance matching methods are thus proposed to evaluate what matching topology is appropriate for their use. Both the series inductor scheme and low pass ﬁlter composed of a series inductor and shunt capacitor are examined as matching circuits. According to MATLAB simulation, the resonance frequency is seen at 36.79 kHz due to a series L circuit, and its associated impedance is reduced by 70.45% from that of its non-matching condition. The measured resonance frequency is 36.77 kHz and the corresponding impedance is decreased by 59.52%. Furthermore, the acoustic pressure is measured to determine the effect of the matching circuit on the transducer’s actual behavior. The transducer with a series L circuit shows more efﬁcient matching results, 2.28 kPa of positive acoustic pressure is emitted without matching and 3.35 kPa is emitted with a series L element, respectively. As a result, this study demonstrates how to evaluate the inﬂuence of matching circuits by using our customized approach rather than commercial SPICE programs, as well as how to experimentally verify the acoustic behavior of high-power Langevin transducers.


Introduction
Bolt-clamped transducers, also known as Langevin type transducers, are high-power ultrasonic devices that have been developed for a variety of applications including ultrasonic welders [1,2] and sonochemical mixing processors [3,4]. Such instruments have widely been used because ultrasonic energy from those transducers is safe and powerful enough to provide desirable results. In particular, ultrasonic scalpel and scaling tools have commonly been exploited for medical purposes, e.g., removal of mineral deposits in teeth [5], soft tissue incision [6], and blood vessel sealing [7]. Acoustophoretic energy irradiated from transducers is converted into either mechanical or thermal energy to prompt physical or chemical reactions on those samples. Typical Langevin transducers are composed of a compression bolt, piezoelectric element, tail mass, front mass, and metal horn. A theoretical design method of those transducers used for therapeutic treatment was proposed in our previous work [8], in which the transducer was designed to achieve a specific resonance frequency by combining Mason's model with an equivalent circuit analysis. More recently, a designed transducer was produced to investigate the effect of bolt-tightening force on its resonance characteristics [9].
In generating sufficient acoustic powers for the thermal ablation of soft tissue, Langevin transducers have conventionally been excited with continuous sinusoidal waves of finite voltage amplitude. Under this circumstance, electrical impedance mismatch between transducers and peripheral equipment frequently creates excessive heat elevation that decreases the transducer's resonance frequency and ultimately causes the device's failure [10,11]. In order to ease the overheating problem arising from the mismatch, the use of heat-resistant layers, porous transducer housing, and filling the housing cavity with insulation materials was proposed [12], which provides only temporary remedies. The impedance match is still a more fundamental issue in improving the various functional performances of transducers, particularly power transfer and imaging resolution. Electrical impedance mismatch between transducers and peripheral equipment adversely affects the power conversion from excitation pulsers by reflecting too much energy from those sources, in turn, degrading the transducer's efficiency [13]. For the enhancement of axial resolution in diagnostic imaging scanners, received echoes from targets need to carry broad bandwidth signals of high sensitivity. Due to energy loss in the transducer's components along with media attenuation [14], poor mismatch makes the imaging depth much shallower than it is supposed to be. In high frequency imaging for ophthalmology and dermatology, this becomes even worse by significantly missing the content at certain frequencies [15].
In this regard, several impedance matching approaches for ultrasonic transducers have been developed in longitudinal mode. In order to turn an inductive Langevin transducer into a resistive load, for example, a capacitive output impedance driver was designed to operate them at anti-resonance by optimizing the transducer's driving frequency for loss reduction [16]. For sandwiched transducers, the Smith chart was employed to compensate their reactance and to finally accomplish the resistance tuning. Typically, their input impedance was moved to a point near 50 Ω at the center of the chart by adding a proper series or parallel reactive elements [17]. However, much attention has been paid to impedance characterization with little emphasis on the acoustic pressure measurement, while concrete transducer structures are not explicitly presented. Moreover, commercial SPICE programs are mainly used to quantify the effect of impedance matching on transducer performance.
In order to overcome these drawbacks, in this paper, two types of matching schemes, e.g., series L circuits and LC low pass networks, are examined along with their corresponding transducer configuration as follows.

•
Parameters of their circuit components corresponding to each matching circuit are derived based on experimental values probed by the impedance analyzer.

•
To verify the electromechanical characteristics of the matched transducer, our equivalent circuit model is combined with proposed matching circuits. • A hydrophone system is built to measure the acoustic pressure emitted from impedancematched transducers for each matching scheme. • Mechanical quality factor, Q m , is computed to evaluate the energy efficiency of the transducer. • Both simulated and experimental results are compared to demonstrate the capability of our method to quantitatively design appropriate transducers for power generation.
Therefore, both electrical and acoustical behaviors influenced by the matching circuits are reported here to justify our approach for the power enhancement of bolt-clamped transducers.

Equivalent Circuit Models
There are various types of impedance matching methods for ultrasonic transducers, such as the combination of shunt/series inductors [18], series capacitors [19], parallel damping resistances [20], and LC filters [21]. These methods are closely associated with equivalent circuits of transducers for describing complex characteristics of piezoelectric elements where Mason [22], Krimholtz-Leedom-Matthaei (KLM) [23], and Butterworth-Van Dyke (BVD) models [24] are preferred to explain their electromechanical behaviors. In particular, the BVD model has often been referred to represent a transducer with RLC parameters at resonance frequency, f r . Since our Langevin transducer investigated in this study has a single f r at low-frequency range, both BVD and Mason models are used to calculate those lumped elements and to estimate the resonance properties of the transducer over the same frequency range. As shown in Figure 1a, the BVD model is composed of a Electronics 2022, 11,194 3 of 13 mechanical arm with a resistor R s , an inductor L s , a capacitor C s in series, and an electrical arm with a parallel capacitor C 0 . 2022, 10, x FOR PEER REVIEW 3 of 14 parameters at resonance frequency, fr. Since our Langevin transducer investigated in this study has a single fr at low-frequency range, both BVD and Mason models are used to calculate those lumped elements and to estimate the resonance properties of the transducer over the same frequency range. As shown in Figure 1a, the BVD model is composed of a mechanical arm with a resistor Rs, an inductor Ls, a capacitor Cs in series, and an electrical arm with a parallel capacitor C0.   In addition, the Mason model consists of an ideal transformer, two capacitors, and three equivalent impedances, as depicted in Figure 1b. Each impedance is calculated by Equations (3) and (4) [25].
ZA is the radiation impedance determined by the product of Z0 and the area of the piezoelectric element, where Z0 is the acoustic impedance. kp is the wavenumber equal to angular frequency w divided by the sound speed in the element. The turn ratio n of the transformer in the model is determined by Equation (5), where d33 and 33 E s are the piezoelectric charge coefficient in thickness mode and the elastic compliance, respectively [26].  (1) [21].
C 0 is an equivalent clamped capacitance of the transducer as expressed by Equation (2) [8].
n 0 is the number of the piezoelectric element, ε 33 , S, k t , and L are the permittivity, surface area, electromechanical coupling coefficient, and the length of the element, respectively. According to the datasheet of C-203 material from FUJI ceramics, C 0 is 17.47 nF (n 0 : 4, S: 28.59 mm 2 , L: 5 mm).
In addition, the Mason model consists of an ideal transformer, two capacitors, and three equivalent impedances, as depicted in Figure 1b. Each impedance is calculated by Equations (3) and (4) [25].
Z A is the radiation impedance determined by the product of Z 0 and the area of the piezoelectric element, where Z 0 is the acoustic impedance. k p is the wavenumber equal to angular frequency w divided by the sound speed in the element. The turn ratio n of the transformer in the model is determined by Equation (5), where d 33 and s E 33 are the piezoelectric charge coefficient in thickness mode and the elastic compliance, respectively [26].
These types of representations are limited to describing the acoustic response, and yet they are still useful for elucidating the impedance characteristics of the transducer. T-shaped equivalent circuit for modeling other passive parts of the transducer is employed to calculate the transducer's electrical property as presented in [8]. Finally, the impedance matching circuit developed here is paired with this Mason's electrical port.

Matching Circuits
Both series inductor and LC filter circuit with series inductance and shunt capacitor are chosen among several matching networks to explore their effect on characteristics of highpower transducers due to their simple structure, cost-effectiveness, and widespread use. Circuit element values for those matching topologies are determined by impedance analyzer (Agilent, 4294A, Santa Clara, CA 95051, USA). The matching procedure is illustrated in Figure 2.
matching circuit developed here is paired with this Mason's electrical port.

Matching Circuits
Both series inductor and LC filter circuit with series inductance and shunt capa are chosen among several matching networks to explore their effect on characteristi high-power transducers due to their simple structure, cost-effectiveness, and widesp use. Circuit element values for those matching topologies are determined by imped analyzer (Agilent, 4294A, Santa Clara, CA 95051, USA). The matching procedure is i trated in Figure 2.

Series L Circuit
The inductance for series L matching circuit is derived by the reactance of the tr ducer. At fr, the impedance of the transducer modelled by BVD circuit is capacitive du the parallel capacitance C0 [27]. To compensate the capacitive reactance generated by clamped capacitance, a series inductor is added. The total impedance Z of the transd in BVD model is then derived by Equation (6). The series RS, LS, CS, and parallel C combined to compute the total impedance [19].

Series L Circuit
The inductance for series L matching circuit is derived by the reactance of the transducer. At f r , the impedance of the transducer modelled by BVD circuit is capacitive due to the parallel capacitance C 0 [27]. To compensate the capacitive reactance generated by the clamped capacitance, a series inductor is added. The total impedance Z of the transducer in BVD model is then derived by Equation (6). The series R S , L S , C S , and parallel C 0 are combined to compute the total impedance [19].
R TR and X TR are the resistance and reactance components, respectively, of Z at angular frequency ω. Matching conditions for maximum acoustic output and optimal series inductance L S are then represented in Equations (7) and (8).
A complete circuit consisting of the transducer, the series inductor, and the excitation source is shown in Figure 3. Note that the output impedance of the source is assumed to be purely resistive R ex . A complete circuit consisting of the transducer, the series inductor, and the excitation source is shown in Figure 3. Note that the output impedance of the source is assumed to be purely resistive Rex.

LC Circuit
By simplifying the BVD model at fr, the transducer can be replaced as RS in parallel with C0. This simplified model can be considered as a load seen from the excitation circuit. According to transmission line theory, L-section matching networks are utilized to guarantee the maximum power transfer for this type of circuit [28,29]. This matching topology is the simplest lumped matching method as it consists of only two lumped components.

LC Circuit
By simplifying the BVD model at f r , the transducer can be replaced as R S in parallel with C 0 . This simplified model can be considered as a load seen from the excitation circuit. According to transmission line theory, L-section matching networks are utilized to guarantee the maximum power transfer for this type of circuit [28,29]. This matching topology is the simplest lumped matching method as it consists of only two lumped components. As the measured value of R S is higher than the impedance of the excitation circuit, 50 Ω, LC network as a matching circuit is preferred [30]. The designed matching circuit is shown to be a low pass filter configuration, as shown in Figure 4. For the sake of simplicity, the original clamped capacitance will be included in final step.
Electronics 2022, 10, x FOR PEER REVIEW 6 of 14 As the measured value of RS is higher than the impedance of the excitation circuit, 50 Ω, LC network as a matching circuit is preferred [30]. The designed matching circuit is shown to be a low pass filter configuration, as shown in Figure 4. For the sake of simplicity, the original clamped capacitance will be included in final step. The electrical input impedance is determined by Equation (9).
In matching condition, the transducer seen from the source can be considered as a purely resistive element by cancelling out its reactive component of Zin. Thus, Rex and Xs are defined by putting the opposite sign to the imaginary part of Zin as Equations (10) and (11). The electrical input impedance is determined by Equation (9).
Electronics 2022, 11, 194 6 of 13 In matching condition, the transducer seen from the source can be considered as a purely resistive element by cancelling out its reactive component of Z in . Thus, R ex and X s are defined by putting the opposite sign to the imaginary part of Z in as Equations (10) and (11).
The relations between each parameter can be derived as Equations (12) and (13).
The parameter Q of the whole circuit is only validated under R ex < R S condition. Consequently, the inductance of the series inductor and the capacitance of the shunt capacitor are determined by Equations (14) and (15), respectively.
Note that the clamped capacitance of the transducer should be included in calculation of Equation (15).
The cross-sectional view of our transducer is shown in Figure 5a, where 1 is a central bolt, 2 a tail mass, 3 a piezoelectric layer, 4 ~6 a front mass including an exponential horn, and Consequently, the inductance of the series inductor and the capacitance of the shunt capacitor are determined by Equations (14) and (15), respectively.
Note that the clamped capacitance of the transducer should be included in calculation of Equation (15).
The cross-sectional view of our transducer is shown in Figure 5a, where ① is a central bolt, ② a tail mass, ③ a piezoelectric layer, ④~⑥ a front mass including an exponential horn, and ⑦~⑩ an attachable rod numbered from left to right. The central bolt plays a crucial role in not only clamping components but also maintaining the piezoelectric compression mode during operation. The corresponding equivalent circuit is employed to estimate the effect of matching circuit on the transducer characteristics via MATLAB simulation. Then, we compute the numerical data, including fr, anti-resonance frequency fa, minimum and maximum impedances, and mechanical quality factor Qm according to Equation (16). In particular, Qm describes the mechanical performance of the transducer such as mechanical loss or efficiency [31]. It is, thus, crucial to prevent the loss by accomplishing high Qm with little energy leakage. In surface acoustic wave (SAW) resonators, it was shown that their sensitivities can be improved by selecting proper electrode materials such as copper, silver, and tungsten to obtain higher Qm [32]. Several approaches including external feedback control [33] and thermal-piezoresistive pumping [34] have also been developed for micro-electromechanical resonators to modify their Qm by providing them with external time-varying or static energy sources. an attachable rod numbered from left to right. The central bolt plays a crucial role in not only clamping components but also maintaining the piezoelectric compression mode during operation. The corresponding equivalent circuit is employed to estimate the effect of matching circuit on the transducer characteristics via MATLAB simulation. Then, we compute the numerical data, including f r , anti-resonance frequency f a , minimum and maximum impedances, and mechanical quality factor Q m according to Equation (16). In particular, Q m describes the mechanical performance of the transducer such as mechanical loss or efficiency [31]. It is, thus, crucial to prevent the loss by accomplishing high Q m with little energy leakage. In surface acoustic wave (SAW) resonators, it was shown that their sensitivities can be improved by selecting proper electrode materials such as copper, silver, and tungsten to obtain higher Q m [32]. Several approaches including external feedback control [33] and thermal-piezoresistive pumping [34] have also been developed for micro-electromechanical resonators to modify their Q m by providing them with external time-varying or static energy sources.
In Figure 5b,c, complete equivalent circuits including our matching models are represented to estimate the frequency response of the impedance.

Experimental Setup
Pressure measurement system in Figure 6a Figure 6b. The pressure is measured by the sensor with a resolution of 10 µV/Pa and the recorded signal is shown by the oscilloscope. The time interval between each data point is set to 10 µs for data acquisition and the number of data are 1002. To protect matching circuit elements in Figure 6c, the voltage amplitude first starts with lowest level and is then gradually increased from 50 V pp to 100 V pp with 10 V pp apart. transducer such as mechanical loss or efficiency [31]. It is, thus, crucial to prevent the loss by accomplishing high Qm with little energy leakage. In surface acoustic wave (SAW) resonators, it was shown that their sensitivities can be improved by selecting proper electrode materials such as copper, silver, and tungsten to obtain higher Qm [32]. Several approaches including external feedback control [33] and thermal-piezoresistive pumping [34] have also been developed for micro-electromechanical resonators to modify their Qm by providing them with external time-varying or static energy sources.  In Figure 5b,c, complete equivalent circuits including our matching models are represented to estimate the frequency response of the impedance.

Experimental Setup
Pressure measurement system in Figure 6a is composed of a hydrophone sensor (8103, Bruel & Kjaer, Naerum, Denmark), a pre-amplifier (2692-A-0S1, Bruel & Kjaer, Naerum, Denmark), an oscilloscope (DS-5652, IWATSU, Kugayama, Japan), and a water tank with motorized stage. The distance between the hydrophone and the transducer tip is 1 mm in Figure 6b. The pressure is measured by the sensor with a resolution of 10 μV/Pa and the recorded signal is shown by the oscilloscope. The time interval between each data point is set to 10 μs for data acquisition and the number of data are 1002. To protect matching circuit elements in Figure 6c, the voltage amplitude first starts with lowest level and is then gradually increased from 50 Vpp to 100 Vpp with 10 Vpp apart.

Results and Discussion
Numerical values of the BVD model corresponding to our fabricated transducer were investigated with the impedance analyzer. The measured results of Rs, CS, LS, and C0 were

Results and Discussion
Numerical values of the BVD model corresponding to our fabricated transducer were investigated with the impedance analyzer. The measured results of R s , C S , L S , and C 0 were 71.39 Ω, 69.87 pF, 268.55 mH, and 16.20 nF, respectively. There was an error in C 0 between the calculated and measured value is 1.26 nF. This can readily be understood since the electrodes located between the piezoelectric elements have finite thickness and thus undesirable parasitic capacitance may exist [35]. As a result, the measured capacitance is less than that of our theoretical model. In fact, such interelectrode capacitance can be reduced with thin electrode coating by taking advantage of ultra-small sized particles, e.g., nano-Ag pastes [36,37]. Figure 7 represents the BVD model together with the measured values. fr with the minimum impedance value of 131.36 Ω was 36.82 kHz, close to the value calculated with Equation (1), 36.87 kHz. Therefore, the measured numerical parameters are considered to be reasonable. According to Equation (6), the resultant reactance of the transducer was 244.62 Ω for the series L matching circuit and, in turn, the necessary inductance derived from Equation (8) was 1.2 mH. In the case of the LC matching scheme, the series inductance and shunt capacitance were obtained from Equations (14) and (15), 0.13 mH and 22 nF, respectively. Using these components, we connected each matching circuit to the transducer and analyzed the electrical input impedance through a frequency sweep. Both simulation and experimental results are compared in Figure 8. Under non-matching conditions, the simulation results in Figure 8a showed that fr and fa were found at 37.31 kHz and 38.20 kHz, with corresponding impedances of 23.59 Ω and 13.7 kΩ. According to Equation (16)  f r with the minimum impedance value of 131.36 Ω was 36.82 kHz, close to the value calculated with Equation (1), 36.87 kHz. Therefore, the measured numerical parameters are considered to be reasonable. According to Equation (6), the resultant reactance of the transducer was 244.62 Ω for the series L matching circuit and, in turn, the necessary inductance derived from Equation (8) was 1.2 mH. In the case of the LC matching scheme, the series inductance and shunt capacitance were obtained from Equations (14) and (15), 0.13 mH and 22 nF, respectively. Using these components, we connected each matching circuit to the transducer and analyzed the electrical input impedance through a frequency sweep. Both simulation and experimental results are compared in Figure 8. fr with the minimum impedance value of 131.36 Ω was 36.82 kHz, close to the value calculated with Equation (1), 36.87 kHz. Therefore, the measured numerical parameters are considered to be reasonable. According to Equation (6), the resultant reactance of the transducer was 244.62 Ω for the series L matching circuit and, in turn, the necessary inductance derived from Equation (8) was 1.2 mH. In the case of the LC matching scheme, the series inductance and shunt capacitance were obtained from Equations (14) and (15), 0.13 mH and 22 nF, respectively. Using these components, we connected each matching circuit to the transducer and analyzed the electrical input impedance through a frequency sweep. Both simulation and experimental results are compared in Figure 8. Under non-matching conditions, the simulation results in Figure 8a showed that fr and fa were found at 37.31 kHz and 38.20 kHz, with corresponding impedances of 23.59 Ω and 13.7 kΩ. According to Equation (16), the corresponding Qm was 217.27. Similarly, the Under non-matching conditions, the simulation results in Figure 8a showed that f r and f a were found at 37.31 kHz and 38.20 kHz, with corresponding impedances of 23.59 Ω and 13.7 kΩ. According to Equation (16), the corresponding Q m was 217.27. Similarly, the matching effect on the transducer was further simulated for the LC circuit and series L matching cases. f r , f a , impedances, and Q m for the LC topology were 37.26 kHz, 38.20 kHz, 20.67 Ω, 13.7 kΩ, and 234.51, respectively, whereas they were 36.79 kHz, 38.20 kHz, 6.97 Ω, 13.7 kΩ, and 461.66, respectively, for the series L matching. Meanwhile, the impedance spectrum acquired from the impedance analyzer is plotted in Figure 8b. When the LC network was applied, the measured f r and f a were the same as their non-matching values of 36.82 kHz and 37.16 kHz, respectively, whereas the series L matching results indicated that each frequency was 36.77 kHz and 37.01 kHz, respectively. In addition, the minimum impedance was reduced from 131.36 Ω to 120.25 Ω, and 53.17 Ω in each matching circuit. The resultant Q m was 111.95, 122.30, and 394.79. In earlier studies, various materials were electroplated for SAW resonators to enhance Q m . For example, Q m was 1.4 × 10 4 at 1.9 GHz with silver electrode, while it was 5.5 × 10 3 at 925 MHz with tungsten [32]. For cantilevers of atomic force microscopy (AFM), it varied from 3.5 × 10 4 to 2 × 10 5 at 75 kHz through 300 kHz [38]. In comparison with our results, a much higher Q m was exhibited for their applications, particularly in SAW devices at a range of hundreds of MHz to GHz. Furthermore, a spurious resonance, also called parasitic resonance, was observed in the absence of matching, and LC network conditions were drastically reduced when the series inductor was connected. The above results are summarized in Tables 1 and 2. In the MATLAB simulation, the LC network and the series L element decreased the impedance at f r by 12.38% and 70.45%, respectively. The estimated Q m value was increased by 17.24 and 244.39, respectively, when compared to the non-matching case. Similarly, experimental results showed that the minimum impedance was reduced by 8.46% and 59.52%, respectively. The computed Q m was also improved by 10.34 and 282.38, respectively. Since many variables affecting the input electrical impedance are neglected in our equivalent circuit model, e.g., electrode thickness, complex piezoelectric properties, and shear vibration of long rods, the discrepancy in the impedance may exist between the simulation and test. Although there are mismatches in precise impedance magnitudes, the effect of each matching condition on the numerical results is similar in both tables. Typically, the series L topology is more efficient in electrical matching, demonstrating higher Q m than that of the LC matching. Since the stacked-piezoelectric layer is shown as the capacitive device, a pure inductive component can be employed to compensate for its capacitive characteristics. Moreover, the LC filter topology preferred for use in broadband transducers may not be suitable for high-power emitting transducers because its spectral components are likely to lose a considerable amount of energy over a wide frequency range. Hence, the use of a series L matching circuit is reasonable for high-power transducers at a range of tens of kHz. It is worth noting that it is possible to characterize impedance-matched power transducers via our analytical model, rather than commercial SPICE programs.
In order to evaluate the matching effect on acoustic behavior, the pressure from the transducer was measured with the hydrophone sensor immersed in a water tank. Voltage amplitudes of received signals were transferred to a PC and subsequently converted to their corresponding pressure via calibration data provided by the sensor manufacturer. Table 3 shows that the voltage gains of L matching are steadily greater than those of LC matching during the test. The measured pressure under 100 V pp excitation is depicted in Figure 9. The maximum positive pressure is 3.35 kPa with the series L matching while the minimum positive value is 2.41 kPa in both LC topology and non-matching condition. In each case, the absolute values of negative pressure are detected as 3.21 kPa, 2.28 kPa, and 1.96 kPa, respectively. The peak-to-peak pressures are 6.46 kPa, 4.69 kPa, and 4.24 kPa, respectively, proportional to the acquired Q m .   The pressure depending on the driving voltage is given in Figure 10. Both ma negative and positive pressures are consistently greater in the series L matchi those in other conditions, as seen in Figure 10a,b, which can be expected from the gain results. Except for 70 Vpp and 80 Vpp, the peak-to-peak pressure for the LC slightly higher than that for the unmatched condition, as shown in Figure 10c. T sults clearly indicate that the impedance matching improves the acoustic perform the transducer. The pressure depending on the driving voltage is given in Figure 10. Both maximum negative and positive pressures are consistently greater in the series L matching than those in other conditions, as seen in Figure 10a,b, which can be expected from the voltage gain results. Except for 70 V pp and 80 V pp , the peak-to-peak pressure for the LC case is slightly higher than that for the unmatched condition, as shown in Figure 10c. These results clearly indicate that the impedance matching improves the acoustic performance of the transducer. those in other conditions, as seen in Figure 10a,b, which can be expected from the gain results. Except for 70 Vpp and 80 Vpp, the peak-to-peak pressure for the LC slightly higher than that for the unmatched condition, as shown in Figure 10c. T sults clearly indicate that the impedance matching improves the acoustic perform the transducer.

Conclusions
We investigated impedance matching networks to improve the efficiency of hi power Langevin transducers. Among various types of equivalent circuits, the BVD a the Mason models were employed to calculate their lumped circuit elements and to e mate the resonance characteristics. As matching circuits, a series inductor circuit and pass LC configuration were chosen. By using an impedance analyzer, the necessary co ponents for series L and LC circuits were determined and added to our theoretical mo of the fabricated transducer. Subsequently, the measured impedance of the transdu combined with the matching circuit was investigated in comparison with that of the s ulation results. According to both simulation and experimental data, the series L match network was found to be more suitable for impedance matching, leading to an increas Qm. It is demonstrated that our equivalent circuit corresponding to the transducer can useful with the matching network to characterize the impedance over a range of ten kHz. Through the hydrophone system, the effect of the matching condition on the act acoustic pressure in water was evaluated. The transducer with a series L circuit show the most efficient matching results. Despite the slight increment in Qm, the LC scheme a represented an improved peak-to-peak pressure as compared to that of the unmatc

Conclusions
We investigated impedance matching networks to improve the efficiency of highpower Langevin transducers. Among various types of equivalent circuits, the BVD and the Mason models were employed to calculate their lumped circuit elements and to estimate the resonance characteristics. As matching circuits, a series inductor circuit and low pass LC configuration were chosen. By using an impedance analyzer, the necessary components for series L and LC circuits were determined and added to our theoretical model of the fabricated transducer. Subsequently, the measured impedance of the transducer combined with the matching circuit was investigated in comparison with that of the simulation results. According to both simulation and experimental data, the series L matching network was found to be more suitable for impedance matching, leading to an increase in Q m . It is demonstrated that our equivalent circuit corresponding to the transducer can be useful with the matching network to characterize the impedance over a range of tens of kHz. Through the hydrophone system, the effect of the matching condition on the actual acoustic pressure in water was evaluated. The transducer with a series L circuit showed the most efficient matching results. Despite the slight increment in Q m , the LC scheme also represented an improved peak-to-peak pressure as compared to that of the unmatched condition. For future works, other impedance matching techniques can be explored further by considering the cable effect on the transducer performance based on transmission line theory [39] and a transformer [40], or by taking advantage of piezocomposite ceramics with modified clamped dielectric permittivity via volume ratio change [41].

Conflicts of Interest:
The authors declare no conflict of interest.