Power Quality Enhancement in Electric Arc Furnace Using Matrix Converter and Static VAR Compensator

In recent years, non-linear loads on the distribution side are increasing rapidly. Notably, the electric arc furnace (EAF) is the most used non-linear load due to its diverse applications for industrial needs. However, EAF has some disadvantages like uneven distribution of heat inside the furnace, release of unwanted gases, increased level of harmonics, and Flickers in voltages. Specifically, power quality concerns are more and need comprehensive solutions. In this work, a matrix converter (MC) along with static VAR compensator (SVC) is proposed, and the hybrid exponential-hyperbolic furnace model is adapted in MATLAB platform. Simulations are carried out for different cases and the observed results are compared with existing methodologies. It was perceived that the power quality parameters such as peak current and voltages, total harmonic distortions (THDs), voltage flickers, and power factors are enhanced compared with existing methodologies. Precisely, the THD of current and voltage attains a prime rate of about 2.85% and 29.54%, respectively. Moreover, the proposed model’s voltage flicker and power factor offer a grander scale of about 1.26% and 0.9975, respectively. The enhanced scheme provides more significant advantages to the large-scale steel manufacturing plant with EAF.


Introduction
Nowadays, the usage of steel in the modern world is increasing rapidly due to the higher demand rate. It is used in various fields such as construction, infrastructure, transportation, medical, and weapons. Notably, around 52% of the steel is used for building and infrastructure purposes, and the remaining in other sectors like domestic appliances, mechanical equipment, electrical appliances, etc. The steel production was around 189 million tons in the 1950s, and it increased to 1869 million tons in 2019. Among the countries, China produces approximately 1000 million tonnages of steel every year and stands first in steel production. Secondly, India has around 120 million tonnages every year [1]. The increasing usage of steel is achieved only by the mass production of small EAF. SiC and MG-Si were mainly used in many electronic applications and solar power generation applications. This work used Raman spectroscopy to analyze the SiC and the entire mechanical parts were produced, assembled, and tested using LabVIEW NI environment.
Likewise, the artificial neural network was adopted to model EAFs [2] and arc-length computation. Specifically, this system found the arc length in stable and unstable conditions. The furnace efficiency and productivity were improved using the ANN-based electric arc furnace. Further, Rahmatollah Hooshmand et al. [18] discussed a new time-domain model for EAF. The performance of EAF was analyzed using three models, namely hyperbolic model, complete exponential model, and the proposed exponential-hyperbolic model. The proposed exponential, hyperbolic model offered an excellent approximation without initial conditions of EAF. The voltage-current characteristics and total harmonic distortion (THD) were derived with good approximation. Moreover, Philippe Ladoux et al. [19] performed a comparison between ac and dc converters for the electric arc furnace. A new control strategy was used based on diode rectifiers and choppers to suppress the effect of flickers and increase efficiency.
Furthermore, Yogesh V et al. [20] described the challenges in PID controller design. A complete literature review was presented on the controller's plan and the control algorithms. The issues faced in the past and the current scenario were addressed satisfactorily. The tuning methods were separated accordingly to internal mode, fractional order, soft computing, and robust control schemes. Additionally, Jignesh Kumar Patel et al. [21] provided various digital controllers in any power controller network. There were different types of controllers like traditional analog, advanced hybrid, and technological digital controllers. The control algorithms might vary from a simple to an advanced artificial intelligence-based control. The evolution of DC converters to power electronic converters happened with a mono level switch to multi-level converter topologies.
Further, Wan-Rone Liou et al. [22] adapted a PWM array, with analog to digital controllers (input), digital to analog converters (output), and a processor control unit for power controller circuits. An advanced hybrid control algorithm was adapted to attain a unity power factor. A higher efficient power conversion was achieved by this method. The acquired power factor was very close to unity, and the ripple voltage performance was close to 100%. In addition, Ricardo Lucio et al. [23] introduced an active control algorithm for the non-linear and changing load. This filter-based control algorithm was used in an electric arc furnace as the load is non-linear and dynamic [24]. The output was used as a reference and fed into the input circuit for power factor corrections.
Moreover, Yu-Wei Liu et al. [25] demonstrated static VAR compensator (SVC) application and active filter for power quality improvement connecting the EAF. Simulation study confirmed the enhancement notably power factor and balance load current. Further, fuzzy logic control was adapted for the optimal design of SVC to enhance the voltage profile of the system connecting the EAF [26]. The compensating device rapidly controlled the system parameters that enhance the voltage profile of the system and reduced harmonic currents. Moreover, a novel topology was developed by Ebrahim Babaei et al. [27] based on the application of dynamic voltage restorer (DVR) and direct converters. This scheme verified its capability for compensation of voltage distortions.
Also, Ahsan Habib et al. demonstrated the effectiveness of DVR to alleviate the power quality disturbances using a phase-locked loop, proportional integral, and supercapacitors. The proposed scheme offered a better efficacy in power quality [28]. Moreover, the synchronous detection method and digital control based on instantaneous power theory were demonstrated for the control active power filter. The digital management offered better power quality than the synchronous detection method [29].
Consolidating all the reports, a unique EAF model with advanced control technology is required to enhance the system power quality, namely, integrated innovative power converters with compensating devices. From the literature surveys, it is found that the application of matrix converter (MC) along with static VAR compensator (SVC) was not demonstrated for electric arc furnace to enhance the power quality. Notably, MC is attracting more attention recently due to its exciting features, namely compact design, bidirectional power flow, controllable input reactive power, and sinusoidal input/output currents [30]. In addition, they have stretched a good height of technological maturity that permits their practical and industrial application in a variety of domains, notably industrial drives, power supplies, and aerospace applications [31]. Based on the limitations from surveys and advantages of MC, this work focuses on the following objects:

•
To design the cutting-edge electric furnace model for a virtual demonstration.

•
To adopt the advanced power converters for EAF.

•
To integrate the compensating devices along with advanced power converters.

•
To improve the overall performance of the power supply, such as arc voltage, arc current, THD I (Current THD), THD V (Voltage THD), power factor, and voltage flicker.
Considering the above objectives, this article organized as follows: Section 2 demonstrates the proposed methodology comprised of various components. Section 3 describes the detailed results and discussion based on the observed outcomes from the simulation. Subsequently, a comparative analysis between various models is performed in Section 4. Finally, conclusions are made based on the observed results in Section 5.

Proposed Methodologies
This section illustrates the proposed scheme comprised of Source, HV/MV transformer, SVC, furnace transformer, Matrix converter along with DSP based controller and the electric furnace as demonstrated in Figure 1. The design parameters of the SVC comprises of 415 V, 8 MVA rated capacity with 22.5 mH of reactor bank paralleled with 223.6 µF of capacitor bank. The impedances of source and furnace transformers are considered as 0.052 + j0.46 and 0.336 + j3.23 respectively with system frequency of 50 Hz. Moreover, the input fuction of the EAF is descried using the following syntax: function v = fcn(f,i) C = 23,000; D = 5000; m = 0.8; Vat0 = 200; vt = Vat0×(1 + (m×f)); v = sign(i)×(vt + (C/(D + abs(i)))); Electronics 2021, 10, x FOR PEER REVIEW 4 of 20 power converters with compensating devices. From the literature surveys, it is found that the application of matrix converter (MC) along with static VAR compensator (SVC) was not demonstrated for electric arc furnace to enhance the power quality. Notably, MC is attracting more attention recently due to its exciting features, namely compact design, bidirectional power flow, controllable input reactive power, and sinusoidal input/output currents [30]. In addition, they have stretched a good height of technological maturity that permits their practical and industrial application in a variety of domains, notably industrial drives, power supplies, and aerospace applications [31]. Based on the limitations from surveys and advantages of MC, this work focuses on the following objects:  To design the cutting-edge electric furnace model for a virtual demonstration.  To adopt the advanced power converters for EAF.  To integrate the compensating devices along with advanced power converters.  To improve the overall performance of the power supply, such as arc voltage, arc current, THDI (Current THD), THDV (Voltage THD), power factor, and voltage flicker.
Considering the above objectives, this article organized as follows: Section 2 demonstrates the proposed methodology comprised of various components. Section 3 describes the detailed results and discussion based on the observed outcomes from the simulation. Subsequently, a comparative analysis between various models is performed in Section 4. Finally, conclusions are made based on the observed results in Section 5.

Proposed Methodologies
This section illustrates the proposed scheme comprised of Source, HV/MV transformer, SVC, furnace transformer, Matrix converter along with DSP based controller and the electric furnace as demonstrated in Figure 1. The design parameters of the SVC comprises of 415 V, 8 MVA rated capacity with 22.5 mH of reactor bank paralleled with 223. 6 of capacitor bank. The impedances of source and furnace transformers are considered as 0.052 + j0.46 and 0.336 + j3.23 respectively with system frequency of 50 Hz. Moreover, the input fuction of the EAF is descried using the following syntax: function v = fcn(f,i) C = 23,000; D = 5000; m = 0.8; Vat0 = 200; vt = Vat0 × (1 + (m×f)); v = sign(i) × (vt + (C/(D + abs(i)))); A detailed description of various elements of the proposed scheme is discussed below.

Matrix Converter (MC)
The proposed scheme uses a matrix converter and an input filter that supplies power to the electric furnace, as illustrated in Figure 2. The output voltage and current of the MC to input voltage and current are derived as follows [30][31][32][33]: where S T denotes a transpose of matrix S, and states of each bidirectional switches are represented as S xy (x indicates A, B, and C and y denote a state a, b, and c) that can be derived as follows: Electronics 2021, 10, x FOR PEER REVIEW 5 of 20

Matrix Converter (MC)
The proposed scheme uses a matrix converter and an input filter that supplies power to the electric furnace, as illustrated in Figure 2. The output voltage and current of the MC to input voltage and current are derived as follows [30][31][32][33]: where S T denotes a transpose of matrix S, and states of each bidirectional switches are represented as Sxy (x indicates A, B, and C and y denote a state a, b, and c) that can be derived as follows: MC uses the space vector modulation (SVM) control algorithm that represents the three-phase current and voltage on the vector plane. Each output phase is given as an input to the stage considering the states of switches. A total of twenty-seven switching states are admissible to evade the short and open circuit in the incoming side using the above functions. Among the combinations, three groups are formed based on the output phases relating to the respective input phases. The output of the MC is based on the SVM parameters such as instantaneous voltage and current, and phase angles of the input (∝ and output voltages (∝ ). Moreover, a duty period for each switching operation is computed to attain the desired output voltage and frequency referring at the MC. The below equations represent a switching time concerning two-phase angles. MC uses the space vector modulation (SVM) control algorithm that represents the three-phase current and voltage on the vector plane. Each output phase is given as an input to the stage considering the states of switches. A total of twenty-seven switching states are admissible to evade the short and open circuit in the incoming side using the above functions. Among the combinations, three groups are formed based on the output phases relating to the respective input phases. The output of the MC is based on the SVM parameters such as instantaneous voltage and current, and phase angles of the input (∝ i ) and output voltages (∝ 0 ). Moreover, a duty period for each switching operation is computed to attain the desired output voltage and frequency referring at the MC. The below equations represent a switching time concerning two-phase angles.
Further, the MC input current and the output voltage are estimated using the below equations.
where 'a' is an operator that can be represented as e j( 2π 3 ) . Then the terms V x and I x (x = a, b, c) are the output voltages and input currents of the MC respectively. Moreover, the term V 0 max and I i max are the scale of output voltage and input current, respectively, and the term ∝ 0 and β i are the angles (voltage and current respectively). Further, various switching operations states and the respective output voltage and the input current are illustrated in Table 1 derived using a DSP based controller. Table 1. States of switches and their respective input and output.

On States of Switches
Further, the input filter circuit is designed using a capacitor (C f ), inductor (L f ), and resistor (R s ), and the equivalent single-phase model is illustrated in Figure 3. Electronics 2021, 10, x FOR PEER REVIEW 7 of 20 From the above figure, the input current Is(s) is expressed as the function of the input voltage (Vs) and MC input current (IMC). Further, the frequency response of the output voltage and current of the filter (i.e., input voltage and current to MC) is expressed as follows: The canonical representation of the above equations are expressed as follows: where , and Q denotes the natural frequency, damping factor, and quality factor, respectively.

Furnace Transformer
The furnace transformer involves a unique design, and its circuit equation can be derived as follows: where defines the impedance of the furnace transformer that can be formulated using Equation (13). Further, the term and denote the electrode current and source voltage, respectively.

=
. + where R1 and X1 are the resistance and reactance of the transformer, and they can be represented as below: From the above figure, the input current I s (s) is expressed as the function of the input voltage (V s ) and MC input current (I MC ). Further, the frequency response of the output voltage and current of the filter (i.e., input voltage and current to MC) is expressed as follows: The canonical representation of the above equations are expressed as follows: where ω n , ξ and Q denotes the natural frequency, damping factor, and quality factor, respectively.

Furnace Transformer
The furnace transformer involves a unique design, and its circuit equation can be derived as follows: where Z 1 defines the impedance of the furnace transformer that can be formulated using Equation (13). Further, the term I e and U 1 denote the electrode current and source voltage, respectively.
where R 1 and X 1 are the resistance and reactance of the transformer, and they can be represented as below: where P EF and P arc are the furnace and arc power, respectively.

SVC
To obtain steady-state power for EAF and improvement of voltage profile, SVC is adapted that can inject or absorb the reactive power based on the incoming circuit nature [34,35]. It consists of a fixed capacitor, inductor and thyristor controlled rectifier, as illustrated in Figure 4. The total reactive power injection or absorption of the device can be expressed as follows [30,31]: where 'B' denotes a susceptance offered by the SVC that can control the reactive power (positive value terms the injection and negative scale represent the absorption) and V represents the voltage. The range of the susceptance can be formulated as follows: where S b represent the base power in MVA, X T pu is the transformer reactance in per unit, Q cap and Q ind are the reactive capacitance and reactive inductive, respectively, and B max and B min are the maximum and minimum reactive power of the capacitor and inductor, respectively. The total capacitance required for the design is calculated using the following equation.
where and are the furnace and arc power, respectively.

SVC
To obtain steady-state power for EAF and improvement of voltage profile, SVC is adapted that can inject or absorb the reactive power based on the incoming circuit nature [34,35]. It consists of a fixed capacitor, inductor and thyristor controlled rectifier, as illustrated in Figure 4. The total reactive power injection or absorption of the device can be expressed as follows [30,31]: where 'B' denotes a susceptance offered by the SVC that can control the reactive power (positive value terms the injection and negative scale represent the absorption) and V represents the voltage. The range of the susceptance can be formulated as follows: where represent the base power in MVA, is the transformer reactance in per unit, and are the reactive capacitance and reactive inductive, respectively, and and are the maximum and minimum reactive power of the capacitor and inductor, respectively. The total capacitance required for the design is calculated using the following equation.   The following condition needs to satisfy for adequate compensation: Electronics 2021, 10, 1125 9 of 20

Electric Arc Furnace (EAF)
The modeling of EAF is performed based on the V-I Characteristics (VIC), which comprises a solution of a non-linear differential equation that meticulously approximates the actual arc furnace. The accurate and linearized model VIC is compared to justify the precision between them as represented in Figure 5. The vital parameters such as ignition and extinction voltage are considered to determine the arc length during the operation. Various time-domain models can be derived by approximating the actual VIC and described in the following sub-sections.

Electric Arc Furnace (EAF)
The modeling of EAF is performed based on the V-I Characteristics (VIC), which comprises a solution of a non-linear differential equation that meticulously approximates the actual arc furnace. The accurate and linearized model VIC is compared to justify the precision between them as represented in Figure 5. The vital parameters such as ignition and extinction voltage are considered to determine the arc length during the operation. Various time-domain models can be derived by approximating the actual VIC and described in the following sub-sections.

Approximation Model
Based on the characteristic plot of V-I (voltage-current), a linear piecewise model EAF is derived. With the arc length during arc furnace operation, the ignition voltage ( ig V ) and extinction voltage of arc ( ex V ) are determined. The actual furnace model is derived in a virtual platform using two linear equations. Therefore, the complete on cycle model is considered, and the relation between voltages of arc and current of arc is described as follows:

Approximation Model
Based on the characteristic plot of V-I (voltage-current), a linear piecewise model EAF is derived. With the arc length during arc furnace operation, the ignition voltage (V ig ) and extinction voltage of arc (V ex ) are determined. The actual furnace model is derived in a virtual platform using two linear equations. Therefore, the complete on cycle model is considered, and the relation between voltages of arc and current of arc is described as follows: where 'S 1 'and 'S 2 ' represent a linear slope achieved from VIC approximation between the limits −i1 and, i1 and i2 respectively; i1 and i2 are the arc current attained at the ignition extinction voltage of the arc, respectively.

Piecewise Model
The accurate piecewise non-linear model can be developed by assuming a portion of V-I characteristics. The processes of melting of arc are divided into different sections. Initially, the magnitude of the voltage rises to ignition voltage v ig from extinction voltage −v ex . Then, the resistor acts as a furnace arc, and the polarity of current varies from i 3 to i 1 . Secondly, the dissolving process gets started. Henceforth, an unexpected voltage drop of exponential through the electrode has occurred, and therefore voltage of the arc is reduced to v st from v ig . Moreover, the current of the arc rises lightly from i 1 to i 2 . Finally, a general dissolving procedure has taken place, i.e., the voltage of the arc linearly falls smoothly and slows down from v st to v ex , as described in Equation (26).
where S 1 , S 2 , and S 3 are the equivalent slopes of each section.

Hybrid Model (Exponential-Hyperbolic)
The exponential furnace model is derived from V-I characteristics, and it can be derived as follows: where V e denotes the arc voltage derived from the exponential model; V at represent the threshold voltage; i defines the arc current per phase; and I 0 denotes a current constant that represents the positive and negative steepness of the model. The hyperbolic furnace model derived from the same VIC using the following equation.
where V h denotes the arc voltage obtained from the hyperbolic model; the variables C and D represent the arc power and current. Then the hybrid model (V hyb ) is developed by combining both models, i.e., exponential and hyperbolic. It can be formulated using the below equation.
f or high curent (30) where V at = A + B.l; A and B are the measurements from the experimental formula; and l represent the arc length in centimeters. Further, the sinusoidal flicker in the power system is derived using the below equation.
where m and ω f denotes a modulation index and flicker frequency, respectively. It is a known fact that the flicker measurement is based on the RMS voltage of the system and its respective frequency. The percentage measurement of flicker is computed using the equation below.
where V 2p and V 1p represent the upper and lower peak voltage, respectively. After substituting the above equations, the percentage of voltage flicker is derived as follows:

Results and Discussions
The comprehensive model is designed in MATLAB Simulink software, and the simulations are done for different cases. The input voltage and current, and the corresponding output are studied for the three models. It consists of a three-phase input source shifted by the angle 120 • apart. The voltage-controlled source is adapted as a non-linear time-varying case that represents the furnace model. The complete description of the model developed in Simulink is illustrated in Figure 6. The output of the system is a non-linear time-varying voltage that can be generated due to the input given as arc current. The model's vital parameters can be extracted, such as three-phase voltage and current and THD for two cases, namely with and without SVC. In addition, flicker measurements are carried out using Figure 7 that can be implemented in the SIMULINK. The proposed system is simulated to demonstrate the power quality of the supply by illustrating the voltage and current harmonics, power factor, and voltage flicker. The complete description of the observed results is discussed in the following subsections.

Current and Voltage Waveforms
As stated earlier, the application of MC is simulated for two conditions, namely with and without SVC integration into the developed model. The input voltage and current for the matrix converter are derived from the filter circuit, as illustrated in Figure 8a and Figure 8b respectively. It is observed that the waveforms exhibit a controlled three-phase The proposed system is simulated to demonstrate the power quality of the supply by illustrating the voltage and current harmonics, power factor, and voltage flicker. The complete description of the observed results is discussed in the following subsections.

Current and Voltage Waveforms
As stated earlier, the application of MC is simulated for two conditions, namely with and without SVC integration into the developed model. The input voltage and current for the matrix converter are derived from the filter circuit, as illustrated in Figure 8a and Figure 8b respectively. It is observed that the waveforms exhibit a controlled three-phase The proposed system is simulated to demonstrate the power quality of the supply by illustrating the voltage and current harmonics, power factor, and voltage flicker. The complete description of the observed results is discussed in the following subsections.

Current and Voltage Waveforms
As stated earlier, the application of MC is simulated for two conditions, namely with and without SVC integration into the developed model. The input voltage and current for the matrix converter are derived from the filter circuit, as illustrated in Figure 8a,b respectively. It is observed that the waveforms exhibit a controlled three-phase input that can be given to the MC to meet the demand of the non-linear load (EAF). This is due to adapting compensating devices that maintain a controlled input to the converting segment. Further, the waveforms of arc currents are illustrated in Figure 9 for both cases. It is observed that there is a trivial variation of current magnitude between the hybrid model with MC and a hybrid model with MC and SVC, i.e., 121.59 kA, and 123.26 kA, respectively. The wave shapes of both cases are nearly similar, with a slight variation in the angle.
Similarly, the waveform for arc voltages is computed and illustrated in Figure 10. It is observed that there is a variation in the voltage magnitude between the two cases as described in the arc current. The voltage magnitudes are logged as 308 V and 314 V, i.e., with MC and MC-SVC. It is observed that the proposed system injects the required voltage to the source that could stabilize the arc voltages commendably.  Similarly, the waveform for arc voltages is computed and illustrated in Figure 10. It is observed that there is a variation in the voltage magnitude between the two cases as described in the arc current. The voltage magnitudes are logged as 308 V and 314 V, i.e., with MC and MC-SVC. It is observed that the proposed system injects the required voltage to the source that could stabilize the arc voltages commendably.

Harmonic Analysis
The analysis of current harmonics is carried out for both cases and the respective THDs are illustrated in Figure 11. It is observed that the hybrid model with MC shows the least THD of about 3.16%. In addition, the THD of the hybrid model with MC and

Harmonic Analysis
The analysis of current harmonics is carried out for both cases and the respective THDs are illustrated in Figure 11. It is observed that the hybrid model with MC shows the least THD of about 3.16%. In addition, the THD of the hybrid model with MC and SVC condense the rate further reached about 2.85%, which is the smallest compared with the hybrid model with MC. This is due to the enhancement of power quality parameters with SVC integration. (b)

Harmonic Analysis
The analysis of current harmonics is carried out for both cases and the respective THDs are illustrated in Figure 11. It is observed that the hybrid model with MC shows the least THD of about 3.16%. In addition, the THD of the hybrid model with MC and SVC condense the rate further reached about 2.85%, which is the smallest compared with the hybrid model with MC. This is due to the enhancement of power quality parameters with SVC integration. Subsequently, the voltage harmonics are evaluated, and the respective characteristics are illustrated in Figure 12. From the analysis, it is perceived that the THD of the SVC model logged a better range of about 29.54%, which is exceptionally great compared with the MC model (42.58%).
(a) Subsequently, the voltage harmonics are evaluated, and the respective characteristics are illustrated in Figure 12. From the analysis, it is perceived that the THD of the SVC model logged a better range of about 29.54%, which is exceptionally great compared with the MC model (42.58%).
(b) Figure 11. Current harmonics at PCC (a) Hybrid with MC, (b) Hybrid with MC and SVC.
Subsequently, the voltage harmonics are evaluated, and the respective characteristics are illustrated in Figure 12. From the analysis, it is perceived that the THD of the SVC model logged a better range of about 29.54%, which is exceptionally great compared with the MC model (42.58%). It is noted that the proposed compensating scheme enhances not only the power factor of the system but also aids in maintaining the THD level of the system within a band, as described earlier. It is noted that the proposed compensating scheme enhances not only the power factor of the system but also aids in maintaining the THD level of the system within a band, as described earlier.

Power Factor
After compensation, the systems power factor is measured with respect to time. SVC injected the reactive power to a great extent to attain a better power factor, as demonstrated in Figure 13. The load current combines with the compensating current of the SVC that affects the closer to unity power factor, i.e., 0.9975. This ensures a superior power quality enhancement for high non-linear loads, notably EAF.

Power Factor
After compensation, the systems power factor is measured with respect to time. SVC injected the reactive power to a great extent to attain a better power factor, as demonstrated in Figure 13. The load current combines with the compensating current of the SVC that affects the closer to unity power factor, i.e., 0.9975. This ensures a superior power quality enhancement for high non-linear loads, notably EAF.

Voltage Flicker
The magnitude of voltage flicker is computed using dynamic characteristics that represent the melting process of the furnace. This operation exhibits severe voltage flickering, and this can be derived through simulation study based on Equation (34). The evaluation of voltage flicker can be considered as continuous voltage sags and swells. The proposed compensating system, i.e., SVC can compensate voltage sag and swell as well as voltage flicker. The observed results of flickering for voltage waveform and the respective current components for a hybrid model with MC and SVC are illustrated in Figure 14. It is known that there would be severe evidence of flicker during the melting process of the furnace. However, the proposed model logged the most petite range than the hybrid model with MC.

Voltage Flicker
The magnitude of voltage flicker is computed using dynamic characteristics that represent the melting process of the furnace. This operation exhibits severe voltage flickering, and this can be derived through simulation study based on Equation (34). The evaluation of voltage flicker can be considered as continuous voltage sags and swells. The proposed compensating system, i.e., SVC can compensate voltage sag and swell as well as voltage flicker. The observed results of flickering for voltage waveform and the respective current components for a hybrid model with MC and SVC are illustrated in Figure 14. It is known that there would be severe evidence of flicker during the melting process of the furnace. However, the proposed model logged the most petite range than the hybrid model with MC.

Power Factor
After compensation, the systems power factor is measured with respect to time. SVC injected the reactive power to a great extent to attain a better power factor, as demonstrated in Figure 13. The load current combines with the compensating current of the SVC that affects the closer to unity power factor, i.e., 0.9975. This ensures a superior power quality enhancement for high non-linear loads, notably EAF.

Voltage Flicker
The magnitude of voltage flicker is computed using dynamic characteristics that represent the melting process of the furnace. This operation exhibits severe voltage flickering, and this can be derived through simulation study based on Equation (34). The evaluation of voltage flicker can be considered as continuous voltage sags and swells. The proposed compensating system, i.e., SVC can compensate voltage sag and swell as well as voltage flicker. The observed results of flickering for voltage waveform and the respective current components for a hybrid model with MC and SVC are illustrated in Figure 14. It is known that there would be severe evidence of flicker during the melting process of the furnace. However, the proposed model logged the most petite range than the hybrid model with MC.

Comparative Analysis
The comparative analysis is performed between the proposed and existing model for various power quality parameters such as I peak , V peak , THD V , THD I , voltage flicker, and power factor. The existing models considered in this study are the Cassie model and the hybrid model (exponential-hyperbolic), and these performances are compared with the hybrid-MC and hybrid-MC-SVC model illustrated in Figures 15-17.

Comparative Analysis
The comparative analysis is performed between the proposed and existing model for various power quality parameters such as Ipeak, Vpeak, THDV, THDI, voltage flicker, and power factor. The existing models considered in this study are the Cassie model and the hybrid model (exponential-hyperbolic), and these performances are compared with the hybrid-MC and hybrid-MC-SVC model illustrated in Figures 15-17.

Comparative Analysis
The comparative analysis is performed between the proposed and existing model for various power quality parameters such as Ipeak, Vpeak, THDV, THDI, voltage flicker, and power factor. The existing models considered in this study are the Cassie model and the hybrid model (exponential-hyperbolic), and these performances are compared with the hybrid-MC and hybrid-MC-SVC model illustrated in Figures 15-17. From the above figures, it is perceived that the peak voltage and current of the proposed model show a more excellent value of 314 V and 123.26 kA, respectively, which are more significant than other models. Moreover, the current and voltage THD is less for the proposed model (2.8% and 29.54%, respectively), as illustrated in the above figures. Further, the voltage flicker is compared with other existing models, and it shows a minor percentage of 1.26%. Finally, the power factor of the proposed scheme exhibits a higher value of 0.9975, which is greater than the other existing models. The overall performance of the proposed model shows more excellent value due to their combined function of MC and SVC. From the above figures, it is perceived that the peak voltage and current of the proposed model show a more excellent value of 314 V and 123.26 kA, respectively, which are more significant than other models. Moreover, the current and voltage THD is less for the proposed model (2.8% and 29.54%, respectively), as illustrated in the above figures. Further, the voltage flicker is compared with other existing models, and it shows a minor percentage of 1.26%. Finally, the power factor of the proposed scheme exhibits a higher value of 0.9975, which is greater than the other existing models. The overall performance of the proposed model shows more excellent value due to their combined function of MC and SVC. From the above figures, it is perceived that the peak voltage and current of the proposed model show a more excellent value of 314 V and 123.26 kA, respectively, which are more significant than other models. Moreover, the current and voltage THD is less for the proposed model (2.8% and 29.54%, respectively), as illustrated in the above figures. Further, the voltage flicker is compared with other existing models, and it shows a minor percentage of 1.26%. Finally, the power factor of the proposed scheme exhibits a higher value of 0.9975, which is greater than the other existing models. The overall performance of the proposed model shows more excellent value due to their combined function of MC and SVC.
Considering all these inferences, it is observed that the proposed model with MC and SVC enhances the quality of the power supply, and this can be applied to the real-time furnace operation for effective characteristics.

Conclusions
This work demonstrated an advanced time-domain EAF model with DSP-based MC and SVC. This proposed model enhanced the overall power quality of the system. The following conclusions are made based on the observed results:

•
The proposed model offers superior outcomes compared with existing EAF models. With these enhanced outcomes, the proposed method can be adapted for real-time application i.e., a steel manufacturing plant that can offer enriched power quality with energy-efficient operation.