Methodology for Quantitative Assessment of Greenhouse Gas Emissions Reduction of Solar-Powered Wi-Fi

In this paper, a modeling framework to quantify the reduction of potential greenhouse gas (GHG) emissions when using solar-powered Wi-Fi as an internet access point is developed and tested. This framework includes newly developed MATLAB code and the use of the ATOLL tool for energy consumption and network optimization, respectively. A practical case study is described with scenarios enabling different signal coverage on a university campus. These scenarios are based on technical requirements, including number of access points, budget link, and access duration. Four hundred tons of GHG can be reduced each year if solar Wi-Fi is deployed in solar campuses, which represents 5.5 × 10−5 percent of the total GHG produced by the telecommunications sector. A direct relationship between the number of access points and coverage signal quality on the one hand and energy consumption on the other hand is established. We use this case study to forecast the potential GHG mitigation if a wider deployment of the community Wi-Fi is achieved. This methodology could also be used to estimate GHG reductions when other wireless technologies are deployed.


Introduction
There is overwhelming scientific evidence that human activity is the biggest contributor to climate change through greenhouse gas (GHG) emissions. The production and utilization of fossil-based energy sources are the largest contributors to anthropogenic GHG emissions [1]. The Intergovernmental Panel on Climate Change (IPCC) suggested limiting global warming to 1.5 • C above preindustrial levels [2], requiring the development and deployment of cleaner energy technologies. These clean technologies should provide significant GHG reductions with a large potential market capture. Currently, transport, industrial activities, and building are the largest economic sectors driving fossil energy demand. The information and communication technology (ICT) sector is receiving relatively little attention. Recent reports showed that in the worst-case scenario, this sector could become a dominant energy user, potentially consuming as much as half of global electricity in 2030 [3]. Another report indicated that the overall carbon footprint of the ICT sector is expected to increase significantly [4].
The deployment of 5G networks and the prevalence of Internet of Things (IoT) devices will continue to drive the fast growth of energy demand in the ICT sector. Energy demand for IoT devices is expected to increase by a factor of 17 between 2016 and 2025 [4]. This will add additional pressure to current commitments to reduce GHG emissions, particularly if there is no significant reduction in other sectors. Indeed, a growing global economy and increasing energy demand, combined with a lack of cost-competitive, large-scale renewable power generation, has led to increasing emissions [5]. Even with increasing renewable energy, demand for coal and natural gas will continue to grow due to increasing global electricity demand. Improved efficiency at the device level (TV monitors, smartphones, internet. The majority of these students have limited internet access at home. The cost structure of a wireless network subscription is often prohibitive. Local authorities are trying to provide free access, albeit with limited strategies for deploying sustainable solutions. In particular, with the dominance of fossil electricity and the abundance of solar energy, photovoltaic-powered wireless networks could provide sustainable deployment of Wi-Fi in most university campuses and other communities.
In this paper, we will describe a new bottom-up GHG calculation framework to account for the deployment of community-based Wi-Fi-powered solar energy. This framework also includes a methodology to estimate energy consumption as a function of the number of Wi-Fi access points using newly developed MATLAB code. We will use a specific case study related to a university campus to assess the GHG reduction mitigation impact if the proposed solar Wi-Fi solution is deployed at the country scale.

Materials and Methods
The proposed methodology summarized in Figure 1 includes 5 key steps. Key outputs for each step are also indicated. Details of each tool are described in more detail in this section. university campuses, students often rely on free Wi-Fi networks to access the intern majority of these students have limited internet access at home. The cost structu wireless network subscription is often prohibitive. Local authorities are trying to p free access, albeit with limited strategies for deploying sustainable solutions. In par with the dominance of fossil electricity and the abundance of solar energy, photov powered wireless networks could provide sustainable deployment of Wi-Fi in mo versity campuses and other communities.
In this paper, we will describe a new bottom-up GHG calculation framework count for the deployment of community-based Wi-Fi-powered solar energy. This work also includes a methodology to estimate energy consumption as a function number of Wi-Fi access points using newly developed MATLAB code. We will use cific case study related to a university campus to assess the GHG reduction mit impact if the proposed solar Wi-Fi solution is deployed at the country scale.

Materials and Methods
The proposed methodology summarized in Figure 1 includes 5 key steps. K puts for each step are also indicated. Details of each tool are described in more d this section.

System Boundary: Case Study
A bottom-up approach is used to assess the potential GHG impact for deploy lar-powered Wi-Fi on university campuses. To develop this methodology, we cons a practical case study. Standalone Wi-Fi ( Figure 2) was sized and built at the N High School of Technology (École National Supérieur de Technologie (ENST)) c near Algiers (Algeria). Mini-solar modules were installed along the Wi-Fi post. T sign provides more flexibility to satisfy variable energy demand.

System Boundary: Case Study
A bottom-up approach is used to assess the potential GHG impact for deploying solar-powered Wi-Fi on university campuses. To develop this methodology, we considered a practical case study. Standalone Wi-Fi ( Figure 2) was sized and built at the National High School of Technology (École National Supérieur de Technologie (ENST)) campus near Algiers (Algeria). Mini-solar modules were installed along the Wi-Fi post. This design provides more flexibility to satisfy variable energy demand. In this case study, we modeled the signal coverage and energy requirements to cover the whole ENST campus using Wi-Fi technology based on a standalone Wi-Fi-powered post. Each Wi-Fi post will be referred to as a base station (BS) in this paper. Each element of the network is analyzed to estimate the energy consumption of the network. Next, the carbon footprint of electricity consumption has been estimated when using two sources of electricity: fossil energy (baseline) and solar energy. This will help estimate the potential GHG mitigation through the wider deployment of solar-powered Wi-Fi stations.
The sizing and planning of wireless networks are very critical steps. The overall electricity consumption is estimated for the different design scenarios. The resources (bandwidth, frequency, equipment) required to satisfy all potential subscribers within the campus will be first estimated. Solutions to overcoming potential technical constraints during deployment are also provided. Dimensioning a Wi-Fi network is based on two main criteria: coverage and capacity. For this purpose, we developed a user interface using MATLAB, and we optimized this network using the ATOLL telecommunications network simulator. Once we completed system dimensioning, energy consumption was thus estimated, allowing quantification of the carbon footprints.

Wi-Fi Network Design
In order to design the Wi-Fi network with a graphical interface, we developed a MATLAB code using the Graphical User Interface Development Environment (GUIDE) function, which is based on different graphical objects (functions "handles", "properties of the objects", "callbacks"). Below, the key equations used to develop the MATLAB code are described.

Wi-Fi Network Coverage Design
The first step in system dimensioning involves determining the number of BS transmitters required to cover the whole campus. For this, we needed to estimate the maximum path loss following the approach described in [19]. Then, the link budget was calculated to determine whether the power level received will be sufficient for the link to function correctly and also assess the quality of the signal. This parameter is difficult to assess, as it depends on the user's needs. Wi-Fi transmitters required for optimal Wi-Fi coverage were installed on solar-powered street lighting poles to minimize cost and GHG impacts. In this case study, we modeled the signal coverage and energy requirements to cover the whole ENST campus using Wi-Fi technology based on a standalone Wi-Fi-powered post. Each Wi-Fi post will be referred to as a base station (BS) in this paper. Each element of the network is analyzed to estimate the energy consumption of the network. Next, the carbon footprint of electricity consumption has been estimated when using two sources of electricity: fossil energy (baseline) and solar energy. This will help estimate the potential GHG mitigation through the wider deployment of solar-powered Wi-Fi stations.
The sizing and planning of wireless networks are very critical steps. The overall electricity consumption is estimated for the different design scenarios. The resources (bandwidth, frequency, equipment) required to satisfy all potential subscribers within the campus will be first estimated. Solutions to overcoming potential technical constraints during deployment are also provided. Dimensioning a Wi-Fi network is based on two main criteria: coverage and capacity. For this purpose, we developed a user interface using MATLAB, and we optimized this network using the ATOLL telecommunications network simulator. Once we completed system dimensioning, energy consumption was thus estimated, allowing quantification of the carbon footprints.

Wi-Fi Network Design
In order to design the Wi-Fi network with a graphical interface, we developed a MATLAB code using the Graphical User Interface Development Environment (GUIDE) function, which is based on different graphical objects (functions "handles", "properties of the objects", "callbacks"). Below, the key equations used to develop the MATLAB code are described.

Wi-Fi Network Coverage Design
The first step in system dimensioning involves determining the number of BS transmitters required to cover the whole campus. For this, we needed to estimate the maximum path loss following the approach described in [19]. Then, the link budget was calculated to determine whether the power level received will be sufficient for the link to function correctly and also assess the quality of the signal. This parameter is difficult to assess, as it depends on the user's needs. Wi-Fi transmitters required for optimal Wi-Fi coverage were installed on solar-powered street lighting poles to minimize cost and GHG impacts.
In order to determine the path loss (PL), different propagation models were considered. The most suitable model for the Wi-Fi network is the Egli model [19]. The Egli model for median path loss over irregular terrain is The power components of the link budget related to the transmitter side are critical. This is often represented by the effective isotropic radiated power (EIRP), given by: where P t : transmit power (dBm); L c : cable loss (dB); G a : transmitter antenna gain (dBi).
The power component of the link budget related to the receiver side is represented by the received power (P r ): where PL: path loss (dB); G R : receiver antenna gain (dBi).
In order to properly detect the transmitted signal, the following conditions must be satisfied.
Received power > Receiver sensitivity (4) The proposed coverage design of the Wi-Fi-based BS allows us to determine the number of cells to optimize signal coverage. The total number of cells is given by: where R is the range of each BS. The number of access points (NPC) for each cell is determined by the following ratio: where BPT: total bandwidth; BPP: bandwidth offered by an access point.
The total number of access points (NPT) in the network will then be: It is important to estimate the number of users that can be managed by a single access point in order to determine the number of access points within a coverage area.
Determining the type of application (data, voice, video) determines the nature of traffic the network must carry. This ensures that the performance of the network meets the needs of the users.
To determine the total capacity of the system, the maximum individual throughput needed for each service offered must be determined. Table 1 provides typical bandwidth values for the main supported services. In order to support the different services, we need to have sufficient bandwidth within the proposed network. The bandwidth (BBT) is calculated using the following equation: where n j : number of subscribers served by service j; c j : bandwidth by subscribers for service j; t j : concurrency rate for the category of subscribers served by the service.

Planning and Optimization of the Network Using ATOLL
ATOLL software is used for the design and optimization of Wi-Fi networks. It allows optimizing frequency distribution within the outdoor environment to minimize the co-channel interference and to find the optimal location and number of access points. The following steps are considered in planning a wireless network using the ATOLL software [21]:

•
Creation of a new project by choosing wireless technology.

•
The precision of the geographic coordinate format, in our case related to the coordinates of the ENST and the region of Algiers. • Importing maps of the relevant region with terrain features. • Configuring radio frequency bandwidth work parameters. The ACP module is critical and allows the optimization of networks and automatically calculating the optimal parameters in terms of coverage and quality of the signal. ACP Electronics 2021, 10, 2829 7 of 16 removes unnecessary sites or sectors or chooses from candidate sites that can be added to improve network performance. The ACP module can also adjust the power, tilt, and azimuth of antennas. The optimization process is based on a cost function. The cost decreases when the level of coverage and quality of the signal increase. The iterative algorithm is used for each iteration when one network parameter is changed. Scenarios obtained from the different changes are ranked based on the cost function. When using the ACP, we need to specify the objectives and enable only the parameters that we wish to change during the optimization.

Results and Discussion
Using the methodology described above, we will first provide results related to the ENST campus case study. Afterwards, we will estimate the potential GHG mitigation. This approach will be generalized to include any Wi-Fi community using solar energy to replace fossil sources.

Optimal Coverage
In order to evaluate the Wi-Fi network radio budget in the proposed site, an access point with a consumption of 12 W and high radiation power of 27 dBm was selected. The technical characteristics are shown in Appendix A (Table A1). Before the calculation, to find the optimal coverage, characteristics of the equipment were introduced in the simulator including access points, antennas, and cable losses. Figure 3 summarizes the input-output data using MATLAB code. If the receiver sensitivity is lower than the received power (−28 dBm), the connection is enabled. decreases when the level of coverage and quality of the signal increase. The iterative algorithm is used for each iteration when one network parameter is changed. Scenarios obtained from the different changes are ranked based on the cost function. When using the ACP, we need to specify the objectives and enable only the parameters that we wish to change during the optimization.

Results and Discussion
Using the methodology described above, we will first provide results related to the ENST campus case study. Afterwards, we will estimate the potential GHG mitigation. This approach will be generalized to include any Wi-Fi community using solar energy to replace fossil sources.

Optimal Coverage
In order to evaluate the Wi-Fi network radio budget in the proposed site, an access point with a consumption of 12 W and high radiation power of 27 dBm was selected. The technical characteristics are shown in Appendix A (Table A1). Before the calculation, to find the optimal coverage, characteristics of the equipment were introduced in the simulator including access points, antennas, and cable losses. Figure 3 summarizes the inputoutput data using MATLAB code. If the receiver sensitivity is lower than the received power (−28 dBm), the connection is enabled. Using the MATLAB code, we estimated that at least five Wi-Fi access points to cover the whole campus are required. The impact of using lower and higher numbers of access points was also assessed. Figure 4 provides the optimal site for the five Wi-Fi access points.  Using the MATLAB code, we estimated that at least five Wi-Fi access points to cover the whole campus are required. The impact of using lower and higher numbers of access points was also assessed. Figure 4 provides the optimal site for the five Wi-Fi access points. decreases when the level of coverage and quality of the signal increase. The iterative algorithm is used for each iteration when one network parameter is changed. Scenarios obtained from the different changes are ranked based on the cost function. When using the ACP, we need to specify the objectives and enable only the parameters that we wish to change during the optimization.

Results and Discussion
Using the methodology described above, we will first provide results related to the ENST campus case study. Afterwards, we will estimate the potential GHG mitigation. This approach will be generalized to include any Wi-Fi community using solar energy to replace fossil sources.

Optimal Coverage
In order to evaluate the Wi-Fi network radio budget in the proposed site, an access point with a consumption of 12 W and high radiation power of 27 dBm was selected. The technical characteristics are shown in Appendix A (Table A1). Before the calculation, to find the optimal coverage, characteristics of the equipment were introduced in the simulator including access points, antennas, and cable losses. Figure 3 summarizes the inputoutput data using MATLAB code. If the receiver sensitivity is lower than the received power (−28 dBm), the connection is enabled. Using the MATLAB code, we estimated that at least five Wi-Fi access points to cover the whole campus are required. The impact of using lower and higher numbers of access points was also assessed. Figure 4 provides the optimal site for the five Wi-Fi access points.

Optimal Capacity
First, we needed to calculate the bandwidth necessary to satisfy the demand for network resources in the ENST campus. We created another tool using MATLAB for this task. Figure 5 summarizes the key inputs and outputs data for the calculation of the necessary bandwidth in the network.

Optimal Capacity
First, we needed to calculate the bandwidth necessary to satisfy the demand for network resources in the ENST campus. We created another tool using MATLAB for this task. Figure 5 summarizes the key inputs and outputs data for the calculation of the necessary bandwidth in the network. As indicated in Figure 4, based on input data and information, we estimated that a total bandwidth of 1198.8 Mbp/s for each Wi-Fi cell is required.

Optimal Network
The ENST campus was used to demonstrate the proposed framework. As the demand for internet signals is significant, the physical position of the Wi-Fi posts is critical. The geographical coordinates of the ENST campus are given in Table 2. As a first step, we needed to optimize the geographical positions where the Wi-Fi posts will be installed. For this, we imported a map of the ENST campus from Google Earth into the ATOLL platform. This will help identify access point locations. Signal pathway propagation, cost of renting, and availability of the sites where the equipment will be installed are critical criteria to choose access point sites. In our case, the radio sites were placed from the global positioning system (GPS) coordinates retrieved from the lighting optimization study of the solar streetlights at the ENST campus ( Figure A1 in Appendix A).
Once the location of the access points and their positions on the geographical map were identified, the frequency distribution for each transmitter on the network and antenna type were selected. During the dimensioning of the previously treated Wi-Fi network, an access point with specific characteristics such as the Wi-Fi compatibility standard, the transmission power, and the working frequency were selected. Afterwards, these parameters were introduced in the simulator code ( Figure A2 in Appendix A). This will help estimate power received by a subscriber at each point. The predicted signal coverage for the ENST campus is shown in Figure 6. This helps assess whether the chosen locations of the access point are suitable. As indicated in Figure 4, based on input data and information, we estimated that a total bandwidth of 1198.8 Mbp/s for each Wi-Fi cell is required.

Optimal Network
The ENST campus was used to demonstrate the proposed framework. As the demand for internet signals is significant, the physical position of the Wi-Fi posts is critical. The geographical coordinates of the ENST campus are given in Table 2. As a first step, we needed to optimize the geographical positions where the Wi-Fi posts will be installed. For this, we imported a map of the ENST campus from Google Earth into the ATOLL platform. This will help identify access point locations. Signal pathway propagation, cost of renting, and availability of the sites where the equipment will be installed are critical criteria to choose access point sites. In our case, the radio sites were placed from the global positioning system (GPS) coordinates retrieved from the lighting optimization study of the solar streetlights at the ENST campus ( Figure A1 in Appendix A).
Once the location of the access points and their positions on the geographical map were identified, the frequency distribution for each transmitter on the network and antenna type were selected. During the dimensioning of the previously treated Wi-Fi network, an access point with specific characteristics such as the Wi-Fi compatibility standard, the transmission power, and the working frequency were selected. Afterwards, these parameters were introduced in the simulator code ( Figure A2 in Appendix A). This will help estimate power received by a subscriber at each point. The predicted signal coverage for the ENST campus is shown in Figure 6. This helps assess whether the chosen locations of the access point are suitable. Electronics 2021, 10, x FOR PEER REVIEW 9 of 16 To assess Wi-Fi coverage, we identified five classes of signal level quality: • Very good coverage corresponds to a signal level higher than −70 dBm. It can be noticed that the coverage is almost complete in the selected area and that the signal level varies between −90 dBm and −70 dBm. However, there are areas where the signal level is low, so there is a degradation in the coverage in these areas. This is due to the fact that the ground presents several obstacles in the direction of these locations, as is the case for some areas where the signal level is −105 dBm.
To minimize interference due to the use of adjacent channels and the use of the same channel, the AFP module from ATOLL was used. The AFP module was used to automatically calculate the total cost, which is the interference rate in the implanted network.
The optimization was performed using the ACP module, which allows the design of networks and automatically calculates the optimal parameters in terms of coverage and quality of the signal. In Table 3, we can see the proposed increases in signal quality and coverage. From Table 3, we notice that there are four modifications: a modification in the transmission power level, a modification of the azimuth level, and the deactivation of the two sites to increase the quality of coverage. After defining the optimization and execution objectives of the ACP module, the following results were obtained (Figure 7). To assess Wi-Fi coverage, we identified five classes of signal level quality: • Very good coverage corresponds to a signal level higher than −70 dBm. It can be noticed that the coverage is almost complete in the selected area and that the signal level varies between −90 dBm and −70 dBm. However, there are areas where the signal level is low, so there is a degradation in the coverage in these areas. This is due to the fact that the ground presents several obstacles in the direction of these locations, as is the case for some areas where the signal level is −105 dBm.
To minimize interference due to the use of adjacent channels and the use of the same channel, the AFP module from ATOLL was used. The AFP module was used to automatically calculate the total cost, which is the interference rate in the implanted network.
The optimization was performed using the ACP module, which allows the design of networks and automatically calculates the optimal parameters in terms of coverage and quality of the signal. In Table 3, we can see the proposed increases in signal quality and coverage. From Table 3, we notice that there are four modifications: a modification in the transmission power level, a modification of the azimuth level, and the deactivation of the two sites to increase the quality of coverage. After defining the optimization and execution objectives of the ACP module, the following results were obtained (Figure 7). Electronics 2021, 10, x FOR PEER REVIEW 10 of 16 Depending on the exact location of Wi-Fi users within the campus, they could connect to different access points providing different levels of signal quality. The transmitter to which the subscriber can connect is classified in descending order according to the quality of the signal that they could obtain.

Scenario Analysis
ATOLL software suggested that a minimum of five BSs are needed to provide good service coverage throughout the campus. However, we wanted to assess from the point of view of energy consumption how the number of BS will affect energy consumption. This parameter is not considered by the Wi-Fi network software optimizer.
In order to minimize energy consumption and thus GHG emissions, we developed different scenarios in which we changed the number of access points. This will help link the quality of coverage with energy consumption within the Wi-Fi network. Clearly, reducing the number of access points will reduce energy demand. Figure 8 summarizes the percentage of the total campus area covered with different signal levels for different numbers of access points. To estimate the quantity of CO2 produced, we have used the following formula: Depending on the exact location of Wi-Fi users within the campus, they could connect to different access points providing different levels of signal quality. The transmitter to which the subscriber can connect is classified in descending order according to the quality of the signal that they could obtain.

Scenario Analysis
ATOLL software suggested that a minimum of five BSs are needed to provide good service coverage throughout the campus. However, we wanted to assess from the point of view of energy consumption how the number of BS will affect energy consumption. This parameter is not considered by the Wi-Fi network software optimizer.
In order to minimize energy consumption and thus GHG emissions, we developed different scenarios in which we changed the number of access points. This will help link the quality of coverage with energy consumption within the Wi-Fi network. Clearly, reducing the number of access points will reduce energy demand. Figure 8 summarizes the percentage of the total campus area covered with different signal levels for different numbers of access points. Depending on the exact location of Wi-Fi users within the campus, they could connect to different access points providing different levels of signal quality. The transmitter to which the subscriber can connect is classified in descending order according to the quality of the signal that they could obtain.

Scenario Analysis
ATOLL software suggested that a minimum of five BSs are needed to provide good service coverage throughout the campus. However, we wanted to assess from the point of view of energy consumption how the number of BS will affect energy consumption. This parameter is not considered by the Wi-Fi network software optimizer.
In order to minimize energy consumption and thus GHG emissions, we developed different scenarios in which we changed the number of access points. This will help link the quality of coverage with energy consumption within the Wi-Fi network. Clearly, reducing the number of access points will reduce energy demand. Figure 8 summarizes the percentage of the total campus area covered with different signal levels for different numbers of access points. To estimate the quantity of CO2 produced, we have used the following formula: To estimate the quantity of CO 2 produced, we have used the following formula: (9) where Q CO 2 : amount of CO 2 (g); E ap : power consumption at each access point (kW); EI: electricity intensity (g/kWh); t OPD : duration of AP utilization (h).
Below, CO 2 emissions during the use phase are estimated for each scenario.

Scenario 1 (3 Access Points)
With three access points, we were able to cover 27% of the campus with a signal level higher than −70 dBm, and 43% of the surface is covered by a signal level between −80 dBm and −70 dBm ( Figure A3 in Appendix A).
These three access points consume 360 Wh. Based on an operating duration of 10 h, the energy consumption of electricity produced from fossil energy (natural gas) produces 150 g of CO 2 . So, if we replace the source of electricity with solar energy, we can reduce the amount of CO 2 to 19.8 g.

Scenario 2 (4 Access Points)
In the second scenario, we propose to cover the campus with four base stations. We obtained the results shown in Figure 9, where 36.4% of the campus surface is covered by an excellent level of field greater than −70 dBm, and 45% of the surface is covered by a signal level between −80 dBm and −70 dBm ( Figure A4 in Appendix A). Four access points are active at a duration of 10 h per day and consume an amount of electricity of 480 Wh. This energy consumption produces 200.64 g of CO 2 if the source of production of the electricity is based on natural gas and 26.4 g of CO 2 if the source of electricity production is solar.
where Q : amount of CO2 (g); E : power consumption at each access point (kW); EI: electricity intensity (g/kWh); t : duration of AP utilization (h).
Below, CO2 emissions during the use phase are estimated for each scenario.

Scenario 1 (3 Access Points)
With three access points, we were able to cover 27% of the campus with a signal level higher than −70 dBm, and 43% of the surface is covered by a signal level between −80 dBm and −70 dBm ( Figure A3 in Appendix A).
These three access points consume 360 Wh. Based on an operating duration of 10 h, the energy consumption of electricity produced from fossil energy (natural gas) produces 150 g of CO2. So, if we replace the source of electricity with solar energy, we can reduce the amount of CO2 to 19.8 g.

Scenario 2 (4 Access Points)
In the second scenario, we propose to cover the campus with four base stations. We obtained the results shown in Figure 9, where 36.4% of the campus surface is covered by an excellent level of field greater than −70 dBm, and 45% of the surface is covered by a signal level between −80 dBm and −70 dBm ( Figure A4 in Appendix A). Four access points are active at a duration of 10 h per day and consume an amount of electricity of 480 Wh. This energy consumption produces 200.64 g of CO2 if the source of production of the electricity is based on natural gas and 26.4 g of CO2 if the source of electricity production is solar.

Scenario 3 (5 Access Points)
In this scenario, we managed to cover 47% of the total surface with a field level higher than −70 dBm and 39.6% of the surface with a level of signals between −80 dBm and −70 dBm (Figure 8c).
The energy consumed by the five access points is equal to 600 Wh during an operating period of 10 per day. The amount of CO2 resulting from the production of electricity based on natural gas is 250.8 g and 33 g if the electricity is produced from solar energy ( Figure A4).

Scenario 4 (6 Access Points)
In this scenario, we obtained the following coverage results (Figure 8d): • 52% of the campus area is covered by a very good signal level greater than −70 dBm; • 36% of the surface is covered by a good signal level between −80 dBm and −70 dBm.

Scenario 3 (5 Access Points)
In this scenario, we managed to cover 47% of the total surface with a field level higher than −70 dBm and 39.6% of the surface with a level of signals between −80 dBm and −70 dBm (Figure 8c).
The energy consumed by the five access points is equal to 600 Wh during an operating period of 10 per day. The amount of CO 2 resulting from the production of electricity based on natural gas is 250.8 g and 33 g if the electricity is produced from solar energy ( Figure A4).

Scenario 4 (6 Access Points)
In this scenario, we obtained the following coverage results (Figure 8d): • 52% of the campus area is covered by a very good signal level greater than −70 dBm; • 36% of the surface is covered by a good signal level between −80 dBm and −70 dBm.
These access points are active for a period of 10 h per day and consume 720 wh. As a result, 418 g of CO 2 in the case where electricity is produced from natural gas and 39.6 g of CO 2 in the case where electricity is produced from solar energy. Table 4 summarizes the results obtained for the four scenarios.

GHG Mitigation of Solar-Powered Wi-Fi Deployment at ENST
In this section, we estimate the quantity of CO 2 emissions resulting from the energy consumption by the Wi-Fi network. We will use CO 2 when actually we refer to CO 2 -eq, representing the total GHG emission. We will compare the resulting carbon footprint with the quantity of CO 2 resulting if we replace the energy supply of this network with a renewable energy source. In the proposed case study, the source of energy is solar electricity. The process of evaluating the total impact is provided below. To estimate the amount of CO 2 we followed the following four steps:

•
Step 1: Identify the source of electricity for the Wi-Fi network supply.

•
Step 2: Estimate the amount of CO 2 resulting from the consumption of electricity produced from a fossil fuel source.

•
Step 3: Estimate the quantity of CO 2 reduction if the energy source is replaced by a renewable source to supply this network.

•
Step 4: Scale up and generalization We start by identifying the energy source (the source of electricity production), since the resulting quantity of CO 2 varies from one source to another. In 2015, 98.36% of the electricity produced in Algeria was from natural gas. The carbon intensity of natural gas (NG) based electricity was 418 g of CO 2 per kWh [22]. In our case, we will consider the scenario with five access points, which works for a duration of 10 h. The five access points consume 600 Wh, so the resulting quantity of CO 2 is 250 g per day and 915.42 kg per year when using NG electricity. The next step is to estimate the amount of CO 2 if the energy source is replaced by a renewable source to supply this network. Algeria is endowed with one of the highest solar radiations in the world, with more than 2500 h of sunshine on average per year over a very large part of its territory. The energy received daily on a horizontal surface of 1 m 2 is around 5 kWh, which corresponds to 1700 kWh/m 2 /year in the north and 2263 kWh/m 2 /year in the south of the country [23]. If we replace the NG electricity supply for the Wi-Fi network with solar energy, CO 2 emissions will be reduced by 217 g per day and 795 kg per year.

Forecasting the GHG Mitigation Resulting from Wider Solar-Powered Wi-Fi Deployment
Using the results of this case study, we assessed the impact of wider deployment. We developed a simple forecasting methodology for the potential GHG mitigation if solarpowered Wi-Fi is deployed at the state level. As an example, we will estimate the potential of GHG emission if solar-powered Wi-Fi is deployed throughout all university campuses in the state. For this, we need to quantify three key parameters: • Amount of GHG reduction of new technology vs. incumbent technology. In this case, solar energy is used instead of fossil energy to generate the required electricity to power the Wi-Fi network. This estimation should be performed per access point.

•
Estimation of the overall market size. This could be represented by the number of access points to cover all university campuses.

•
The potential market capture of the new technology vs. incumbent technology. Deployment cost is the main factor. Other factors (e.g., complexity of the technology deployment) may also affect this parameter.
The overall methodology to assess potential GHG mitigation when introducing a new technology is provided in Figure 9.
The first parameter is the focus of this manuscript and has been estimated in the previous paragraph. The second parameter could be obtained using the following equation: where A is the number of access points in the current case study, S Country is the total number of students in the country, and S ENST is the number of students in the current case study. Finally, market capture is probably the most difficult parameter to estimate. In the absence of a detailed quantification, we will assume an arbitrary number for this parameter. Assuming a market capture of 50%, the overall GHG mitigation through solar-powered Wi-Fi in academic campuses is about 1089 kg per day and 397,485 kg per year. Even if it is relatively small when compared to the total GHG emission in the ICT sector 720 Mt [24] or in Algeria (170 Mt in 2019) [25], wider deployment of Wi-Fi in other communities could provide additional opportunities for further GHG reductions. With increasing digitalization in multiple sectors and the wider use of video streaming, we are expecting the potential GHG reduction due to solar Wi-Fi deployment to significantly increase.
Several factors could affect this forecast. We did not account for hourly and seasonal variations of solar irradiation and load. Another critical factor is related to the potential benefit of using excess solar electricity production to address demand within and outside the campus. Indeed, in countries such as Algeria, the grid is under stress, with significant demand for electricity during hot summer days.

Conclusions
In this work, we developed a new method to link energy consumption to Wi-Fi coverage. A new GHG framework was described to quantify the potential GHG emission reduction that could result from wider Wi-Fi deployment. This framework consists of three key steps. First, a detailed model was developed to quantify the energy requirements to power a community Wi-Fi network within a university campus. Second, we estimated the GHG reduction from fuel switching between solar and fossil fuel to generate the required electricity. Finally, a simplified calculation was performed to estimate the potential GHG mitigation when a wider deployment of community Wi-Fi is achieved at the state level. This methodology could also be used to forecast GHG reductions if other clean technology solutions are deployed.

Data Availability Statement:
The data presented in this study are available on request from the corresponding author.

Acknowledgments:
This research was carried out as part of the green project, which aimed to share Canadian green technology in Algeria. This project is in partnership between the ENST campus and the Sustainable Energy Initiative Group of York University. We are grateful to the director of ENST Tahar Benabid (ENST), Rabea Cheggou (ENST), and Brahim Haroubia (ENST) for their contributions and support.

Conflicts of Interest:
The authors declare no conflict of interest. Acknowledgments: This research was carried out as part of the green project, which aimed to share Canadian green technology in Algeria. This project is in partnership between the ENST campus and the Sustainable Energy Initiative Group of York University. We are grateful to the director of ENST Tahar Benabid (ENST), Rabea Cheggou (ENST), and Brahim Haroubia (ENST) for their contributions and support.

Conflicts of Interest:
The authors declare no conflict of interest.
Appendix A    Data Availability Statement: The data presented in this study are available on request from the corresponding author.

Acknowledgments:
This research was carried out as part of the green project, which aimed to share Canadian green technology in Algeria. This project is in partnership between the ENST campus and the Sustainable Energy Initiative Group of York University. We are grateful to the director of ENST Tahar Benabid (ENST), Rabea Cheggou (ENST), and Brahim Haroubia (ENST) for their contributions and support.

Conflicts of Interest:
The authors declare no conflict of interest.
Appendix A                   Figure A6. Prediction of power level coverage in ENST campus with six base stations.