Review of Research Progress in Nontraditional Machining of Ultrahigh-Temperature Ceramic Matrix Composites

: Ultrahigh-temperature ceramic matrix composites are currently among the most promising high-temperature-resistant materials, owing to their high-temperature strength, high-toughness and excellent corrosion resistance; they are widely used in national defense and aerospace ﬁelds. However, it is a difﬁcult material to machine, and high precision is difﬁcult to achieve using traditional machining methods. Nontraditional machining methods are not constrained by material physical and mechanical properties, and good surface quality is easily obtained, which is an important direction in the ﬁeld of ultrahigh-temperature ceramic matrix composites. This paper summarizes the recent nontraditional machining methods utilized in the fabrication of ultrahigh-temperature ceramic matrix composites. Firstly, various nontraditional machining methods for ultrahigh-temperature ceramic matrix composites based on borides, carbides and nitrides are reviewed, and the machining performances under different machining conditions are compared. Subsequently, the problems and challenges of ultrahigh-temperature ceramic matrix composite nontraditional machining are summarized and discussed. Lastly, the future development path of nontraditional machining methods for ultrahigh-temperature ceramic matrix composites is summarized and predicted.


Introduction
With the rapid development of science, hypersonic missiles and reusable delivery devices have become important development directions for military aerospace and weapon systems [1].At present, the main ultrahigh-temperature materials that can be used above 2000 • C are refractory metals, C/C composites and ultrahigh-temperature ceramics.Among these, ultrahigh-temperature ceramic materials are regarded as having the greatest potential in the future ultrahigh-temperature field [2].Ultrahigh-temperature ceramic materials generally refer to a class of ceramic materials used at high temperatures above 2000 • C, mainly referring to some transition metal borides, carbides and nitrides, such as ZrB 2 , HfB 2 , TaC, ZrC, HfC and HfN [3].In addition to having a high melting point of approximately 3000 • C, they also have excellent properties, such as high hardness, high thermal conductivity, good oxidation resistance, good thermal shock resistance and a medium thermal expansion coefficient.Therefore, they are very suitable for use as high-temperature structural materials for supersonic spacecraft, and the application of ultrahigh-temperature ceramic materials in rocket engines has also attracted widespread attention [4,5].UHTCMCs are typically difficult materials to cut, and it is challenging to machine them with high precision using traditional machining methods [29].Machining the materials without compromising the characteristics of the ceramics and using machining methods that offer economical solutions while minimizing residual damage represent the main challenges in realizing the full potential of UHTCMCs.The presence of reinforcing particles makes them difficult to machine using conventional machining methods, and the surface roughness and tool wear are too great.As a result, machining costs rise; production times lengthen; and the quality of machined products declines [24].Considering the main shortcomings of its machinability, the cost of polishing the table accounts for the vast majority of the entire manufacturing cost.Additionally, traditional machining methods can create cracks and stress concentrations on the surface of UHTCMCs, which can weaken the mechanical strength of the part [30].As a result, a crucial stage in the production of UHTCMC components are identifying affordable and effective machining methods [25].The majority of conventional machining machines, such as turning, cutting, grinding and drilling, is difficult to use when machining UHTCMCs because they result in significant tool wear, excessive roughness of material surface, low material removal rate, prolonged chatter times and higher costs [31,32].For example, Satyarthi [33] performed electrical discharge machining (EDM) grinding on ceramic materials.Compared with conventional diamond grinding, the surface finish of nontraditional machining is at least three times that of low-temperature cooled conventional diamond grinding, and the material removal rate is at least four times higher.Machining appears to be impractical for the production of ceramics [26].Therefore, machining of UHTCMCs can be achieved using a variety of nontraditional methods, including chemical machining [25,27], laser machining [34][35][36][37], plasma machining [38][39][40], electron beam machining [41][42][43], electrochemical machining [44][45][46][47][48], ultrasonic machining [49][50][51][52][53] and abrasive water jet machining [54][55][56][57][58].They each have their own advantages and disadvantages.In the production of cutting blades made of cutting ceramics, some surface quality, size and shape parameters are required to provide the function of the blade (machining/cutting certain steels or alloys in a few minutes).In this case, an appropriate technology should be found to provide this quality and appropriate productivity.This review systematically summarizes the research status and development potential of nontraditional machining methods in UHTCMCs.The problems and defects in machining are pointed out.Through the influence of different machining UHTCMCs are typically difficult materials to cut, and it is challenging to machine them with high precision using traditional machining methods [29].Machining the materials without compromising the characteristics of the ceramics and using machining methods that offer economical solutions while minimizing residual damage represent the main challenges in realizing the full potential of UHTCMCs.The presence of reinforcing particles makes them difficult to machine using conventional machining methods, and the surface roughness and tool wear are too great.As a result, machining costs rise; production times lengthen; and the quality of machined products declines [24].Considering the main shortcomings of its machinability, the cost of polishing the table accounts for the vast majority of the entire manufacturing cost.Additionally, traditional machining methods can create cracks and stress concentrations on the surface of UHTCMCs, which can weaken the mechanical strength of the part [30].As a result, a crucial stage in the production of UHTCMC components are identifying affordable and effective machining methods [25].The majority of conventional machining machines, such as turning, cutting, grinding and drilling, is difficult to use when machining UHTCMCs because they result in significant tool wear, excessive roughness of material surface, low material removal rate, prolonged chatter times and higher costs [31,32].For example, Satyarthi [33] performed electrical discharge machining (EDM) grinding on ceramic materials.Compared with conventional diamond grinding, the surface finish of nontraditional machining is at least three times that of low-temperature cooled conventional diamond grinding, and the material removal rate is at least four times higher.Machining appears to be impractical for the production of ceramics [26].Therefore, machining of UHTCMCs can be achieved using a variety of nontraditional methods, including chemical machining [25,27], laser machining [34][35][36][37], plasma machining [38][39][40], electron beam machining [41][42][43], electrochemical machining [44][45][46][47][48], ultrasonic machining [49][50][51][52][53] and abrasive water jet machining [54][55][56][57][58].They each have their own advantages and disadvantages.In the production of cutting blades made of cutting ceramics, some surface quality, size and shape parameters are required to provide the function of the blade (machining/cutting certain steels or alloys in a few minutes).In this case, an appropriate technology should be found to provide this quality and appropriate productivity.This review systematically summarizes the research status and development potential of nontraditional machining methods in UHTCMCs.The problems and defects in machining are pointed out.Through the influence of different machining parameters on the performance of nontraditional machining methods, the machining characteristics and quality of UHTCMCs are analyzed, and the applicability of nontraditional machining methods is analyzed and summarized.

Material Properties of Boride-Based UHTCMCs
Ceramic matrix composites based on HfB 2 and ZrB 2 are the most common types of boride-based ceramic matrix composites.By thoughtfully choosing the composition, purity and granularity of the raw materials, the brittleness of the materials can be overcome [59].They are hard to sinter and densify due to the strength of their covalent connections.This can be resolved by increasing the diffusion rate of the material, delaying the evaporation of the material, accelerating the transmission rate of the material, encouraging the rearrangement of the particles and improving mass transfer kinetics to enhance the sintering performance and increase the density [60].Due to the formation of the liquid B 2 O 3 glass phase, which serves as a good antioxidant defense, single-phase ZrB 2 or HfB 2 exhibits good oxidation resistance below 1200 • C. B 2 O 3 rapidly evaporates above 1200 • C, decreasing its usefulness as a diffusion barrier, whereas ZrB 2 or HfB 2 quickly oxidize [61].When SiC is added, the material's oxidation resistance can be greatly increased.Glassy silicate can also develop on the material's surface at high temperatures, providing good protection below 1600 • C.
In an aspirated hypersonic cruise vehicle design, aerodynamic heating due to viscous dissipation increases with a cubic increase in velocity, which results in a stagnation temperature of about 2400 K at a cruise Mach number of 7. Due to the high L/D ratio, wave rider-derived hypersonic vehicles are used for long cruise missions in which stagnation is experienced along the entire leading edge of the wave rider [62].Thus, UHTCMCs are frequently key candidates in the hypersonic field for their ability to withstand elevated thermal and pressure loads (i.e., maintain shock under lip conditions) and maintain mechanical properties without changing the aerodynamic shape.In this family of potential materials, composites of ZrB 2 and HfB 2 -based ceramics may be the most promising (or most studied) candidates for such applications.This is primarily due to their superior high-temperature properties (mechanical and oxidation) when compared to TiB 2 and TaB 2 [63][64][65].

Electrical Discharge Machining of Boride-Based UHTCMCs
By using incredibly hot plasma channels, EDM is able to machine brittle, hard materials with complicated forms without any touch [66,67].As a result, complicated geometries can be machined using EDM for UHTCMCs [68].Some researchers have conducted experimental studies on the machining of boride-based UHTCMCs [69][70][71].
The surface quality analysis of ceramic machining is an important metric for assessing the properties and machining quality of UHTCMCs [72][73][74].For the purpose of improving the method and effectiveness of EDM, some studies have looked at the surface quality of boride-based UHTCMCs following EDM.In their study of the EDM performance of ZrB 2 -SiC and ZrB 2 -SiC-HfB 2 ceramic materials, Monteverde et al. [75] discovered that the surface of these two materials after EDM had Ra of 0.6 µm and 1 µm, respectively, and that micro-cracks and recast materials had appeared on the machined surface.After machining, shell (S), core (C) and leftover glass (G) components were discovered on the surface.Additionally, surface microcracks diminished the material's bending strength by an average of 26.4%.Using microchip-based cylindrical tool electrodes, Li et al. [76] proposed a technique for micro-EDM of ZrB 2 -SiC graphite composites.The microporous machining of ZrB 2 -SiC graphite composites was more stable with the sheet electrode and had an average machining efficiency that was 3.9 times greater than that of the cylindrical electrode.It was also found that the surface roughness decreased from Ra of 1.56 to 0.97 µm after fine drilling.In their study on the EDM performance of ZrB 2 -SiC and NbB 2 -SiC ceramic materials, Malek et al. [77] examined the machining surface and material removal rate (MRR) of several materials.The MRR calculation formula is as follows: where V is the volume of material removed (unit: mm 3 ); t 1 is the machining time (unit: min); h is machining depth; and d is the diameter of the tool electrode (unit: mm).Machined workpieces of ZrO 2 and Nb 2 O 5 were discovered by X-ray photoelectron spectroscopy (XPS) on the EDM surface, as illustrated in Figure 2a.The results showed that the oxidation of ZrB 2 -SiC and NbB 2 -SiC occurred in the EDM machine and had a significant effect on the MRR and surface quality.In order to assess the surface roughness of the structure's random region, Han et al. [78] chose a three-dimensional surface roughness measurement system and performed precision electrical machining on complex ZrB 2 -SiC structural elements.The results showed that 380 V, 3.5 A, 64 Hz for the pulse shoulder, 64 Hz for the pulse width and 3 mm/min for the maximum line speed were the optimal machining settings.The parameters of Sa, Sz and Sq's surface roughness were 6.3617, 44.4468 and 7.8314 µm, respectively.The performance of EDM is also influenced by the percentage of reinforcing particles in boride-based UHTCMCs [79,80].Saha et al. [81] examined the EDM performance of ceramic materials with SiC contents ranging from 5 to 20 wt.% in terms of MRR and surface roughness.They also investigated ZrB 2 -SiC ultrahigh-temperature ceramic EDM method.It is discovered that as the SiC concentration increases, so does the volume direct current resistivity of ZrB 2 matrix composites.As SiC increased from 5 wt.% to 20 wt.%, MRR decreased gradually, and resistivity increased steadily from 0.3 cm to 3.5 cm.The main reason was that an increase in SiC concentration reduced the electrical conductivity of ceramic materials, decreasing machining efficiency.The EDM performance of ZrB 2 -SiC ceramic matrix composites with various machining parameters for tool materials, such as titanium, tungsten, niobium, graphite and tantalum, was investigated by Sivasankar et al. [82].The results showed that, when the content of SiC was 20%, the bending strength was higher than other contents.The hardness increased when the SiC content increased, and the MRR of the workpiece increased when the SiC volume percentage increased.With the exception of tantalum, all materials yielded a superior MRR on a workpiece when the SiC percentage was 30 vol.%.Tantalum could produce a higher MRR when the workpiece contained 25% SiC.The 20 vol.% SiC workpiece has a high tool wear ratio (TWR) for all tools.ZrB 2 -B 4 C composite samples were treated using the EDM procedure by Mandal et al. [83].The findings indicate that the maximum machining speed and surface roughness occur at a B 4 C level of 25 wt.%.For 25 wt.% composite material, the B 4 C load showed the maximum hardness (20.49GPa at 1.0 kgf load).The fracture toughness values of all samples are shown in Figure 2b.Similar to the hardness, the composite showed a higher fracture toughness under a higher B 4 C load.ZrB 2 -B 4 C composite could currently be machined at a maximum speed of 10.56 mm 2 /min.ZrB 2 -B 4 C composites had an average surface roughness Ra of between 1.26 and 5.64 µm.Craters, protrusions and spherical nodules in the sealing layer of the machined surface degraded the surface's quality when the machining speed was increased.

Laser Machining of Boride-Based UHTCMCs
Laser machining is also widely used in ceramic machining; this is a wear-free method where the material is not subject to either cutting forces or vibration [32,[84][85][86].Most notably, compared to conventional and other unconventional technologies, this technique offers a faster cutting speed [87,88].Numerous researchers have carried out experimental studies to determine whether laser machining of boride-based UHTCMCs is feasible.
Analyzing the surface quality of laser machining boride-based UHTCMCs is a crucial factor in determining how well they machine [36,89].On the 2024 aluminum alloy matrix, Yang et al. [90] fabricated a ZrO2 sol-gel composite coating containing laser-ablative SiC whiskers and ZrB2 particles, as shown in Figure 3a.Under high-intensity continuous laser irradiation, the composite coating exhibits typical pitting morphology with no spalling or breaking.As shown in Figure 3b, when a 6.3 kW/cm 2 laser was used to irradiate the substrate for 10 s, the maximum backside temperature of the substrate was just 150 °C.The oxidation of ZrB2 and the ZrO2 layer produced by the ZrO2 gel can prevent the heat from the laser from transferring through the center ablative crater during laser irradiation.Additionally, the volatilization of B2O3 and the cooling effect brought on by SiO2 and ZrO2's liquid-solid phase transitions were significant factors in increasing laser ablative resistance.Ideal spiral laser surface treatment was performed by Mahmod et al. [91] on a porous ZrB2-SiC ceramic composite substrate.The following laser settings were used to create an 8 μm thick uniform glass layer: laser power of 70 W, beam diameter of 1.25 mm, speed of 2 mm/s, acceleration and deceleration rate of 1 mm 2 /s.This layer was continuous and prevented further oxidation of the bulk ceramic composite.The structure was wellpreserved, and its morphology was similar to that of the initially sintered, non-oxidized pellets.EDS analysis confirms that no oxidation occurred in the internal blocks of ZrB2-SiC due to the undetectable oxygen element.Wang et al. used three typical materials (ZrB2, ZrB2-SiC and ZrB2-SiC-G (graphite) ceramics) to systematically study the influence of defects on the bending strength of UHTCMCs [92].The results show that the sensitivity of the material to the flaw angle was in the order ZrB2-SiC > ZrB2 > ZrB2-SiC-G, as shown in Figure 3c.For the same material, a larger defect size led to greater sensitivity of strength to the angle.Reprinted/adapted with permission from Ref. [83].Copyright 2022, Elsevier.

Laser Machining of Boride-Based UHTCMCs
Laser machining is also widely used in ceramic machining; this is a wear-free method where the material is not subject to either cutting forces or vibration [32,[84][85][86].Most notably, compared to conventional and other unconventional technologies, this technique offers a faster cutting speed [87,88].Numerous researchers have carried out experimental studies to determine whether laser machining of boride-based UHTCMCs is feasible.
Analyzing the surface quality of laser machining boride-based UHTCMCs is a crucial factor in determining how well they machine [36,89].On the 2024 aluminum alloy matrix, Yang et al. [90] fabricated a ZrO 2 sol-gel composite coating containing laser-ablative SiC whiskers and ZrB 2 particles, as shown in Figure 3a.Under high-intensity continuous laser irradiation, the composite coating exhibits typical pitting morphology with no spalling or breaking.As shown in Figure 3b, when a 6.3 kW/cm 2 laser was used to irradiate the substrate for 10 s, the maximum backside temperature of the substrate was just 150 • C. The oxidation of ZrB 2 and the ZrO 2 layer produced by the ZrO 2 gel can prevent the heat from the laser from transferring through the center ablative crater during laser irradiation.Additionally, the volatilization of B 2 O 3 and the cooling effect brought on by SiO 2 and ZrO 2 's liquid-solid phase transitions were significant factors in increasing laser ablative resistance.Ideal spiral laser surface treatment was performed by Mahmod et al. [91] on a porous ZrB 2 -SiC ceramic composite substrate.The following laser settings were used to create an 8 µm thick uniform glass layer: laser power of 70 W, beam diameter of 1.25 mm, speed of 2 mm/s, acceleration and deceleration rate of 1 mm 2 /s.This layer was continuous and prevented further oxidation of the bulk ceramic composite.The structure was wellpreserved, and its morphology was similar to that of the initially sintered, non-oxidized pellets.EDS analysis confirms that no oxidation occurred in the internal blocks of ZrB 2 -SiC due to the undetectable oxygen element.Wang et al. used three typical materials (ZrB 2 , ZrB 2 -SiC and ZrB 2 -SiC-G (graphite) ceramics) to systematically study the influence of defects on the bending strength of UHTCMCs [92].The results show that the sensitivity of the material to the flaw angle was in the order ZrB 2 -SiC > ZrB 2 > ZrB 2 -SiC-G, as shown in Figure 3c.For the same material, a larger defect size led to greater sensitivity of strength to the angle.Lonné et al. [93] irradiated the porous composite ZrB2 of 39 vol.%SiC with a 90 W low-power moving laser beam under a flowing argon protective atmosphere.According to the findings, the layer thickness approached 20 μm; the temperature reached around 2500 °C; and a SiC-rich fusible phase emerged, partially dissolving ZrB2 and facilitating its sintering.Also, the surface area achieved almost complete densification.This is because the liquid phase moved toward the sample's surface and bulk after filling the pores.Rudolph et al. [94] investigated how semiconductor SiC and composite SiC-TiC-TiB2 were affected by nanosecond laser pulses in the ultraviolet spectrum and femtosecond laser pulses in the near-infrared spectrum.The findings demonstrated that Fth = 0.63 J/cm 2 was the ablation threshold of semiconductor SiC treated by a nanosecond laser pulse in the ultraviolet band.SiC-TiC-TiB2 composite ceramics have an ablation threshold of Fth = 1.38 J/cm 2 .In contrast, regardless of chemical composition, femtosecond laser pulse machining in the near infrared spectrum yielded a higher value of roughly 1.7 J/cm 2 .

Ultrasonic and Ultrasonic-Assisted Machining of Boride-Based UHTCMCs
Combining the fundamental material removal mechanism of ultrasonic machining with traditional diamond grinding, a greater MRR, increased hole precision and higher surface polish can be achieved at relatively low cost and with minimal environmental impact [95].Rotary ultrasonic machining (RUM) is a mechanical hybrid machining technique that has the potential to be utilized to treat a wide range of novel and challenging materials, such as boride-based UHTCMCs.
An in-situ combined machining technique using micro-EDM and ultrasonic milling was proposed by Li [96].In order to improve the machining efficiency and reduce the Lonné et al. [93] irradiated the porous composite ZrB 2 of 39 vol.%SiC with a 90 W low-power moving laser beam under a flowing argon protective atmosphere.According to the findings, the layer thickness approached 20 µm; the temperature reached around 2500 • C; and a SiC-rich fusible phase emerged, partially dissolving ZrB 2 and facilitating its sintering.Also, the surface area achieved almost complete densification.This is because the liquid phase moved toward the sample's surface and bulk after filling the pores.Rudolph et al. [94] investigated how semiconductor SiC and composite SiC-TiC-TiB 2 were affected by nanosecond laser pulses in the ultraviolet spectrum and femtosecond laser pulses in the near-infrared spectrum.The findings demonstrated that F th = 0.63 J/cm 2 was the ablation threshold of semiconductor SiC treated by a nanosecond laser pulse in the ultraviolet band.SiC-TiC-TiB 2 composite ceramics have an ablation threshold of F th = 1.38 J/cm 2 .In contrast, regardless of chemical composition, femtosecond laser pulse machining in the near infrared spectrum yielded a higher value of roughly 1.7 J/cm 2 .

Ultrasonic and Ultrasonic-Assisted Machining of Boride-Based UHTCMCs
Combining the fundamental material removal mechanism of ultrasonic machining with traditional diamond grinding, a greater MRR, increased hole precision and higher surface polish can be achieved at relatively low cost and with minimal environmental impact [95].Rotary ultrasonic machining (RUM) is a mechanical hybrid machining technique that has the potential to be utilized to treat a wide range of novel and challenging materials, such as boride-based UHTCMCs.
An in-situ combined machining technique using micro-EDM and ultrasonic milling was proposed by Li [96].In order to improve the machining efficiency and reduce the wear on the electrode length, two tool electrodes of different diameters can be used to fabricate the micro-nozzles.Large-diameter electrodes are used to remove large amounts of material from the inlet and outlet sections of the micro-nozzle, while small-diameter electrodes are used to manufacture the throat sections.Melting and vaporization were the major mechanisms for material loss, whereas thermal spalling was a secondary factor.The recast layer with a lot of microcracks could be successfully removed, and the surface quality could be improved, by using an ultrasonic amplitude of 2.7 µm as the machining condition for micro-cavity micro-fine ultrasonic milling with particle sizes of 10 µm and a feeding speed of 13 µm/s.Ramulu [97] performed an experimental study on the ultrasonic machining of SiC and 20 vol.% TiB 2 /SiC composites.The findings revealed that, in terms of surface roughness, the average Ra value of SiC was typically slightly higher, around 2.0 µm, while the average Ra value of composites was about 1.3 µm.The average Rz value of SiC was also higher, at about 5.4 µm, and the average Rz value of TiB 2 /SiC was 4.7 µm.

Others
In addition to the above nontraditional machining methods, other nontraditional machining methods (such as electron beam melting and plasma machining) are applied to the machining of boride-based UHTCMCs.Electron beam melting (EBM) is an established machine of powder layer-by-layer additive manufacturing metal parts.In their research of the microstructure of produced materials under various machining circumstances, Jia et al. [98] aimed to assess the viability of EBM for the production of boride-based UHTCMCs.Based on the EBM approach, a mathematical model of ZrB 2 -30 vol.%ZrSi 2 was fabricated, and the machining parameters were then simulated and optimized.The findings indicated that the best machine parameters for the fabrication of ZrB 2 -30 vol.%ZrSi 2 composites using the EBM technique were 500 W beam power at scanning speeds of 500 mm/s and 1000 W beam power at 1000 mm/s.Pasagada et al. [99] discovered that it was possible to fabricate ZrB 2 -based ultrahightemperature ceramics components by liquid phase sintering using the EBM method.It has been found that the needle-shaped patterns were produced by melting and solidification change, depending on the input energy density.The impact of the quantity of Ti added on the microstructure growth and phase evolution of ZrB 2 -SiC ceramic composites during discharge plasma sintering was investigated by Ghasali et al. [100].By using high-energy ball milling and spark plasma sintering at 50 MPa pressure for 7 min, ZrB 2 -20 vol.%SiC samples with a Ti content of 15 wt.% were fabricated.During the sintering machine, the Ti additive was totally consumed and transformed into the ceramic components TiC, TiB and TiSi 2 .A further refractory ZrC phase was found as a result of the lateral interaction between ZrB 2 and the SiC and Ti additions.Four components of ZrB 2 -SiC-ZrC-C f UHTCMC were made by Adibpur et al. [101] using a discharge plasma sintering technique.The findings indicated that the greatest characteristics were found in 5% ZrC and 2.5% Cf composites, with a relative density of 99.6%, a hardness of 18 GPa and a bending strength of 565 MPa.

Summary
In this section, the classification and properties of boride-based UHTCMCs are introduced in detail, and various special machining methods applied to boride-based UHTCMCs are described, including EDM, laser machining, ultrasonic and ultrasonic assisted machining, and other special machining technologies.The machining effects of various methods are described in terms of surface quality, precision, machining cost, etc. applied and obtained.Table 1 depicts the machining effect and application of special machining to boride-based UHTCMCs.However, these technologies cannot simultaneously achieve economical, stable and non-destructive machining of boride-based UHTCMCs.As the preparation of new boride-based UHTCMCs will develop toward homogenization, low porosity and more stable physical and chemical properties [102,103], better nontraditional machining methods need to be developed.The presence of transition metal oxides in the heat affected zone has significant influence on the surface quality and removal efficiency of the materials.
It can perform precision micro-or mirror-EDM as well as complex structure machining.
It is necessary to clarify the precise ZrB 2 -SiC machining mechanism.
Saha [81], 2014 ZrB 2 -SiC The bending strength and tantalum MRR were highest on the workpiece, with a SiC content of 25% by volume.
The EDM performance of ZrB2-SiC composites is investigated.
The composition with 25 wt.%B4C has the highest machining speed, a dense structure and superior physical and mechanical qualities.
Mandal [83], 2022 Laser machining ZrO 2 sol-gel composite coating When the power density was 6.3 kW/cm 2 , the maximum back surface temperature of the coating was only 150 It offers a substitute for the oxidation machine that occurs in ceramic materials.
Future reliability assessments of brittle structures and the design of high-strength brittle materials will greatly benefit from this.
Wang [92], 2020 ZrB 2 -39 mol.%SiC Using a 90 W laser, a dense crust with a thickness of more than 20 µm was obtained on a surface area of 0.36 cm 2 in less than 2 min.
This work confirms the feasibility of laser surface densification of porous ZrB 2 -SiC pieces.
Determined by threshold flows and morphology.Singh [94] The radial and axial machining errors of the 400 µm electrode were less than 16 µm and 17 µm, respectively, and the machining efficiency was 1.6 times higher than that when using a small electrode.
It is possible to realize highprecision combined machining of micro-three-dimensional structures.
Li [96], 2018 SiC and TiB 2 /SiC The average Ra of TiB 2 /SiC composites was 3.7 to 5. 90   Ceramic matrix composites based on ZrC, HfC, TaC, TiC and other carbides make up the majority of carbide-based UHTCMCs.These compounds have a higher melting point than borides and do not change from a solid phase during heating.They maintain high strength at high temperatures and exhibit good thermal shock resistance [104].However, this type of carbide ceramic also has very low oxidation resistance and fracture toughness.To overcome the brittleness of ceramics, fiber is usually used to strengthen and toughen them [105,106].
Theoretically, carbide-based UHTCMCs have excellent high temperature resistance, low density, high specific strength and modulus, oxidation resistance, ablative resistance [6,107] and other properties.Carbide-based UHTCMCs have the potential to replace metal as a high-temperature structural material [1].However, the high-temperature mechanical properties and machining properties conferred on carbide-based UHTCMCs in the current mass production machine are insufficient to meet all of the requirements of aerospace structural parts in extreme environments or long-term use [108,109].The high-temperature mechanical properties of carbide-based UHTCMCs used in aircraft structural parts are mainly reflected in toughness, high-temperature stability (hightemperature oxidation resistance) and wear resistance.High-toughness is required to withstand high impact, bending and tensile forces during high temperature and high speed operation [110].High-temperature stability is critical for long-term use in hot environments [104].In addition, many aircraft structures are subjected to high-speed friction between air and other objects [111].This requires better wear resistance.Equally important machining properties are related to whether carbide-based UHTCMCs components can achieve the high temperature mechanical properties, mass production and durability required for aircraft [29].

Electrical Discharge Machining of Carbide-Based UHTCMCs
The study of the relationship between machine parameters and machining performance is an important link to optimize the EDM technology of cemented carbide UHTCMCs [112][113][114].Gwon et al. [112] investigated the effect of capacitance and voltage on the conductive SiC-Ti 2 CN composite during micro-discharge drilling, as well as the inlet clearance, machining time, short circuit number, MRR, count and other variables.According to the experimental findings, SiC-Ti 2 CN had a higher feed clearance at 2 µm/s than it did at 1 µm/s.The secondary discharge accounted for the increased inlet clearance of SiC-Ti 2 CN at a feed rate of 2 µm/s.There were essentially no short circuits when the capacitance was 1500 pF or 2000 pF, and the feed rate was 1 µm/s.The EDM performance of Al 2 O 3 /SiC w /TiC ceramic composites was explored by Patel et al. [73] and optimized by using the response surface method (RSM).The discharge current was set to 3 A; the pulse width as 10 µs; and the duty cycle as 0.88 to produce the best machining performance.Ra was measured at 1.05 µm under ideal machining conditions, but when discharge current increased, Ra rapidly worsened and then gradually fell after the peaking value.The established model could reliably predict surface roughness within the 95% confidence interval.Al-SiC-B 4 C composites were cut using the EDM process by Kumar et al. [115] to study the effects of different machining parameters on the slit width and cutting speed during EDM.The statistical significance test was carried out after the mathematical model, and the results were compatible with the findings of the experiment.According to RSM, the ideal machining settings were as follows: 20 A current, 108.6 µs pulse width, 10 mm/min wire feeding speed and 5.65% B 4 C content.Metal carbide is vulnerable to electrical erosion, and the mechanism of electrical erosion is not yet clear.The challenge for EDM in carbide-based UHTCMCs is to adapt the machine to make electrical corrosion more controllable.

Laser Machining of Carbide-Based UHTCMCs
The numerical model analysis of laser machining carbide-based UHTCMCs can improve the machining parameters more efficiently [116,117].Xia [118] studied a nanosecond pulsed laser-induced controlled oxidation-micro-milling coupling method to enhance the micromachining performance of carbide-based UHTCMCs.According to Figure 4a,b, a three-dimensional finite element model was built using the ABAQUS program.The effect of laser machining parameters and auxiliary gases on the oxidation behavior of TiB 2 -TiC ceramic composites was investigated, and the effect of laser parameters on temperature field distribution was simulated.The outcomes demonstrated that a strong laser flux would vaporize the oxide and cause the cast layer to develop.When the laser fluence was 10.78 J/cm 2 and the laser scanning speed was 1 mm/s, the irradiated surface had a better oxidation effect, and the subsequent micro-milling machine had a better oxidation effect and a higher MRR.Under the optimal laser parameters, the porous oxide layer was formed, and the thickness of the oxide layer and the oxide layer reached 63 and 22 µm, respectively.In addition, the hardness of the sublayer was much lower than that of the substrate.

Laser Machining of Carbide-Based UHTCMCs
The numerical model analysis of laser machining carbide-based UHTCMCs can improve the machining parameters more efficiently [116,117].Xia [118] studied a nanosecond pulsed laser-induced controlled oxidation-micro-milling coupling method to enhance the micromachining performance of carbide-based UHTCMCs.According to Figure 4a,b, a three-dimensional finite element model was built using the ABAQUS program.The effect of laser machining parameters and auxiliary gases on the oxidation behavior of TiB2-TiC ceramic composites was investigated, and the effect of laser parameters on temperature field distribution was simulated.The outcomes demonstrated that a strong laser flux would vaporize the oxide and cause the cast layer to develop.When the laser fluence was 10.78 J/cm 2 and the laser scanning speed was 1 mm/s, the irradiated surface had a better oxidation effect, and the subsequent micro-milling machine had a better oxidation effect and a higher MRR.Under the optimal laser parameters, the porous oxide layer was formed, and the thickness of the oxide layer and the oxide layer reached 63 and 22 μm, respectively.In addition, the hardness of the sublayer was much lower than that of the substrate.Al2O3-34 wt.% TiC ceramics, which are increasingly employed in high-precision parts as head sliders, have been machined using laser micromachining by Oliveira et al. [119].The findings demonstrated a relationship between variations in surface morphology, roughness and clearance rate.Additionally, under laser irradiation, solid solutions of TiC and Al2O3 were transformed into TiO2, TiC0.7N0.3 and Al-Ti.On Si3N4/TiC ceramic surface by Xing et al. [120], who created two types of regular micro-groove patterns with various geometric properties using a Nd:YAG laser.Friction and wear tests were used to examine the tribological properties of these textured ceramics with and without MoS2 Al 2 O 3 -34 wt.% TiC ceramics, which are increasingly employed in high-precision parts as head sliders, have been machined using laser micromachining by Oliveira et al. [119].The findings demonstrated a relationship between variations in surface morphology, roughness and clearance rate.Additionally, under laser irradiation, solid solutions of TiC and Al 2 O 3 were transformed into TiO 2 , TiC 0.7 N 0.3 and Al-Ti.On Si 3 N 4 /TiC ceramic surface by Xing et al. [120], who created two types of regular micro-groove patterns with various geometric properties using a Nd:YAG laser.Friction and wear tests were used to examine the tribological properties of these textured ceramics with and without MoS 2 lubrication.In all experiments, the friction coefficient of the textured ceramics was lower than that Coatings 2023, 13, 187 13 of 27 of the smooth ceramics.The wavy grooves among the examined patterns had the best anti-friction effect, and MoS 2 lubrication could extend the wear life of the textured ceramics.By using an oxygen-acetylene torch and high-intensity laser irradiation, Feng et al. [121] assessed the ablative characteristics of ZrC-SiC coatings.The coating had linear and mass ablative rates of -0.37 µm/s and -0.09 mg/s, respectively, and could shield carbon/carbon composites from abrasion for 600 s under oxyacetylene conditions.As shown in Figure 5, the original powder inevitably reacts with oxygen during the spraying machine, and continuous ablation forms a white oxide layer on the entire surface of the sample.However, no obvious defects appear until the ablation time is extended to 600 s, indicating that it has good ablative resistance.
lubrication.In all experiments, the friction coefficient of the textured ceramics was lower than that of the smooth ceramics.The wavy grooves among the examined patterns had the best anti-friction effect, and MoS2 lubrication could extend the wear life of the textured ceramics.By using an oxygen-acetylene torch and high-intensity laser irradiation, Feng et al. [121] assessed the ablative characteristics of ZrC-SiC coatings.The coating had linear and mass ablative rates of -0.37 μm/s and -0.09 mg/s, respectively, and could shield carbon/carbon composites from abrasion for 600 s under oxyacetylene conditions.As shown in Figure 5, the original powder inevitably reacts with oxygen during the spraying machine, and continuous ablation forms a white oxide layer on the entire surface of the sample.However, no obvious defects appear until the ablation time is extended to 600 s, indicating that it has good ablative resistance.

Ion Beam Machining of Carbide-Based UHTCMCs
Ion beam machining (IBM) can efficiently machine carbide-based UHTCMCs [122,123].With an energy density greater than 10 J/cm 2 , Uglov et al. [124] investigated the effects of high-energy pulsed ion beam (HPIB) and compressed plasma flux (CPF) treatment on the phase, element composition, microstructure, hardness and depth of the modified layer of WC-TiC-CO cemented carbide.The findings demonstrate that the fusion of tungsten carbide and titanium carbide particles to generate a tungsten saturated (W1-xTix)C solid solution occurs as the energy density increases in short pulse HPIB.The shock wave produced by the high-power pulse leads to the creation of many cracks in the carbide particles inside and below the melting layer.The melt layer formed through convective mixing of the melt components when the CPF pulse length of 13 to 40 J/cm 2 was prolonged (up to 100 μs) and the thickness of the melt layer was 8 to 10 μm (40 J/cm 2 ).Two times as hard as untreated cemented carbide, the surface containing a saturated (W1-xTix)C solid solution had a thickness of several microns.Wolfe et al. [125] used ion beam assisted and electron beam physical vapor deposition to fabricate multilayered TiB2/TiC coatings with varying total layers (2-20) on WC-6 wt.% Co and 0.3 wt.% TaC substrates.As shown in Figure 6a, the results indicated that the average Vickers hardness value increased as the number of layers increased.In addition, the adhesion of the multilayer film with a thickness of 4 μm was higher than 50 N.Wang et al. [126] used an ion beam assisted deposition system to prepare nanoscale TiC/Mo multilayers with a modulated wavelength range from 2.5 to 13.7 nm at a temperature close to ambient.Using nanoindentation method, the multilayer's hardness and elastic modulus were investigated.The findings indicated that the multilayer hardness was greater than the regular mixing value and the maximum hardness, which was almost twice the regular mixing value at 21.40 GPa at = 2.5 nm, as shown in Figure 6b,c.Multilayers also confirmed a dependence on the

Ion Beam Machining of Carbide-Based UHTCMCs
Ion beam machining (IBM) can efficiently machine carbide-based UHTCMCs [122,123].With an energy density greater than 10 J/cm 2 , Uglov et al. [124] investigated the effects of high-energy pulsed ion beam (HPIB) and compressed plasma flux (CPF) treatment on the phase, element composition, microstructure, hardness and depth of the modified layer of WC-TiC-CO cemented carbide.The findings demonstrate that the fusion of tungsten carbide and titanium carbide particles to generate a tungsten saturated (W 1-x Ti x )C solid solution occurs as the energy density increases in short pulse HPIB.The shock wave produced by the high-power pulse leads to the creation of many cracks in the carbide particles inside and below the melting layer.The melt layer formed through convective mixing of the melt components when the CPF pulse length of 13 to 40 J/cm 2 was prolonged (up to 100 µs) and the thickness of the melt layer was 8 to 10 µm (40 J/cm 2 ).Two times as hard as untreated cemented carbide, the surface containing a saturated (W1-xTix)C solid solution had a thickness of several microns.Wolfe et al. [125] used ion beam assisted and electron beam physical vapor deposition to fabricate multilayered TiB 2 /TiC coatings with varying total layers (2-20) on WC-6 wt.% Co and 0.3 wt.% TaC substrates.As shown in Figure 6a, the results indicated that the average Vickers hardness value increased as the number of layers increased.In addition, the adhesion of the multilayer film with a thickness of 4 µm was higher than 50 N.Wang et al. [126] used an ion beam assisted deposition system to prepare nanoscale TiC/Mo multilayers with a modulated wavelength range from 2.5 to 13.7 nm at a temperature close to ambient.Using nanoindentation method, the multilayer's hardness and elastic modulus were investigated.The findings indicated that the multilayer hardness was greater than the regular mixing value and the maximum hardness, which was almost twice the regular mixing value at 21.40 GPa at = 2.5 nm, as shown in Figure 6b,c.Multilayers also confirmed a dependence on the arrangement of individual layer thicknesses.Multilayers were harder than their hard components after taking individual thickness characteristics (TiC) into account.
arrangement of individual layer thicknesses.Multilayers were harder than their hard components after taking individual thickness characteristics (TiC) into account.

Others
In addition to the several nontraditional machining methods mentioned above, other nontraditional machining methods (such as electron beam machining and water jet machining) are used to machine carbide-based UHTCMCs.Gao et al. [127] used electron beam melting to fabricate a consistent TiAl matrix structure of dispersed carbides by using a semi-melting stage in the fabrication of TiC/high-Nb-TiAl nanocomposites.Most TiC nanoparticles dissolved during the EBM melting machine, and Ti2AlC was almost spherical, rod-like particles.Carbides had an impact on the TiAl matrix's microstructure deterioration and solidification behavior.Oh et al. [128] investigated the link between the microstructure of (TiC, SiC) yTi-6Al-4V surface composites exposed to high-energy electron beams and their hardness and fracture toughness.On a Ti-6Al-4V substrate, a mixture of TiC, SiC or TiC-SiC powder and CaF2 flux was added.Using an electron beam accelerator, these mixtures were then exposed to an electron beam.Martensite matrix contained a significant number of precipitates (up to 66 vol.%), including TiC and Ti-Si, and formed a surface composite layer that was 1.2-2.1 mm thick.Hard ceramics could be effectively cut and formed using abrasive water jet machining.Al/TiC composites were subjected to abrasive water jet machining by Kiran et al. [129] in order to investigate the impact of various parameters on material removal and surface roughness.The outcomes demonstrated that the MRR and surface roughness were ideal at 2.024 mm 3 /min and 2.832 μm, respectively; when the distance was 9 mm, the moving speed was 165 mm/min, and the TiC was 0.9 wt.%.

Summary
The classification and properties of carbide-based UHTCMCs were described, and various nontraditional machining methods applied to carbide-based UHTCMCs were reviewed, including EDM, laser machining, ion beam machining and other nontraditional machining methods.The machining effect and application of carbide-based UHTCMCs are nontraditional machining shown in Table 2.Because the ceramic matrix of carbidebased UHTCMCs has poor conductivity, the efficiency of electric discharge machining is low.Electrode vibration and deep washing can improve the performance of EDM to a certain extent.The EDM method for machining carbide-based UHTCMCs-such as removal mechanism, molding and machine parameter optimization-still needs to be

Others
In addition to the several nontraditional machining methods mentioned above, other nontraditional machining methods (such as electron beam machining and water jet machining) are used to machine carbide-based UHTCMCs.Gao et al. [127] used electron beam melting to fabricate a consistent TiAl matrix structure of dispersed carbides by using a semi-melting stage in the fabrication of TiC/high-Nb-TiAl nanocomposites.Most TiC nanoparticles dissolved during the EBM melting machine, and Ti 2 AlC was almost spherical, rod-like particles.Carbides had an impact on the TiAl matrix's microstructure deterioration and solidification behavior.Oh et al. [128] investigated the link between the microstructure of (TiC, SiC) yTi-6Al-4V surface composites exposed to high-energy electron beams and their hardness and fracture toughness.On a Ti-6Al-4V substrate, a mixture of TiC, SiC or TiC-SiC powder and CaF 2 flux was added.Using an electron beam accelerator, these mixtures were then exposed to an electron beam.Martensite matrix contained a significant number of precipitates (up to 66 vol.%), including TiC and Ti-Si, and formed a surface composite layer that was 1.2-2.1 mm thick.Hard ceramics could be effectively cut and formed using abrasive water jet machining.Al/TiC composites were subjected to abrasive water jet machining by Kiran et al. [129] in order to investigate the impact of various parameters on material removal and surface roughness.The outcomes demonstrated that the MRR and surface roughness were ideal at 2.024 mm 3 /min and 2.832 µm, respectively; when the distance was 9 mm, the moving speed was 165 mm/min, and the TiC was 0.9 wt.%.

Summary
The classification and properties of carbide-based UHTCMCs were described, and various nontraditional machining methods applied to carbide-based UHTCMCs were reviewed, including EDM, laser machining, ion beam machining and other nontraditional machining methods.The machining effect and application of carbide-based UHTCMCs are nontraditional machining shown in Table 2.Because the ceramic matrix of carbidebased UHTCMCs has poor conductivity, the efficiency of electric discharge machining is low.Electrode vibration and deep washing can improve the performance of EDM to a certain extent.The EDM method for machining carbide-based UHTCMCs-such as removal mechanism, molding and machine parameter optimization-still needs to be further studied.The laser machining method can significantly reduce the formation of the oxide layer, and water jet-assisted laser machining can obtain a higher surface quality; however, its cost is high; its precision control is poor; and its machining methods need to be further studied.In addition, it is necessary to further study the machining mechanism by establishing analytical or numerical models [130][131][132].The MRR of SiC-Ti 2 CN and SUS304 converged to about 44,000 µm 3 /s and 23,700 µm 3 /s, respectively, when the unit discharge energy was high.
Study on micro-EDM properties of novel conductive SiC-Ti 2 CN composite.
This technique is useful for figuring out the best parameter settings for EDM ceramic composites.
Patel [73], 2009 ZrB 2 -SiC and NbB 2 -SiC The optimum machining conditions were as follows: the current of 20 A, pulse switching time of 108.6 µs, wire feeding speed of 10 mm/min, and B 4 C content in the composite of 5.65%.
Machinability prediction model Kumar [115], 2022 Laser machining TiB 2 -TiC Under a laser flux of 10.78 J/cm 2 and a scanning speed of 1 mm/s, the hardness of the sublayer was 9.6 ± 0.7 GPa, which was far lower than the hardness of 20 ± 0.7 GPa.

It offers a theoretical foundation
for the upcoming fine milling.Xia [118], 2022 Al 2 O 3 -34 wt.% TiC The limit roughness increases from 0.12 to 0.65 mm as the flux increases from 2 to 8 J/cm 2 .
Laser micromachining Al 2 O 3 -34 wt.%TiC ceramics is proven to be feasible.
On Si 3 N 4 ceramics, the use of laser surface texturing is discussed.

ZrC-SiC
The linear and mass ablation rates of the coating were −0.37 µm/s and −0.09 mg/s, respectively.
Scale evolution of multilayer coatings is discussed in depth.

WcTiC-Co
The CPF pulse lasted longer when the energy density was 13~40 J/cm 2 .
HPI and CPF are successfully used to improve the mechanical properties and wear resistance of WcTiC-Co.
The effect of the total number of TiB coatings on its properties is discussed using various characterization methods.
The possible mechanism of hardening is discussed.
The behavior of solidification and subsequent microstructure degradation are influenced by particles.
It is expected to serve as the basic data for the selection and application of composite materials.
Study on water jet machining properties of Al/Tic composites.

Material Properties of Nitride-Based UHTCMCs
The matrix of nitride-based UHTCMCs is primarily composed of nitrogen and excess metals (such as titanium, vanadium, niobium, zirconium, tantalum and hafnium), as well as nitride ceramics with aluminum and oxygen in solid solution in silicon nitride while retaining the structure of silicon nitride [133], e.g., ceramics made of silicon nitride, aluminum nitride, boron nitride, etc.
Today, nitride-based UHTCMCs can be seen as a class of materials comparable to steel.Therefore, nitride-based UHTCMCs are prime candidates for a variety of hightemperature applications, such as rotor and stator blades for advanced gas turbines, valves and CAM roller followers for gasoline and diesel engines [134].On the other hand, the most significant milestone was the use of silicon nitride UHTCMCs as a thermal node component produced by AlliedSignal for aircraft and industrial auxiliary turbine power units, as well as various components used in aircraft turbine engines [135], and as a valve for automotive diesel engines selected by Daimler-Benz.Because of this, producing complex shapes using conventional machining methods is very challenging and expensive, and it can result in cracks on the machined surface [29,136].

Electrical Discharge Machining of Nitride-Based UHTCMCs
Nitride-based UHTCMCs have been verified to be capable of machining with EDM [137,138].Using the Taguchi L25 orthogonal test, Selvarajan et al. [139] investigated the EDM characteristics of Si 3 N 4 -TiN intermetallic compounds and ceramic composites.The machine parameters, including current, pulse opening and closing times, spark gap voltage and dielectric pressure, were optimized by taking into account the measured response.Gray correlation analysis was used to calculate the ideal performance characteristics.The measurements were as follows: spark gap voltage = 40 V; dielectric pressure = 18 kg/cm 2 ; current = 7 A; pulse off time = 9 µs; and pulse on time = 7 µs.ATZ (ZrO 2 Al 2 O 3 ) and Si 3 N 4 -TiN are two different ceramic composites whose ablative behavior was examined by Schubert et al. [140].Experiments were conducted to evaluate the highest aspect ratio of the micro-hole that could be produced, the surface quality that resulted and the viability of machining intricate 3D structures by EDM.The findings demonstrated that in order to get a high MRR, a certain set of parameters must be established because the material properties of ceramic composites are strongly dependent on their mixing ratio.As a result, the ideal parameter range for oxide ceramics, such as ATZ, was found to be between 40 and 60 µJ, whereas for non-oxide ceramics, such as Si 3 N 4 -TiN, the ideal parameter range was between 100 and 110 µJ, as shown in Figure 7. Si 3 N 4 -TiN exhibits unique ablative behavior, with an MRR of 200% compared to ATZ, as a result of the breakdown of Si 3 N 4 -TiN at high temperatures in the discharge zone.In their investigation of the impact of micro-EDM milling performance on Si 3 N 4 -TiN workpieces, Marrocco et al. [141] examined MRR and TWR in relation to discharge pulse types to assess how various pulse forms affected the performance indices of such micro-EDM.Analysis revealed that MRR was solely responsive to normal pulses for the set of machine parameters taken into account, with other pulse types having no discernible impact.However, the presence of arcing and delayed pulses resulted in an unanticipated improvement in tool wear, whereas the TWR was adversely affected by regular pulses.The surface of the Si 3 N 4 -TiN micro-EDM was examined using SEM and EDS, and it was discovered that there were resolidified droplets and microcracks, which altered the chemical composition and surface quality of the ensuing micro-machining features.Bucciotti et al. [142] investigated and assessed the EDM machining method while researching the microstructure, mechanical characteristics and toxicological characteristics of Si 3 N 4 -TiN ceramic composites.Si 3 N 4 -TiN's mechanical and microstructural characteristics demonstrated that it had the potential to function as a biomaterial that could replace load-bearing prostheses.The development of Si 3 N 4 -TiN as a biomaterial and the use of EDM to create devices with a near-net shape were thus encouraged.TiN's mechanical and microstructural characteristics demonstrated that it had the potential to function as a biomaterial that could replace load-bearing prostheses.The development of Si3N4-TiN as a biomaterial and the use of EDM to create devices with a near-net shape were thus encouraged.
Figure 7. Surface quality analysis and electron microscopy of ATZ and Si3N4-TiN before and after machining.Reprinted/adapted with permission from Ref. [140].Copyright 2016, Elsevier.

Laser Machining of Nitride-Based UHTCMCs
In recent years, lasers have been widely used in nitride-based UHTCMCs machining [143][144][145][146]. TiN/Si3N4 was machined using a Nd:YAG laser by Campbell and Islam [147], who also examined the rate of material removal, the surface roughness and the likelihood of microcracks.The findings demonstrated that TiN/Si3N4 had a MRR as high as 110 mm 3 /min.The surface roughness was impacted by the pulse energy.The lower the energy, Figure 7. Surface quality analysis and electron microscopy of ATZ and Si 3 N 4 -TiN before and after machining.Reprinted/adapted with permission from Ref. [140].Copyright 2016, Elsevier.

Laser Machining of Nitride-Based UHTCMCs
In recent years, lasers have been widely used in nitride-based UHTCMCs machining [143][144][145][146]. TiN/Si 3 N 4 was machined using a Nd:YAG laser by Campbell and Islam [147], who also examined the rate of material removal, the surface roughness and the likelihood of microcracks.The findings demonstrated that TiN/Si 3 N 4 had a MRR as high as 110 mm 3 /min.The surface roughness was impacted by the pulse energy.The lower the energy, the smoother the surface.In the range between 0.8 and 1.0 J/pulse, the average surface roughness was 0.81 µm.The effectiveness of material removal was unaffected by plasma production, even when the overlapped pulse frequency was as high as 75%.On ceramic composites made of Si 3 N 4 and TiC, Vlasova et al. [148] performed laser ablation research.The findings demonstrated that Si 3 N 4 /TiC would break down when exposed to laser light, and these compounds would also split into Si, Ti and N 2 .The byproducts of laser-induced ablation was deposited as composite glass (amorphous) sheets after being oxidized to SiO 2 and TiO 2 as they traveled through the atmosphere containing O 2 + N 2 .TiSi 2 , which participated in the ablation machine and absorbed Ti, Al and Y atoms/oxides in the film, was partially formed by the Y 2 O 3 and Al 2 O 3 impurities in the laser ablation ceramics.In order to create a sequence of linear parallel micro-grooves on the surface of the samples, Tshabalala et al. [144] treated Si 3 N 4 -SiC composite samples using a nanosecond Nd:YAG laser system under various laser energy (0.1~0.6 mJ) and lateral pulse overlap (50%~88%).The findings demonstrated that when pulse energy and transverse overlap increased, material removal increased logarithmically.The ideal surface texture was attained at a combination of 0.3 mJ (2.38 × 105 J/m 2 ) and 50% pulse energy, and transverse pulse overlap, as illustrated in Figure 8.The material removal threshold was set at 0.1 mJ (0.78 × 105 J/m 2 ).In order to create a high-quality microchannel bionic texture on a Si3N4/TiC ce surface, Xing et al. [149] investigated the effects of nanosecond laser machine param with a wavelength of 1064 nm on the surface quality and geometry of microchanne findings demonstrated that the laser machine settings had a significant impact on t crochannel's surface morphology and geometry.Larger channel depth and width Reprinted/adapted with permission from Ref. [144].Copyright 2016, Elsevier.
In order to create a high-quality microchannel bionic texture on a Si 3 N 4 /TiC ceramic surface, Xing et al. [149] investigated the effects of nanosecond laser machine parameters with a wavelength of 1064 nm on the surface quality and geometry of microchannels.The findings demonstrated that the laser machine settings had a significant impact on the microchannel's surface morphology and geometry.Larger channel depth and width were often produced by increased laser power, slower scanning speeds, higher frequencies and higher sweep frequencies due to more energy accumulation.For microchannel machining, laser machine parameters of 10 W of power, 20 kHz of frequency and 50 mm/s of scanning speed were ideal.Xing et al. [150] used a femtosecond pulsed laser with a pulse width of 120 fs, a wavelength of 800 nm and a repetition frequency of 1000 Hz to create several parallel nanoscale grooves on the surface of Si 3 N 4 /TiC ceramics.The ideal values were 2.5 µJ pulse energy, 130 µm/s of speed and a single-pass.Increases in pulse energy and decreases in scanning speed result in deeper grooves.Surface roughness rose as pulse energy, scanning speed and scanning times increased.

Ion Beam Machining of Nitride-Based UHTCMCs
Using a dual ion beam technique, Colligon et al. [151] produced hard nanocomposite TiN/Si 3 N 4 coatings on Si.An analysis of the coating's cross-section, using high-resolution transmission electron microscopy, revealed that the ion-assisted microstructure transforms from an unaided columnar structure to the presence of tiny crystals in the amorphous seepage network.When ion-assisted energy was increased for Si substrates that were not heated, microhardness values rose from 24 to 29 GPa, whereas for substrates that were deposited at 400 • C, microhardness values were 7 to 8 GPa or higher.The coatings' microhardness values remained unchanged even after annealing at 1000 • C, demonstrating their remarkable thermal stability.Direct ion lithography and a Ga-focused ion beam were utilized by Mitrofanov et al. [152] to illustrate the feasibility of creating a submicron window in the Si 3 N 4 /GaN shield.The Si 3 N 4 mask after Ga-focused ion beam etching had good quality and no imperfections according to a substrate surface analysis.SEM pictures showing the creation of fringed surfaces provided further evidence of the selective growth materials' high crystal quality.

Summary
In this section, nitride-based UHTCMCs are introduced in terms of composition, properties and limitations of traditional machining.A variety of nontraditional machining methods for nitride-based UHTCMCs, including EDM, laser machining and ion beam machining, are summarized.The optimization of electrical parameters in EDM can improve the machining quality, and the optimization of laser machine parameters can obtain the best surface texture of nitride-based UHTCMCs microchannels.The machining effects and applications of nontraditional machining of nitride-based UHTCMCs are shown in Table 3.In comparison to boride-and carbide-based UHTCMCs, relatively little research has been conducted on nontraditional machining of nitride-based UHTCMCs.The best performance parameters resulted in a current of 7 A, a pulse opening time of 7 µs, a pulse closing time of 9 µs, a dielectric pressure of 18 kg/cm 2 and a spark gap voltage of 40 V.This method can effectively improve the spark corrosion machine.
Selvarajan [139], 2016 ATZ and Si 3 N 4 -TiN The range of the optimization parameter set was found to be between 40 and 60 µJ for ATZ and between 100 and 110 µJ for Si 3 N 4 -TiN.
It encouraged using Si The microhardness values for the substrate that was deposited at 400 • C were 7-8 GPa or higher.
These coatings are highly thermally stable.
Colligon [151], 2005 Si 3 N 4 /GaN After FIB etching, the etching depth of the material was 6-7 nm, and the average Ra was 0.53 nm.
The obtained results can be used for the prototyping of submicron photonic and electronic structures.

Discussions
UHTCMCs are widely used in aerospace, automobiles, manufacturing and other fields due to their high wear resistance, corrosion resistance and low density.However, the performance of UHTCMCs can be negatively impacted by material surface and subsurface degradation, such as microcracks, during machining.Ceramic engineering enhances the method for machining materials but degrades their mechanical qualities.Traditional machining of UHTCMCs has drawbacks such as significant tool wear and inevitable machining flaws.Most research focuses on the removal mechanism of UHTCMCs, parameter optimization and tool selection.To reduce machining defects, the traditional machining methods for UHTCMCs need to be further optimized.This includes developing new tool structures and optimizing machine parameters.Table 4 shows a relative comparison of different machining methods [30].
(1) Figure 9 compares the machining efficiency, machining accuracy, machining cost and environmental impact of different nontraditional machining methods of UHTCMCs.Compared with other machining methods, the EDM machine is a green machining method with less pollution and a low cost.It has the potential to prepare surfaces with excellent antifouling properties [153].EDM is frequently used to machine UHTCMCs because it is not constrained by the workpiece's hardness, tensile strength, toughness or other mechanical qualities [154].At the same time, the EDM of UHTCMCs has a high material removal rate.For example, Si 3 N 4 -TiN exhibits a unique ablation behavior during EDM, and the MRR is 200% compared with ATZ [140].However, selecting an auxiliary electrode that is appropriate for a specific industrial application for a variety of UHTC-EDM machining is complicated and difficult because many different factors must be considered, such as the properties of the ceramic material, the size and formation of acoustic emissions, the machining performance indices and many others.This requires extensive numerical and experimental studies on establishing a machine database of different UHTCMCs [155].(2) Although laser machining does not have the problems of tool wear, delamination and burr defects during machining and has high machining efficiency, there are heat-affected zones and ablated oxide layers on the surface of UHTCMCs after machining.The area of the heat-affected zone and the thickness of the ablated oxide layer can be decreased using the ultrashort pulse (such as femtosecond laser) method, optimized laser settings and the addition of protective gas.For example, Mahmod [91] performed laser machining on UHTCMCs after optimizing laser settings with a femtosecond laser.A better laser surface treatment was achieved, and the thickness of the ablative oxide layer was reduced to 8.3 μm, about 60% of that before optimization.The laser machining method of UHTCMCs still needs to be based on numerical simulation software.The removal mechanism of ultrahigh-temperature ceramic matrix composites was thoroughly investigated using laser ablation experiments, and new technological measures were proposed to reduce the area of the heat-affected zone and the thickness of the ablation oxide layer.
(3) In comparison to traditional machining, ultrasonic vibration-assisted machining minimizes tool wear and, to a certain extent, suppresses delamination and burr flaws.At the same time, ultrasonic machining has a better machining effect on UHTCMCs.The Ra (2) Although laser machining does not have the problems of tool wear, delamination and burr defects during machining and has high machining efficiency, there are heataffected zones and ablated oxide layers on the surface of UHTCMCs after machining.The area of the heat-affected zone and the thickness of the ablated oxide layer can be decreased using the ultrashort pulse (such as femtosecond laser) method, optimized laser settings and the addition of protective gas.For example, Mahmod [91] performed laser machining on UHTCMCs after optimizing laser settings with a femtosecond laser.A better laser surface treatment was achieved, and the thickness of the ablative oxide layer was reduced to 8.3 µm, about 60% of that before optimization.The laser machining method of UHTCMCs still needs to be based on numerical simulation software.The removal mechanism of ultrahigh-temperature ceramic matrix composites was thoroughly Coatings 2023, 13, 187 21 of 27 investigated using laser ablation experiments, and new technological measures were proposed to reduce the area of the heat-affected zone and the thickness of the ablation oxide layer.
(3) In comparison to traditional machining, ultrasonic vibration-assisted machining minimizes tool wear and, to a certain extent, suppresses delamination and burr flaws.At the same time, ultrasonic machining has a better machining effect on UHTCMCs.The Ra of TiB 2 /SiC is about 35% lower than that of SiC, and the Rz is about 13% lower than that of SiC [97].Although ultrasonic vibration-assisted machining increases the precision of the machining, machining flaws cannot be entirely avoided, and the price of a complete set of ultrasonic vibration-assisted machining equipment makes it impractical to use on a large scale in actual production.At the same time, in order to improve the machining quality of UHTCMCs, it is also necessary to further investigate the coupling mechanism between the ultrasonic vibration tool and the material, the mechanism via which the material is removed when vibrated, the development of new ultrasonic vibration equipment, the optimization of the machine, etc.
(4) Lastly, although research on machining UHTCMCs using other nontraditional machining methods (ion beam, electron beam, water jet, etc.) or hybrid machining methods has been carried out; overall, the machining methods need to be improved.The influence of different machine parameters and types of different UHTCMCs should be considered in the experimental machining, and the possibility of efficient, precise, stable and non-destructive machining should also be explored.

Conclusions
This review summarized the current state of research and development potential for nontraditional machining methods in the machining of UHTCMCs, in addition to highlighting machining problems and defects.Some prospects that can be considered for nontraditional machining of UHTCMCs are described below: 1.
Nontraditional machining methods need a series of technical innovations to meet the requirements of UHTCMCs machining.In addition, it is necessary to establish an analytical or numerical model to understand the cutting mechanics, in addition to further preliminary studies in the basic areas of the removal mechanism of UHTCMCs.

2.
The study of how various UHTCMCs material removal processes affect their mechanical properties (i.e., fatigue, creep and degradation) is of great interest to the aerospace and nuclear sectors.

3.
The development of machining methods suitable for UHTCMCs is still in its early stages.For example, some researchers use diamond abrasive cutting technology to machine UHTCMCs, but the machining time is long and the tool wear is too large, increasing the machining cost by 60%-90% [156].Researchers in the machining field need to work with materials scientists to explore more efficient and reliable methods of machining UHTCMCs.4.
Due to the specificity of nontraditional machining, some machining techniques have a negative impact on the environment.In the future, the large-scale machining and manufacturing of UHTCMCs should not only consider the machining efficiency and machining cost but should also consider the impact on the environment.

Figure 3 .
Figure 3. Analysis and schematic diagram of laser machining for boride-based UHTCMCs.(a) Laser ablation of composite coating schematic diagram; (b) temperature of the back surface substrate at various laser power densities.Reprinted/adapted with permission from Ref. [90].Copyright 2021, Elsevier.(c) Relationship between bending strength and defect length of three ceramics.Reprinted/adapted with permission from Ref. [92].Copyright 2020, Elsevier.

Figure 3 .
Figure 3. Analysis and schematic diagram of laser machining for boride-based UHTCMCs.(a) Laser ablation of composite coating schematic diagram; (b) temperature of the back surface substrate at various laser power densities.Reprinted/adapted with permission from Ref. [90].Copyright 2021, Elsevier.(c) Relationship between bending strength and defect length of three ceramics.Reprinted/adapted with permission from Ref. [92].Copyright 2020, Elsevier.

Figure 4 .
Figure 4. Finite element simulation for laser machining carbide-based UHTCMCs.(a) Nanosecond laser-induced controlled oxidation of TiB2-TiC ceramic composites for subsequent micro-milling; (b) sectional thickness of the metamorphic layer in the auxiliary gas environment.Reprinted/adapted with permission from Ref. [118].Copyright 2022, Elsevier.

Figure 4 .
Figure 4. Finite element simulation for laser machining carbide-based UHTCMCs.(a) Nanosecond laser-induced controlled oxidation of TiB 2 -TiC ceramic composites for subsequent micro-milling; (b) sectional thickness of the metamorphic layer in the auxiliary gas environment.Reprinted/adapted with permission from Ref. [118].Copyright 2022, Elsevier.

Figure 9 .
Figure 9. Machining efficiency, precision, cost and environmental impact of different nontraditional machining methods of UHTCMCs.(The radius of the circle indicates the machining cost; the larger the radius, the higher the cost.The color of the circle indicates the environmental impact of manufacturing, while green, yellow and red indicate small, medium and large impacts).

Figure 9 .
Figure 9. Machining efficiency, precision, cost and environmental impact of different nontraditional machining methods of UHTCMCs.(The radius of the circle indicates the machining cost; the larger the radius, the higher the cost.The color of the circle indicates the environmental impact of manufacturing, while green, yellow and red indicate small, medium and large impacts).

Table 1 .
Summary of nontraditional machining of boride-based UHTCMCs.The Ra of ZrB 2 -SiC and ZrB 2 -SiC HfB 2 after machining was 0.6 µm and 1 µm, respectively.The Rt measured 4.9 µm and 7.5 µm.The surface microcracks reduce the bending strength by 26.4% on average.Nb x Zr 1-x ) B 2 -SiC was 0.5 and 0.75, the MRR and Ra of the material were the highest, at 23.7 and 23.6 mm 2 /min, and 1.06 and 1.09 µm, respectively.
13,003Coatings 2023,13, 187 µm, in which the size of TiB particles was 3 to 5 µm, and the Ra of SiC workpiece materials ranges from 2.1 to 7.54 µm.SiC composites with 5 vol.%ZrC and 2.5 vol.%C f were enhanced, the material had a relative density of 99.6%, a hardness of 18 GPa and a bending strength of 565 MPa.
• C and an applied pressure of 50 Mpa were used to result in appropriate densification.The qualities of sintered ceramic composites may be improved due to ZrB 2 's natural fire resistance.Ghasali [100], 2018 ZrB 2 -SiC-ZrC-C f When ZrB 2 -18.5 vol.%

Table 2 .
Summary of nontraditional machining of carbide-based UHTCMCs.