Light-Induced Surface Wrinkling on Azo-Based Composite Films

: Here we report a simple micro/nano patterning strategy based on light-induced surface wrinkling. Namely, we fabricated a ﬁlm/substrate system composed of polydimethylsiloxane (PDMS) as a soft substrate and non-photosensitive polymer polystyrene (PS) mixed with azo-polymer (polydisperse orange 3, PDO 3 ) as a stiff ﬁlm. Taking advantage of the photo-thermal effect and photo-softening effect of PDO 3 , we fabricated various microstructured wrinkling morphologies by a simple light illumination. We investigated the inﬂuence of two exposure modes (i.e., static selective exposure and dynamic moving exposure), the illumination conditions, the composition of the blended ﬁlm, and the ﬁlm thickness on the resulting wrinkling patterns. It is highly expected that this azo-based photosensitive wrinkling system will be extended to functional systems for the realization of light-induced surface micro/nanopatterning.


Introduction
Surface wrinkling, as a common natural phenomenon, has attracted great attention in the past 20 years. This is because surface wrinkling, as a simple method, can be used to quickly and accurately characterize the Young's modulus, residual stress, and polymer viscoelasticity of thin films. At the same time, surface wrinkling also provides a novel, universal, simple, and efficient self-assembly technology to realize the micro/nanostructure of the material surface [1][2][3][4][5][6][7][8]. The obtained wrinkling morphologies have wide application prospects in the fields of adjustable interfacial adhesion [9][10][11][12], microfluidics [13], wettability regulation [14,15], energy collection [16], adjustable optical devices [17,18], sensors [19], and so on. The common wrinkling systems studied currently are film/substrate bilayer systems based on thin stiff layers such as metals [20,21], polymers [1,22,23], and thicker soft substrates such as polydimethylsiloxane (PDMS) [24][25][26][27][28][29]. When stimulated by external stimulation such as temperature [1], humidity [30], and solvent [31] or mechanical forces such as tension/compression [32], the film/substrate bilayer system will be subjected to compressive stress due to the modulus mismatch between the surface stiff layer and the soft substrate. In order to minimize the energy of the system, wrinkles will occur on the surface of the material.
Compared with other stimulation, light has the characteristics of remote, non-contact, and spatio-temporal manipulation. When light-sensitive materials are used as surface stiff film, light can be used as an external stimulation to control surface wrinkling. So far, remarkable progress has been made in light-controlled surface wrinkling [33][34][35][36]. For example, Jiang et al. [23] modified a PDMS substrate by adding a small amount of carbon nanotube (CNT), while photodimerized polymer was used as the surface stiff layer. Taking advantage of the photothermal conversion ability of the CNT in the underlying PDMS, they realized the reversible control of wrinkles which is vertically oriented to the exposure boundary through the selective irradiation of different photomasks. Our

Fabricatin of PDMS Elastic Substrate
The PDMS base and curing agent were fully stirred at a 10:1 weight ratio, and then the mixture was poured into a clean petri dish. After vacuum degassing, the mixture was heated at 80 • C for 3 h to complete curing and crosslinking. The obtained PDMS substrate was cut into 1 cm × 1 cm for further use.

Synthesis of Poly (Disperse Orange 3)
The chemical structure of PDO 3 is shown in Figure 1. PDO 3 was synthesized by the polymerization of BADGE and DO 3 [1,37]. Simply, BADGE and DO 3 with a molar ratio of 1:1 were polymerized at 110 • C for 48 h. After cooling, the mixture was dissolved in THF with stirring for 48 h, followed by dropwise addition into anhydrous methanol. The resulting precipitates were dissolved in THF/methanol and the extraction process was repeated twice. The final product was dried in vacuum and preserved away from light.

The Fabrication of the (PDO3-PS)/PDMS Film/Substrate System
The PDO3 and PS solutions with different weight ratios were obtained by dissolving PDO3 and PS in THF, respectively. Then, the mixed solution was obtained by mixing the THF solutions of PDO3 (e.g., 4 wt.% and 6 wt.%) and PS (e.g., 2 wt.%, 4 wt.%, 6 wt.%, and

The Fabrication of the (PDO 3 -PS)/PDMS Film/Substrate System
The PDO 3 and PS solutions with different weight ratios were obtained by dissolving PDO 3 and PS in THF, respectively. Then, the mixed solution was obtained by mixing the THF solutions of PDO 3 (e.g., 4 wt.% and 6 wt.%) and PS (e.g., 2 wt.%, 4 wt.%, 6 wt.%, and 8 wt.%) with different concentrations. The elastic substrate PDMS was first treated in a plasma processor (PDC 32G system, Harrick Plasma, Ithaca, NY, USA) for 30 s. The (PDO 3 -PS)/PDMS bilayer film/substrate system was then prepared by spin-coating the (PDO 3 -PS) mixed solution in THF to the PDMS soft substrate. Typical (3% PDO 3 -1% PS) blended films were obtained by spin-coating deposition of the mixed THF solution containing 3 wt.% PDO 3 and 1 wt.% PS.

Surface Wrinkling of the (PDO 3 -PS)/PDMS Bilayer Induced by Static Selected Exposure to Laser Light
The as-prepared (PDO 3 -PS)/PDMS bilayers were exposed to a 450 nm laser light with various light intensities (from 3.79 to 6.40 W·cm −2 ) and irradiation times (from 30 to 120 s) and then cooled to room temperature after the light source was switched off. The light intensity was modulated by the input voltage of the light source. The copper grid used as a photomask was conformally covered on the film surface. After selective exposure was performed for a designated time, the copper grid was removed carefully. The resulting samples were kept in the dark for the subsequent experiments.

Surface Wrinkling of the (PDO 3 -PS)/PDMS Bilayer Induced by Direct Laser Writing
The as-prepared (PDO 3 -PS)/PDMS samples were exposed to a 450 nm laser light with various light intensities (from 5.07 to 16.20 W·cm −2 ) and moving speeds. A motion controller (LTS300 Long Travel Stage, Thorlabs, Newton, NJ, USA) was used to control the movement of the laser beam with a certain speed (varied from 0.1 to 2 mm·s −1 ). The resulting samples were kept in the dark for the subsequent experiments.

Characterization
The wrinkle morphology was characterized by using an inverted Observer Al optical microscope (Zeiss, Jena, Germany). The temperature change during the light irradiation was probed by an infrared camera (Ti450, FLUKE, Everett, WA, USA). The thickness of composite film was characterized by a thermal field emission scanning electron microscope (JSM-7800F, JEOL, Tokyo, Japan). The wrinkle wavelength (λ) is defined as the distance between two adjacent peaks and λ is measured by taking the average of at least fifteen peak-to-peak distances of parallel segments.

Results and Discussion
The schematic diagram of the different patterned surface wrinkle microstructures of the (PDO 3 -PS)/PDMS film/substrate system fabricated by two exposure modes is shown in Figure 2. One of the exposure modes is static selective exposure ( Figure 2, route I). The copper grid used as a photomask is put on the surface of the (PDO 3 -PS)/PDMS sample ( 1 ), and then the sample is exposed to a 450 nm laser beam. Labyrinth wrinkles are formed on the surface of the exposed area, while oriented wrinkles perpendicular to the exposed area are formed on the unexposed area ( 2 ). The other exposure mode is dynamic moving exposure ( Figure 2, route II), i.e., the surface of the (PDO 3 -PS)/PDMS film/substrate system is illuminated by a moving 450 nm laser beam. The exposed area forms the oriented wrinkles ( 3 ) parallel to the moving direction, while the unexposed area still maintains the original flat state. on the surface of the exposed area, while oriented wrinkles perpendicular to the exposed area are formed on the unexposed area (②). The other exposure mode is dynamic moving exposure ( Figure 2, route Ⅱ), i.e., the surface of the (PDO3-PS)/PDMS film/substrate system is illuminated by a moving 450 nm laser beam. The exposed area forms the oriented wrinkles (③) parallel to the moving direction, while the unexposed area still maintains the original flat state.

Static Selective Exposure
As shown in Figure 3a, wrinkles are formed on the surface of (PDO3-PS)/PDMS bilayer system after laser light irradiation. For the previously reported traditional bilayer system (e.g., PS/PDMS) [38,39], the surface wrinkling was basically induced by stimulations such as mechanical force and heating that required complex experimental steps. However, the wrinkles here are formed on the surface of the (PDO3-PS)/PDMS bilayer system simply through a single light irradiation step. Furthermore, in contrast to the wrinkles with a simple morphology and the single orientation state of a common wrinkling system, our selective-exposure-induced wrinkles are more hierarchical, i.e., labyrinth wrinkles are formed on the surface of the exposed region and oriented wrinkles are formed on the surface of the unexposed region. The in situ monitoring of the optical microscope showed that the whole surface of the film/substrate system remains smooth during illumination. After light illumination, the surface wrinkling occurs almost at the same time on the exposed area and unexposed area, and the wrinkling morphology becomes clearer as time goes on. The corresponding infrared thermal monitoring showed that the surface temperature of the film/substrate system increases gradually during the illumination. For example, when (3% PDO3-1% PS)/PDMS (hf = 59 nm) is irradiated by laser light with I = 3.79 W·cm −2 for 30 s, the surface temperature reaches about 102 °C ( Figure S2). After the laser light exposure, the surface temperature decreases gradually. Obviously, the surface temperature change of the composite system originates from the 450 nm laser illumination. Because PS and PDMS have no photothermal conversion ability, the photothermal conversion effect comes from PDO3. Moreover, the surface wrinkling is related to the photothermal effect.

Static Selective Exposure
As shown in Figure 3a, wrinkles are formed on the surface of (PDO 3 -PS)/PDMS bilayer system after laser light irradiation. For the previously reported traditional bilayer system (e.g., PS/PDMS) [38,39], the surface wrinkling was basically induced by stimulations such as mechanical force and heating that required complex experimental steps. However, the wrinkles here are formed on the surface of the (PDO 3 -PS)/PDMS bilayer system simply through a single light irradiation step. Furthermore, in contrast to the wrinkles with a simple morphology and the single orientation state of a common wrinkling system, our selective-exposure-induced wrinkles are more hierarchical, i.e., labyrinth wrinkles are formed on the surface of the exposed region and oriented wrinkles are formed on the surface of the unexposed region. The in situ monitoring of the optical microscope showed that the whole surface of the film/substrate system remains smooth during illumination. After light illumination, the surface wrinkling occurs almost at the same time on the exposed area and unexposed area, and the wrinkling morphology becomes clearer as time goes on. The corresponding infrared thermal monitoring showed that the surface temperature of the film/substrate system increases gradually during the illumination. For example, when (3% PDO 3 -1% PS)/PDMS (h f = 59 nm) is irradiated by laser light with I = 3.79 W·cm −2 for 30 s, the surface temperature reaches about 102 • C ( Figure S2). After the laser light exposure, the surface temperature decreases gradually. Obviously, the surface temperature change of the composite system originates from the 450 nm laser illumination. Because PS and PDMS have no photothermal conversion ability, the photothermal conversion effect comes from PDO 3 . Moreover, the surface wrinkling is related to the photothermal effect. PDO 3 is a typical pseudo-stilbene azobenzene polymer with an absorption band of 400-600 nm. A distinctive feature of PDO 3 is that its n−π* absorption band is buried underneath the π−π* band and thus they are overlapped with the maximal peak at ∼470 nm ( Figure S3). Namely, the 450 nm laser light can be absorbed simultaneously by the transand cis-isomers, which facilitates the trans/cis/trans isomerization cycle. In our case, during exposure to 450 nm laser light, the exposed (PDO 3 -PS)/PDMS is heated by the photothermal conversion effect of PDO 3 [40,41], leading to a significantly increased surface temperature T h (T h is the elevated temperature due to the photothermal effect). Due to the mismatch of thermal expansion coefficients between the PDO 3 -PS film and the PDMS substrate, a compressive stress (σ) is generated during the cooling process after the irradiation, and σ can be expressed as is the plane strain modulus of the film, where E f is the Young's modulus of the film. v is Poisson's ratio, ε is the compressive strain, and α s and α f are the linear thermal expansion coefficients of the substrate and the film, respectively.
where T is the cooling temperature that would decrease from T h to room temperature~22 • C. When the σ caused by the photothermal effect exceeds the critical value (σ c ) (Equation (2)), in order to minimize the free energy of the system, spontaneous wrinkling of the surface occurs.
where ε c is the critical wrinkling strain. According to the linear buckling theory [20,27,42], the critical wrinkling wavelength (λ c ) of the film/substrate system is shown in Equation (3): where h f is the film thickness and E s is the plane strain modulus of the substrate. The adjustment of the wrinkle wavelength (λ) can be achieved by simply tuning the parameters such as the film thickness and modulus of PDO 3 -PS. This has been fully exploited in subsequent experiments.  PDO3 is a typical pseudo-stilbene azobenzene polymer with an absorption band of 400-600 nm. A distinctive feature of PDO3 is that its n−π* absorption band is buried underneath the π−π* band and thus they are overlapped with the maximal peak at ∼470 nm ( Figure S3). Namely, the 450 nm laser light can be absorbed simultaneously by the transand cis-isomers, which facilitates the trans/cis/trans isomerization cycle. In our case, during exposure to 450 nm laser light, the exposed (PDO3-PS)/PDMS is heated by the photothermal conversion effect of PDO3 [40,41], leading to a significantly increased surface temperature Th (Th is the elevated temperature due to the photothermal effect). Due to the mismatch of thermal expansion coefficients between the PDO3-PS film and the PDMS substrate, a compressive stress (σ) is generated during the cooling process after the irradiation, and σ can be expressed as is the plane strain modulus of the film, where Ef is the Young's modulus of the film. v is Poisson's ratio, ε is the compressive strain, and αs and αf are the linear thermal expansion coefficients of the substrate and the film, respectively. ΔT = Upon light irradiation, the temperature of the exposed area increases due to the photothermal conversion effect of PDO 3 . This further induces isotropic compressive stress in the film/substrate system during the subsequent cooling process, which results in the formation of random labyrinth wrinkles. Although the unexposed area is not irradiated by the laser light, the heat generated in the exposed area can be transferred to the adjacent unexposed area, leading to the formation of compressive stress in the unexposed area. Moreover, due to the existence of the photosoftening effect of PDO 3 [1,[43][44][45], the modulus of the exposed area is lower than that of the unexposed area, which induces an in situ soft/hard boundary on the surface. Therefore, the unexposed area is finally subjected to anisotropic compressive stress parallel to the soft/hard boundary, leading to the formation of corresponding oriented wrinkles perpendicular to the compressive stress, i.e., the final wrinkle orientation of the unexposed region is perpendicular to the exposed region ( Figure 3a). Furthermore, we investigated the influence of illumination conditions (light intensity (I) and exposing time (t)), the type of copper grids, and film thickness (h f ) for selective exposure on the resulting surface morphology of the (PDO 3 -PS)/PDMS film/substrate system.
As expected from Equation (3), the wrinkle wavelength of the exposed area is smaller than that of the unexposed area because of the modulus decrease of the exposed area ( Figure 3b). Naturally, the decrease in the modulus caused by the photosoftening effect of PDO 3 will be greatly enhanced with the increase of the light intensity [43,44,46]. Therefore, the wrinkle wavelength of both the exposed area and unexposed area decreases with the increase of the illuminating light intensity (Figure 3b). Similarly, with the increase of exposing time, the degree of photosoftening of PDO 3 will be greater, leading to the decrease of the wrinkle wavelength on the surface of the (3% PDO 3 -1% PS)/PDMS accordingly ( Figure S4).
The influence of the type of copper grids on the surface wrinkle morphology of 3% PDO 3 -1% PS blend films induced by selective exposure is shown in Figure 4a-c. The results show that the geometric shape and size of the current exposed and unexposed area (i.e., the type of copper grids used for selective exposure (including the geometric shape of the copper grids holes and the mesh size of the copper grids)) have no significant influence on the wrinkle orientation. Namely, labyrinth wrinkles are formed on the exposed area and oriented wrinkles are formed on the unexposed area after selective exposure via different types of copper grids, which is further confirmed by Figure S5. Furthermore, we investigated the influence of film thickness on the wrinkle wavelength ( Figure 4d). As expected from Equation (3), the surface wrinkle wavelength on the exposed/unexposed area increases with the increase of the film thickness when the type of copper grid and light intensity are fixed.

Dynamic Moving Exposure
On the basis of the static selective exposure, we further explored the light-response behavior of the (PDO3-PS)/PDMS film/substrate system upon the moving exposure (Figure 1, route Ⅱ). As shown in Figure 5a, after moving exposure, the central region of the exposed area on the film/substrate system forms the oriented wrinkles. The wrinkles of

Dynamic Moving Exposure
On the basis of the static selective exposure, we further explored the light-response behavior of the (PDO 3 -PS)/PDMS film/substrate system upon the moving exposure (Figure 1, route II). As shown in Figure 5a, after moving exposure, the central region of the exposed area on the film/substrate system forms the oriented wrinkles. The wrinkles of two sides regions near the unexposed area are bent outward relative to the parallel wrinkles. The unexposed area still maintains the initial flat state. Obviously, this is quite different from the random labyrinth wrinkles formed on the exposed area and the oriented wrinkles perpendicular to the exposed/unexposed boundary formed on the unexposed area after selective exposure. Furthermore, in contrast to the common boundary effect resulting in oriented wrinkling perpendicular to the bas-relief edges, our moving-exposure-induced aligned wrinkles are parallel to the exposed/unexposed boundary [20]. As discussed above, due to the local photosoftening effect of azo polymer, the modulus of the exposed region decreases during laser light irradiation, while the modulus of the unexposed region has little change. As a result, a new soft/hard boundary is formed due to the modulus difference between the exposed/unexposed area. Upon moving the laser exposure, the exposed soft area is subjected to anisotropic compressive stress perpendicular to the soft/hard boundary [21,47], which causes the formation of the oriented wrinkles parallel to the soft/hard boundary on the surface of the exposed soft area. Moreover, due to the Gaussian distribution of the laser output, the light intensity in the center of the laser spot is higher than that in the edge spot. Thus, the degree of photo-softening of the edge region on the exposed area is relatively weak, which further induces the tendency of the wrinkles of the edge region to be vertically oriented to the boundary dominated by the geometric boundary effect. Meanwhile, due to the influence of the soft/hard boundary effect, the final orientation of the wrinkle on the edge region is between the parallel orientation and perpendicular orientation.
Furthermore, the influence of the laser light intensity (I) on wrinkling was investigated. When the laser beam was controlled to move in a straight line at the speed of 1 mm·s −1 and the light intensity increased from 5.07 to 10.04 W·cm −2 (Figure 5a-e), the wavelength of the parallel oriented wrinkles decreased with the increase of I, and the path width of the whole wrinkling region increased with the increase of I. The related data statistics are shown in Figure 5f. This correlation is attributed to the fact that the heat gen- As discussed above, due to the local photosoftening effect of azo polymer, the modulus of the exposed region decreases during laser light irradiation, while the modulus of the unexposed region has little change. As a result, a new soft/hard boundary is formed due to the modulus difference between the exposed/unexposed area. Upon moving the laser exposure, the exposed soft area is subjected to anisotropic compressive stress perpendicular to the soft/hard boundary [21,47], which causes the formation of the oriented wrinkles parallel to the soft/hard boundary on the surface of the exposed soft area. Moreover, due to the Gaussian distribution of the laser output, the light intensity in the center of the laser spot is higher than that in the edge spot. Thus, the degree of photo-softening of the edge region on the exposed area is relatively weak, which further induces the tendency of the wrinkles of the edge region to be vertically oriented to the boundary dominated by the geometric boundary effect. Meanwhile, due to the influence of the soft/hard boundary effect, the final orientation of the wrinkle on the edge region is between the parallel orientation and perpendicular orientation.
Furthermore, the influence of the laser light intensity (I) on wrinkling was investigated. When the laser beam was controlled to move in a straight line at the speed of 1 mm·s −1 and the light intensity increased from 5.07 to 10.04 W·cm −2 (Figure 5a-e), the wavelength of the parallel oriented wrinkles decreased with the increase of I, and the path width of the whole wrinkling region increased with the increase of I. The related data statistics are shown in Figure 5f. This correlation is attributed to the fact that the heat generated by the photothermal conversion effect of PDO 3 increases with the increase of I (e.g., when I increases from 5.07 to 10.04 W·cm −2 , the temperature increases from 176.2 to 221.5 • C) ( Figure S6). Thus, the degree of photosoftening also increases with the increase of I, i.e., the modulus of the central area in the PDO 3 -PS film (E f ) decreases with the increase of I. According to Equation (3), it can be expected that the wavelength of the parallel oriented wrinkles of the central area will decrease with the increase of I. Moreover, due to the Gaussian distribution of the laser intensity, the temperature on the exposed area is higher in the center and lower in the two sides. When the light intensity is small, only the central region can meet the critical wrinkling condition (σ > σ c ). Subsequently, the increases of light intensity result in the increase of the temperature of the exposed area, gradually leading to the thermal-induced compressive stress increases. Therefore, the wider area meets the critical wrinkling condition, and then wrinkles are formed on the wider area. Similarly, the oriented wrinkle wavelength decreases with the decrease of the moving speed (V), and the wrinkling path width increases with the decrease of V ( Figure S7).
The influence of PS content on the wrinkling induced by moving laser irradiation is shown in Figure 6. Under the condition of I = 10.53 W·cm −2 and V = 1 mm·s −1 , the wrinkle wavelength of the exposed area of the (PDO 3 -PS)/PDMS system increases with the increase of PS content, while the wrinkling path width decreases with the increase of PS content (Figure 6d). The variation is the same for the other light intensities applied ( Figure S8). Since PS is a non-photosensitive polymer, light irradiation has nearly no influence on the modulus of PS. Therefore, the higher the content of PS, the smaller the decrease of the modulus of the PDO 3 -PS blended film caused by light irradiation. In addition, the SEM results of the cross section of the blend film show that the thicknesses of the three films with PS contents of 2%, 3%, and 4% were 235, 375, and 514 nm, respectively ( Figure S9). Namely, with the increase of PS content, the modulus and thickness of the blended film both increase, so the corresponding wrinkle wavelength increases according to Equation (3). For the PDO 3 -PS films, the overall modulus increases with the increase of PS content, and the critical wrinkling stress (σ c ) increases according to Equation (2). Thus, the path width of the area which can meet the critical wrinkling condition decreases with the increase of PS content. Moreover, the orientation degree of the ordered wrinkles on the exposed area increases with the increase of PS content, which may be related to the boundary effect. It has been reported previously [48,49] that the increase of wrinkle wavelength λ and the decrease of wrinkling path width (D) lead to the increase of λ/D and the enhancement of the corresponding boundary effect, which finally leads to the more obvious wrinkle orientation (Figure 6a-c).
Here, we further wrote wrinkled micropatterns such as "TJU" on the surface of the film/substrate system by controlling the moving path of the laser beam, i.e., using laser direct writing technology (Figure 7a). The result of Figure 7b shows that the written wrinkle orientation remains highly parallel to the direction of laser writing even under the curved writing path.
In general, in order to obtain highly oriented surface wrinkles of the bilayer system, a template is usually used to pattern the substrate or surface layer [50,51]. In contrast to their methods, our light-controlled moving exposure strategy is more flexible in that the ordered surface wrinkle morphology and pattern information of any prefabricated path can be easily obtained by using this simple laser direct writing technology.
width of the area which can meet the critical wrinkling condition decreases with th crease of PS content. Moreover, the orientation degree of the ordered wrinkles on th posed area increases with the increase of PS content, which may be related to the bo ary effect. It has been reported previously [48,49] that the increase of wrinkle wavele λ and the decrease of wrinkling path width (D) lead to the increase of λ/D and th hancement of the corresponding boundary effect, which finally leads to the more ob wrinkle orientation (Figure 6a-c).  Here, we further wrote wrinkled micropatterns such as "TJU" on the surface of the film/substrate system by controlling the moving path of the laser beam, i.e., using laser direct writing technology (Figure 7a). The result of Figure 7b shows that the written wrinkle orientation remains highly parallel to the direction of laser writing even under the curved writing path. In general, in order to obtain highly oriented surface wrinkles of the bilayer system, a template is usually used to pattern the substrate or surface layer [50,51]. In contrast to their methods, our light-controlled moving exposure strategy is more flexible in that the ordered surface wrinkle morphology and pattern information of any prefabricated path can be easily obtained by using this simple laser direct writing technology.

Conclusions
In this paper, a non-photosensitive polymer PS is introduced to form a photosensitive blended film by mixing with an azo polymer PDO3, which results in controllable lightinduced wrinkling on the surface of the blended film by exploiting the unique photoresponsivity of PDO3. Under the static selective exposure mode, random wrinkles are formed on the exposed area, and oriented wrinkles perpendicular to the boundary are formed on the unexposed area. Under the dynamic moving exposure mode, the exposed

Conclusions
In this paper, a non-photosensitive polymer PS is introduced to form a photosensitive blended film by mixing with an azo polymer PDO 3 , which results in controllable light-induced wrinkling on the surface of the blended film by exploiting the unique photoresponsivity of PDO 3 . Under the static selective exposure mode, random wrinkles are formed on the exposed area, and oriented wrinkles perpendicular to the boundary are formed on the unexposed area. Under the dynamic moving exposure mode, the exposed area forms aligned wrinkles that are highly parallel to the laser writing direction. The influence of the illumination conditions, film thickness, and composition of the blended film on the wrinkle morphology were systematically investigated. The all-optical surface wrinkling strategy based on the azo polymer blended film/substrate system reported in this paper is expected to be extended to other blended systems with functional components, which would realize the light-induced surface micro/nano patterning of functional composite film, and broaden its use in the fields of information writing and anti-counterfeiting.