Research on Laser Cladding Co-Based Alloy on the Surface of Vermicular Graphite Cast Iron

To further improve the hardness of the laser cladding layer on the surface of the vermicular graphite cast iron, the structural parameters of the laser cladding Co-base were designed and optimized, and the properties of the clad layer were evaluated using optical microscopy (OM), scanning electron microscopy (SEM), energy spectroscopy (EDS), X-ray diffractometer (XRD), electrochemical workstation, and friction wear equipment. The results show that the average hardness of the molten layer of Ni and Co-based composite cladding layer is 504 HV0.5, which is 0.64 times that of the Co-based cladding layer due to the combined factors of Ni-Cr-Fe equivalent to the dilution of the Ni-based cladding layer to the Co-based cladding layer. Due to the potential difference of the Ni, Cr, and Co elements on the surface of the cladding layer, the self-corrosion potential of the Ni and Co-based composite cladding layer is 1.08 times that of the Co-based cladding layer, and the self-corrosion current density is 0.51 times. Laser cladding Co-based cladding layer has high corrosion resistance. Under the influence of plastic deformation and oxidative wear of the cladding layer of the Ni and Co-based composite cladding layer, the wear amount of the cladding layer of the Ni and Co-based composite cladding layer is less.


Introduction
Vermicular graphite cast iron has good thermal conductivity and thermal fatigue properties, and is often used to manufacture cylinder heads for engines [1][2][3][4]. In engineering, in order to achieve the engine intake and exhaust function, the cylinder head is designed with intake and exhaust holes and an upper valve seat is mounted. The traditional inlay valve seat way in the service process, by the valve high-frequency impact effect, valve seat off failure frequently. In order to improve the durability of the valve seat in the service process, the new power is integrated with a cylinder head and a valve seat. Since valve seats require a material surface resistant to wear, the overall valve seat surface needs to increase its abrasion resistance using the modified process [5,6]. The main methods used to modify and improve the hardness of valve seats are high frequency induction phase change hardening, laser phase change hardening, laser melting, and laser cladding [7,8]. The use of high-frequency induction phase hardening, which requires the development of special induction coils for the shape of the valve seat, a method that primarily involves heating ductile iron above the phase hardening hardness and using rapid cooling in phase change hardening regions to form martensite tissue. Laser phase hardening and high-frequency induction phase hardening are basically the same in principle, also generating a layer of high hardness martensite tissue on the surface. Laser melting is the use of high-power density laser to generate a layer of high hardness Leylandite on the surface of the material, but the Leylandite organization is brittle and affects the service life of the valve seat in the service environment [9]. Martensite generated by phase hardening method, when the valve seat temperature reaches 500 • C under service conditions, the martensite will experience hardness deterioration [10]. When the protective coating is prepared by laser cladding, the material design of the cladding layer can be made according to the service conditions of the valve seat, combining the advantages of the high-power density of the laser and fast scanning speed of the laser cladding, the organization of the formed cladding layer is relatively small and the cladding layer and the substrate can be metallurgically bonded. The main difficulties in the existing laser melting of high hardness protective coatings on cast iron are the high crack sensitivity of cast iron, the formation of crack defects on the surface during the laser melting process, and the diffusion of graphite from the substrate into the clad layer, which affects the performance of the clad layer.
To obtain laser-prepared high-performance cladding layers, Li et al. [11] investigated the effect of different structural designs of the substrate on the properties of the cladding layers and obtained a cladding layer structure that reduces stress. Liu [12] prepared multilayer cladding layers on the surface of ductile iron by using laser cladding in order to solve the problem of bond interface brittleness and evaluated the properties of the cladding layers. Ding [13] prepared a cobalt-based protective layer on a steel valve seat and evaluated the performance of the protective layer. S. Selvi [14] carried out a study on the preparation of protective layers on mild steel valve seats using the manual metal arc welding process. Paczkowska et al. [15] evaluated the possibility of laser melting of cobalt-based cladding on the surface of ductile cast iron, and also carried out the surface modification of ductile cast iron valve seats to study the organization and hardness of the clad layer by varying different cooling rates and thus, obtaining a clad layer with high hardness, fine organization, and high-temperature resistance. Bourahima et al. [16] investigated the effect of process parameters on the nickel-based cladding layer and cast iron substrate, using a combination of experimental and numerical analysis to vary the process parameters and finally prepare a crack-free cladding layer with the desired geometry on the cast iron surface.
Although there has been some research on laser cladding on cast iron, the issue of how to further improve the quality of the cladding remains a hot issue of engineering concern. In this paper, the structural design of the laser cladding layer is optimized, and its performance is evaluated. The research results provide support for the optimization of process parameters in engineering.

Experimental Materials and Methods
The substrate material used in the experiment was plate RT450 vermicular graphite cast iron. Before the experiment, the oxide layer on the surface of the substrate was removed with sandpaper, and then the oil stains on the surface were cleaned with acetone. The composition of non-standard nickel-based alloy powder and non-standard cobalt-based alloy powder selected for cladding is shown in Table 1. The particle size of the powder is in the range of 150 mesh to 300 mesh. Before the experiment, the powder was dried in a dryer. The drying parameters were: the drying temperature was 100-110 • C, and the drying time was 15 min. The equipment selected for the laser cladding experiment is the LDF 6000-100 fiber laser produced by the German Laserline company (Laserline, Koblenz, Germany). The laser cladding powder is a synchronous powder feeding method with a powder feeding rate of 18 g/min. Figure 1 is a schematic diagram of synchronous powder feeding. The nitrogen is used as the protective gas, and the flow rate is 18 L/min. In order to obtain a cladding layer with good surface condition and good quality forming, the parameters were optimized. The specific parameters were: the laser spot diameter is 3 mm, the laser power is 1300 W, the overlap rate is 65%, and the laser scanning speed is 10 mm/s. A layer of nickel-based transition layer with a length of 40 mm and a width of 40 mm was respectively clad on the substrate. On this basis, a cobalt-based cladding layer was clad on the surface. This sample was marked as sample 1. Two layers of cobalt-based formance of the coating is characterized. The test piece with a size of 15 mm × 15 m mm was cut, the coating was polished, and the friction and wear experiment was out using the MPX-3G type abrasion tester (HengXu, Jinan, China). SiN was sele the friction pair, and the experiment was subjected to an external load of 120 N, experiment time was 30 min. According to "Determination of the Shear Strength o  Thermal Coatings" (GB/T13222), prepare the laser cladding shear samples, and co  them as GCr15 sleeves (quenched HRC60), and test the laser cladding layer and th ing strength of compact graphite cast iron RUT-450.  Figure 2 shows the macro morphology of the cross section of the cladding lay ure 2 shows that the two cladding layer structures are dense and uniform, with After the experiment, a wire cutting machine (ZhongXin, Taizhou, China) was used to cut a metallography sample with a size of 15 mm × 15 mm × 10 mm in the direction perpendicular to the laser scanning. The mixture of water and HF+HNO 3 etched the nickel-based and cobalt-based samples. The scanning electron microscope Zeiss integrated with the energy spectrometer (ZEISS, Jena, Germany) was used to observe the structure of the coating and measure the elemental composition. The HVS-1000 Z hardness tester (LiDun, Shanghai, China) was used to perform a hardness test every 300 µm and every 200 µm in the horizontal and vertical directions of the sample. The hardness measurement load is 500 g, and the load duration is 15 s. The phase identification was characterized by an X-ray diffractometer (D/max-rA) (Rigaku, Tokyo, Japan), which worked under Cu K-α radiation (λ = 1.54 Å, 40 kV, 40 mA). The XRD pattern collection range was 10 • ≤ 2θ ≤ 100 • , and the scanning velocity was 4 • /min). The dimension of the test specimens was 15 mm × 15 mm × 10 mm. Cut a specimen with a size of 15 mm × 15 mm × 10 mm, polish the coating, prepare a 3.5% NaCl solution as the electrolyte, and select AgCl as the reference electrode. After immersing for 60 min, the electrochemical corrosion performance of the coating is characterized. The test piece with a size of 15 mm × 15 mm × 13 mm was cut, the coating was polished, and the friction and wear experiment was carried out using the MPX-3G type abrasion tester (HengXu, Jinan, China). SiN was selected as the friction pair, and the experiment was subjected to an external load of 120 N, and the experiment time was 30 min. According to "Determination of the Shear Strength of Metal Thermal Coatings" (GB/T13222), prepare the laser cladding shear samples, and configure them as GCr15 sleeves (quenched HRC60), and test the laser cladding layer and the bonding strength of compact graphite cast iron RUT-450.  Figure 2 shows the macro morphology of the cross section of the cladding layer. Figure 2 shows that the two cladding layer structures are dense and uniform, with a small amount of pores and no obvious cracks. The existence of a small amount of pores in the cladding layer is due to the rapid heating and cooling characteristics of the laser cladding process, which makes the amorphous powder insufficiently melted, and some space among the filled powders remained [17]. In addition, there is a clear macroscopic boundary between the cladding layer and the substrate, and the boundary line is a curve close to the horizontal on the left and right sides. A metallurgical bond is formed between the cladding layer and the substrate. The average thickness of the two different cladding layers is about 2 mm. amount of pores and no obvious cracks. The existence of a small amount of pores in the cladding layer is due to the rapid heating and cooling characteristics of the laser cladding process, which makes the amorphous powder insufficiently melted, and some space among the filled powders remained [17]. In addition, there is a clear macroscopic boundary between the cladding layer and the substrate, and the boundary line is a curve close to the horizontal on the left and right sides. A metallurgical bond is formed between the cladding layer and the substrate. The average thickness of the two different cladding layers is about 2 mm.  Figure 3a shows the surface structure of the Co-based cladding layer with a Ni-based transition layer, and Figure 3b shows the surface structure of the cladding layer without the transition layer. Figure 3a,b shows that the surface grains of the two cladding layers are fine. The surface layer of the structure with Ni-based as the transition layer is dispersed and distributed between the grains. However, there is a lamellar eutectic structure between the crystal grains without the Ni-based transition layer. This is because the laser has the characteristics of rapid heating and cooling. And the molten metal powder forms fine crystal grains under rapid solidification. Figure 3c shows the surface structure of the Co-based cladding layer at low magnification, and Figure 3d shows the bottom structure of the Co-based cladding layer at low magnification. Figure 3c,d shows the different grain growth direction of the Co-based cladding layer. The grain growth direction shows a clear difference between the surface and the bottom of the clad layer. This is because the grains grow along the approximate thermal gradient direction, and the thermal gradient and solidification rate are the most significant factors governing the grain growth [18]. Similarly, the Co-based cladding layer with a Ni-based transition layer has a similar grain growth direction. Table 2 shows the point energy spectrum data of the surface structure. Table 2 demonstrates that the surface structure of the Ni-based transition layer is enriched in Fe, Co, and Ni in the crystal nucleus, and C and Cr are enriched in the intergranular. The surface structure without the Ni-based transition layer is rich in Co and Fe in crystal nucleus, and C and Cr in the intercrystalline. According to the literature [19,20], the Cr, Mo, Fe, and C elements enriched in the dendrites mainly exist in the form of carbides. The surface structure with the transition layer is rich in Ni element between the nuclei. According to the intercrystalline enrichment of C and Cr elements, and combined with XRD analysis, the main carbides are Cr23C6 and Cr7C3. It shows that when the cobalt base is cladding on the transition layer, the transition layer is partially melted. And the melted transition layer area is fully fused with the cobalt base of the surface layer. There is a large amount of Fe element in the surface structure, which means that when the first layer is melted, the partially melted matrix enters the first layer. During the cladding of the second layer, the Fe element melted in the first layer enters the second layer. This situation is also observed in the energy spectrum scan of Figure 4.  Figure 3a shows the surface structure of the Co-based cladding layer with a Ni-based transition layer, and Figure 3b shows the surface structure of the cladding layer without the transition layer. Figure 3a,b shows that the surface grains of the two cladding layers are fine. The surface layer of the structure with Ni-based as the transition layer is dispersed and distributed between the grains. However, there is a lamellar eutectic structure between the crystal grains without the Ni-based transition layer. This is because the laser has the characteristics of rapid heating and cooling. And the molten metal powder forms fine crystal grains under rapid solidification. Figure 3c shows the surface structure of the Co-based cladding layer at low magnification, and Figure 3d shows the bottom structure of the Co-based cladding layer at low magnification. Figure 3c,d shows the different grain growth direction of the Co-based cladding layer. The grain growth direction shows a clear difference between the surface and the bottom of the clad layer. This is because the grains grow along the approximate thermal gradient direction, and the thermal gradient and solidification rate are the most significant factors governing the grain growth [18]. Similarly, the Co-based cladding layer with a Ni-based transition layer has a similar grain growth direction. Table 2 shows the point energy spectrum data of the surface structure. Table 2 demonstrates that the surface structure of the Ni-based transition layer is enriched in Fe, Co, and Ni in the crystal nucleus, and C and Cr are enriched in the intergranular. The surface structure without the Ni-based transition layer is rich in Co and Fe in crystal nucleus, and C and Cr in the intercrystalline. According to the literature [19,20], the Cr, Mo, Fe, and C elements enriched in the dendrites mainly exist in the form of carbides. The surface structure with the transition layer is rich in Ni element between the nuclei. According to the intercrystalline enrichment of C and Cr elements, and combined with XRD analysis, the main carbides are Cr 23 C 6 and Cr 7 C 3 . It shows that when the cobalt base is cladding on the transition layer, the transition layer is partially melted. And the melted transition layer area is fully fused with the cobalt base of the surface layer. There is a large amount of Fe element in the surface structure, which means that when the first layer is melted, the partially melted matrix enters the first layer. During the cladding of the second layer, the Fe element melted in the first layer enters the second layer. This situation is also observed in the energy spectrum scan of Figure 4.  In order to explore the dispersion of the alloying elements of the matrix vermicular graphite cast iron and the alloying elements of the cladding layer. The line scan analysis of the two cladding layers from the bottom of the cladding layer to the substrate was carried out. The results of the line scan analysis are shown in Figure 4. Figure 4 indicates that Fe alloying elements are distributed in both cladding layers. It can be seen that the matrix melts during the laser cladding process, and the alloy element Fe of the matrix diffuses into the cladding layer. During the laser cladding process, the alloy elements in the molten pool will flow due to the effect of heat. And the alloying elements Ni and Co in the lower part of the two cladding layers diffuse into the vermicular graphite cast iron matrix in a    Figure 5 shows the XRD patterns of the two cladding layers. Figure 5 shows that the two cladding layers are mainly composed of γ-Co, Cr23C6, Cr7C3, and Co0.72Fe0.28. Due to the rapid solidification of laser cladding, the γ-Co structure formed at high temperature is retained at room temperature. Both the nickel base and the cobalt base in the cladding powder contain a large amount of Cr element, which is a strong carbide forming element. The Cr element forms M7C3 and M23C6 carbides with the C element in the cladding material and the carbon diffused from the graphite in the matrix. And similar results have been achieved by Li [21][22][23]. In addition, in the nickel-based and cobalt-based composite cladding layer, the surface structure of the cladding layer forms a Ni-Cr-Fe intermediate phase. Figure 5 shows that the matrix element Fe diffuses into the nickel base of the transition layer during the cladding of the transition layer. During the cladding of the surface layer of the cobalt base, it further diffuses, thereby forming the Ni-Cr-Fe intermediate phase. In order to explore the dispersion of the alloying elements of the matrix vermicular graphite cast iron and the alloying elements of the cladding layer. The line scan analysis of the two cladding layers from the bottom of the cladding layer to the substrate was carried out. The results of the line scan analysis are shown in Figure 4. Figure 4 indicates that Fe alloying elements are distributed in both cladding layers. It can be seen that the matrix melts during the laser cladding process, and the alloy element Fe of the matrix diffuses into the cladding layer. During the laser cladding process, the alloy elements in the molten pool will flow due to the effect of heat. And the alloying elements Ni and Co in the lower part of the two cladding layers diffuse into the vermicular graphite cast iron matrix in a small amount. The distribution of alloying elements such as Cr and C is relatively uniform. As the distance from the substrate is closer, the content of alloying elements such as Ni and Co decreases sharply, and the content of Fe alloying elements increases sharply. The reason is that under the high temperature generated by laser cladding, micro-melting occurs between the substrate and the cladding layer, which leads to element diffusion and dilution. The above analysis shows that during the laser cladding process, the cladding layer elements (Ni and Co) and the matrix element (Fe) have been mixed. This indicates that a good metallurgical bond is formed between the cladding layer and the substrate.  Figure 5 shows the XRD patterns of the two cladding layers. Figure 5 shows that the two cladding layers are mainly composed of γ-Co, Cr 23 C 6 , Cr 7 C 3 , and Co 0.72 Fe 0.28 . Due to the rapid solidification of laser cladding, the γ-Co structure formed at high temperature is retained at room temperature. Both the nickel base and the cobalt base in the cladding powder contain a large amount of Cr element, which is a strong carbide forming element. The Cr element forms M 7 C 3 and M 23 C 6 carbides with the C element in the cladding material and the carbon diffused from the graphite in the matrix. And similar results have been achieved by Li [21][22][23]. In addition, in the nickel-based and cobalt-based composite cladding layer, the surface structure of the cladding layer forms a Ni-Cr-Fe intermediate phase. Figure 5 shows that the matrix element Fe diffuses into the nickel base of the transition layer during the cladding of the transition layer. During the cladding of the surface layer of the cobalt base, it further diffuses, thereby forming the Ni-Cr-Fe intermediate phase.   Figure 6a shows the hardness distribution from the surface of the cladding layer to the substrate. It can be observed from Figure 6a that the average hardness of the laser cladding Co-based cladding layer is 788 HV0.5. The average hardness of the Ni and Cobased composite cladding layer is 504 HV0.5. What is more, there is a hardness peak at the interface between the cladding layer and the substrate. The hardness of the laser cladding Co-based cladding layer is higher than that of the Ni and Co-based composite cladding layer. This is because the content of Cr and C in the laser cladding Co-based powder is higher than that in the Ni-based powder, and C and Cr elements have a strong affinity. After high temperature melting, the solidification process creates conditions for the formation of carbides. The formation of carbides (Cr23C6, Cr7C3) was also observed in XRD. In the Ni and Co-based composite cladding layer, the hardness of the cladding layer would be reduced due to the dilution effect of the Ni-based transition layer on the Cobased cladding layer, and the intermediate Cr-Ni-Fe generated. In the heat-affected zone, the hardness of the two cladding layers increased to 825 HV0.5 and 676 HV0.5, respectively. This is due to the formation of high-carbon martensite and ledeburite in the heat-affected  Figure 6a shows the hardness distribution from the surface of the cladding layer to the substrate. It can be observed from Figure 6a that the average hardness of the laser cladding Co-based cladding layer is 788 HV 0.5 . The average hardness of the Ni and Cobased composite cladding layer is 504 HV 0.5 . What is more, there is a hardness peak at the interface between the cladding layer and the substrate. The hardness of the laser cladding Co-based cladding layer is higher than that of the Ni and Co-based composite cladding layer. This is because the content of Cr and C in the laser cladding Co-based powder is higher than that in the Ni-based powder, and C and Cr elements have a strong affinity. After high temperature melting, the solidification process creates conditions for the formation of carbides. The formation of carbides (Cr 23 C 6 , Cr 7 C 3 ) was also observed in XRD. In the Ni and Co-based composite cladding layer, the hardness of the cladding layer would be reduced due to the dilution effect of the Ni-based transition layer on the Co-based cladding layer, and the intermediate Cr-Ni-Fe generated. In the heat-affected zone, the hardness of the two cladding layers increased to 825 HV 0.5 and 676 HV 0.5 , respectively. This is due to the formation of high-carbon martensite and ledeburite in the heat-affected zone. Figure 6b shows the lateral hardness distribution on the surface of the cladding layer. Figure 6b shows that the lateral hardness has periodic fluctuations. The periodic hardness fluctuations are due to the use of multiple laser cladding for each cladding layer. The second irradiation of the laser causes the grains in the remelting zone to grow up by heating, and the structure to coarsen [24].  Figure 7 shows the Tafel polarization curves of the Ni and Co-based composite cla ding layer and Co-based cladding layer in 3.5% NaCl solution. From Figure 7, it can observed that the cladding layer undergoes positive polarization. The Tafel extrapolat method was used to obtain the self-corrosion potential and self-corrosion current of cladding layer in 3.5% NaCl solution, and the results are shown in Table 3. The self-c rosion potential of the Co-based cladding layer is −0.896 V, and the self-corrosion curr density is 2.469 × 10 −4 A·cm −2 . The self-corrosion potential of the Ni and Co-based comp site cladding layer is −0.964 V, and the self-corrosion current density is 3.547 × 10 −4 A·cm The more positive the self-corrosion potential, the smaller the self-corrosion current d sity, the better the corrosion resistance of the clad surface. As a result, the Co-based cl ding layer has better corrosion resistance. The reasons for the increased corrosion sistance of the cladding layer are as follows: (1) After laser cladding, the C and Fe eleme in the vermicular graphite cast iron matrix enter the cladding layer to generate carbid and FeNi3 compounds, which form micro-batteries on the surface of the cladding la and lead to local corrosion. Among them, carbides are used as cathodes, and γ-Co, e are used as anodes to reduce the corrosion of the surface of the cladding layer. The gen ation of a large number of compounds in the Ni and Co-based composite cladding la will increase the self-corrosion current density and reduce the corrosion resistance. During the laser cladding process, the metal elements such as Co, Cr, Ni, and Fe will p duce bias separation during solidification, causing the inhomogeneous structure. Mor ver, at the same time, different phases are generated between grains and grain boundari resulting in potential differences and the formation of micro-batteries. It can be seen fr the microstructure SEM of Table 2 that the Ni and Co-based composite cladding layer h more C and Cr elements at the grain boundary, and the Co-based cladding layer conta more Co elements, so the Co-based cladding layer has better corrosion resistance. (3) NaCl solution, Cl atoms are easily deposited in the defects such as holes and cracks on surface of the cladding layer, which will destroy the oxide film formed on the surface the cladding layer, and Cl atoms will further migrate to the defects, corrode the cladd layer and reduce the corrosion resistance of the cladding layer. Compared with defe such as cracks on the surface of the Ni and Co-based composite cladding layer, the surf of the Co-based cladding layer is better, the probability of local micro-battery is reduc and the corrosion resistance is better [25]. (4) Elements such as Co, Ni, and Cr are pass ated to produce a dense oxide film, generating a passivated phase and increasing the ov all electrode potential of the cladding layer [26]. The corrosive medium of NaCl is eff tively isolated from the surface of the cladding layer, acting as a corrosion barrier to p vent further corrosion of the surface of the cladding layer and improve the corrosion  Figure 7 shows the Tafel polarization curves of the Ni and Co-based composite cladding layer and Co-based cladding layer in 3.5% NaCl solution. From Figure 7, it can be observed that the cladding layer undergoes positive polarization. The Tafel extrapolation method was used to obtain the self-corrosion potential and self-corrosion current of the cladding layer in 3.5% NaCl solution, and the results are shown in Table 3. The self-corrosion potential of the Co-based cladding layer is −0.896 V, and the self-corrosion current density is 2.469 × 10 −4 A·cm −2 . The self-corrosion potential of the Ni and Cobased composite cladding layer is −0.964 V, and the self-corrosion current density is 3.547 × 10 −4 A·cm −2 . The more positive the self-corrosion potential, the smaller the selfcorrosion current density, the better the corrosion resistance of the clad surface. As a result, the Co-based cladding layer has better corrosion resistance. The reasons for the increased corrosion resistance of the cladding layer are as follows: (1) After laser cladding, the C and Fe elements in the vermicular graphite cast iron matrix enter the cladding layer to generate carbides and FeNi 3 compounds, which form micro-batteries on the surface of the cladding layer and lead to local corrosion. Among them, carbides are used as cathodes, and γ-Co, etc., are used as anodes to reduce the corrosion of the surface of the cladding layer. The generation of a large number of compounds in the Ni and Co-based composite cladding layer will increase the self-corrosion current density and reduce the corrosion resistance.

Corrosion Resistance of Cladding Layer
(2) During the laser cladding process, the metal elements such as Co, Cr, Ni, and Fe will produce bias separation during solidification, causing the inhomogeneous structure. Moreover, at the same time, different phases are generated between grains and grain boundaries, resulting in potential differences and the formation of micro-batteries. It can be seen from the microstructure SEM of Table 2 that the Ni and Co-based composite cladding layer has more C and Cr elements at the grain boundary, and the Co-based cladding layer contains more Co elements, so the Co-based cladding layer has better corrosion resistance. (3) In NaCl solution, Cl atoms are easily deposited in the defects such as holes and cracks on the surface of the cladding layer, which will destroy the oxide film formed on the surface of the cladding layer, and Cl atoms will further migrate to the defects, corrode the cladding layer and reduce the corrosion resistance of the cladding layer. Compared with defects such as cracks on the surface of the Ni and Co-based composite cladding layer, the surface of the Co-based cladding layer is better, the probability of local micro-battery is reduced, and the corrosion resistance is better [25]. (4) Elements such as Co, Ni, and Cr are passivated to produce a dense oxide film, generating a passivated phase and increasing the overall electrode potential of the cladding layer [26]. The corrosive medium of NaCl is effectively isolated from the surface of the cladding layer, acting as a corrosion barrier to prevent further corrosion of the surface of the cladding layer and improve the corrosion resistance of the cladding layer.   Figure 8 shows the poor quality of the Ni and Co-based composite cladding la and the Co-based cladding layer before and after abrasion. It can be found that the Ni Co-based composite cladding layer has lower wear and better wear resistance. Figur shows the surface wear morphology of Ni and Co-based composite cladding layer a friction and wear experiments. It can be observed from Figure 9a that the Cr-Ni-Fe other phases formed in the Ni and Co-based composite cladding layer reduce hardness of the cladding layer. The hardness of the cladding layer is small and pla deformation is prone to occur, and when it is sheared the contact area of the fric surface increases, and at this time, obviously cutting appears on the wear surface of Ni and Co-based composite cladding layer. On the one hand, due to the generation frictional heat, the coating is oxidized to different degrees. As shown in Table 4 EDS, th is still a high content of O elements on the wear surface. An oxide film will be formed the friction surface, and the wear resistance will be improved accordingly. On the o hand, as the friction time progresses, wear is also progressing, the oxide film fatigues falls off, forming oxide deposits, and finally serious oxidative wear occurs on the w surface under the interaction between the wear surface and the wear part. Figure 9b sh the surface wear morphology of the Co-based cladding layer after the friction and w experiment. It can be analyzed from Figure 9b that due to the combined effects of formation of C and Cr carbides in the cobalt-based cladding layer, the hardness of cobalt-based cladding layer is relatively high. Additionally, the friction is caused by small particles falling off and the convex peaks on the high-hardness ball due to continuous collision of the micro-protrusions on the surface of the friction pair and three-body abrasive particles on the friction surface. During the reciprocating slid process, the carbide in the cladding layer will fall off and cut the surface of the sam under the influence of the normal load, resulting in a large number of furrow wear ma At the same time, fatigue wear occurs on the surface under the action of cyclic stress, the growth of surface cracks causes large pieces of material to peel off and produce w   Figure 8 shows the poor quality of the Ni and Co-based composite cladding layer, and the Co-based cladding layer before and after abrasion. It can be found that the Ni and Co-based composite cladding layer has lower wear and better wear resistance. Figure 9a shows the surface wear morphology of Ni and Co-based composite cladding layer after friction and wear experiments. It can be observed from Figure 9a that the Cr-Ni-Fe and other phases formed in the Ni and Co-based composite cladding layer reduce the hardness of the cladding layer. The hardness of the cladding layer is small and plastic deformation is prone to occur, and when it is sheared the contact area of the friction surface increases, and at this time, obviously cutting appears on the wear surface of the Ni and Co-based composite cladding layer. On the one hand, due to the generation of frictional heat, the coating is oxidized to different degrees. As shown in Table 4 EDS, there is still a high content of O elements on the wear surface. An oxide film will be formed on the friction surface, and the wear resistance will be improved accordingly. On the other hand, as the friction time progresses, wear is also progressing, the oxide film fatigues and falls off, forming oxide deposits, and finally serious oxidative wear occurs on the wear surface under the interaction between the wear surface and the wear part. Figure 9b shows the surface wear morphology of the Co-based cladding layer after the friction and wear experiment. It can be analyzed from Figure 9b that due to the combined effects of the formation of C and Cr carbides in the cobalt-based cladding layer, the hardness of the cobalt-based cladding layer is relatively high. Additionally, the friction is caused by the small particles falling off and the convex peaks on the high-hardness ball due to the continuous collision of the micro-protrusions on the surface of the friction pair and the three-body abrasive particles on the friction surface. During the reciprocating sliding process, the carbide in the cladding layer will fall off and cut the surface of the sample under the influence of the normal load, resulting in a large number of furrow wear marks. At the same time, fatigue wear occurs on the surface under the action of cyclic stress, and the growth of surface cracks causes large pieces of material to peel off and produce wear debris. In addition, a large amount of friction heat is easily generated during wear, and the temperature rises instantly. As shown in Table 4 EDS, the content of O elements in the wear zone is high, and oxide film is easily formed on wear, and the oxide film is easily destroyed by wear debris. At this time, the main wear mechanism is abrasive wear and slight oxidative wear. However, the wear amount of the Ni and Co-based composite cladding layer is relatively small. This is because the contact area of the worn surface is further increased, which will produce an obvious smooth layer [27], which changes the interaction of the worn surface. The work hardened layer [28] produced on the wear surface makes the wear surface have higher load-bearing capacity and wear resistance. As the frictional heat and the contact area of the friction surface increase, the probability that the friction surface combines with oxygen increases, and the oxide deposits increase. The force direction expands, forming a new smooth layer on the surface. It can be found from the analysis in Table 4 that the friction surface is mainly oxides of O, Co, and Cr, and the combined oxides of Cr and Co are easy to sinter to form an enamel layer at high temperatures [29], which can significantly reduce the amount of wear. debris. At this time, the main wear mechanism is abrasive wear and slight oxidative wear. However, the wear amount of the Ni and Co-based composite cladding layer is relatively small. This is because the contact area of the worn surface is further increased, which will produce an obvious smooth layer [27], which changes the interaction of the worn surface.

Wear Performance of Cladding Layer
The work hardened layer [28] produced on the wear surface makes the wear surface have higher load-bearing capacity and wear resistance. As the frictional heat and the contact area of the friction surface increase, the probability that the friction surface combines with oxygen increases, and the oxide deposits increase. The force direction expands, forming a new smooth layer on the surface. It can be found from the analysis in Table 4 that the friction surface is mainly oxides of O, Co, and Cr, and the combined oxides of Cr and Co are easy to sinter to form an enamel layer at high temperatures [29], which can significantly reduce the amount of wear.    debris. At this time, the main wear mechanism is abrasive wear and slight oxidative wear. However, the wear amount of the Ni and Co-based composite cladding layer is relatively small. This is because the contact area of the worn surface is further increased, which will produce an obvious smooth layer [27], which changes the interaction of the worn surface. The work hardened layer [28] produced on the wear surface makes the wear surface have higher load-bearing capacity and wear resistance. As the frictional heat and the contact area of the friction surface increase, the probability that the friction surface combines with oxygen increases, and the oxide deposits increase. The force direction expands, forming a new smooth layer on the surface. It can be found from the analysis in Table 4 that the friction surface is mainly oxides of O, Co, and Cr, and the combined oxides of Cr and Co are easy to sinter to form an enamel layer at high temperatures [29], which can significantly reduce the amount of wear.      Figure 10 shows the load-displacement curve of the indenter applied to the top of the sample when the cladding layer is separated from the cast iron matrix after the shear test is measured, and the shear bond strength is measured by the shear measurement method. As shown in Figure 11, the shear bonding strength of the laser cladding nickel-based cladding layer is about 480 MPa, and the shear bonding strength of the laser cladding nickel-based and cobalt-based composite cladding layer is about 387.5 MPa. It can be seen from the macro-photograph of the shear specimen in Figure 12 that the cladding layer has a higher bonding strength, and the fracture position of the cladding layer is on the base material. There is a difference in the shear strength of the fracture in the position of the base metal, which is because the thermal cycle of the laser cladding process affects the strength of the base metal. What is more, the integrity of the ring after the shear failure of sample 1 is obviously better than that of sample 2. Through analysis, it can be found that the surface of the cladding layer prepared by laser cladding on vermicular graphite cast iron RT450 has no defects such as pores and cracks, and the bonding strength of the laser cladding layer is higher than that of the base material.
Coatings 2021, 11, x FOR PEER REVIEW Figure 10 shows the load-displacement curve of the indenter applied to sample when the cladding layer is separated from the cast iron matrix after is measured, and the shear bond strength is measured by the shear measure As shown in Figure 11, the shear bonding strength of the laser cladding nick ding layer is about 480 MPa, and the shear bonding strength of the laser cla based and cobalt-based composite cladding layer is about 387.5 MPa. It can the macro-photograph of the shear specimen in Figure 12 that the claddin higher bonding strength, and the fracture position of the cladding layer material. There is a difference in the shear strength of the fracture in the p base metal, which is because the thermal cycle of the laser cladding proc strength of the base metal. What is more, the integrity of the ring after the s sample 1 is obviously better than that of sample 2. Through analysis, it can the surface of the cladding layer prepared by laser cladding on vermicular iron RT450 has no defects such as pores and cracks, and the bonding streng cladding layer is higher than that of the base material.

Conclusions
(1) The self-corrosion potentials of the Co-based cladding layer and the Ni an composite cladding layers are −0.896V and −0.964V, respectively, and th sion current density is 2.469 × 10 −4 A·cm −2 and 3.547 × 10 −4 A·cm −2 . Due to geneity of the material and the structure and the potential difference elements, the micro-batteries are formed. Compared with the Ni and Co posite cladding layer, the surface of the Co-based cladding layer has bett resistance.

Conclusions
(1) The self-corrosion potentials of the Co-based cladding layer and the Ni and Cobased composite cladding layers are −0.896V and −0.964V, respectively, and the self-corrosion current density is 2.469 × 10 −4 A·cm −2 and 3.547 × 10 −4 A·cm −2 . Due to the inhomogeneity of the material and the structure and the potential difference between the elements, the micro-batteries are formed. Compared with the Ni and Co-based composite cladding layer, the surface of the Co-based cladding layer has better corrosion resistance. (2) The wear of Ni and Co-based composite cladding layer is 0.72 times higher than that of Co-based cladding layers due to the combination of different compounds generated by the different elemental contents and the different degrees of plastic deformation, fatigue wear, and oxidative wear occurring on the surface of the cladding layers.