Hall Amplifier Nanoscale Device (HAND): Modeling, Simulations and Feasibility Analysis for THz Sensor

HAND (Hall Amplifier Nanoscale Device), a new nano-metric device, was designed, simulated, and modeled for feasibility analysis, with the challenge of combining a well-known macro effect into the nanoscale world. HAND is based on the well-known Hall Effect, and it may enable circuitry working at very high frequencies (tens of Tera-Hertz). The architecture, design, and simulations were performed while using Comsol Multi-Physics Package Software. Complementary accurate analytical models were developed to support the understanding of the device functionality, including treatment of specific phenomena, such as heat transfer, and mega-magnet feasibility inside integrated circuits. This new device, combining both the Hall Effect and nanoscale dimensions, holds the potential to change the computing rates in the microelectronics circuitry world, and can serve as a game changer.


Introduction
The Hall Amplifier is a well-known and established phenomenon since it was discovered by Edwin Hall in 1879 [1]. The Hall Effect is the production of a voltage difference (the Hall Voltage) across an electrical conductor, transverse to an electric current in the conductor, and to an applied magnetic field perpendicular to the current. As electrons travel through the conductor that lies in a magnetic Field B, the electrons will experience a magnetic force. This magnetic force will cause the electrons to travel closer to one side than the other, creating a negative charge on one side and a positive on the other. This separation of charge creates a voltage difference that is known as the Hall Voltage. Electrons move in the Y direction and an electric field component appears in the Y direction E Y . This will continue until the Lorentz force is equal and opposite to the electric force due to the buildup of electrons-that is, a steady condition arises. The voltage builds up until the electric field produces an electric force on the charges that is equal and opposite of the magnetic force. This effect is known as the Hall Effect, which can be used to distinguish the currents that are composed of positively charged particles from those that are composed of negatively charged particles, as emphasized by Lorentz [2]. With time, the idea of using and moving the Hall Effect from the macro to micro and nano scales caught the attention of various research initiatives. Several types of devices sharing Hall Effect were studied thoroughly in the past decade, such as MoS 2 transistors [3] and Hall Effect sensors [4]. Moving forward with electromagnetic fields in circuitry, Ballistic deflection transistors were also studied [5]. In those cases, the ballistic effects in transistors were also examined [6][7][8].
As mentioned above, the notion of designing a Hall Amplifier is not new and it has already existed for six decades [9][10][11]. In fact, a double challenge exists: Time review and Technology capability.
As mentioned above, the notion of designing a Hall Amplifier is not new and it has already existed for six decades [9][10][11]. In fact, a double challenge exists: Time review and Technology capability. From the time point of view, the idea of Hall Effect amplifiers seems to be hidden in very old and hardly accessible papers, as cited above. From the technology point of view, the implementation of these early ideas has been difficult or even impossible due to the lack of suitable materials and technologies. Such materials and technologies are currently emerging and, therefore, a re-examination of the entire concept appears mandatory.
Our innovation is to try to design a nanoscale device that can be integrated in circuits. The goal is to find out whether the existing nanotechnology and contemporary capability to make extremely small and complex devices can be used to advance the state of art in high frequency electronics. In particular, our goal is to obtain amplifiers and sources in THz frequencies. Moreover, and in contrast to regular transistors that work with voltage as input and with current as output, the Hall Amplifier works differently-i.e., with current as an input and voltage as output. This characteristic could lead to different applications, and if such a device is achieved it would indeed be revolutionary. We explore an alternative with magnetic fields contrary to past research of ballistic deflation devices in which the deflection was conducted with an electrical field. This article presents the architecture, design, modeling, and simulations of a Hall Amplifier Nanoscale Device, the HAND.

Nanoscale Device Concept and Advantages
Starting from the schematic design of the Hall Amplifier device, as presented in Figure 1, we progressed with a translation of the concept into a well-defined structure in numerical application. The structure of the device is made of a Hall Bar and of an electro magnet close to it. By parameterizing the simulation dimensions, the bar voltage and current, it would be easier to study different parameters and their physical effect on the Hall Bar as a trans-impedance amplifier and its frequency response. The expected outcome of such a study is to analyze the materials and dimensions that should be used to make this device operational at THz frequencies. Undoubtedly, a successful accomplishment of this challenge can enable clear nano-technological advantages. Operating the Hall Bar at AC conditions and measuring output power was done before, but the real question is whether nanotechnology can be used to actually produce a device from this concept. It is not a simple question to answer, however using a simulation environment seems to be very helpful.

Device Architecture and Design
The design of the HAND consists of copper coil surrounding the Hall Bar, which is made of doped GaAs, as shown in Figure 2. In more advanced simulations, and after other materials like silicon were tested, the Hall Bar was chosen to be made of doped GaAs because it has high mobility. Comsol Multi-Physics uses the Finite Element method [12,13], which is a numerical method for solving partial differential equations by domain discretization.
As part of HAND's preliminary design, a bent rear bar shape was chosen for boundary conditions and smooth and convenient usage, when simulating with the Comsol software package. HAND's final shape towards its fabrication will be optimized according to process guidelines and limitations. Figure 3 presents the design of the device for simulation purpose. The main concept is to run electric current through the coil which surrounds the Hall Bar, thus creating a magnetic field inside the Hall Bar, resulting in a voltage between the two knobs of the Hall Bar, due to the Hall Effect. The width of the bar is 50 nm. Yet, the simulation model was built up in a way that allows for quick changes in all dimensions.

Device Architecture and Design
The design of the HAND consists of copper coil surrounding the Hall Bar, which is made of doped GaAs, as shown in Figure 2. In more advanced simulations, and after other materials like silicon were tested, the Hall Bar was chosen to be made of doped GaAs because it has high mobility. Comsol Multi-Physics uses the Finite Element method [12,13], which is a numerical method for solving partial differential equations by domain discretization. As part of HAND's preliminary design, a bent rear bar shape was chosen for boundary conditions and smooth and convenient usage, when simulating with the Comsol software package. HAND's final shape towards its fabrication will be optimized according to process guidelines and limitations. Figure 3 presents the design of the device for simulation purpose. The main concept is to run electric current through the coil which surrounds the Hall Bar, thus creating a magnetic field inside the Hall Bar, resulting in a voltage between the two knobs of the Hall Bar, due to the Hall Effect. The width of the bar is 50 nm. Yet, the simulation model was built up in a way that allows for quick changes in all dimensions.

Device Architecture and Design
The design of the HAND consists of copper coil surrounding the Hall Bar, which is made of doped GaAs, as shown in Figure 2. In more advanced simulations, and after other materials like silicon were tested, the Hall Bar was chosen to be made of doped GaAs because it has high mobility. Comsol Multi-Physics uses the Finite Element method [12,13], which is a numerical method for solving partial differential equations by domain discretization. As part of HAND's preliminary design, a bent rear bar shape was chosen for boundary conditions and smooth and convenient usage, when simulating with the Comsol software package. HAND's final shape towards its fabrication will be optimized according to process guidelines and limitations. Figure 3 presents the design of the device for simulation purpose. The main concept is to run electric current through the coil which surrounds the Hall Bar, thus creating a magnetic field inside the Hall Bar, resulting in a voltage between the two knobs of the Hall Bar, due to the Hall Effect. The width of the bar is 50 nm. Yet, the simulation model was built up in a way that allows for quick changes in all dimensions.

Simulation Considerations
The design and the simulations of all the devices in the research group are performed while using the Comsol Multi-Physics Software Package [14]. In this specific case, the required simulation models are the AC/DC module and the semiconductors module. As shown in Figure 3, the materials that were simulated in this model are metals with high conductivity in the front panel. In addition to Comsol, Matlab software [15] for mathematical modeling of the device behavior was also used. Figures 4 and 5 present the mesh considerations.
law and electric potential. The second module that used for the analyses is the Heat Transfer one, whose main features are the electric current and heat transfer providing the joule heating process.

Mesh Accuracy and Considerations
The geometries of the Hall Bar and the coil are discretized in squares to achieve the most accurate results for their block symmetry. The discretization of the Hall Bar's output knobs is denser to obtain more accurate results. The remaining geometry is discretized in tetrahedron, which is the default mesh. The mesh used in the 2D simulation is the default mesh, and it is different from the 3D one. The chosen element size option was "extra fine".

Classical Hall Effect
The following are well-known equations and assumptions that serve as the mathematical basis to formulate the classical Hall Effect, when compared to updated models, and nanoscale whose main features are the electric current and heat transfer providing the joule heating process.

Mesh Accuracy and Considerations
The geometries of the Hall Bar and the coil are discretized in squares to achieve the most accurate results for their block symmetry. The discretization of the Hall Bar's output knobs is denser to obtain more accurate results. The remaining geometry is discretized in tetrahedron, which is the default mesh. The mesh used in the 2D simulation is the default mesh, and it is different from the 3D one. The chosen element size option was "extra fine".

Classical Hall Effect
The following are well-known equations and assumptions that serve as the mathematical basis to formulate the classical Hall Effect, when compared to updated models, and nanoscale As presented below, in Figures 6-20, tens of simulations were performed while using the Comsol Multi-Physics Package Software. It was necessary to combine the usage of several modules in order to simulate such complex analyses. The first module used is the AC/DC, whose features are the (1) Magnetic and Electric Fields (MEF), providing the magnetic field by using Ampere's Law, and electric field by Current conservation, and the (2) Electric Currents (EC), providing the current conservation law and electric potential. The second module that used for the analyses is the Heat Transfer one, whose main features are the electric current and heat transfer providing the joule heating process.

Single Loop Copper Wire Magnetic Field
As the electric current goes through the copper coil, it creates a magnetic field around the coil by Ampere's Law. Figure 6 shows the magnetic flux density norm (T) is distributed in our geometry. The direction of the magnetic field goes into the Hall Bar. The simulations were conducted with input electric current of 30 µA and 30 mA, called I0 which is the DC input current inserted in Comsol calculations, and which will serve later as the amplitude of an AC input signal. Different copper coil radii were chosen, ranging from 15 nm to 40 nm (CW). Additionally, the distance between the center of the Hall Bar to the center of the coil varies between 70 nm and 100 nm (CD). As predicted, the magnetic field is stronger as the coil distance (CD) gets smaller, as demonstrated in Figure 7a-e. The max magnetic field varies between 0.47 T and 0.54 T. The magnetic field around the Hall Bar is between 0.2 T and 0.25 T.

Multi-Loop Copper Wire Magnetic Field
Multi-loop coil could potentially produce stronger magnetic fields, thus obtaining stronger Hall Voltage output. The input electric current that was used in these simulations is 30 µA. As predicted, the magnetic field gets stronger as the number of loops increases (Figures 9-12). The magnetic field is more uniform around the Hall Bar than it was in the single loop coil. The max magnetic field is in the range of 1.49 mT to 2 mT. In case the input electric current becomes 30 mA (instead of 30 µA), the maximal value of the magnetic field will be in the range of 1.49 T to 2 T. The magnetic field becomes more uniform as the number of loops increases.

Heat Transfer of the Device
Electric current through a wire produces heat by joule heating. Temperature adds more noise to the system, and the goal in these simulations is to find the temperature around the Hall Bar. The Hall Bar in these simulations is made of GaAs. The heat transfer coefficient that was used in these simulations is 100 , as shown in Figure 13. It is the heat transfer coefficient for forced convection; moderate speed flow of air over a surface [19]. The dimensions of the HAND for these simulations are as shown in Figure 6. As shown in Figures 13 and 14, as the current gets bigger the temperature gets higher. The temperature ranges between 337 K and 413 K. If the input electric current is 30 mA-50 mA the temperature could elevate to two to three orders of magnitude higher than the current simulation; therefore, cooling is required to make the HAND feasible.

Heat Transfer of the Device
Electric current through a wire produces heat by joule heating. Temperature adds more noise to the system, and the goal in these simulations is to find the temperature around the Hall Bar. The Hall Bar in these simulations is made of GaAs. The heat transfer coefficient that was used in these simulations is 100 , as shown in Figure 13. It is the heat transfer coefficient for forced convection; moderate speed flow of air over a surface [19]. The dimensions of the HAND for these simulations are as shown in Figure 6. As shown in Figures 13 and 14, as the current gets bigger the temperature gets higher. The temperature ranges between 337 K and 413 K. If the input electric current is 30 mA-50 mA the temperature could elevate to two to three orders of magnitude higher than the current simulation; therefore, cooling is required to make the HAND feasible. Figure 13. The temperature as a function of the input electric current. Figure 13. The temperature as a function of the input electric current.

Current Density Effect on Joule Heating
As the current density becomes higher, the heat that is produced by joule heating increases. As predicted, the temperature declines as the current density decreases, as shown in Figure 15a-e.

Hall Bar 2D AC/DC Simulations
In the 2D simulation, the magnetic field that was used was defined by B ⃗ (t) = B e z . This magnetic field should be the same magnetic field that could be produced by AC electric current through the copper coil. The magnetic field that was produced by the electric current in the 3D simulation was not used in the 2D simulation. This magnetic field B ⃗ (t) is perpendicular to the Hall Bar. In the Hall Bar there is a DC electric current I in the X direction, so the Hall Effect produces a Hall Voltage between the two output knobs of the Hall Bar, as shown in Figure 16. In the DC magnetic field, the output voltage is highest in steady state, when there is no electric current I in the Y direction. Figure 16. Simulation of the voltage difference across the Hall Bar that is caused by the perpendicular magnetic field.

Frequency Effect on Hall Voltage
The Hall Voltage stays constant VHall = 2.1 mV until f = 400 GHz, and then it starts to decrease to zero around. f = 8.10 13 Hz, as shown in Figure 17.

The Effect of the Applied Voltage Vdd on Hall Voltage
A higher Vdd means a stronger electric field in the X direction, which causes higher electric current in the X direction. If this current increases in DC, the equilibrium between the Lorentz force

The Effect of the Applied Voltage Vdd on Hall Voltage
A higher Vdd means a stronger electric field in the X direction, which causes higher electric current in the X direction. If this current increases in DC, the equilibrium between the Lorentz force (magnetic field) to the Coulomb force (electric field in Y direction) will be achieved at a higher Hall Voltage. The same happens in AC, as Vdd gets bigger; the Hall Voltage between the Hall Bar knobs increases, as shown in Figure 18.

The Effects of Scattering Time on the Hall Voltage
This simulation depicts the effects of scattering time on the frequency response; therefore, different scattering times were chosen. In reality, different materials will be chosen or different doping in each material, which will change the scattering time due to impurities scattering, as can be seen by Matthiessen's rule: The Hall Bar is made of Copper in this simulation.
It is important to note that this simulation uses the Drude model for free electron and it does not take the ballistic effect or quantum effects into account.
The assumption that was used in this simulation is that the scattering time τ is proportional to the electron mobility and the electrical conductivity, meaning: σ ∝ μ ∝ τ (74) This means that as the scattering time decreases the electron mobility and the electrical conductivity decreases. As τ gets lower, the device can work for higher frequencies, but the overall Hall Voltage also decreases. For τ = 0.36 × 10 −16 s, the HAND can work at frequencies up to f = 200 THz, but the Hall Voltage is much smaller than in the case of τ = 3.6 × 10 −14 s, as shown in Figure 19.

Heterodyne Hall Effect Simulation
In conclusion, we obtained preliminary results for this simulation, but more research is required. In this simulation, the Hall Bar is doped Silicon. In Figure 20, there appears to be resonant frequency around 2.1 GHz where the output voltage is 45 mV. The HAND's behavior in this model is different when compared to the approximation that was made in the dynamic magneto-resistance model.

Accuracy
A better understanding of the physical model is required in order to achieve a more accurate simulation. In the heterodyne Hall Effect simulation, the result was different as compared to the approximation that was made in the dynamic conductivity model. More research is required for a better understanding of the heterodyne model. Moreover, the quantum Hall Effect model might be required to receive accurate results.
In the other simulations, the Hall Bar is made of copper and the scattering time of copper is in the range of femtoseconds, meaning τ = 36 × 10 −15 s [20], and the simulations run for lower scattering time up to τ = 0.36 × 10 −15 s, as shown in Figure 15. The simulations show that the HAND can work for up to f = 200 THz for a lower scattering time, but as τ gets lower, the Hall Voltage, overall, also gets smaller. Hence, there is a tradeoff between higher amplification to higher frequencies. More research is required for a better understanding of this device. One can note that the required feasibility is not about the frequency response. It is quite clear that this device (like any other electronic device) works faster as we scale it down. It is our plan to continue developing the mathematical model and the simulations since a first generation of this device did not show the expected high frequencies. The question is whether we can really scale down the device that was invented 140 years ago. Almost the same material was used, as we do (high mobility III-V), but then a huge electromagnet was probably used to drive the device (completely isolated from the bar itself). We obviously cannot use such a magnet in a nano-device, so the question remains as to whether we can operate the device with a single lap electromagnet. Currently, we are quite convinced that for DC the answer is no, but in AC and using a differential mode it might work. On the chip there are devices that are designed to operate at differential mode, but we came across the isolation issue as we tried to measure it: that is, we are not sure that the input and output can share the same ground in this device (like common source in standard transistor).
Our actual perspective is that a lot of know how to this device should come from the field of superconductors (which has to be current driven), but this idea is yet to be investigated. Intuitively, with all of the low temperature electronic surrounding us for quantum computing, perhaps the right

Mesh Accuracy and Considerations
The geometries of the Hall Bar and the coil are discretized in squares to achieve the most accurate results for their block symmetry. The discretization of the Hall Bar's output knobs is denser to obtain more accurate results. The remaining geometry is discretized in tetrahedron, which is the default mesh. The mesh used in the 2D simulation is the default mesh, and it is different from the 3D one. The chosen element size option was "extra fine".

Classical Hall Effect
The following are well-known equations and assumptions that serve as the mathematical basis to formulate the classical Hall Effect, when compared to updated models, and nanoscale considerations developed later on in this study. It is necessary to return to the electromagnetism basics before analyzing more complex case studies. Assuming: Subsequently, we get: Also: Since: We obtain: Since: We get: where: L y is the transverse width of the Hall Bar, A x is the transverse cross sectional area of Hall Bar, v D is the drift velocity, B Z is the magnetic field in the Z direction, E Y is the electric field in the Y direction, V H is the Hall Voltage, V Y is the voltage in the Y direction, I x is the electric current in the Hall Bar, e is the electron charge (1.6 × 10 −19 C), n is the particle density, and R H is the 3D Hall coefficient.

DC Hall Magneto-Resistance
The Drude model [16] provides an estimate for the resistance. This model can be applied where a precise understanding of scattering is not required. The equation of motion for the momentum per electron is as follows: where: p = momentum per electron, τ = collision time (mean free time), and F = external force. The Hall Effect changes the electrical resistance of the material by using externally-applied magnetic field. Initially, the velocity of the electrons is: The electric field is: (12) and the magnetic field is: Accordingly, the equation of motion is: where m e is the effective mass of the electron. In the case of DC electrical conductivity, we obtain the two following equations: In steady state condition: where: ω c = eB z m e (19) is the cyclotron frequency.
In steady state, since: v y = 0 (20) Subsequently: Therefore: Since: The two-dimensional (2D)-Hall coefficient is defined as: The Hall magneto-resistance is defined as: meaning that the resistance does not depend on the shape of the Hall Bar.
In the presence of magnetic field, the resistivity tensor becomes: Therefore: The conductivity tensor is: Therefore: σ xx σ xy σ yx σ yy = ρ xx ρ xy ρ yx ρ yy where:

Approximation to the Dynamic Magneto-Conductivity Tensor for Free Electrons
At this stage, it was necessary to develop a new approach for a specific case study of weak magnetic field acting on a small input signal, which means creating small amplification. The Dynamic magneto-conductivity tensor for free electrons in the case of oscillating magnetic field in the Z direction, such as → B(t) = B 0 e −iωtẑ , and static electric field in the X direction, will be calculated by using Perturbation Theory. Additionally, this model uses the assumptions of the Drude model as shown in the DC Hall magneto-resistance section above, therefore the ballistic conductance is not taken into account in this model. Moreover, this model does not include quantum hall effect, which becomes relevant for strong magnetic fields B > 0.5 T. The equations of motion, for the momentum per electron, are as follows: and For zero order ε 0 , the equation becomes: Since → E is static, we get d Therefore: From that, we get: For zero order ε 1 the equation becomes: Therefore: Since Since For zero order ε 2 the equation becomes: and Therefore and

Heterodyne Hall Effect in a Two-Dimensional Electron Gas
The Hall Effect with a magnetic and electric field oscillating in time with resonant frequencies is a phenomenon that realizes an example of heterodyne device with the magnetic field acting as a driving and it is analyzed in detail in its classical versions while using Floquet theory [17]. A bulk current flowing perpendicularly to the applied electric field is found, with a frequency shifted by integer multiples of the driving frequency. The heterodyne conductivity [17] σ m,n ab , introduced here for classical case, is a four index tensor implicitly that is defined by the linear relation that holds between the electric current density j a (mΩ) of the output signal with frequency mΩ, flowing along the a-direction (a, b = x, y, z) and the weak electric field E n b along the b-direction with frequency nΩ.
It can be shown that the classical case the heterodyne conductivity for n = 0 (static electric field) [17] is: where Ω is the magnetic field frequency, ω c is the cyclotron frequency, J 0 (r) is zero order Bessel function, J 1 (r) is first order Bessel function, and r = ω c Ω is the Bessel function argument.

Dielectric Tensor for Free Electron Model
From the Maxwell equation, the dielectric function tensor of the medium is related to the conductivity tensor, as: Therefore

Parameters
Preliminary results were obtained. The parameters used for the 2D simulations are presented in Table 1.

Single Loop Copper Wire Magnetic Field
As the electric current goes through the copper coil, it creates a magnetic field around the coil by Ampere's Law. Figure 6 shows the magnetic flux density norm (T) is distributed in our geometry. The direction of the magnetic field goes into the Hall Bar. The simulations were conducted with input electric current of 30 µA and 30 mA, called I0 which is the DC input current inserted in Comsol calculations, and which will serve later as the amplitude of an AC input signal. Different copper coil radii were chosen, ranging from 15 nm to 40 nm (CW). Additionally, the distance between the center of the Hall Bar to the center of the coil varies between 70 nm and 100 nm (CD). As predicted, the magnetic field is stronger as the coil distance (CD) gets smaller, as demonstrated in Figure 7a

Multi-Loop Copper Wire Magnetic Field
Multi-loop coil could potentially produce stronger magnetic fields, thus obtaining stronger Hall Voltage output. The input electric current that was used in these simulations is 30 µA. As predicted, the magnetic field gets stronger as the number of loops increases (Figures 9-12). The magnetic field is more uniform around the Hall Bar than it was in the single loop coil. The max magnetic field is in the range of 1.49 mT to 2 mT. In case the input electric current becomes 30 mA (instead of 30 µA), the maximal value of the magnetic field will be in the range of 1.49 T to 2 T. The magnetic field becomes more uniform as the number of loops increases.

Heat Transfer of the Device
Electric current through a wire produces heat by joule heating. Temperature adds more noise to the system, and the goal in these simulations is to find the temperature around the Hall Bar. The Hall Bar in these simulations is made of GaAs. The heat transfer coefficient that was used in these simulations is 100 W m 2 K , as shown in Figure 13. It is the heat transfer coefficient for forced convection; moderate speed flow of air over a surface [19]. The dimensions of the HAND for these simulations are as shown in Figure 6.
As shown in Figures 13 and 14, as the current gets bigger the temperature gets higher. The temperature ranges between 337 K and 413 K. If the input electric current is 30 mA-50 mA the temperature could elevate to two to three orders of magnitude higher than the current simulation; therefore, cooling is required to make the HAND feasible.

Current Density Effect on Joule Heating
As the current density becomes higher, the heat that is produced by joule heating increases. As predicted, the temperature declines as the current density decreases, as shown in Figure 15a-e.

Hall Bar 2D AC/DC Simulations
In the 2D simulation, the magnetic field that was used was defined by → B(t) = B z e −iωtẑ . This magnetic field should be the same magnetic field that could be produced by AC electric current through the copper coil. The magnetic field that was produced by the electric current in the 3D simulation was not used in the 2D simulation. This magnetic field → B(t) is perpendicular to the Hall Bar. In the Hall Bar there is a DC electric current I x in the X direction, so the Hall Effect produces a Hall Voltage between the two output knobs of the Hall Bar, as shown in Figure 16. In the DC magnetic field, the output voltage is highest in steady state, when there is no electric current I y in the Y direction.

Frequency Effect on Hall Voltage
The Hall Voltage stays constant V Hall = 2.1 mV until f = 400 GHz, and then it starts to decrease to zero around. f = 8.10 13 Hz, as shown in Figure 17.

The Effect of the Applied Voltage V dd on Hall Voltage
A higher V dd means a stronger electric field in the X direction, which causes higher electric current in the X direction. If this current increases in DC, the equilibrium between the Lorentz force (magnetic field) to the Coulomb force (electric field in Y direction) will be achieved at a higher Hall Voltage. The same happens in AC, as V dd gets bigger; the Hall Voltage between the Hall Bar knobs increases, as shown in Figure 18.

The Effects of Scattering Time on the Hall Voltage
This simulation depicts the effects of scattering time on the frequency response; therefore, different scattering times were chosen. In reality, different materials will be chosen or different doping in each material, which will change the scattering time due to impurities scattering, as can be seen by Matthiessen's rule: The Hall Bar is made of Copper in this simulation.
It is important to note that this simulation uses the Drude model for free electron and it does not take the ballistic effect or quantum effects into account.
The assumption that was used in this simulation is that the scattering time τ is proportional to the electron mobility and the electrical conductivity, meaning: This means that as the scattering time decreases the electron mobility and the electrical conductivity decreases. As τ gets lower, the device can work for higher frequencies, but the overall Hall Voltage also decreases. For τ = 0.36 × 10 −16 s, the HAND can work at frequencies up to f = 200 THz, but the Hall Voltage is much smaller than in the case of τ = 3.6 × 10 −14 s, as shown in Figure 19.

Heterodyne Hall Effect Simulation
In conclusion, we obtained preliminary results for this simulation, but more research is required. In this simulation, the Hall Bar is doped Silicon. In Figure 20, there appears to be resonant frequency around 2.1 GHz where the output voltage is 45 mV. The HAND's behavior in this model is different when compared to the approximation that was made in the dynamic magneto-resistance model. Additionally, it seems that the HAND acts as high pass filter (HPF) in this physical model (see Figure 20). The output voltage stabilizes around 5 mV after the resonant frequency.

Accuracy
A better understanding of the physical model is required in order to achieve a more accurate simulation. In the heterodyne Hall Effect simulation, the result was different as compared to the approximation that was made in the dynamic conductivity model. More research is required for a better understanding of the heterodyne model. Moreover, the quantum Hall Effect model might be required to receive accurate results.
In the other simulations, the Hall Bar is made of copper and the scattering time of copper is in the range of femtoseconds, meaning τ = 36 × 10 −15 s [20], and the simulations run for lower scattering time up to τ = 0.36 × 10 −15 s, as shown in Figure 15. The simulations show that the HAND can work for up to f = 200 THz for a lower scattering time, but as τ gets lower, the Hall Voltage, overall, also gets smaller. Hence, there is a tradeoff between higher amplification to higher frequencies. More research is required for a better understanding of this device. One can note that the required feasibility is not about the frequency response. It is quite clear that this device (like any other electronic device) works faster as we scale it down. It is our plan to continue developing the mathematical model and the simulations since a first generation of this device did not show the expected high frequencies. The question is whether we can really scale down the device that was invented 140 years ago. Almost the same material was used, as we do (high mobility III-V), but then a huge electromagnet was probably used to drive the device (completely isolated from the bar itself). We obviously cannot use such a magnet in a nano-device, so the question remains as to whether we can operate the device with a single lap electromagnet. Currently, we are quite convinced that for DC the answer is no, but in AC and using a differential mode it might work. On the chip there are devices that are designed to operate at differential mode, but we came across the isolation issue as we tried to measure it: that is, we are not sure that the input and output can share the same ground in this device (like common source in standard transistor).