Photocatalysts Based on Graphite-like Carbon Nitride with a Low Content of Rhodium and Palladium for Hydrogen Production under Visible Light

In this study, we proposed photocatalysts based on graphite-like carbon nitride with a low content (0.01–0.5 wt.%) of noble metals (Pd, Rh) for hydrogen evolution under visible light irradiation. As precursors of rhodium and palladium, labile aqua and nitrato complexes [Rh2(H2O)8(μ-OH)2](NO3)4∙4H2O and (Et4N)2[Pd(NO3)4], respectively, were proposed. To obtain metallic particles, reduction was carried out in H2 at 400 °C. The synthesized photocatalysts were studied using X-ray diffraction, X-ray photoelectron spectroscopy, UV–Vis diffuse reflectance spectroscopy and high-resolution transmission electron microscopy. The activity of the photocatalysts was tested in the hydrogen evolution from aqueous and aqueous alkaline solutions of TEOA under visible light with a wavelength of 428 nm. It was shown that the activity for the 0.01–0.5% Rh/g-C3N4 series is higher than in the case of the 0.01–0.5% Pd/g-C3N4 photocatalysts. The 0.5% Rh/g-C3N4 sample showed the highest activity per gram of catalyst, equal to 3.9 mmol gcat–1 h–1, whereas the most efficient use of the metal particles was found over the 0.1% Rh/g-C3N4 photocatalyst, with the activity of 2.4 mol per gram of Rh per hour. The data obtained are of interest and can serve for further research in the field of photocatalytic hydrogen evolution using noble metals as cocatalysts.


Introduction
Due to the growth of economic and environmental problems associated with the use of fossil fuels [1,2], the demand for a transition to alternative energy is growing [3]. Particular attention should be paid to hydrogen as a replacement for traditional energy sources [4]. Hydrogen is an environmentally friendly fuel and does not emit toxic compounds during combustion [5]. One of the most well-known processes for producing hydrogen used in industry is steam reforming of natural gas [6]. Despite the efficiency of hydrogen production of this method, steam reforming is not an environmentally friendly process, since it is energy-consuming, carried out at high temperatures and pressures and does not exclude CO 2 emissions [7]. In this regard, photocatalytic hydrogen production is of particular interest [8,9]. In the 1970s, photocatalytic hydrogen production was first discovered by Fujishima and Honda by water splitting on semiconductor photocatalysts under light irradiation [10]. Solar energy is universal, and its reserves are unlimited [11], while photocatalytic hydrogen production is a process occurring under environmental conditions [12][13][14]. Thus, photocatalytic hydrogen production can be an effective solution for converting solar energy into hydrogen energy [8].

g-C 3 N 4 Synthesis
The proposed method for the synthesis of g-C 3 N 4 consists of the thermolysis of the supramolecular melamine-cyanuric acid adduct [35]. Melamine (40.5 g, Aldrich, 98%) and cyanuric acid (41.5 g, Aldrich, 98%) were suspended in distilled water (300 mL) and heated at 90 • C for 12 h under continuous stirring. The suspension then was cooled, and a white Nanomaterials 2023, 13, 2176 3 of 16 solid was filtered off, which was then washed and dried in vacuum. The resulting material was placed in a muffle and kept at the temperature 550 • C for 1 h; the heating rate was 1 • C/min. The resulting light-yellow sample of g-C 3 N 4 was ground in a mortar.

Rh and Pd Deposition
[Rh 2 (H 2 O) 8 (µ-OH) 2 ](NO 3 ) 4 ·4H 2 O (prepared from K 3 RhCl 6 [37]) was dissolved in acetone + ethanol (3%) to obtain a solution with [Rh] of 0.568 mM (Rh solution). Also, (Et 4 N) 2 [Pd(NO 3 ) 4 ] (prepared from metallic palladium [38]) was dissolved in acetone to obtain a solution with [Pd] of 2.76 mM (Pd solution). An appropriate aliquot of Rh solution (11 mL for 0.5%, 2.2 mL for 0.1%, 1.1 mL for 0.05%, 0.22 mL for 0.01%), or Pd solution (4.8 mL for 0.5%, 0.96 mL for 0.1%, 0.48 mL for 0.05%, 0.096 mL for 0.01%), was added into a suspension of g-C 3 N 4 (250 mg) in 1.5 mL of acetone. The resulting suspensions were thoroughly mixed for one (Pd) or five (Rh) days at room temperature until the mother liquor become colorless. The powder was separated by filtration, washed with acetone and dried in an air flow. The dried powders were heated in a stream of hydrogen at 400 • C for 1 h yielding the X%M/g-C 3 N 4 (M = Rh or Pd) catalysts, where X = 0.5, 0.1, 0.05 or 0.01 and designates the percentage of corresponding metal (weight percent). For comparison, the deposition of 0.5% of Pd and Rh from solutions of [Pd(NH 3 ) 4 (NO 3 ) 2 ] and RhCl 3 was carried out using the same technique.

Photocatalyst Characterization
The photocatalysts were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), UV-Vis spectroscopy and high-resolution transmission electron microscopy (HRTEM) techniques. XRD investigations was performed with a D8 Advance powder diffractometer (Bruker, Germany) using CuKα radiation. XRD patterns were recorded in the 2θ range from 20 • to 80 • . The mean sizes of crystallites were estimated from the full width at half maximum of the corresponding peaks using the Scherrer formula as follows: where d-average size of coherent scattering crystallites (nm), K-Scherrer constant, λ-X-ray wavelength (nm), β-width of reflection at half height (2θ units), θ-diffraction angle. XPS studies were carried out on a SPECS Surface Nano Analysis GmbH photoelectron spectrometer (Berlin, Germany) with monochromatic AlKα radiation. Diffuse reflectance spectra were recorded on a UV-2501 PC spectrophotometer (Shimadzu, Japan) equipped with an ISR-240A diffuse reflectance cell. The structure of the photocatalysts was studied by HRTEM using a ThemisZ electron microscope (Thermo Fisher Scientific, Waltham, MA, USA) operated at an accelerating voltage of 200 kV.
Elemental analysis was carried out for several samples with the ICP-AES technique with the use of an iCAP-6500 high-resolution spectrometer (Thermo Scientific, Waltham, MA, USA, (ICP-AES)) with a cyclone-type spray chamber and a SeaSpray nebulizer. The actual content of metals was in good agreement with calculated values (Table S1).

Photocatalytic Activity
The activity of the photocatalyst was investigated in a batch reactor. The reaction suspension containing 50 mg of a photocatalyst and 100 mL of an aqueous or aqueous alkaline (C 0 (NaOH (Aldrich, 98%)) 10 vol.% triethanolamine (TEOA, Reachim, 98%) solution was purged with argon for 30 min to remove oxygen before the start of the photocatalytic reaction. Then, the suspension was irradiated using an LED radiation source (λ = 428 nm, 56 mW/cm 2 ). The area of the quartz window of the reactor was 22.5 cm 2 . The amount of hydrogen evolved was measured using a gas chromatograph (Khromos, Russia); the reaction duration was 90 min.
The apparent quantum efficiency (AQE) was calculated as follows: where W 0 -reaction rate (µmol min −1 ), N ph -photon flux constituting 283 µEinstein min −1 . The number of electrons (2) involved in the hydrogen formation reaction was taken into account in the apparent quantum efficiency calculation.

X-ray Diffraction
In order to characterize the crystalline phase of the Pd/g-C 3 N 4 and Rh/g-C 3 N 4 samples, XRD patterns of the synthesized photocatalysts were obtained ( Figure 1). Figure 1 shows that there are two main peaks in the XRD patterns, located at 13 and 27 • ; these peaks can be attributed to g-C 3 N 4 [16]. The peak located at 13 • corresponds to the reflection from the (210) plane and is due to the distance between the heptazine (tri-s-triazine) units in the 2D g-C 3 N 4 layer, and the diffraction peak (2θ~27 • ) belongs to the (002) plane and determines the distance between the 2D layers of g-C 3 N 4 [35,39]. It can be seen that the characteristic g-C 3 N 4 peak at 27 • becomes broader and weaker with the increase in Pd and Rh content ( Figure 1). For the sample 0.5% Pd/g-C 3 N 4 , a characteristic peak at 40.1 • appears, which belongs to the (111) diffraction plane of metallic Pd (Figure 1b). For the rest of the rhodium-and palladium-containing samples, no metal peaks were found, probably due to low mass fraction of Rh and Pd. tion was purged with argon for 30 min to remove oxygen before the start of the ph catalytic reaction. Then, the suspension was irradiated using an LED radiation sour = 428 nm, 56 mW/cm 2 ). The area of the quartz window of the reactor was 22.5 cm 2 . amount of hydrogen evolved was measured using a gas chromatograph (Khromos, sia); the reaction duration was 90 min.
The apparent quantum efficiency (AQE) was calculated as follows: where W0-reaction rate (µmol min −1 ), Nph-photon flux constituting 283 µEinstein m The number of electrons (2) involved in the hydrogen formation reaction was taken account in the apparent quantum efficiency calculation.

X-ray Diffraction
In order to characterize the crystalline phase of the Pd/g-C3N4 and Rh/g-C3N4 ples, XRD patterns of the synthesized photocatalysts were obtained ( Figure 1). Figu shows that there are two main peaks in the XRD patterns, located at 13 and 27°; t peaks can be attributed to g-C3N4 [16]. The peak located at 13° corresponds to the reflec from the (210) plane and is due to the distance between the heptazine (tri-s-triazine) u in the 2D g-C3N4 layer, and the diffraction peak (2θ~27°) belongs to the (002) plane determines the distance between the 2D layers of g-C3N4 [35,39]. It can be seen tha characteristic g-C3N4 peak at 27° becomes broader and weaker with the increase in Pd Rh content ( Figure 1). For the sample 0.5% Pd/g-C3N4, a characteristic peak at 40.1 pears, which belongs to the (111) diffraction plane of metallic Pd (Figure 1b). For the of the rhodium-and palladium-containing samples, no metal peaks were found, prob due to low mass fraction of Rh and Pd. The interlayer distance d002 for the all samples was ca. 3.22 Å, which is in good ag ment with the data obtained for g-C3N4 [39]. The average crystallite size in the plan The interlayer distance d 002 for the all samples was ca. 3.22 Å, which is in good agreement with the data obtained for g-C 3 N 4 [39]. The average crystallite size in the plane of the layer was 9.5-9.6 nm, and the average crystallite size in the direction perpendicular to the layer was 9.3-9.8 nm.

UV-Vis Spectroscopy
The optical properties of synthesized photocatalysts were investigated using UV-Vis spectroscopy ( Figure 2). One can see that the absorption edge for all samples is ca. 400 nm (Figure 2a,c). Also, the deposition of noble metals promotes the adsorption of visible light in the range 400-800 nm. Figure 2b,d show the data transformation for pristine g-C 3 N 4 , Pd (0.1 and 0.5 wt.%)/g-C 3 N 4 and Rh (0.1 and 0.5 wt.%)/g-C 3 N 4 photocatalysts in Tauc's coordinates for indirect semiconductors. It was shown that the deposition of metals has almost no effect on the band gap energy, which is in the range of 2.77-2.83 eV for all the samples. the layer was 9.3-9.8 nm.

UV-Vis Spectroscopy
The optical properties of synthesized photocatalysts were investigated using UV-Vis spectroscopy ( Figure 2). One can see that the absorption edge for all samples is ca. 400 nm (Figure 2a,c). Also, the deposition of noble metals promotes the adsorption of visible light in the range 400-800 nm. Figure 2b,d show the data transformation for pristine g-C3N4, Pd (0.1 and 0.5 wt.%)/g-C3N4 and Rh(0.1 and 0.5 wt.%)/g-C3N4 photocatalysts in Tauc's coordinates for indirect semiconductors. It was shown that the deposition of metals has almost no effect on the band gap energy, which is in the range of 2.77-2.83 eV for all the samples.

HR TEM Method
High-resolution TEM images show the morphology of 0.5% Pd/g-C3N4 ( Figure 3) and 0.5% Rh/g-C3N4 (Figure 4) photocatalysts and corresponding particle size distributions. Fourier transform of TEM images ( Figure S1) reveals the interplanar distance of 3.3 Å, which is in good agreement with the interplanar distance determined from the XRD patterns ( Figure 1) and with the previously published data [35,39,40]. One can see that both Pd and Rh particles have spherical shape. The average metal particles size was 3.1 ± 2.1 nm for Pd ( Figure 3d) and 2.5 ± 1.2 nm for Rh (Figure 4d), respectively. The particle size

HR TEM Method
High-resolution TEM images show the morphology of 0.5% Pd/g-C 3 N 4 ( Figure 3) and 0.5% Rh/g-C 3 N 4 (Figure 4) photocatalysts and corresponding particle size distributions. Fourier transform of TEM images ( Figure S1) reveals the interplanar distance of 3.3 Å, which is in good agreement with the interplanar distance determined from the XRD patterns ( Figure 1) and with the previously published data [35,39,40]. One can see that both Pd and Rh particles have spherical shape. The average metal particles size was 3.1 ± 2.1 nm for Pd ( Figure 3d) and 2.5 ± 1.2 nm for Rh (Figure 4d), respectively. The particle size distribution of both Pd and Rh includes particles ranging in size from 1 to 7 nm (Figures 3d and 4d). In addition, it should be noted that palladium forms large clusters 20-30 nm in size, while rhodium is more evenly distributed over the surface of g-C 3 N 4 . We can assume that rhodium complexes are adsorbed on the g-C 3 N 4 surface more uniformly, which is associated with the preferred structure of the complex Rh 2 (H 2 O) 8 3d and 4d). In addition, it should be noted that palladium forms large clusters 20-30 nm in size, while rhodium is more evenly distributed over the surface of g-C3N4. We can assume that rhodium complexes are adsorbed on the g-C3N4 surface more uniformly, which is associated with the preferred structure of the complex Rh2(H2O)8(µ-OH)2](NO3)4·4H2O compared to (Et4N)2[Pd(NO3)4.   HRTEM images were also used to confirm the presence of Pd and Rh in the synthesized photocatalysts ( Figure S2). The observed distances for 0.5% Rh/g-C3N4 were equal to 2. 19   HRTEM images were also used to confirm the presence of Pd and Rh in the synthesized photocatalysts ( Figure S2). The observed distances for 0.5% Rh/g-C 3 N 4 were equal to 2.19 and 1.91-1.92 Å, corresponding to Rh planes (111) and (200), respectively (PDF No. 5-685). A similar situation is observed for the 0.5% Pd/g-C 3 N 4 photocatalyst. The interplane distances were equal to 2.28 and 2.09 Å, respectively, corresponding to the Pd planes (111) and (200) (PDF No. 46-1043).

XPS Method
The study of the chemical composition of the samples was carried out with the XPS technique. The XPS spectra of the catalysts revealed peaks corresponding to Pd, Rh, N, C and O. Figure 5a,b shows the C1s and N1s spectra of pristine g-C 3 N 4 . The C1s spectrum is well described by two peaks with binding energies of 284.9 and 288.1 eV. The first peak is characteristic of carbon-containing impurities present on the surface of the objects under study (often used to calibrate the binding energy scale). The second peak is characteristic of C1s g-C 3 N 4 and corresponds to carbon forming bonds with nitrogen atoms in the g-C 3 N 4 structure [41,42]. In the case of the N1s spectrum, four peaks are observed with binding energies of 398.6, 400.0, 401.0 and 404.5 eV. According to the literature data, the first peak refers to nitrogen atoms forming a C-N=C bond, the second one to N-(C) 3 bonds with three carbon atoms, the third one to the N-H terminal groups and the fourth peak corresponds to an excited π bond [41].   Figure 5c shows the Rh3d spectra for the photocatalyst 0.5%Rh/g-C3N4. The Rh3d spectrum is described by one asymmetric Rh4f7/2-Rh4f7/2 doublet with a Rh3d5/2 binding energy of 306.5 eV and one symmetrical Rh4f7/2-Rh4f7/2 doublet with a Rh3d5/2 binding energy of 309.4 eV. In the literature, for metallic Rh, the binding energy of Rh4f7/2 is equal to 306.7-307.5 eV, and for Rh2O3 it lies in the range of 309.4-310.2 eV [28]. Thus, the doublet in the region of high binding energies refers to rhodium in the Rh 3+ state, and the narrow  Figure 5c shows the Rh3d spectra for the photocatalyst 0.5%Rh/g-C 3 N 4 . The Rh3d spectrum is described by one asymmetric Rh4f 7/2 -Rh4f 7/2 doublet with a Rh3d 5/2 binding energy of 306.5 eV and one symmetrical Rh4f 7/2 -Rh4f 7/2 doublet with a Rh3d 5/2 binding energy of 309.4 eV. In the literature, for metallic Rh, the binding energy of Rh4f 7/2 is equal to 306.7-307.5 eV, and for Rh 2 O 3 it lies in the range of 309.4-310.2 eV [28]. Thus, the doublet in the region of high binding energies refers to rhodium in the Rh 3+ state, and the narrow asymmetric doublet in the lower binding energies region can be attributed to rhodium in the metallic state Rh 0 . According to the analysis, the proportion of Rh in the metallic state is 75%, and rhodium in the Rh 3+ state is 25%, respectively. Figure 5d shows the Pd3d spectra of the 0.5% Pd/g-C 3 N 4 photocatalyst. The Pd3d spectrum is well described by the Pd3d 5/2 -Pd3d 3/2 doublet with Pd3d 5/2 binding energy of 335.0 eV. For palladium in the metallic state, the Pd3d 5/2 binding energy is 335.0-335.2 eV [32], and for PdO it is 336.6-337.7 eV [32,43]. Thus, in 0.5% Pd/g-C 3 N 4 catalyst, Pd exists completely in the metallic state.
The atomic percentages of the surface for the samples 0.5% Rh/g-C 3 N 4 and 0.5% Pd/g-C 3 N 4 are shown in Table S2. It can be seen that the surface content of rhodium is much higher than in the case of palladium at the same weight content. The presented data on the surface content of rhodium and palladium once again confirm that in the case of the first metal, the deposition occurs with the formation of smaller particles with a good coverage of the g-C 3 N 4 surface.
In general, from the characterization of photocatalysts, it can be concluded that 0.01-0.5% Pd/g-C 3 N 4 and 0.01-0.5% Rh/g-C 3 N 4 samples were obtained. In the case of the reduction of palladium from (Et 4 N) 2 [Pd(NO 3 ) 4 ] complex, it was possible to achieve a completely metallic state, whereas in the case of the use of [Rh 2 (H 2 O) 8 (µ-OH) 2 ](NO 3 ) 4 ·4H 2 O as a rhodium precursor, complete reduction of the metal was not achieved.

Photocatalyst Characterization
The activity of all synthesized samples 0.01-0.5% Pd/g-C 3 N 4 and 0.01-0.5% Rh/g-C 3 N 4 , as well as the activity of pristine g-C 3 N 4 and Pd-and Rh-containing samples before the reduction in hydrogen (with adsorbed complexes of palladium or rhodium after drying), was studied in the photocatalytic production of hydrogen in aqueous and aqueous alkaline solutions of TEOA. TEOA was chosen as a sacrificial agent as it helps to reduce photocorrosion of g-C 3 N 4 because the amino groups of TEOA effectively bind to the surface of g-C 3 N 4 [44,45]. Alkaline solution was used to facilitate proton abstraction during TEOA oxidation and to prevent charge recombination on the catalyst surface [46]. The photocatalytic activity was studied with the use of LED with a maximum emission at a wavelength of 428 nm as a light source (Figure 6a). Previously, it was shown that when using a diode with a maximum radiation in this region, the highest AQE was observed [35]. Note that over pristine g-C 3 N 4 , the rate was equal to zero both under neutral and alkali conditions. Figure 6b shows the kinetics of hydrogen formation for 0.1% Pd/g-C 3 N 4 and 0.1% Rh/g-C 3 N 4 samples without heat treatment and with H 2 reduction at 400 • C.
One can see that the activity of photocatalysts with adsorbed complexes of rhodium and palladium is an order of magnitude lower than after the reduction of the corresponding complexes with H 2 at 400 • C. As shown earlier for platinized photocatalysts, treatment with H 2 at 400 • C is a necessary step for the formation of a metal cocatalyst for hydrogen evolution on the surface of g-C 3 N 4 [35]. The next step in the study was to vary the mass fraction of metals from 0.01 to 0.5%. As was described before, [Rh 2 (H 2 O) 8 4 ] were used as precursors of rhodium and palladium, respectively; reduction in H 2 at 400 • C was used to obtain metallic particles for all samples. The data on activities of all the samples per 1 g of catalyst and per 1 g of noble metal are represented in Table 1. photocatalytic activity was studied with the use of LED with a maximum emission wavelength of 428 nm as a light source (Figure 6a). Previously, it was shown that w using a diode with a maximum radiation in this region, the highest AQE was obse [35]. Note that over pristine g-C3N4, the rate was equal to zero both under neutral alkali conditions. Figure 6b shows the kinetics of hydrogen formation for 0.1% Pd/gand 0.1% Rh/g-C3N4 samples without heat treatment and with H2 reduction at 400 °C  The photocatalytic activities vs. metal loading are shown in Figure 7. As can be seen, the catalytic activity increases with the increase in a metal content for both Pd and Rh (Figure 7a,c), and the highest catalytic activities were observed for 0.5% Rh/g-C 3 N 4 and 0.5%Pd/g-C 3 N 4 photocatalysts (Figure 7a,c). The activity of 0.5% Rh/g-C 3 N 4 photocatalysts was equal to ca. 3.9 mmol H 2 per gram per hour and was about 25% higher than the activity of the photocatalyst 0.5% Pd/g-C 3 N 4 . Recalculation of activity per 1 g of metal showed that the maximum value and the most efficient use of the metal was observed for 0.1% Rh/g-C 3 N 4 and was equal to 2.4 mol H 2 per gram of Rh per hour (Figure 7d). This parameter was already twice that of the photocatalyst 0.1% Pd/g-C 3 N 4 . The photocatalytic activities vs. metal loading are shown in Figure 7. As can be seen, the catalytic activity increases with the increase in a metal content for both Pd and Rh (Figure 7a,c), and the highest catalytic activities were observed for 0.5% Rh/g-C3N4 and 0.5%Pd/g-C3N4 photocatalysts (Figure 7a,c). The activity of 0.5% Rh/g-C3N4 photocatalysts was equal to ca. 3.9 mmol H2 per gram per hour and was about 25% higher than the activity of the photocatalyst 0.5% Pd/g-C3N4. Recalculation of activity per 1 g of metal showed that the maximum value and the most efficient use of the metal was observed for 0.1% Rh/g-C3N4 and was equal to 2.4 mol H2 per gram of Rh per hour (Figure 7d). This parameter was already twice that of the photocatalyst 0.1% Pd/g-C3N4. Thus, it can be concluded that in the case of supported rhodium for the Rh/g-C3N4 photocatalysts, the use of Rh nanoparticles in the formation of hydrogen is more efficient than in the case of supported palladium for the photocatalysts Pd/g-C3N4. This may be due to the fact that the palladium deposited on the surface of the carbon nitride has a larger particle size compared to rhodium (Figures 3 and 4). In addition, as can be seen from Figure 3b, palladium particles are collected into large aggregates, which can adversely affect the photocatalytic activity. The effect of metal nanoparticles-rhodium and palladium-as cocatalysts of hydrogen formation is likely similar. The deposition of metals leads to the separation of photogenerated charges due to the appearance of a Schottky barrier at the metal-semiconductor interface [8]. The main factor affecting the activity is most likely the formation of large agglomerates in the case of deposited rhodium. These Thus, it can be concluded that in the case of supported rhodium for the Rh/g-C 3 N 4 photocatalysts, the use of Rh nanoparticles in the formation of hydrogen is more efficient than in the case of supported palladium for the photocatalysts Pd/g-C 3 N 4 . This may be due to the fact that the palladium deposited on the surface of the carbon nitride has a larger particle size compared to rhodium (Figures 3 and 4). In addition, as can be seen from Figure 3b, palladium particles are collected into large aggregates, which can adversely affect the photocatalytic activity. The effect of metal nanoparticles-rhodium and palladium-as cocatalysts of hydrogen formation is likely similar. The deposition of metals leads to the separation of photogenerated charges due to the appearance of a Schottky barrier at the metal-semiconductor interface [8]. The main factor affecting the activity is most likely the formation of large agglomerates in the case of deposited rhodium. These large metal particles prevent the absorption of light by the semiconductor and can act as centers for the recombination of electron-hole pairs.
We compared numerical values obtained in this study with our previous results on platinized photocatalysts obtained with the (Bu 4 N) 2 [Pt(NO 3 ) 6 ] labile complex as a platinum precursor [35,45] as well as with previously published data on Pd/g-C 3 N 4 [27] and Rh/g-C 3 N 4 [26] photocatalysts. It has been shown that with similar methods of synthesis with the deposition of noble metals from labile precursor complexes, the highest activity in the series of Pt, Rh and Pd metals is observed for platinum. Thus, for the photocatalyst 0.5% Rh/g-C 3 N 4 under study, the activity per gram of catalyst was 4 mmol g −1 h −1 , and for the photocatalyst 0.5% Pt/g-C 3 N 4 [35] it was 11 mmol g −1 h −1 ; the difference in the highest specific activity per gram of metal was also about 3 times higher for platinum photocatalysts (Table 1). Platinum is known as the most effective co-catalyst for the formation of hydrogen because Pt forms the highest Schottky barrier at the metal-semiconductor interface, due to the highest work function relative to other metals [8]. It is interesting to note that the activity of palladium photocatalysts Pd/g-C 3 N 4 obtained using (Et 4 N) 2 [Pd(NO 3 ) 4 ] complex as a precursor of palladium is approximately on the same level as for photocatalysts for which ordinary palladium chloride acted as a precursor [27]. At the same time, Table 1 shows that the activity of rhodium photocatalysts Rh/g-C 3 N 4 obtained using [Rh 2 (H 2 O) 8 (µ-OH) 2 ](NO 3 ) 4 ·4H 2 O complex as a precursor is orders of magnitude higher than the activity of photocatalysts Rh/g-C 3 N 4 in which RhCl 3 or Rh(acac) 3 acted as a rhodium precursor [26]. In order to justify the choice of the precursor, the deposition of Pd and Rh (0.5 wt%) on the surface of g-C 3 N 4 with the use of [Pd(NH 3 ) 4 (NO 3 ) 2 ] and RhCl 3 as precursors, respectively, was carried out. The activity in the photocatalytic hydrogen evolution was lower by ca. 2 and 6 times for 0.5% Pd/g-C 3 N 4 and 0.5% Rh/g-C 3 N 4 photocatalysts compared to similar samples synthesized with the use of (Et 4 N) 2 Figure S3). Thus, the synthesis method proposed in this work for 0.01-0.5% Rh/g-C 3 N 4 photocatalysts can be considered quite promising, especially considering the acceptable activity at low mass fractions of the metal.
Next, the stability of the most active photocatalysts, 0.5 wt.% Pd/g-C 3 N 4 and 0.5 wt.% Rh/g-C 3 N 4 , was investigated in four runs in alkali (C 0 (NaOH) = 0.1 M) suspensions of TEOA, each of which lasted 1.5 h. After every 1.5 h of the reaction cycle, the suspension was purged with argon for 30 min. In the case of a 0.5% Pd/g-C3N4 photocatalyst, the activity dropped sharply after the first run and then remained unchanged for three runs (Figure 8a,b). The drop in the activity was by approximately three times (Figure 8b). As can be seen, the deactivation of 0.5% Rh/g-C3N4 occurred gradually, and no sharp drop in activity is observed after the first In the case of a 0.5% Pd/g-C 3 N 4 photocatalyst, the activity dropped sharply after the first run and then remained unchanged for three runs (Figure 8a,b). The drop in the activity was by approximately three times ( Figure 8b). As can be seen, the deactivation of 0.5% Rh/g-C 3 N 4 occurred gradually, and no sharp drop in activity is observed after the first cycle (Figure 8c,d). However, after the fourth cycle, the hydrogen evolution rate became 2 times lower compared to the first cycle (Figure 8d). Judging from the data of cyclic experiments, the decrease in activity in the case of photocatalysts with rhodium and palladium proceeded through different mechanisms. It can be assumed that the deactivation of the catalysts is most likely associated with the poisoning of active centers by TEOA oxidation products [35]. In order to reduce the influence of the resulting TEOA oxidation products, it was decided to study the stability of 0.5% Pd/g-C 3 N 4 and 0.5% Rh/g-C 3 N 4 under neutral conditions without addition of NaOH (Figure 9).  Figure 9c,d show that in the absence of NaOH, deactivation practically did not o in the case of 0.5% Rh/g-C3N4 and amounted to only 15% (Figure 9c,d). However, in eral, the activity was lower (Figure 9c,d) than in the experiments in alkaline media addition of NaOH (Figure 8c,d). Thus, for the first run, the rate was 2 times lower pared to the experiments in the alkaline suspension of TEOA. In the case of 0.5% P C3N4, the hydrogen evolution rate did not decrease compared to the experiments w NaOH was added into the reaction suspension; however, a twofold decrease in the after four runs was still observed (Figure 9a,b). We compared the surface content o ments before and after the photocatalytic tests for the samples 0.5% Pd/g-C3N4 and Rh/g-C3N4 using the XPS technique (Table S2). It was shown that for 0.5% Rh/g-C3N4 tocatalysts, after the hydrogen evolution both in alkaline media and without NaOH a tion, all rhodium became metallic with zero oxidation state; for both cases, the su content of the metal fell by 2 times but remained rather high. In the case of tests in a 0  Figure 9c,d show that in the absence of NaOH, deactivation practically did not occur in the case of 0.5% Rh/g-C 3 N 4 and amounted to only 15% (Figure 9c,d). However, in general, the activity was lower (Figure 9c,d) than in the experiments in alkaline media with addition of NaOH (Figure 8c,d). Thus, for the first run, the rate was 2 times lower compared to the experiments in the alkaline suspension of TEOA. In the case of 0.5% Pd/g-C 3 N 4 , the hydrogen evolution rate did not decrease compared to the experiments where NaOH was added into the reaction suspension; however, a twofold decrease in the rate after four runs was still observed (Figure 9a,b). We compared the surface content of elements before and after the photocatalytic tests for the samples 0.5% Pd/g-C 3 N 4 and 0.5% Rh/g-C 3 N 4 using the XPS technique (Table S2). It was shown that for 0.5% Rh/g-C 3 N 4 photocatalysts, after the hydrogen evolution both in alkaline media and without NaOH addition, all rhodium became metallic with zero oxidation state; for both cases, the surface content of the metal fell by 2 times but remained rather high. In the case of tests in a 0.1 M NaOH medium, significant surface carbonization was observed, which is probably the cause of deactivation. For the 0.5 % Pd/g-C 3 N 4 photocatalyst, we observed the decrease in surface Pd content only in alkaline media; however, the deactivation was observed both in the cases of alkaline and neutral media (Figures 8 and 9).
In general, it should be noted that the deactivation mechanisms differ for the Rh/g-C 3 N 4 and Pd/g-C 3 N 4 photocatalysts, which is associated with different charge states of metals and their particle size distribution and requires further study.

Conclusions
In this research, a series of photocatalysts 0.01-0.5% Pd/g-C 3 N 4 and 0.01-0.5% Rh/g-C 3 N 4 was synthesized and characterized by a set of physicochemical methods. A distinctive feature of the synthesis was the use as precursors of such labile complexes as [Rh 2 (H 2 O) 8  It was shown that the activity in the hydrogen evolution from aqueous solutions of TEOA under visible light for the 0.01-0.5% Rh/g-C 3 N 4 series is higher than in the case of the 0.01-0.5% Pd/g-C 3 N 4 photocatalysts. For the Rh/g-C 3 N 4 photocatalysts, the use of Rh nanoparticles in the formation of hydrogen is likely more efficient than in the case of supported palladium for the photocatalysts Pd/g-C 3 N 4 because palladium particles are collected into large aggregates, which can adversely affect the photocatalytic activity. The highest activity per gram of photocatalysts was possessed by the sample 0.5% Rh/g-C 3 N 4 and was equal to ca. 3.9 mmol H 2 g −1 h −1 ; the highest activity per gram of metal was possessed by 0.1% Rh/g-C 3 N 4 and was equal to 2.4 mol H 2 g Rh −1 h −1 . It is interesting to note that the activity of the Rh/g-C 3 N 4 photocatalysts obtained using [Rh 2 (H 2 O) 8 (µ-OH) 2 ](NO 3 ) 4 ·4H 2 O complex as a precursor is orders of magnitude higher than the activity of photocatalysts Rh/g-C 3 N 4 in which RhCl 3 or Rh(acac) 3 acted as a rhodium precursor [20]. Thus, the synthesis method proposed in this work for 0.01-0.5% Rh/g-C 3 N 4 photocatalysts can be considered quite promising, especially considering the acceptable activity at low mass fractions of the metal.
Supplementary Materials: The following supporting information can be downloaded at: https://www. mdpi.com/article/10.3390/nano13152176/s1, Figure S1. (a,b) HRTEM images of 0.5% Rh/g-C 3 N 4 and Fourier transform from the highlighted image. Figure S2. (a,b) HRTEM images of 0.5% Rh/g-C 3 N 4 and 0.5% Pd/g-C 3 N 4 . Figure S3. H 2 evolution rates for photocatalysts 0.5% Pd/g-C 3 N 4 and 0.5% Rh/g-C 3 N 4 synthesized from different metal precursors. Table S1. Actual metal content in the samples determined with ICP AES. Table S2. Surface element atomic concentration calculated based on XPS data of fresh 0.5% Pd/g-C 3 N 4 and 0.5% Rh/g-C 3 N 4 photocatalysts and these photocatalysts after cyclic runs in 0.1 M NaOH and water (Figures 8 and 9).

Institutional Review Board Statement: Not applicable.
Informed Consent Statement: Not applicable.

Data Availability Statement:
The data presented in this study are available on request from the corresponding author.