Nonlinear Optical Modulation Characteristics of MXene Cr2C for 2 μm Pulsed Lasers

MXene materials have shown numerous useful mechanical and electronic properties, and have been found to possess nice potential in the field of optical modulation. Here, we fabricated a MXene Cr2C saturable absorber by the liquid-phase exfoliation method, and systemically analyzed the surface morphology and nonlinear properties of the Cr2C sample. Applying the Cr2C saturable absorber as a Q-switch in a thulium-doped yttrium aluminum perovskite (Tm: YAP) laser, the shortest single pulse was obtained with a width of 602 ns under an absorbed pump power of 3.3 W at a repetition rate of 55 kHz with a T = 1% output coupler. The maximum output power was obtained with a T = 5% output coupler at a repetition rate of 58 kHz. The obtained maximum pulse energy and peak power were 3.96 μJ and 4.36 W, separately, which reveal that the MXene Cr2C can be applied as a promising modulation material in the near-infrared pulsed lasers.


Introduction
In recent years, nanomaterials have been widely applied in medicine, energy, microelectronics and other fields due to their magnetic, electrical, optical and chemical properties [1]. For example, Abouzar et al. investigated nanomaterials-based capacitors and applied them in the field of deoxyribonucleic acid (DNA) detection [2]; Schöning et al. reported the latest technologies and development trend advancements of biosensitive field effect devices (FED) with applied nanomaterials [3]. As a novel two-dimensional nanomaterial, MXene has attracted the attention of many researchers since it was firstly reported by Naguib et al. in 2011 [4]. MXenes have been applied in the field of energy storage and conversion [5,6], field-effect transistor (FET) [7,8], catalysis [9][10][11] and sensors [12][13][14] because of their excellent electronic and optical properties. Moreover, in the field of optical modulation, the 2D nanomaterials MXenes have been demonstrated as promising saturable absorbers (SAs) candidates due to their remarkable nonlinear modulation properties [15]. In the last few years, Wang et al. conducted studies on the nonlinear optical properties of MXene Mo 2 C, and successfully employed it as a SA for passively Q-switched lasers at 1 and 1.3 µm due to its high modulation depth [16,17]. Recently, a novel MXene material called Cr 2 C has attracted much attention in the fields of hydrogen storage [18] and electrical conduction [19]. Due to its similar structure but more stable physical and chemical properties compared to Mo 2 C, Cr 2 C is reasonably expected to possess similar or even better optical modulation and other optical responses. However, there is still no relevant report for the optical modulations of Cr 2 C MXene in the generation of pulsed lasers, leaving an unexplored territory of this material.
Based on the physical and chemical properties of Cr 2 C, we expect to apply Cr 2 C materials in the modulation field of 2 µm pulsed lasers. The eye safety lasers operating at a 2 µm laser have significant applications in atmospheric remote sensing [20], coherent LIDAR [21,22], industrial material processing [23] and medical scalpels in surgery [24]. Compared with continuous wave (CW) lasers, pulsed lasers with a high peak power and large pulse energy are more addictive in laser surgery and industrial processing. To achieve the pulsed laser output, one of the most efficient solutions is Q-switching. By employing various novel saturable absorption materials, such as graphene, black phosphorus, transition metal oxides and topological insulators, passive Q-switched lasers (PQS) can be achieved economically and compactly.
The saturable absorption of materials refers to the nonlinear optical phenomenon caused by the Pauli blocking effect which occurs under high intensity light [25]. When a beam of light with photon energies is larger than the band gap of the nonlinear optical material, the electrons in the valence band of the material will transit to the conduction band under the excitation of the incident photons. As shown in Figure 1a, at low incident light intensity, most of the photons are absorbed by the material, which is called the linear absorption state, exhibiting low transmittance. As the incident light intensity increases, more electrons in the valence band are excited to the conduction band until the electrons in the valence band are depleted and the conduction band is occupied by the carrier, as shown in Figure 1c. Thus, most incident photons cannot be absorbed and the material exhibits high transmittance in the saturable absorption state [26]. similar or even better optical modulation and other optical responses. However, there is still no relevant report for the optical modulations of Cr2C MXene in the generation of pulsed lasers, leaving an unexplored territory of this material.
Based on the physical and chemical properties of Cr2C, we expect to apply Cr2C materials in the modulation field of 2 µm pulsed lasers. The eye safety lasers operating at a 2 µm laser have significant applications in atmospheric remote sensing [20], coherent LI-DAR [21,22], industrial material processing [23] and medical scalpels in surgery [24]. Compared with continuous wave (CW) lasers, pulsed lasers with a high peak power and large pulse energy are more addictive in laser surgery and industrial processing. To achieve the pulsed laser output, one of the most efficient solutions is Q-switching. By employing various novel saturable absorption materials, such as graphene, black phosphorus, transition metal oxides and topological insulators, passive Q-switched lasers (PQS) can be achieved economically and compactly.
The saturable absorption of materials refers to the nonlinear optical phenomenon caused by the Pauli blocking effect which occurs under high intensity light [25]. When a beam of light with photon energies is larger than the band gap of the nonlinear optical material, the electrons in the valence band of the material will transit to the conduction band under the excitation of the incident photons. As shown in Figure 1a, at low incident light intensity, most of the photons are absorbed by the material, which is called the linear absorption state, exhibiting low transmittance. As the incident light intensity increases, more electrons in the valence band are excited to the conduction band until the electrons in the valence band are depleted and the conduction band is occupied by the carrier, as shown in Figure 1c. Thus, most incident photons cannot be absorbed and the material exhibits high transmittance in the saturable absorption state [26]. In this paper, we systematically investigated the optical response of MXene Cr2C materials and focused on the nonlinear optical modulation properties of MXene Cr2C as a saturable absorber for a 2 µm pulsed laser. Firstly, Cr2C MXene SA was successfully prepared by liquid-phase exfoliation (LPE), and its morphology was characterized in detail by X-ray diffraction (XRD) and atomic force microscopy (AFM) in the following experiment. Then, the transmittance spectral and nonlinear optical responses of Cr2C SA were measured by the UV-Vis-NIR spectrophotometer and open-aperture Z-scan method, respectively. Finally, we achieved a stable passively Q-switched Tm: YAP laser operation at 1985 nm employing the Cr2C SA. Under an absorbed pump power of 3.3 W, the maximum In this paper, we systematically investigated the optical response of MXene Cr 2 C materials and focused on the nonlinear optical modulation properties of MXene Cr 2 C as a saturable absorber for a 2 µm pulsed laser. Firstly, Cr 2 C MXene SA was successfully prepared by liquid-phase exfoliation (LPE), and its morphology was characterized in detail by X-ray diffraction (XRD) and atomic force microscopy (AFM) in the following experiment. Then, the transmittance spectral and nonlinear optical responses of Cr 2 C SA were measured by the UV-Vis-NIR spectrophotometer and open-aperture Z-scan method, respectively. Finally, we achieved a stable passively Q-switched Tm: YAP laser operation at 1985 nm employing the Cr 2 C SA. Under an absorbed pump power of 3.3 W, the maximum output power of 221 mW was obtained with a T = 5% output coupler (OC), corresponding to a slope efficiency of 17.6%. The shortest pulse duration was measured to be 602 ns with a repetition rate of 55 kHz with a T = 1% OC. The experimental results demonstrate the potential applications of MXene Cr 2 C in the field of nonlinear optical modulation.

Preparation and Characterization
The Cr 2 C SA was fabricated by the conventional ultrasound-assisted LPE technique. During the preparation of SA, 5 mg of Cr 2 C powder was firstly dissolved in 5 mL of anhydrous isopropyl alcohol solution. After ultrasonic shaking for 2 h, the Cr 2 C dispersion was further centrifuged at 3000 rpm for 15 min by the differential centrifugation method. Then, the supernatant liquid was collected and dropped onto a quartz substrate with a size of 2 × 2 × 0.5 mm 3 . Subsequently, the quartz substrate was placed on a rotating coater and coated for 1 min at a speed of 500 rpm. Finally, the Cr 2 C SA was prepared after an air-drying treatment at a normal atmospheric temperature.
To confirm the constituent of the Cr 2 C MXene sample, X-ray diffraction (Bruker AXS D8 Advance, Karlsruhe, Germany) measurement was performed, and the results were shown in Figure 2a. There are mainly four kinds of materials in the sample: the Cr 2 C (black star), the AlCr 2 C (black triangle), the Cr 3 C 2 (black square) and the Cr 23 C 6 (black circle). As the Cr 2 C MXene materials were fabricated by selectively etching Al atoms from the MAX phase of AlCr 2 C, the AlCr 2 C detected by XRD should be the residue from the etching process [27]. For the Cr 3 C 2 and the Cr 23 C 6 , they would both be the by-products of the deterioration of the Cr 2 C MXenes [28]. Compared with the standard Cr 2 C structure data (ICDD database no. PDF 14-0519) [29], it can be found that the content of Cr 2 C in the sample is predominant, which indicates that the properties presented by the sample in the experiment should be mainly derived from the Cr 2 C material. Furthermore, the irregularity of the baseline may be caused by the unsatisfactory crystallinity of the sample and some amorphous materials. Nanomaterials 2023, 13, x FOR PEER REVIEW 3 of 10 output power of 221 mW was obtained with a T = 5% output coupler (OC), corresponding to a slope efficiency of 17.6%. The shortest pulse duration was measured to be 602 ns with a repetition rate of 55 kHz with a T = 1% OC. The experimental results demonstrate the potential applications of MXene Cr2C in the field of nonlinear optical modulation.

Preparation and Characterization
The Cr2C SA was fabricated by the conventional ultrasound-assisted LPE technique. During the preparation of SA, 5 mg of Cr2C powder was firstly dissolved in 5 mL of anhydrous isopropyl alcohol solution. After ultrasonic shaking for 2 h, the Cr2C dispersion was further centrifuged at 3000 rpm for 15 min by the differential centrifugation method. Then, the supernatant liquid was collected and dropped onto a quartz substrate with a size of 2 × 2 × 0.5 mm³. Subsequently, the quartz substrate was placed on a rotating coater and coated for 1 min at a speed of 500 rpm. Finally, the Cr2C SA was prepared after an airdrying treatment at a normal atmospheric temperature.
To confirm the constituent of the Cr2C MXene sample, X-ray diffraction (Bruker AXS D8 Advance, Karlsruhe, Germany) measurement was performed, and the results were shown in Figure 2a. There are mainly four kinds of materials in the sample: the Cr2C (black star), the AlCr2C (black triangle), the Cr3C2 (black square) and the Cr23C6 (black circle). As the Cr2C MXene materials were fabricated by selectively etching Al atoms from the MAX phase of AlCr2C, the AlCr2C detected by XRD should be the residue from the etching process [27]. For the Cr3C2 and the Cr23C6, they would both be the by-products of the deterioration of the Cr2C MXenes [28]. Compared with the standard Cr2C structure data (ICDD database no. PDF 14-0519) [29], it can be found that the content of Cr2C in the sample is predominant, which indicates that the properties presented by the sample in the experiment should be mainly derived from the Cr2C material. Furthermore, the irregularity of the baseline may be caused by the unsatisfactory crystallinity of the sample and some amorphous materials. To visualize the morphological features of Cr 2 C SA, the atomic force microscopy (AFM; HORIBA SmartSPM, Kyoto, Japan) measurement was employed. The AFM image of the Cr 2 C MXene sample and the typical height profile diagrams shown in Figure 2b,c clearly indicated that the Cr 2 C MXene was exfoliated successfully into a 2D layered sheet with a nanoscale size. As shown in Figure 2b, Cr 2 C was extensively and quasi-uniformly attached to the substrate after preparation by liquid-phase stripping and the size of the material in the 2D plane was on the order of micrometers. There are several sparse bright spots at the edge of Figure 2b, which refer to residual bulk particles due to incomplete stripping. These bulk particles do not substantially interfere with the subsequent experimental results because they are sparsely distributed. The height profiles of the Cr 2 C nanosheets measured along the A, B, C and D lines are shown in Figure 2c, reflecting the thickness distribution of the Cr 2 C nanosheets between 10 nm and 25 nm. These results indicate that we successfully prepared Cr 2 C materials into Cr 2 C nanosheets by the liquid-phase exfoliation (LPE) method.
The transmittance characteristics of Cr 2 C SA were further confirmed by measuring the optical transmittance spectrum of Cr 2 C SA between 500 and 2500 nm using a UV-Vis-NIR spectrophotometer (Hitachi UH4150, Tokyo, Japan). As shown in Figure 3b, the transmittance of the Cr 2 C SA was higher than 80% in the whole spectrum and above 92% near the 2 µm region, which indicates that Cr 2 C SA has a certain absorption capacity and broadband transmittance characteristics. Moreover, since one lamp can hardly cover the entire wavelength range, we switched the lamp during the course of the experiment, which resulted in two obvious fluctuations in the transmission curve at wavelengths of 660 nm and 1650 nm. To visualize the morphological features of Cr2C SA, the atomic force microscopy (AFM; HORIBA SmartSPM, Kyoto, Japan) measurement was employed. The AFM image of the Cr2C MXene sample and the typical height profile diagrams shown in Figure 2b,c clearly indicated that the Cr2C MXene was exfoliated successfully into a 2D layered sheet with a nanoscale size. As shown in Figure 2b, Cr2C was extensively and quasi-uniformly attached to the substrate after preparation by liquid-phase stripping and the size of the material in the 2D plane was on the order of micrometers. There are several sparse bright spots at the edge of Figure 2b, which refer to residual bulk particles due to incomplete stripping. These bulk particles do not substantially interfere with the subsequent experimental results because they are sparsely distributed. The height profiles of the Cr2C nanosheets measured along the A, B, C and D lines are shown in Figure 2c, reflecting the thickness distribution of the Cr2C nanosheets between 10 nm and 25 nm. These results indicate that we successfully prepared Cr2C materials into Cr2C nanosheets by the liquidphase exfoliation (LPE) method.
The transmittance characteristics of Cr2C SA were further confirmed by measuring the optical transmittance spectrum of Cr2C SA between 500 and 2500 nm using a UV-Vis-NIR spectrophotometer (Hitachi UH4150, Tokyo, Japan). As shown in Figure 3b, the transmittance of the Cr2C SA was higher than 80% in the whole spectrum and above 92% near the 2 µm region, which indicates that Cr2C SA has a certain absorption capacity and broadband transmittance characteristics. Moreover, since one lamp can hardly cover the entire wavelength range, we switched the lamp during the course of the experiment, which resulted in two obvious fluctuations in the transmission curve at wavelengths of 660 nm and 1650 nm. To probe the nonlinear optical properties of Cr2C SA at 2 µm, we performed Z-scan measurements with a homemade OA Z-scanner, employing a 2 µm laser with 800 Hz repetition rate and 100 ns pulse width. As shown in Figure 3a, to improve the operability of the experiment and the reliability of the results, the Cr2C MXene sample was mounted on the guide rail between the focal lens and the power meter, so that the sample can be moved along the guide rail. Based on this design, we can move the SA on the guide rail to change the incident saturation fluence on the sample during the experiment. As illustrated in Figure 3c, the normalized transmittance curve gradually reached the maximum with the Cr2C To probe the nonlinear optical properties of Cr 2 C SA at 2 µm, we performed Z-scan measurements with a homemade OA Z-scanner, employing a 2 µm laser with 800 Hz repetition rate and 100 ns pulse width. As shown in Figure 3a, to improve the operability of the experiment and the reliability of the results, the Cr 2 C MXene sample was mounted on the guide rail between the focal lens and the power meter, so that the sample can be moved along the guide rail. Based on this design, we can move the SA on the guide rail to change the incident saturation fluence on the sample during the experiment. As illustrated in Figure 3c, the normalized transmittance curve gradually reached the maximum with the Cr 2 C SA approaching the focus position symmetrically, indicating the expected nonlinear absorption response of the as-prepared Cr 2 C at 2 µm. In order to quantify the nonlinear absorption capability of the as-prepared Cr 2 C, we numerically fitted the Z-scan experimental data by the formula [30]: where L e f f = 1 − e Lα 0 /α 0 is the effective thickness of the nonlinear optical material, α 0 is the linear absorption coefficient, L is the actual thickness of the sample, I 0 represents the maximum optical power density at the focus and β eff represents the effective nonlinear absorption coefficient of the material. By fitting the measured Z-scan results, the β eff was calculated to be −(2.75 ± 0.08) × 10 −2 cm/GW. To further confirm the nonlinear saturable absorption properties of the as-prepared Cr 2 C, we performed the I-scan measurement by adding an adjustable light attenuator to the Z-scan setup. The transmittance of the sample versus the beam intensity was measured by varying the incident beam intensity with an adjustable attenuator while the position of the sample was fixed. The nonlinear transmission curve was obtained by fitting the I-scan experimental data with the following formula [30]: where ∆T is the modulation depth, representing the maximum amount of variation in the material transmission rate, which affects the width of the output pulse. I represents the input intensity. I S = hv/2σ A τ A is the saturation intensity, in which hv is the photon energy, σ A is the absorption cross section of the material and τ A represents the saturation recovery time required for the material from the bleached state to the linear absorption state, which is the decisive factor of the narrowest pulse width. The non-saturable losses T ns refers to the scattering loss or Fresnel loss due to the roughness of the material surface. It should be pointed out that excessive non-saturable losses will suppress the operation efficiency of the laser. As shown in Figure 3d, the nonlinear transmittance increased with the power density and gradually reached saturation. The fitted curve gave the modulation depth ∆T, the saturation intensity I S and the non-saturable losses T ns of the Cr 2 C SA as 7.5%, 6.7 MW/cm 2 and 4.35%, respectively. It follows that Cr 2 C SA has excellent nonlinear optical properties, which indicates its potential as a candidate for laser pulse modulation.

Results and Discussion
To further confirm the saturation absorption properties of the prepared Cr 2 C SA, a Q-switched Tm: YAP laser was designed employing the Cr 2 C SA, and the diagram of the laser device was shown in Figure 4a. In the device, an 18 mm plane-plane straight cavity was built consisting of an input coupler (M1) and an output coupler (M2). The M1 was coated with anti-reflectivity (AR) and high-reflection (HR) at 790 nm and 1940 nm, separately. We successively utilized three flat mirrors with a different transmittance at 2 µm as the output couplers during the measurements, and the transmittance of the OC was 1%, 3% and 5%, respectively. The gain medium was a (3 × 3 × 10) mm 3 size a-cut Tm: YAP crystal (doping concentration: 3 at%) with large thermal conductivity. The thermal load in the laser operation can be eliminated by mounting the gain medium wrapped with indium foil onto a water-cooled copper radiator cooled at 15 • C. The 794 nm pump light was generated by a laser diode and guided by an optical fiber with a core diameter of 400 µm and a numerical aperture of 0.22. To focus the pump beam on the gain medium properly, we employed an optical refocus module (1:1) consisting of two focus lenses. A filter was installed at the back of the M2 to eliminate the residual pump energy. A power meter (Thorlabs PM100D, Newtown, NJ, USA) was utilized to measure the output power, while a digital fluorescence oscilloscope (Tektronix DPO42102B-L, Beaverton, OR, USA) was connected to an InGaAs PIN photodetector (EOT ET-5000, MI, USA) to keep a record of the pulse temporal behavior.
3, x FOR PEER REVIEW 6 of 10 while a digital fluorescence oscilloscope (Tektronix DPO42102B-L, Beaverton, OR, USA) was connected to an InGaAs PIN photodetector (EOT ET-5000, MI, USA) to keep a record of the pulse temporal behavior. We firstly performed the continuous wave (CW) laser operation without the Cr2C SA. Figure 4b shows that the CW Tm: YAP laser average output powers increased versus the absorbed pump powers with three different OCs of T = 1%, 3% and 5%, respectively. As the absorption pump power continued to increase, the average output power of the CW Tm: YAP laser increased roughly linearly. Under the absorbed pump power of 3.3 W, the maximum output power of 516 mW was obtained with a T = 5% OC, corresponding to a slope efficiency of 31.1%. In addition, a stable passive Q-switched (PQS) laser operation was achieved by inserting Cr2C SA into the cavity near the OC. The variation trend of the output power of a Q-switched Tm: YAP laser was demonstrated in Figure 4c. The obtained maximum average output power was 221 mW with the T = 5% OC under an absorbed pump power of 3.3 W, with a slope efficiency of 17.6%. Comparing the operating characteristics of CW and Q-switched lasers, the pumping threshold of the Q-switched regime was higher than that of the CW regime, while the average output power was lower, which was due to the increased loss after the insertion of Cr2C SA. The instability of the Qswitched laser operation increased when the absorbed pump power exceeded 3.3 W, probably due to the limitation of the thermal effects as well as the possible oversaturation of the Cr2C SA.
As shown in Figure 4d, the emission spectra of the Tm: YAP laser operating in the CW and Q-switched regimes with the OC of T = 1% were measured by a laser spectrometer (APE Wave Scan, Berlin, Germany). The center wavelength was 1995.4 nm when the laser operating in the CW regime. After inserting Cr2C SA into the cavity, the output wavelength blue-shifted to 1985 nm, which was mainly caused by the insertion loss of the saturable absorber.
To further verify the nonlinear optical modulation performance of the Cr2C SA, we measured the pulse duration and repetition frequency of the PQS laser, which are shown in Figure 5a,b. The pulse duration continuously decreased with the increasing absorbed We firstly performed the continuous wave (CW) laser operation without the Cr 2 C SA. Figure 4b shows that the CW Tm: YAP laser average output powers increased versus the absorbed pump powers with three different OCs of T = 1%, 3% and 5%, respectively. As the absorption pump power continued to increase, the average output power of the CW Tm: YAP laser increased roughly linearly. Under the absorbed pump power of 3.3 W, the maximum output power of 516 mW was obtained with a T = 5% OC, corresponding to a slope efficiency of 31.1%. In addition, a stable passive Q-switched (PQS) laser operation was achieved by inserting Cr 2 C SA into the cavity near the OC. The variation trend of the output power of a Q-switched Tm: YAP laser was demonstrated in Figure 4c. The obtained maximum average output power was 221 mW with the T = 5% OC under an absorbed pump power of 3.3 W, with a slope efficiency of 17.6%. Comparing the operating characteristics of CW and Q-switched lasers, the pumping threshold of the Q-switched regime was higher than that of the CW regime, while the average output power was lower, which was due to the increased loss after the insertion of Cr 2 C SA. The instability of the Q-switched laser operation increased when the absorbed pump power exceeded 3.3 W, probably due to the limitation of the thermal effects as well as the possible oversaturation of the Cr 2 C SA.
As shown in Figure 4d, the emission spectra of the Tm: YAP laser operating in the CW and Q-switched regimes with the OC of T = 1% were measured by a laser spectrometer (APE Wave Scan, Berlin, Germany). The center wavelength was 1995.4 nm when the laser operating in the CW regime. After inserting Cr 2 C SA into the cavity, the output wavelength blue-shifted to 1985 nm, which was mainly caused by the insertion loss of the saturable absorber.
To further verify the nonlinear optical modulation performance of the Cr 2 C SA, we measured the pulse duration and repetition frequency of the PQS laser, which are shown in Figure 5a,b. The pulse duration continuously decreased with the increasing absorbed pump power. Under the pump power of 3.3 W, the shortest pulse duration of 601 ns, 699 ns and 907 ns were obtained with OCs of T = 1%, 3% and 5%, respectively. In contrast to the variation trend of the pulse durations, the repetition rates increased with the absorbed Nanomaterials 2023, 13,1965 7 of 10 pump power. As shown in Figure 5b, the repetition rates of the lasers under different OCs increased from 22 kHz, 32 kHz and 26 kHz to 55 kHz, 72 kHz and 58 kHz, respectively. Figure 5c shows the peak powers increased with the absorbed pump power. Among the three lasers, the obtained maximum peak powers were 4.16 W, 4.27 W and 4.36 W with a transmittance of T = 1%, 3% and 5%, respectively. The dependences of single pulse energy on the absorbed pump power were shown in Figure 5d. With the increase of pump power, the single-pulse energy increased almost linearly at the beginning and gradually reached saturation, which could be attributed to the thermal effect of the laser crystal and the oversaturation of the SA. The maximum single-pulse energies for the OCs of T = 1%, 3% and 5% were 2.51 µJ, 2.99 µJ and 3.96 µJ, respectively. A typical pulse train at T = 1% and a temporal pulse profile with a pulse duration of 602 ns were recorded and shown in Figure 5e. During a two-hour detection period, the pulsed laser maintained a stable output and the maximum output power instability was less than 7%, indicating the long-term stability of Cr 2 C SA. All of these experimental results demonstrated the stable Q-switched performance and the potential optical modulation applications for the Cr 2 C SA. Nanomaterials 2023, 13, x FOR PEER REVIEW 7 of 10 Figure 5c shows the peak powers increased with the absorbed pump power. Among the three lasers, the obtained maximum peak powers were 4.16 W, 4.27 W and 4.36 W with a transmittance of T = 1%, 3% and 5%, respectively. The dependences of single pulse energy on the absorbed pump power were shown in Figure 5d. With the increase of pump power, the single-pulse energy increased almost linearly at the beginning and gradually reached saturation, which could be attributed to the thermal effect of the laser crystal and the oversaturation of the SA. The maximum single-pulse energies for the OCs of T = 1%, 3% and 5% were 2.51 µJ, 2.99 µJ and 3.96 µJ, respectively. A typical pulse train at T = 1% and a temporal pulse profile with a pulse duration of 602 ns were recorded and shown in Figure  5e. During a two-hour detection period, the pulsed laser maintained a stable output and the maximum output power instability was less than 7%, indicating the long-term stability of Cr2C SA. All of these experimental results demonstrated the stable Q-switched performance and the potential optical modulation applications for the Cr2C SA.  Table 1 shows the PQS solid-state lasers with other 2D nanomaterials as SAs at 2 µm, including Mo2C [16], BP [31], graphene [32], MoS2 [33], WS2 [33], MoTe2 [34] and Mg-MOF-74 [35]. Compared to the other 2D nanomaterials, Cr2C has unique balanced advantages at optical modulation.    [34] and Mg-MOF-74 [35]. Compared to the other 2D nanomaterials, Cr 2 C has unique balanced advantages at optical modulation.

Conclusions
In this work, we present the first demonstration of a passive Cr 2 C Q-switched stable 2 µm laser. A Cr 2 C saturable absorber was successfully fabricated by a liquid-phase exfoliation technique. The morphology and the nonlinear optical properties of Cr 2 C SA were comprehensively investigated. Through Z-scan experiments and I-scan experiments, the effective nonlinear absorption coefficient, the modulation depth, the saturation intensity and the non-saturable losses of Cr 2 C SA were obtained with −(2.75 ± 0.08) × 10 −2 cm/GW, 7.5%, 6.7 MW/cm 2 and 4.35%, respectively, indicating the potential of Cr 2 C SA for pulsed laser modulation. Under a pump power of 3.3 W, we obtained the maximum average output power of 221 mW at a repetition rate of 58 kHz with an OC of T = 5%, corresponding to the maximum single-pulse energy of 3.96 µJ and peak power of 4.36 W. The shortest pulse duration was 602 ns at a repetition rate of 55 kHz with a T = 1% OC. By applying a T = 3% OC, the repetition rates of the laser pulses can reach 72 kHz. Compared to the other 2D nanomaterials, Cr 2 C has unique balanced advantages at optical modulation. These results validate that MXene Cr 2 C materials have effective nonlinear absorption properties and modulation capabilities. This work is of significance in the laser pulse generation for future research, especially in the modification of novel low-dimensional nanomaterials of nonlinear saturable absorption properties, and is also profound for expanding the application field of Cr 2 C materials.  Data Availability Statement: Data will be made available on request.