Bimetallic Nanocrystals: Structure, Controllable Synthesis and Applications in Catalysis, Energy and Sensing

In recent years, bimetallic nanocrystals have attracted great interest from many researchers. Bimetallic nanocrystals are expected to exhibit improved physical and chemical properties due to the synergistic effect between the two metals, not just a combination of two monometallic properties. More importantly, the properties of bimetallic nanocrystals are significantly affected by their morphology, structure, and atomic arrangement. Reasonable regulation of these parameters of nanocrystals can effectively control their properties and enhance their practicality in a given application. This review summarizes some recent research progress in the controlled synthesis of shape, composition and structure, as well as some important applications of bimetallic nanocrystals. We first give a brief introduction to the development of bimetals, followed by the architectural diversity of bimetallic nanocrystals. The most commonly used and typical synthesis methods are also summarized, and the possible morphologies under different conditions are also discussed. Finally, we discuss the composition-dependent and shape-dependent properties of bimetals in terms of highlighting applications such as catalysis, energy conversion, gas sensing and bio-detection applications.


Introduction
Crystals with at least one dimension at the nanometer level (1~100 nm) are known as nanocrystals. At the nanoscale, materials exhibit fascinating physical and chemical properties due to quantum size effect [1,2]. For instance, bulk gold has no activity for CO oxidation at low temperatures, while nanoscale gold has high catalytic activity [3]. Therefore, the controlled synthesis and application of metal nanocrystals have always been a research hotspot in the field of nanochemistry. The composition and structure of noble metals are relatively simple, and they have been used in many applications such as catalysis [4][5][6], electronics [7], and information storage [8] and so on. However, single metal nanocrystals have some shortcomings that are difficult to overcome in the application process. For example, although Pt catalyst has high catalytic activity for CO oxidation, it is easily poisoned. In addition, the amount of noble metals on earth are very low, and the reserves are extremely limited. Therefore, bimetallic nanocrystals have drawn the attention of a large number of researchers because bimetal exhibits not only a combination of two monometallic properties, but also some new properties due to synergistic effects [9][10][11][12][13].
As shown in Figure 1, metals have their own inherent properties, such as magnetic metal (Fe, Co, Ni), plasmonic metal (Cu, Au, Ag), and catalytic metal (Pd, Pt, Rh, Ru, Ir). However, some noble metals are relatively rare on earth, and the price is quite high. Nanomaterials 2021, 11, 1926 2 of 37 In the process of preparing catalysts, the commonly used precious metal precursors are chlorides or nitrates. Taking chlorides as an example, the order of the price of precious metals is RhCl 3 > IrCl 3 > AuCl > PdCl 2 > PtCl 2 > RuCl 3 . The price of the cheapest RuCl 3 is about 150-fold that of NiCl 2 ·6H 2 O, and 70-folds than that of CuCl 2 ·2H 2 O. In addition, the properties of a single metal are often not perfect. Nanocatalysts composed of two different metals have excellent catalytic performance and relatively low cost, and are becoming a frontier basic subject of interdisciplinary research in inorganic chemistry, nanoscience, and catalytic chemistry. Since bimetals have a two-component common energy band, by changing the composition of the alloy, the electronic structure and geometric configuration of the particle surface can be continuously changed by adjusting the distance between the d-band position of the metal and the Fermi energy level, It can change the adsorption capacity of nanoparticles for reactants and products, and then affect the activity, selectivity and stability of the catalyst [14]. Many works in the literature have proved that PtNi catalyst exhibited much higher catalytic performance than pure Pt for the oxygen reduction reaction (ORR) in fuel cells. For example, Zhao and co-workers reported that intermetallic PtNi catalyst exhibited remarkably enhanced ORR activity in comparison to the disordered PtNi and commercial Pt/C, and the durability also was improved by N doping [15]. The physicochemical properties of bimetallic nanocrystals are highly related to the spatial arrangement, atomic ordering and proportion of the different types of atoms. Therefore, the physicochemical properties of bimetallic nanocrystals are often highly adjustable and can be precisely designed by changing composition and optimizing structure according to need. Thus, a large amount of effort has been focused on synthesizing bimetallic nanocrystals with well-defined facets (e.g., cube, tetrahedron, octahedron, rhombic dodecahedron, and hexagonal plates) and special structure (core-shell, alloy and heterostructure).
Owing to the efforts of many scientists all over the world in recent years [16][17][18][19][20], many effective synthetic strategies have been developed, which are able to prepare a variety of bimetallic nanocrystals with different structures and components. The properties of bimetallic nanocatalysts including activity, selectivity and stability, have been proved to be not only related to the composition and size of the particles, but also related to the types of nanostructures. Huang and co-workers demonstrated that PdPt nanocube exhibited higher activity towards the hydrogenation of nitrobenzene than PdPt tetrahedral, and Pt 51 Pd 49 is higher than others [21]. Obviously, it is an urgent task in this field to develop some liquidphase synthesis methods that can control nanocrystals with specific size, composition and morphology, and it has also become a frontier topic in the field of bimetallic catalysis.
Due to the excellent works of many research groups, some synthesis methods were optimized and new synthetic strategies were designed. In addition, the application fields of bimetallic nanocrystals have also been expanded. This review mainly covers the most recent developments of typical structure, synthesis methods, and the application in many important fields. In this review, there are 74 references to be cited for the periods 2011-2015 and 97 references for the periods 2016-2020. Bimetals containing only noble metals are involved in 72 references, and bimetals containing at least one non-noble metal (iron, nickel, cobalt, copper, tin and titanium) have 82 references, in which the most widely studied bimetal is PtNi (22 references). Transition metal Ni has been proved an excellent additive in Pt-based catalysts, and Pt-Ni alloy nanocrystals are effective catalysts for electrocatalysis and heterogeneous catalysis due to the adjustable electronic structure, morphology and stoichiometry. In addition, it is worth noting that some related review articles of bimetals have been published about liquid-phase synthesis [17], shape-controlled synthesis [22], magnetic and optical properties and applications [16], magnetic and optical properties for biological applications [23], SPR and LSPR properties for photo catalysis [24] and sensing [25], and theory to applications [19]. These reviews fully illustrate the importance of the research field of bimetallic nanocrystals. In addition, we try our best to avoid overlap in preparing this review. Compared to other related reviews, this article will focus on controllable synthesis of typical bimetallic nanostructures and highlighting the most recent advance in some hot fields such as catalysis, energy conversion, sensing and bio-detection applications by selecting the represent articles.

The Structures of Bimetallic Nanocrystals
Despite only two elements, the architecture of bimetallic nanocrystals are complicated and multiform. According to the atomic ordering and configuration of two different metals, bimetallic nanostructures can be classified into three main types: alloyed structures (intermetallic and solid solution) and core-shell and heterostructure, as displayed in Figure 2. Due to the different raw materials and synthesis conditions, these nanostructures can also expose various crystal faces, including low Miller index surface, high Miller index step surface or their mixed crystal faces. In addition, the structure of bimetallic nanocrystals can be also divided into 0-D, 1-D and 2-D structures according to the three-dimensional extension of nanocrystals, as shown in Table 1. The zero-dimensional structure means that the expansion of the crystal in the three-dimensional direction is the same order of magnitude, mainly including regular polyhedrons and Wulff polyhedrons. One-dimensional structure refers to that the extension length of the crystal in one dimension is much greater than the extension length of the other two dimensions, mainly includes nanowires, nanorods, and so on. A two-dimensional structure implies that the stretched length of crystals in two dimensions is much greater than that of another dimension, mainly including nanoplates, nanosheets, and nanobelts etc. In addition, many derivative structures (core-frame, nanoboxes and nanocages) are reported in the literature.

Alloyed Structure
It has been proved that alloyed materials often exhibit unique physicochemical properties, not just the simple addition of the intrinsic properties of two distinct metals [49][50][51]. Alloyed structures of bimetallic nanocrystals are homogeneous mixtures with specific geometric arrangement of atoms, and metal bonds are formed between metal atoms. On the basis of atomic ordering, an alloyed structure can be divided into intermetallic compound and solid solution. The components in intermetallic compound alloys are bonded to each other to form compounds, so they have both long-range atomic order and definite atomic ratio. For a solid solution alloy, the components dissolve each other and the metal atoms randomly and thoroughly mixed. In the powder XRD pattern, the characteristic diffraction peak of single metal will disappear, and the alloy diffraction peak different from the two pure metal components will appear. The classification is highly significant because solid solution and intermetallic compounds often exhibit distinct performance even though they have the same elemental composition and stoichiometry.
For preparing the solid solution alloy, the most commonly used method is based on co-reduction (see Section 3.1). Although this method could effectively control the atomic ratio of products, it does not perform well in controlling the morphology and atomic order of nanocrystals. [16] The alloy structure of two metals (C and D) will be favored if three factors can be met: (i) relative strengths of C-D bond is higher than both the C-C and D-D bonds; (ii) similar surface energies of the individual bulk metals (C and D); and (iii) approximate atomic sizes and similar crystal structure [19]. It has been well proved properties, not just the simple addition of the intrinsic properties of two distinct metals [49][50][51]. Alloyed structures of bimetallic nanocrystals are homogeneous mixtures with specific geometric arrangement of atoms, and metal bonds are formed between metal atoms. On the basis of atomic ordering, an alloyed structure can be divided into intermetallic compound and solid solution. The components in intermetallic compound alloys are bonded to each other to form compounds, so they have both long-range atomic order and definite atomic ratio. For a solid solution alloy, the components dissolve each other and the metal atoms randomly and thoroughly mixed. In the powder XRD pattern, the characteristic diffraction peak of single metal will disappear, and the alloy diffraction peak different from the two pure metal components will appear. The classification is highly significant because solid solution and intermetallic compounds often exhibit distinct performance even though they have the same elemental composition and stoichiometry.
For preparing the solid solution alloy, the most commonly used method is based on co-reduction (see Section 3.1). Although this method could effectively control the atomic ratio of products, it does not perform well in controlling the morphology and atomic order of nanocrystals. [16] The alloy structure of two metals (C and D) will be favored if three factors can be met: (i) relative strengths of C-D bond is higher than both the C-C and D-D bonds; (ii) similar surface energies of the individual bulk metals (C and D); and (iii) approximate atomic sizes and similar crystal structure [19]. It has been well proved PtCo [37], PtCu [38], PdPt [39] Two-dimensional

Triangular plates
Pd@Pt [40], Ag-Pd [41] Hexagonal plates Pd@Pt [40], PdAg [42] Hollow structure Nanoframework CuPd [43], PdRh [44] Nanocage PdPt [45], PtNi [46] PdCu [47], AuAg [48] 2.1. Alloyed Structure It has been proved that alloyed materials often exhibit unique physicochemical properties, not just the simple addition of the intrinsic properties of two distinct metals [49][50][51]. Alloyed structures of bimetallic nanocrystals are homogeneous mixtures with specific geometric arrangement of atoms, and metal bonds are formed between metal atoms. On the basis of atomic ordering, an alloyed structure can be divided into intermetallic compound and solid solution. The components in intermetallic compound alloys are bonded to each other to form compounds, so they have both long-range atomic order and definite atomic ratio. For a solid solution alloy, the components dissolve each other and the metal atoms randomly and thoroughly mixed. In the powder XRD pattern, the characteristic diffraction peak of single metal will disappear, and the alloy diffraction peak different from the two pure metal components will appear. The classification is highly significant because solid solution and intermetallic compounds often exhibit distinct performance even though they have the same elemental composition and stoichiometry.
For preparing the solid solution alloy, the most commonly used method is based on co-reduction (see Section 3.1). Although this method could effectively control the atomic ratio of products, it does not perform well in controlling the morphology and atomic order of nanocrystals [16]. The alloy structure of two metals (C and D) will be favored if three Nanomaterials 2021, 11, 1926 5 of 37 factors can be met: (i) relative strengths of C-D bond is higher than both the C-C and D-D bonds; (ii) similar surface energies of the individual bulk metals (C and D); and (iii) approximate atomic sizes and similar crystal structure [19]. It has been well proved that the atomic arrangement in nanoalloys strictly depends on the balance of the factors outlined above, and is also related to the experimental conditions and synthetic strategies.
Some bimetallic systems might tend to form new crystalline structures distinct from a single metal, and exhibit strict atomic arrangements rather than random mixing, such as PtCu 3 [52], Pt 3 Ti [53], Pt 3 Sn [54], Ni 3 Sn 2 [55], and PtFe [56]. Thermodynamically, the final atomic arrangements in bimetal can be predicted by the change in Gibbs free energy upon mixing (∆G mix ) under a certain condition. For an ideal binary system, ∆G mix can be expressed by [57] ∆G mix = ∆H mix − T∆S mix (1) where T is reaction temperature, ∆H mix and ∆S mix are the changes of enthalpy and entropy before and after the reaction, respectively. In principle, the more negative the ∆G mix , the easier it is for two metal atoms to be mutually soluble. In most case, however, intermetallic compounds are difficult to obtain by a liquid method, which tends to produce solid solution alloys with disordered atomic arrangements. Thus, in order to obtain intermetallic compounds from alloys, some post-treatment processes (high temperature heat treatment under inert gas protection) are often needed [53,58,59]. Intermetallic compounds often exhibit improved catalytic and magnetic properties over that of alloys due to the precise control of composition and surface atomic arrangement [60,61]. Hideki and co-workers prepared atomically disordered Pt 3 Ti nanoparticles by co-reduction method, and atomically disordered Pt 3 Ti nanoparticles could transfer into atomically ordered Pt 3 Ti nanoparticles by annealing in vacuum at 600 • C. Both materials were used as the electrocatalyst for fuel cells, and the results showed that Pt 3 Ti NPs with highly ordered atomic arrangements exhibited higher current densities for formic acid oxidation than that of atomically disordered Pt 3 Ti NPs [53]. Considering the magnetic properties, intermetallic compounds consisting of one 3d metal (such as Fe, Co, Ni) and one 4d or 5d metal (such as Pd, Pt) have been distinguished, which exhibited excellent performance in the field of information storage [16]. Above all, bimetallic nanocrystals composited of intermetallic compounds have broad prospects in catalytic, energy conversion and storage, and sensing applications.

Core-Shell Structure
In recent years, bimetallic nanocrystals with the core-shell structure have drawn widespread attention because of their improved performance over the combination of the two distinct metals in catalytic, energy and sensing applications. The core-shell structure (C@D) is an ordered assembly structure, which is composed of an inner core (metal C) completely coated with a shell (metal D) by chemical bonds or other forces [62]. When the precursors of the two metal ions have different reducing abilities, the precursor with the higher reduction potential could be preferentially reduced to the metal atom and form the nucleation center, and then the metal ions with the lower potential are reduced to metal atoms and deposited on the nucleation center, finally forming the core-shell structure ( Figure 3). The most effective method to synthesize a core-shell structure is seed-mediated growth, in which metal C is often preferentially reduced and then acts as a heterogeneous nucleation site for metal D atoms to grow by chemical reduction or thermal decomposition methods [63][64][65][66]. The bimetals with multilayered nanostructures can be also generated by repeating the above process. After the efforts of many researchers, the nice thing is that the shell thickness of bimetal with core-shell structure could be precisely controlled at the atomic level [67,68], which is appealing for some special physicochemical properties, such as tuning optical properties, improvement in catalytic activity and stability, and augmenting of magnetic anisotropy. The core-shell structure has many morphologies due to the diverse morphologies of the seed (such as nanorod, nanowire, nanosphere, nanoplate, and polyhedra). In addition, the core-shell structure has many derived structures, such as mul- Figure 3. Different core-shell structures bimetallic nanocrystals: (a) spherical core-shell; (b) hexagonal core-shell; (c) multiple core with one shell; (d) multilayered core-shell; (e) yolk-shell [59].
The catalytic activities of the core-shell structured nanocrystals mainly depend on the composition of the shell metal, showing a catalytic effect similar to that of the single shell metal. Due to the poor electronegativity between the inner and outer metals, there will be electron transfer at the interface between the two distinct metals. Moreover, many researchers have paid attention to the dependence of atomic layer number on catalytic performance for bimetallic nanocrystals [69,70]. When the shell metal has only a single atomic layer, strain effect and electronic coupling effect are very significant, which could affect the catalytic properties including activity and selectivity of the shell metal. In this case, the system has the highest utilization efficiency of shell atoms, so that the material cost of surface atoms is the lowest. When the thickness of shell metal increases to multiple (2-6) atomic layers, strain and electronic coupling effect of core and shell atoms can still exist. Wang and co-workers studied the shell thickness-dependent catalytic activity of Pd@Pt nL core−shell icosahedra, and result showed a volcano-shaped curve, and the optimal shell thickness is 2.7 nm [69]. When the thickness of the outer metal (metal D) is greater than six atomic layers (or more than 1.5 nm), some special properties of bimetal (strain and electronic coupling effect) may disappear, and thus the ability to modulate their catalytic properties is lost. However, other excellent properties about multilayer core-shell bimetallic nanocrystals are reflected, such as adjusting the optical properties, and improving the catalytic activity and selectivity of bimetallic catalyst. The above results, as well as other studies, fully proved the importance of accurate control of shell thickness in preparing a core-shell bimetal (C@D) for practical application.

Heterostructure
When a metal atom is deposited on the surface of a substrate composed of another metal, there are three growth modes, namely, layer-layer growth mode, film-island growth mode, and island growth mode. When the D-D bond energy of metal D is greater than the C-D bond energy between metal C and metal D, or the specific surface free energy of D is greater than the specific surface free energy of C, D will choose the island growth mode because it can reduce the lattice stress between C and D and the total surface free energy. Simply put, when a metal preferentially generates nanocrystals with a certain morphology, and another metal atom adopts an "island growth mode" on the crystal, a multi-level structure will be formed ( Figure 2d). For example, the Tsung research group synthesized PdRh heterostructure nanocrystals by Pd seeds [71]. Because the bond dissociation energy of Rh-Rh is greater than that of Rh-Pd, the Rh atoms generated by subsequent reduction will choose "island growth mode" on Pd nanocrystal surface (as shown in Figure 4). The characteristics of heterostructure nanocrystals are similar to those of the mixture formed by mixing metal nanocrystals with corresponding sizes. The XRD pattern of the heterostructure bimetallic nanocrystals will have the same metal characteristic peaks as the two-metal mixture. On the one hand, the bimetallic nanocrystals with multi-level structure may retain the physical and chemical properties of the two distinct metals in the metal mixture; on the other hand, due to the interface interaction between multi-level structures, they will have some new properties different from the metal mixture in some systems [72,73].

Core-Frame and Other Derivative Structure
In addition to the three basic nanostructures mentioned above, there are many derivative nanostructures, such as core-frame [18,74,75], nanodimers [76], hollow nanoboxes [77] and nanocages [78,79], and dendritic structure [80]. As we all know, the specific surface area and number of active catalytic sites must be maximized for effective catalysis. Compared with other structures, bimetallic nanocrystals with core-frame structure possess the maximum surface area per volume (high atomic efficiency) due to the hollow nanostructures with openings in their shells, which exhibited excellent electrocatalytic activity in terms of the oxygen reduction reaction (ORR), oxygen evolution reaction (OER), hydrogen evolution reaction (HER), and methanol oxidation reaction (MOR). Several research groups, including Xia and Lee, have done a lot of works on preparing the bimetallic nanocrystals with core-frame structure. The synthetic routes of nanoframes mainly include presynthesized template-assisted and solvothermal route involving in situ formed template. The second metal is grown on the template, and then the template is removed by acid etching or electric displacement to obtain a bimetal frame structure. Metals commonly used as templates are noble metals (Pd [81], Ag [82][83][84] and Au [75,85]) and transition metal (Cu [86][87][88] and Ni [89,90]). Some synthesized frame structures developed up until now are shown in Figure 5. The frame structures, including nanoboxes and nanocages, are the highly open structures with large specific surface area and atomic utilization, which often exhibit high catalytic activity and tunable spectral properties. Therefore, the nanocrystals with the open frame structures have been employed in many practical applications in some advanced fields, such as drug-delivery [91], photothermal cancer therapy [92], bio-imaging, sensing [93], fuel cell [90] and many others. However, there are shortcomings and limitations that need further study, such as instability.

Controllable Synthesis of Bimetallic Nanocrystals
It has been proved that the natural properties of bimetallic nanocrystals are closely related to their composition, size and shape. Xia and co-workers prepared Pd, PdPt and PdAu bimetallic nanocrystals with the same morphology by a seeded growth method for catalytic oxidation of formic acid, and the result showed that Pd concave decahedra exhibited improved catalytic activity, which was attributed to the high-index facets and twin boundaries on the Pd surface [105]. Therefore, the controllable synthesis of bimetallic nanocrystals is of great significance for further optimizing their functionality and application performance. Generally speaking, the growth process of bimetallic nanocrystals can be divided into two stages: nucleation and growth. The two processes are often continuous and difficult to separate, and the thermodynamic and kinetic processes of these two stages are often difficult to control, so the controllable synthesis of bimetallic nanocrystals becomes very complex. In the whole synthesis process, reaction temperature, environmental pressure and reaction time will affect the morphology of the crystal. In addition, the type, concentration and reduction potential of reactants, reducing agent and the surfactant will also affect the reduction rate of reactants and the nucleation and growth process of nanocrystals [17,106]. Thanks to the efforts of many research groups, many synthesis strategies have been developed to obtain bimetallic nanocrystals with well-controlled properties. It is worth noting that different synthesis methods also may produce the products with similar structure owing to the similarity of basic mechanisms or reaction pathways. The complex nanostructures are generally synthesized by a combination of two or more different synthetic methods. This paper will focus on the typical and most used synthetic strategies, including co-reduction, seed-mediated growth, thermal decomposition, and galvanic replacement reaction.

Co-Reduction
The co-reduction method entails that the precursors of two metal ions can be reduced simultaneously under certain reaction conditions, and then nucleate and grow into nanocrystals. The method is considered to be the most simple and straightforward strategy to prepare the bimetal with alloyed or intermetallic nanostructures [16] (Figure 6). However, core-shell and heterostructure also can be obtained by this method under certain condition. According to the study of LaMer [107], nucleation and growth should be divided into two distinct processes in order to obtain highly monodispersed nanocrystals. The nucleation and growth process of bimetallic nanoparticles mainly depends on the reduction rate of metal ions precursors, which is closely related to the reduction potential of metal ions. It is known that the higher reduction potential of metal ions, the easier the metal ions are to be reduced. The reduction potentials of the metal ions are shown in Table 2. Generally, metals with similar reduction potentials tend to form alloys. The two metals with large difference in reduction potential tend to form bimetallic with core-shell structure or heterostructure. In addition, the composition and shape of bimetals are related to the reactants (precursor, reducing agent and surfactant) and the reaction conditions (temperature, pressure and so on). According to the different reaction routes and conditions, the co-reduction method can be divided into solvothermal methods and oil-phase methods.  Table 2. Reduction potentials of the metal ions [16].

Reduction Reaction E o (V vs. SHE) a
Au 3+ + 3e − lic nanocrystals is of great significance for further optimizing their functionality and application performance. Generally speaking, the growth process of bimetallic nanocrystals can be divided into two stages: nucleation and growth. The two processes are often continuous and difficult to separate, and the thermodynamic and kinetic processes of these two stages are often difficult to control, so the controllable synthesis of bimetallic nanocrystals becomes very complex. In the whole synthesis process, reaction temperature, environmental pressure and reaction time will affect the morphology of the crystal. In addition, the type, concentration and reduction potential of reactants, reducing agent and the surfactant will also affect the reduction rate of reactants and the nucleation and growth process of nanocrystals [17,106]. Thanks to the efforts of many research groups, many synthesis strategies have been developed to obtain bimetallic nanocrystals with well-controlled properties. It is worth noting that different synthesis methods also may produce the products with similar structure owing to the similarity of basic mechanisms or reaction pathways. The complex nanostructures are generally synthesized by a combination of two or more different synthetic methods. This paper will focus on the typical and most used synthetic strategies, including co-reduction, seed-mediated growth, thermal decomposition, and galvanic replacement reaction.

Co-Reduction
The co-reduction method entails that the precursors of two metal ions can be reduced simultaneously under certain reaction conditions, and then nucleate and grow into nanocrystals. The method is considered to be the most simple and straightforward strategy to prepare the bimetal with alloyed or intermetallic nanostructures [16] ( Figure  6). However, core-shell and heterostructure also can be obtained by this method under certain condition. According to the study of LaMer [107], nucleation and growth should be divided into two distinct processes in order to obtain highly monodispersed nanocrystals. The nucleation and growth process of bimetallic nanoparticles mainly depends on the reduction rate of metal ions precursors, which is closely related to the reduction potential of metal ions. It is known that the higher reduction potential of metal ions, the easier the metal ions are to be reduced. The reduction potentials of the metal ions are shown in Table 2. Generally, metals with similar reduction potentials tend to form alloys. The two metals with large difference in reduction potential tend to form bimetallic with core-shell structure or heterostructure. In addition, the composition and shape of bimetals are related to the reactants (precursor, reducing agent and surfactant) and the reaction conditions (temperature, pressure and so on). According to the different reaction routes and conditions, the co-reduction method can be divided into solvothermal methods and oil-phase methods.  lic nanocrystals is of great significance for further optimizing their functionality and application performance. Generally speaking, the growth process of bimetallic nanocrystals can be divided into two stages: nucleation and growth. The two processes are often continuous and difficult to separate, and the thermodynamic and kinetic processes of these two stages are often difficult to control, so the controllable synthesis of bimetallic nanocrystals becomes very complex. In the whole synthesis process, reaction temperature, environmental pressure and reaction time will affect the morphology of the crystal. In addition, the type, concentration and reduction potential of reactants, reducing agent and the surfactant will also affect the reduction rate of reactants and the nucleation and growth process of nanocrystals [17,106]. Thanks to the efforts of many research groups, many synthesis strategies have been developed to obtain bimetallic nanocrystals with well-controlled properties. It is worth noting that different synthesis methods also may produce the products with similar structure owing to the similarity of basic mechanisms or reaction pathways. The complex nanostructures are generally synthesized by a combination of two or more different synthetic methods. This paper will focus on the typical and most used synthetic strategies, including co-reduction, seed-mediated growth, thermal decomposition, and galvanic replacement reaction.

Co-Reduction
The co-reduction method entails that the precursors of two metal ions can be reduced simultaneously under certain reaction conditions, and then nucleate and grow into nanocrystals. The method is considered to be the most simple and straightforward strategy to prepare the bimetal with alloyed or intermetallic nanostructures [16] ( Figure  6). However, core-shell and heterostructure also can be obtained by this method under certain condition. According to the study of LaMer [107], nucleation and growth should be divided into two distinct processes in order to obtain highly monodispersed nanocrystals. The nucleation and growth process of bimetallic nanoparticles mainly depends on the reduction rate of metal ions precursors, which is closely related to the reduction potential of metal ions. It is known that the higher reduction potential of metal ions, the easier the metal ions are to be reduced. The reduction potentials of the metal ions are shown in Table 2. Generally, metals with similar reduction potentials tend to form alloys. The two metals with large difference in reduction potential tend to form bimetallic with core-shell structure or heterostructure. In addition, the composition and shape of bimetals are related to the reactants (precursor, reducing agent and surfactant) and the reaction conditions (temperature, pressure and so on). According to the different reaction routes and conditions, the co-reduction method can be divided into solvothermal methods and oil-phase methods.  lic nanocrystals is of great significance for further optimizing their functionality and application performance. Generally speaking, the growth process of bimetallic nanocrystals can be divided into two stages: nucleation and growth. The two processes are often continuous and difficult to separate, and the thermodynamic and kinetic processes of these two stages are often difficult to control, so the controllable synthesis of bimetallic nanocrystals becomes very complex. In the whole synthesis process, reaction temperature, environmental pressure and reaction time will affect the morphology of the crystal. In addition, the type, concentration and reduction potential of reactants, reducing agent and the surfactant will also affect the reduction rate of reactants and the nucleation and growth process of nanocrystals [17,106]. Thanks to the efforts of many research groups, many synthesis strategies have been developed to obtain bimetallic nanocrystals with well-controlled properties. It is worth noting that different synthesis methods also may produce the products with similar structure owing to the similarity of basic mechanisms or reaction pathways. The complex nanostructures are generally synthesized by a combination of two or more different synthetic methods. This paper will focus on the typical and most used synthetic strategies, including co-reduction, seed-mediated growth, thermal decomposition, and galvanic replacement reaction.

Co-Reduction
The co-reduction method entails that the precursors of two metal ions can be reduced simultaneously under certain reaction conditions, and then nucleate and grow into nanocrystals. The method is considered to be the most simple and straightforward strategy to prepare the bimetal with alloyed or intermetallic nanostructures [16] ( Figure  6). However, core-shell and heterostructure also can be obtained by this method under certain condition. According to the study of LaMer [107], nucleation and growth should be divided into two distinct processes in order to obtain highly monodispersed nanocrystals. The nucleation and growth process of bimetallic nanoparticles mainly depends on the reduction rate of metal ions precursors, which is closely related to the reduction potential of metal ions. It is known that the higher reduction potential of metal ions, the easier the metal ions are to be reduced. The reduction potentials of the metal ions are shown in Table 2. Generally, metals with similar reduction potentials tend to form alloys. The two metals with large difference in reduction potential tend to form bimetallic with core-shell structure or heterostructure. In addition, the composition and shape of bimetals are related to the reactants (precursor, reducing agent and surfactant) and the reaction conditions (temperature, pressure and so on). According to the different reaction routes and conditions, the co-reduction method can be divided into solvothermal methods and oil-phase methods.  lic nanocrystals is of great significance for further optimizing their functionality and application performance. Generally speaking, the growth process of bimetallic nanocrystals can be divided into two stages: nucleation and growth. The two processes are often continuous and difficult to separate, and the thermodynamic and kinetic processes of these two stages are often difficult to control, so the controllable synthesis of bimetallic nanocrystals becomes very complex. In the whole synthesis process, reaction temperature, environmental pressure and reaction time will affect the morphology of the crystal. In addition, the type, concentration and reduction potential of reactants, reducing agent and the surfactant will also affect the reduction rate of reactants and the nucleation and growth process of nanocrystals [17,106]. Thanks to the efforts of many research groups, many synthesis strategies have been developed to obtain bimetallic nanocrystals with well-controlled properties. It is worth noting that different synthesis methods also may produce the products with similar structure owing to the similarity of basic mechanisms or reaction pathways. The complex nanostructures are generally synthesized by a combination of two or more different synthetic methods. This paper will focus on the typical and most used synthetic strategies, including co-reduction, seed-mediated growth, thermal decomposition, and galvanic replacement reaction.

Co-Reduction
The co-reduction method entails that the precursors of two metal ions can be reduced simultaneously under certain reaction conditions, and then nucleate and grow into nanocrystals. The method is considered to be the most simple and straightforward strategy to prepare the bimetal with alloyed or intermetallic nanostructures [16] ( Figure  6). However, core-shell and heterostructure also can be obtained by this method under certain condition. According to the study of LaMer [107], nucleation and growth should be divided into two distinct processes in order to obtain highly monodispersed nanocrystals. The nucleation and growth process of bimetallic nanoparticles mainly depends on the reduction rate of metal ions precursors, which is closely related to the reduction potential of metal ions. It is known that the higher reduction potential of metal ions, the easier the metal ions are to be reduced. The reduction potentials of the metal ions are shown in Table 2. Generally, metals with similar reduction potentials tend to form alloys. The two metals with large difference in reduction potential tend to form bimetallic with core-shell structure or heterostructure. In addition, the composition and shape of bimetals are related to the reactants (precursor, reducing agent and surfactant) and the reaction conditions (temperature, pressure and so on). According to the different reaction routes and conditions, the co-reduction method can be divided into solvothermal methods and oil-phase methods.  lic nanocrystals is of great significance for further optimizing their functionality and application performance. Generally speaking, the growth process of bimetallic nanocrystals can be divided into two stages: nucleation and growth. The two processes are often continuous and difficult to separate, and the thermodynamic and kinetic processes of these two stages are often difficult to control, so the controllable synthesis of bimetallic nanocrystals becomes very complex. In the whole synthesis process, reaction temperature, environmental pressure and reaction time will affect the morphology of the crystal. In addition, the type, concentration and reduction potential of reactants, reducing agent and the surfactant will also affect the reduction rate of reactants and the nucleation and growth process of nanocrystals [17,106]. Thanks to the efforts of many research groups, many synthesis strategies have been developed to obtain bimetallic nanocrystals with well-controlled properties. It is worth noting that different synthesis methods also may produce the products with similar structure owing to the similarity of basic mechanisms or reaction pathways. The complex nanostructures are generally synthesized by a combination of two or more different synthetic methods. This paper will focus on the typical and most used synthetic strategies, including co-reduction, seed-mediated growth, thermal decomposition, and galvanic replacement reaction.

Co-Reduction
The co-reduction method entails that the precursors of two metal ions can be reduced simultaneously under certain reaction conditions, and then nucleate and grow into nanocrystals. The method is considered to be the most simple and straightforward strategy to prepare the bimetal with alloyed or intermetallic nanostructures [16] ( Figure  6). However, core-shell and heterostructure also can be obtained by this method under certain condition. According to the study of LaMer [107], nucleation and growth should be divided into two distinct processes in order to obtain highly monodispersed nanocrystals. The nucleation and growth process of bimetallic nanoparticles mainly depends on the reduction rate of metal ions precursors, which is closely related to the reduction potential of metal ions. It is known that the higher reduction potential of metal ions, the easier the metal ions are to be reduced. The reduction potentials of the metal ions are shown in Table 2. Generally, metals with similar reduction potentials tend to form alloys. The two metals with large difference in reduction potential tend to form bimetallic with core-shell structure or heterostructure. In addition, the composition and shape of bimetals are related to the reactants (precursor, reducing agent and surfactant) and the reaction conditions (temperature, pressure and so on). According to the different reaction routes and conditions, the co-reduction method can be divided into solvothermal methods and oil-phase methods.  lic nanocrystals is of great significance for further optimizing their functionality and application performance. Generally speaking, the growth process of bimetallic nanocrystals can be divided into two stages: nucleation and growth. The two processes are often continuous and difficult to separate, and the thermodynamic and kinetic processes of these two stages are often difficult to control, so the controllable synthesis of bimetallic nanocrystals becomes very complex. In the whole synthesis process, reaction temperature, environmental pressure and reaction time will affect the morphology of the crystal. In addition, the type, concentration and reduction potential of reactants, reducing agent and the surfactant will also affect the reduction rate of reactants and the nucleation and growth process of nanocrystals [17,106]. Thanks to the efforts of many research groups, many synthesis strategies have been developed to obtain bimetallic nanocrystals with well-controlled properties. It is worth noting that different synthesis methods also may produce the products with similar structure owing to the similarity of basic mechanisms or reaction pathways. The complex nanostructures are generally synthesized by a combination of two or more different synthetic methods. This paper will focus on the typical and most used synthetic strategies, including co-reduction, seed-mediated growth, thermal decomposition, and galvanic replacement reaction.

Co-Reduction
The co-reduction method entails that the precursors of two metal ions can be reduced simultaneously under certain reaction conditions, and then nucleate and grow into nanocrystals. The method is considered to be the most simple and straightforward strategy to prepare the bimetal with alloyed or intermetallic nanostructures [16] ( Figure  6). However, core-shell and heterostructure also can be obtained by this method under certain condition. According to the study of LaMer [107], nucleation and growth should be divided into two distinct processes in order to obtain highly monodispersed nanocrystals. The nucleation and growth process of bimetallic nanoparticles mainly depends on the reduction rate of metal ions precursors, which is closely related to the reduction potential of metal ions. It is known that the higher reduction potential of metal ions, the easier the metal ions are to be reduced. The reduction potentials of the metal ions are shown in Table 2. Generally, metals with similar reduction potentials tend to form alloys. The two metals with large difference in reduction potential tend to form bimetallic with core-shell structure or heterostructure. In addition, the composition and shape of bimetals are related to the reactants (precursor, reducing agent and surfactant) and the reaction conditions (temperature, pressure and so on). According to the different reaction routes and conditions, the co-reduction method can be divided into solvothermal methods and oil-phase methods.  lic nanocrystals is of great significance for further optimizing their functionality and application performance. Generally speaking, the growth process of bimetallic nanocrystals can be divided into two stages: nucleation and growth. The two processes are often continuous and difficult to separate, and the thermodynamic and kinetic processes of these two stages are often difficult to control, so the controllable synthesis of bimetallic nanocrystals becomes very complex. In the whole synthesis process, reaction temperature, environmental pressure and reaction time will affect the morphology of the crystal. In addition, the type, concentration and reduction potential of reactants, reducing agent and the surfactant will also affect the reduction rate of reactants and the nucleation and growth process of nanocrystals [17,106]. Thanks to the efforts of many research groups, many synthesis strategies have been developed to obtain bimetallic nanocrystals with well-controlled properties. It is worth noting that different synthesis methods also may produce the products with similar structure owing to the similarity of basic mechanisms or reaction pathways. The complex nanostructures are generally synthesized by a combination of two or more different synthetic methods. This paper will focus on the typical and most used synthetic strategies, including co-reduction, seed-mediated growth, thermal decomposition, and galvanic replacement reaction.

Co-Reduction
The co-reduction method entails that the precursors of two metal ions can be reduced simultaneously under certain reaction conditions, and then nucleate and grow into nanocrystals. The method is considered to be the most simple and straightforward strategy to prepare the bimetal with alloyed or intermetallic nanostructures [16] ( Figure  6). However, core-shell and heterostructure also can be obtained by this method under certain condition. According to the study of LaMer [107], nucleation and growth should be divided into two distinct processes in order to obtain highly monodispersed nanocrystals. The nucleation and growth process of bimetallic nanoparticles mainly depends on the reduction rate of metal ions precursors, which is closely related to the reduction potential of metal ions. It is known that the higher reduction potential of metal ions, the easier the metal ions are to be reduced. The reduction potentials of the metal ions are shown in Table 2. Generally, metals with similar reduction potentials tend to form alloys. The two metals with large difference in reduction potential tend to form bimetallic with core-shell structure or heterostructure. In addition, the composition and shape of bimetals are related to the reactants (precursor, reducing agent and surfactant) and the reaction conditions (temperature, pressure and so on). According to the different reaction routes and conditions, the co-reduction method can be divided into solvothermal methods and oil-phase methods.  lic nanocrystals is of great significance for further optimizing their functionality and application performance. Generally speaking, the growth process of bimetallic nanocrystals can be divided into two stages: nucleation and growth. The two processes are often continuous and difficult to separate, and the thermodynamic and kinetic processes of these two stages are often difficult to control, so the controllable synthesis of bimetallic nanocrystals becomes very complex. In the whole synthesis process, reaction temperature, environmental pressure and reaction time will affect the morphology of the crystal. In addition, the type, concentration and reduction potential of reactants, reducing agent and the surfactant will also affect the reduction rate of reactants and the nucleation and growth process of nanocrystals [17,106]. Thanks to the efforts of many research groups, many synthesis strategies have been developed to obtain bimetallic nanocrystals with well-controlled properties. It is worth noting that different synthesis methods also may produce the products with similar structure owing to the similarity of basic mechanisms or reaction pathways. The complex nanostructures are generally synthesized by a combination of two or more different synthetic methods. This paper will focus on the typical and most used synthetic strategies, including co-reduction, seed-mediated growth, thermal decomposition, and galvanic replacement reaction.

Co-Reduction
The co-reduction method entails that the precursors of two metal ions can be reduced simultaneously under certain reaction conditions, and then nucleate and grow into nanocrystals. The method is considered to be the most simple and straightforward strategy to prepare the bimetal with alloyed or intermetallic nanostructures [16] ( Figure  6). However, core-shell and heterostructure also can be obtained by this method under certain condition. According to the study of LaMer [107], nucleation and growth should be divided into two distinct processes in order to obtain highly monodispersed nanocrystals. The nucleation and growth process of bimetallic nanoparticles mainly depends on the reduction rate of metal ions precursors, which is closely related to the reduction potential of metal ions. It is known that the higher reduction potential of metal ions, the easier the metal ions are to be reduced. The reduction potentials of the metal ions are shown in Table 2. Generally, metals with similar reduction potentials tend to form alloys. The two metals with large difference in reduction potential tend to form bimetallic with core-shell structure or heterostructure. In addition, the composition and shape of bimetals are related to the reactants (precursor, reducing agent and surfactant) and the reaction conditions (temperature, pressure and so on). According to the different reaction routes and conditions, the co-reduction method can be divided into solvothermal methods and oil-phase methods.  lic nanocrystals is of great significance for further optimizing their functionality and application performance. Generally speaking, the growth process of bimetallic nanocrystals can be divided into two stages: nucleation and growth. The two processes are often continuous and difficult to separate, and the thermodynamic and kinetic processes of these two stages are often difficult to control, so the controllable synthesis of bimetallic nanocrystals becomes very complex. In the whole synthesis process, reaction temperature, environmental pressure and reaction time will affect the morphology of the crystal. In addition, the type, concentration and reduction potential of reactants, reducing agent and the surfactant will also affect the reduction rate of reactants and the nucleation and growth process of nanocrystals [17,106]. Thanks to the efforts of many research groups, many synthesis strategies have been developed to obtain bimetallic nanocrystals with well-controlled properties. It is worth noting that different synthesis methods also may produce the products with similar structure owing to the similarity of basic mechanisms or reaction pathways. The complex nanostructures are generally synthesized by a combination of two or more different synthetic methods. This paper will focus on the typical and most used synthetic strategies, including co-reduction, seed-mediated growth, thermal decomposition, and galvanic replacement reaction.

Co-Reduction
The co-reduction method entails that the precursors of two metal ions can be reduced simultaneously under certain reaction conditions, and then nucleate and grow into nanocrystals. The method is considered to be the most simple and straightforward strategy to prepare the bimetal with alloyed or intermetallic nanostructures [16] ( Figure  6). However, core-shell and heterostructure also can be obtained by this method under certain condition. According to the study of LaMer [107], nucleation and growth should be divided into two distinct processes in order to obtain highly monodispersed nanocrystals. The nucleation and growth process of bimetallic nanoparticles mainly depends on the reduction rate of metal ions precursors, which is closely related to the reduction potential of metal ions. It is known that the higher reduction potential of metal ions, the easier the metal ions are to be reduced. The reduction potentials of the metal ions are shown in Table 2. Generally, metals with similar reduction potentials tend to form alloys. The two metals with large difference in reduction potential tend to form bimetallic with core-shell structure or heterostructure. In addition, the composition and shape of bimetals are related to the reactants (precursor, reducing agent and surfactant) and the reaction conditions (temperature, pressure and so on). According to the different reaction routes and conditions, the co-reduction method can be divided into solvothermal methods and oil-phase methods.  lic nanocrystals is of great significance for further optimizing their functionality and application performance. Generally speaking, the growth process of bimetallic nanocrystals can be divided into two stages: nucleation and growth. The two processes are often continuous and difficult to separate, and the thermodynamic and kinetic processes of these two stages are often difficult to control, so the controllable synthesis of bimetallic nanocrystals becomes very complex. In the whole synthesis process, reaction temperature, environmental pressure and reaction time will affect the morphology of the crystal. In addition, the type, concentration and reduction potential of reactants, reducing agent and the surfactant will also affect the reduction rate of reactants and the nucleation and growth process of nanocrystals [17,106]. Thanks to the efforts of many research groups, many synthesis strategies have been developed to obtain bimetallic nanocrystals with well-controlled properties. It is worth noting that different synthesis methods also may produce the products with similar structure owing to the similarity of basic mechanisms or reaction pathways. The complex nanostructures are generally synthesized by a combination of two or more different synthetic methods. This paper will focus on the typical and most used synthetic strategies, including co-reduction, seed-mediated growth, thermal decomposition, and galvanic replacement reaction.

Co-Reduction
The co-reduction method entails that the precursors of two metal ions can be reduced simultaneously under certain reaction conditions, and then nucleate and grow into nanocrystals. The method is considered to be the most simple and straightforward strategy to prepare the bimetal with alloyed or intermetallic nanostructures [16] ( Figure  6). However, core-shell and heterostructure also can be obtained by this method under certain condition. According to the study of LaMer [107], nucleation and growth should be divided into two distinct processes in order to obtain highly monodispersed nanocrystals. The nucleation and growth process of bimetallic nanoparticles mainly depends on the reduction rate of metal ions precursors, which is closely related to the reduction potential of metal ions. It is known that the higher reduction potential of metal ions, the easier the metal ions are to be reduced. The reduction potentials of the metal ions are shown in Table 2. Generally, metals with similar reduction potentials tend to form alloys. The two metals with large difference in reduction potential tend to form bimetallic with core-shell structure or heterostructure. In addition, the composition and shape of bimetals are related to the reactants (precursor, reducing agent and surfactant) and the reaction conditions (temperature, pressure and so on). According to the different reaction routes and conditions, the co-reduction method can be divided into solvothermal methods and oil-phase methods.  lic nanocrystals is of great significance for further optimizing their functionality and application performance. Generally speaking, the growth process of bimetallic nanocrystals can be divided into two stages: nucleation and growth. The two processes are often continuous and difficult to separate, and the thermodynamic and kinetic processes of these two stages are often difficult to control, so the controllable synthesis of bimetallic nanocrystals becomes very complex. In the whole synthesis process, reaction temperature, environmental pressure and reaction time will affect the morphology of the crystal. In addition, the type, concentration and reduction potential of reactants, reducing agent and the surfactant will also affect the reduction rate of reactants and the nucleation and growth process of nanocrystals [17,106]. Thanks to the efforts of many research groups, many synthesis strategies have been developed to obtain bimetallic nanocrystals with well-controlled properties. It is worth noting that different synthesis methods also may produce the products with similar structure owing to the similarity of basic mechanisms or reaction pathways. The complex nanostructures are generally synthesized by a combination of two or more different synthetic methods. This paper will focus on the typical and most used synthetic strategies, including co-reduction, seed-mediated growth, thermal decomposition, and galvanic replacement reaction.

Co-Reduction
The co-reduction method entails that the precursors of two metal ions can be reduced simultaneously under certain reaction conditions, and then nucleate and grow into nanocrystals. The method is considered to be the most simple and straightforward strategy to prepare the bimetal with alloyed or intermetallic nanostructures [16] ( Figure  6). However, core-shell and heterostructure also can be obtained by this method under certain condition. According to the study of LaMer [107], nucleation and growth should be divided into two distinct processes in order to obtain highly monodispersed nanocrystals. The nucleation and growth process of bimetallic nanoparticles mainly depends on the reduction rate of metal ions precursors, which is closely related to the reduction potential of metal ions. It is known that the higher reduction potential of metal ions, the easier the metal ions are to be reduced. The reduction potentials of the metal ions are shown in Table 2. Generally, metals with similar reduction potentials tend to form alloys. The two metals with large difference in reduction potential tend to form bimetallic with core-shell structure or heterostructure. In addition, the composition and shape of bimetals are related to the reactants (precursor, reducing agent and surfactant) and the reaction conditions (temperature, pressure and so on). According to the different reaction routes and conditions, the co-reduction method can be divided into solvothermal methods and oil-phase methods.

Solvothermal Method
This method immerses the reactant in water or organic solvent, and then it reacts for a period of time in a closed container at a specific temperature, which can effectively control the structure and crystal phase of the nanomaterial. This solvothermal reaction has unique advantages and broad application prospects. Under solvothermal conditions, the entire system is in a state of high temperature and high pressure, the solvent is in a subcritical state, and the solubility is enhanced, so the activity of the reactants is greatly improved, and metastable phases that are difficult to obtain under normal pressure can be prepared. The solvothermal reaction parameters are easy to adjust and the nanocrystals with higher crystallinity and small size distribution can be effectively obtained. In addition, the growth mode of nanocrystals is also related to crystal face selection reagents. Therefore, in the solvothermal process, surfactant can be added to control the morphology of nanocrystals. Different crystal planes have different atomic arrangements, and organic reagents and inorganic ions have different adsorption capacities on different crystal planes, so nanocrystals can be controlled to grow in a specific direction.
The general idea for the synthesis of water-soluble metal nanocrystals is to select appropriate metal precursors (metal inorganic salt), hydrophilic solvents, surface ligands (e.g., PVP or CTAB) and morphology control agents (small inorganic molecule). For example, Wu and co-workers successfully prepared Pt-Ni alloy (PtNi 2 ) nanocrystals with uniform size and morphology by solvothermal method [108]. The truncated octahedral nanocrystals can be controlled by the ratio of aniline to benzoic acid, and PdNi 2 nanocrystals could be obtained by introducing the KBr in the system (Figure 7). Other bimetallic nanocrystals (e.g., PdNi, PtCu, PdCu) were also obtained by the above method [108].

Oil Phase Method
When a high-boiling point solvent is used as a reaction medium, the metal precursor can nucleate explosively above the decomposition temperature, so the nucleation and growth stages can be better separated, which facilitates the preparation of nanocrystals with uniform size and good dispersion. Before the temperature rises, the reaction system can be evacuated; during the temperature rise and stability stage, an inert gas can be used to fill the system in order to exclude oxygen. Therefore, for the oxygen-sensitive preparation reaction process, the oil phase high temperature method has advantages that the hydrothermal reaction does not have. The high boiling point solvents are mostly long alkyl chain surfactants, which have a strong ability to coat nanoparticles. Therefore, it is necessary to eliminate the ligands on the surface before being applied to the catalytic reaction to release the catalytic active sites. For example, our group prepared Pt 2 Ni alloy@Pt nanocrystals (Figure 8) by using H 2 PtCl 6 · 6H 2 O and NiCl 2 ·6H 2 O as precursors and oleylamin as solvents and reducing agents [109]. Structure evolution of Pt 2 Ni alloy@Pt architectures were investigated by varying the precursor ratio. When Pt/Ni ratios were varied (1:2, 1:1, 2:1 and 3:1), the morphology of the products are shown as in Figure 8a-d. The different shapes can be ascribed to the increasing Pt concentration and different reduction potentials of Ni 2+ /Ni and Pt 4+ /Pt. The ORR performance exhibited that the order of catalytic activity is PtNi 2 < PtNi 2 @Pt < Pt 2 Ni < Pt 2 Ni@Pt.

Seed-Mediated Growth
Seed-mediated growth is an effective synthesis strategy to generate the bimetallic nanocrystals with well-defined structures that are difficult to obtain by other methods [110][111][112][113]. For example, bimetallic nanocrystals with core-shell or heterostructure could be easily synthesized by this method. The conceptual diagram of these two structures obtained by the seed growth method is shown in Figure 9. In this process, one metal is firstly synthesized as a seed, and then the other metals are uniformly deposited on the seeds surface and form a shell layer, resulting in a bimetallic nanocrystal with a core-shell structure; and if the second metal is only deposited and grown in the special sites of seed crystals, the bimetallic nanocrystal with a heterogeneous structure will be obtained. The seed-mediated growth method was first put forward in 2001 by Murphy, who prepared Au nanorods by using Au nanoparticles as seeds [114]. Soon after that, Xia's group prepared Ag nanowires by using Pt seeds [115]. In the next 10 years, the seed-mediated method was further expanded to prepare other bimetals (Pt@Pd [28], Au@Ag [116], Pd@Ag [117], and so on). The activation energy required for homogeneous nucleation is greater than that for growth. Therefore, when the solution contains pre-added seeds, the second metal ions will nucleate and grow heterogeneously on the seed surface after being reduced. This growth method has two growth modes: conformal epitaxial growth and non-conformal epitaxial growth. Different growth modes mainly depend on the reduction rate of metal ions, surface free energy, metal bond energy, and the choice of crystal plane stabilizing reagents. Yang and co-workers prepared Pt@Pd nanocrystals with different shapes (cubes, cuboctahedra, and octahedra) by using cubic Pt seeds [28]. They demonstrated whether the crystal lat-tice matches determined the growth mode of the crystal (isotropic growth or anisotropic growth). Lattice-matched Pd could produce conformal Pt@Pd core-shell nanocrystals, but Au grows anisotropically on the surface of Pt seeds due to distinctly different lattice parameters of Au and Pt. In addition, they found that the growth rates along different crystal directions could be altered by introducing NO 2 into the reaction system and Pd (100) direction grows faster than that of Pd (111). This may be ascribed to the fact that Pd catalyst could dissociate NO 2 to generate NO and atomic oxygen, and Pd (111) will adsorb dissociative oxygen and lead to partial passivation. After more than 10 years of hard work, this method has been widely used to prepare bimetallic nanocrystals with a core-shell structure. For example, our group synthesized Pd@Rh bimetallic nanocube by using Pd nanocube as seeds [118], and PdRh hollow nanoframes were obtained by etching Pd@Rh nanocube in HNO 3 aqueous solution (as shown in Figure 10).   [118]. Copyright American Chemical Society, 2020.

Thermal Decomposition
The principle of thermal decomposition is to heat organic metal compounds and decompose them to obtain metal nanoparticles. It is usually suitable for the preparation of metal nanoparticles with low reduction potential, and the method is a typical strategy for obtaining highly monodisperse nanocrystals. The thermal decomposition method was first proposed by the Thomas research group and used to prepare Ru-based bimetallic nanoparticles (RuPt, RuPd, RuSn and RuCu) [119]. Similar to the chemical reduction method, the composition, morphology and size of bimetallic nanoparticles prepared by thermal decomposition method are greatly affected by the proportion of metal precursors, the type of surfactant, solvent, reaction temperature and time.
Thermal decomposition has been demonstrated a simple and effective synthesis method to prepare various types of nanocrystals including mono-and bimetallic, and metal−oxide. It is known that the metal ion with relatively low reduction potential (such as Fe, Co, and Ni in Table 2) is difficult to reduce by chemical reduction method [120][121][122]. However, thermal decomposition can easily solve this problem. In the process of preparing bimetallic nanocrystals by the thermal decomposition method, some commonly used metal precursors mainly include the carbonyls (M(CO) x ) and acetylacetonates (M(acac) x ) [123,124], which could be easy to decompose under moderate conditions.
If the metal precursor is composed of two different metal complexes and their decomposition temperatures are quite different, the required alloy structure may not be obtained by direct pyrolysis. For example, Bönnemann and co-workers synthesized a series of Fe-Co nanocrystals by the simultaneous thermal decomposition of Fe(CO) 5 and Co 2 (CO) 8 in tetrahydronaphthalene [125]. Due to the different decomposition temperature between Fe(CO) 5 (200 • C) and Co 2 (CO) 8 (150 • C), their reaction rates were obviously different under the same condition. When the reaction temperature was 180-200 • C, monometallic nanocrystals (Co and Fe) were obtained as a result of the faster decomposition rate of Co 2 (CO) 8 than Fe(CO) 5 . However, Fe-Co alloy could be obtained in the presence of aluminum trialkyl as catalyst at 150 • C. Therefore, when the pyrolysis temperature of the two metal precursors is quite different, it is necessary to introduce the corresponding catalyst to achieve the preparation of bimetallic alloy nanocrystals.
Although the large difference between the pyrolysis temperatures of the two metal complexes is not conducive to the preparation of bimetallic NPs, the existence of this difference also makes it possible to prepare core-shell bimetallic NPs by thermal decomposition method. The core-shell bimetallic NPs can be obtained by a thermal decomposition method. Firstly, the reaction is carried out at the lower decomposition temperature (lower temperature) of the more unstable metal complex to obtain the "core" layer of single metal nanoparticles, while the other more stable metal complex remains unchanged in the reaction system. Then, the reaction temperature is increased or the reaction time is prolonged to make the more stable metal complex decompose. The metal atoms are deposited on the surface of the single metal nanoparticles formed to obtain core-shell bimetallic nanoparticles.

Galvanic Replacement Reaction
As a good way to produce bimetals with special structure, the galvanic replacement reaction is an electrochemical process in which one metal is replaced by another metal ion due to their different reduction potential in the reaction system. In essence, the reaction is also an oxidation-reduction process. Metal (C) with high potential can be easily oxidized. Metal ions (D +x ) with low reduction potential are difficult to reduce by chemical reduction method, but can be reduced by metal C. Therefore, the method is usually suitable for preparing the inactive metal nanocrystals using an active metal as the template. Xia's research group have prepared a lot of bimetals including one active metal and one inactive metal by the galvanic replacement reaction [126,127]. They used Ag as a template, and a salt solution of Au, Pt, and Pd as precursors, to prepare hollow nanoparticles of Au, Pt, and Pd by a galvanic replacement reaction at a certain temperature [126], and the schematic diagram of reaction process are displayed in Figure 11. The nanostructure of Ag used as a template will affect the morphology and wall thickness of Au nanocrystals. The metal with strong reducibility acts as a template to some extent. In addition to Ag, many other metals can also be used as templates, such as Pd [128], Ni [129,130], Co [129,131,132], Pb [129], Cu [133], Se [134] and Te [135]; For example, Mikhlin and co-workers [126] firstly made Pd (a metal with relatively high reducibility) nanoparticles with a specific configuration, and then placed it in a solution of Au 3+ with a higher oxidation potential. Au 3+ will be reduced to zero valence (Au 0 ) and then deposited on the Pd NPs surface, thereby forming Pd-Au nanocrystals with the core-shell structure. Figure 11. Schematic diagram of the experimental procedure that prepared hollow Au nanocrystals by using Ag nanocrystals with various morphologies as templates. Reproduced with permission from [126]. Copyright American Chemical Society, 2002.

Other Methods
Thanks to the nanoengineering technique, the morphology and microstructure of the nanoparticles can be precisely controlled. In addition to the four methods we mentioned above, there are some other synthetic protocols to prepare bimetals with well-defined shapes, such as hard or soft template methods, combustion synthesis, hydrothermal treatment, the combination of the two approaches and so on. These methods have their own advantages and disadvantages in preparing bimetallic nanocrystals with different special structures. The advantages and disadvantages of the four most common methods for preparing bimetallic nanocrystals are shown in Table 3.

Applications of Bimetallic Nanocrystals
Bimetallic nanocrystals have been widely used in many important fields from science to technology [16,17,[136][137][138]. In comparison to single metal nanocrystals, bimetallic nanocrystals possess many unique properties due to the adjustable composition, controllable morphology and variable electronic structure, so they also have many practical and potential applications including catalysis, sensing, biodetection, biomedicine, and so on. For biomedicine, because biological systems are complex, the use of biomaterials are also strict, which requires not only biological activity and biocompatibility, but also requires that the harmful effects after use can be easily eliminated. Considering these factors, single metal nanocrystals usually cannot meet the requirements, while multi-functional bimetallic nanocrystals are more suitable for biomaterial applications. In addition, Pt catalyst has been proved to have excellent catalytic performance for ORR and methanol oxidation reaction (MOR). However, the reserves of Pt and Ir in earth are limited, and the catalytic performance of pure Pt catalyst is not perfect either. Therefore, the introduction of the second metal to form bimetallic nanocrystals is a good solution for improving some important chemical reactions (MOR, ORR and OER). With the development of synthetic bimetallic nanoparticles technology, the micro morphology, carrier properties and composition of bimetallic nanoparticles can be adjusted according to the requirements of different chemical reactions for catalyst activity to obtain the best catalytic activity. In the chemical reactions with important industrial application, a slight improvement in activity, selectivity and stability can bring considerable economic savings. In this section, we have summarized several important applications of bimetallic nanocrystals, such as electrocatalysis, heterogeneous catalysis, sensing and biodetection application, and the composition-dependent and shape-dependent properties of bimetallic nanocrystals in these applications are also discussed.

Catalytic Applications
Bimetallic nanocatalysts have been widely used in solution electrocatalytic reactions, such as methanol electrooxidation, hydrogen electrooxidation, and oxygen reduction reaction and so on. At the same time, they are often used to catalyze heterogeneous reactions, such as CO oxidation, NO x reduction, and petroleum reforming and so on. The applications of bimetallic nanocrystals in heterogeneous catalytic reactions such as anode and cathode of fuel cells are briefly introduced.

1.
Oxygen Reduction Reaction (ORR) The polymer electrolyte membrane fuel cell (PEMFC) is expected to become one of the alternative energy sources for fossil fuels. However, its large-scale application is mainly limited by the kinetics of cathodic reaction, i.e., ORR, including the existence of cathodic overpotential and the loss of catalyst in the process of cathodic reaction [139]. The catalyst should have enough activity to activate O 2 and enough inertia to prevent itself from being oxidized. Compared with Fe, Co, Ni, Ag, Au and other metals, Pt has higher active sites and moderate adsorption and desorption energies for OH, O and other cathode intermediate products, so it is an excellent catalyst for the ORR reaction [140][141][142][143]. Because Pt is a noble metal, and the loss of Pt in the catalytic process is serious, looking for a Pt based alloy with high activity and good stability to replace pure Pt has become a research hotspot in the development of fuel cells. For example, when Pt is alloyed with 3d transition metals, it can not only reduce the cost of catalyst, but change the d-band electronic structure of surface Pt atom by electron transfer and improve the catalytic performance [144].
For the ORR reaction, the catalytic activity of Pt based alloy is not only related to the composition, but also to the exposed crystal surface. The atoms on different crystal planes have different coordination conditions. The difference of coordination number leads to different electronic filling degree of metal d-band, leading to a different adsorption capacity. For instance, Stamenkovic and co-workers investigated the relationship of ORR activity and different Pt 3 Ni single-crystal surfaces by using the ex situ and in situ surface-sensitive probes and DFT calculations, and found that the ORR activity on Pt 3 Ni (111) facet was 10-fold higher than that of Pt (111) facet, and 90-fold higher than that of commercial Pt/C catalyst at that time [139]. The significantly improved performance of the Pt 3 Ni (111) facet was proved to be due to the special electronic structure and weak interaction of Pt atoms on the surface, which increased the number of active sites. After that some PtNi nanostructures were prepared, such as PtNi/Pt-skins [140], Pt 3 Ni octahedral [145], Pt 3 Ni truncated octahedral [146], Pt 3 Ni icosahedra [147], Pt x Ni 1−x octahedral [148], and the Pt 3 Ni nanoframe [149,150]. According to the Nørskov's study [141], the reaction activity of ORR depends largely on the energy change during the formation of hydrogen peroxide and the kinetic process during the formation of water. When the ability of adsorbing O 2 and O is strong, the ability of desorbing OH is weak. The desorption of -OH is the decisive step of ORR. For instance, Xia and co-workers [69] prepared Pd@Pt nL core shell catalysts with different platinum overlayers (n = 0.7-4.3) by using Pd icosahedra as seeds (Figure 12), and specific activities and mass activities of Pd@Pt 2.7L catalyst to ORR were improved by eight and seven times, respectively, in comparison to a commercial catalyst. Moreover, Density functional theory (DFT) calculations demonstrated that the improvement could be ascribed to the weakened binding of hydroxyl to Pt surface growing on Pd (Figure 12g). Chuang [56] prepared PtFe nanocatalysts for electrochemical ORR, and found that ordered fct-PtFe/C catalyst coated with an N-doped carbon exhibited 11-fold mass activity and 10-fold specific activity compared with the commercial Pt/C, and exhibited excellent long-term stability. Pt-based catalysts with nanoframes exhibited excellent ORR activity due to the high atomic efficiency. Luo [151] reported that PtCu concave octopod nanoframes, rhombic dodecahedral (RD) nanoframes, and Pt-Pd-Cu yolk-shell nanoframes (Figure 13a-c) were prepared by altering the type of precursor, halide ion sources and adjusting the reduction order of the precursor. And the octopod nanoframe architectures showed high mass activity of 2.95 A mgPt −1 , which was a 47-fold enhancement in comparison to the commercial TKK-Pt/C catalyst (Figure 13d). The significant improvement can be ascribed to the 3D porous structure, high-index facets, and a large number of active sites exposed on grain boundary edges. As shown in Figure 13e-h, Lee prepared the dendrite-embedded Pt−Ni multiframes by a facile one-pot method, and ORR performance demonstrated that dendrite-embedded Pt−Ni multiframes had high mass activity and catalytic stability, which can be ascribed to the active surface with high-indexed facets, porous hierarchical structure, and the synergy between the inner dendrite core and highly fused multiframes on the surface [152].

Methanol Oxidation Reaction (MOR)
A methanol fuel cell has high energy density and proton exchange membrane has high conductivity. Therefore, methanol fuel cell is considered as a promising cell with potential application, and is increasingly favored by chemical and material researchers. Transition metals, particularly Pt-based metals, are commonly used as catalysts of anode and cathode reactions in fuel cells. At present, the electrocatalytic methanol oxidation (MOR) is often used as a probe reaction to evaluate the comprehensive performance of metal catalysts. CO is the intermediate product of methanol oxidation, which easily causes catalyst poisoning and the loss of catalytic activity. Pt-Ru alloy is proved to be an efficient catalyst for methanol fuel cell because Ru can promote the formation of Ru-OH at lower potential, and Pt can regain the adsorption sites and promote the oxidation process of methanol. According to the Watanabe-Motoo (W-M) mechanism, the OHis adsorbed at the Ru site (Ru-OH), and the intermediate product of CO ads formed at the Pt site. Ru can oxidize the formed CO ads and avoid Pt active site poisoning. However, Tong and co-workers proposed another mechanism by their experimental results [153], in which the MOR occurs at the Pt-Ru boundary site, not a single metal site (Pt or Ru). In addition, the activation region of a PtRu catalyst is usually performed before the MOR [154].
PtPd and PtRu catalysts with different shapes and structure have been proved to be effective catalysts for MOR, because Pd and Ru can change the electronic structure of Pt [15,39,155,156]. In addition, PdPt nanocrystals also exhibited facet and compositiondependent catalytic activity for MOR. For instance, the PtPd nanocubes (exposed (100) facet) exhibited a higher activity than PtPd nanotetrahedrons (exposed (111) facet), whereas the (111) facet exhibited a better durability than (100) [26]. As shown in Figure 14, Yang and co-workers [156] prepared two kinds of Pd@Pt core-shell dendritic nanostructures (hexapod and octapod) by the seeded growth method for MOR. The result showed that hexapods possessed the highest specific and mass activity, and the best catalytic stability compared with octapod and the commercial Pt/C catalyst. In addition, two kinds of Pd@Pt core-shell dendritic nanostructures displayed a significantly improved catalytic performance in comparison to the commercial Pt/C, which was supposed to be due to the dendritic nanostructure and the synergy between Pd and Pt. Our group synthesized PtRh alloy 3D porous nanostructure with tunable atomic ratio (Pt and Rh) by a modified template-free self-assembly approach [157]. Three-dimensional porous nanostructure PtRh with a moderate Rh content (~15 wt%) exhibited high electrochemical activity and good anti poisoning performance for MOR compared with the commercial Pt/C and PtRh NPs. The unalloyed Rh atoms would result in a self-adjusted dissolution capability of PtRh catalysts by the dissolution of Rh atoms. In addition, the formation of Rh oxide in the initial 50 cycles played a significant role in enhancing the electrocatalytic activity for methanol oxidation. On the other hand, the activity of the catalyst depended not only on the exposed crystal surface, but also on the morphology of the particles. Pt-Pd nanodendrites [158], Pt-Pd nanocages [159], and Pt-Pd hollow core-shell structure were reported to be the effective catalysts for MOR. In order to save the usage of noble metals and improve the stability and durability, tertiary metals catalysts were also developed such as PtPdTe nanowires [160], PtPdFe nanowires [161], PtPdNi nanoarchitectures [162], and PtRuM (M = Fe, Ni, Co) [163]. Therefore, the synthesis of tertiary Pt-based nanocrystals should be a promising scheme to design efficient catalysts for MOR.

Oxygen Evolution Reaction (OER)
Energy storage is a particularly important field to improve the utilization of renewable energy because it is difficult to use renewable energy anytime and anywhere [164]. Water decomposition has attracted a large number of researchers' interest [137,165,166], which can convert electrical energy into chemical energy. However, water electrolysis is a demanding reaction due to the large overpotential at the OER [167]. In addition, the activity and stability of some catalysts to OER (Ru x Ir 1−x alloys [167], SrRuO 3 [168]) demonstrated an inverse relationship. Although Ir and Ru were proved to be the best catalysts for ORR, the cost is high due to the fact that they are rare metals. In order to obtain an excellent catalyst, the activity, stability and cost of catalysts should be balanced. Therefore, Ir-based bimetallic nanocatalysts with transition metals (Ti [169], Ni [90,170], Cu [171,172]) will be a good strategy to balance these factors. For examples, Huang et al. [90] constructed monodispersed IrNi x nanocrystals with distinct composition-segregated features (Figure 15a,c) and investigated their structural evolution in various OER environments. They found that Ni of IrNi x nanocrystals could migrate in various OER environments, and an Ir-skin framework was generated in an acidic electrolyte, while a Ni-rich surface layer was observed in an alkaline electrolyte. The Ni migration played a significant role on enhancing the catalytic activity for MOR. Moreover, they synthesized solid Ir-Cu nanocrystals by a facile chemical dealloying strategy and then porous Ir-Cu nanocrystals were obtained through etching with nitric acid. The porous Ir-Cu nanocrystals were highly active and stable toward OER in acidic conditions due to the increased active surface area and plenty of defect. Our group prepared IrNi alloyed nanocrystals by oil phase method for OER. The result showed that IrNi alloyed nanocrystals could enhance OER activity of flower-shaped NiCo 2 O 4 electrode material [173]. IrNi/NiCo 2 O 4 exhibited a relatively lower overpotential and a higher current density, which was ascribed to the synergic effect of the IrNi and NiCo 2 O 4 and high catalytic activity of IrNi alloy.

Heterogeneous Catalysis
Heterogeneous catalytic reactions involve many physical and chemical transformations including the diffusion of reactant molecules in the pore, adsorption on the surface, reaction on the surface of the solid catalyst, desorption and diffusion of product molecules. For the catalyst, the adsorption center is often the catalytic active center. The relation-ship between catalytic performance (i.e., activity, selectivity, and durability) and catalyst properties, composition, size, and shape (more precisely, facet type) of the catalyst has been studied intensively for many years. With the development of synthesis technology of bimetallic NPs, the micro morphology, carrier properties and composition of bimetal can be adjusted as the requirements of different chemical reactions for catalyst activity to obtain the best catalyst. It lies in the subtle change of catalytic activity and selectivity in chemical reactions with important industrial applications. Therefore, as a design platform of high activity catalysts, bimetallic nanoparticles have great potential in the field of catalysis. Recently, a variety of bimetallic catalysts have been designed and applied to different types of chemical reaction, such as CO oxidation [174], hydrogenation/dehydrogenation [175][176][177], coupling reactions [178,179] and H 2 evolution reaction (HER) [180][181][182], and showed superior catalytic activity. The composition, size, and morphology of a bimetallic catalyst has a great effect on its catalytic properties. In order to better understand the relationship between the structure and properties of bimetallic catalysts, two important types of reaction including H 2 evolution reaction and carbon carbon coupling reaction will be discussed in detail.
Catalytic or photocatalytic hydrogen production is an effective means of energy regeneration and storage today. Generally speaking, hydrogen storage materials are mainly small molecules, such as sodium borohydride, hydrazine, lower alcohols and borohydrides, hydrides (LiH, MgH 2 , AlH 3 ) and so on. It has been reported that the common hydrogen production catalysts are Ni-based catalysts (PtNi [181,183], RhNi [182], IrNi [184], PdNi [180,185], FeNi [186] and CoNi [187]), especially Rh-Ni and Pt-Ni alloy catalysts, which have the best activity and selectivity. Moreover, the composition and morphology of the alloy catalyst have a great influence on the performance of the catalyst. For example, Mao and co-workers [180] prepared PdNi hollow alloy with different stoichiometry by a galvanic replacement method for photocatalytic hydrogen evolution, and the order of the hydrogen generation rate is Pd 1 Ni 1 > Pd 2 Ni 1 > Pd 1 Ni 2 > Pd. The enhanced performance can be ascribed to the stronger interaction between Pd 1 Ni 1 hollow NPs and CdS than other alloys. In addition, recently the development of multi-element alloys and non-noble metal alloys have been proven to be a good way to solve the high cost and stability problems of noble metal catalysts [188,189]. Wang and co-workers investigated the catalytic performance of bimetals (PtCo and PtNi) and ternary alloy (PtNiCo) catalysts for hydrogen production, and the result showed that the PtNiCo catalyst exhibited excellent HER performance, superior to PtNi, PtCo and commercial Pt/C catalysts [188].
The carbon-carbon coupling reaction is an important kind of carbon increasing reaction, including Sonogashira-, Ullmann-, Suzuki coupling, etc., which plays a significant role in medicine, biochemistry and other industries. The research demonstrated that Pd based nanoparticles exhibited high catalytic activity for the carbon-carbon coupling reaction, and the component really played the catalytic role was zero valent Pd [190][191][192]. However, these coupling reactions are only carried out on the surface of nanoparticles, and most of the remaining Pd is wasted. Therefore, how to improve the utilization rate of Pd and reduce the amount of Pd used in this process is a challenging problem. The introduction of iron series elements (Fe, Co, Ni) into a Pd system can not only reduce the cost of the catalyst, but change the activity and selectivity of the catalyst by adjusting the electronic structure. The Hyeon group synthesized the Pd-Ni NPs with a Ni-rich core/Pd-rich shell structure by thermal deposition method, and the Pd/Ni NPs displayed higher catalytic activity and better recycling performance than pure Pd NPs. PdCo alloyed NPs displayed high catalytic activity to the Sonogashira coupling reaction, and the addition of Co could not only make the catalyst easier to recycle but be reused several times without significant loss of activity. In addition to increasing the composition, the preparation of PdM bimetal with special structure can also improve the catalytic performance. For example, Xia and coworkers [193] prepared the core-shell-like catalyst Ni-Pd/CB for Suzuki-Miyaura coupling reaction and the catalytic performances was enhanced significantly under mild aerobic conditions without using toxic solvents. In addition, the Ni core not only make the catalyst have magnetically separable ability, but also greatly improves the utility of the Pd element.

Energy Conversion Applications
CO 2 is one of the most widely existing carbon sources in nature, but it is also the lowest energy form of carbon. Absorption and capture of CO 2 and catalytic reduction of CO 2 to high value-added compounds are also the means of conversion and utilization of CO 2 . The most mature industrial application of fixing CO 2 by chemical method is to produce urea, ammonium bicarbonate and other fertilizers. However, the research on conversion of CO 2 to other high value-added carbon containing small molecular compounds, such as hydrogenation to alkanes, olefins and other fuels, or to medium acid, ethanol and other chemical products, has not been extended to large-scale applications. The application of this process mainly depends on the development of high catalytic performance and low-cost catalysts. The preparation of CO, HCOOH, CH 3 OH, CH 4 , C 2 H 6 and other organic hydrocarbon small molecular compounds by the electrochemical catalysis of CO 2 have attracted the attention of researchers as a promising method for large-scale energy storage (power storage) of solar energy and wind energy due to its relatively mild conditions, strong controllability and high yield per unit area (compared with a direct photocatalytic method). At present, the catalytic conversion methods of CO 2 are widely studied, including photocatalytic reduction, chemical catalytic reduction and electrochemical catalytic reduction.
Based on the continuous understanding of the properties of a single metal material, following Kuhl's research idea of adjusting the CO binding energy of alloy materials to improve the catalytic activity and product selectivity, a large number of metal alloy materials have been used to catalyze the reduction of carbon dioxide in the last five years. The combinations of alloy materials mainly include noble metal noble metal, noble metal non noble metal and non-noble metal non-noble metal, which are controlled by material composition. Christopher and co-workers [194] prepared Pd y Au (1-y) alloy (y = 0, 0.25, 0.45, 0.8) thin film and investigated their performance for the electrocatalytic reduction of CO 2 . And the result showed that all AuPd alloys had higher activity and better selectivity for formate than single Au or Pd. The improved performance of AuPd alloy was attributed to yield new electrocatalytic properties due to synergistic effect of gold and palladium.
Compared with the alloy materials with noble metal components, the bimetallic materials formed by two kinds of non-noble metal can also obtain high catalytic activity and selectivity if the size, shapes and compositions could be reasonably designed. For example, Abdesslem [195] reported that CuIn alloy were obtained by reducing CuInO 2 and used to electrocatalytic reduction of CO 2 . The performance results showed that CuIn alloy catalyst had high catalytic activity and selectivity for CO 2 reduction, which was ascribed to the generation of active sites that convert CO 2 to CO. Noble metal Pd is a good catalyst for CO 2 reduction, but it is easily poisoned by CO. The synthesis of Pd-based alloy catalysts is a good solution to overcome the problem. For example, Toshihiro [196] synthesized PdCu bimetallic catalysts and studied the influence of the catalyst composition on the CO 2 reduction activity and the selectivity. The result showed that high Pd/Cu ratio led to production of formate rather than hydrogen, and PdCu exhibited excellent stability for CO 2 reduction with a small overpotential due to the electrical interaction between Pd and Cu [196].

Sensing Applications
A sensor is a detection device, which can selectively recognize the target information and transform the information into electrical signal or other measurable signal according to certain rules. Under normal conditions, bimetallic NPs can be designed and obtained to express their unique properties of each metal. Therefore, a lot of effort has been devoted to preparing and developing bimetallic nanocrystals with well-defined structure (such as facets, atomic order and spatial arrangement). Thanks to the efforts of scientific researchers, many groups have already synthesized a large number of different bimetallic nanocrystals to meet people's different needs. It is a fact that bimetallic nanocrystals have been widely used in many important fields because of their excellent properties, such as catalytic properties, optical properties, localized surface plasmon resonance (LSPR), photocatalytic properties and magnetic properties. etc. More importantly, the modification and doping of bimetallic nanocrystals especially noble metals (Pd, Pt, Au, Rh, and Ag) have been proved to be among the most effective ways to reduce the operating temperature of sensors, enhance the response of target gases and improve the selectivity of sensors.

Metal Oxide Semiconducting (MOS) Sensors
Semiconducting gas sensors are composed of sensors with semiconducting metal oxide materials as the main materials like SnO 2 , ZnO, WO 3 . etc. After nearly 60 years of development, great progress has been made in the mechanism and materials, especially in the response value and selectivity. The modification and doping of bimetals have played a very significant role in improving their gas-sensing properties. For example, due to the complex detection environment, the diversity of gas molecules, and the characteristics of semiconducting gas-sensing materials, it cannot accurately distinguish different gases like acetone, ethanol, formaldehyde that have similar properties in the application, which is an urgent problem to overcome. The stability of semiconducting gas sensor is also a problem. Whether the sensors can detect the target gas stably is related to the production as well as life. However, owing to the development of science and technology, the modification and doping of bimetallic nanocrystals can solve this problem much better than ever before. Because different metals have different properties, we can design and custom-made the bimetallic nanocrystals structure and morphology of materials according to the requirements, so as to better solve the problem of selectivity.
Bimetallic nanocrystals are expected to lower the operating temperature of the sensor and show some new properties. The research work of our group shows that gas sensors with dual selectivity can be obtained by decorating bimetallic nanocrystals on the surface of metal oxide semiconductor. For example, PdAu/SnO 2 composite was prepared by decorating pre-synthesized PdAu nanocrystals on the surface of SnO 2 NSs [197]. The response to acetone and formaldehyde were greatly improved by the decoration of bimetallic nanocrystal PdAu. At the same time, we found that the gas sensing material had double selectivity to different gases at different temperatures. At 250 • C, the response to 50 ppm acetone was 109, and the selectivity and stability to acetone were very good. When the temperature was 110 • C, the response to 50 ppm formaldehyde was 86, showing a good stability and sensitivity. Later, our group prepared bimetallic nanocrystals to detect coal mine gas. As shown in Figure 16a-d, PdPt NPs displayed good dispersion with a narrow size distribution from 2 to 3.5 nm (mean size = 2.7 nm). The sensing performance demonstrated that a PdPt bimetal-functionalized SnO 2 nanosheets sensor could detect carbon monoxide at 100 • C and methane at 320 • C (Figure 16g,h) [198].

Electrochemical Sensors
The mechanism of electrochemical sensors is based on ionic conductivity to the electrode and electrochemically active species, which can be oxidized or reduced on the electrode surface. Due to the economic benefits, simple operation, high selectivity and sensitivity, the research and application fields of electrochemical sensors continue to expand. Research in this field is still focused on new sensing strategies, especially on enhancing specificity, detection limit and response time. Nanomaterials are widely used in electrochemical sensors. One significant point is the research and application of bimetallic nanocrystals, which play a significant role in the development of electrochemical sensors. Due to electronic and synergistic effects, electrochemical sensors based on bimetals usually exhibit higher sensitivity and better selectivity than either of the two metals. For many years, scientists have been committed to the research and development of various electrochemical sensors, among which the electrochemical gas sensors based on bimetals have also been booming. Many electrochemical sensors are called electronic tongues, and research focuses on the development of liquid sensors and chemometric analysis of data.  [198]. Copyright American Chemical Society, 2019.
Owing to their simplicity, low energy consumption and the ease with which they can be miniaturized, electrochemical sensors are very suitable for the development of portable sensing devices. Up to now, bimetallic nanocrystals have been applied and tested for many kinds of substances, such as hydrogen peroxide, uric acid, heavy metal ions, and glucose and so on. Many research groups, including us, have done some meaningful works in this field [199][200][201][202][203]. For example, PtW/MoS 2 composite were prepared by in-situ growing on the surface of as-obtained MoS 2 NSs (Figure 17a,b) [199]. The electrocatalytic measurements showed that PtW/MoS 2 exhibited considerable catalytic performance towards reduction of H 2 O 2 , and the real detection limit was determined as 5 nM (Figure 17c,d). In addition, PtW/MoS 2 also displayed good anti-interference capability (dopamine, paracetamol, NO 3− , K + , hemoglobin). As shown in Figure 17e, the monodisperse AuM (M = Pd, Rh, Pt) alloyed nanoparticles were obtained with narrow size distribution and the sensing performance for H 2 O 2 was investigated [200]. Compared with single metal nanoparticles (Au, Pd, Pt and Rh), the electrocatalytic abilities of AuM (M = Pd, Rh, Pt) bimetals to H 2 O 2 were improved remarkably. In particular, the AuPd nanoparticles displayed an enhanced sensitivity at a relatively low test potential and good anti-interference capability to AA.

Catalytic Combustion Gas Sensor
The catalytic combustion gas sensor is based on the thermal effect principle of catalytic combustion. It is composed of detection elements and compensation elements to form a measurement bridge. Under certain temperature conditions, the combustible gas will burn flameless on the surface of the detection element carrier and under the action of the catalyst, the carrier temperature will rise, and the platinum wire resistance inside it will rise accordingly so that the balance bridge will lose balance, and output an electrical signal proportional to the concentration of combustible gas. Among them, the doping and modification of bimetallic nanocrystals is a good solution to improve the performance of gas sensing materials, which can greatly improve their performance. Li and coworkers [204] prepared PdO/Pt-loaded mesoporous Al 2 O 3 film for application in methane catalytic combustion. The sensing performance exhibited a short response time (<9 s) at the concentration of 10-90% LEL, and a high signal output (4.3 mV) for pre-alarm 10% LEL concentration. More importantly, the power consumption of this sensor was as low as 25 mW, which was much lower than the power of traditional sensors (~120 mW).

Biodetection Applications
Biodetection application of bimetals mainly utilizes some special properties of precious metals such as surface plasmon resonance (SPR) and surface-enhanced Raman scattering (SERS) [205,206]. SPR is an optical phenomenon, which applies to a collective oscillation of free electrons in the conduction band when excited by the incident light. Therefore, the SPR phenomenon can be used to track the interaction between biomolecules in natural state in real time. Plasmonic metals are mainly Au and Ag. In addition, the chemical and physical properties of bimetals are more adjustable than that of a single metal. Biosensor-based bimetallic NPs have potential applications in both research and practical uses due to better sensitivity and selectivity. SERS is a phenomenon in which Raman scattering is enhanced when the target molecules are excited in the proximity or on the surface of roughened metal substrate. In this section, we mainly introduce the state of art of biosensors based the mechanism of SPR and SERS. The SPR biosensor is a new type of biochemical analysis system based on the principle of physical optics. It has been proved that plasmonic nanocrystals are extreme sensitivity toward changes the dielectric properties of solvent, adsorbed species [207,208]. In recent years, thanks to their well-known advantages of high sensitivity and selectivity, easy functioning, high specificity, real-time operation and fast speed, the SPR biosensor has been widely used in various fields, such as clinical diagnosis, qualitative and quantitative testing of genetically modified ingredients, virus identification, environmental microbial testing, drug screening and genetic analysis, etc. [209][210][211]. Local surface plasmon resonance (local SPR, LSPR) is a resonance phenomenon of free electrons in metals, and it occurs in metal nanostructures. The extinction phenomenon in LSPR is caused by the absorption and scattering of light by nanoparticles. LSPR has obvious advantages over traditional SPR biosensors due to the relatively simple optical system and the ability to amplify SPR response signal changes. Therefore, biosensors based on SPR and LSPR have been significantly developed in recent years.
Gold and silver are the typical plasmonic metals. Ag NPs always exhibit a stronger and sharper plasmon resonance than Au NPs. However, pure silver is rarely used in practical applications due to the instability caused by moisture, acids, oxidation, heat, and light. The addition of another metal to the Ag system is a good solution to improve the stability and maintain the excellent SPR performance. Yu et al. [212] specifically combined the gold nanorods with the Fab fragments of IgG molecules to perform biological detection. When the IgG antibody molecules in the solution specifically bind onto the gold nanorods surface, it will cause the red shift of the longitudinal plasmon resonance absorption peak of the gold nanorods. Bimetallic nanocrystals have higher SPR refractive index sensitivity than that of single metal nanocrystals, and more suitable for bio-detection. For example, Ding et al. [213] prepared Ag nanoparticles onto ITO substrate by electrodeposition and then deposited a thin Au shell onto Ag surface by immersing the Ag/ITO in HAuCl 4 solution. Compared with Ag/ITO, the obtained Ag@Au/ITO had high chemical stability and low biological toxicity, and exhibited high SPR refractive index sensitivity. In addition, subsequent antibody detection experiments showed that this modification greatly improved the detection sensitivity. In addition, the shift of SPR absorption peak caused by the structural change of bimetallic nanoparticles under the action of external molecules can also be used for biological detection. Yan etc. prepared Au@Ag bimetallic nanocrystals and used it to detect the storage time of food [214]. The continuous deposition of silver on the surface of gold nanorods will cause the shift of the SPR absorption peak. As shown in Figure 18a-f, at the initial time, the solution of Au nanorods was reddish brown. With the extension of time, silver deposited on the surface of Au nanorods, leading to the solution gradually becoming orange-yellow-green. Therefore, color change can reflect the proliferation of E. coli and the storage time of food. Moreover, Au/Ag bimetallic nanocrystals are usually used as colorimetric probes for detecting cyanide. The colorimetric mechanism is that cyanide could react with Au and Ag to form a metal-cyanide complex in the presence of oxygen (Figure 18g). According to this mechanism, some colorimetric cyanide sensors have been made [215,216]. For example, Zeng and co-workers have synthesized Au@Ag core-shell nanocrystals by using citrate capped Au nanoparticles for the colorimetric cyanide sensing [215]. The results showed that UV-vis spectra of Au@Ag core-shell nanocrystals were very sensitive to the thickness of Ag shell (Figure 18h), and thus significantly sensitive to cyanide. Furthermore, the concurrent induced color changes were obvious and visible to the naked eye.

Biodetection Based on Surface-Enhanced Raman Scattering (SERS)
SERS is a phenomenon in which Raman scattering is enhanced when molecules of interest are excited in the proximity or on the surface of roughened metal substrate. There is no consensus on the nature of enhancement mechanism, and most scholars believe that SERS enhancement is mainly composed of physical enhancement and chemical enhancement, and the former is dominant. Sliver nanocrystals often possess higher SERS enhancement due to the significant plasmonic efficiency, but the stability of Ag NPs is poor [217]. Gold nanocrystals are widely used in biological applications due to their good biocompatibility and high stability [218]. The Au-Ag bimetal has been proved to be better nanostructures than single Au or Ag due to combining the advantage of both metals. Therefore, AuAg NPs are widely used in the identification of tumor cells and normal cells, detection of tumor location and DNA diagnosis. As shown in Figure 19, the process of immunoassay using SERS includes three steps: (i) modifying the substrate for capturing antibody; (ii) SERS probe for specific antigen recognition; (iii) Raman spectrum detection. Grubisha et al. detected prostate antigen (PSA) by using gold nanoparticles as Raman signal amplification carrier, and the detection limit was as low as~1 pg/mL [219]. However, Tian et al. found in the experiment that the highest enhancement ability of Ag@Au bimetallic nanoparticles could reach more than 10 times that of single metal (Ag or Au), which greatly improved the detection sensitivity [220]. Huang et al. also obtained a similar result [221]. They developed a novel SERS immunoassay with high sensitivity and selectivity for detecting cancer marker such as AFP. The Au@Ag core-shell structure could take advantage of the properties of both Au and Ag NPs, and improved the insufficient aspects of sensitivity and stability. In addition, with the increase of the thickness of the Ag shell, the SERS signal was increased regularly, which can be ascribed to the generally accepted assumptions that the larger the size of NPs, the more significant the SERS enhancement effect.

Conclusions and Prospects
In the past decade, great progress has been made in the shape-controlled synthesis, characterization, and applications of bimetallic nanocrystals. Introducing a metal into a noble metal system can not only save an amount of noble metal and reduce the cost of the catalyst, but improve the performance by changing the composition, controlling the atomic arrangement, and adjusting the electronic structure. Bimetallic nanocrystals often exhibit some new properties and capabilities due to the synergistic effect of bimetals, not just the simple addition of the properties associated with two single metals. Therefore, bimetallic nanocrystals have been widely used in some important fields including catalysis, sensing, and energy conversion. This article reviewed the progress in the synthesis strategy, and important applications of bimetallic nanocrystals. Four typical synthesis methods for co-reduction, seeded-growth, thermal decomposition and galvanic replacement were summarized. However, several hundred articles about the synthesis and applications of bimetallic nanocrystals have been published each year. Therefore, it is difficult for us to consider all contributions to this field, and we apologize for neglecting some important contributions.
Although there are many achievements in the controllable synthesis and applications of bimetallic nanocatalysts, further research is needed in the following aspects: precisely controlling the morphology, size and structure of bimetallic nanocrystals, and establishing the theory of nanocrystal nucleation and growth mechanisms. Although many synthetic strategies have been developed and many rich nanostructures have been obtained, traditional synthetic methods are not sufficient to control the surface structure of metal nanocrystals at the atomic level. Although researchers have been able to use some in situ characterization techniques to observe the nucleation process of nanocrystals, the process is extremely fast and complex. Therefore, it is difficult for people to understand this process in depth. In addition, the nucleation method has a great influence on the crystal plane, defects, and growth method. Therefore, there are still huge opportunities and challenges with regard to the formation mechanism of bimetallic nanocrystals.
Developing methods for scaling up production: if nanocrystals are to be used in industry, they must be made in large quantities, so exploring new methods or optimizing existing methods is a good solution to expand production. At present, the experimental devices for synthesizing bimetallic nanocrystals mainly include hydrothermal reactor threenecked flasks, etc. Their capacity generally does not exceed 200 mL. While these methods could successfully produce products at the milligram scale, it is impossible to fully meet industrial-level usage. If the volume of the reactor is simply increased, and the amount of raw materials is also proportionally increased, which will alter the reaction kinetics of the nanocrystals, the shape, structure and size of the products cannot be controlled well. In recent years, some new reaction systems have been developed, such as continuous flow and droplet-based systems, which have improved product control and reproducibility.
Chemical and thermal stability of bimetallic nanocrystals: although many published works in the literature reported that bimetals possess good thermal stability, the original shape could also transfer to another thermodynamically favorable shape or architecture by excessive heating together for a long time. In terms of chemical stability, due to the difference of the redox potential, the more reactive metal in bimetallic nanocrystals tends to leach in some applications such as fuel cells. Therefore, the thermal and chemical stability of bimetallic nanocrystals still need to be further studied in specific applications.
Although there are still some challenges, some promising work has been published in recent years. It was proved that introducing a third metal in the bimetallic system may be a promising strategy for improving the performance of bimetallic nanocrystals due to the possible synergetic effects [222]. For example, by decorating PtCu nanocrystals with Ni, a PtCu@PtCuNi catalyst showed a higher activity and stability for ORR than that of PtCu, and mass and specific activities were obviously improved in comparison to those of commercial Pt/C [223]. The method to improve the properties of bimetals is definitely not limited to the introduction of the third metal, and we should use our imagination to continue exploring this. With the in-depth research on the controlled synthesis chemistry and catalytic chemistry of bimetallic nanocrystals, we believe that we will have the ability to precisely control the composition, morphology and size of nanocatalysts, and achieve low-cost, large-scale synthesis of high-performance bimetallic nanocatalysts.