Plasma for Energy and Catalytic Nanomaterials

This Special Issue "Plasma for Energy and Catalytic Nanomaterials" of Nanomaterials is focused on advancements in synthesis and applications of energy and catalytic nanomaterials by plasma [...].

onset potential of 0.95 V as ORR electrocatalyst and an initial potential of 1.49 V as OER electrocatalyst, both of which are much better than those measured for FeCo@NC without Ar-plasma etching.
Gas plasma has also been proved to be a fast, facile, and green method for introducing groups to nanomaterials. Mi et al. [4] modified boron nitride nanosheets (BNNSs) by atmospheric pressure Ar+H 2 O low-temperature plasma initiated by bipolar nanosecond pulse DBD. The as-obtained plasma-modified BNNSs (P-BNNSs) contained nearly twice the content of surface hydroxyl than BNNSs. Moreover, the coating amount of silane coupling agent (SCA) on the surface of P-BNNSs increased by 45% more than the BNNSs, which enhanced the dehydration condensation reaction of P-BNNSs with SCA. Due to the P-BNNSs, the BN/epoxy resin (EP) insulating nanocomposites performed high thermal conductivity and high breakdown strength. Furthermore, some small molecule gases can be produced to exfoliate bulk particles and synthesize two-dimensional (2D) nanosheets via a plasma process. Zhang et al. [5] have successfully obtained 2D MoS 2 nanosheets and 2D g-C 3 N 4 nanosheets. Using H 2 /Ar plasma, the corresponding NH 3 and H 2 S generated and expanded to the layers of bulk (NH 4 ) 2 MoS 4 , while the bulk g-C 3 N 4 was oxidized into corresponding CO x and NO x and generated 2D g-C 3 N 4 nanosheets via air plasma. The prepared MoS 2 and g-C 3 N 4 nanosheets showed the thickness of 2-3 and 1.2 nm, respectively. They exhibited excellent photocatalytic activity due to the nanosheet structure, larger surface area, more flexible photophysical properties, and longer charge carrier average lifetime. It can be predicted that plasma as the environmentally benign approach provides a general platform for fabricating ultrathin nanosheet materials, which will greatly help the practical application and scientific research of 2D catalytic materials.
Unlike conventional preparation methods, which generally need excess toxic reducing chemical agents, plasma can be used to generate redox species with a green engineering. Fan et al. [6] prepared Ag nanoparticles supported on cotton fabric (Ag/Cotton) with high antibacterial activity against both the Gram-negative bacterium E. coli and the Gram-positive bacterium B. subtilis by a surface plasma at atmospheric pressure for the first time. Ag/Cotton exhibited remarkable unusual physical and chemical properties, and excellent antibacterial performance against a wide scope of pathogens. Xie et al. [7] synthesized aqueous gold nanoparticles (AuNPs) using a HAuCl 4 /sodium citrate solution via alternating the current plasma jet (A-Jet) and the pulse power driven plasma jet (P-Jet), respectively. Due to the high concentration of Cl − and H 2 O 2 in the A-Jet, the AuNP growth rate is more than 40 times faster than that in the P-Jet. Moreover, there is a broad size control range and a narrow AuNP size distribution in the A-Jet.
In DBD plasma, the electrode is crucial to the experimental apparatus as well as the packing materials, reactor, discharge power, etc. Li et al. [8] studied CO 2 decomposition using DBD plasma with different metal foam electrodes, including Al foam, Fe foam, and Ti foam. For example, the Fe foam electrode exhibited more discharge area compared with the Fe rod electrode. The CO 2 conversion using Fe foam electrode reached 44.84% (with a corresponding energy efficiency of 6.86%), which is much better than the 21.15% CO 2 conversion reached using the Fe rod electrode (with a corresponding energy efficiency of 3.92%). Taheraslani et al. [9] investigated the deposits formed by CH 4 +Ar plasma processing in a packed bed reactor with packing materials including γ-alumina, Pd/γ-alumina, BaTiO 3 , silica-SBA-15, MgO/Al 2 O 3 , and α-alumina. Usually, the deposits mainly consist of carbon content (91 at. %) with the H/C molar radio around 1.7. Different from other packing materials, Pd/γ-alumina could restrain carbon-rich agglomerates due to the fast hydrogenation of deposit-precursors. Zhang et al. [10] measured vibrational energy distribution and electron energy distribution by high resolution temporal-spatial spectra emitted from the plasma, studied the characteristic evolution and discharge regimes transition of nanosecond pulsed DBD plasma, and distinguished the three main stages in the discharge, namely the streamer breakdown, the transition from streamer to diffuse regime, and the propagation of surface discharge on the plate electrode surface. It is important to develop plasma sources in material synthesis applications.
In summary, the papers published in this Special Issue include: plasma-assisted synthesized nanomaterials, a plasma-modified interface of nanomaterials, plasma-assisted catalysis, and the mechanism of plasma. Yu and co-workers [11,12] gave the brief overview of the advanced progress of plasma for energy and catalytic nanomaterials. The advanced nanomaterials with superior particle size and good dispersion could be synthesized by plasma-assisted preparation methods, including plasma enhanced atomic layer deposition technology, coaxial pulse arc plasma deposition, plasma sputtering, solution plasma sputtering, etc. Furthermore, gas plasma is employed to provide high energy state gas with free radicals, ions, and electrons, which could endow nanomaterials with surface active groups, heteroatom doping, surface etching, chemical oxidation/reduction, and high dispersed components. In addition, plasma could be directly used in catalytic reactions either with or without catalysts. Up until now, understanding the mechanism of plasma and precisely controlling the process of plasma has been a challenge.