In Response to Michael Wininger’s Commentary: Common Roadblocks for Biomaterials Metrologists

I welcome Wininger's commentary [1], and I would like to take the opportunity to address some of the issues raised.[...].


So Why Did We Select These Parameters?
We were aware that similar topographical studies used S a [5][6][7]; S q [6,7]; and S sk [6,7] to evaluate prostheses for a range of joints. We also found compelling evidence from an industrially focused study [8] to link surfaces with high S sk values to improved distribution of lubricant. We deemed it prudent to include the latter in our analysis, despite the fact that we could not find any bio-medically focused studies that had used it previously. Furthermore, these parameters are considered standard measures for surface topography and are included in ISO 25178-2 [9]. We felt that this further justified our use of S a ; S q ; S sk ; and S ku to evaluate the surfaces in our recent study.

Sample Size
Wininger raised the issue of sample size and makes two inaccurate assertions of our study. First he claims that we only evaluated "a single specimen per phalanx"; and then states "it should be strongly encouraged that studies based on a single specimen be withheld until additional samples can be collected and analyzed". I do not want readers of Wininger's commentary [1] to think that we only evaluated one sample and I urge the readers to refer to our study [2] before forming any biases. We were in fact able to secure two prosthesis pairs for each of the four nominal sizes produced by the manufacturer. For each of the eight prosthesis pairs we took ten topographical measurements from the proximal condyles; and a further ten from the medial plateaux. Figure 1 illustrates the sampling approach used to obtain the 160 measurements.

Roughness Parameters
Wininger has proposed a novel roughness parameter described as the spatial analogue to the jerk, a phenomenon commonly encountered in kinematics. I feel that Wininger's goal to implement such a parameter is admirable, and I fully acknowledge that use of any one of the four previously mentioned parameters used in isolation cannot adequately describe a given surface. In our study we set out to measure these four parameters; we subsequently discussed which are the most appropriate; and which combinations work well together to describe surface phenomena. To paraphrase the findings of our study: we reported no need to measure both Sa and Sq as they are proportional to one another, with the latter returning only slightly higher values in magnitude; we reported that surfaces with a combination of negative Ssk and high Sku values indicate the presence of sharp valleys, which could hold the key to improved lubricant distribution. To summarize our position, we are aware of the limitations of using just one roughness parameter and we are moving towards more rigorous methods of surface characterization.
Wininger illustrated how the jerk parameter can be used to distinguish between two very different surface formations both with the same skewness. In this example one surface was smooth but inclined; the other was a random rearrangement of the heights showing a relatively level but rough surface. This example demonstrates the problems encountered by metrologists when dealing with profiles that are not flat. In our study we used the software MetroPro (Zygo Corporation, Middlefield, CT, USA), which has an in-built feature capable of accounting for spherical or cylindrical profiles. Take for instance a spherical surface that has not yet been corrected (Figure 2A). The high apex and the low slopes are merely read as relative heights and are subsequently used to calculate false roughness parameters. Once the spherical profile has been negated ( Figure 2B) it is possible to quantify the true topography of the surface. Note the difference in the Sa; Sq; Ssk and Sku values presented in Figure 2A,B.
I thank Wininger for acknowledging that we have adhered to established practices. I accept that the standards governing surface roughness measurement may not be perfect, my co-authors and I will consider Wininger's useful comments prior to conducting out next topographical study. I hope that this response sheds more light on the rationale used for selecting the parameters that we did; and provides further explanation of the methods that we used.

Roughness Parameters
Wininger has proposed a novel roughness parameter described as the spatial analogue to the jerk, a phenomenon commonly encountered in kinematics. I feel that Wininger's goal to implement such a parameter is admirable, and I fully acknowledge that use of any one of the four previously mentioned parameters used in isolation cannot adequately describe a given surface. In our study we set out to measure these four parameters; we subsequently discussed which are the most appropriate; and which combinations work well together to describe surface phenomena. To paraphrase the findings of our study: we reported no need to measure both S a and S q as they are proportional to one another, with the latter returning only slightly higher values in magnitude; we reported that surfaces with a combination of negative S sk and high S ku values indicate the presence of sharp valleys, which could hold the key to improved lubricant distribution. To summarize our position, we are aware of the limitations of using just one roughness parameter and we are moving towards more rigorous methods of surface characterization.
Wininger illustrated how the jerk parameter can be used to distinguish between two very different surface formations both with the same skewness. In this example one surface was smooth but inclined; the other was a random rearrangement of the heights showing a relatively level but rough surface. This example demonstrates the problems encountered by metrologists when dealing with profiles that are not flat. In our study we used the software MetroPro (Zygo Corporation, Middlefield, CT, USA), which has an in-built feature capable of accounting for spherical or cylindrical profiles. Take for instance a spherical surface that has not yet been corrected (Figure 2A). The high apex and the low slopes are merely read as relative heights and are subsequently used to calculate false roughness parameters. Once the spherical profile has been negated ( Figure 2B) it is possible to quantify the true topography of the surface. Note the difference in the S a ; S q ; S sk and S ku values presented in Figure 2A,B.
I thank Wininger for acknowledging that we have adhered to established practices. I accept that the standards governing surface roughness measurement may not be perfect, my co-authors and I will consider Wininger's useful comments prior to conducting out next topographical study. I hope that this response sheds more light on the rationale used for selecting the parameters that we did; and provides further explanation of the methods that we used.