Three-Dimensional Performance Analysis of a Radial-Inﬂow Turbine for Ocean Thermal Energy Conversion System

: Turbine is one of the key components of the ocean thermal energy conversion system (OTEC), and its aerodynamic performance and geometric dimension affect the performance of the system directly. This paper proposes a design method for the radial inﬂow turbine suitable for the ocean thermal energy conversion based on the parameter optimization of the ocean thermal energy conversion system. Aiming at the application characteristics of marine thermal energy conversion in a small temperature difference environment and the special thermophysical properties of the organic working ﬂuid in this environment, one-dimensional design and three-dimensional CFD analysis of the turbine is separately done, of which the results were compared. At the same time, the performance of the turbine was veriﬁed by changing the inlet and outlet conditions of the radial turbine under the design conditions. The conclusion is that the three-dimensional CFD results of the turbine are in good agreement with the one-dimensional design, and the internal ﬂow ﬁeld of the turbine is stable, without obvious backﬂow and eddy current, which meets the application requirements of the ocean thermal energy conversion.


Introduction
Thermal energy is a new type of renewable energy that is currently being developed and utilized all over the world. Our country is rich in thermal energy resources. The marine environment of the South China Sea [1] provides excellent conditions for the development of marine thermal energy in this sea area. At the same time, the underwater cold water masses in coastal regions of the Yellow Sea and the East China Sea also make coastal areas of the mainland have the potential to develop ocean thermal energy [2]. Ocean Thermal Energy Conversion [3] (OTEC) refers to the technology that uses the temperature difference between surface warm sea water and deep ocean cold sea water to drive a turbine to drive a generator to generate electricity, whose most basic principle is the Rankine cycle [4,5]; the current most efficient cycle is National Ocean Cycle [6]. The turbine that drives the generator to generate electricity is the most critical equipment for thermoelectric power generation. It is an important component that converts thermal energy to mechanical energy and finally converts into electrical energy, which connects the internal circulation of the system and the external electrical energy output. Its efficiency has a direct impact on the efficiency of the entire system. Radial-inflow turbines have become the first choice for the OTEC systems due to their compact structure, large single-stage enthalpy drop, and high expansion efficiency [7]. The application of radial-inflow turbines in the organic Rankine cycle is very mature, and many scholars at home and abroad have conducted research on it [8][9][10][11][12][13]. However, the environmental characteristics of the OTEC with small Figure 1 shows a schematic diagram of the ocean thermal energy conversion cycle. The liquid working fluid from the condenser is pressurized by the pump, enters the evaporator, absorbs heat from the warm sea water, and becomes saturated or superheated steam. The steam then flows into the turbine, where it is expanded to generate electricity. Finally, the exhaust gas of the turbine is condensed into liquid by the cold sea water through the condenser.
organic Rankine cycle is very mature, and many scholars at home and abroad have conducted research on it [8][9][10][11][12][13]. However, the environmental characteristics of the OTEC with small temperature difference and the thermophysical properties of organic working fluids have higher requirements on the design and performance of turbines, and there is less research.
At present, the United States and Japan are more mature in the design and research of the OTEC turbines. K.G.Nithesh [14][15][16] and others have carried out related research on 2kW ocean thermal energy conversion turbines with R22 as the working fluid, of which the aerodynamic design is finally completed by studying the installation angles of different vanes and the number of blades. South Korea's Do-Yeop Kim [17] adopted RTDM program for aerodynamic design of a 100kW ocean thermal energy conversion radial turbine with a working fluid of R32, and used CFD technology to verify its design; in addition, Do-Yeop Kim [18] also conducted a preliminary and accurate design of highefficiency radial turbines by selecting appropriate flow coefficients and load coefficients for the target efficiency, and average line analysis and three-dimensional viscosity simulation was carried out in order to verify the performance of the proposed method under design and non-design conditions. In the field of domestic ocean thermal energy conversion turbines, Weige Zhao of Tianjin University [19] conducted research and development on 200 W ammonia saturated steam turbines. The ocean thermal energy conversion research group of the First Institute of Oceanography, Ministry of Natural Resources has completed the design, manufacture and research of 15 kW ocean thermal energy generating ammonia turbine and 10 kW ocean thermal energy dual-head turbine [20].
This article first calculated the parameters of the organic Rankine cycle for ocean thermal energy conversion to achieve the best design conditions for the turbine, then conducted one-dimensional design and detailed three-dimensional CFD analysis of the radial inflow turbine, and compared the results of one-dimensional design and three-dimensional CFD simulation. At the same time, the performance of the turbine is verified by changing the inlet and outlet conditions of the radial turbine under design conditions. Figure 1 shows a schematic diagram of the ocean thermal energy conversion cycle. The liquid working fluid from the condenser is pressurized by the pump, enters the evaporator, absorbs heat from the warm sea water, and becomes saturated or superheated steam. The steam then flows into the turbine, where it is expanded to generate electricity. Finally, the exhaust gas of the turbine is condensed into liquid by the cold sea water through the condenser.  Table 1 for details).  Table 1 for details).

Parameter Optimization of the Organic Rankine Cycle
where m is mass flow rate, kg/s, h is enthalpy, kJ/kg, c is specific heat capacity, kJ/(kg·K), T is temperature, K. Subscript 1 to 4 are state points, Subscript w is warm sea water and c is cold sea water. Subscript i and o are inlet and outlet. The thermodynamic process of the working fluid in the turbine is an isentropic expansion process [22], and its output power is The thermodynamic process of the working fluid in the pump is an adiabatic compression process, and the power consumption of the pump is The net power output of the ocean thermal energy conversion system is calculated as follows: The theoretical efficiency of the cycle is From May to October, the surface water temperature of the South China Sea can be maintained above 28 • C for a total of 6 months. Therefore, this paper selects 28 • C as the heat source temperature. The temperature of deep cold sea water is generally stable, and the cold source temperature is set at 4 • C.
Studies have shown [23] that the temperature difference between the inlet and outlet of seawater in the heat exchanger is about 2~4 • C. When the temperature difference of seawater in the heat exchanger becomes smaller, it has a huge impact on the power consumption of the pump. When the temperature change of warm sea water and cold sea water in the heat exchanger is greater than 2 • C, the power consumption of the warm sea water and cold sea water pump will be maintained at a low level, so the temperature drop of the warm sea water and the temperature rise of the cold sea water are 2 • C. According to the reference [24][25][26], the pitch point temperature of the evaporator and condenser is 2 • C.
The choice of circulating working fluid should not only consider its theoretical thermodynamic properties, but also fully consider safety and environmental friendliness. In this study, the refrigerant R134a was selected as the working fluid of the turbine [27] based on the research of Sauret and Rowlands, which evaluated five different fluids based on the QGECE (Queensland Geothermal Energy Center of Excellence) thermodynamic model. Results showed that the highest performance cycle based on R134a generates 33% higher net power than the lowest performance cycle based on n-pentane [28][29][30][31]. In addition, R134a has relatively low critical pressure and temperature, low flammability, low toxicity and relative inertness. Also, impact on the environment is relatively small; namely, low global warming potential (global warming potential) and low ozone depletion potential (ozone depletion potential).
According to the international authoritative working fluid physical property database (NIST REFPROP V9.1) [32] developed by the National Institute of Standards and Technology (NIST), the physical property parameters of each state point are calculated, as shown in Table 1. The design conditions of the turbine can also be obtained in Table 2.

One-Dimensional Design of Radial-Inflow Turbine for ORC
Aiming at the application characteristics of marine thermal energy conversion in a small temperature difference environment and the special thermophysical properties of the organic working fluid in this environment, the aerodynamic design and optimization of this turbine are carried out combined with the design ideas of ORC radial turbine [33,34]. The overall working process of the centripetal turbine is shown in Figure 2. Firstly, working gas flows into the volute at a certain speed which is evenly distributed to the nozzle vanes; then, the gas enters the nozzle to expand, making part of the internal energy convert into kinetic energy (0-1), of which the pressure decreases, the temperature decreases and the speed rises. Next, the gas accelerated by the nozzle enters the rotor at high speed to push the rotor to rotate, driving the motor to generate electricity, while the gas continues to expand in the rotor, completing the internal energy to mechanical energy transition (1)(2). Finally, the working fluid flows out of the turbine to the pipeline after passing through the diffuser.

Initial Parameter Optimization
The preliminary design of the centripetal turbine takes 50% of the engineering time, which is due to too many empirical parameters being used in the preliminary design of the turbine [35]. The first step of one-dimensional design is to determine the basic parameters, because the use of different basic parameters will lead to a large number of design solutions with different geometric dimensions and losses. According to the energy equation and the velocity triangle, the wheel efficiency of the radial turbine is given by Equation (7):

Initial Parameter Optimization
The preliminary design of the centripetal turbine takes 50% of the engineering time, which is due to too many empirical parameters being used in the preliminary design of the turbine [35]. The first step of one-dimensional design is to determine the basic parameters, because the use of different basic parameters will lead to a large number of design solutions with different geometric dimensions and losses. According to the energy equation and the velocity triangle, the wheel efficiency of the radial turbine is given by Equation (7): Turbine circumference efficiency is determined by 7 basic parameters; namely, reaction degree Ω, wheel diameter ratio , speed ratio and nozzle speed coefficient φ, rotor speed coefficient ψ, rotor inlet absolute airflow angle α1 and outlet relative flow angle β2.
These seven basic parameters are first selected by the method of genetic algorithm optimization with the goal of maximizing wheel efficiency [36]. At the same time, they are corrected to meet the corresponding flow channel requirements during the calculation process. The final values and empirical ranges of the 7 basic parameters [37] are shown in Table 3.  Turbine circumference efficiency is determined by 7 basic parameters; namely, reaction degree Ω, wheel diameter ratio D 2 , speed ratio u 1 and nozzle speed coefficient ϕ, rotor speed coefficient ψ, rotor inlet absolute airflow angle α 1 and outlet relative flow angle β 2.
These seven basic parameters are first selected by the method of genetic algorithm optimization with the goal of maximizing wheel efficiency [36]. At the same time, they are corrected to meet the corresponding flow channel requirements during the calculation process. The final values and empirical ranges of the 7 basic parameters [37] are shown in Table 3.

Mathematical Model
In the process of one-dimensional initial design and thermal calculation of the turbine, the internal flow can usually be regarded as a steady-state flow that ignores the temperature change of specific heat and isentropic exponent, adiabatic and inviscid [38]. The gas first expands and accelerates in the nozzle, which increases the gas velocity at the nozzle outlet to C 1 . Then, the gas rotates into the rotor at a high relative speed of ω 1 . The circumferential velocity of the blade is u 1 , and the gas continues to expand in the blade. The relative velocity of the airflow in the outlet is called ω 2 , and its absolute velocity C 2 is the vector sum of the velocities u 2 and ω 2 at this point.
The rotor inlet circumferential velocity, absolute velocity, relative velocity and relative flow angle are given by: where C S is the ideal velocity of the flow at rotor outlet and isentropic ideal enthalpy drop h s has the form The relative velocity, absolute velocity, peripheral velocity and relative flow angle at the rotor outlet are calculated as: The gas flow conditions in the inlet and exhaust of the rotor are represented by velocity triangles at the inlet and outlet of the rotor, as shown in Figure 3.
The relative velocity of the airflow in the outlet is called ω , and its absolute velocity is the vector sum of the velocities and ω at this point. The rotor inlet circumferential velocity, absolute velocity, relative velocity and relative flow angle are given by: where is the ideal velocity of the flow at rotor outlet and isentropic ideal enthalpy drop ℎ has the form The relative velocity, absolute velocity, peripheral velocity and relative flow angle at the rotor outlet are calculated as: = ω sin The gas flow conditions in the inlet and exhaust of the rotor are represented by velocity triangles at the inlet and outlet of the rotor, as shown in Figure 3.  The thermal parameters of the internal runner part of the turbine are calculated accordingly based on the determination of the basic parameters, and the main design dimensions and structure of the runner including the volute, the nozzle and the rotor are obtained. The rotor inlet diameter is given by: where l 1 and τ 1 are respectively the rotor blade height and the rotor blockage factor at the inlet, l 1 D 1 is specified as 0.04 by experience. The nozzle outlet diameter is calculated as: where ∆ 1 is the length of the interspace between the nozzle and rotor, set as 1 mm. The nozzle blade height is given by: where τ N is the nozzle outlet blockage factor. The rotor blade height at the inlet has the form In Equations (23) and (24), D 2 and D 2 denote the shroud diameter and hub diameter at the rotor outlet, respectively.
where A 2 is the rotor outlet area and D 2m is the average diameter of the rotor outlet, defined as The rotor blade height at the outlet has the form Considerable spread angle of working wheel midday [39] The rotational speed is given by Radial turbine isentropic expansion efficiency Among them, h is the actual enthalpy drop of the turbine, i 0 is the enthalpy value of the turbine inlet, respectively, i 4 and i 2s are the actual enthalpy value and isentropic enthalpy value of the diffuser outlet, respectively.
In the process of gas expansion, certain losses will inevitably occur. In order to improve design accuracy, it is necessary to consider the energy loss q N in the nozzle, the energy loss q r in the rotor, the energy loss q k of the diffuser in the turbine calculation unit wheel back friction loss q B and internal leakage loss q l .
where ξ f is the friction coefficient of the rotor When δ l m ≤ 0.05, When δ l m > 0.05 δ l m is the relative axial clearance of the working wheel The flow channel efficiency of a radial turbine can be calculated by Formula (39).
Here, ξ i = q i h s , i is a different subscript code.

Design Results and Verification
The main aerodynamic design parameters of the radial inflow turbine can be obtained, according to the above-mentioned initial design parameters and one-dimensional model, as shown in Table 4. The Enthalpy-entropy change of the working fluid in the calculation process is shown in Figure 4, which details the change of the thermodynamic parameters of the entire expansion process. The actual fluid properties refer to NISTREFPROP 9.1.    In order to ensure the accuracy of the one-dimensional calculation, the design results are verified based on the data provided by the references. The comparison between the results of this study and the references is shown in Table 5. It can be seen that the design results of this study are all within the range given in the references, and are in good agreement with them.

Three-Dimensional Numerical Simulations of the Radial-Inflow Turbine for OTEC
In order to compare between the one-dimensional calculation results and the CFD results, ANSYS-CFX was selected to perform steady-state 3D viscous flow simulation. As a professional software (ANSYS 2019 R1, 31/12/2020) for turbomachinery simulation, this commercial software (ANSYS 2019 R1, 31/12/2020) has certain reliability. For the sake of robustness and the experience gained from previous CFD work, the first-order upwind convection scheme is used to realize the discretization of the Reynolds averaged Navier-Stokes (RANS) equation, and the k-ε-turbulence model with a scalable wall function is selected, which is simple, stable, saves computing resources, and is widely used in the fields of aviation and turbomachinery [43,44]. In addition, it is solved by general equations (energy, momentum, mass) provided by ANSYS-CFX.

Theoretical Model
(1) Reynolds Averaged Navier-Stokes (RANS) Equations As described above, turbulence models seek to solve a modified set of transport equations by introducing averaged and fluctuating components. For example, a velocity U i may be divided into an average component, U i , and a time varying component,u i .
Substituting the averaged quantities into the original transport equations results in the Reynolds averaged equations given below.

∂ρ ∂t
The Reynolds averaged energy equation is: The mean Total Enthalpy is given by: Similarly, the Additional Variable φ may be divided into an average component, φ, and a time varying component, ϕ. After dropping the bar for averaged quantities, except for products of fluctuating quantities, the Additional Variable equation becomes ∂ρφ ∂t where ∆t is a time scale that is large in relation to the turbulent fluctuations, but small in relation to the time scale to which the equations are solved; τ is the molecular stress tensor (including both normal and shear components of the stress); the ρu i u j , ρu j h and ρu i ϕ are the Reynolds flux terms; the ∂ ∂x j U i τ ij − ρu i u j term in the equation is the viscous work term; S M and S E are momentum source and energy source; Γ is diffusivity (2) The k-Epsilon Model k is the turbulence kinetic energy and is defined as the variance of the fluctuations in velocity. It has dimensions of (L 2 T −2 ); for example, m 2 /s 2 . ε is the turbulence eddy dissipation (the rate at which the velocity fluctuations dissipate), and has dimensions of per unit time (L 2 T −3 ); for example, m 2 /s 3 .
The k-ε model introduces two new variables into the system of equations. The continuity equation is then: ∂ρ ∂t And the momentum equation becomes: The values of k and ε come directly from the differential transport equations for the turbulence kinetic energy and turbulence dissipation rate: where S M is the sum of body forces, µ e f f is the effective viscosity accounting for turbulence, C µ = 0.09, C ε1 = 1.14, C ε2 = 1.92, σ k = 1.0 and σ ε = 1.3 are constants, P kb and P εb represent the influence of the buoyancy forces.

3D Modeling and Meshing
The geometry of the turbine is exported to ANSYS-BladeGen to generate the nozzle and rotor channels. Ansys-TurboGrid is used to generate O-H three-dimensional computational grids, as shown in Figures 5 and 6, where the "automatic topology and meshing (ATM optimization)" option is used in the stator and rotor flow channels. It can generate high-quality grids and avoid negative volumes, which is a problem for traditional grid generation [45]. The volute is divided into a tetrahedral mesh, and the volute tongue is locally encrypted. The overall mesh after importing into CFX is shown in Figure 7. This initial mesh was found good enough to run pioneering simulations of the 3D candidate R134a radial-inflow turbine in high flow conditions and establish the complete methodology (thermodynamic cycle, meanline analysis and preliminary viscous CFD simulations). 4059 kPa are, respectively, the critical temperature and pressure of R134a, is the molar volume and is the universal gas constant. To complete the description of the real gas properties, the CFD solver calculates the enthalpy and the entropy using relationships which are detailed in [48]. These relationships depend on the zero pressure ideal gas specific heat capacity c and the derivatives of the Peng-Robinson EoS. c is obtained by a fourth-order polynomial whose coefficients are defined by Poling et al. [49].

Boundary Condition Setting and Simulation Monitoring
The initial simulation and optimization process uses pressure inlet and mass flow outlet as the inlet and outlet conditions, and monitors the outlet pressure and isentropic expansion efficiency. When verifying the optimization results, the pressure inlet and pres-

Boundary Condition Setting and Simulation Monitoring
The initial simulation and optimization process uses pressure inlet and mass flow outlet as the inlet and outlet conditions, and monitors the outlet pressure and isentropic expansion efficiency. When verifying the optimization results, the pressure inlet and pressure outlet boundary conditions are used and the inlet and outlet mass flow and isentropic expansion efficiency are monitored. The specific boundary conditions are listed below: 1. The rated speed of the rotor is defined from the preliminary design and set to 7993 The properties of the refrigerant R134a in the radial-inflow turbine is described by the equation of state (EoS) of Peng-Robinson which is same to the equation of Sauret and Gu [46]. Peng-Robinson EoS provided by ANSYS-CFX is not also simplicity, but also accuracy of this model to perform preliminary real gas compuational simulations. And the EoS also has reasonable accuracy, especially near the critical point [47]. The equations are given as: where ω = 0.326 is the acentric factor of refrigerant R134a, T c = 374.26 K and p c = 4059 kPa are, respectively, the critical temperature and pressure of R134a, V m is the molar volume and R is the universal gas constant.
To complete the description of the real gas properties, the CFD solver calculates the enthalpy and the entropy using relationships which are detailed in [48]. These relationships depend on the zero pressure ideal gas specific heat capacity c p 0 and the derivatives of the Peng-Robinson EoS. c p 0 is obtained by a fourth-order polynomial whose coefficients are defined by Poling et al. [49].

Boundary Condition Setting and Simulation Monitoring
The initial simulation and optimization process uses pressure inlet and mass flow outlet as the inlet and outlet conditions, and monitors the outlet pressure and isentropic expansion efficiency. When verifying the optimization results, the pressure inlet and pressure outlet boundary conditions are used and the inlet and outlet mass flow and isentropic expansion efficiency are monitored. The specific boundary conditions are listed below: 1. The rated speed of the rotor is defined from the preliminary design and set to 7993 rpm (Table 4).
2. The inlet of the volute is set as the pressure inlet, total pressure (0.64 MPa) and total temperature (297.15 K); the diffuser outlet is set as the mass flow outlet, and the mass flow (3.82 kg/s) is calculated from the cycle ( Table 2).
3. There are two interfaces between the outlet of the stator and the inlet of the rotor and between the outlet of the rotor and the inlet of the diffuser, both of which are dynamic connections, defined as the Frozen-rotor model; The volute outlet to the stator inlet is static connection, defined as Stage-Frame Change/Mixing and Automatic Pitch Change model. Figure 8 shows the pressure distribution of the radial turbine for different blade heights. The pressure decreases from the inlet to the outlet of the turbine. For each blade height, the pressure distribution of the nozzle channel is very uniform, and the pressure changes are mainly concentrated in the outlet part where the isobars are dense. The pressure surface and the suction surface are basically symmetrical, and there is no pressure sudden change and reverse pressure gradient. For the rotor channel, the isobars at the front are dense and the pressure gradient is large. Most of the pressure drop is caused by the expansion of the working fluid. On the whole, the pressure changes are relatively uniform and the pressure gradient is relatively slow. On the pressure surface side, the pressure changes slowly and the high pressure area is larger due to the gas impact. It can be seen from the figure that the suction surface pressure is lower than the pressure surface at the same position. In fact, this corresponds to the working principle of the rotor. The gas expanding in the nozzle and entering the rotor will push the rotor to do work, while the gas continues to expand in the rotor, further increasing the driving force on the rotor. The acting surfaces of these forces are pressure surfaces, so the pressure of the pressure surface is higher than the suction surface.

Results
heights. The pressure decreases from the inlet to the outlet of the turbine. For each blade height, the pressure distribution of the nozzle channel is very uniform, and the pressure changes are mainly concentrated in the outlet part where the isobars are dense. The pressure surface and the suction surface are basically symmetrical, and there is no pressure sudden change and reverse pressure gradient. For the rotor channel, the isobars at the front are dense and the pressure gradient is large. Most of the pressure drop is caused by the expansion of the working fluid. On the whole, the pressure changes are relatively uniform and the pressure gradient is relatively slow. On the pressure surface side, the pressure changes slowly and the high pressure area is larger due to the gas impact. It can be seen from the figure that the suction surface pressure is lower than the pressure surface at the same position. In fact, this corresponds to the working principle of the rotor. The gas expanding in the nozzle and entering the rotor will push the rotor to do work, while the gas continues to expand in the rotor, further increasing the driving force on the rotor. The acting surfaces of these forces are pressure surfaces, so the pressure of the pressure surface is higher than the suction surface. Figures 9 and 10 are the overall turbine streamline diagram and the streamline distribution at 50% leaf height, respectively. In order to better show the streamlines, the diffuser in Figure 9 is not shown. It can be seen from Figure 9 that the flow of the turbine from the volute to the stationary blade and then to the moving blade is good, and the streamline is relatively smooth and uniform along the direction of the flow channel, without obvious shock waves and reverse flow. Figure 10 shows the development of streamlines in the nozzle and the rotor. The velocity changes in the nozzle are mainly concentrated in the outlet section where the gas velocity reaches the maximum, and there is a uniform transition from the nozzle outlet to the rotor inlet without obvious shock waves. The distribution of streamlines in the rotor is relatively uniform, with only a slight speed jump on the suction surface, which is completely consistent with the pressure distribution law in Figure 8, and will not cause too much flow loss. Figures 9 and 10 are the overall turbine streamline diagram and the streamline distribution at 50% leaf height, respectively. In order to better show the streamlines, the diffuser in Figure 9 is not shown. It can be seen from Figure 9 that the flow of the turbine from the volute to the stationary blade and then to the moving blade is good, and the streamline is relatively smooth and uniform along the direction of the flow channel, without obvious shock waves and reverse flow. Figure 10 shows the development of streamlines in the nozzle and the rotor. The velocity changes in the nozzle are mainly concentrated in the outlet section where the gas velocity reaches the maximum, and there is a uniform transition from the nozzle outlet to the rotor inlet without obvious shock waves. The distribution of streamlines in the rotor is relatively uniform, with only a slight speed jump on the suction surface, which is completely consistent with the pressure distribution law in Figure 8, and will not cause too much flow loss.     Table 6 shows the comparison between numerical simulation results and aerodynamic design values under design conditions. It can be seen from Table 6 that the relative error of turbine nozzle outlet velocity, turbine outlet pressure, reaction degree, power and isentropic efficiency are all within a reasonable range (<5%), indicating that the simulation results are basically consistent with the one-dimensional design.
The nozzle outlet velocity and reaction degree represent the expansion state of the working fluid in the nozzle and the rotor, respectively. The higher the coincidence with the one-dimensional design value, the closer the working fluid in the nozzle and the rotor is to the ideal state, and the better the performance of the turbine. The outlet pressure is determined by the condenser in the cycle, which is an important evaluation factor in the turbine design process. The difference between the simulation value and the design value is small, indicating that the gas state at the outlet of the turbine outlet is close to the inlet of the condenser, which can avoid unnecessary pressure loss and ensure that the turbine can obtain the highest efficiency. Efficiency is an important indicator for evaluating the performance of a turbine and the output power determines the overall cycle output directly. In this simulation result, both of these two indicators exceed the design value, indicating that the overall performance of the turbine meets the design requirements, can obtain better energy output, and improve energy utilization.  Table 6 shows the comparison between numerical simulation results and aerodynamic design values under design conditions. It can be seen from Table 6 that the relative error of turbine nozzle outlet velocity, turbine outlet pressure, reaction degree, power and isentropic efficiency are all within a reasonable range (<5%), indicating that the simulation results are basically consistent with the one-dimensional design. The nozzle outlet velocity and reaction degree represent the expansion state of the working fluid in the nozzle and the rotor, respectively. The higher the coincidence with the one-dimensional design value, the closer the working fluid in the nozzle and the rotor is to the ideal state, and the better the performance of the turbine. The outlet pressure is determined by the condenser in the cycle, which is an important evaluation factor in the turbine design process. The difference between the simulation value and the design value is small, indicating that the gas state at the outlet of the turbine outlet is close to the inlet of the condenser, which can avoid unnecessary pressure loss and ensure that the turbine can obtain the highest efficiency. Efficiency is an important indicator for evaluating the performance of a turbine and the output power determines the overall cycle output directly. In this simulation result, both of these two indicators exceed the design value, indicating that the overall performance of the turbine meets the design requirements, can obtain better energy output, and improve energy utilization.

Discussion
For further verification and analysis, the turbine outlet boundary is changed to the pressure outlet condition on the basis of the simulation in Section 2.3, keeping other conditions unchanged, and the inlet and outlet mass flow and efficiency are monitored for simulation. The results are shown in Table 7. Mass flow is an important indicator for evaluating turbine design under the conditions of pressure inlet and pressure outlet, which given in the calculation of the entire ocean thermal energy conversion power generation cycle. The small difference between the simulation value and the design value indicates that the turbine has a high matching with the overall cycle, and the actual working process will be closer to the design conditions, which can ensure the highest efficiency under standard conditions. From the results given in Table 7, it can be seen that the mass flow rate of 3.79 kg/s has little difference from the design value, under the conditions of pressure inlet and pressure outlet.
In Table 7, "Pressure Inlet and Mass Flow Outlet" and "Pressure Inlet and Pressure Outlet" are two different inlet and outlet boundary conditions. "Pressure Inlet and Mass Flow Outlet" are pressure inlet (0.64 MPa) and mass flow outlet (3.83 kg/s); "Pressure Inlet and Pressure Outlet" are pressure inlet (0.64 MPa) and pressure outlet (0.3876 MPa). The performance of the turbine designed in this paper is verified by comparing the simulation results and design results under two different boundary conditions. At the same time, the two sets of simulation results can also be compared. The results show that the difference between simulation results and design results is very small, indicating that the performance of the turbine meets the design requirements. At the same time, the output power and efficiency in two sets of simulation are both higher than the design values, which are in good agreement with each other results, which can prove that the performance of this turbine under standard operating conditions can meet the design requirements.

Conclusions
This paper further completes the design process of the radial inflow turbine for ocean thermal energy conversion. The one-dimensional design and three-dimensional CFD analysis of the radial inflow turbine were carried out on the basis of parameter optimization of the ocean thermal energy conversion system. Under design conditions, the performance of the turbine is verified by changing the inlet and outlet conditions of the radial turbine. The main conclusions are summarized as follows.
(1) Three-dimensional CFD analysis shows that the turbine pressure distribution and streamline distribution are uniform without obvious backflow and vortex, at the same time, the nozzle and rotor are well coupled and the internal flow field is stable in the designed OTEC radial inflow turbine.
(2) The three-dimensional CFD simulation results are in good agreement with the one-dimensional design results, indicating that the design model proposed in this paper is reliable.
(3) Under different import and export conditions, the radial inflow turbine can achieve better power output and higher efficiency, indicating that the performance of this turbine under given standard conditions meets the application requirements of ocean thermal energy conversion.
Author Contributions: Conceptualization, methodology, software, validation, data curation and writing-original draft preparation, Y.C.; writing-review and editing, Y.L. and X.Y.; conceptualization, supervision and funding acquisition Y.L.; project administration, L.Z. All authors contributed to the design of the study. All authors discussed, read, edited and approved the article. All authors have read and agreed to the published version of the manuscript.