Control Parameters Optimization of Accumulator in Hydraulic Power Take-Off System for Eccentric Rotating Wave Energy Converter

: To improve the efﬁciency and stability of an eccentric rotating wave energy converter (ERWEC), the adaptive hydraulic power-take-off (PTO) system with an accumulator is designed and developed. Experiments are performed to analyze the effects of trigger pressure, delay time


Introduction
The development and utilization of clean and renewable energy provide a golden opportunity to reduce fossil energy consumption, and it is a key way to meet the requirement of the Paris Agreement on reducing greenhouse gas emissions [1].Wave energy is a kind of clean and renewable energy with abundant reserves, which has attracted the attention of scientists all over the world.Various wave energy converters (WECs) have been designed according to the energy capture methods with different principles, such as oscillating water columns (OWCs), wave-activated bodies, and overtopping devices.An ERWEC can be categorized as a wave-activated body type WEC, which has the capacity to absorb wave energy from all directions.The motion part of the ERWEC device is protected within the closed hull to avoid direct contact with the corrosive seawater, resulting in better survivability and lower maintenance costs.
To date, several ERWEC devices have been studied.In [2], the technical and economical development over three generations of SEAREV WECs have been reviewed.The authors pointed out that the high levelized cost of energy was still the main reason preventing the devices from accessing a grid-connected utility electricity market.PeWEC was designed at Politecnico di Torino, which was a vertical pendulum-based floating WEC absorbing the wave energy from a uni-direction.The experimental tank testing and numerical modeling of a 1:12 scale PeWEC were described in [3].The results showed that the numerical model could be used for the design of the full-scale WEC device and optimization of the parameters of the system.Another typical example of the horizontal eccentric rotor device was the Penguin WEC developed by the Wello Oy company [4].The full-scale prototype has been tested in a real sea state, and the results showed the superiority of harnessing energy from all directions.The above are relatively mature ERWEC devices, and relevant theoretical research can be found in [5][6][7][8].
The WEC devices mentioned above are based on the direct mechanical drive PTO system, which has a relatively short lifetime, high maintenance cost, and poor output power stability [9].The direct linear drive system is an available energy conversion system, which has the ability to swap from motor to generator model at any given moment to provide reactive power for some control strategies [10].The hydraulic PTO is a mature energy conversion system, which is suited to absorbing energy under the condition of large load and slow speed, with the characteristics of effective shock absorption and easy energy storage.A large number of WEC proposals have incorporated hydraulic PTO systems in their designs, such as Pelamis WEC [11].In [12], a critical comparison of load control algorithms for hydraulic system generator power converters was investigated and the proposed torque control algorithm proved to be suitable for hydraulic PTO.Liu et al. [13] developed a latching control strategy for a raft-type WEC with a hydraulic PTO.To the best of our knowledge, such an application in an ERWEC device has not been performed.Meanwhile, the parameters of the PTO system are difficult to determine due to the complexity and coupling effect.An optimization process is necessary to obtain a reasonable PTO structure and optimal conversion efficiency.Aiming at the parameter optimization problem, some researchers have tried to improve the PTO system with advanced optimization algorithms.In [14], to find the optimal PTO system parameters, several approaches are incorporated to solve the nonlinear optimization problem.Yu et al. [15] developed a hydraulic PTO model to trade off mean captured power and power fluctuation using three different power smoothing methods.Neshat et al. [16] proposed a hybrid cooperative co-evolution algorithm framework, which consisted of a symmetric local search plus Nelder-Mead and a cooperative co-evolution algorithm with a backtracking strategy for optimizing relative positions of buoys and PTO parameters for each buoy.Compared with other popular evolutionary algorithms, it showed that the above algorithm framework had better performance in both runtime and solving quality.Sheng et al. [17] proposed a simple and fast-turnaround assessment method to optimize the linear PTO damping coefficient.This method was suitable in the early design stage of the WEC devices and had a similar effect with nonlinear PTO in optimizing the wave energy capture ability.
The accumulator is the critical part of the hydraulic PTO system, which affects the output power efficiency and stability.The hydraulic PTO, including a high-pressure hydraulic circuit and a gas accumulator, has been modeled in [18], which laid a theoretical foundation for the design of a hydraulic PTO system with an accumulator.In the work of [19], the influence of accumulator parameters, such as initial volume and pre-charge pressure, on the power conversion ability of the two-raft-type WEC has been analyzed and discussed.Hansen et al. [20] have analyzed the influence of multiple accumulators on output energy.However, the influence of control parameters, such as trigger pressure and working duration of the accumulator, on the power conversion performance has not been fully studied.It has the potential to improve power generation and reduce costs significantly, combined with parameter optimization and advanced control strategies [21,22].
In this research, a novel application scheme of the hydraulic PTO system for ERWEC devices is proposed.The influence of accumulator control parameters on power conversion performance is analyzed experimentally, and the optimal parameter tuning method is proposed.This paper is structured as follows.In Section 2, the novel hydraulic PTO system of the ERWEC is introduced in detail.In Section 3, the experimental procedure is described, and the results are discussed.In Section 4, the multi-objective optimization techniques used to determine optimal control parameters are proposed.In Section 5, the main conclusions are summarized and suggestions for future research are made.

Mechanical Structure of ERWEC
The schematic representation of the ERWEC is shown in Figure 1a.The motion of the bottom case activated by wave excitation makes the eccentric rotor no longer located at the position with the lowest gravitational potential energy.With the help of gravity, the eccentric rotor will tend to move to the position with the lowest gravitational potential energy.The rotational motion of eccentric rotor around vertical axis could be used to generate electric energy.The 3D schematic diagram of the device designed according to the principle of ERWEC is shown in Figure 1b.The hydraulic PTO is installed in a closed hull composed of a cover shell and a bottom case, to be completely isolated from seawater.Therefore, the corrosion caused by seawater and the damage caused by extreme waves to PTO are mostly avoided, and the reliability of the WEC will be enhanced significantly.
is proposed.This paper is structured as follows.In Section 2, the novel hydrau system of the ERWEC is introduced in detail.In Section 3, the experimental proc described, and the results are discussed.In Section 4, the multi-objective optim techniques used to determine optimal control parameters are proposed.In Sectio main conclusions are summarized and suggestions for future research are made.

Mechanical Structure of ERWEC
The schematic representation of the ERWEC is shown in Figure 1a.The motio bottom case activated by wave excitation makes the eccentric rotor no longer lo the position with the lowest gravitational potential energy.With the help of gra eccentric rotor will tend to move to the position with the lowest gravitational p energy.The rotational motion of eccentric rotor around vertical axis could be used erate electric energy.The 3D schematic diagram of the device designed accordin principle of ERWEC is shown in Figure 1b.The hydraulic PTO is installed in a clo composed of a cover shell and a bottom case, to be completely isolated from se Therefore, the corrosion caused by seawater and the damage caused by extreme w PTO are mostly avoided, and the reliability of the WEC will be enhanced signific Furthermore, the 1:5 scaled model of the ERWEC, based on Froude similit made of steel plate, was developed, as illustrated in Figure 1c.Two transparent s observation windows are installed on the cover shell, which makes it convenien serve the operation state of the internal hydraulic PTO system and weakens the s effect of the closed metal hull on the wireless data transmission between inside a side electronic modules.Considering the size limitation of the scaled physical mod one small hydraulic accumulator is used in the closed shell.
About the scaled model, the length of the bottom case is 1500 mm, the width mm, the overall height is 862 mm, the draught is 320 mm, the center of buoyanc mm below the waterline, and the center of gravity is 60 mm above the waterline.Furthermore, the 1:5 scaled model of the ERWEC, based on Froude similitude and made of steel plate, was developed, as illustrated in Figure 1c.Two transparent silica gel observation windows are installed on the cover shell, which makes it convenient to observe the operation state of the internal hydraulic PTO system and weakens the shielding effect of the closed metal hull on the wireless data transmission between inside and outside electronic modules.Considering the size limitation of the scaled physical model, only one small hydraulic accumulator is used in the closed shell.
About the scaled model, the length of the bottom case is 1500 mm, the width is 1000 mm, the overall height is 862 mm, the draught is 320 mm, the center of buoyancy is 110 mm below the waterline, and the center of gravity is 60 mm above the waterline.

Principle of Hydraulic PTO
The schematic diagram of hydraulic PTO is presented in Figure 2.

Principle of Hydraulic PTO
The schematic diagram of hydraulic PTO is presented in Figure 2 According to the components of hydraulic PTO, the hydraulic p low-pressure oil to high-pressure oil.In order to adapt to the change o tion of the eccentric rotor, the two-way gear hydraulic pump is used.M valves are used to compose the hydraulic rectifier circuit, which will enter the accumulator from the oil tank, no matter the rotation direc hydraulic pump.The pressure transmitter (a) is installed on the main o the oil pressure of the hydraulic accumulator, which is a key paramete to open the electromagnetic switch valve.The hydraulic accumulator, electromagnetic switch valve, is used to store the unstable high-press draulic pump, and drive the hydraulic motor as stably as possible.The is used to adjust the eccentricity of the eccentric rotor.Benefited from centricity can be adjusted automatically according to the oil pressur flow control valve is designed to control the rotational speed of the make the output electric energy stable, which will be studied in the fu motor can be driven by high-pressure oil and then drive the electric g electricity.If the oil in the hydraulic circuit is too high, the relief valve the security of hydraulic PTO.
With the wave excitation, the eccentric rotor will rotate around According to the components of hydraulic PTO, the hydraulic pump could convert low-pressure oil to high-pressure oil.In order to adapt to the change of the rotation direction of the eccentric rotor, the two-way gear hydraulic pump is used.Moreover, four check valves are used to compose the hydraulic rectifier circuit, which will make hydraulic oil enter the accumulator from the oil tank, no matter the rotation direction changes of the hydraulic pump.The pressure transmitter (a) is installed on the main oil circuit to monitor the oil pressure of the hydraulic accumulator, which is a key parameter to decide whether to open the electromagnetic switch valve.The hydraulic accumulator, with the help of the electromagnetic switch valve, is used to store the unstable high-pressure oil from the hydraulic pump, and drive the hydraulic motor as stably as possible.The hydraulic cylinder is used to adjust the eccentricity of the eccentric rotor.Benefited from the spring, the eccentricity can be adjusted automatically according to the oil pressure.The proportional flow control valve is designed to control the rotational speed of the hydraulic motor to make the output electric energy stable, which will be studied in the future.The hydraulic motor can be driven by high-pressure oil and then drive the electric generator to produce electricity.If the oil in the hydraulic circuit is too high, the relief valve will work to ensure the security of hydraulic PTO.
With the wave excitation, the eccentric rotor will rotate around the vertical axis (as shown in Figure 1) and drive the input shaft of the speed increase gearbox to rotate, which results in a larger speed of the output shaft and drives the hydraulic pump to rotate.When the hydraulic pump rotates clockwise, the hydraulic oil flows to the hydraulic accumulator through check valve (d) and check valve (b), in sequence.On the contrary, the hydraulic oil flows to the hydraulic accumulator through check valve (a) and check valve (c), in sequence, when the hydraulic pump rotates counterclockwise.Thus, the two-way rotation of the eccentric rotor is able to drive the PTO system to generate electricity through the hydraulic circuit formed by the four check valves.
Under the same wave excitation, the increased eccentricity will increase the force arm and the torque acting on the central shaft.Then, a large rotation speed of the eccentric rotor can be obtained, which will make a large output flow and a large output pressure of the hydraulic pump.When the wave conditions change, the pressure of hydraulic oil entering the rod cavity of hydraulic cylinder through port B (as shown in Figure 2) increases with the increasement of the speed of the hydraulic pump, causing the reduction in the rotor eccentricity as the spring is compressed and the piston rod retracts.The reduced eccentricity results in a lower speed of the eccentric rotor.On the contrary, if the hydraulic pump has a low speed, the eccentricity will be increased due to the difference between the spring force and the force from hydraulic oil pressure.Hence, the eccentric rotor will be sped up.With the help of the spring in the rodless chamber of the hydraulic cylinder, the hydraulic PTO system implements the sea state adaptive energy capture process of the ERWEC.The active control module of the hydraulic PTO system consists of electromagnetic switch valve and proportional flow valve.The former is used to control the energy accumulation and release of the hydraulic accumulator, and the latter has the capacity for real-time adjustment of the PTO damper.The coordination of the two valves can achieve the regulation of PTO under complex working conditions.

Physical Model of Hydraulic PTO System
On the basis of the schematic diagram of the hydraulic PTO system, the physical model has been constructed, as shown in Figure 3.
J. Mar.Sci.Eng.2023, 11, x FOR PEER REVIEW the hydraulic pump.When the wave conditions change, the pressure of hy tering the rod cavity of hydraulic cylinder through port B (as shown in Figu with the increasement of the speed of the hydraulic pump, causing the re rotor eccentricity as the spring is compressed and the piston rod retracts eccentricity results in a lower speed of the eccentric rotor.On the contrary, i pump has a low speed, the eccentricity will be increased due to the differen spring force and the force from hydraulic oil pressure.Hence, the eccentri sped up.With the help of the spring in the rodless chamber of the hydraul hydraulic PTO system implements the sea state adaptive energy capture ERWEC.The active control module of the hydraulic PTO system consists netic switch valve and proportional flow valve.The former is used to cont accumulation and release of the hydraulic accumulator, and the latter has t real-time adjustment of the PTO damper.The coordination of the two valv the regulation of PTO under complex working conditions.

Physical Model of Hydraulic PTO System
On the basis of the schematic diagram of the hydraulic PTO system model has been constructed, as shown in Figure 3.The data collector could acquire the measurement values of the pressu in the hydraulic PTO system and the output power values of the electric g as output voltage and output current.The collected data could be transfe The data collector could acquire the measurement values of the pressure transmitter in the hydraulic PTO system and the output power values of the electric generator, such as output voltage and output current.The collected data could be transferred to a computer wirelessly.In the computer terminal, the control parameters could be sent to the controller to generate a control signal, and then the control process of the electromagnetic switch valve could be achieved.The state of the electromagnetic switch valve could directly affect the process of energy accumulation and release of the hydraulic accumulator.Thus, the control signal of the electromagnetic switch valve is equivalent to the control signal of the hydraulic accumulator.The electric generator is connected with a fixed resistance in series to measure the output current and the load on the electric generator is unchanged.The oil tank is used to store the oil needed to ensure the work of the hydraulic system.
In order to analyze the effects of control parameters of the accumulator on the energy conversation performance, the natural parameter of each hydraulic component in the PTO system should be determined.According to scale factor and energy input capacity, the rated power of the electric generator was set as 50 W. Considering the relation between output efficiency and rotational speed of hydraulic motor, the rated speed electric generator was set as 500 r/min, which was the reasonable value to make most hydraulic motors achieve optimal efficiency.In terms of hydraulic pump, the optimum rotational speed was about 1000 r/min.The rotational speed of the eccentric rotor was not high, from about 10 r/min to 50 r/min, so the speed increase gearbox with a large ratio was needed.The ratio of speed increase gearbox was set as 40:1.Under the artificial input motion conditions, the hydraulic pressure was from about 3 MPa to 5 MPa.Then, the displacement of the hydraulic pump can be calculated by the equation of P = pq/60, where P and p can be set as 50 W and 3 MPa, respectively, and the calculated result of displacement was 1 cc/rev.According to mass conservation law, the displacement of the hydraulic motor was about 2 cc/rev.Considering the space limitation of the physical model, the volume of the accumulator was set as 6.3 L. According to the manual of hydraulic components, the output pressure of the appropriated hydraulic pump was 10 MPa considering the displacement and efficiency, and the parameters of the hydraulic components in the PTO system are shown in Table 1.In this research, the influences of hydraulic accumulator control strategy on the energy conversion process were emphasized, and that of eccentricity was negligible.In the experiment process, the eccentricity was mechanically set at 250 mm.

Control Strategy of Hydraulic Accumulator
The physical model experiment of the hydraulic PTO system was carried out on land.The dry experiment has been widely used to analyze the dynamics of the proposed PTO as well as its feasibility and reliability.Due to the lack of wave excitation conditions, artificial excitation was used to make the eccentric rotor oscillate in the horizontal plane, as shown in Figure 4.The oscillating angle variation law of the eccentric rotor can be defined where the values of π/2 rad and 2.25 s represent the oscillating angle ampl riod, respectively, tw is the oscillating time, A(tw) and T(tw) are the disturban ing angle amplitude and oscillating period, respectively.Both A(tw) and T(tw) terms produced by artificial excitation, which can be used to simulate the pendulum with uncertain disturbance and analyze the energy conversion eff draulic PTO system.
During the experiments, when the electromagnetic switch valve 6 was open state, the energy accumulation and release process of the hydraulic could not be actively controlled.The output power time history curve of th erator is shown in Figure 5.The oscillating angle variation law of the eccentric rotor can be defined as where the values of π/2 rad and 2.25 s represent the oscillating angle amplitude and period, respectively, t w is the oscillating time, A(t w ) and T(t w ) are the disturbances of oscillating angle amplitude and oscillating period, respectively.Both A(t w ) and T(t w ) are imprecise terms produced by artificial excitation, which can be used to simulate the motion of the pendulum with uncertain disturbance and analyze the energy conversion effect of the hydraulic PTO system.
During the experiments, when the electromagnetic switch valve 6 was always in the open state, the energy accumulation and release process of the hydraulic accumulator could not be actively controlled.The output power time history curve of the electric generator is shown in Figure 5.The oscillating angle variation law of the eccentric rotor ( ) ( ) where the values of π/2 rad and 2.25 s represent the oscillati riod, respectively, tw is the oscillating time, A(tw) and T(tw) are ing angle amplitude and oscillating period, respectively.Both terms produced by artificial excitation, which can be used to pendulum with uncertain disturbance and analyze the energy draulic PTO system.
During the experiments, when the electromagnetic switc open state, the energy accumulation and release process of could not be actively controlled.The output power time histo erator is shown in Figure 5.It can be seen from Figure 5 that the output power of the e The maximum power is about 9 W, the minimum peak power It can be seen from Figure 5 that the output power of the electric generator is unstable.The maximum power is about 9 W, the minimum peak power is about 5 W, the minimum power is 0 W, and the change period is about 1.1 s.
The accumulator, which is employed as an energy storage device, has the capacity of stabilizing the flow and pressure of the hydraulic PTO system.The desired powersmoothing effect is subject to several constraints, such as volumes and pressures [14,18].Aiming to improve the adaptive capacity of the device, an electromagnetic switch valve is employed to control the energy storage process of the accumulator.Three parameters, i.e., trigger pressure, delay time, and open state duration are particularly important to achieve the optimal power-smoothing and conversion.A reasonable control strategy of the hydraulic accumulator has been designed, as shown in Figure 6.
J. Mar.Sci.Eng.2023, 11, x FOR PEER REVIEW the optimal power-smoothing and conversion.A reasonable control strategy of draulic accumulator has been designed, as shown in Figure 6.To determine whether the pressure value is higher than p repeatedly.If the pressure value is still higher than p, repeat Step (2).Otherwise, Step (4) will be performed.

4.
To close the electromagnetic switch valve, the accumulator will switch to the state of energy accumulation.Repeat Steps (1-3) successively after the pressure value reaches p.
Therefore, the trigger pressure p, the delay time t between the generation of the trigger signal and the release of the accumulated energy, and the open state duration dt of the electromagnetic switch valve keeping the open state are selected as the control variables.During the experiments, the trigger pressure p was set to 2.5 MPa, 3.0 MPa, 3.5 MPa, and 4.0 MPa, respectively, the delay time t was set to 0.5 s, 1.0 s, 1.5 s, and 2.0 s, respectively, and the open state duration dt was set to 3.0 s, 4.0 s, 5.0 s, and 6.0 s, respectively.Then, the influences of control variables on output power were analyzed.
The total amount value of output power produced by the electric generator over a certain period and the stability of output power are important indicators to evaluate the energy conversion performance of the hydraulic PTO system.Therefore, the average output power and power fluctuation index are used to measure the amount value and the stability of output power, respectively.
The average output power of the electric generator at t duration can be defined as The average value of the first-order differential cumulant of output power is adopted as the power fluctuation index, which can be defined as where p i , p i−1 are the power at time i and i−1, respectively, n is the number of time intervals, p t is the average output power defined in Equation (2), and p e is the power fluctuation index.The difference in output power reflects the continuous change in output power.It has the capacity of capturing periodic stability of output power approximating a square wave.Therefore, Equation ( 3) is used to reflect the characteristic of stability.

Influence of Trigger Pressure on Output Power
The delay time t and the open state duration dt are fixed at 1.0 s and 4.0 s, respectively.The trigger pressure is changed to analyze its influence on the output power of the electric generator.The time history curves of output power obtained from the experiment are shown in Figure 7.The time history curves of pressure values recorded by transmitters 17 (a) and 17 (b) when the trigger pressure is 4 MPa are taken as an example, as shown in Figure 8, which is related to Figure 7d.It can be seen that the output power is obtained one second after the pressure value at transmitter 17 (a) reached the trigger pressure.Meanwhile, the pressure value at transmitter 17 (a) decreases lightly, and the pressure value at transmitter 17 (b) increases greatly.The energy output process lasts for four seconds.Then, the pressure value at transmitter 17 (b) decreases to zero suddenly, and the pressure value at transmitter 17 (a) increases lightly.Thus, the pressure changing curve illustrates the power changing curve clearly.
The average values of output power and power fluctuation index under different trigger pressure conditions are shown in Figure 9.
It can be seen from Figure 9 that the average power has a tendency of decreasing first and then increasing.The average power reaches a low point at a trigger pressure of 3.0 MPa.As the trigger pressure increases, the power fluctuation index gradually drops to its lowest point.When the trigger pressure is 4 MPa, the average output power reaches the maximum and the power fluctuation index is the minimum, indicating that the output energy of the hydraulic PTO system is large and that the power conversion process is stable under this condition.
Meanwhile, the pressure value at transmitter 17 (a) decreases lightly, and the pressure value at transmitter 17 (b) increases greatly.The energy output process lasts for four seconds.Then, the pressure value at transmitter 17 (b) decreases to zero suddenly, and the pressure value at transmitter 17 (a) increases lightly.Thus, the pressure changing curve illustrates the power changing curve clearly.The average values of output power and power fluctuation index unde trigger pressure conditions are shown in Figure 9.The average values of output power and power fluctuation index u trigger pressure conditions are shown in Figure 9.It can be seen from Figure 9 that the average power has a tendency of d and then increasing.The average power reaches a low point at a trigger p MPa.As the trigger pressure increases, the power fluctuation index gradual lowest point.When the trigger pressure is 4 MPa, the average output pow maximum and the power fluctuation index is the minimum, indicating th energy of the hydraulic PTO system is large and that the power convers stable under this condition.

Influence of Delay Time on Output Power
The trigger pressure p is kept at 3.5 MPa, and the open state duration d s to analyze the influence of delay time t on the output power.The time his output power obtained from the experiments are shown in Figure 10.

Influence of Delay Time on Output Power
The trigger pressure p is kept at 3.5 MPa, and the open state duration dt is kept at 4.0 s to analyze the influence of delay time t on the output power.The time history curves of output power obtained from the experiments are shown in Figure 10.The average output power and power fluctuation index under different delay times are shown in Figure 10.
It can be seen from Figure 11 that the average output power has the smallest value when the delay time is 0.5 s; meanwhile, the power fluctuation index is at its maximum, which indicates that the hydraulic PTO system has bad output energy ability and poor power conversion stability.When the delay time reaches 1.0 s, the power fluctuation index is the minimum, but the average output power value is not large.The average output power reaches the maximum point at a delay time of 1.5 s, but the power fluctuation index has a larger value as well.When the delay time is 2.0 s, a relatively large average output power, and a small power fluctuation index can be obtained, indicating that the performance of the hydraulic PTO system is acceptable under this condition.The average output power and power fluctuation index under different delay times are shown in Figure 10.
It can be seen from Figure 11 that the average output power has the smallest value when the delay time is 0.5 s; meanwhile, the power fluctuation index is at its maximum, which indicates that the hydraulic PTO system has bad output energy ability and poor power conversion stability.When the delay time reaches 1.0 s, the power fluctuation index is the minimum, but the average output power value is not large.The average output power reaches the maximum point at a delay time of 1.5 s, but the power fluctuation index has a larger value as well.When the delay time is 2.0 s, a relatively large average output power, and a small power fluctuation index can be obtained, indicating that the performance of the hydraulic PTO system is acceptable under this condition.
when the delay time is 0.5 s; meanwhile, the power fluctuation index is at which indicates that the hydraulic PTO system has bad output energy abi power conversion stability.When the delay time reaches 1.0 s, the power fluc is the minimum, but the average output power value is not large.The av power reaches the maximum point at a delay time of 1.5 s, but the power fluc has a larger value as well.When the delay time is 2.0 s, a relatively large av power, and a small power fluctuation index can be obtained, indicating th mance of the hydraulic PTO system is acceptable under this condition.Furthermore, the open state duration dt is maintained at 4.0 s, and the sure p is increased to 4.0 MPa.The influence of delay time t on the output Furthermore, the open state duration dt is maintained at 4.0 s, and the trigger pressure p is increased to 4.0 MPa.The influence of delay time t on the output power of the electric generator is analyzed.The time history of output power, the average output power, and the power fluctuation index under different delay time conditions are shown in Figures 12 and 13.
electric generator is analyzed.The time history curves of output power, the average output power, and the power fluctuation index under different delay time conditions are shown in Figures 12 and 13     It can be seen from Figures 11 and 13 that the average output power the power fluctuation index decreases visibly after increasing the trigger power fluctuation index is at a lower level and does not change as the delay t This phenomenon reveals that the power fluctuation index is not sensitive under the trigger pressure of 4.0 MPa.It can be seen from Figures 11 and 13 that the average output power increases and the power fluctuation index decreases visibly after increasing the trigger pressure.The power fluctuation index is at a lower level and does not change as the delay time increases.This phenomenon reveals that the power fluctuation index is not sensitive to time under the trigger pressure of 4.0

Influence of Open State Duration on Output Power
The influence of open state duration dt on the output power of the electric generator is analyzed at the trigger pressure p of 3.5 MPa and the delay time t of 1.0 s.The time history curves of output power obtained from the experiment are shown in Figure 14.

Influence of Open State Duration on Output Power
The influence of open state duration dt on the output power of the electric generator is analyzed at the trigger pressure p of 3.5 MPa and the delay time t of 1.0 s.The time history curves of output power obtained from the experiment are shown in Figure 14.It can be seen from Figure 15 that the average output power remains roughly c at around 7 W.However, the power fluctuation index changes significantly with t state duration.This shows that the average value of output power under this con not sensitive to the open state duration, while the power fluctuation index is the o Moreover, the delay time t is maintained at 1.0 s and the trigger pressure creased to 4.0 MPa to analyze the influence of the open state duration t on the It can be seen from Figure 15 that the average output power remains roughly constant at around 7 W.However, the power fluctuation index changes significantly with the open state duration.This shows that the average value of output power under this condition is not sensitive to the open state duration, while the power fluctuation index is the opposite.
Moreover, the delay time t is maintained at 1.0 s and the trigger pressure p is increased to 4.0 MPa to analyze the influence of the open state duration t on the output power.The time history curves of output power obtained from the experiment are shown in Figure 16.As shown in Figure 17, when the open state duration is 4.0 s, the average output power falls to a low point, and it reaches the peak at the open state duration of 6.0 s.The power fluctuation index does not change with the increase in the open state duration, indicating that the power fluctuation index is not sensitive to the open state duration under As shown in Figure 17, when the open state duration is 4.0 s, the average output power falls to a low point, and it reaches the peak at the open state duration of 6.0 s.The power fluctuation index does not change with the increase in the open state duration, indicating that the power fluctuation index is not sensitive to the open state duration under this condition.As shown in Figure 17, when the open state duration is 4.0 s, the av power falls to a low point, and it reaches the peak at the open state duratio power fluctuation index does not change with the increase in the open state dicating that the power fluctuation index is not sensitive to the open state d this condition.

Analysis of Experimental Results
Based on the experimental results, it can be seen that the trigger pressu significant factor affecting the output power amount and stability of the h system.More energy will be accumulated if the trigger pressure has a large the role of the accumulator in reducing flow and pressure fluctuation will b make the output power more stable.However, the internal pressure of the

Analysis of Experimental Results
Based on the experimental results, it can be seen that the trigger pressure is the most significant factor affecting the output power amount and stability of the hydraulic PTO system.More energy will be accumulated if the trigger pressure has a larger value.Then, the role of the accumulator in reducing flow and pressure fluctuation will be amplified to make the output power more stable.However, the internal pressure of the accumulator also acts on the outlet of the hydraulic pump to cause resistance torque, which will affect the rotational motion of the eccentric rotor.When the internal pressure of the accumulator is too large, it may even make the eccentric rotor unable to oscillate.Therefore, a large trigger pressure does not mean good power performance.A reasonable range of trigger pressure should be determined to optimize the power conversion of hydraulic PTO.
Under different trigger pressures, the effects of delay time on average output power are similar, but the effects on the power fluctuation index are rather different.By setting the delay time, it is possible to reduce the spurious triggering phenomenon on the electromagnetic switch valve caused by the pressure fluctuation of the hydraulic PTO system.When the trigger pressure is small, the pressure fluctuation is more likely to cause the spurious triggering phenomenon and make the accumulator enter the energy-releasing state in advance.Therefore, a longer delay time should be set.However, a too-long delay time also has the possibility of making the high-pressure energy in the hydraulic PTO system unable to be released in time.The oscillation of the eccentric rotor will be affected due to the increase in the internal pressure of the hydraulic accumulator.Therefore, a reasonable delay time should be selected under the determined trigger pressure.
Similar to the influences of delay time, under different trigger pressure conditions, the influence of the open state duration of the electromagnetic switch valve on the average output power is small, but there is a significantly different effect on the power fluctua-tion index.By setting the open state duration, the amount of energy released from the accumulator can be controlled.If the open state lasts for a short time, the energy of the accumulator cannot be fully released, resulting in the low energy conversion efficiency of the hydraulic PTO.If the open state lasts for a long time, the accumulator cannot reach a high energy storage pressure under the open state of the electromagnetic switch valve after the energy of the accumulator is completely released.That will weaken the energy storage effect.Therefore, there is also an optimal range for the open-state duration of the electromagnetic switch valve.
Compared to the studies in [23,24], the results show that the proposed PTO system has the capacity of increasing the stability of output power in the power generation phase.In addition, it can be seen from the experimental results that the influences of the three factors of trigger pressure, delay time, and the open state duration have a coupled relationship with the output power performance.Therefore, it is necessary to use an intelligent optimization algorithm to obtain the optimal value range of three control parameters of the hydraulic accumulator.

Experimental Samples Based on Optimal Latin Hypercube Sampling
Based on the analysis in Section 3, the ranges of trigger pressure p, delay time t, and open state duration dt are set as (3 MPa, 4 MPa), (0.5 s, 2 s), and (2 s, 6 s), respectively.More experiments are needed to quantify the regression relationship between the three independent variables of trigger pressure, delay time, open state duration, and the two dependent variables of average output power and power fluctuation index.To reduce experimental workload, the OLHS method is used to design experimental samples, in which the sample space is covered as far as possible using fewer examples.According to the ranges mentioned above, a total of 40 groups of physical model experiments are set up.The combinations of parameters and results are shown in Table 2.

Sensitivity Analysis of Output Power
The effects of trigger pressure, delay time, and open state duration on output power performance are strongly coupled, and it is difficult to establish their parametric regression models.The advantages of GP are that relationships among variables can be obtained, the model interpolates the data, and the model is probabilistic so that the empirical confidence intervals can be computed [25,26].Therefore, the GPR method was used to establish a nonparametric agent model between control parameters and the output power of the hydraulic PTO system.The experimental groups of 1-5, 7-29, and 31-40 from Table 2 were selected as training data to establish the Gaussian regression model.The hyper-parameters of the kernel function were determined by the Bayesian optimizer [25].The Gaussian process GP1 was trained by taking the trigger pressure, delay time, and open state duration as the inputs and the average of the output power as the output.The Gaussian process GP2 using the power fluctuation index as an output parameter was obtained in the same inputs as GP1.In order to verify the accuracy of the nonparametric agent model, the above two Gaussian processes were used to predict average output power and power fluctuation index.The predicted data were compared with the validating data, including the 6th and 30th experimental results.The comparison results are shown in Table 3.As shown in Table 3, the nonparametric agent model of GPR has high prediction accuracy, which means it has the capacity of analyzing parameter sensitivity and optimizing control parameters.
Furthermore, the weight factors of control parameters on output power characteristics were calculated through the Sobol' global sensitivity analysis method [27].In this process, the numbers of input variables, sampling times, and total evaluation numbers were set as 3, 4800 and 24,000.The MATLAB SAFE toolbox is conventional to calculate the sensitivity indexes based on the obtained Gaussian process models.Taking the total effect sensitivity values of the power fluctuation index to the control parameters as an example, the variation curves of the sensitivity coefficients with the number of evaluations are shown in Figure 18.
cess, the numbers of input variables, sampling times, and total evaluation numbers were set as 3, 4800 and 24,000.The MATLAB SAFE toolbox is conventional to calculate the sensitivity indexes based on the obtained Gaussian process models.Taking the total effect sensitivity values of the power fluctuation index to the control parameters as an example the variation curves of the sensitivity coefficients with the number of evaluations are shown in Figure 18.It can be seen from Figure 18 that the sensitivity coefficient converges after the evaluation number reaches 20,000.The sensitivity values of average output power and power fluctuation index to control parameters are shown in Figure 19.It can be seen from Figure 18 that the sensitivity coefficient converges after the evaluation number reaches 20,000.The sensitivity values of average output power and power fluctuation index to control parameters are shown in Figure 19.It can be seen that the trigger pressure has a significant effect on the average output power and power fluctuation index.Moreover, the influences of delay time and open state duration on average output power and power fluctuation index are similar and are lower than those of trigger pressure.The differences between the total effect and the main effect can be regarded as the results of coupled effects.Therefore, the coupled effects of delay time and open state duration on the power fluctuation index are greater than those on the average output power.

Optimization of Control Parameters
In order to improve output power and stability, the three control parameters of trigger pressure, delay time, and open state duration were optimized based on the PlatEMO [28] and NSGA-Ш multi-objective genetic algorithms, where the minimum value of the reciprocal of average output power (e.g., the maximum average output power) and the minimum value of power fluctuation index were taken as the optimization objectives.The NSGA-Ш method could improve the capability of Pareto-based multi-objective evolutionary algorithms for most objective optimization problems by modifying the diversity operator based on a reference-point strategy [29].The major procedure of NSGA-Ш is introduced in Figure 20.Pt and St are the parents and descendants of sizes N at the tth iteration.The population of the offspring Rt is 2N after combining Pt and St.Moreover, F1, F2… are the non-dominated fronts, and t max is the maximum evaluation number.A detailed description of NSGA-Ш can be found in [29,30].In the multi-objective optimization algorithm of this study, the size of the population was set as 200, and the evaluation number It can be seen that the trigger pressure has a significant effect on the average output power and power fluctuation index.Moreover, the influences of delay time and open state duration on average output power and power fluctuation index are similar and are lower than those of trigger pressure.The differences between the total effect and the main effect can be regarded as the results of coupled effects.Therefore, the coupled effects of delay time and open state duration on the power fluctuation index are greater than those on the average output power.

Optimization of Control Parameters
In order to improve output power and stability, the three control parameters of trigger pressure, delay time, and open state duration were optimized based on the PlatEMO [28] and NSGA-III multi-objective genetic algorithms, where the minimum value of the reciprocal of average output power (e.g., the maximum average output power) and the minimum value of power fluctuation index were taken as the optimization objectives.The NSGA-III method could improve the capability of Pareto-based multi-objective evolutionary algorithms for most objective optimization problems by modifying the diversity operator based on a reference-point strategy [29].The major procedure of NSGA-III is introduced in Figure 20.P t and S t are the parents and descendants of sizes N at the tth iteration.The population of the offspring R t is 2N after combining P t and S t .Moreover, F 1 , F 2 . . .are the non-dominated fronts, and t max is the maximum evaluation number.A detailed description of NSGA-III can be found in [29,30].In the multi-objective optimization algorithm of this study, the size of the population was set as 200, and the evaluation number was set as 12,000.The Pareto frontiers of optimal solution sets for control parameters of the hydraulic accumulator were calculated, as presented in Figure 21.Part of the solution sets are shown in Table 4.According to the requirements of the ERWEC for the output power performance of the hydraulic PTO system, the applicable control parameters of the accumulator, such as trigger pressure, delay time, and open state duration, can be obtained based on the optimization results in Figure 20 and Table 4.This process provides a reference for real-time regulation of the hydraulic PTO system.

Conclusions
In this paper, the novel energy conversion principle of a hydraulic PTO system with an accumulator of an ERWEC is presented.The experiments are conducted with the physical model of the hydraulic PTO system to study the effects of trigger pressure, delay time, and open state duration on average output power and power fluctuation index.Additionally, a numerical method for deriving optimal control parameters of the hydraulic accumulator to maximize output power and stability is put forward.The following significant and useful conclusions can be obtained from the presented results: (1) The effects of trigger pressure, delay time, and open state duration on average output power and power fluctuation index of the hydraulic PTO system are strongly coupled.Among them, trigger pressure has the largest weight factor.Thus, in the process of setting control parameters, trigger pressure, namely the maximum working pressure of the hydraulic accumulator, should be determined first, and then delay time and open state duration could be set. ( The experimental examples are designed based on OLHS, and the nonparameterized agent model between control parameters of accumulator and output power indices is established based on GPR.The sensitivity analysis indicates that the coupled effect of delay time and open state duration on the power fluctuation index is greater than that on average output power.The delay time and open state duration should be considered at the same time to improve the stability of output power. (3) NSGA-III is an effective method to obtain optimal control parameters of hydraulic accumulator with the objectives of average output power and power fluctuation index.The output power and stability are improved through the optimized control parameters.
The research results of this paper will provide bases for parameter settings and realtime control of hydraulic PTO system with accumulators.In the future, the completed physical model of ERWEC will be developed to verify the control parameters optimization effect of the accumulator in the real wave excitation conditions, the effects of accumulator volume and precharge on power conversion performance will be further analyzed, and the real-time control of the PTO system will be achieved as well.

Figure 3 .
Figure 3. Physical model of hydraulic PTO system.

Figure 3 .
Figure 3. Physical model of hydraulic PTO system.

Figure 5 .
Figure 5.The output power time history curve when the electromagnetic switch va the open state.

Figure 5 .
Figure 5.The output power time history curve when the electromag the open state.

Figure 5 .
Figure 5.The output power time history curve when the electromagnetic switch valve is always in the open state.

Figure 6 .
Figure 6.Control logic block diagram of hydraulic accumulator.

Figure 6 .
Figure 6.Control logic block diagram of hydraulic accumulator.1.When the pressure value monitored by pressure transmitter 17 (a) reaches the trigger pressure p, the controller generates a trigger signal to open the electromagnetic switch valve.After delay time t, the electromagnetic switch valve will be opened, and the accumulator begins to release the accumulated energy.Then, Step (2) is executed.2.After the electromagnetic switch valve remains open for the time of open state duration dt, Step (3) will be executed.3.To determine whether the pressure value is higher than p repeatedly.If the pressure value is still higher than p, repeat Step (2).Otherwise, Step (4) will be performed.

Figure 7 .
Figure 7. Output power under different trigger pressures.

Figure 9 .
Figure 9.The average values of output power and power fluctuation index under d pressure conditions.

Figure 9 .
Figure 9.The average values of output power and power fluctuation index under different trigger pressure conditions.

J 22 Figure 10 .
Figure 10.Output power under different delay times (trigger pressure is 3.5 MPa).

Figure 10 .
Figure 10.Output power under different delay times (trigger pressure is 3.5 MPa).

Figure 11 .
Figure 11.The average output power and power fluctuation index under different de ger pressure is 3.5 MPa).

Figure 11 .
Figure 11.The average output power and power fluctuation index under different delay times (trigger pressure is 3.5 MPa). .

Figure 12 .
Figure 12.Output power under different delay times (trigger pressure is 4 MPa).Figure 12. Output power under different delay times (trigger pressure is 4 MPa).

Figure 12 .
Figure 12.Output power under different delay times (trigger pressure is 4 MPa).Figure 12. Output power under different delay times (trigger pressure is 4 MPa).

Figure 12 .
Figure 12.Output power under different delay times (trigger pressure is 4 MPa).

Figure 13 .
Figure 13.The average output power and power fluctuation index under different d ger pressure is 4 MPa).

Figure 13 .
Figure 13.The average output power and power fluctuation index under different delay times (trigger pressure is 4 MPa).

Figure 14 .
Figure 14.Output power under different open state durations (trigger pressure is 3.5 MPa).The average output power of the electric generator and power fluctuation index under different open state durations is shown in Figure15.

Figure 14 .
Figure 14.Output power under different open state durations (trigger pressure is 3.5 MPa).

Figure 14 .
Figure 14.Output power under different open state durations (trigger pressure is 3.5 MPa

Figure 15 .
Figure 15.The average output power and power fluctuation index under different open st tions (trigger pressure is 3.5 MPa).

Figure 15 .
Figure 15.The average output power and power fluctuation index under different open state durations (trigger pressure is 3.5 MPa).

J
. Mar. Sci.Eng.2023, 11, x FOR PEER REVIEW 14 of 22 power.The time history curves of output power obtained from the experiment are shown in Figure 16.

Figure 16 .
Figure 16.Output power under different open state durations (trigger pressure is 4.0 MPa).

Figure 16 .
Figure 16.Output power under different open durations (trigger pressure is 4.0 MPa).

Figure 16 .
Figure 16.Output power under different open state durations (trigger pressure is 4.

Figure 17 .
Figure 17.The average output power and power fluctuation index under different o tions (trigger pressure is 4.0 MPa).

Figure 17 .
Figure 17.The average output power and power fluctuation index under different open state durations (trigger pressure is 4.0 MPa).

Figure 18 .
Figure 18.Variation curves of the sensitivity coefficients with the evaluation number.

Figure 18 .
Figure 18.Variation curves of the sensitivity coefficients with the evaluation number.

Figure 19 .
Figure 19.Sensitivity of average output power and power fluctuation index.(a) Sensitivity of average output power.(b) Sensitivity of power fluctuation index.

Figure 19 .
Figure 19.Sensitivity of average output power and power fluctuation index.(a) Sensitivity of average output power.(b) Sensitivity of power fluctuation index.

Table 1 .
The parameters of hydraulic PTO system components.

Table 2 .
The combination of parameters and results.

Table 3 .
Comparison results between experimental data and predicted data.

Table 4 .
Part of Pareto solution sets.

Table 4 .
Part of Pareto solution sets.