Numerical Study of Scale Effects on Open Water Propeller Performance

: The present study aims to investigate the scale effects of the open water propeller performance using computational ﬂuid dynamics (CFD). The results are presented for the propeller which was previously 3D scanned and digitized. The results obtained using two turbulence models within the numerical simulations are compared. The veriﬁcation study is conducted to assess the numerical uncertainty and thus obtain the optimal grid size for the numerical simulations. A transition model is used at the model scale to account for the partially laminar ﬂow. The propeller is then scaled, and numerical simulations are performed to assess the scale effects on the open water performance of the considered propeller. The results demonstrate the signiﬁcant scale effects on open water characteristics however, scale effects are considerably lower when the transition model is applied within the numerical simulations at the model scale.


Introduction
The open water test (OWT) is carried out in towing tanks to assess the hydrodynamic performance of propellers.These tests are always performed at a model scale since open water tests at full-scale would be expensive and there are no testing sites where such large-scale tests would be feasible.Nowadays, computational fluid dynamics (CFD) is successfully used by many researchers for the assessment of ship propulsion performance.Farkas et al. [1] used numerical simulations for the prediction of the nominal wake in the case of a bulk carrier.The authors noticed significant scale effects in both integral values of nominal wake and circumferential averaged non-dimensional axial velocity distribution.Jang et al. [2] employed numerical simulations of OWT at model scale to assess the influence of pitch motion on the propeller performance.The authors demonstrated that the pitch motion of the ship has a dominant effect on the variation of the propeller performance resulting in the sinusoidal pitch motion of the propeller.Sun et al. [3] used CFD to investigate the vibration and noise reduction effects of an energy-saving device.The obtained results showed that the considered energy-saving device can improve propulsion efficiency and reduce the radiation noise intensity.Multiple different scaling methods have been developed for the extrapolation of the model scale to full-scale results.Helma et al. [4] presented an overview of the different scaling methods and assessed their influence on the full-scale results.The authors divided the scaling methods into statistical, analytical, CFD methods, and a combination of the listed methods.Helma [5] developed a scaling procedure for unconventional propeller designs called the β i method utilizing the equivalent profile concept.The author showed that the method works well with all propeller geometries since it is independent of the blade loading distribution.It is also important to point out that it needs the results from only one set of open water curves.Extrapolation performed by any of the scaling methods provides accurate and reliable results [6], but experimental OWT is cost-intensive and time-consuming.CFD is a reasonable alternative to towing tank tests since it is a versatile tool that can be used to predict ship hydrodynamic characteristics in model and full-scale [7].The authors showed in [7] that the numerical results of the ship resistance in calm water varied from −10% to 4% compared to sea trials data.Mikkelsen and Walther [8] validated the results from the self-propulsion numerical simulations against the results obtained from the sea trials.They showed that the discrepancy between the results can be further lowered using the modified wall functions for the simulation of the surface roughness.The difference between the obtained delivered powers is largely affected by propellers operating at higher Reynolds numbers in full-scale simulations [9].Another problem with extrapolation to full-scale is the fact that the scaling methods are not accurate enough for unconventional propellers [10].Multiple authors addressed this issue by simulating the flow around the full-scale propellers with unconventional geometries such as tip-modified propellers [5,11,12].The hydrodynamic analysis of a tip-loaded propeller was performed using the boundary element method to evaluate the propeller-induced hull pressures in [13].The predicted hull pressures are in good agreement with the ones obtained in the cavitation tunnel and with unsteady RANS equations at the design and moderately loaded conditions.Dong et al. [12] studied the influence of PPTC-II propeller's tip rake on the scale effects by conducting numerical simulations in full-scale and model scale as well as modifying the propeller geometry with and without the tip rake.The authors compared the results with the ones obtained using the ITTC-1978 method and concluded that the ITTC method must be updated to predict the scale effects on the thrust and torque coefficients more precisely.Li et al.The study by [10] also concluded that ITTC should develop new scaling methods for unconventional propellers.Chen et al. [14] studied the open water hydrodynamic performance of a high skew submarine propeller E1619 and concluded that the difference between the predicted torque coefficient using the ITTC 1978 method and the ones obtained by numerical simulations is not negligible.Furthermore, they concluded that the law of scale effect cannot be analyzed using only two models and that several different scales must be considered.Owen et al. [15] investigated the effect of biofouling on the propeller open water performance using numerical simulations at the model scale where multiple methods for propeller rotation modeling were used, i.e., the moving reference frame (MRF) method and sliding mesh (SM) approach.Minor discrepancies between the open water results obtained from the two methods were shown; thus, the authors decided to retain the MRF method since it is computationally less expensive.The same method was used in [16,17] since it lowers the computational time, and the convergence is faster than using the overset mesh (OM) method.Mikkelsen et al. [18] also used the MRF method for open water simulations; however, in the case of self-propulsion simulations, the MRF method was used only to initialize the flow around the propeller followed by the SM method for the rest of the simulation.A comparison of SM and OM methods was given in [19] for the case of a rotating vertical axis turbine.The authors showed that by increasing the number of cells the results converge faster using the OM method at the cost of 10% higher computational time.Wang et al. [20] used a single-run procedure and OM method to determine the open water curves.The results were compared to the experimental results performed by IIHR (available at the Tokyo 2015 CFD Workshop [21]) and an overall agreement between the results was shown.Bekhit and Lungu [22] performed numerical simulations of resistance and self-propulsion tests with and without the rudder as well as OWT.The obtained results were compared with experimental results, showing an average error of about 3% for the thrust coefficient and 7% for the torque coefficient.Lungu [23] in his later study performed numerical simulations of the resistance, open water, and selfpropulsion tests of a 3600 TEU containership, where he showed a 5% difference between the measurements and numerical predictions of thrust and torque coefficients.Farkas et al. [24] compared two methods for assessing the influence of biofouling on the open water propeller characteristics.The verification and validation study were performed for three full-scale propellers and satisfactory agreement was achieved.These results were compared with the results obtained using a propeller performance prediction method for fouled surfaces.The impact of hard fouling on the ship hydrodynamic performance was assessed in [25], where the authors conducted full-scale CFD simulations of OWT for three propellers and validated the results using the towing tank results.Farkas et al. [26] investigated the effects of biofilm on ship propulsion characteristics.The authors demonstrated the significant impact of biofilm on the ship hydrodynamic performance highlighting the importance of keeping the hull clean.Dogrul [27] investigated the scale effects of a self-propelled submarine where he compared the extrapolated numerical results with the results from full-scale simulations.Gonzalez-Adalid et al. [28] conducted model scale and full-scale numerical simulations for the determination of the performance of two unconventional propellers with the transition model.Good agreement was shown between the results obtained from the fully turbulent, full-scale simulations and the sea trial data.Baltazar et al. [29] also performed the numerical simulations with the transition model at the model scale, but in addition, the paint test results were used for the validation study.The authors showed an increase in thrust of 2-4% when using the transition model.Moran-Guerrero et al. [30] used an improved Gamma Reynolds Theta (γ − Re θ ) correlation-based model for transition prediction, which considers the crossflow effects.Pawar and Brizzolara [31] used the same transition model to simulate the OWT of an open and ducted propeller to assess the discrepancies between experimental and numerical results.
The focus of this study is the investigation of the scale effects of the open water propeller performance.The numerical simulations are conducted for multiple scales ranging from model scale to full-scale.First, the verification study is conducted using the grid convergence index (GCI) method, and the results of the numerical simulations are presented.The rest of the paper is organized as follows: the numerical model and the grid generation are described within Methods section.The results are presented and briefly discussed in the Results section and discussion followed by the conclusions from the present study in the last section.

Numerical Modeling
The numerical simulations in this study are based on the Reynolds-averaged Navier-Stokes (RANS) equations.For the case of an incompressible fluid, continuity and momentum transport equations for unsteady flow are written as: where u i is the averaged Cartesian components of the velocity vector, ρu i u j is the Reynolds stress tensor (RST), p is the mean pressure, and τ ij is the mean viscous stress tensor defined as: where µ is the dynamic viscosity of the fluid.
To discretize the governing equations, the finite volume method (FVM) is used in the simulations.Within the numerical simulations, the shear stress transport k − ω (SSTKO) turbulence model is used to close the system of discretized differential equations since it is accurate enough in the near wall and far-field region [32].The SSTKO is compared with the realizable k − ε (RKE) turbulence model.
The rotation of the propeller can be modeled using three approaches, i.e., SM, OM, and steady-state simulation using the MRF.In this study, the MRF method [33] is used since it is computationally more efficient compared to the other two approaches [15].The MRF is a steady-state method that consists of a rotating flow around a stationary mesh.

Turbulence Models
RANS turbulence models are based on the modeling of RST which is expressed as a function of the mean flow quantities.The turbulence models applied in this study use the concept of turbulent eddy viscosity µ t to model RST.

Realizable k − ε(RKE) Turbulence Model
This is a two-equation model that solves transport equations for the turbulent kinetic energy k and the turbulent dissipation rate ε.The eddy viscosity in this model is described with the following equation: where C µ is the model coefficient.
The transport equations for k and ε within the RKE model are defined as: where u i is the averaged velocity vector, f c is the curvature correction factor, G k is the turbulent production term, σ k and σ ε are turbulent Schmidt numbers, G B is the buoyancy production term, ε 0 is the ambient turbulence value that counteracts turbulence decay, Υ is the dilatation dissipation, C ε1 , C ε2 and C ε3 are the model depending coefficients, S is the modulus of the mean strain tensor, and finally S k and S ε are the user-defined source terms.

Shear Stress Transport k − ω (SSTKO) Turbulence Model
The modified standard k − ω model blends k − ε model in the far field with the k − ω model near the walls.Turbulent eddy viscosity in this model is given by the following equation: where T is the turbulent time scale.The k − ω turbulence model solves two transport equations for the turbulent kinetic energy k and the specific dissipation ω: where σ k , σ ω , β, β * are the model depending coefficients, G nl is the non-linear production term, f β * is the free-shear modification factor, f β is the vortex-stretching modification factor, and finally k 0 and ω 0 are the ambient values that counteract turbulence decay.

Transition Model
The turbulence model assumes that the flow is turbulent in the whole flow region.Within the numerical simulations at the model scale, the flow is expected to be partly laminar.To model the transition from laminar to turbulent flow, a transition model should be applied.The correlation-based γ − Re θ transition model is used within the numerical simulations because it is coupled with the SSTKO turbulence model.The transition model solves two additional transport equations, i.e., intermittency γ and transition momentum thickness Reynolds number Re θt which read as follows: where U j is the mean velocity vector, P γ and P θt are the production terms, E γ is the destruction term, σ f and σ θt are the model coefficients.More information on the production, destruction terms and model coefficients can be found in [34].To accurately solve the laminar and transitional boundary layers, the first cell near the wall must have y + ≤ 1 [29].
Because of this constraint, it is decided to disable the transition model at other scales.

Open Water Propeller Characteristics
The open water characteristics of a propeller consist of determining the forces and moments acting on the propeller which is operating in a uniform stream without the influence of the hull.To obtain the open water curves, thrust K T and torque K Q coefficients need to be determined as functions of the advance coefficient J.The thrust and torque coefficients are defined using the following equations: where T and Q are the thrust and torque, respectively, ρ is the fluid density, n the propeller rate of revolution, and D the propeller diameter.The advance coefficient is defined as follows: where v A is the speed of advance.
Finally, propeller open water efficiency η o is defined by:

Grid Generation
The computational domain is defined as a cylinder that encloses the propeller with the hub and shaft.The domain boundaries are placed sufficiently far from the propeller to avoid their influence on the obtained results.Figure 1 shows the computational domain with the respective dimensions.
For the discretization of the computational domain, the unstructured hexahedral mesh is used.The numerical simulations with the transition model are performed with a grid that has y + ≤ 1, while the remaining simulations are performed with a grid that has y + > 30 [35].To obtain the required y + values, the distance from the wall to the center of the first prism layer is determined using the following equation:

Grid Generation
The computational domain is defined as a cylinder that encloses the propeller with the hub and shaft.The domain boundaries are placed sufficiently far from the propeller to avoid their influence on the obtained results.Figure 1 shows the computational domain with the respective dimensions.For the discretization of the computational domain, the unstructured hexahedral mesh is used.The numerical simulations with the transition model are performed with a grid that has 1 y + ≤ , while the remaining simulations are performed with a grid that has 30 y + > [35].To obtain the required y + values, the distance from the wall to the center of the first prism layer is determined using the following equation: The frictional velocity u τ is calculated as follows: where the wall shear stress w τ is calculated using the skin friction coefficient f C : In this study, the skin friction coefficient is determined for a flat plate using the following equation: where Reynolds number depends on the scale.While this is not an exact method for the determination of the height of the first prism layer, it yields satisfactory results.The obtained y + values are checked, and it is ensured that 30 y + > in numerical simulations where wall functions are applied and that 1 y + < in numerical simulations with the transition model.Special attention is given to the refinement around the propeller and in the MRF zone.The transition from the prism layer to the core mesh is carefully discretized to avoid possible numerical diffusion.A more detailed discussion regarding the influence of y + values on the obtained numerical results regarding the open water test can be found in Owen et al. [15].The frictional velocity u τ is calculated as follows: where the wall shear stress τ w is calculated using the skin friction coefficient C f : In this study, the skin friction coefficient is determined for a flat plate using the following equation: where Reynolds number depends on the scale.While this is not an exact method for the determination of the height of the first prism layer, it yields satisfactory results.The obtained y + values are checked, and it is ensured that y + > 30 in numerical simulations where wall functions are applied and that y + < 1 in numerical simulations with the transition model.Special attention is given to the refinement around the propeller and in the MRF zone.The transition from the prism layer to the core mesh is carefully discretized to avoid possible numerical diffusion.A more detailed discussion regarding the influence of y + values on the obtained numerical results regarding the open water test can be found in Owen et al. [15].

Verification Study
The GCI method, based on the Richardson extrapolation is used for the verification study.The GCI method is used to determine the appropriate grid size by determining the grid uncertainty.If the iterative uncertainty is neglected, then the numerical uncertainty consists only of the grid uncertainty.The interested reader can find more details about the method in [24].

Case Study
In this study, a propeller is modeled using computer-aided design (CAD) software.The modeled propeller has geometric properties that resemble the one used for the Japan CFD Workshop 2015 for the Japan Bulk Carrier (JBC).The propeller is then scaled and the numerical simulations of OWT are conducted.Figure 2 shows the 3D scan of the propeller model and the CAD model used in the numerical simulations.Table 1 contains the propeller main particulars, and the scales used in the CFD simulations are listed within the same table.The advance coefficients are obtained by changing the speed of advance with a constant rate of revolution of the propeller.The rate of revolution for different scales is defined using the following equation: where n s is the rate of revolution at the specific scale and n m is the rate of revolution at the model scale.

Case Study
In this study, a propeller is modeled using computer-aided design (CAD) softwa The modeled propeller has geometric properties that resemble the one used for the Jap CFD Workshop 2015 for the Japan Bulk Carrier (JBC).The propeller is then scaled and t numerical simulations of OWT are conducted.Figure 2 shows the 3D scan of the propel model and the CAD model used in the numerical simulations.Table 1 contains the pr peller main particulars, and the scales used in the CFD simulations are listed within t same table.The advance coefficients are obtained by changing the speed of advance wi a constant rate of revolution of the propeller.The rate of revolution for different scales defined using the following equation:

Verification Study
Firstly, the verification study is performed using the numerical simulations at t model scale with the transition model.Since the numerical simulations are steady sta

Verification Study
Firstly, the verification study is performed using the numerical simulations at the model scale with the transition model.Since the numerical simulations are steady state, only the GCI for the spatial discretization is calculated.Table 2 shows the data of the used grids where the grid spacing h is calculated using the following equation: where N is the total number of finite volume cells and V i is the volume of the i-th cell.The grid refinement ratio is calculated as follows: The GCI is calculated for the open water efficiency η o in the range of advance coefficient from 0.1 to 0.6.Table 3 presents the obtained GCIs with the calculated averages as well.Both the average coarse and fine GCIs are low, and the coarse GCI is under 4 %; thus, the medium grid size is used for the rest of the numerical simulations.Another verification study is conducted for three full-scale grids with non-dimensional wall distance y + > 30.The coarse and fine GCIs are calculated for open water efficiency in the considered range of advance coefficients.Table 4 presents the details about the grids, while Table 5 shows the calculated grid convergence indices for the open water efficiency.This study shows that the average GCIs in the range of advance coefficient from 0.1 to 0.6 are less than 4% and the difference between the coarse and fine GCIs is negligible.Thus, a medium grid size can be used for the full-scale simulations.The grids for the other scales use the same grid setup with varying prism layers to maintain y + > 30, so it is expected that the GCI will not differ significantly from the two studies presented.

Turbulence Models
The influence of the turbulence model on the obtained results is investigated using the model scale and full-scale numerical simulations with the medium grid size and the non-dimensional wall distance y + > 30.Figures 3 and 4 show the open water curves

Turbulence Models
The influence of the turbulence model on the obtained results is investigated the model scale and full-scale numerical simulations with the medium grid size a non-dimensional wall distance 30 y + > .Figures 3 and 4 show the open water cur tained from the model and full-scale numerical simulations, respectively.The influ the turbulence model on the results is barely visible for the full-scale case.The r difference in the open water efficiency for the SSTKO turbulence model is equal to for model scale and 0.65% for full-scale.The transition model is disabled for bot shown in the figures.

Model Scale
The numerical simulations at the model scale are performed for non-dimensional wall distance 0 3 y + > and 1 y + ≤ .The open water curves for the first case are already presented in the previous subsection.Figure 5 shows the open water curves for the numerical simulations at the model scale with and without the transition model for the case with 1 y + ≤ .Table 6 shows the numerical values of the relative errors, with respect to the case with the transition model, at different advance coefficients and the average values as well.
The data shows lower values of the torque coefficient for the case with the transition model enabled, which in turn leads to higher values of the open water efficiency.It can be seen that the transition model influences the torque coefficient more in comparison to the thrust coefficient.

Model Scale
The numerical simulations at the model scale are performed for non-dimensional wall distance y + > 30 and y + ≤ 1.The open water curves for the first case are already presented in the previous subsection.Figure 5 shows the open water curves for the numerical simulations at the model scale with and without the transition model for the case with y + ≤ 1. Table 6 shows the numerical values of the relative errors, with respect to the case with the transition model, at different advance coefficients and the average values as well. well.
The data shows lower values of the torque coefficient for the case with the transition model enabled, which in turn leads to higher values of the open water efficiency.It can be seen that the transition model influences the torque coefficient more in comparison to the thrust coefficient.The data shows lower values of the torque coefficient for the case with the transition model enabled, which in turn leads to higher values of the open water efficiency.It can be seen that the transition model influences the torque coefficient more in comparison to the thrust coefficient.
Figures 6 and 7 show the distribution of the skin friction coefficient obtained from the model scale numerical simulations.Significant differences between the two cases can be noticed.The skin friction coefficient is lower in the case with the transition model, which is expected considering the partially laminar flow.The lower skin friction leads to lower values of the torque coefficient which results in higher open water efficiencies.Figures 6 and 7 show the distribution of the skin friction coefficient obtained from the model scale numerical simulations.Significant differences between the two cases can be noticed.The skin friction coefficient is lower in the case with the transition model, which is expected considering the partially laminar flow.The lower skin friction leads to lower values of the torque coefficient which results in higher open water efficiencies.

Scale Effects
The open water curves obtained from numerical simulations at different scales are compared in this subsection.Figure 8 shows the open water efficiency as a function of the

Scale Effects
The open water curves obtained from numerical simulations at different scales are compared in this subsection.Figure 8 shows the open water efficiency as a function of the advance coefficient obtained from the simulations at different scales.Figures 9 and 10 show the thrust and torque coefficients, respectively.In Figures 8-10, the numerical results at the model scale are extrapolated to full-scale using the ITTC 1978 Performance Prediction Method (PPM).It can be noticed that the differences between the open water efficiencies are more apparent at higher advanced coefficients.The open water efficiency at the full-scale obtained using ITTC 1978 PPM is higher than at the model scale.However, the extrapolated values of open water efficiency are lower than the ones obtained using numerical simulations in full-scale.This can be attributed to the fact that ITTC 1978 PPM considers a rough full-scale propeller, while in this study smooth full-scale propeller is analyzed.
advance coefficient obtained from the simulations at different scales.Figures 9 and 10 show the thrust and torque coefficients, respectively.In Figures 8-10, the numerical results at the model scale are extrapolated to full-scale using the ITTC 1978 Performance Prediction Method (PPM).It can be noticed that the differences between the open water efficiencies are more apparent at higher advanced coefficients.The open water efficiency at the full-scale obtained using ITTC 1978 PPM is higher than at the model scale.However, the extrapolated values of open water efficiency are lower than the ones obtained using numerical simulations in full-scale.This can be attributed to the fact that ITTC 1978 PPM considers a rough full-scale propeller, while in this study smooth full-scale propeller is analyzed.Figure 8 shows that the open water efficiency increases with the decrease in scale.Minor discrepancies between the open water efficiencies are visible in the range of lower advance coefficients.The thrust coefficients decrease with the increase in scale, while the torque coefficients decrease with the decrease in scale.This tendency can be seen over the entire range of advance coefficients.It should be noted that the scale effects on the frictional component of the thrust and torque are significant, while the scale effects on the pressure component of the thrust and torque are relatively low [36].Bhattacharyya et al. [36] noticed that the pressure component has a positive contribution, and the friction component has a negative contribution to the value of propeller thrust at any scale.On the other hand, the absolute contributions from the pressure and friction components to the total torque are positive at any scale.At higher numbers, the portion of frictional components in the total torque and thrust values are lower in comparison to the portion of the frictional components in the total torque and thrust values at lower Re numbers, since the scale effects of the frictional component of the thrust and torque are significant.Since the frictional component has a positive contribution to the total torque, the torque coefficients will be lower at higher Re numbers.On the other hand, since the frictional component has a negative contribution to the total thrust, the thrust coefficients will be higher at higher Re numbers.Figure 8 shows that the open water efficiency increases with the decrease in scale.Minor discrepancies between the open water efficiencies are visible in the range of lower advance coefficients.The thrust coefficients decrease with the increase in scale, while the torque coefficients decrease with the decrease in scale.This tendency can be seen over the entire range of advance coefficients.It should be noted that the scale effects on the frictional component of the thrust and torque are significant, while the scale effects on the pressure component of the thrust and torque are relatively low [36].Bhattacharyya et al. [36] noticed that the pressure component has a positive contribution, and the friction component has a negative contribution to the value of propeller thrust at any scale.On the other hand, the absolute contributions from the pressure and friction components to the total torque are positive at any scale.At higher Re numbers, the portion of frictional components in the total torque and thrust values are lower in comparison to the portion of the frictional components in the total torque and thrust values at lower Re numbers, since the scale effects of the frictional component of the thrust and torque are significant.Since the frictional component has a positive contribution to the total torque, the torque coefficients will be lower at higher Re numbers.On the other hand, since the frictional component has a negative contribution to the total thrust, the thrust coefficients will be higher at higher Re numbers.
Additionally, it is worth noting that the results of model scale numerical simulations Additionally, it is worth noting that the results of model scale numerical simulations have the same non-dimensional wall distance y + > 30 without the transition model.Large differences can be seen between the results obtained from the model scale simulations and the remaining simulations.This may be attributed to the fact that the scales for model and M1 are significantly different, i.e., λ M /λ M1 ≈ 10, and between the other scales the difference is significantly lower.
Table 7 presents the differences between the numerical values obtained for all scales at several advanced coefficients as well as the average values.These differences are calculated using the equation: where φ stands for either K T , K Q , or η o , index x denotes either M1, M2, M3, or F, and index M stands for model scale.The highest average change in open water efficiencies is obtained for full-scale and it is equal to 17.86%.
Figures 11 and 12 show the obtained distribution of the skin friction coefficient at the advance coefficient J = 0.7 on the pressure and suction side of the propeller.The coefficient is calculated using the same density of the fluid, but with different speeds of advance for each case.It is visible that with the decrease in the scale of the propeller, the skin friction coefficient decreases, which is expected since the Reynolds number increases with the decrease in scale.The values of skin friction coefficient near the propeller hub are low with the tendency to in-crease at higher radii.This can be attributed to the fact that the friction velocity at higher radii is significantly higher.It is worth mentioning that the differences in skin friction co-efficients for M3 and F are insignificant.on the pressure and suction side of the propeller.The coe cient is calculated using the same density of the fluid, but with different speeds of advan for each case.It is visible that with the decrease in the scale of the propeller, the skin fr tion coefficient decreases, which is expected since the Reynolds number increases with decrease in scale.The values of skin friction coefficient near the propeller hub are low w the tendency to increase at higher radii.This can be attributed to the fact that the fricti velocity at higher radii is significantly higher.It is worth mentioning that the differen in skin friction coefficients for M3 and F are insignificant.The distributions of the turbulent viscosity ratio (TVR) at 0.75R are presented in Figure 13.TVR is defined as the ratio between turbulent viscosity µ t and dynamic viscosity µ.It is shown that the turbulent viscosity for the model scale is equal to zero, which suggests that the flow is laminar.For other scales, TVR around the blade profile increases with the decrease in scale.It is shown that the flow around the blade is turbulent and that the Reynolds stress increases with the decrease in scale in comparison to viscous shear stress.The distributions of the turbulent viscosity ratio (TVR) at 0.75R are presented in Figure 13.TVR is defined as the ratio between turbulent viscosity t μ and dynamic vis- cosity μ .It is shown that the turbulent viscosity for the model scale is equal to zero, which suggests that the flow is laminar.For other scales, TVR around the blade profile increases with the decrease in scale.It is shown that the flow around the blade is turbulent and that the Reynolds stress increases with the decrease in scale in comparison to viscous shear stress.
Figure 14 shows the open water efficiency for M1, M2, M3, and F propellers as well as for the model scale obtained with the transition model.It can be seen that the open water efficiency increases once the transition model is applied.From this figure, it can be seen that the impact of the scale effect on open water efficiency is significantly lower if the transition model is applied for the model scale simulations.The distributions of the turbulent viscosity ratio (TVR) at 0.75R are presented in Figure 13.TVR is defined as the ratio between turbulent viscosity t μ and dynamic vis- cosity μ .It is shown that the turbulent viscosity for the model scale is equal to zero, which suggests that the flow is laminar.For other scales, TVR around the blade profile increases with the decrease in scale.It is shown that the flow around the blade is turbulent and that the Reynolds stress increases with the decrease in scale in comparison to viscous shear stress.
Figure 14 shows the open water efficiency for M1, M2, M3, and F propellers as well as for the model scale obtained with the transition model.It can be seen that the open water efficiency increases once the transition model is applied.From this figure, it can be seen that the impact of the scale effect on open water efficiency is significantly lower if the transition model is applied for the model scale simulations.

Conclusions
Numerical simulations of the open water test (OWT) are performed at different scales.The simulation setup is described in detail as well as the meshing process.The numerical simulations of the flow around the propeller are carried out using the steadystate moving reference frame (MRF) method.Special attention is given to the grid refine-

Conclusions
Numerical simulations of the open water test (OWT) are performed at different scales.The simulation setup is described in detail well as the meshing process.The numerical simulations of the flow around the propeller are carried out using the steady-state moving reference frame (MRF) method.Special attention is given to the grid refinements around the MRF zone and the area around the propeller to predict the flow more accurately.The shear stress transport k − ω (SSTKO) turbulence model is used to close the system of equations since it can be coupled with the Gamma Reynolds Theta (γ − Re θ ) transition model and it is the best compromise between the accuracy and the required computational time.The nondimensional wall distance y + is kept below 1 for the numerical simulations at the model scale, including the transition model, to obtain more accurate results since the laminar flow is present.Within the numerical simulations for other scales, the non-dimensional wall distance is above 30 and the transition model is disabled.The verification study is performed for spatial discretization using the grid convergence index (GCI) method, which shows that the medium size grid is appropriate in terms of computational time and the accuracy of the results.The open water curves are presented for the numerical simulations at the model scale with the transition model, which is compared to the case without the transition model.The results show that when the transition model is applied, the torque coefficient decreases, and thus the open water efficiency increases, which is also confirmed by the distribution of the skin friction coefficient.The scale effects can be noticed from the obtained open water curves, the distribution of the skin friction, as well as the turbulence viscosity ratio (TVR) field.It can be concluded that the open water efficiency increases with the decrease in scale.Finally, a comparison between the numerical simulations at the model scale with the transition model with the numerical simulations at other scales is given.It should be noted that when the transition model is applied, the scale effects on open water characteristics are significantly lower.

Figure 2 .
Figure 2. The geometry of the stock propeller.Three-dimensional scan (a), CAD model (b).

Figure 2 .
Figure 2. The geometry of the stock propeller.Three-dimensional scan (a), CAD model (b).
model and full-scale numerical simulations, respectively.The influence of the turbulence model on the results is barely visible for the full-scale case.The relative difference in the open water efficiency for the SSTKO turbulence model is equal to 2.83% for model scale and 0.65% for full-scale.The transition model is disabled for both cases shown in the figures.

Figure 3 .
Figure 3.The open water curves of model scale propeller obtained using RKE and SSTKO lence models.

Figure 4 .
Figure 4.The open water curves of full-scale propeller obtained using RKE and SSTKO turbulence models.

Figure 4 .
Figure 4.The open water curves of full-scale propeller obtained using RKE and SSTKO turbulence models.

Figure 5 .
Figure 5. Open water curves for model scale with and without the transition model.

Figure 5 .
Figure 5. Open water curves for model scale with and without the transition model.

Figure 6 .
Figure 6.Distribution of the skin friction coefficient on the suction side obtained from numerical simulations at model scale for 0.7 J = without transition model (left) and with transition model (right).

Figure 6 .
Figure 6.Distribution of the skin friction coefficient on the suction side obtained from numerical simulations at model scale for J = 0.7 without transition model (left) and with transition model (right).

Figure 6 .
Figure 6.Distribution of the skin friction coefficient on the suction side obtained from numerical simulations at model scale for 0.7 J = without transition model (left) and with transition model (right).

Figure 7 .
Figure 7. Distribution of the skin friction coefficient on the pressure side obtained from numerical simulations at model scale for 0.7 J = without transition model (left) and with transition model enabled (right).

Figure 7 .
Figure 7. Distribution of the skin friction coefficient on the pressure side obtained from numerical simulations at model scale for J = 0.7 without transition model (left) and with transition model enabled (right).

Figure 8 .
Figure 8. Open water efficiency as a function of advance coefficient for different scales.Figure 8. Open water efficiency as a function of advance coefficient for different scales.

Figure 8 .
Figure 8. Open water efficiency as a function of advance coefficient for different scales.Figure 8. Open water efficiency as a function of advance coefficient for different scales.

Figure 8 .
Figure 8. Open water efficiency as a function of advance coefficient for different scales.

Figure 9 .
Figure 9. Thrust coefficient as a function of advance coefficient for different scales.Figure 9. Thrust coefficient as a function of advance coefficient for different scales.

Figure 9 .
Figure 9. Thrust coefficient as a function of advance coefficient for different scales.Figure 9. Thrust coefficient as a function of advance coefficient for different scales.

Figure 10 .
Figure 10.Torque coefficient as a function of advance coefficients for different scales.

Figure 10 .
Figure 10.Torque coefficient as a function of advance coefficients for different scales.

Figure 14 18 Figure 14 .
Figure 14 shows the open water efficiency for M1, M2, M3, and F propellers as well as for the model scale obtained with the transition model.It can be seen that the open water efficiency increases once the transition model is applied.From this figure, it can be seen that the impact of the scale effect on open water efficiency is significantly lower if the tran-sition model is applied for the model scale simulations.J. Mar.Sci.Eng.2022, 10, 1132 16 of 18

Figure 14 .
Figure 14.The obtained open water efficiencies.

Table 1 .
The main particulars of the considered propeller in the different scales.

Table 1 .
The main particulars of the considered propeller in the different scales.

Table 2 .
Number of cells, grid spacing, and grid refinement ratio for model scale numerical simulations with the transition model.

Table 3 .
Fine and coarse GCIs for the range of advance coefficients and their average for model scale.

Table 4 .
Number of cells, grid spacing, and grid refinement ratio for full-scale numerical simulations.

Table 5 .
Fine and coarse GCI for the range of advance coefficients and their average for full-scale.

Table 6 .
Relative differences between the thrust and torque coefficients and open water efficiencies in the range of advance coefficients.

Table 6 .
Relative differences between the thrust and torque coefficients and open water efficiencies in the range of advance coefficients.

Table 7 .
The change in open water characteristics between the model scale and other scales.

Table 7 .
The change in open water characteristics between the model scale and other scales.
o η , % Figures 11 and 12 show the obtained distribution of the skin friction coefficient at advance coefficient