Optimization of Processing Parameters to Increase Thermal Conductivity of Rice Straw Fiber Film

: Biodegradable mulching ﬁlm (BMF) is a promising alternative to petroleum-based plastic mulching ﬁlm. Thermal conductivity is an important quality factor of BMF that a ﬀ ects the heat transfer between ambient to soil and plant growth. The objective of this research was to enhance the thermal conductivity of ﬁber ﬁlm through an environmentally friendly agent and optimized processing conditions. Response surface methodology (RSM) was used to optimize the processing conditions. With optimized process conditions of 70 g / m 2 basis weight, 1.5% wet strength agent content, 0.5% neutral sizing agent content, 15% charcoal addition ratio, and 55 ◦ SR beating degree, the ﬁlms showed satisfactory thermal conductivity (0.0714 W / m · K) and high dry and wet tensile strengths (33.4 and 12.2 N). The addition of charcoal increased the thermal conductivity of the ﬁlm by 34.31%. This promising result shows the biodegradable ﬁber ﬁlm is able to increase soil temperature and meet the required temperature for crop growth.


Introduction
Plastic mulching film (PMF) has been widely used in modern intensive farming in order to inhibit weed growth, increase soil temperature, reduce water evaporation, control the leaching of crop nutrients, and increase the yield [1,2]. About one million tons of petroleum-based PMF is consumed annually in the farmlands of China [3,4]. However, petroleum-based PMF is not easily degraded in farmland, and its bio-degradation rate is very low even after years of exposure to soil microbial communities [5][6][7]. Furthermore, wind and rain erosion often cause the entire film to break into small pieces, thus making the recycling very difficult and time-consuming [8,9]. Ultimately, most plastic residues are commonly left in the field or burned by farmers, which leads to serious environmental pollution. Biodegradable materials mainly include biodegradable ceramics and biodegradable plastics [10,11]. To address this issue, the development of a biodegradable film with desired properties for both plant growth and environmental impact has become a research focus [12][13][14].
Biodegradable mulching film (BMF) is a promising alternative to petroleum-based PMF. At present, the degradable film can be mainly divided into photo-degradable, biodegradable, photo-biodegradable mulching, and plant fiber films [15][16][17]. Although some progress has been made in the first three degradable films, they are mainly synthesized by the co-polymerization of starch and other nutrients with degradable organic compounds. The adoption of these films is always favorable due to high costs, incomplete degradation, etc. To overcome this issue, researchers have developed plant fiber films derived from plant raw materials, such as softwood, hardwood, hemp, reed, waste cotton,

Materials
Rice straw fiber used as raw material was produced by a D200 straw fiber extruder with particle size under 10 mm and an average aspect ratio of 22.8 to 58.3 [35]. Kraft pulp (KP) wood fiber with 27% moisture content (wb) was used for the framework to maintain mechanical strength. The wet strength agent used for tensile strength improvement was purchased from Xinghuo Chemical Plant (Mudanjiang, China). Polyamide polyamine epichlorohydrin resin (PPE) which was a water-soluble, cationic, thermosetting resin was used as a wet strength agent. The neutral sizing agent used for hydrophobicity enhancement was purchased from Jinhao Chemical Plant (Qingzhou, China). Alkyl ketene dimer (AKD) which was obtained by emulsifying stearoyl chloride and triethylamine hydrochloride was used as a neutral sizing agent. Charcoal obtained with particle size less than 0.12 mm, the thermal conductivity of 129 W/m·K from Tianjin Ebory Chemical Industry Co., Ltd. (Tianjin, China) was used for improving the thermal conductivity. All of these chemicals are laboratory level and triple distilled water was used for all solutions.

Preparation of Fiber Film
Rice straw fiber and KP wood fiber were beaten to form pulps with designed beating degrees. The beating degree was determined by a ZTG-100 pulp degree test machine (Yueming Small Test Machine Co., Ltd., Changchun, China) following Chinese Standard QB/T 24325 (2009). Charcoal, wet strength agent, and neutral sizing agent were added to the pulp and homogeneously mixed. The film samples were prepared following Chinese Standard QB/T 24324 (2009). Film samples were dried by a Appl. Sci. 2019, 9, 4645 3 of 12 film dryer at a vacuum pressure above 96 kPa, temperature about 97 • C, and drying time 5-7 min. Drying film samples were conditioned at room temperature (23 ± 1 • C) and 50% ± 2% relative humidity for at least 24 h before testing. Figure 1 was the schematic illustration of manufacturing the BMF. Dry tension strength and wet tension strength was tested by a ZL-300 pendulum paper tensile strength test machine (Yueming Small Test Machine Co., Ltd., Changchun, China) according to Chinese Standard GB/T 12914 (2008) and GB/T 465. 2 (2008), and thermal conductivity was measured by a DRL-III thermal conductivity tester (Xiangtan Xiangyi Apparatus Co., Ltd., Hunan, China) according to ASTM D 5470 (2006).

Preparation of Fiber Film
Rice straw fiber and KP wood fiber were beaten to form pulps with designed beating degrees. The beating degree was determined by a ZTG-100 pulp degree test machine (Yueming Small Test Machine Co., Ltd., Changchun, China) following Chinese Standard QB/T 24325 (2009). Charcoal, wet strength agent, and neutral sizing agent were added to the pulp and homogeneously mixed. The film samples were prepared following Chinese Standard QB/T 24324 (2009). Film samples were dried by a film dryer at a vacuum pressure above 96 kPa, temperature about 97 °C, and drying time 5-7 min. Drying film samples were conditioned at room temperature (23 ± 1 °C) and 50% ± 2% relative humidity for at least 24 h before testing. Figure 1 was the schematic illustration of manufacturing the BMF. Dry tension strength and wet tension strength was tested by a ZL-300 pendulum paper tensile strength test machine (Yueming Small Test Machine Co., Ltd., Changchun, China) according to Chinese Standard GB/T 12914 (2008) and GB/T 465. 2 (2008), and thermal conductivity was measured by a DRL-III thermal conductivity tester (Xiangtan Xiangyi Apparatus Co., Ltd., Hunan, China) according to ASTM D 5470 (2006).

Experimental Design
Initially, preliminary experiments were conducted following a single factorial method to identify the major processing parameters affecting the performance of the fiber film and to find out the optimal ranges. Five processing parameters including basis weight (g/m 2 ), neutral sizing agent content (%), charcoal addition ratio (%), wet strength agent content (%), and beating degree (°SR) were selected based on the single factorial method.
The central composite design approach was used to study the effects and interaction of basis weight, neutral sizing agent content, charcoal addition ratio, wet strength agent content, and beating degree on dry and wet tensile strengths and thermal conductivity of rice straw fiber films. The central composite design is a type of response surface methodology (RSM). RSM is a general linear model in which attention is focused on characteristics of the fit response function; in particular, where optimum estimate response values occur. There were five levels of basis weight (50 to 70 g/m 2 ), neutral sizing agent content (0.5% to 0.9%), charcoal addition ratio (0% to 20%), wet strength agent content (0.8% to 1.6%), and beating degree (35 to 55 °SR). The ranges and levels of independent variables are shown in Table 1. Table 1. Central composite design for five variables at five levels.

Experimental Design
Initially, preliminary experiments were conducted following a single factorial method to identify the major processing parameters affecting the performance of the fiber film and to find out the optimal ranges. Five processing parameters including basis weight (g/m 2 ), neutral sizing agent content (%), charcoal addition ratio (%), wet strength agent content (%), and beating degree ( • SR) were selected based on the single factorial method.
The central composite design approach was used to study the effects and interaction of basis weight, neutral sizing agent content, charcoal addition ratio, wet strength agent content, and beating degree on dry and wet tensile strengths and thermal conductivity of rice straw fiber films. The central composite design is a type of response surface methodology (RSM). RSM is a general linear model in which attention is focused on characteristics of the fit response function; in particular, where optimum estimate response values occur. There were five levels of basis weight (50 to 70 g/m 2 ), neutral sizing agent content (0.5% to 0.9%), charcoal addition ratio (0% to 20%), wet strength agent content (0.8% to 1.6%), and beating degree (35 to 55 • SR). The ranges and levels of independent variables are shown in Table 1.

Regression Models
RSM, which combines mathematics and statistics together, is usually used to analyze the relative significance of different operating parameters even in complicated systems [39][40][41][42]. Therefore, this method was used to optimize the parameters used in this study. The central composite design was Appl. Sci. 2019, 9,4645 5 of 12 adopted to optimize the process to enhance the thermal conductivity of film made by charcoal and rice straw.
Thirty-six experiments were carried out to study the effects and interactions of basis weight, neutral sizing agent content, charcoal addition ratio, wet strength agent content, and beating degree on dry and wet tensile strengths and thermal conductivity of films. These are represented in Table 2. Table 2 also shows the values of dry tensile strength, wet tensile strength, and thermal conductivity at each experimental designed condition.
The regression model results indicated that the best models are the quadratic model for dry and wet tensile strengths, and a linear model for thermal conductivity. Table 3 shows the significance of the regression model parameters. The R 2 for dry and wet tensile strengths and thermal conductivity models are 0.901, 0.873, and 0.781, respectively. The p values are all less than 0.001 showing that the models are highly significant, and there is only a 0.01%, 0.01%, and 0.1% chance of occurrence of model f value because of noise. The lack of fit was not significant with p values larger than 0.05 for all three models. The three model equations are shown as Equations (2)-(4).

Interactive Effects on Dry Tensile Strength
The combined effect of basis weight and wet strength agent on dry tensile strength of the BMF with others staying constant (0.7% neutral sizing agent, 10% charcoal addition ratio, and 45 • SR beating degree) is shown in Figure 2a. The dry tensile strength increased as basis weight increased, however, the increase was not significant at low wet strength agent content. This is mainly because the dry tensile strength of the BMF was proportional to the fibers per unit area of the sample. Dry tensile strength also increased as wet strength agent content improved. Wet strength agent in the BMF not just forms a covalent bond with carboxyl of fiber, but enhances the network structure of the BMF through the self-bridging reactions within the wet strength agent and between the wet strength agent and fibers, thus wet strength agent has the function to increase the dry tensile strength [43]. Figure 2a also shows that the interaction of basis weight and wet strength agent content had a significant effect on dry tensile strength. Dry tensile strength reached the highest at 70 g/m 2 basis weight and 1.6% wet strength agent content.

Interactive Effects on Wet Tensile Strength
The combined effect of basis weight and wet strength agent content on wet tensile strength of the BMF with others staying constant (0.7% neutral sizing agent content, 10% charcoal addition ratio, and 45 °SR beating degree) is shown in Figure 3a. Both wet strength agent content and basis weight had significant effects on wet tensile strength. Wet tensile strength increased as both wet strength agent content and basis weight improved, especially at large wet strength content and high basis weight. This is mainly because the increase of the fiber number of the BMF enhanced the bonding ability between the fibers and resulted in increasing wet tensile strength. Meanwhile, the wet strength agent was acting as resin for enhancing the fiber networks through forming a strong crosslink with fibers, thus improving wet tensile strength. Figure 3a also shows the interaction of wet strength agent and basis weight had a significant effect on wet tensile strength. The largest wet tensile strength was attained at 70 g/m 2 basis weight and 1.6% wet strength agent content.
The combined effect of basis weight and beating degree on wet tensile strength of the BMF with others staying constant (0.7% neutral sizing agent content, 10% charcoal addition ratio, and 1.2% wet strength agent content) is shown in Figure 3b. Wet tensile strength decreased slightly with the increase of beating degree when basis weight lower than 60 g/m 2 . This is mainly because the overbeating degree shortened the fiber and weakened the strength of the single fiber, thus wet tensile strength declined. Wet tensile strength increased as the beating degree improved at 60 to 70 g/m 2 basis weight. The continuous increase of basis weight enhanced the number of fibers unit area and enhanced the binding force among the fibers, thus improving wet tensile strength [45,46]. The highest wet tensile strength appeared at 70 g/m 2 basis weight and 55 °SR beating degree. Figure 3c shows the combined effect of neutral sizing agent content and beating degree on wet tensile strength of the BMF with other parameters remaining constant (60 g/m 2 basis weight, 10% charcoal addition ration, and 1.2% wet strength agent content). At low neutral sizing agent content and beating degree, there was a tiny improvement in wet tensile strength as beating degree and neutral sizing agent content improved. But at large neutral sizing agent content and beating degree, wet tensile strength decreased significantly as beating degree and neutral sizing agent content The combined effect of basis weight and beating degree on dry tensile strength of the BMF with others staying constant (0.7% neutral sizing agent content, 10% charcoal addition ratio, and 1.2% wet strength agent) is shown in Figure 2b. Dry tensile strength improved initially when basis weight increased from 50 to 60 g/m 2 and then decreased slightly when the basis weight increased from 60 to 70 g/m 2 at a low beating degree. At a low beating degree, even the addition ration keeps constant, the charcoal content increased as basis weight increased. The increase in charcoal reduces the binding force between fiber and fiber. Therefore, dry tensile strength decreased at a high basis weight. However, at a high beating degree, dry tensile strength increased as basis weight increased. This is mainly due to when at a high beating degree, the hydrogen bonds on the fiber surface and the bond strength between the fibers increased. The result also indicates that the effects of basis weight on dry tensile strength were greater than that of beating degree based on ANOVA analysis. The interaction of basis weight and beating degree also had significant effect on dry tensile strength. Dry tensile strength reached the highest at 70 g/m 2 basis weight and 55 • SR beating degree.
The combined effect of neutral sizing agent content and charcoal addition ratio on dry tensile strength of the BMF with other parameters remaining constant (60 g/m 2 basis weight, 1.2% wet strength agent content, and 45 • SR beating degree) is shown in Figure 2c. It was observed that at low charcoal addition ratio, dry tensile strength decreased as neutral sizing agent content improved. This is probably because the physical adsorption occurred between the cationic charges of neutral sizing agent and the anionic charges of pulp fiber. The formation of low polymer components (or discrete fragments) in the neutral sizing agent led to the uneven distribution of charges on the fiber surface and the localized cation patching points, thus causing the decrease in dry tensile strength. At a high charcoal addition ratio, dry tensile strength increased as neutral sizing agent content improved. Neutral sizing agent ester with cellulose. The neutral sizing agent acted as an adhesive on the surface of the fibers forming a strong hydrogen bond, which increased the binding force among pulp fibers and enhanced dry tensile strength [44]. According to Figure 2c, the effect of charcoal addition ratio on dry tensile strength was a Appl. Sci. 2019, 9, 4645 7 of 12 little stronger than that of neutral sizing agent content based on an ANOVA analysis. The maximum dry tensile strength value appeared at 0.6% neutral sizing agent content and 7% charcoal addition ratio.

Interactive Effects on Wet Tensile Strength
The combined effect of basis weight and wet strength agent content on wet tensile strength of the BMF with others staying constant (0.7% neutral sizing agent content, 10% charcoal addition ratio, and 45 • SR beating degree) is shown in Figure 3a. Both wet strength agent content and basis weight had significant effects on wet tensile strength. Wet tensile strength increased as both wet strength agent content and basis weight improved, especially at large wet strength content and high basis weight. This is mainly because the increase of the fiber number of the BMF enhanced the bonding ability between the fibers and resulted in increasing wet tensile strength. Meanwhile, the wet strength agent was acting as resin for enhancing the fiber networks through forming a strong crosslink with fibers, thus improving wet tensile strength. Figure 3a also shows the interaction of wet strength agent and basis weight had a significant effect on wet tensile strength. The largest wet tensile strength was attained at 70 g/m 2 basis weight and 1.6% wet strength agent content.
The combined effect of basis weight and beating degree on wet tensile strength of the BMF with others staying constant (0.7% neutral sizing agent content, 10% charcoal addition ratio, and 1.2% wet strength agent content) is shown in Figure 3b. Wet tensile strength decreased slightly with the increase of beating degree when basis weight lower than 60 g/m 2 . This is mainly because the overbeating degree shortened the fiber and weakened the strength of the single fiber, thus wet tensile strength declined. Wet tensile strength increased as the beating degree improved at 60 to 70 g/m 2 basis weight. The continuous increase of basis weight enhanced the number of fibers unit area and enhanced the binding force among the fibers, thus improving wet tensile strength [45,46]. The highest wet tensile strength appeared at 70 g/m 2 basis weight and 55 • SR beating degree. Figure 3c shows the combined effect of neutral sizing agent content and beating degree on wet tensile strength of the BMF with other parameters remaining constant (60 g/m 2 basis weight, 10% charcoal addition ration, and 1.2% wet strength agent content). At low neutral sizing agent content and beating degree, there was a tiny improvement in wet tensile strength as beating degree and neutral sizing agent content improved. But at large neutral sizing agent content and beating degree, wet tensile strength decreased significantly as beating degree and neutral sizing agent content improved. This may be because of the following reasons. The neutral sizing agent readily reacted with the fibers to form ketene ester derivatives on the surface of the fiber. Meanwhile, the exposure of the internal hydrophobic group (long chain alkyl group) to the surface of fibers increased the hydrophobic properties of the fiber, thus enhancing the wet tensile strength at low neutral sizing agent content. When the neutral sizing agent increased to the high level, the emulsion particles became larger and the dispersion capability became weaker, thus the wet tensile strength decreased. The sizing effect reduced, thus decreasing wet tensile strength accordingly. According to Figure 3c, the effect of beating degree on wet tensile strength was a little stronger than that of neutral sizing agent content. The largest wet tensile strength appeared at 0.5% neutral sizing agent content and 55 • SR beating degree. Figure 3d shows the combined effect of charcoal addition ratio and wet strength agent content on wet tensile strength of the BMF with others staying constant (60 g/m 2 basis weight, 0.7% neutral sizing agent content, and 45 • SR beating degree). Wet tensile strength enhanced uncommonly as wet strength agent content improved at low charcoal addition ratio from 0% to 10%. The chemical crosslink formed by the mutual reaction of the functional group of wet strength agent itself can generate an interlaced chain network structure around the fibers. The chemical crosslink with strong hydrophobic function prevented the water absorption and expansion of the hemicelluloses, thus the wet tensile strength increased. At a high charcoal addition ratio, the wet strength agent content did not show a significant effect on wet tensile strength. This is likely because, at a high charcoal addition ratio, the anionic charges of fiber and the cationic charges of wet strength agent reached to equal, thus the effect of wet tensile strength on wet tensile strength was not significant [47,48]. On the basis of Figure 3d, the effect of wet strength agent content on wet tensile strength was greater than that of charcoal addition ratio. The largest wet tensile strength appeared at a 6% charcoal addition ratio and 1.6% wet strength agent content.
crosslink formed by the mutual reaction of the functional group of wet strength agent itself can generate an interlaced chain network structure around the fibers. The chemical crosslink with strong hydrophobic function prevented the water absorption and expansion of the hemicelluloses, thus the wet tensile strength increased. At a high charcoal addition ratio, the wet strength agent content did not show a significant effect on wet tensile strength. This is likely because, at a high charcoal addition ratio, the anionic charges of fiber and the cationic charges of wet strength agent reached to equal, thus the effect of wet tensile strength on wet tensile strength was not significant [47,48]. On the basis of Figure 3d, the effect of wet strength agent content on wet tensile strength was greater than that of charcoal addition ratio. The largest wet tensile strength appeared at a 6% charcoal addition ratio and 1.6% wet strength agent content.

Effects on Thermal Conductivity
The regression model showed the linear relationship between the thermal conductivity and processing parameters (Equation 4). Figure 4 shows the detailed effect of those processing parameters on the thermal conductivity. Thermal conductivity was positively correlated with basis weight (Figure 4a), charcoal addition ratio (Figure 4c), wet strength agent content (Figure 4d), and beating degree (Figure 4e), but negatively correlated with neutral sizing agent content (Figure 4b).
It was found that the charcoal addition ratio was the most influential factor on thermal conductivity (Figure 4c). The highest thermal conductivity was 0.0733 W/m·K, which was achieved at the highest charcoal addition ratio (20%). Through the direct contact and tunnel effect, thermal conductivity was enhanced between the charcoal particles and fibers, thus improving the thermal conductivity of the whole film. Because of the existence of the fiber and charcoal particles, there were

Effects on Thermal Conductivity
The regression model showed the linear relationship between the thermal conductivity and processing parameters (Equation (4)). Figure 4 shows the detailed effect of those processing parameters on the thermal conductivity. Thermal conductivity was positively correlated with basis weight (Figure 4a), charcoal addition ratio (Figure 4c), wet strength agent content (Figure 4d), and beating degree (Figure 4e), but negatively correlated with neutral sizing agent content (Figure 4b).
degree (Figure 4e), but negatively correlated with neutral sizing agent content (Figure 4b). was found that the charcoal addition ratio was the most influential factor on thermal conductivity (Figure 4c). The highest thermal conductivity was 0.0733 W/m·K, which was achieved at the highest charcoal addition ratio (20%). Through the direct contact and tunnel effect, thermal conductivity was enhanced between the charcoal particles and fibers, thus improving the thermal conductivity of the whole film. Because of the existence of the fiber and charcoal particles, there were two types of

Optimization Analysis
The BMF with desired wet tensile strength, dry tensile strength, and thermal conductivity was obtained by optimized formulations and processing conditions. Due to the design model, the restrictions as previously required, and graphic optimization with the DX 6, the optimum conditions are basis weight 66 to 70 g/m 2 , wet strength agent content 1.4% to 1.6%, neutral sizing agent content 0.5%, charcoal addition ratio 15%, and beating degree 55 °SR (Figure 5). At the optimum condition, dry and wet tensile strengths are larger than 32 N and 11 N, and thermal conductivity is larger than 0.0700 W/m·K.  It was found that the charcoal addition ratio was the most influential factor on thermal conductivity (Figure 4c). The highest thermal conductivity was 0.0733 W/m·K, which was achieved at the highest charcoal addition ratio (20%). Through the direct contact and tunnel effect, thermal conductivity was enhanced between the charcoal particles and fibers, thus improving the thermal conductivity of the whole film. Because of the existence of the fiber and charcoal particles, there were two types of thermal conductivities in the BMF. The first type is remote thermal conductivity formed by the mutual bonding of the fibers with a contact network path. The second type is short-range thermal conductivity formed by charcoal particles with the function of a bridging effect between the fibers [49,50]. Therefore, the thermal conductivity of the BMF was improved.

Optimization Analysis
The BMF with desired wet tensile strength, dry tensile strength, and thermal conductivity was obtained by optimized formulations and processing conditions. Due to the design model, the restrictions as previously required, and graphic optimization with the DX 6, the optimum conditions are basis weight 66 to 70 g/m 2 , wet strength agent content 1.4% to 1.6%, neutral sizing agent content 0.5%, charcoal addition ratio 15%, and beating degree 55 • SR (Figure 5). At the optimum condition, dry and wet tensile strengths are larger than 32 N and 11 N, and thermal conductivity is larger than 0.0700 W/m·K. obtained by optimized formulations and processing conditions. Due to the design model, the restrictions as previously required, and graphic optimization with the DX 6, the optimum conditions are basis weight 66 to 70 g/m 2 , wet strength agent content 1.4% to 1.6%, neutral sizing agent content 0.5%, charcoal addition ratio 15%, and beating degree 55 °SR (Figure 5). At the optimum condition, dry and wet tensile strengths are larger than 32 N and 11 N, and thermal conductivity is larger than 0.0700 W/m·K.

Model Validation
The optimum model was validated by manufacturing the BMF at basis weight 70 g/m 2 , wet strength agent content 1.5%, neutral sizing agent content 0.5%, charcoal addition ratio 15%, and beating degree 55 °SR. Dry tensile strength, wet tensile strength, and thermal conductivity obtained from the validation experiment were 33.4 N, 12.2 N, and 0.0714 W/m·K, respectively, which were

Model Validation
The optimum model was validated by manufacturing the BMF at basis weight 70 g/m 2 , wet strength agent content 1.5%, neutral sizing agent content 0.5%, charcoal addition ratio 15%, and beating degree 55 • SR. Dry tensile strength, wet tensile strength, and thermal conductivity obtained from the validation experiment were 33.4 N, 12.2 N, and 0.0714 W/m·K, respectively, which were highly consistent with the predicted results (dry and wet tensile strengths larger than 32 N and 11N, and thermal conductivity larger than 0.0700 W/m·K). Hence, the optimum condition obtained from RSM design was reliable and applicable, and it indicates that RSM is a powerful tool for system optimization.

Conclusions
The addition of charcoal into rice straw fiber enhanced the thermal conductivity of BMF. The addition of charcoal increased the thermal conductivity of the film by 34.31% from 0.0469 to 0.0714 W/m·K. With optimum conditions (basis weight 70 g/m 2 , wet strength agent content 1.5%, neutral sizing agent content 0.5%, charcoal addition ratio 15%, and beating degree 55 • SR), the high dry tension strength (33.4 N) and high wet tension strength (12.2 N) were also achieved. In addition, the mechanical character of film also meets the agricultural requirements for plant growth. It is believed that the knowledge obtained from this research would be helpful to further improve the performance of plant fiber film.