Biological Effects of High-Voltage Electric Field Treatment of Naked Oat Seeds

In order to study the mechanism of high-voltage electric field (HVEF) biotechnology, corona discharge produced by a multi-needle-plate HVEF was used to treat naked oat seeds, each treatment dose was divided into two groups, one group was covered with a petri dish cover, the other group was directly exposed to HVEF without a petri dish cover. The scanning electron microscope (SEM) results show that the etching degree of the uncovered group was more serious than that of the covered group, it indicates that ion wind etching has a greater impact on the micro-morphology of seed coat, being covered can effectively reduce the etching degree of discharge plasma on seed. Fourier Transform infrared spectroscopy (FTIR) of the seed coat shows most of the HVEF treatment group can form a new absorption peak at 1740 cm−1, which is closely related to the hydrophilicity of the seed. Comprehensive analysis shows that HVEF treatment can improve the hydrophilicity of seeds, whether they are covered or not. Being covered can reduce the degree of etching of the seed coat, but increase the hydrophilicity of the seed, indicating that the non-uniform electric field has a greater impact on the hydrophilicity of the seed. Our study showed that ion wind had an effect on the micro-morphology of seeds, but this effect didn’t translate into a macroscopic effect. This study provides ideas and experimental data support for the study of the biotechnological mechanism of HVEF.


Introduction
The naked oat is a kind of grain-grass-type crop that is cold-loving, drought-resistant and with a strong barren resistance, and it has the highest protein content in cereal grains and is a health-care grain crop [1]. It plays an important role in improving people's diet and ecological construction of agriculture and animal husbandry. With the improvement of people's living standards, the food demand brought about by the rapid increase in population has been increasing, the animal husbandry industry has developed rapidly, the demand for forage has soared and the shortage of forage is more obvious. China's main naked oat producing areas are combined with semi-agricultural and semi-pastoral areas to breed drought-resistant, barren-resistant, high-yield and high-quality varieties. This is more important as a new naked oat variety is being used for both grain and grass. Therefore, it is very important to study the biological effects of high-voltage electric field (HVEF) on naked oat seeds to improve the quality and yield of naked oat.
Multi-needle-plate HVEF is a non-uniform electric field which can produce corona discharge. Multi-needle-plate HVEF is commonly used in the food thawing and drying industry. Researchers have Figure 1. High-voltage electric field (HVEF) device. Note: A is the ultra-clean workbench; B is the electrode system; C is the control unit; D is the high-voltage power supply; E is the high voltage insulation tube.

Floating Rate and Water Absorption Test
The treated seeds were accurately weighed and marked with one ten thousandth of an electronic balance, and 40 mL of deionized water was added into the petri dish to count the number of seeds floating in each group. After soaking for 20 h, the surface moisture of the seed was dried with filter paper and the seed was weighed after water absorption. The floating rate (FR%) and water absorption rate (WAR%) are calculated by the following equations: where Nf is the number of seeds floating in the water, Ns is the number of total soaked seeds, M0 is the weight of the seed before water absorption, M1 is the weight of the seed after water absorption.

Seed Height and Fresh Weight Test
The seeds were placed in a petri dish containing three layers of filter paper, and distilled water was added to each dish every other day to keep the water sufficient. The seeds were placed in a light incubator at a constant temperature of 26 °C. After the seeds were germinated, the light incubator was irradiated with 140 Lux light, continuous illumination for 14 h and darkness for 10 h. In each petri dish, 15 seedlings were randomly selected to measure seedling height and fresh weight after 10 days.

Ion Wind Speed Test
The ion wind speed under different experimental conditions was measured using a thermal anemometer probe (405i, Ruice Electronics Technology Co., Ltd., Guangzhou, China). Each experiment was repeated three times independently and averaged. High-voltage electric field (HVEF) device. Note: A is the ultra-clean workbench; B is the electrode system; C is the control unit; D is the high-voltage power supply; E is the high voltage insulation tube.

Floating Rate and Water Absorption Test
The treated seeds were accurately weighed and marked with one ten thousandth of an electronic balance, and 40 mL of deionized water was added into the petri dish to count the number of seeds floating in each group. After soaking for 20 h, the surface moisture of the seed was dried with filter paper and the seed was weighed after water absorption. The floating rate (FR%) and water absorption rate (WAR%) are calculated by the following equations: where N f is the number of seeds floating in the water, N s is the number of total soaked seeds, M 0 is the weight of the seed before water absorption, M 1 is the weight of the seed after water absorption.

Seed Height and Fresh Weight Test
The seeds were placed in a petri dish containing three layers of filter paper, and distilled water was added to each dish every other day to keep the water sufficient. The seeds were placed in a light incubator at a constant temperature of 26 • C. After the seeds were germinated, the light incubator was irradiated with 140 Lux light, continuous illumination for 14 h and darkness for 10 h. In each petri dish, 15 seedlings were randomly selected to measure seedling height and fresh weight after 10 days.

Ion Wind Speed Test
The ion wind speed under different experimental conditions was measured using a thermal anemometer probe (405i, Ruice Electronics Technology Co., Ltd., Guangzhou, China). Each experiment was repeated three times independently and averaged.

Infrared Spectroscopy Test
The dried seed coat was ground into a powder using an agate mortar, and the sample powder and the potassium bromide were uniformly mixed at a ratio of 1:500 and filtered with 80 target quasi-sieves. The powder was pressed into the disk using a tablet machine (HY-12, Tianguang Spectrometer Co., Ltd., Tianjin, China). Samples were scanned using a Fourier transform infrared spectrometer (Nicolet iS10, Thermo Nicolet Corporation, Madison, WI, USA).

Scanning Electron Microscopy Test
The sample to be observed was sprayed with a metal film and then adhered to the sample stage with conductive double-sided tape. The seed coat of the electric field treatment surface was observed and photographed by scanning electron microscope (S3400, Hitachi Corporation, Tokyo, Japan).

Seedling ROS Content Test
From the same treated seedlings, 3 g was randomly selected on the third and seventh day of inoculation, and the ROS was measured after the ice bath was ground. The substrate used for the assay was 2 ,7 -Dichlorodihydrofluorescein diacetate. The sample to be tested was reacted with 10 mM CM-H2DCFDA at 25 • C for 30 min in the dark according to the method of Babu et al. [21]. The sample was then placed in a 96-well plate containing 100 µL of distilled water in the dark, then put into a microplate reader (SPECTRAMAX I3, Molecular Devices(MD) Corporation, USA). The excitation intensity of 530 nm was detected by excitation with an excitation light of 485 nm. This was repeated six times or more.

Statistical Analysis
All treatments were repeated at least three times. Data from this study were recorded as the mean value ± standard deviation. The SPSS statistical software (Version 16.0) and one-way analysis of variance (ANOVA) were used to analyze the difference of data, and p < 0.05 was considered as a significant difference.

Effect of HVEF on Water Absorption and Hydrophilicity of Naked Oat Seeds
The water absorption of naked oat seeds after treatment with HVEF is shown in Figure 2. It can be seen that the water absorption rate of seeds with or without covered treatment increased when the voltage was 4 kV, 12 kV, 16 kV and 20 kV. However, when the voltage was 8 kV, the water absorption rate decreased. As a whole, except for the 8 kV uncovered treatment group, the water absorption of the other treatment groups was improved by different degrees compared to the control group, and the water absorption rate of the covered group increased under each voltage. The hydrophilicity of the seed during soaking was as shown in Figure 3. It can be seen that the hydrophilicity of the seed increased with or without covered treatment compared with the control group. As can be seen from Figure 4, the floating rate of seeds after covered treatment was significantly lower than that of the control group. Moreover, compared with the uncovered treatment, the floating rate of seeds after covered treatment was reduced, indicating that the covered treatment can better improve the hydrophilicity of seeds.     . Changes in the floating rate of naked oat seeds after HVEF treatment (Different letters indicate statistically significant differences between treatments (p < 0.05)).

Effect of HVEF on the Growth of Naked Oat Seedlings
The seedling height and fresh weight of naked oat seedlings after HVEF treatment are shown in Figures 5 and 6, respectively. After HVEF treatment, the seedling height of naked oat seedlings increased by different degrees with or without a cover, and the fresh weight of seedlings also showed an upward trend with the increase of voltage. However, the effect of ion wind on seedling growth is not significant.

Effect of HVEF on the Growth of Naked Oat Seedlings
The seedling height and fresh weight of naked oat seedlings after HVEF treatment are shown in Figures 5 and 6, respectively. After HVEF treatment, the seedling height of naked oat seedlings increased by different degrees with or without a cover, and the fresh weight of seedlings also showed an upward trend with the increase of voltage. However, the effect of ion wind on seedling growth is not significant. . Changes in the floating rate of naked oat seeds after HVEF treatment (Different letters indicate statistically significant differences between treatments (p < 0.05)).

Effect of HVEF on the Growth of Naked Oat Seedlings
The seedling height and fresh weight of naked oat seedlings after HVEF treatment are shown in Figures 5 and 6, respectively. After HVEF treatment, the seedling height of naked oat seedlings increased by different degrees with or without a cover, and the fresh weight of seedlings also showed an upward trend with the increase of voltage. However, the effect of ion wind on seedling growth is not significant.   Figure 7 shows the ion wind speed treated by HVEF under different voltages. It can be seen from the figure that there is a linear relationship between the ion wind speed and the voltage of the uncovered treatment group. However, the ion wind speed of the covered group was nearly zero, indicating that the petri dish cover could effectively block the ion wind. The microscopic morphology of naked oat seed coat before and after HVEF treatment is shown in Figure 8. The grid structure can be clearly observed in the control group, and the boundaries of these square network structures can be clearly seen. As shown in Figure 8b, after the 8 kV uncovered treatment, small cracks formed on the surface of the seed coat, and it was obvious that surface cracks  Figure 7 shows the ion wind speed treated by HVEF under different voltages. It can be seen from the figure that there is a linear relationship between the ion wind speed and the voltage of the uncovered treatment group. However, the ion wind speed of the covered group was nearly zero, indicating that the petri dish cover could effectively block the ion wind. Fresh Weight (g)

Effect of HVEF on Naked Oat Seed Coat
Electric Voltage (kV) kV kV+covered Figure 6. Changes in fresh weight of naked oat seedlings after HVEF treatment. Figure 7 shows the ion wind speed treated by HVEF under different voltages. It can be seen from the figure that there is a linear relationship between the ion wind speed and the voltage of the uncovered treatment group. However, the ion wind speed of the covered group was nearly zero, indicating that the petri dish cover could effectively block the ion wind.  The microscopic morphology of naked oat seed coat before and after HVEF treatment is shown in Figure 8. The grid structure can be clearly observed in the control group, and the boundaries of these square network structures can be clearly seen. As shown in Figure 8b, after the 8 kV uncovered treatment, small cracks formed on the surface of the seed coat, and it was obvious that surface cracks The microscopic morphology of naked oat seed coat before and after HVEF treatment is shown in Figure 8. The grid structure can be clearly observed in the control group, and the boundaries of these square network structures can be clearly seen. As shown in Figure 8b, after the 8 kV uncovered treatment, small cracks formed on the surface of the seed coat, and it was obvious that surface cracks were more than those in Figure 8c after the covered treatment. It can be seen from Figure 8d,e that the boundary of the surface network structure after the 16 kV and 20 kV uncovered treatment becomes blurred and difficult to identify, and surface cracks become more obvious with the increase of voltage. It can be seen from Figure 8f that after the 20 kV covered treatment, the surface cracks of the seed coat were significantly reduced compared with the uncovered group.

Effect of HVEF on Naked Oat Seed Coat
Appl. Sci. 2019, 9, x FOR PEER REVIEW 8 of 14 were more than those in Figure 8c after the covered treatment. It can be seen from Figure 8d,e that the boundary of the surface network structure after the 16 kV and 20 kV uncovered treatment becomes blurred and difficult to identify, and surface cracks become more obvious with the increase of voltage. It can be seen from Figure 8f that after the 20 kV covered treatment, the surface cracks of the seed coat were significantly reduced compared with the uncovered group. The FTIR spectra of naked oat seed coat after HVEF treatment is shown in Figure 9a. After the treatment of HVEF, the absorption peak intensity was enhanced at 3281 cm −1 , 1646 cm −1 , 1542 cm −1 , 1412 cm −1 and 1035 cm −1 , regardless of whether or not the petri dish was covered, and the uncovered group was enhanced more than the covered group. For the wave number at 1709 cm −1 and 1243 cm −1 , the absorption peak intensity was weakened. After the uncovered treatment of 16 kV, the peak strength changed more significantly than that of the 16 kV + covered group, indicating that the cover could effectively reduce the surface etching of seeds. Particularly interesting was that, as shown in Figure 9b, except for the 8 kV covered group, the HVEF treatment group formed a new absorption peak near 1740 cm −1 , and the shape of the absorption peak changed near 1035 cm −1 . After the treatment of HVEF, some peaks of FTIR were strengthened and weakened by different degrees and formed new absorption peaks, indicating that the chemical etching of naked oat seed coat by HVEF changed the chemical structure of naked oat seed coat. The FTIR spectra of naked oat seed coat after HVEF treatment is shown in Figure 9a. After the treatment of HVEF, the absorption peak intensity was enhanced at 3281 cm −1 , 1646 cm −1 , 1542 cm −1 , 1412 cm −1 and 1035 cm −1 , regardless of whether or not the petri dish was covered, and the uncovered group was enhanced more than the covered group. For the wave number at 1709 cm −1 and 1243 cm −1 , the absorption peak intensity was weakened. After the uncovered treatment of 16 kV, the peak strength changed more significantly than that of the 16 kV + covered group, indicating that the cover could effectively reduce the surface etching of seeds. Particularly interesting was that, as shown in Figure 9b, except for the 8 kV covered group, the HVEF treatment group formed a new absorption peak near 1740 cm −1 , and the shape of the absorption peak changed near 1035 cm −1 . After the treatment of HVEF, some peaks of FTIR were strengthened and weakened by different degrees and formed new absorption peaks, indicating that the chemical etching of naked oat seed coat by HVEF changed the chemical structure of naked oat seed coat.

ROS Content Changes Before and After Treatment with HVEF
As shown in Figure 10, the ROS content after treatment on the third day after inoculation was lower than that of the control group, and the ROS content was slightly higher than that of the covered treatment group after uncovered treatment. On the seventh day after inoculation, the ROS content after treatment was lower than on the third day, the ROS content of the treatment group was Figure 9. Infrared spectra of naked oat seed coat after HVEF treatment: (a) Infrared spectra of naked oat seed coat before and after treatment with 16 kV HVEF; (b) Infrared spectra of naked oat seed coat before and after treatment with different voltages, wherein a, b, c, d, e, f, g, h, i, j and k represent CK, 4 kV, 4 kV + covered, 8 kV, 8 kV + covered, 12 kV, 12 kV + covered, 16 kV, 16 kV + covered, 20 kV, 20 kV + covered, respectively.

ROS Content Changes Before and After Treatment with HVEF
As shown in Figure 10, the ROS content after treatment on the third day after inoculation was lower than that of the control group, and the ROS content was slightly higher than that of the covered treatment group after uncovered treatment. On the seventh day after inoculation, the ROS content after treatment was lower than on the third day, the ROS content of the treatment group was significantly lower than that of the control group and the ROS content of the uncovered treatment group was slightly higher than that of the covered group.
Appl. Sci. 2019, 9, x FOR PEER REVIEW 10 of 14 significantly lower than that of the control group and the ROS content of the uncovered treatment group was slightly higher than that of the covered group.

Discussion
HVEF biotechnology is a new type of high-efficiency bio-mutation technology, and the biological effect of HVEF is produced by the synergistic combination of various factors [12]. According to the analysis of its physical properties, the biological effect of the HVEF is mainly formed by two factors: one is the action of the non-uniform electric field, and the other is the role of discharge plasma. In HVEF, with the increase of discharge voltage, discharge plasma is produced, accompanied by the dissociation, excitation and ionization of gas molecules. Gas molecules undergo complex physical and chemical reactions, resulting in a large number of reactive oxygen and nitrogen species (RONS). RONS are important signal molecules in life activities and can react with bioactive molecules to change their structure. In HVEF, reactive agents (RAs) consist of active material RONS and a nonuniform electric field, which are the main components of ionic wind. RAs can directly penetrate the treatment body and even produce secondary effects [22]. Wang et al. also observed that RAs chemically etched the surface of seeds by oxidizing the organic components on the seed coat [23]. In order to explore the respective roles and contributions of two factors in the HVEF, when treating naked oat seeds, one group was directly exposed to the HVEF, and the other group was covered with a petri dish cover to block the physical and chemical etching of seeds by ion wind.
The HVEF can change the chemical structure and surface microstructure of naked oat seed coat, whether they are covered or not. This indicates that both the non-uniform electric field and discharge plasma can affect the microstructure of seed coat. It can be seen from the scanning electron microscope (SEM) results that after HVEF treatment with different voltages, the surface of the seeds was etched to have different degrees of cracks, showing stronger hydrophilicity and being more conducive to effective absorption of water and nutrients [23]. According to Figure 7, it can be seen that the ion wind speed of the HVEF without a cover increases with the increase of voltage. According to the microscopic morphology of the seed surface in Figure 8, the HVEF treatment caused the cracking of the naked oat seed coat, and with the increase of the ion wind speed, the surface of the seed coat was strengthened and the water absorption rate of the seed increased. The change in the seed coat after treatment with HVEF is related to the etching action of ion wind [12], and the cover treatment can effectively reduce ion wind etching. When there is no cover, multi-factor synergy has a greater influence on the microstructure of the seed coat, indicating that the ion wind etch has a Figure 10. Reactive oxygen species (ROS) content changes of seedlings after HVEF treatment (Different letters indicate statistically significant differences between treatments (p < 0.05)).

Discussion
HVEF biotechnology is a new type of high-efficiency bio-mutation technology, and the biological effect of HVEF is produced by the synergistic combination of various factors [12]. According to the analysis of its physical properties, the biological effect of the HVEF is mainly formed by two factors: one is the action of the non-uniform electric field, and the other is the role of discharge plasma. In HVEF, with the increase of discharge voltage, discharge plasma is produced, accompanied by the dissociation, excitation and ionization of gas molecules. Gas molecules undergo complex physical and chemical reactions, resulting in a large number of reactive oxygen and nitrogen species (RONS). RONS are important signal molecules in life activities and can react with bioactive molecules to change their structure. In HVEF, reactive agents (RAs) consist of active material RONS and a non-uniform electric field, which are the main components of ionic wind. RAs can directly penetrate the treatment body and even produce secondary effects [22]. Wang et al. also observed that RAs chemically etched the surface of seeds by oxidizing the organic components on the seed coat [23]. In order to explore the respective roles and contributions of two factors in the HVEF, when treating naked oat seeds, one group was directly exposed to the HVEF, and the other group was covered with a petri dish cover to block the physical and chemical etching of seeds by ion wind.
The HVEF can change the chemical structure and surface microstructure of naked oat seed coat, whether they are covered or not. This indicates that both the non-uniform electric field and discharge plasma can affect the microstructure of seed coat. It can be seen from the scanning electron microscope (SEM) results that after HVEF treatment with different voltages, the surface of the seeds was etched to have different degrees of cracks, showing stronger hydrophilicity and being more conducive to effective absorption of water and nutrients [23]. According to Figure 7, it can be seen that the ion wind speed of the HVEF without a cover increases with the increase of voltage. According to the microscopic morphology of the seed surface in Figure 8, the HVEF treatment caused the cracking of the naked oat seed coat, and with the increase of the ion wind speed, the surface of the seed coat was strengthened and the water absorption rate of the seed increased. The change in the seed coat after treatment with HVEF is related to the etching action of ion wind [12], and the cover treatment can effectively reduce ion wind etching. When there is no cover, multi-factor synergy has a greater influence on the microstructure of the seed coat, indicating that the ion wind etch has a greater influence on the micro-morphology of the seed coat than the non-uniform electric field, but this effect is not converted into a macroscopic effect.
Previous FTIR studies show that the wave number at 3281 cm −1 was the stretching vibrations of O-H and N-H of polysaccharides, sugar alcohols, glycosides, amino acids and proteins; the wave number at 2923 cm −1 was the asymmetric stretching vibrations of the -CH 3 of lipids and proteins; the wave number at 2853 cm −1 was the symmetrical telescopic vibration of -CH 2 from membrane lipid; the wave number at 1709 cm −1 was the stretching vibrations of C=O, indicative of cutin and wax; the wave numbers at 1646 cm −1 and 1542 cm −1 were indicative of protein amide I band and II band, respectively, the amide I band was formed by the stretching vibration coupling of C=O and the C-N group, the amide II band was formed by the stretching vibration coupling of N-H and C-N groups; the wave number near 1412 cm −1 was the bending vibration of -CH 2 , mainly from proteins and nucleic acid; the wave number near 1243 cm −1 was the asymmetric stretching vibration of the phosphodiester group, which mainly from the phosphodiester skeleton vibration of nucleic acid and phospholipid in the biofilm; the wave number near 1035 cm −1 was the symmetrical telescopic vibration mainly from the C-O-C vibration of phospholipids and sugars in the biofilm [24,25].
The surface of naked oat seeds is hydrophobic, the main components of the seed coat surface are cellulose and wax. Cellulose is hydrophilic and insoluble in water, while wax is hydrophobic. As shown in Figures 3 and 5, a large number of untreated naked oat seeds float on the surface of the water. After treatment by electric field, the number of floating seeds was greatly reduced, the hydrophilicity of naked oat seeds was increased and the hydrophilicity of the covered group increased more obviously, indicating that the non-uniform electric field impacts the hydrophilic seeds more than the ion wind. As shown in Figure 9, the wave numbers at 3281 cm −1 , 1646 cm −1 , 1542 cm −1 , 1412 cm −1 , and 1035 cm −1 were enhanced, indicating that the content of hydrophilic substances such as polysaccharides, sugar alcohols, cellulose and hemicellulose increased, these substances are all hydrophilic, especially hemicellulose and can cause the cell wall to swell, impart fiber elasticity and thus improve hydrophilicity. After the treatment of HVEF, the wave number at 1709 cm −1 was weakened, which is similar to the results of Himmelsbach and Wang et al. [23,26], indicating that the wax and oil content decreased, that is, the content of hydrophobic substances decreased, the change of these absorption peaks result in changes in the hydrophilicity of naked oat seeds. The new absorption peak formed near 1740 cm −1 of hemicellulose [23], which is conducive to the improvement of seed water absorption. In the results of the water absorption measurement in Figure 2, only the water absorption rate of the 8 kV uncovered group decreased slightly compared with the control, while the absorption peak of this group at 1740 cm −1 was not obvious. The water absorption rate of the 8 kV occlusion group did not change significantly compared with the control, this group did not form an absorption peak at 1740 cm −1 , while the other treatment groups formed a new absorption peak at 1740 cm −1 . The water absorption rate increased by different degrees compared with the control group, so whether an absorption peak is formed at 1740 cm −1 is closely related to the hydrophilicity of the seed, and whether it can be used as a judgment mark for the water absorption rate and hydrophilicity of the naked oat seed needs further research. Moreover, after the treatment of HVEF, the peak value of the FTIR of the uncovered group was more severe than that of the covered group, indicating that the ion wind etches the seed coat more seriously when it is not covered. This verifies that the ion wind etching has a greater influence on the microstructure of the seed coat than the non-uniform electric field.
The seed coat state plays an important role in regulating seed germination and seedling vigor. Studies have shown that etching can improve the hydrophilicity and water permeability of the seed epidermis, promoting its absorption of water and transfer to the endosperm and embryo [23]. According to the results of Meng et al. [27], we found that the moderate destruction of the seed coat by electric field treatment is conducive to seed germination. As shown in Figures 5 and 6, the height and fresh weight of naked oat seedlings were significantly increased after the treatment of HVEF compared with the control group, which indicates that the HVEF treatment can promote the seedling height of the germinated seedlings regardless of whether or not the germination rate is inhibited. Cramariuc et al. [28] treated potato seeds with an HVEF and found that electric field treatment had a positive effect on potato seed growth and yield (especially seed yield). This may be because the appropriate intensity of electric field treatment increases the permeability of biofilm, enhances the enzyme activity and thus speeds up the growth of seeds and increases the fresh weight. Wang et al. showed that electric field treatment can improve enzyme activity, increase cell membrane permeability, accelerate new cell formation, promote root and bud differentiation and growth and improve seed vigor [29], thereby promoting seedling growth after electric field treatment.
Studies have shown that ROS plays an important role in cell proliferation, differentiation and apoptosis and has the function of signaling molecules. ROS is an important marker connecting physical and biological interpretation of the connection of the electromagnetic causal chain. After HVEF treatment, the ROS generated in the cell matrix enters the cell and interacts with the macromolecules in the cell, thus changing the metabolic activity and genetic characteristics of cells [12]. Numerous studies have shown that ROS is harmful to organisms at high concentrations, and at low concentrations, ROS can act as a second messenger to mediate multiple responses of plants to hormones or environmental stress [30,31]. It can be seen from Figure 10 that after treatment with HVEF, the ROS content of naked oat has been significantly reduced, which is consistent with the research results of Sheteiwy et al. [32]. ROS reduction can be used as seed response to physicochemical etching of HVEF.

Conclusions
HVEF treatment can increase the content of hydrophilic substances, cellulose degradation and decrease the content of hydrophobic substances such as wax in the seed coat, thus increase the hydrophilicity of the seed. HVEF treatment can form a new absorption peak at 1740 cm −1 , which is closely related to the hydrophilicity of the seed. Ion wind etching has a greater impact on the micro-morphology of the seed coat, but this effect is not converted into a macroscopic effect, being covered can effectively reduce the etching degree of discharge plasma on seeds, reduce the field intensity received by seeds and make the radiation field received by seeds more uniform. The non-uniform electric field has a greater impact on the hydrophilicity of the seed.
Author Contributions: All authors have made significant contributions to this research. W.X. and Z.S. performed the majority of the experiments and wrote the manuscript; W.X., Z.S., X.L., C.D., Z.C., and X.M. contributed to the analysis of the data; and Z.S. designed and supervised the study and checked the final manuscript.