Seismic Vulnerability Analysis of Structure Subjected to Uneven Foundation Settlement

: Uneven foundation settlement is one of the common engineering problems in a collapsible loess area. In order to study the inﬂuence of uneven foundation settlement on the seismic performance of a structure, the incremental dynamic analysis (IDA) method is used to analyze the seismic vulnerability of the steel structure frame. The di ﬀ erences in the seismic response of the structure in relation to uneven foundation settlement are analyzed. The inﬂuences of uneven foundation settlement quantities and various areas of uneven settlement on the seismic response of the structure are discussed. On this basis, the relationship between ground motion intensity and structural failure probability is studied, by changing the magnitude of seismic acceleration peaks. Compared with the unsettled structure, the internal force redistribution of the structure caused by uneven foundation settlement is one of the causes of earthquake damage for some components. The uneven foundation settlement located at the corner of the plane of the structure is likely to cause more serious earthquake damage to the structure. Uneven settlement will cause an increase in storey drift. With the increase in settlement, the seismic damage of the superstructure will be aggravated.


Introduction
When the construction of a tunnel results in local cavities and insufficient thickness around the tunnel lining, this causes uneven settlement of the adjacent surface buildings' foundations and possibly unrecoverable damage [1][2][3].
Regarding this problem, much research has been carried out. The estimation of maximum building settlement is developed by the Potts and Addenbrooke method [4], numerical simulation [5], and InSAR monitoring data [6,7]. However, the monitoring and prediction of settlement is important, but the impact of settlement on the engineering structure is more concerning [8][9][10]. Most of the research on structural deformation assessment is carried out on greenfield ground [11], but the evaluation results are conservative [12]. In order to more accurately evaluate the ground movements, the impacts of structural weight [13,14] and stiffness [15][16][17][18] need to be considered.
However, most of the existing research focuses on ground movements and monitoring methods, or on the effects of tunnel excavation on the deformation of the superstructure. It is still very rare to study the dynamic response of structures after uneven foundation settlement, especially the study of the seismic response of structures after uneven foundation settlement, which is not found in related literature.
Settlement is a deformation feature of a building. It is the result of the vertical deformation of the foundation and the interaction of the building. Settlement is mainly divided into two categories: uniform settlement and uneven settlement [19,20]. Uniform settlement usually occurs when the load on the building and the foundation soil are relatively uniform. Uniform settlement generally does not cause secondary stress on the building structure and does not damage the building components, but excessive settlement can also cause a series of problems in practice. Uneven settlement is a kind of foundation deformation that occurs easily, often jeopardizing the safety of the building structure. In order to study the influence of uneven settlement on the seismic response of the structure, this paper takes a steel frame structure with an uneven foundation settlement as the research object. Different settling areas and settlements are set in the model, and the incremental dynamic analysis (IDA) method is used to calculate the structural seismic response. The seismic vulnerability analysis and evaluation of the structure are carried out by determining the damage index and performance parameters of the structure.

Seismic Vulnerability Analysis Process
For the accurate estimation of the complete range of structural earthquake response, incremental dynamic analysis (IDA) [21] is used as one of the most powerful analysis methods available. Based on the non-linear dynamic time history analysis, IDA analyzes the seismic performance level of the structural system through a large number of seismic calculation results. The method can be widely used in the process of structural seismic performance evaluation and vulnerability analysis, while considering factors such as the different seismic requirements of structures and the uncertainties of various parameters. As a nonlinear analysis method, IDA analysis can reflect the changes in a structural system with the change in ground motion intensity.
Using this series of seismic actions of different intensities for the structure and time-history analysis, we can calculate the relationship between the seismic response parameters and the ground motion intensity under the action of single ground motion, namely the IDA curve. An IDA curve includes the entire process of structural failure: the initial elastic phase, the intermediate elastoplastic deformation phase, and the final phase up until the structural instability collapses, so the IDA curve can very comprehensively reflect the relationship between ground motion and the structural response of different strengths. The incremental dynamic analysis method has two characteristics: predicting the responses of the structure under the influence of ground motion and accurately reflecting the change process of the structure's strength, stiffness, and deformation under earthquake action. Therefore, as an effective way to simulate the seismic collapse performance of structures, incremental dynamic analysis methods have been widely used worldwide.
Before the IDA analysis, in order to ensure the accuracy of the subsequent analysis results, it is necessary to determine a reasonable and effective ground motion intensity measure (IM), which is used to reflect the scaling factor of the record, and a damage measure (DM), which is used to evaluate the output of the corresponding non-linear dynamic analysis.

Analysis Parameter Selection and Setting
A set of ground motion records is needed to perform IDA. For mid-rise buildings, 10 to 20 records are usually enough to provide sufficient accuracy in the estimation of seismic demands [21,22]. A set of 10 ground motion records belonging to a bin of relatively large magnitudes of 6.5-6.9 and moderate distances were selected from current Pacific Earthquake Engineering Research Center terminology, listed in Table 1. The peak ground acceleration (PGA) was used as the ground motion intensity parameter. The advantage of PGA is that the concept is clear, the calculation is simple, and the existing ground motion attenuation relationship can be used to determine the seismic hazard.
Three performance levels of structures were divided by FEMA356 [23]: immediate occupancy (IO), life safety (LS), and collapse prevention (CP), and these three performance levels were always used to reflect the deformation properties of the component [24]. The maximum interstorey drift ratio, defined as the ratio of the maximum interstorey drift to the interstorey height, is a good measure of the Appl. Sci. 2019, 9,3507 3 of 17 responses of a structure. Therefore, the corresponding maximum interstorey drift ratio limits were set for each performance level. Furthermore, the deformation criterion was used to select the quantitative index, and the interstorey drift ratio θ max was selected as the quantitative index in this paper. The seismic waves selected in the previous section were scaled according to their intensity indexes, and 200 ground motion samples were generated from 0 to 2.0 g in increments of 0.1 g. The models were calculated by non-linear dynamic analysis, using SAP2000 v20 [25], which is a well-known commercial software tool for the analysis and design of structural systems. Advanced analytical techniques allow for step-by-step large deformation analysis, material nonlinear analysis with fiber hinges, and progressive collapse analysis, and nonlinear analyses can be static and/or time history, with options for fast nonlinear analysis nonlinear time history dynamic analysis and direct integration. The IDA was carried out to obtain the maximum interstorey drift ratios of the structure under different ground motion strengths.

Model Design
The remainder of this paper is organized as follows. The steel frame structure model is established, with the problem of uneven settlement. Three different foundation settlement zones, Zone I, Zone II, and Zone III, are set in the structural plane, and different settlement quantities of 20 mm, 40 mm, 60 mm, 80 mm, and 100 mm are sequentially set for each area. Furthermore, the IDA method is used to analyze the seismic responses of structures under different earthquakes, and the seismic vulnerability and seismic performance of each structure are further studied, as shown in Figure 1. The steel frame height was 3.2 m and the total height was 16.0 m. The beam was made of Hshaped steel, the beam section was W12 × 30, and the column was made of box steel. The cross-section of the bottom column was box 250 mm × 10 mm, and the remaining section of the column was box 200 mm × 10 mm. For designing the structural members, steel material with fy = 240 MPa was used.  The steel frame height was 3.2 m and the total height was 16.0 m. The beam was made of H-shaped steel, the beam section was W12 × 30, and the column was made of box steel. The cross-section of the bottom column was box 250 mm × 10 mm, and the remaining section of the column was box 200 mm × 10 mm. For designing the structural members, steel material with f y = 240 MPa was used.

Structural Seismic Vulnerability Analysis
The maximum interstorey drift ratios of the structure can reflect the comprehensive effects of structural damage, local damage, and layer height, and are easier to obtain during the analysis. Therefore, the maximum interstorey drift ratios of structures have become the most commonly used damage index in structural performance analysis and vulnerability research. Through the model IDA analysis, the median IDA curves were extracted, and Figure 2 shows the 50% probabilities of different settlement zones. The steel frame height was 3.2 m and the total height was 16.0 m. The beam was made of Hshaped steel, the beam section was W12 × 30, and the column was made of box steel. The cross-section of the bottom column was box 250 mm × 10 mm, and the remaining section of the column was box 200 mm × 10 mm. For designing the structural members, steel material with fy = 240 MPa was used.

Structural Seismic Vulnerability Analysis
The maximum interstorey drift ratios of the structure can reflect the comprehensive effects of structural damage, local damage, and layer height, and are easier to obtain during the analysis. Therefore, the maximum interstorey drift ratios of structures have become the most commonly used damage index in structural performance analysis and vulnerability research. Through the model IDA analysis, the median IDA curves were extracted, and Figure 2 shows the 50% probabilities of different settlement zones.
In order to more clearly show the influence of the uneven settlement area on the maximum interstorey drift ratios of the structure, the median line of the maximum interstorey drift ratios corresponding to different uneven settlement areas under the same settlement quantity is plotted in Figure 2.  (e) 80 mm (f) 100 mm It can be seen from Figure 3 that with the gradual increase in the settlement quantity, the difference in the maximum interstorey drift ratios of the structure corresponding to the three uneven settlement areas became more and more obvious. Among them, Zone I was the most obvious. The main reason for this is that Zone I was located at the corner of the structural plane. There was a large difference in the four-sided constraint. After the foundation is unevenly settled, the frame column will be inclined toward the relatively weak side. In addition, compared to Zone II and Zone III, the number of horizontal members connected to Zone I was relatively small, and it was difficult for the In order to more clearly show the influence of the uneven settlement area on the maximum interstorey drift ratios of the structure, the median line of the maximum interstorey drift ratios Appl. Sci. 2019, 9, 3507 5 of 17 corresponding to different uneven settlement areas under the same settlement quantity is plotted in Figure 2.
It can be seen from Figure 3 that with the gradual increase in the settlement quantity, the difference in the maximum interstorey drift ratios of the structure corresponding to the three uneven settlement areas became more and more obvious. Among them, Zone I was the most obvious. The main reason for this is that Zone I was located at the corner of the structural plane. There was a large difference in the four-sided constraint. After the foundation is unevenly settled, the frame column will be inclined toward the relatively weak side. In addition, compared to Zone II and Zone III, the number of horizontal members connected to Zone I was relatively small, and it was difficult for the frame columns to be internally distributed by adjacent members, making the zone more susceptible to damage. Contrary to this, Zone III was close to the center of the structural plane, and the surrounding constraints were relatively large and balanced, and the frame column of the subsidence zone was less prone to a tendency to one side. At the same time, the components in the adjacent area could also have a relatively sufficient internal force redistribution to the frame column, so that the larger internal force could be better distributed. It can be seen from Figure 3 that with the gradual increase in the settlement quantity, the difference in the maximum interstorey drift ratios of the structure corresponding to the three uneven settlement areas became more and more obvious. Among them, Zone I was the most obvious. The main reason for this is that Zone I was located at the corner of the structural plane. There was a large difference in the four-sided constraint. After the foundation is unevenly settled, the frame column will be inclined toward the relatively weak side. In addition, compared to Zone II and Zone III, the number of horizontal members connected to Zone I was relatively small, and it was difficult for the frame columns to be internally distributed by adjacent members, making the zone more susceptible to damage. Contrary to this, Zone III was close to the center of the structural plane, and the surrounding constraints were relatively large and balanced, and the frame column of the subsidence zone was less prone to a tendency to one side. At the same time, the components in the adjacent area could also have a relatively sufficient internal force redistribution to the frame column, so that the

Probabilistic Seismic Demand Analysis of Structures
Nonlinear dynamic time history analysis for 3600 analysis models was carried out, and the maximum interstorey drift ratio data points of the structure with the peak acceleration were obtained as variables, as shown in Figures 3-5. Figures 3-5 correspond to Zone I, Zone II, and Zone III,

Probabilistic Seismic Demand Analysis of Structures
Nonlinear dynamic time history analysis for 3600 analysis models was carried out, and the maximum interstorey drift ratio data points of the structure with the peak acceleration were obtained as variables, as shown in Figures 3-5. Figures 3-5 correspond to Zone I, Zone II, and Zone III, respectively. Each point in the graph represents the nonlinear dynamic time-history analysis of the structure response, obtained by the excitation of a ground motion sample. The vertical data points of each column in the figure are the responses of the structure under the same PGA. The horizontal red lines represent the different performance level limits for different performance levels LS1, LS2, LS3, and LS4 from bottom to top, and the specific values correspond to the quantitative index limits of the structure, as shown in the Table 2. From the bottom to the top, the different performance level limits LS1, LS2, LS3, and LS4 in turn represent basic integrity, minor damage, medium damage, severe damage, and collapse. These horizontal red lines are the dividing lines for the different levels of damage of the structure.
Appl. Sci. 2019, 9, x FOR PEER REVIEW 7 of 18 earthquake, the plastic hinge will dissipate as part of the seismic energy. A considerable number of plastic hinges appeared in the horizontal members connected to the uneven settlement zone and dissipate seismic energy during the earthquake, thereby mitigating the seismic response of the frame columns. Perhaps this is why the maximum interstorey drift ratios in some cases were higher for Zone I at 0 mm than in other cases.

Collapse Probability Analysis
The vulnerability curve of the structure indicates the probability that the structural demand exceeds a specific failure state under the action of different intensity earthquakes. Figures 6-8 are graphs showing the collapse probabilities of structures under earthquake action when different uneven settlement quantities occurred in Zone I, Zone II, and Zone III. It can be seen from the figures that as the earthquake intensity increased, the collapse probability of the structure increased significantly. However, in different uneven settlement areas, there was a certain difference in the collapse probability. When 100 mm of uneven settlement occurred, the peak acceleration of the 50% collapse probability of Zone I corresponded to 1.0 g, and Zone II and Zone III corresponded to 1.30 g and 1.33 g, respectively. This proves that when uneven settlement occurred in Zone I, the risk of structural collapse was higher. Of course, the earthquake collapse may be a partial collapse within a limited range in Zone I.  As can be seen from Figures 3-5, the seismic response of the frame structure corresponding to Zone I was generally larger than that of Zone II and Zone III. Moreover, even under the same intensity earthquake, as the settlement increased, more and more structural seismic responses reached greater performance level limits, which was particularly evident in Zone I.
Compared with the structure with no uneven foundation settlement, the uneven settlement made it easier for the structure to form a plastic hinge under the action of the earthquake. During an earthquake, the plastic hinge will dissipate as part of the seismic energy. A considerable number of plastic hinges appeared in the horizontal members connected to the uneven settlement zone and dissipate seismic energy during the earthquake, thereby mitigating the seismic response of the frame columns. Perhaps this is why the maximum interstorey drift ratios in some cases were higher for Zone I at 0 mm than in other cases.

Collapse Probability Analysis
The vulnerability curve of the structure indicates the probability that the structural demand exceeds a specific failure state under the action of different intensity earthquakes. Figures 6-8 are graphs showing the collapse probabilities of structures under earthquake action when different uneven settlement quantities occurred in Zone I, Zone II, and Zone III. It can be seen from the figures that as the earthquake intensity increased, the collapse probability of the structure increased significantly. However, in different uneven settlement areas, there was a certain difference in the collapse probability. When 100 mm of uneven settlement occurred, the peak acceleration of the 50% collapse probability of Zone I corresponded to 1.0 g, and Zone II and Zone III corresponded to 1.30 g and 1.33 g, respectively. This proves that when uneven settlement occurred in Zone I, the risk of structural collapse was higher. Of course, the earthquake collapse may be a partial collapse within a limited range in Zone I.        In Zone I, due to the different restraining action of the surrounding members on the corner column, it was easily inclined toward the side where the restraining action of lateral restraint was relatively weak when the foundation was unevenly settled. At the same time, the uneven settlement of the foundation and the seismic action caused the interstorey drift ratios to increase significantly, which led to damage of the corner column and its adjacent components. Although the direct damage caused in Zone I was localized, the possibility of progressive collapse of the entire structure cannot be ignored [26,27].
Compared with Zone I, when the structure had a 50% collapse probability under the same settlement conditions in Zone II and Zone III, the corresponding seismic acceleration peaks were larger. The reason for this is that Zone II and Zone III had more horizontal components connected to them, which had more load transfer paths and were also more constrained. Because the surrounding restraint was more uniform, the inclination of the column caused by uneven settlement in the uneven settlement area was relatively small. Therefore, the interstorey drift ratios of the columns in the area were mainly caused by earthquake action. This shows that the risk of collapse caused by the location of uneven settlement areas will be different, and the seismic damage of the components in the uneven settlement area can be effectively reduced by increasing the load transfer paths. In Zone I, due to the different restraining action of the surrounding members on the corner column, it was easily inclined toward the side where the restraining action of lateral restraint was relatively weak when the foundation was unevenly settled. At the same time, the uneven settlement of the foundation and the seismic action caused the interstorey drift ratios to increase significantly, which led to damage of the corner column and its adjacent components. Although the direct damage caused in Zone I was localized, the possibility of progressive collapse of the entire structure cannot be ignored [26,27].

Fragility Curves
Compared with Zone I, when the structure had a 50% collapse probability under the same settlement conditions in Zone II and Zone III, the corresponding seismic acceleration peaks were larger. The reason for this is that Zone II and Zone III had more horizontal components connected to them, which had more load transfer paths and were also more constrained. Because the surrounding restraint was more uniform, the inclination of the column caused by uneven settlement in the uneven settlement area was relatively small. Therefore, the interstorey drift ratios of the columns in the area were mainly caused by earthquake action. This shows that the risk of collapse caused by the location of uneven settlement areas will be different, and the seismic damage of the components in the uneven settlement area can be effectively reduced by increasing the load transfer paths. Figures 9-11 show the structural vulnerability curves. The abscissa indicates the magnitude of the ground motion, which is represented by PGA. The ordinate indicates the probability that the structural demand exceeds different performance levels under earthquake action. As can be seen from the figures, as the performance level progresses from the IO to the CP, the vulnerability curve gradually becomes gentler.

Fragility Curves
which led to damage of the corner column and its adjacent components. Although the direct damage caused in Zone I was localized, the possibility of progressive collapse of the entire structure cannot be ignored [26,27].
Compared with Zone I, when the structure had a 50% collapse probability under the same settlement conditions in Zone II and Zone III, the corresponding seismic acceleration peaks were larger. The reason for this is that Zone II and Zone III had more horizontal components connected to them, which had more load transfer paths and were also more constrained. Because the surrounding restraint was more uniform, the inclination of the column caused by uneven settlement in the uneven settlement area was relatively small. Therefore, the interstorey drift ratios of the columns in the area were mainly caused by earthquake action. This shows that the risk of collapse caused by the location of uneven settlement areas will be different, and the seismic damage of the components in the uneven settlement area can be effectively reduced by increasing the load transfer paths. Figures 9-11 show the structural vulnerability curves. The abscissa indicates the magnitude of the ground motion, which is represented by PGA. The ordinate indicates the probability that the structural demand exceeds different performance levels under earthquake action. As can be seen from the figures, as the performance level progresses from the IO to the CP, the vulnerability curve gradually becomes gentler.    The vulnerability curve of IO is the steepest, indicating that the probability of the structure surpassing the normal use performance level under earthquake action is large. As the structure progresses from IO to CP, the vulnerability curve of the structure gradually becomes flat, that is, the probability of transgression becomes smaller and smaller, which is in line with the structural design criteria. Under the same settlement condition, the vulnerability curve of each working condition in Zone I is steeper than that of Zone II and Zone III, indicating that the structural vulnerability had a higher probability of surpassing each state. In addition, in Zone I, the increase in uneven settlement had a more significant effect on the performance levels. It can be seen from Figure 9 that as the settlement increases the vulnerability curves become steeper, indicating that the increase in uneven settlement increases the risk of structural damage. For Zone II and Zone III, the effect of changes in settlement on the zones' performance levels was relatively small. The vulnerability curve of IO is the steepest, indicating that the probability of the structure surpassing the normal use performance level under earthquake action is large. As the structure progresses from IO to CP, the vulnerability curve of the structure gradually becomes flat, that is, the probability of transgression becomes smaller and smaller, which is in line with the structural design criteria. Under the same settlement condition, the vulnerability curve of each working condition in Zone I is steeper than that of Zone II and Zone III, indicating that the structural vulnerability had a higher probability of surpassing each state. In addition, in Zone I, the increase in uneven settlement had a more significant effect on the performance levels. It can be seen from Figure 9 that as the settlement increases the vulnerability curves become steeper, indicating that the increase in uneven settlement increases the risk of structural damage. For Zone II and Zone III, the effect of changes in settlement on the zones' performance levels was relatively small.

Analysis of Influencing Factors
In order to show the relationship between the uneven settlement, the seismic acceleration, and the displacement angle between the structural layers, a graph of the relationship between the three parameters was drawn. Due to limited space, the 10th ground motion record was taken as an example, as shown in Figure 12.
Appl. Sci. 2019, 9, x FOR PEER REVIEW 15 of 18 in the seismic acceleration peak. This phenomenon is particularly evident in the Zone II and Zone III uneven settlement areas. This shows that when the peak acceleration of the earthquake reached about 1.2 g, some components in the structure yielded, and the structural response caused by the earthquake reached a relatively stable state. The influence of uneven settlement on the structural response was most significant in Zone I. It can be seen that the interstorey drift ratios of the structure increased with the increase in uneven settlement under the same seismic acceleration. In Zone II and Zone III, even if the settlement quantity was greatly increased, the interstorey drift ratios of the structure did not show a corresponding large increase. Moreover, the larger the peak value of seismic acceleration, the smaller the influence of uneven settlement on the seismic response of the structure.

Conclusions
Through the above analysis, the following conclusions can be drawn: (1) Based on the seismic vulnerability curve of the structure, the damage probability of the structure under the given seismic action can be determined, which provides a basis for the damage assessment of earthquake disasters. According to the seismic vulnerability curve of such a structure in a region, the seismic vulnerability matrix of the regional system can be formed and used for earthquake prevention and disaster reduction planning in the region; (2) In addition to the seismic intensity, the uneven settlement area and the uneven settlement quantity will adversely affect the structural seismic response. As the uneven settlement increases, the structural seismic response will also increase. The uneven settlement area near the center of the structural plane has a relatively strong and balanced constraint on the surrounding area, and the seismic response of the structure is relatively small; (3) In this paper, only PGA was selected as a ground motion parameter to express the structural response and vulnerability curve. The acceleration response spectrum corresponding to the basic period of the structure could also be used as a ground motion parameter to study the vulnerability of the structure, so that the analysis results would be more universally applicable and the dispersion of the structural response data would be smaller; (4) For a building structure where the foundation uneven settlement areas are prone to occur, the foundation integrity should be enhanced, and a pile foundation form with a better anti-settling It can be seen from Figure 12 that no matter where the settlement zone is located in the structural plane, the ground motion intensity and the settlement quantity will affect the interstorey drift ratios. The interstorey drift ratios will increase with the increase of the acceleration peak. At the same time, the interstorey drift ratios will increase with the increase in settlement.
It can also be seen from Figure 12 that when the seismic acceleration peak is less than 1.2 g, the ground motion intensity has a significant influence on the interstorey drift ratios. When the seismic acceleration peak is greater than 1.2 g, the interstorey drift ratios no longer increase with the increase in the seismic acceleration peak. This phenomenon is particularly evident in the Zone II and Zone III uneven settlement areas. This shows that when the peak acceleration of the earthquake reached about 1.2 g, some components in the structure yielded, and the structural response caused by the earthquake reached a relatively stable state.
The influence of uneven settlement on the structural response was most significant in Zone I. It can be seen that the interstorey drift ratios of the structure increased with the increase in uneven settlement under the same seismic acceleration. In Zone II and Zone III, even if the settlement quantity was greatly increased, the interstorey drift ratios of the structure did not show a corresponding large increase. Moreover, the larger the peak value of seismic acceleration, the smaller the influence of uneven settlement on the seismic response of the structure.

Conclusions
Through the above analysis, the following conclusions can be drawn: (1) Based on the seismic vulnerability curve of the structure, the damage probability of the structure under the given seismic action can be determined, which provides a basis for the damage assessment of earthquake disasters. According to the seismic vulnerability curve of such a structure in a region, the seismic vulnerability matrix of the regional system can be formed and used for earthquake prevention and disaster reduction planning in the region; (2) In addition to the seismic intensity, the uneven settlement area and the uneven settlement quantity will adversely affect the structural seismic response. As the uneven settlement increases, the structural seismic response will also increase. The uneven settlement area near the center of the structural plane has a relatively strong and balanced constraint on the surrounding area, and the seismic response of the structure is relatively small; (3) In this paper, only PGA was selected as a ground motion parameter to express the structural response and vulnerability curve. The acceleration response spectrum corresponding to the basic period of the structure could also be used as a ground motion parameter to study the vulnerability of the structure, so that the analysis results would be more universally applicable and the dispersion of the structural response data would be smaller; (4) For a building structure where the foundation uneven settlement areas are prone to occur, the foundation integrity should be enhanced, and a pile foundation form with a better anti-settling effect should be adopted as much as possible to prevent the occurrence of uneven settlement. After uneven settlement occurs, it is necessary to strengthen the observation of deformations, especially for areas of uneven settlement near the outer side of the building plane.