Investigation of Physical Phenomena and Cutting Efﬁciency for Laser Cutting on Anode for Li-Ion Batteries

: Lithium-ion batteries have a higher energy density than other secondary batteries. Among the lithium-ion battery manufacturing process, electrode cutting is one of the most important processes since poor cut quality leads to performance degradation, separator protrusion, and local electric stress concentration. This may, eventually, lead to malfunction of lithium-ion batteries or explosion. The current mechanical cutting technology uses a contact process and this may lead to process instability. Furthermore, there are additional costs if the tools and cell design are changed. To solve these issues, laser cutting has been used. Conventional dependent parameters have limitations in investigating and explaining many physical phenomena during the laser cutting of electrodes. Therefore, this study proposes speciﬁc widths such as melting, top, and kerf width. Moreover, the relationship between laser parameters and multiphysical phenomena with the proposed widths are investigated. Five types of classiﬁcation with regard to physical phenomena are presented and explained with SEM images. Cutting efﬁciency is estimated with the proposed widths. The proposed speciﬁc cutting widths, ﬁve types of geometrical classiﬁcation, and cutting efﬁciency can be used as standardized parameters to evaluate the cutting quality.


Introduction
Lithium-ion batteries, which are secondary rechargeable batteries, have a higher energy density than other secondary batteries such as Ni-Cd batteries and Pd batteries if compared under the same conditions.Therefore, they can be used for energy storage devices, electronic devices, and electric vehicles, and demand for them has increased significantly [1].The lithium-ion manufacturing process can be categorized into two parts: (1) electrode coating and (2) cell assembly [2].During this manufacturing process, electrode cutting is one of the most important processes since poor cut quality leads to performance degradation.Moreover, defects such as burr and dross result in separator protrusion and local electric stress concentration.This may, eventually, lead to malfunction of lithium-ion batteries or explosion [3].Currently, die cutting or rotary knife cutting is used to cut electrodes.Since this process is a contact process, tools can be worn out and process instability can be observed with high possibility.Hence, this process instability has more chance to result in poor cut quality with defects such as burr and delamination.Furthermore, the lack of a standardized battery cell design leads to frequent changes in manufacturing specification, whenever the cell design is changed.Therefore, these frequent tool and design changes cause unexpected additional manufacturing cost.These disadvantages observed with current manufacturing methods can be improved by a laser cutting process due to its many advantages, such as being a noncontact process, with a high energy concentration, fast processing time, and higher flexibility for manufacturing design change.
Laser cutting has been applied with high popularity compared to other laser-aided manufacturing processes [4][5][6][7][8][9].Recently, laser cutting was applied to cut electrodes of lithium-ion batteries [10].The first laser technology using cost-efficient nanosecond laser cutting of electrodes was applied and successfully transferred to industry [10]. Lee et al. [2,[11][12][13][14][15][16][17][18][19][20] investigated physical phenomena during laser electrode cutting theoretically and experimentally with a continuous single-mode fiber laser.Lutely et al. [21,22] used a continuous(CW) and pulsed laser to cut lithium iron phosphate battery electrodes.They characterized the process efficiency and quality.They found that the cutting efficiency increases with shorter pulses, higher velocity, and shorter wavelength.Luetke et al. [23] investigated a comparative study on cutting electrodes for lithium-ion batteries with lasers.They compared a CW and pulsed laser to evaluate the cut quality by defining frazzling and clearance widths.They concluded that due to the high power range of the CW laser cutting system, it is advantageous in terms of cutting speed.In addition, the pulsed laser cutting system provides more opportunities for further improvements of the cutting quality.Demir et al. [24] compared the cut quality of laser cutting of lithium-ion electrodes with green (λ = 532 nm, τ = 1 ns) and infrared (λ = 1064 nm, τ = 250 ns) pulsed lasers.They found that the green laser provided a clearance width below 20 µm.In addition, the infrared laser met the high-productivity criterion with laser power of 54 W and a cutting speed of 30 m/min.While many physical phenomena occur during laser cutting, conventional parameters have been still used for the analysis of laser cutting, such as kerf width and penetration depth.Therefore, this study proposes specific parameters such as melting width, top width, and kerf width to analyze multiphysical phenomena more intuitively during the laser cutting of electrodes in addition to the conventional parameters.Moreover, the relationship between laser parameters and multiphysical phenomena with the proposed specific widths are investigated with cutting efficiency.This study is composed as follows.First, experimental setup and material used are explained.Second, the analysis of the cutting efficiency is explained.Third, the specific widths for the analysis of multiphysical phenomena are proposed.Further, the relationship between the laser parameters and the proposed specific parameters is discussed.Finally, the conclusions are presented.

Experimental Setup and Materials
The experimental setup can be found in Lee et al. [25].A single-mode Quasi-Continuous Ytterbium Fiber laser (IPG YLM-200/2000-QCW) was used in a continuous mode with a wavelength of 1070 nm.Its M 2 value was 1.05.The maximum average laser power was 250 W. The total thickness of the workpiece was 50 µm and an active electrode material was coated on a current collector with a thickness of 30 µm.The material of the active electrode was 90% graphite and 10% Polyvinylidene fluoride, which was used as a binder.The current collector material was a copper foil.The workpiece was placed on the flat plate and fixed at the end of the workpiece.The distance between the workpiece and the F-theta lens was 100 mm.The laser spot size was 23 µm.The laser parameters chosen were laser power and laser scanning speed since these play a major role during laser cutting.The laser power was varied from 50 W to 250 W with in steps of 50 W.The laser scanning speed was varied from 500 mm/s to 5000 mm/s in steps of 500 mm/s.The laser parameters used for the experiments are tabulated in Table 1 with a line energy.To observe the physical phenomena during laser cutting of the electrodes, Scanning Electron Microscopy (SEM) was used.The specific parameters for the analysis of physical phenomena are defined in Figure 1 for the anode.The top width (W top ) is defined by the width of the active electrode material removed by the laser, the melting width (W melt ) is defined by the width of the current collector with melting marks, and the kerf width (W ker f ) is defined as the fully removed width.

Analysis of Processing Efficiency
The heat transfer efficiency ( ℎ ) [26] is the efficiency of energy transmission from the source to the workpiece and defined as where   is power actually absorbed by the workpiece and   is total power available at the laser source.The processing efficiency (  ) is the thermal efficiency of energy conversion in the workpiece and defined as where   is the power required to melt, evaporate, and thus remove a given volume of material.From the measured widths and geometrical information, the power required to remove the material can be estimated.In addition, the total laser power available at the laser source is also estimated.Therefore, these efficiencies can be combined as Since there is no clear definition of this term, this term is named as the cutting efficiency (  ).Hence, first, the assumptions required to use the cutting efficiency need to be explained.Furthermore, the power required to melt, evaporate, and remove a given volume of material, as well as the total power available at the laser source, needs to be calculated.

Analysis of Processing Efficiency
The heat transfer efficiency (η th ) [26] is the efficiency of energy transmission from the source to the workpiece and defined as where P a is power actually absorbed by the workpiece and P i is total power available at the laser source.The processing efficiency (η p ) is the thermal efficiency of energy conversion in the workpiece and defined as where P p is the power required to melt, evaporate, and thus remove a given volume of material.From the measured widths and geometrical information, the power required to remove the material can be estimated.In addition, the total laser power available at the laser source is also estimated.Therefore, these efficiencies can be combined as Since there is no clear definition of this term, this term is named as the cutting efficiency (η c ).Hence, first, the assumptions required to use the cutting efficiency need to be explained.Furthermore, the power required to melt, evaporate, and remove a given volume of material, as well as the total power available at the laser source, needs to be calculated.

Assumptions
The geometrical assumption is shown in Figure 2.For simplicity, several rectangular parallelepipeds were assumed to express the material deformed by sublimation, melting, and evaporation.Since the cutting efficiency is estimated not during the laser cutting but after the laser cutting, no melting flow, boiling, or plasma formation was considered.A Gaussian laser beam distribution was assumed.The beam profile and radius do not change in the z-direction.

Assumptions
The geometrical assumption is shown in Figure .For simplicity, several rectangular parallelepipeds were assumed to express the material deformed by sublimation, melting, and evaporation.Since the cutting efficiency is estimated not during the laser cutting but after the laser cutting, no melting flow, boiling, or plasma formation was considered.A Gaussian laser beam distribution was assumed.The beam profile and radius do not change in the z-direction.

Laser Power Input (𝑷 𝒊𝒏 )
Laser intensity distribution can be expressed by a combination of a Gaussian beam profile and a Laguerre polynomial [15].This expression can be written as where  0 is the laser intensity,  = 2 2  2 is a parameter related to the laser beam radius () and distance () from the heat source, and  =  −1   is the angle between the reference direction on the chosen plane.The laser beam radius, which is one half of the beam diameter, was set to 11.5 μm in this study.The line from the origin,  (= √ 2 +  2 ), is the radial distance, and    is the associated Laguerre polynomial of order  and index .The Laguerre polynomial is expressed as From Equations ( 4) and ( 5), the laser power can be obtained and expressed as 2 0 0 ( , ) From Equation ( 4), when  = 0 and  = 0, the Gaussian distribution can be expressed as

Laser Power Input (P in )
Laser intensity distribution can be expressed by a combination of a Gaussian beam profile and a Laguerre polynomial [15].This expression can be written as where I 0 is the laser intensity, ρ = 2r 2 w 2 is a parameter related to the laser beam radius (w) and distance (r) from the heat source, and θ = tan −1 y  x is the angle between the reference direction on the chosen plane.The laser beam radius, which is one half of the beam diameter, was set to 11.5 µm in this study.
The line from the origin, r = x 2 + y 2 , is the radial distance, and L l p is the associated Laguerre polynomial of order p and index l.The Laguerre polynomial is expressed as From Equations ( 4) and ( 5), the laser power can be obtained and expressed as From Equation (4), when p = 0 and l = 0, the Gaussian distribution can be expressed as w 2 (7) where P 0 is a given laser power by a laser cutting system.Even though the laser power is given by the system, the real laser energy irradiated on the material surface could be different.Therefore, this study calculated a more precise laser power considering its approaching and leaving time.Laser power irradiation is shown in Figure 3. First, at the beginning of the laser cutting process, the laser is approaching the given area (2wl g ) and the laser power is increased to the certain laser power (P 0 ).After the laser is moving inside the given area with the given length (l g ), a constant laser power is maintained; then the laser power decreases as the laser is moving further away from the given area.
The given length (l g ) was set to 1 mm in this study.The length is cancelled out when calculating the efficiency.Based on this, the function of the laser power can be expressed as follows: where t a = 2w v is the approaching time, t l = l g v is the leaving time, and t f = is the final time.The detailed derivation is given in Appendix A. The total laser energy input irradiated in the given area can be calculated by integrating the graph shown in Figure 3 and its expression is shown as follows: where E in is the total laser energy, E a is the laser energy irradiated from the beginning to the approaching time, E c is the laser energy where the laser is fully irradiating the given area, and E l is the laser energy irradiated from the leaving time to the final time.Finally, the laser power input can be calculated by dividing the total laser energy by the working time.
Appl.Sci.2018, 8(2), 266 5 of 15 where   is a given laser power by a laser cutting system.Even though the laser power is given by the system, the real laser energy irradiated on the material surface could be different.Therefore, this study calculated a more precise laser power considering its approaching and leaving time.Laser power irradiation is shown in Figure .First, at the beginning of the laser cutting process, the laser is approaching the given area (  ) and the laser power is increased to the certain laser power (  ).
After the laser is moving inside the given area with the given length (  ), a constant laser power is maintained; then the laser power decreases as the laser is moving further away from the given area.
The given length (  ) was set to 1 mm in this study.The length is cancelled out when calculating the efficiency.Based on this, the function of the laser power can be expressed as follows:

Power Used for the Laser Cutting of Anode P p
Power used in cutting to sublimate, melt, and evaporate the anode can be derived from the geometrical volume removed and shown in Figure 2. The volume removed by sublimation is expressed by where d AE is the thickness of an active electrode material.The energy required to sublimate the given volume is expressed by where c AE is the specific heat of the active electrode material, m AE is the mass of the active electrode material, ρ AE is the density of the active electrode material, T sub is the sublimation temperature of the active electrode material, and T o is the ambient temperature.Volumes removed by melting and evaporation are, respectively, expressed by where d CC is the thickness of a current collector.In addition, the energy required to melt and evaporate, respectively, can be expressed by where c CC_s and c CC_l are the specific heat of the solid and liquid current collector, respectively; m CC_s and m CC_l are the mass of the solid and liquid current collector, respectively; T melt is the melting temperature of the current collector; T evap is the evaporation temperature of the current collector; L melt is the latent heat of fusion; and ρ CC_s and ρ CC_l are the density of the solid and liquid current collector, respectively.The total energy used to remove an anode is obtained as follows: Finally, the laser power used in the cutting of an anode can be calculated by dividing the total laser energy by the final time, or

Result and Discussion
Since various physical phenomena such as melting, molten pool formation, sublimation, evaporation, and re-solidification exist together, the above-mentioned widths were defined and used to explain the laser cutting process of electrodes for lithium-ion batteries.
The top width indicates that heat conduction and sublimation play a major role in removing the active electrode material or graphite due to sublimation.Hence, laser energy is absorbed on the top surface and transferred by conduction from the top surface to the body of graphite in the radial direction.When the body of the graphite reaches the sublimation temperature, the graphite is sublimated and the mass is removed.These heat transfer and material removal mechanisms are observable by investigating the top width.The physical phenomena such as melting, molten pool formation, and re-solidification are related to the melting width.From the kerf width, material removal caused by evaporation can be clearly observed.
Figure 4 shows the top width, melting width, and kerf width.From the figures, the x-axis is depicted with two variables-laser scanning speed (Left) and line energy (Right).The definition of line energy = P 0 πw 2 •v can be referred to [2,11].Figure 4a shows that increasing the scanning speed decreases the top width.With a laser power of 50 W, no top width is shown when the scanning speed is faster than 2000 mm/s.The top width is always observed when the laser power is greater than 50 W.In addition, increasing line energy increases top width.However, no active electrode material is removed when the line energy is less than 4.814 × 10 10 J/m 3 .Therefore, it is 4.814 × 10 10 J/m 3 that is the line energy required to remove an active electrode material.
Figure 4b shows the melting width.Increasing scanning speed decreases the melting width.No melting width is formed when the laser power is less than 150 W. When the scanning speed is faster than 2000 mm/s, the melting width is not formed with a laser power of 150 W. A melting width is always observable when the laser power is greater than 150 W. According to the line energy, a line energy greater than 0.963 × 10 10 J/m 3 is required to form the melting width.
The comparison of the kerf width is shown in Figure 4c.Increasing the scanning speed decreases the kerf width.No kerf width is observed when the laser power is less than 150 W. To fully penetrate the anode, a scanning speed less than 1500 mm/s is required with a laser power of 150 W. Furthermore, scanning speeds less than 2000 mm/s and 2500 mm/s are required to fully penetrate the anode with laser powers of 200 W and 250 W, respectively.Full penetration can be achieved when the line energy is greater than 3.009 × 10 10 J/m 3 .
Figures 4 and 5 show the variation of widths depending on laser power.SEM images are taken after the cutting is completed using the laser power of 250-50 W. Five types of classification with regard to physical phenomena are introduced and shown in Figure 6: (1) full penetration with wider top width of electrode; (2) partial penetration of current collector; (3) partial melting of current collector; (4) full ablation of active electrode material; and (5) partial ablation of active electrode material.It is interesting that full penetration with a narrower top width of the electrode is hardly observable.
Figure 7 shows SEM images with a laser power of 250 W and these show very significant changes in terms of physical phenomena from the full penetration to the partial penetration to the partial melting.With a laser scanning speed of 500 mm/s to 2000 mm/s, full penetration with a wider top width of the electrode is observed.The melting widths are clearly observed and these are relatively wide compared to the widths observed for cathode materials.Moreover, the difference between the top width and melting width is narrower than the difference between the melting width and kerf width.With a laser scanning speed of 2500 mm/s to 3500 mm/s, partial penetration of the current collector is observed.This may have occurred due to sporadic evaporation as illustrated in Figure 8.Thus, partial penetration occurs at the point where the evaporation occurs.On the other hand, more frequent evaporation occurrence may lead to full penetration.The physical mechanism of partial penetration was explained by Lee et al. [27].The forces caused by surface tension and recoil pressure are in a state of equilibrium and maintain a metastable state.When the force caused by surface tension increases, it leads to the formation of a connecting bridge as shown in Figure 8.On the other hand, increasing force caused by the recoil pressure results in full penetration.With a scanning speed of 4000 mm/s to 5000 mm/s, partial melting of the current collector is observed.The given laser parameters provide enough energy to remove the active electrode, but not enough energy to fully penetrate the current collector.Error!Reference source not found.shows SEM images with a laser power of 250 W and these show very significant changes in terms of physical phenomena from the full penetration to the partial penetration to the partial melting.With a laser scanning speed of 500 mm/s to 2000 mm/s, full   Error!Reference source not found.shows SEM images with a laser power of 250 W and these show very significant changes in terms of physical phenomena from the full penetration to the partial penetration to the partial melting.With a laser scanning speed of 500 mm/s to 2000 mm/s, full al.[27].The forces caused by surface tension and recoil pressure are in a state of equilibrium and maintain a metastable state.When the force caused by surface tension increases, it leads to the formation of a connecting bridge as shown in Error!Reference source not found.. On the other hand, increasing force caused by the recoil pressure results in full penetration.With a scanning speed of 4000 mm/s to 5000 mm/s, partial melting of the current collector is observed.The given laser parameters provide enough energy to remove the active electrode, but not enough energy to fully penetrate the current collector.partial penetration of the current collector is observed.This may have occurred due to sporadic evaporation as illustrated in Error!Reference source not found.. Thus, partial penetration occurs at the point where the evaporation occurs.On the other hand, more frequent evaporation occurrence may lead to full penetration.The physical mechanism of partial penetration was explained by Lee et al. [27].The forces caused by surface tension and recoil pressure are in a state of equilibrium and maintain a metastable state.When the force caused by surface tension increases, it leads to the formation of a connecting bridge as shown in Error!Reference source not found.. On the other hand, increasing force caused by the recoil pressure results in full penetration.With a scanning speed of 4000 mm/s to 5000 mm/s, partial melting of the current collector is observed.The given laser parameters provide enough energy to remove the active electrode, but not enough energy to fully penetrate the current collector.SEM images with a laser power of 200 W are shown in Figure 9.This also shows three types of physical phenomena such as full penetration of the electrode (laser scanning speed of 500 mm/s to 1500 mm/s), partial penetration of the current collector (laser scanning speed of 2000 mm/s to 2500 mm/s), and partial melting of the current collector (laser scanning speed of 3000 mm/s to 5000 mm/s).Under this laser power, a wider connecting bridge width is observed compared to the case of 250 W laser power.The full penetration and partial penetration of the current collector occur due to a combination of multiphysical phenomena such as heat conduction, heat convection, evaporation, melting, and re-solidification.On the contrary, the full and partial ablation of the active electrode material occurs with relatively simple physical phenomena such as heat conduction and the sublimation of graphite.mm/s), and partial melting of the current collector (laser scanning speed of 3000 mm/s to 5000 mm/s).Under this laser power, a wider connecting bridge width is observed compared to the case of 250 W laser power.The full penetration and partial penetration of the current collector occur due to a combination of multiphysical phenomena such as heat conduction, heat convection, evaporation, melting, and re-solidification.On the contrary, the full and partial ablation of the active electrode material occurs with relatively simple physical phenomena such as heat conduction and the sublimation of graphite.According to the analysis of the cutting efficiency discussed above, the cutting efficiency with appropriate material properties [15] for the case of full penetration is shown in Figure .The cutting efficiency varies from 14.6% to 37.7%.It is interesting that the cutting efficiency increases as the laser scanning speed increases.This is because losses due to thermal conduction make up a smaller portion of the absorbed energy [28].Therefore, a higher laser cutting speed providing full penetration leads to higher cutting efficiency and productivity.
SEM images with a laser power of 150 W are shown in  According to the analysis of the cutting efficiency discussed above, the cutting efficiency with appropriate material properties [15] for the case of full penetration is shown in Figure 10.The cutting efficiency varies from 14.6% to 37.7%.It is interesting that the cutting efficiency increases as the laser scanning speed increases.This is because losses due to thermal conduction make up a smaller portion of the absorbed energy [28].Therefore, a higher laser cutting speed providing full penetration leads to higher cutting efficiency and productivity.

Conclusions
To improve process stability and save additional cost, laser cutting was applied to cut electrodes for lithium-ion batteries.This study proposed specific widths such as melting width and top width for the analysis of laser cutting.The relationship between laser parameters, such as laser power, scanning speed, and line energy, and multiphysical phenomena with the proposed widths were investigated.Five types of geometrical classification with regard to physical phenomena were presented and explained with SEM images.Two or more types of physical phenomena were observed for each laser power level.Cutting efficiency was estimated with the proposed widths and its value varies from 14.6 to 37.7%.The cutting speed increases as the laser scanning speed increases.The specific cutting widths, five types of geometrical classification, and cutting efficiency proposed in this study will provide a standardized guideline for future research.SEM images with a laser power of 150 W are shown in Figure 11.In this figure, full penetration of the electrode and full ablation of the active electrode material are observed.Moreover, SEM images with a laser power of 100 W, as shown in Figure 12, show only one type of physical phenomenon-the full ablation of the active electrode material.With the given laser power, full ablation of the active electrode material is introduced between 1500 mm/s and 5000 mm/s.In addition, full ablation of the active electrode material is the only geometrical classification observable with the given laser power of 100 W. Contrary to the partial melting observed in Figure 9, no geometrical change is observed on a current collector with a laser power of 150 W or 100 W. The full ablation is the dominant physical phenomenon observed in Figures 11 and 12. Due to the wide processing window, these parameters causing the full ablation can be robustly used for the selective removal of the active electrode material with minimal damage to the current collector.Figure shows SEM images with a laser power of 50 W and two types of geometrical classification-the full and partial penetration of the active electrode material.With the given laser scanning speed of 500 mm/s and 2000 mm/s, full ablation of the active electrode material is seen.On the other hand, partial ablation of the active electrode material is observed when the laser scanning speed is between 2500 mm/s to 5000 mm/s.Under the given laser power, the top width is very similar to the laser spot size, or 23 μm, and the width of the partial ablation is less than the laser spot size.This can be possible since the Gaussian distribution of the laser beam is used.Figure shows SEM images with a laser power of 50 W and two types of geometrical classification-the full and partial penetration of the active electrode material.With the given laser scanning speed of 500 mm/s and 2000 mm/s, full ablation of the active electrode material is seen.On the other hand, partial ablation of the active electrode material is observed when the laser scanning speed is between 2500 mm/s to 5000 mm/s.Under the given laser power, the top width is very similar to the laser spot size, or 23 μm, and the width of the partial ablation is less than the laser spot size.This can be possible since the Gaussian distribution of the laser beam is used.Figure 13 shows SEM images with a laser power of 50 W and two types of geometrical classification-the full and partial penetration of the active electrode material.With the given laser scanning speed of 500 mm/s and 2000 mm/s, full ablation of the active electrode material is seen.On the other hand, partial ablation of the active electrode material is observed when the laser scanning speed is between 2500 mm/s to 5000 mm/s.Under the given laser power, the top width is very similar to the laser spot size, or 23 µm, and the width of the partial ablation is less than the laser spot size.This can be possible since the Gaussian distribution of the laser beam is used.
Figure shows SEM images with a laser power of 50 W and two types of geometrical classification-the full and partial penetration of the active electrode material.With the given laser scanning speed of 500 mm/s and 2000 mm/s, full ablation of the active electrode material is seen.On the other hand, partial ablation of the active electrode material is observed when the laser scanning speed is between 2500 mm/s to 5000 mm/s.Under the given laser power, the top width is very similar to the laser spot size, or 23 μm, and the width of the partial ablation is less than the laser spot size.This can be possible since the Gaussian distribution of the laser beam is used.

Conclusions
To improve process stability and save additional cost, laser cutting was applied to cut electrodes for lithium-ion batteries.This study proposed specific widths such as melting width and top width for the analysis of laser cutting.The relationship between laser parameters, such as laser power, scanning speed, and line energy, and multiphysical phenomena with the proposed widths were investigated.Five types of geometrical classification with regard to physical phenomena were presented and explained with SEM images.Two or more types of physical phenomena were observed for each laser power level.Cutting efficiency was estimated with the proposed widths and its value varies from 14.6 to 37.7%.The cutting speed increases as the laser scanning speed increases.The specific cutting widths, five types of geometrical classification, and cutting efficiency proposed in this study will provide a standardized guideline for future research.
Appl.Sci.2018, 8(2), 266 3 of 15 defined in Figure for the anode.The top width (  ) is defined by the width of the active electrode material removed by the laser, the melting width (  ) is defined by the width of the current collector with melting marks, and the kerf width (  ) is defined as the fully removed width.

Figure 2 .
Figure 2. Definition of areas for cutting efficiency.

Figure 2 .
Figure 2. Definition of areas for cutting efficiency.

Figure 3 .
Figure 3. Description of laser power irradiation with a laser power of 250 W, speed of 5000 mm/s, and distance of 100 μm.

Figure 3 .
Figure 3. Description of laser power irradiation with a laser power of 250 W, speed of 5000 mm/s, and distance of 100 µm.

Figure
Figure shows the variation of widths depending on laser power.Figure 7, figures 9-12 show SEM images after the cutting is completed using the laser power of 250-50 W, respectively.Five types of classification with regard to physical phenomena are introduced and shown in Figure : (1) full penetration with wider top width of electrode; (2) partial penetration of current collector; (3) partial melting of current collector; (4) full ablation of active electrode material; and (5) partial ablation of active electrode material.It is interesting that full penetration with a narrower top width of the electrode is hardly observable.

Figure 7 ,
Figure shows the variation of widths depending on laser power.Figure 7, figures 9-12 show SEM images after the cutting is completed using the laser power of 250-50 W, respectively.Five types of classification with regard to physical phenomena are introduced and shown in Figure : (1) full penetration with wider top width of electrode; (2) partial penetration of current collector; (3) partial melting of current collector; (4) full ablation of active electrode material; and (5) partial ablation of active electrode material.It is interesting that full penetration with a narrower top width of the electrode is hardly observable.

Figure 6 .
Figure 6.Category of five physical phenomena: (a) full penetration with a wider top width of the electrode; (b) the partial penetration of current collector; (c) the partial melting of the current collector; (d) full ablation of active electrode material; (e) partial ablation of active electrode material.

Figure 6 .
Figure 6.Category of five physical phenomena: (a) full penetration with a wider top width of the electrode; (b) the partial penetration of current collector; (c) the partial melting of the current collector; (d) full ablation of active electrode material; (e) partial ablation of active electrode material.

Figure 6 .
Figure 6.Category of five physical phenomena: (a) full penetration with a wider top width of the electrode; (b) the partial penetration of current collector; (c) the partial melting of the current collector; (d) full ablation of active electrode material; (e) partial ablation of active electrode material.

Figure 7 .
Figure 7. SEM images with a laser power of 250 W.

Figure 8 .
Figure 8. Evaporation points for (a) partial penetration and (b) full penetration.

Figure 7 .
Figure 7. SEM images with a laser power of 250 W.

Figure 7 .
Figure 7. SEM images with a laser power of 250 W.

Figure 8 .
Figure 8. Evaporation points for (a) partial penetration and (b) full penetration.

Figure 8 .
Figure 8. Evaporation points for (a) partial penetration and (b) full penetration.

Figure 9 .
Figure 9. SEM images with a laser power of 200 W.
Figure .In this figure, full penetration of the electrode and full ablation of the active electrode material are observed.Moreover, SEM images with a laser power of 100 W, as shown in Figure , show only one type of physical phenomenon-the full ablation of the active electrode material.With the given laser power, full ablation of the active electrode material is introduced between 1500 mm/s and 5000 mm/s.In addition, full ablation of the active electrode material is the only geometrical classification observable with the given laser power of 100 W. Contrary to the partial melting observed in Figure , no geometrical change is observed on a current collector with a laser power of 150 W or 100 W. The full ablation is the dominant physical phenomenon observed in Figure and 11.Due to the wide processing window, these parameters causing the full ablation can be robustly used for the selective removal of the active electrode material with minimal damage to the current collector.

Figure 9 .
Figure 9. SEM images with a laser power of 200 W.

Figure 13 .
Figure 13.Cutting efficiency for full penetration.

Figure 10 .
Figure 10.Cutting efficiency for full penetration.

15 Figure 10 .
Figure 10.SEM images with a laser power of 150 W.

Figure 11 .
Figure 11.SEM images with a laser power of 100 W.

Figure 12 .
Figure12.SEM images with a laser power of 50 W.

Figure 11 .
Figure 11.SEM images with a laser power of 150 W.

15 Figure 10 .
Figure 10.SEM images with a laser power of 150 W.

Figure 11 .
Figure 11.SEM images with a laser power of 100 W.

Figure 12 .
Figure12.SEM images with a laser power of 50 W.

Figure 12 .
Figure 12.SEM images with a laser power of 100 W.

Figure 12 .
Figure 12.SEM images with a laser power of 50 W.Figure 13.SEM images with a laser power of 50 W.

Figure 13 .
Figure 12.SEM images with a laser power of 50 W.Figure 13.SEM images with a laser power of 50 W.