Fabrication Process and Performance Analysis of CSP LED Filaments with a Stacked Package Design

This article presents a chip-scale package (CSP) based filament light-emitting diodes (LEDs) with a stacked-type structure and a segmented-type luminescence design for higher luminous efficiency and better electrical stability. The innovation strategy improves the luminous efficiency by 7.69% and 18.97% than the traditional dispensing packaged LED filament when the current is at 30 mA and 210 mA, respectively, and reduces the use of red phosphors and green phosphors by 66.7% and 26.2%, respectively. With the increase of the current, the luminous efficiency variations of the stacked-packaged filament are lower than that of the traditional dispensing packaged filament. Moreover, the color temperature of the filament is no longer determined by the calculation of the ratio of various phosphors. The stacked structure and the segmented design can help us to adjust the specified color temperature quickly by changing the proportion and position of the blue chips and the red CSP LEDs.

Attributed to their high efficiency, long life, low power consumption, environmental friendliness, tiny size, and directionality, the recently-developed phosphor-converted white light-emitting diode (WLED) have become the most promising substitute to conventional light sources [1][2][3][4].However, there are still many problems, including the improvement of phosphor conversion and luminous efficiency [5], and improvements in color purity for their substitution of cheaper incandescent and fluorescent lamps that currently occupy the global lighting market [6].
Presently, light-emitting diode (LED) filaments are a fervent LED product.They have three-dimensional luminescence and high plasticity, and can control light distribution according to the application environment.In contrast, the shortcomings are also very prominent, such as low color purity, low light efficiency, and low heat dissipation, so it is difficult to meet the standards of indoor lighting.The dispensing method of traditional LED filament packaging technology has a large variation in optical performance and the drift of color temperature under different currents [7,8].Color purity is the key to improving luminous efficiency and light output.The blue InGaN LED chip pumped by blue/green phosphor is a mature technology; however, these lack red components [9].Therefore, the mixing of a red phosphor viz.Sr 2 Si 5 N 8 : Eu 2+ and green/yellow phosphor, namely, yttrium aluminum garnet (YAG): Ce 3+ or SrSi 2 O 2 N 2 : Eu 2+ , is one method to overcome the problem of impure color.Nevertheless, low color purity can be caused by spectral overlapping, which happens when the partial reabsorption of emitted light by another phosphor, mixed with the design of the two phosphors, occurs.[10][11][12][13][14][15].To tackle this problem, stacked phosphor layers were developed by stacking green and red phosphor layers, which have been found to have higher efficiencies.This design showed that the reabsorption of green emissions by red components is reduced, when a red phosphor is used under the green phosphor layer [16].
However, thus far, most of the research on stacked package structures is focused on remote type packages, such as phosphor in glass (PiG), fluorescent film, and other forms [17,18].For example, Xiang et al. [19] found that screen-printing a red phosphor layer on LuAG:Ce 3+ PiG obtained a thermally-stable warm WLED. Lee et al. [20] designed a new phosphor design for reducing the spectral overlapping of PiGs, by cutting and reassembling commercial green Lu 3 Al 5 O 12 : Ce 3+ (LuAG:Ce 3+ ) and red CaAlSiN 3 : Eu 2+ (CASN:Eu + ) PiGs.Inspired by what has been explained above, our team planned to solve the performance problem of LED filaments by combining chip scale package (CSP) with a traditional dispensing method.In recent years, CSP has become a very popular research topic in the LED packaging field [21,22].The package size is only slightly larger than an LED chip, with an area ratio of 1.5:1 [23].CSP has the advantages of having a small package size and high assembly density [21].Thus, in this work, we report a new phosphor design for reducing the spectral overlapping of LED filaments by using a CSP layer and a layer of dispensing phosphor.

Experimental Section
The fluorescent film used for packaging is made by TECORE SYNCHEM, Inc., Tianjin, China, our partner company, using their self-developed preparing technology.A red-emitting phosphor CASN: Eu 2+ , with a wavelength of 618 nm, was used to make the fluorescent film with a mass fraction of 22.2 wt.%.The manufacturing process of CSP LEDs is shown in Figure 1.Firstly, under a certain pressure, rearranged chips were pressed into a softened film under vacuum conditions.Then, after being baked in an oven for three hours at a temperature of 300 • C, the pressed chips coated with film were cut into pieces, which we called CSP LEDs.After that, the red CSP LEDs were welded to a 135-mm long flexible substrate using a solid crystal machine.Each flexible filament substrate was welded with 51 CSP chips, which were connected in series.The uniform mixture of green-emitting phosphor LuAG:Ce 3+ and package resin was used as a second layer package for the CSP filament.Compared with the traditional dispensing packaging method, this packaging method is more complex but has a lower cost.overcome the problem of impure color.Nevertheless, low color purity can be caused by spectral overlapping, which happens when the partial reabsorption of emitted light by another phosphor, mixed with the design of the two phosphors, occurs.[10][11][12][13][14][15].To tackle this problem, stacked phosphor layers were developed by stacking green and red phosphor layers, which have been found to have higher efficiencies.This design showed that the reabsorption of green emissions by red components is reduced, when a red phosphor is used under the green phosphor layer [16].However, thus far, most of the research on stacked package structures is focused on remote type packages, such as phosphor in glass (PiG), fluorescent film, and other forms [17,18].For example, Xiang et al. [19] found that screen-printing a red phosphor layer on LuAG:Ce 3+ PiG obtained a thermally-stable warm WLED. Lee et al. [20] designed a new phosphor design for reducing the spectral overlapping of PiGs, by cutting and reassembling commercial green Lu3Al5O12: Ce 3+ (LuAG:Ce 3+ ) and red CaAlSiN3: Eu 2+ (CASN:Eu + ) PiGs.Inspired by what has been explained above, our team planned to solve the performance problem of LED filaments by combining chip scale package (CSP) with a traditional dispensing method.In recent years, CSP has become a very popular research topic in the LED packaging field [21,22].The package size is only slightly larger than an LED chip, with an area ratio of 1.5:1 [23].CSP has the advantages of having a small package size and high assembly density [21].Thus, in this work, we report a new phosphor design for reducing the spectral overlapping of LED filaments by using a CSP layer and a layer of dispensing phosphor.

Experimental Section
The fluorescent film used for packaging is made by TECORE SYNCHEM, Inc., Tianjin, China, our partner company, using their self-developed preparing technology.A red-emitting phosphor CASN: Eu 2+ , with a wavelength of 618 nm, was used to make the fluorescent film with a mass fraction of 22.2 wt.%.The manufacturing process of CSP LEDs is shown in Figure 1.Firstly, under a certain pressure, rearranged chips were pressed into a softened film under vacuum conditions.Then, after being baked in an oven for three hours at a temperature of 300 °C, the pressed chips coated with film were cut into pieces, which we called CSP LEDs.After that, the red CSP LEDs were welded to a 135-mm long flexible substrate using a solid crystal machine.Each flexible filament substrate was welded with 51 CSP chips, which were connected in series.The uniform mixture of green-emitting phosphor LuAG:Ce 3+ and package resin was used as a second layer package for the CSP filament.Compared with the traditional dispensing packaging method, this packaging method is more complex but has a lower cost.As mentioned above, stacked packaging structure can improve the optical efficiency of remote encapsulation of an LED.However, due to the air gap between the interfaces of the two packages, there are many optical phenomena, such as refraction, reflection and scattering at the interfaces [24].Therefore, LEDs with stacked packages will not reach the ideal light effect, and the light effect will even be reduced due to the excessive absorption and barrier of red phosphor to blue light when the red phosphor layer is under the green phosphor layer.Therefore, a dry-wet separation package method, on the basis of a stacked packaging structure, was adopted to eliminate the air gap by the wet layer wrapping the dry layer completely.
As we know, red-emitting phosphors CASN:Eu 2+ have strong absorption and blocking effects on blue emissions [25].The electro luminescence (EL) spectra obtained under the conditions of 30 mA and 140 V, and the corresponding Commission Internationale de L'Eclairage-1931 (CIE-1931) chromaticity coordinates tested by the Yuan Fang integral ball under a condition of 30 mA and 140 V, are shown in Figure 2a,b.The EL emission of the red CSP filament without the green package is composed of a blue emission at 450 nm, and a broad emission that occurs at wavelengths ranging from 550 to 700 nm; the former arises from the InGaN LED chip and the latter from the red CASN:Eu 2+ phosphors.However, the EL emission of the red CSP filament with a green package includes little blue emission at 450 nm, which means that the upper green phosphor almost completely absorbs the blue emissions emitted from the red CSP LEDs.With an increasing forward driving current, from 30 to 210 mA, the corresponding CIE-1931 chromaticity coordinates are presented in Figure 2b.A comparison of Commission Internationale de L'Eclairage (CIE) color coordination reveals that the emitting lights of these two samples are all in red.
As mentioned above, stacked packaging structure can improve the optical efficiency of remote encapsulation of an LED.However, due to the air gap between the interfaces of the two packages, there are many optical phenomena, such as refraction, reflection and scattering at the interfaces [24].Therefore, LEDs with stacked packages will not reach the ideal light effect, and the light effect will even be reduced due to the excessive absorption and barrier of red phosphor to blue light when the red phosphor layer is under the green phosphor layer.Therefore, a dry-wet separation package method, on the basis of a stacked packaging structure, was adopted to eliminate the air gap by the wet layer wrapping the dry layer completely.
As we know, red-emitting phosphors CASN:Eu 2+ have strong absorption and blocking effects on blue emissions [25].The electro luminescence (EL) spectra obtained under the conditions of 30 mA and 140 V, and the corresponding Commission Internationale de L'Eclairage-1931 (CIE-1931) chromaticity coordinates tested by the Yuan Fang integral ball under a condition of 30 mA and 140 V, are shown in Figure 2a,b.The EL emission of the red CSP filament without the green package is composed of a blue emission at 450 nm, and a broad emission that occurs at wavelengths ranging from 550 to 700 nm; the former arises from the InGaN LED chip and the latter from the red CASN:Eu2+ phosphors.However, the EL emission of the red CSP filament with a green package includes little blue emission at 450 nm, which means that the upper green phosphor almost completely absorbs the blue emissions emitted from the red CSP LEDs.With an increasing forward driving current, from 30 to 210 mA, the corresponding CIE-1931 chromaticity coordinates are presented in Figure 2b.A comparison of Commission Internationale de L'Eclairage (CIE) color coordination reveals that the emitting lights of these two samples are all in red.In order to fully stimulate the red-emitting phosphors and let parts of the blue light overflow stimulate the green emitting phosphors, a small improvement was applied to the filament structure.As shown in Figure 3, blue chips were arranged regularly between red CSP LEDs, and the proportions of red CSP and blue light chips were 2:1, 1:1, 1:2 and 1:3, respectively.This package can be seen as a combination of stacked-type and segmented-type packages.The mass fraction of red CASN:Eu 2+ in the film was determined, and the mass fraction of green LuAG:Ce 3+ and the proportion of CSP and blue chips is controllable.Thus, luminous performance can be designed by controlling these two parameters.In order to fully stimulate the red-emitting phosphors and let parts of the blue light overflow stimulate the green emitting phosphors, a small improvement was applied to the filament structure.As shown in Figure 3, blue chips were arranged regularly between red CSP LEDs, and the proportions of red CSP and blue light chips were 2:1, 1:1, 1:2 and 1:3, respectively.This package can be seen as a combination of stacked-type and segmented-type packages.The mass fraction of red CASN:Eu 2+ in the film was determined, and the mass fraction of green LuAG:Ce 3+ and the proportion of CSP and blue chips is controllable.Thus, luminous performance can be designed by controlling these two parameters.The four kinds of filaments mentioned above were dispensed with silicone resins in which the mass fractions of green LuAG:Ce 3+ phosphor were 14.3%, 20%, 29.4%.The CIE values obtained for the designed CSP LED filament samples, tested by the Yuan Fang integral ball under the conditions of 30 mA and 140 V, are shown in Figure 4, from which we can see that the CIE color coordination has a wide range of distribution, and the correlated color temperatures can be obtained from 2200 K to 4600 K.According to the requirements of indoor atmosphere lamps, samples with correlated color temperature (CCT) near 2500 K were used and compared with the traditional packaged LED filaments.The four kinds of filaments mentioned above were dispensed with silicone resins in which the mass fractions of green LuAG:Ce 3+ phosphor were 14.3%, 20%, 29.4%.The CIE values obtained for the designed CSP LED filament samples, tested by the Yuan Fang integral ball under the conditions of 30 mA and 140 V, are shown in Figure 4, from which we can see that the CIE color coordination has a wide range of distribution, and the correlated color temperatures can be obtained from 2200 K to 4600 K.According to the requirements of indoor atmosphere lamps, samples with correlated color temperature (CCT) near 2500 K were used and compared with the traditional packaged LED filaments.The four kinds of filaments mentioned above were dispensed with silicone resins in which the mass fractions of green LuAG:Ce 3+ phosphor were 14.3%, 20%, 29.4%.The CIE values obtained for the designed CSP LED filament samples, tested by the Yuan Fang integral ball under the conditions of 30 mA and 140 V, are shown in Figure 4, from which we can see that the CIE color coordination has a wide range of distribution, and the correlated color temperatures can be obtained from 2200 K to 4600 K.According to the requirements of indoor atmosphere lamps, samples with correlated color temperature (CCT) near 2500 K were used and compared with the traditional packaged LED filaments.

Results and Discussion
Figure 5 shows the practicality of two samples before and after the second-layer packaging.The first two samples were pure red CSP filaments, before and after the green LuAG:Ce 3+ packaging, respectively.The last sample was our designed filament, with a CCT of 2500 K, which emits the warm white light, and the upper one is the sample before the designed 2500 K filament packaging.It can be seen that the colors of each sample's emitting light were different.Although the last filament in Figure 5 is a segmented-type luminescence design, the luminescence appeared very homogeneous.This phenomenon was due to the second layer of green packaging providing ample space for light reflection, diffusion and deflection in the silicone matrix.The CSP filament of the laminated package is shown in Figure 6, and the dimensions of each part can be seen clearly.The thickness of the green packaging layer was nearly three times that of the red film thickness, which was a favorable space for photon multiple conversions, so the filament could give uniform illumination.

Results and Discussion
Figure 5 shows the practicality of two samples before and after the second-layer packaging.The first two samples were pure red CSP filaments, before and after the green LuAG:Ce 3+ packaging, respectively.The last sample was our designed filament, with a CCT of 2500 K, which emits the warm white light, and the upper one is the sample before the designed 2500 K filament packaging.It can be seen that the colors of each sample's emitting light were different.Although the last filament in Figure 5 is a segmented-type luminescence design, the luminescence appeared very homogeneous.This phenomenon was due to the second layer of green packaging providing ample space for light reflection, diffusion and deflection in the silicone matrix.The CSP filament of the laminated package is shown in Figure 6, and the dimensions of each part can be seen clearly.The thickness of the green packaging layer was nearly three times that of the red film thickness, which was a favorable space for photon multiple conversions, so the filament could give uniform illumination.The EL emission of the stacked package and traditional dispensing package filaments, shown in Figure 7, were composed of a blue emission at 450 nm, and a broad emission that occured at wavelengths ranging from 500 to 700 nm, the former from the InGaN LED chip and the latter from the green LuAG:Ce 3+ and red CASN:Eu 2+ phosphors.The green EL emission intensity of the stacked-type packaged filament was found to be higher than the traditional dispensing packaged filament.This may be ascribed to the decreased absorption of the LuAG:Ce 3+ 's green emission by the red-emitting CASN:Eu 2+ phosphor, thereby increasing green emission intensity.These phenomena clearly indicated that spectral overlapping was effectively reduced using a

Results and Discussion
Figure 5 shows the practicality of two samples before and after the second-layer packaging.The first two samples were pure red CSP filaments, before and after the green LuAG:Ce 3+ packaging, respectively.The last sample was our designed filament, with a CCT of 2500 K, which emits the warm white light, and the upper one is the sample before the designed 2500 K filament packaging.It can be seen that the colors of each sample's emitting light were different.Although the last filament in Figure 5 is a segmented-type luminescence design, the luminescence appeared very homogeneous.This phenomenon was due to the second layer of green packaging providing ample space for light reflection, diffusion and deflection in the silicone matrix.The CSP filament of the laminated package is shown in Figure 6, and the dimensions of each part can be seen clearly.The thickness of the green packaging layer was nearly three times that of the red film thickness, which was a favorable space for photon multiple conversions, so the filament could give uniform illumination.The EL emission of the stacked package and traditional dispensing package filaments, shown in Figure 7, were composed of a blue emission at 450 nm, and a broad emission that occured at wavelengths ranging from 500 to 700 nm, the former from the InGaN LED chip and the latter from the green LuAG:Ce 3+ and red CASN:Eu 2+ phosphors.The green EL emission intensity of the stacked-type packaged filament was found to be higher than the traditional dispensing packaged filament.This may be ascribed to the decreased absorption of the LuAG:Ce 3+ 's green emission by the red-emitting CASN:Eu 2+ phosphor, thereby increasing green emission intensity.These phenomena clearly indicated that spectral overlapping was effectively reduced using a The EL emission of the stacked package and traditional dispensing package filaments, shown in Figure 7, were composed of a blue emission at 450 nm, and a broad emission that occured at wavelengths ranging from 500 to 700 nm, the former from the InGaN LED chip and the latter from the green LuAG:Ce 3+ and red CASN:Eu 2+ phosphors.The green EL emission intensity of the stacked-type packaged filament was found to be higher than the traditional dispensing packaged filament.This may be ascribed to the decreased absorption of the LuAG:Ce 3+ 's green emission by the red-emitting CASN:Eu 2+ phosphor, thereby increasing green emission intensity.These phenomena clearly indicated that spectral overlapping was effectively reduced using a stacked-type package and segmented-type luminescence design.The decrease in spectral overlapping observed in the current design of the CSP filament can be attributed to the successful organization of the proximity of the luminescent elements in the assembled CSP filaments.The interaction of these optical centers at an optimum distance promotes the spatial delocalization of energy, minimizes energy transfer between the luminescent centers and thereby reduces the spectral overlapping.
stacked-type package and segmented-type luminescence design.The decrease in spectral overlapping observed in the current design of the CSP filament can be attributed to the successful organization of the proximity of the luminescent elements in the assembled CSP filaments.The interaction of these optical centers at an optimum distance promotes the spatial delocalization of energy, minimizes energy transfer between the luminescent centers and thereby reduces the spectral overlapping.With the same correlated color temperature of 2500 K, the CIE color coordinates of the aforementioned filaments are shown in Figure 8.The CIE color coordinates of both samples move to the left, but with two different trajectories, while the current increases from 30 to 210 mA.In the stacked-type filament, red fluorescent film can be considered to be in a state of excitation saturation; thus, with the increase in current, the emission of red light did not change obviously.Instead, the green phosphor stimulated more green light with an increasing intensity of blue light, so the color coordinates moved directly to the blue-green area.On the contrary, in the traditional dispensing package, phosphors were evenly dispersed in the silicone resins.As seen in Table 1, the luminous efficiency of the stacked-packaged filament was higher than that of the traditional dispensing packaged filament.With the increase in current, the luminous efficiency variations of the stacked-packaged filament were lower than that of the traditional dispensing packaged filament.This phenomenon can mainly be attributed to the reduction of photon reabsorption and the simplification of the photon transfer path.The general luminescence mechanism of Pc-White LEDs is the mixing of short wavelength light emitted by blue or UV LED chips and long-wavelength light emitted from phosphors pumped by the short wavelength light [26].It is considered a complicated energy-conversion and optical tracing process when the input light interacts with a phosphor.With the law of conservation of With the same correlated color temperature of 2500 K, the CIE color coordinates of the aforementioned filaments are shown in Figure 8.The CIE color coordinates of both samples move to the left, but with two different trajectories, while the current increases from 30 to 210 mA.In the stacked-type filament, red fluorescent film can be considered to be in a state of excitation saturation; thus, with the increase in current, the emission of red light did not change obviously.Instead, the green phosphor stimulated more green light with an increasing intensity of blue light, so the color coordinates moved directly to the blue-green area.On the contrary, in the traditional dispensing package, phosphors were evenly dispersed in the silicone resins.As seen in Table 1, the luminous efficiency of the stacked-packaged filament was higher than that of the traditional dispensing packaged filament.With the increase in current, the luminous efficiency variations of the stacked-packaged filament were lower than that of the traditional dispensing packaged filament.This phenomenon can mainly be attributed to the reduction of photon reabsorption and the simplification of the photon transfer path.The general luminescence mechanism of Pc-White LEDs is the mixing of short wavelength light emitted by blue or UV LED chips and long-wavelength light emitted from phosphors pumped by the short wavelength light [26].It is considered a complicated energy-conversion and optical tracing process when the input light interacts with a phosphor.With the law of conservation of energy, when a short wavelength light excites a phosphor, part of the energy is converted to long wavelength light and the other part is dissipated in the form of heat.As shown in Equation (F1), the input power from the blue LED chip (E input ) can be transferred to the blue photon energy that transmits out of silicone (E transmitted ), the absorbed energy by phosphors that is used for the light conversion (E converted ) and the heat generated from both Stokes shift (E ss ) and non-radiation (E nonRad ).
energy, when a short wavelength light excites a phosphor, part of the energy is converted to long wavelength light and the other part is dissipated in the form of heat.As shown in Equation (F1), the input power from the blue LED chip (Einput) can be transferred to the blue photon energy that transmits out of silicone (Etransmitted), the absorbed energy by phosphors that is used for the light conversion (Econverted) and the heat generated from both Stokes shift (Ess) and non-radiation (EnonRad).Within the optical tracing process, the light scattering, absorption and conversion are normally considered as dominant effects in most YAG based yellow phosphor models [27].As shown in Figure 9, light 1 is the blue light emitted by the chip, which is directly emitted through the package.When the blue light emitted by the chip propagates to the green phosphor, it is absorbed and transformed into green light like light 3, and the propagation direction is isotropic.Light 3 shows that the green light is not absorbed, but directly scattered through the green phosphor when the light fired by one green powder again propagates to another green phosphor.There are very few blue lights absorbed by the green phosphor that can propagate to the red phosphor, as light 4, that can then reabsorb the photon and turn into red light.The transmission direction of the emitting light of the red phosphor follows the same isotropy.When a blue light emitted by the chip reaches the red phosphor in the film, it is converted into red light like light 5, and then directly ejected.Some light, like light 6, does not reach any red phosphor and goes straight through the film.This kind of blue light is only absorbed by the green phosphor and emitted into green light.Light 7 indicates that the emitting light of the red phosphor will not be absorbed when the emitting light of the red phosphor is transmitted to the green phosphor, but instead the scattering phenomenon occurs.Light 8 indicates that blue light is absorbed by the red phosphor and no spectral transformation occurs.This is because the quantum efficiency of the red phosphor is much lower than that of the green phosphor, and the probability of non-radiative recombination is larger.Within the optical tracing process, the light scattering, absorption and conversion are normally considered as dominant effects in most YAG based yellow phosphor models [27].As shown in Figure 9, light 1 is the blue light emitted by the chip, which is directly emitted through the package.When the blue light emitted by the chip propagates to the green phosphor, it is absorbed and transformed into green light like light 3, and the propagation direction is isotropic.Light 3 shows that the green light is not absorbed, but directly scattered through the green phosphor when the light fired by one green powder again propagates to another green phosphor.There are very few blue lights absorbed by the green phosphor that can propagate to the red phosphor, as light 4, that can then reabsorb the photon and turn into red light.The transmission direction of the emitting light of the red phosphor follows the same isotropy.When a blue light emitted by the chip reaches the red phosphor in the film, it is converted into red light like light 5, and then directly ejected.Some light, like light 6, does not reach any red phosphor and goes straight through the film.This kind of blue light is only absorbed by the green phosphor and emitted into green light.Light 7 indicates that the emitting light of the red phosphor will not be absorbed when the emitting light of the red phosphor is transmitted to the green phosphor, but instead the scattering phenomenon occurs.Light 8 indicates that blue light is absorbed by the red phosphor and no spectral transformation occurs.This is because the quantum efficiency of the red phosphor is much lower than that of the green phosphor, and the probability of non-radiative recombination is larger.From the schematic diagram, Figure 9, we can clearly see that all light propagates in this special package structure.The excellent luminescence performance of the filament is mainly due to the absorption and transformation of some blue light directly by the green phosphor, which makes up for the defect that the red phosphor in the film blocks the light path, which leads to a reduction in luminous efficiency.
We also found that this special packaging structure can save a large amount of phosphor cost, using a simple calculation.The total mass of all packaging materials used for each traditional dispensing packaged filament was 0.278 g, and the mass fraction of red CASN:Eu 2+ phosphor and green LuAG:Ce 3+ phosphor were 3.0% and 20.89%, respectively.Thus, the masses of red phosphor and green phosphor in each filament were 0.00834 g and 0.05807 g, respectively.In comparison, in each stacked-type packaged filament, the total mass of the red CASN:Eu 2+ film was 0.0125 g, in which the mass fraction of red phosphor was 22.2%; meanwhile, the mass of the composition of the silicone matrix was 0.257 g, in which the mass fraction of green LuAG:Ce 3+ phosphor was 16.67%.As shown in Table 2, the mass of the red CASN:Eu 2+ phosphor and the green LuAG:Ce 3+ phosphor on each stacked filament was reduced by 66.7% and 26.2%, respectively, compared with the traditional packaged filament.

Conclusions
We have designed an innovative CSP filament with a stacked-type structure and a segmented-type luminescence design, opening a new area in luminous design and providing a better understanding of the tunability of optical properties.A faster and more accurate method to control the luminous parameters of filament has been developed.CCT, CRI and CIE can be set by arranging the proportion of red CSP LEDs and blue chips, or by changing the mass fraction of green phosphors.This fabrication also aimed to solve the spectral overlapping of green and red components for high power phosphor-based LED filaments.The proposed strategy improves luminous efficiency by 7.69% and 18.97%, more than the traditional dispensing packaged LED filament, when the current is at 30 mA and 210 mA, respectively, and this reduces the use of red phosphors and green phosphors by 66.7% and 26.2%, respectively.The protocol for the optical From the schematic diagram, Figure 9, we can clearly see that all light propagates in this special package structure.The excellent luminescence performance of the filament is mainly due to the absorption and transformation of some blue light directly by the green phosphor, which makes up for the defect that the red phosphor in the film blocks the light path, which leads to a reduction in luminous efficiency.
We also found that this special packaging structure can save a large amount of phosphor cost, using a simple calculation.The total mass of all packaging materials used for each traditional dispensing packaged filament was 0.278 g, and the mass fraction of red CASN:Eu 2+ phosphor and green LuAG:Ce 3+ phosphor were 3.0% and 20.89%, respectively.Thus, the masses of red phosphor and green phosphor in each filament were 0.00834 g and 0.05807 g, respectively.In comparison, in each stacked-type packaged filament, the total mass of the red CASN:Eu 2+ film was 0.0125 g, in which the mass fraction of red phosphor was 22.2%; meanwhile, the mass of the composition of the silicone matrix was 0.257 g, in which the mass fraction of green LuAG:Ce 3+ phosphor was 16.67%.As shown in Table 2, the mass of the red CASN:Eu 2+ phosphor and the green LuAG:Ce 3+ phosphor on each stacked filament was reduced by 66.7% and 26.2%, respectively, compared with the traditional packaged filament.

Conclusions
We have designed an innovative CSP filament with a stacked-type structure and a segmented-type luminescence design, opening a new area in luminous design and providing a better understanding of the tunability of optical properties.A faster and more accurate method to control the luminous parameters of filament has been developed.CCT, CRI and CIE can be set by arranging the proportion of red CSP LEDs and blue chips, or by changing the mass fraction of green phosphors.This fabrication also aimed to solve the spectral overlapping of green and red components for high power phosphor-based LED filaments.The proposed strategy improves luminous efficiency by 7.69% and 18.97%, more than the traditional dispensing packaged LED filament, when the current is at 30 mA and 210 mA, respectively, and this reduces the use of red phosphors and green phosphors by 66.7% and 26.2%, respectively.The protocol for the optical design of stacked-type structure filaments, possessing excellent tunability and high luminous efficiency, is an effort to make smarter high-powered LED filament devices.

Figure 2 .
Figure 2. (a) Electro luminescence (EL) spectra of pure red CSP filament before and after package; (b) the Commission Internationale de L'Eclairage (CIE)-1931 chromaticity coordinates of pure red CSP filament before and after package.

Figure 2 .
Figure 2. (a) Electro luminescence (EL) spectra of pure red CSP filament before and after package; (b) the Commission Internationale de L'Eclairage (CIE)-1931 chromaticity coordinates of pure red CSP filament before and after package.

Figure 4 .
Figure 4. CIE values obtained for designed CSP LED filament samples.

Figure 4 .
Figure 4. CIE values obtained for designed CSP LED filament samples.Figure 4. CIE values obtained for designed CSP LED filament samples.

Figure 4 .
Figure 4. CIE values obtained for designed CSP LED filament samples.Figure 4. CIE values obtained for designed CSP LED filament samples.

Figure 5 .
Figure 5.An actual image of the stacked type packaged filament.

Figure 6 .
Figure 6.A microscopic image of stacked type packaged filament.

Figure 5 .
Figure 5.An actual image of the stacked type packaged filament.

Figure 5 .
Figure 5.An actual image of the stacked type packaged filament.

Figure 6 .
Figure 6.A microscopic image of stacked type packaged filament.

Figure 6 .
Figure 6.A microscopic image of stacked type packaged filament.

Figure 7 .
Figure 7. EL spectra of traditional dispensing packaged filament and stacked-type packaged filament.

Figure 7 .
Figure 7. EL spectra of traditional dispensing packaged filament and stacked-type packaged filament.

Table 1 .
Electroluminescence data of traditional dispensing packaged filament and stacked-type packaged filament.

Table 1 .
Electroluminescence data of traditional dispensing packaged filament and stacked-type packaged filament.

Table 2 .
Mass of red CASN:Eu 2+ phosphors and green LuAG:Ce 3+ phosphors in each filament with different packaging methods.

Table 2 .
Mass of red CASN:Eu 2+ phosphors and green LuAG:Ce 3+ phosphors in each filament with different packaging methods.