Investigation on Eddy Current Sensor in Tension Measurement at a Resonant Frequency

: For resolving deﬁciencies of conventional tension measurement methods, this paper proposes a novel eddy current sensor with a single-coil structure based on the inverse magnetostrictive effect. An inductor–resistor–capacitor (LRC) model of eddy current sensor, which considers more parameters than the traditional inductor–resistor (LR) model, was established. The eddy current sensor was operated by a swept frequency signal that ranged from 0.1 MHz to 1.6 MHz, encompassing the sensor resonant frequency. At the resonant frequency, the data of impedance magnitude and phase were extracted and linear relations between the impedance parameters and the external tension were ascertained. The experimental results show that the resonant frequency and impedance magnitude of eddy current sensor will decrease linearly with the increase of the external tension, which is consistent with the theoretical model. In addition, to improve sensor performance, the sleeve structure was designed to reduce the loss of magnetic ﬁeld. Both ﬁnite element simulations and experimental results demonstrate that the sleeve structure provides a higher permeability path to the magnetic ﬁeld lines than the non-sleeve structure and effectively improves sensor sensitivity and correlation coefﬁcient.


Introduction
Steel cables are widely used in many civil engineering structures, such as long-span bridges, large gymnasiums, industrial factory buildings and rail stations. An increasing number of new large infrastructures are equipped with recently emerged structural health monitoring (SHM) systems to minimize unpredicted structural failure, which may cause economic and environmental damage as well as human casualties [1,2]. SHM is a fairly new concept to the field of civil engineering and SHM is intended to monitor structural behavior in real-time, evaluate structural performance under various loads and identify structural damage or deterioration [3]. Measuring cable tension in SHM is imperative during the service lives of steel structures. Damage in steel cables may induce collapse of whole bridges and result in the failure of entire infrastructures. The stress state of structures is used to determine when to replace them and how to prolong their useful lifetime or to retrofit them [4].
Traditional stress monitoring methods are the utilization of acceleration sensor, load cell and strain gauge. Based on the taut string theory, the vibration frequency measured by acceleration sensor is used to estimate cable tension [5]. However, due to the effects of sag and flexural rigidity of steel cables, the taut string theory will bring measurement inaccuracy. In addition, uncertainties of some parameters, such as mass, length and cross-sectional area, will produce significant errors in relation to turns are negligible. Thus, the sensor system can be modeled by the inductor-resistor (LR) circuit shown in Figure 2.
Appl. Sci. 2017, 7, 538 3 of 12 adjacent coil turns are negligible. Thus, the sensor system can be modeled by the inductor-resistor (LR) circuit shown in Figure 2.  According to Kirchhoff's Voltage Law, the equations can be expressed as follows: where 0 R and 0 L are the resistance and inductance of solenoid coil without the test specimen, 0 I and 1 I are the excitation current and induced eddy current, 1 R and 1 L are the resistance and inductance of induced eddy current, k is the coupling coefficient influenced by the skeleton thickness, ω is the angular frequency of alternating current excitation signal, and U is the voltage of excitation signal, respectively. The LR model can be remodeled as the equivalent model displayed in Figure 2b, which has a single-equivalent circuit as functions of 0 R , 0 L , 1 R and 1 L . The total impedance of the system is given by: where LR Z is the effective impedance, z R and z L are the equivalent resistance and inductance of solenoid coil, respectively.

LRC Model
The eddy current sensor is connected to the current source via a coaxial cable. For the case of high frequencies, the capacitances from the coaxial cable and adjacent coil turns need to be    According to Kirchhoff's Voltage Law, the equations can be expressed as follows: where 0 R and 0 L are the resistance and inductance of solenoid coil without the test specimen, 0 I and 1 I are the excitation current and induced eddy current, 1 R and 1 L are the resistance and inductance of induced eddy current, k is the coupling coefficient influenced by the skeleton thickness, ω is the angular frequency of alternating current excitation signal, and U is the voltage of excitation signal, respectively. The LR model can be remodeled as the equivalent model displayed in Figure 2b, which has a single-equivalent circuit as functions of 0 R , 0 L , 1 R and 1 L . The total impedance of the system is given by: where LR Z is the effective impedance, z R and z L are the equivalent resistance and inductance of solenoid coil, respectively.

LRC Model
The eddy current sensor is connected to the current source via a coaxial cable. For the case of high frequencies, the capacitances from the coaxial cable and adjacent coil turns need to be According to Kirchhoff's Voltage Law, the equations can be expressed as follows: where R 0 and L 0 are the resistance and inductance of solenoid coil without the test specimen, I 0 and I 1 are the excitation current and induced eddy current, R 1 and L 1 are the resistance and inductance of induced eddy current, k is the coupling coefficient influenced by the skeleton thickness, ω is the angular frequency of alternating current excitation signal, and U is the voltage of excitation signal, respectively. The LR model can be remodeled as the equivalent model displayed in Figure 2b, which has a single-equivalent circuit as functions of R 0 , L 0 , R 1 and L 1 . The total impedance of the system is given by: where Z LR is the effective impedance, R z and L z are the equivalent resistance and inductance of solenoid coil, respectively.

LRC Model
The eddy current sensor is connected to the current source via a coaxial cable. For the case of high frequencies, the capacitances from the coaxial cable and adjacent coil turns need to be considered. The considered. The eddy current sensor system can be approximately modeled as the combination of electronic components consisting of an inductor, a resistor and a parallel capacitor, known as an inductor-resistor-capacitor (LRC) circuit model. It is shown in Figure 3. The impedance of the coil in Figure 3 can be calculated as: When a swept frequency signal passes through the sensor coil, there occurs a frequency known as electrical resonance, at which the impedance magnitude becomes a maximum and impedance phase is zero. The general expression for the resonant frequency of LRC model can be given by: The impedance of coil is dependent on factors such as the gap between the sensor coil and the test specimen h , the resistivity of the test specimen ρ , the magnetic permeability of the test specimen μ and the frequency of the excitation signal f [23][24][25][26].
The tension in the test specimen changes the induced eddy current resulting in the measurable impedance variation in the sensor coil, which is acquired by an impedance analyzer.

Finite Element Analysis
A 2D axis-symmetric model of eddy current sensor was established using finite element analysis software ANSYS 15.0 (ANSYS, Pittsburgh, PA, America). The physical field was selected as the magnetic field under AC excitation and then solved using the harmonic solver [27]. The important parts were modeled with relatively fine mesh while the parts which do not need attention were modeled with relatively coarse mesh [28]. To investigate the influence of sleeve structure on the magnetic field strength distribution of the test specimen, two models with and without the sleeve structure were established. The simulation parameters were set as follows: the turns of coil were 204 and the diameter of enameled wire was 1 mm. The inner diameter and length of coil were 16 mm and 100 mm, respectively. The industrial pure iron DT4 was fabricated into the sleeve structure. The magnetic field lines and magnetic field strength distributions were acquired through the solution as shown in Figures 4 and 5, respectively. The impedance of the coil in Figure 3 can be calculated as: When a swept frequency signal passes through the sensor coil, there occurs a frequency known as electrical resonance, at which the impedance magnitude becomes a maximum and impedance phase is zero. The general expression for the resonant frequency of LRC model can be given by: The impedance of coil is dependent on factors such as the gap between the sensor coil and the test specimen h, the resistivity of the test specimen ρ, the magnetic permeability of the test specimen µ and the frequency of the excitation signal f [23][24][25][26].
The tension in the test specimen changes the induced eddy current resulting in the measurable impedance variation in the sensor coil, which is acquired by an impedance analyzer.

Finite Element Analysis
A 2D axis-symmetric model of eddy current sensor was established using finite element analysis software ANSYS 15.0 (ANSYS, Pittsburgh, PA, USA). The physical field was selected as the magnetic field under AC excitation and then solved using the harmonic solver [27]. The important parts were modeled with relatively fine mesh while the parts which do not need attention were modeled with relatively coarse mesh [28]. To investigate the influence of sleeve structure on the magnetic field strength distribution of the test specimen, two models with and without the sleeve structure were established. The simulation parameters were set as follows: the turns of coil were 204 and the diameter of enameled wire was 1 mm. The inner diameter and length of coil were 16 mm and 100 mm, respectively. The industrial pure iron DT4 was fabricated into the sleeve structure. The magnetic field lines and magnetic field strength distributions were acquired through the solution as shown in   It can be observed in Figure 4 that the utilization of a sleeve structure with the high permeability material concentrates the magnetic field and makes the magnetic field lines pass through the test specimen. In Figure 5, it is possible to observe that the magnetic field strength of the test specimen with the sleeve structure was higher than that without the sleeve structure. The simulation results demonstrate that the sleeve structure reduces reluctance in the magnetic circuit and provides a higher permeability path to magnetic field lines than the non-sleeve structure, thus reducing the loss of magnetic field.

Experimental Setup
The HP4294A precision impedance analyzer was used to produce a driving current of 20 mA and the sensor coil was operated through a swept frequency signal from 0.1 to 1.6 MHz. The absolute coil was constructed with 68 turns of a 1 mm diameter wire wound over three layers on the skeleton with a radius slightly larger than that of the test specimen. A digital phosphor oscilloscope with multiple channels was used to acquire signals across the sensor at a sampling frequency of   It can be observed in Figure 4 that the utilization of a sleeve structure with the high permeability material concentrates the magnetic field and makes the magnetic field lines pass through the test specimen. In Figure 5, it is possible to observe that the magnetic field strength of the test specimen with the sleeve structure was higher than that without the sleeve structure. The simulation results demonstrate that the sleeve structure reduces reluctance in the magnetic circuit and provides a higher permeability path to magnetic field lines than the non-sleeve structure, thus reducing the loss of magnetic field.

Experimental Setup
The HP4294A precision impedance analyzer was used to produce a driving current of 20 mA and the sensor coil was operated through a swept frequency signal from 0.1 to 1.6 MHz. The absolute coil was constructed with 68 turns of a 1 mm diameter wire wound over three layers on the skeleton with a radius slightly larger than that of the test specimen. A digital phosphor oscilloscope with multiple channels was used to acquire signals across the sensor at a sampling frequency of It can be observed in Figure 4 that the utilization of a sleeve structure with the high permeability material concentrates the magnetic field and makes the magnetic field lines pass through the test specimen. In Figure 5, it is possible to observe that the magnetic field strength of the test specimen with the sleeve structure was higher than that without the sleeve structure. The simulation results demonstrate that the sleeve structure reduces reluctance in the magnetic circuit and provides a higher permeability path to magnetic field lines than the non-sleeve structure, thus reducing the loss of magnetic field.

Experimental Setup
The HP4294A precision impedance analyzer was used to produce a driving current of 20 mA and the sensor coil was operated through a swept frequency signal from 0.1 to 1.6 MHz. The absolute coil was constructed with 68 turns of a 1 mm diameter wire wound over three layers on the skeleton with a radius slightly larger than that of the test specimen. A digital phosphor oscilloscope with multiple channels was used to acquire signals across the sensor at a sampling frequency of 1 GHz/s. The experimental system consisted of an eddy current sensor, a precision impedance analyzer (Dongguan Feiyu Electronics Co., Ltd., Dongguan, China), a digital phosphor oscilloscope (Tektronix, Beaverton, OR, USA), a digit multimeter (Shenzhen Wangbo Instrumentation Co., Ltd., Shenzhen, China), an acquisition circuit and a universal testing machine (Shanghai Xinrenda Instrumentation Co., Ltd., Shanghai, China) as shown in Figure 6.
Appl. Sci. 2017, 7, 538 6 of 12 1 GHz/s. The experimental system consisted of an eddy current sensor, a precision impedance analyzer (Dongguan Feiyu Electronics Co., Ltd., Dongguan, China), a digital phosphor oscilloscope (Tektronix, Beaverton, OR, USA), a digit multimeter (Shenzhen Wangbo Instrumentation Co., Ltd., Shenzhen, China), an acquisition circuit and a universal testing machine (Shanghai Xinrenda Instrumentation Co., Ltd., Shanghai, China) as shown in Figure 6. Equations (6)- (8) suggest that the impedance of the coil tends towards a maximum at the resonant frequency [29]. Thus the system can be separated into two regions where the inductive and capacitive components are dominant, respectively. The impedance phase will change at the resonant frequency from a positive to a negative regime. Before this frequency, the impedance of the coil is dominated by the inductive component. Thus, the system appears to be almost inductive. However, after this frequency the capacitive component in the system is dominantly contributing to the impedance of the coil and the sensor will cease to measure variation in the inductive component. Figure 7 shows the impedance magnitude and phase curves when the test specimen is under no external tension.  Equations (6)- (8) suggest that the impedance of the coil tends towards a maximum at the resonant frequency [29]. Thus the system can be separated into two regions where the inductive and capacitive components are dominant, respectively. The impedance phase will change at the resonant frequency from a positive to a negative regime. Before this frequency, the impedance of the coil is dominated by the inductive component. Thus, the system appears to be almost inductive. However, after this frequency the capacitive component in the system is dominantly contributing to the impedance of the coil and the sensor will cease to measure variation in the inductive component. Figure 7 shows the impedance magnitude and phase curves when the test specimen is under no external tension. 1 GHz/s. The experimental system consisted of an eddy current sensor, a precision impedance analyzer (Dongguan Feiyu Electronics Co., Ltd., Dongguan, China), a digital phosphor oscilloscope (Tektronix, Beaverton, OR, USA), a digit multimeter (Shenzhen Wangbo Instrumentation Co., Ltd., Shenzhen, China), an acquisition circuit and a universal testing machine (Shanghai Xinrenda Instrumentation Co., Ltd., Shanghai, China) as shown in Figure 6. Equations (6)- (8) suggest that the impedance of the coil tends towards a maximum at the resonant frequency [29]. Thus the system can be separated into two regions where the inductive and capacitive components are dominant, respectively. The impedance phase will change at the resonant frequency from a positive to a negative regime. Before this frequency, the impedance of the coil is dominated by the inductive component. Thus, the system appears to be almost inductive. However, after this frequency the capacitive component in the system is dominantly contributing to the impedance of the coil and the sensor will cease to measure variation in the inductive component. Figure 7 shows the impedance magnitude and phase curves when the test specimen is under no external tension.   According to the theoretical derivation, the resonant frequency can be influenced by the capacitance. The LRC parameters are listed in Table 1. When the external capacitance is 2.2 nF, 10 nF and 100 nF, the experimental results can be shown in Figure 8. According to the theoretical derivation, the resonant frequency can be influenced by the capacitance. The LRC parameters are listed in Table 1. When the external capacitance is 2.2 nF, 10 nF and 100 nF, the experimental results can be shown in Figure 8.  It is clear from Figure 8 that the resonant frequency declined with the increase of the external capacitance, which was consistent with the theoretical derivation. The sensor performance was carried out on a universal testing machine at room temperature. The experimental specimen was tested with the diameter of 12 mm and the length of 500 mm, the material of which was 45# carbon steel. During testing, the tension and displacement of the test specimen were recorded by an acquisition system, which was directly connected to the universal testing machine [30]. The loading tension was increased by increments of 3 kN up to 15 kN, which was in the elastic range of the test specimen.

Impedance Magnitude
As mentioned previously, the solenoid coil produces a circumferential current field into the test specimen, which creates an induced magnetic field that opposes the primary magnetic field. According to the variations of the impedance magnitude and phase, the eddy current sensor can detect the change of magnetic field caused by the external tension. Experimental analysis of the eddy current sensor was achieved by comparing the impedance magnitude signatures, as shown in Figure 9.  It is clear from Figure 8 that the resonant frequency declined with the increase of the external capacitance, which was consistent with the theoretical derivation. The sensor performance was carried out on a universal testing machine at room temperature. The experimental specimen was tested with the diameter of 12 mm and the length of 500 mm, the material of which was 45# carbon steel. During testing, the tension and displacement of the test specimen were recorded by an acquisition system, which was directly connected to the universal testing machine [30]. The loading tension was increased by increments of 3 kN up to 15 kN, which was in the elastic range of the test specimen.

Impedance Magnitude
As mentioned previously, the solenoid coil produces a circumferential current field into the test specimen, which creates an induced magnetic field that opposes the primary magnetic field. According to the variations of the impedance magnitude and phase, the eddy current sensor can detect the change of magnetic field caused by the external tension. Experimental analysis of the eddy current sensor was achieved by comparing the impedance magnitude signatures, as shown in Figure 9.
From Figure 9, it can be observed that the peak value of the impedance at the resonant frequency decreased with the increase of the external tension. Thus, the external tension of ferromagnetic materials specimen can be detected by measuring the peak value of sensor impedance. The experimental data were fitted and linear relationship between the peak value of impedance and the external tension was obtained. To reduce experimental error, the peak value of impedance was extracted in Figure 10 by averaging the six experimental results. The statistics of the repetitive experiments are listed in Table 2.
As mentioned previously, the solenoid coil produces a circumferential current field into the test specimen, which creates an induced magnetic field that opposes the primary magnetic field. According to the variations of the impedance magnitude and phase, the eddy current sensor can detect the change of magnetic field caused by the external tension. Experimental analysis of the eddy current sensor was achieved by comparing the impedance magnitude signatures, as shown in Figure 9.    Table 2 demonstrates that the coefficient of variation is around 0.14% in the loading and unloading processes, which means that the variation among the different repetitive experiments is small and sensor performance is repeatable. Hence, these variations among repetitive experiments will not affect the usability of such a system where the mean values are used to draw conclusions. As seen from Figure 10, the peak value of impedance varies with the increasing tension in a good linearity with the linear regression equation y = −2.771x + 1608.619 and a correlation coefficient of R 2 = 0.991 in Figure 9a, and the unloading process can be described with the linear regression equation y = −2.581x + 1604.857 and a correlation coefficient of R 2 = 0.986 in Figure 9b. Therefore, the results indicate the existence of a good linear relationship between the peak value of sensor impedance and the external tension.

Impedance Phase
The impedance phase results are shown in Figure 11. As can see from Figure 11, each point of the curve is the average of six repetitive experiments and contains two coordinates; one is the phase   Table 2 demonstrates that the coefficient of variation is around 0.14% in the loading and unloading processes, which means that the variation among the different repetitive experiments is small and sensor performance is repeatable. Hence, these variations among repetitive experiments will not affect the usability of such a system where the mean values are used to draw conclusions. As seen from Figure 10, the peak value of impedance varies with the increasing tension in a good linearity with the linear regression equation y = −2.771x + 1608.619 and a correlation coefficient of R 2 = 0.991 in Figure 9a, and the unloading process can be described with the linear regression equation y = −2.581x + 1604.857 and a correlation coefficient of R 2 = 0.986 in Figure 9b. Therefore, the results indicate the existence of a good linear relationship between the peak value of sensor impedance and the external tension.

Impedance Phase
The impedance phase results are shown in Figure 11. As can see from Figure 11, each point of the curve is the average of six repetitive experiments and contains two coordinates; one is the phase value and another is the frequency. As the external tension increased, the relative permeability of the test specimen changed and the sensor resonant frequency decreased.
Appl. Sci. 2017, 7, 538 9 of 12 value and another is the frequency. As the external tension increased, the relative permeability of the test specimen changed and the sensor resonant frequency decreased. Figure 11. Impedance phase analysis of eddy current sensor in the (a) loading and (b) unloading processes.
The resonant frequency at each tension is plotted and a good linear relationship is observed, as shown in Figure 12. The sensitivities are found to be around 0.468 kHz/kN in the loading process and 0.443 kHz/kN in the unloading process, which are slightly different due to the residual stress in the test specimen.

Correlation Coefficient
According to the repetitive experimental results, in order to obtain the relationship between the external tension and the impedance parameters, the data of impedance magnitude and phase at the resonant frequency were separately extracted and fitted into linear curves. To study the influence of sleeve structure on sensor performance, the correlation and relativity sensitivity coefficients of fitted curves with and without the sleeve structure were analyzed. Comparison results of correlation coefficient are shown in Table 3. Table 3. Comparison results of correlation coefficient.

Correlation Coefficient
Sleeve Structure Non-Sleeve Structure Figure 11. Impedance phase analysis of eddy current sensor in the (a) loading and (b) unloading processes.
The resonant frequency at each tension is plotted and a good linear relationship is observed, as shown in Figure 12. The sensitivities are found to be around 0.468 kHz/kN in the loading process and 0.443 kHz/kN in the unloading process, which are slightly different due to the residual stress in the test specimen.
Appl. Sci. 2017, 7, 538 9 of 12 value and another is the frequency. As the external tension increased, the relative permeability of the test specimen changed and the sensor resonant frequency decreased. The resonant frequency at each tension is plotted and a good linear relationship is observed, as shown in Figure 12. The sensitivities are found to be around 0.468 kHz/kN in the loading process and 0.443 kHz/kN in the unloading process, which are slightly different due to the residual stress in the test specimen.

Correlation Coefficient
According to the repetitive experimental results, in order to obtain the relationship between the external tension and the impedance parameters, the data of impedance magnitude and phase at the resonant frequency were separately extracted and fitted into linear curves. To study the influence of sleeve structure on sensor performance, the correlation and relativity sensitivity coefficients of fitted curves with and without the sleeve structure were analyzed. Comparison results of correlation coefficient are shown in Table 3. Table 3. Comparison results of correlation coefficient.

Correlation Coefficient
According to the repetitive experimental results, in order to obtain the relationship between the external tension and the impedance parameters, the data of impedance magnitude and phase at the resonant frequency were separately extracted and fitted into linear curves. To study the influence of sleeve structure on sensor performance, the correlation and relativity sensitivity coefficients of fitted curves with and without the sleeve structure were analyzed. Comparison results of correlation coefficient are shown in Table 3. It should be noted that all correlation coefficients exceed 0.974, indicating the existence of a linear relationship between the external tension and the impedance parameters of the sensor. Moreover, the sensor correlation coefficient with the sleeve structure was obviously larger than that with the non-sleeve structure. The reason for the larger coefficient is that the sleeve structure provides a higher permeability path to magnetic field lines than the non-sleeve structure, thus optimizing magnetic field distribution and improving sensor performances.

Relative Sensitivity Coefficient
The change in the impedance parameters of the sensor is proportional to the external tension and its normalized value can be calculated by: where S is the relative sensitivity, Z(T 0 ) and Z(T) are measured at 0 kN and at each 3 kN. Figure 13a,b shows the relative sensitivity change of the impedance magnitude and phase at the resonant frequency, respectively. It should be noted that all correlation coefficients exceed 0.974, indicating the existence of a linear relationship between the external tension and the impedance parameters of the sensor. Moreover, the sensor correlation coefficient with the sleeve structure was obviously larger than that with the non-sleeve structure. The reason for the larger coefficient is that the sleeve structure provides a higher permeability path to magnetic field lines than the non-sleeve structure, thus optimizing magnetic field distribution and improving sensor performances.

Relative Sensitivity Coefficient
The change in the impedance parameters of the sensor is proportional to the external tension and its normalized value can be calculated by: where S is the relative sensitivity, Z(T0) and Z(T) are measured at 0 kN and at each 3 kN. Figure 13a,b shows the relative sensitivity change of the impedance magnitude and phase at the resonant frequency, respectively.  Figure 13 illustrates that the sensor's relative sensitivity presents an increasing trend with the external tension changes from 0 kN to 15 kN with the loading step of 3 kN. Therefore, the data of impedance magnitude or impedance phase at the resonant frequency can be used to infer external tension. In addition, it is very clear that the presence of the sleeve structure improves the sensor's relative sensitivity. This improvement may be attributed to the fact that the sleeve structure allows more magnetic field lines to flow through the test specimen as a result of its higher permeability than the non-sleeve structure. This conclusion is supported by the finite element analysis in Section 3.

Conclusions and Future Work
In this paper, the LRC theoretical model of an eddy current sensor for tension measurement was presented based on the inverse magnetostrictive effect and impedance parameters approaching the resonant frequency were analyzed. The finite element model of the sensor was simulated and  Figure 13 illustrates that the sensor's relative sensitivity presents an increasing trend with the external tension changes from 0 kN to 15 kN with the loading step of 3 kN. Therefore, the data of impedance magnitude or impedance phase at the resonant frequency can be used to infer external tension. In addition, it is very clear that the presence of the sleeve structure improves the sensor's relative sensitivity. This improvement may be attributed to the fact that the sleeve structure allows more magnetic field lines to flow through the test specimen as a result of its higher permeability than the non-sleeve structure. This conclusion is supported by the finite element analysis in Section 3.

Conclusions and Future Work
In this paper, the LRC theoretical model of an eddy current sensor for tension measurement was presented based on the inverse magnetostrictive effect and impedance parameters approaching the resonant frequency were analyzed. The finite element model of the sensor was simulated and experimental tension measurement system was designed. The main conclusions from this work are as follows: (1) A novel sensor was designed, analyzed, and experimentally verified on 45# carbon steel with diameter of 12 mm. Compared with the traditional tension measurement methods, the eddy current sensor with a single-coil structure has the advantages of smaller size, lower cost, easier installation and less mutual interference. (2) This paper proposes a novel approach to tension measurement in ferromagnetic materials based on the impedance change of an eddy current sensor at the resonant frequency. In six repetitive experiments, the results show that the impedance parameters are efficient for estimating the tension. In all cases, the correlation coefficient reaches to 0.974 and the sensitivity coefficients are 2.581 ohms/kN in impedance magnitude analysis and 0.443 kHz/kN in impedance phase analysis, respectively. (3) In order to improve sensor performance, a sleeve structure was presented. Both finite element simulations and experimental results match well with the theoretical analysis, which indicates that the utilization of a sleeve structure remarkably improves sensor sensitivity and correlation coefficient.
In the next step, the flexible eddy current sensor will be further researched for repeatable use and easy installation and disassembly. In addition, due to the limitation of experimental conditions, the maximum loading tension is 15 kN, which is within 42% of the elastic tension. In the future, the measuring range of the sensor will be experimentally ascertained and the sensor performance will be studied over the elastic range of the test specimen. Furthermore, this paper is the preliminary study and has not considered the effects of temperature and sensor robustness. Hence, it is necessary to solve the problem of temperature compensation and improve sensor robustness in order to apply the sensor to practical applications, such as measuring tension in post-tensioning (PT) tendon, steel bar and steel cables.