Investigations on the Effects of Vortex-induced Vibration with Different Distributions of Lorentz Forces

The control of vortex-induced vibration (VIV) in shear flow with different distributions of Lorentz force is numerically investigated based on the stream function–vorticity equations in the exponential-polar coordinates exerted on moving cylinder for Re = 150. The cylinder motion equation coupled with the fluid, including the mathematical expressions of the lift force coefficient C l , is derived. The initial and boundary conditions as well as the hydrodynamic forces on the surface of cylinder are also formulated. The Lorentz force applied to suppress the VIV has no relationship with the flow field, and involves two categories, i.e., the field Lorentz force and the wall Lorentz force. With the application of symmetrical Lorentz forces, the symmetric field Lorentz force can amplify the drag, suppress the flow separation, decrease the lift fluctuation, and then suppress the VIV while the wall Lorentz force decreases the drag only. With the application of asymmetrical Lorentz forces, besides the above-mentioned effects, the field Lorentz force can increase additional lift induced by shear flow, whereas the wall Lorentz force can counteract the additional lift, which is dominated on the total effect.


Introduction
Bluff structures such as offshore spar, marine risers, overhead transmission lines and heat exchangers are subjected to vortex-induced vibration (VIV) when exposed to a flowing fluid, which contributes to the fatigue life reduction of structures and may produce structure damage under certain unfavorable conditions.The interactions between the shedding among various cylinders are much more complicated and they are also relevant to a number of problems.One of the problems where this is critical is concentrated solar power (CSP) collectors, where the shedding from one row affects the next one, leading to mechanical problems due to vibration and fatigue [1,2].The vibrations arise from the time-periodic fluid force associated with the time-periodic shedding vortex, and subsequently alter the flow field, which will change the flow-induced force in turn.Such fluid-structure interactions increase the complexity of the fluid mechanisms.
Extensive research on VIV has been conducted.The earliest studies have been the subject of interests with lock-in phenomenon of VIV (e.g., [3][4][5][6][7][8][9][10]).The time varying parameters such as cylinder response, flow force, vortex shedding and the influences of cylinder motion on the vortex structure are further studied [11][12][13][14], and the vortex-formation modes have been focused on later by [15][16][17][18], which paid attention to the interactions with multiple cylinders, and showed that the arrangement or gap had a significant effect on the VIV system responses.However, a large fluctuation of flow forces, and the increase of drag, acoustic noise and even structure damage are usually generated by the undesirable flow separations and vibrations of the body in the previous cases.Therefore, modern flow control approaches and technologies are considered to suppress the above phenomena.Flow control usually involves two broad categories.For one, called passive control, the flow is modified without external energy input as helical strakes [19], fin [20], rope and bump [21], thick fairings [22] (p.19377), splitter plates [23], guide foils [24] and so on.For the other, called active control, energy requires to be injected into the flow as momentum injections [25][26][27], moving-wall [28], synthetic jet actuators [29], suction and blowing [30][31][32][33][34] and so on.
The Lorentz force, one of the active approaches, has been subjected to various studies since the 1960s.In the recent years, the Lorentz force has attracted more attention due to its promising applications in engineering fields.Crawford and Karniadakis [35] has numerically investigated that the Lorentz force can eliminate the flow separation when the flow past a stationary cylinder, and the suppressing effect of the Lorentz force has been confirmed by Weier et al. [36] with both experiments and calculations.Later, in the cases of Kim and Lee [37] and Posdziech and Grundmann [38], it is found that both of the continuous and pulsed Lorentz forces can suppress the force fluctuation and stabilize the flow.Recently, optimal and closed-loop control have been developed by Zhang et al. [39][40][41] aiming to improve the control efficiency of the cylinder wake, and the VIV of the shear incoming flow was also investigated preliminarily [42].However, there has not been discussion in the literature on the control of VIV by Lorentz forces in shear flow.
In this paper, control of VIV with Lorentz forces for the shear flow has been numerically investigated.The stream function-vorticity equations, the initial and boundary conditions, distribution of hydrodynamic force and the cylinder motion equation are deduced in the exponential-polar coordinate with the coordinate at the moving cylinder.The Lorentz force can be classified into the field Lorentz force and the wall Lorentz force.On the other hand, the evolution of VIV starting from rest to vibration, and suppression are all presented.The mechanism of fluid-cylinder interactions in the shear flow with different distributions of Lorentz forces is discussed in detail.

Governing Equations
A circular cylinder experiences time varying lift and drag, which are related to the vortex shedding, when placed in a flowing fluid.Thus, time varying vibration will occur when the cylinder is constrained to move on flexible supports, which is known as vortex-induced vibration (VIV).Moreover, the fluid around the cylinder is altered by this vibration, which affects the induced hydrodynamic forces in turn and the structure response is then changed.Therefore, this problem is associated with fully coupled fluid-structure interactions.
For control of VIV in an electrically low-conducting fluid, the actuators on the cylinder surface consists of two half cylinders mounted with alternating electrodes and magnets as shown in Figure 1.The momentum of the fluid round the cylinder surface is increased with the application of Lorentz force, which is directed parallel to the cylinder surface.
However, a large fluctuation of flow forces, and the increase of drag, acoustic noise and even structure damage are usually generated by the undesirable flow separations and vibrations of the body in the previous cases.Therefore, modern flow control approaches and technologies are considered to suppress the above phenomena.Flow control usually involves two broad categories.For one, called passive control, the flow is modified without external energy input as helical strakes [19], fin [20], rope and bump [21], thick fairings [22] (p.19377), splitter plates [23], guide foils [24] and so on.For the other, called active control, energy requires to be injected into the flow as momentum injections [25][26][27], moving-wall [28], synthetic jet actuators [29], suction and blowing [30][31][32][33][34] and so on.
The Lorentz force, one of the active approaches, has been subjected to various studies since the 1960s.In the recent years, the Lorentz force has attracted more attention due to its promising applications in engineering fields.Crawford and Karniadakis [35] has numerically investigated that the Lorentz force can eliminate the flow separation when the flow past a stationary cylinder, and the suppressing effect of the Lorentz force has been confirmed by Weier et al. [36] with both experiments and calculations.Later, in the cases of Kim and Lee [37] and Posdziech and Grundmann [38], it is found that both of the continuous and pulsed Lorentz forces can suppress the force fluctuation and stabilize the flow.Recently, optimal and closed-loop control have been developed by Zhang et al. [39][40][41] aiming to improve the control efficiency of the cylinder wake, and the VIV of the shear incoming flow was also investigated preliminarily [42].However, there has not been discussion in the literature on the control of VIV by Lorentz forces in shear flow.
In this paper, control of VIV with Lorentz forces for the shear flow has been numerically investigated.The stream function-vorticity equations, the initial and boundary conditions, distribution of hydrodynamic force and the cylinder motion equation are deduced in the exponential-polar coordinate with the coordinate at the moving cylinder.The Lorentz force can be classified into the field Lorentz force and the wall Lorentz force.On the other hand, the evolution of VIV starting from rest to vibration, and suppression are all presented.The mechanism of fluidcylinder interactions in the shear flow with different distributions of Lorentz forces is discussed in detail.

Governing Equations
A circular cylinder experiences time varying lift and drag, which are related to the vortex shedding, when placed in a flowing fluid.Thus, time varying vibration will occur when the cylinder is constrained to move on flexible supports, which is known as vortex-induced vibration (VIV).Moreover, the fluid around the cylinder is altered by this vibration, which affects the induced hydrodynamic forces in turn and the structure response is then changed.Therefore, this problem is associated with fully coupled fluid-structure interactions.
For control of VIV in an electrically low-conducting fluid, the actuators on the cylinder surface consists of two half cylinders mounted with alternating electrodes and magnets as shown in Figure 1.The momentum of the fluid round the cylinder surface is increased with the application of Lorentz force, which is directed parallel to the cylinder surface.In this way, the electro-magnetic force F can be written in the dimensionless form: where the superscript "*" refers to the dimensional form, no superscript refers to the dimensionless form.This can be written in dimensionless form [36,38] with F r = 0, 1 covered with actuatoron upper surface −1 covered with actuator on lower surface 0 elsewhere where r and θ represent polar coordinates, r and θ denote the components in r and θ directions, respectively.α is a constant, denoting the effective depth of Lorentz force in the fluid.The interaction parameter is termed as , with the current density j 0 , B 0 the magnetic field, ρ the fluid density, and a the cylinder radius.
The exponential-polar coordinates system (ξ, η) is introduced here defined as r = e 2πξ , θ = 2πη.Then, the stream function-vorticity equations in the dimensionless form, which express the flow considering an applied Lorentz force with the coordinate system attached on the moving cylinder, are termed as We need to mention that the above equations (Equations ( 2) and ( 3)) have the same forms as the equations in the absolute coordinate system.The stream function ψ is defined as , with u r and u θ indicating the velocity components in r and θ directions, respectively.Moreover, H = 4π 2 e 4πξ , Re = 2u ∞ a ν , u ∞ is the free-stream velocity, ν is the kinematic viscosity, and the dimensionless time is t = t * u ∞ a .The sketch of shear flow, which shows the change of the velocity in the cross-section plane of the cylinder, with a linear velocity profile u = u ∞ + Gy [43] over a cylinder in two-dimensional domain is shown in Figure 2, where u ∞ is the free-stream velocity at the center-line θ = 0, y is the coordinate in the lateral direction with y = 0 at the center of the cylinder, and G is the lateral velocity gradient.Defining the shear rate K as , a refers to the cylinder radius.Only the circumstance of a positive shear rate, i.e., 0 K > , needs to be discussed here, indicating that the flow velocity of the upper side prevails over that of the lower side.
Initially, the flow is regarded as inviscid.When the cylinder can only move in a cross flow direction, the initial flow field in the moving frame of reference can be described by Defining the shear rate K as K = 2Ga/u ∞ , a refers to the cylinder radius.Only the circumstance of a positive shear rate, i.e., K > 0, needs to be discussed here, indicating that the flow velocity of the upper side prevails over that of the lower side.
Initially, the flow is regarded as inviscid.When the cylinder can only move in a cross flow direction, the initial flow field in the moving frame of reference can be described by As for t > 0, the cylinder is constrained to vibrate along the transverse direction with the effect of the vortex shedding.Based on the Galilean velocity decomposition and the stream function definition, we have where the superscript " " denotes the absolute coordinate (an inertial frame of reference), and no superscript denotes the coordinate (a non-inertial frame of reference) which is attached on the cylinder moving with the velocity dt , where l is the cylinder displacement in the transverse direction.The relative angle of the incoming flow direction is defined as θ 0 = tan −1 dl(t) dt , then when ξ → ∞ , e 2πξ → 2sh(2πξ) , from Equation ( 5), we have which depends on the shear rate K and the vibration of cylinder, and and where H = 4π 2 .From Equation (7), ∂ 2 ψ ∂η 2 = 0 Thus, one finally obtains In addition, the applied Lorentz force has no relationship with the flow field, and involves two types which can be defined as the field Lorentz force F θ | ξ>0 and the wall Lorentz force F θ | ξ=0 .The field Lorentz force does not appear in any above equations, but acts as a source term affecting the boundary layer fluid and accordingly leads to the variations of hydrodynamic force.The wall Lorentz Appl.Sci.2017, 7, 61 5 of 20 force, however, is independent of the flow field due to the non-slip boundary and affects directly on the surface of cylinder.

Hydrodynamic Forces
Defining the net hydrodynamic force F θ acting on a cylinder as If the prime coordinate system indicates the absolute coordinate (the inertial frame of reference) in the previous reference, the shear stress C θ τ is written as On the cylinder surface, where Therefore, the shear stress involves two components denoted as C θ τF and C θ τV , where C θ τF is proportional to vorticity at the wall, whereas C θ τV induced by the cylinder motion in viscous flow, has no relationship with the vorticity field.
The pressure C θ p is termed as based on the definition [41] C θ p = where the pressure is P = p ρu 2 ∞ /2 with p the pressure of the flow field.Then, C θ p can be formulated further by following mathematical derivation.
From the momentum equations in the moving coordinate of reference, one obtains and Then, Here, pressure C θ p consists of C θ pF induced by the field Lorentz force, C θ pW induced by the wall Lorentz force and C θ pV induced by the inertial force.The hydrodynamic force is also regarded as a force consisting of drag force and lift force denoting the force components in the streamwise and the transverse directions, respectively.We have and C θ l = C θ p sin(2πη) + C θ τ cos(2πη) where the subscripts "d" and "l" denote the drag and lift force, respectively.
The total force is attained by integrating the force distribution function along the cylinder surface, by defining the dimensionless form , Then, the drag C d can be termed as where The lift C l is written as where Hence, where the first term on the right-hand side C lF , the so-called vortex-induced force, depends on the vorticity and the boundary vorticity flux on the surface of cylinder.The field Lorentz force N F θ | ξ>0 serves as a source to influences the vorticity field, in turn, to alternate C lF .The second term, C lW , is induced by wall Lorentz force, which has no relationship with flow field.The third term, called inertial force, depends on acceleration of cylinder and the fourth term, called viscous damping force, depends on Reynolds number and cylinder velocity.Therefore, the second to fourth terms have no relationship with the varying flow field.

Cylinder Responses
As the cylinder is constrained to experience VIV in the transverse direction, the equation of motion in the absolute coordinate (the inertial frame of reference) may be termed as [42] where m is the dimensionless mass; ς is the dimensionless structure damping; m vir is the virtual mass; and ω = 2π f , f is vortex shedding frequency.When the lock-in occurs, the vortex shedding frequency is synchronized with the natural frequency of cylinder and f n / f remains invariant.Furthermore, F l is the hydrodynamic force in the transverse direction.

Numerical Approach and Procedure for Fluid-Structure Coupling
The calculations are performed numerically.The detail process on numerical procedure of fluid-structure interaction is shown in Figure 3.At the beginning, based on the initial flow field described by Equation ( 4) and the boundary conditions Equations ( 5)-( 8), the lift force exerted on the cylinder can be obtained at t > t 1 by Equation (15).Then, the displacement and velocity of cylinder can be obtained from the motion Equation (17).Subsequently, the flow field is advanced to the next time step by the integration of Equations ( 2) and (3) according to the boundary conditions calculated for update, as does the control process with Lorentz force at t > t 2 .Therefore, the flow field, the hydrodynamic force, the cylinder motion and so on can be obtained in the whole fluid-structure interactiion process with this method.
Appl.Sci.2017, 7, 61 8 of 21 induced by wall Lorentz force, which has no relationship with flow field.The third term, called inertial force, depends on acceleration of cylinder and the fourth term, called viscous damping force, depends on Reynolds number and cylinder velocity.Therefore, the second to fourth terms have no relationship with the varying flow field.

Cylinder Responses
As the cylinder is constrained to experience VIV in the transverse direction, the equation of motion in the absolute coordinate (the inertial frame of reference) may be termed as [42] where m is the dimensionless mass; ς is the dimensionless structure damping; vir m is the virtual mass; and When the lock-in occurs, the vortex shedding frequency is synchronized with the natural frequency of cylinder and F is the hydrodynamic force in the transverse direction.

Numerical Approach and Procedure for Fluid-Structure Coupling
The calculations are performed numerically.The detail process on numerical procedure of fluid-structure interaction is shown in Figure 3.At the beginning, based on the initial flow field described by Equation ( 4) and the boundary conditions Equations ( 5)-( 8), the lift force exerted on the cylinder can be obtained at > by Equation (15).Then, the displacement and velocity of cylinder can be obtained from the motion Equation (17).Subsequently, the flow field is advanced to the next time step by the integration of Equations ( 2) and (3) according to the boundary conditions calculated for update, as does the control process with Lorentz force at 2 t t > .Therefore, the flow field, the hydrodynamic force, the cylinder motion and so on can be obtained in the whole fluid-structure interactiion process with this method.The exponential mapping in the radial direction allows us to work in a very large physical domain, so that we can avoid the well-known blockage effect (i.e., the effect of the size of apparatus or computational box).On the other hand, the grids near the cylinder are fine enough in a very small physical domain, so that the flow field can be described accurately.In the numerical calculations The exponential mapping in the radial direction allows us to work in a very large physical domain, so that we can avoid the well-known blockage effect (i.e., the effect of the size of apparatus or computational box).On the other hand, the grids near the cylinder are fine enough in a very small physical domain, so that the flow field can be described accurately.In the numerical calculations presented in this paper, the physical circular domain in polar coordinates is transformed into the rectangular (ξ, η) domain through the coordinate transformation (r, θ) → (ξ, η) .The computations presented in this paper are run on a mesh consisting of N ξ × N η = 400 × 256 grid points.
The Alternative-Direction Implicit (ADI) algorithm was used to solve the equation of vorticity transport.A Fast Fourier Transform (FFT) algorithm was used to integrate the equation of stream function.Solving Equation ( 16) using the Runge-Kutta method allows calculating the cylinder motion.For more details on the numerical method and validation of the code, refer to [39][40][41][42].The concrete procedure for simulating the coupling of fluid and structure is the same as [42].Moreover, the above numerical methods have the accuracy of second order in space and first order in time [42].The computational step sizes are ∆ξ = 0.004 and ∆η = 0.004 for all simulations appearing in the paper.The input parameters are as follows: density of fluid ρ = 1.0 × 10 3 kg/m 3 , kinematic viscosity ν = 1.0 × 10 −6 m 2 /s, free-stream velocity u ∞ = 7.5 × 10 −3 m/s, cylinder radius a = 1.0 × 10 −2 m, (so that Re = 2u ∞ a ν = 150, where the flow about the cylinder is fully laminar), density of cylinder ρ cyl = 2.6π × 10 3 kg/m 3 , and f = f n = 0.0675/s (so that ρ cyl /ρ = 2.6π).For VIVs in dense fluid, the structural damping is so small that it is negligible [44].In order to accentuate the effect of viscous damping force ( 4Re dl dt ), it may even be assumed zero (i.e., ς = 0).

Results
From the previous derivations, the Lorentz force is parallel to the cylinder surface along the flow direction, which leads to the acceleration of the boundary layer fluid and improves the capacity of the fluid for overcoming the adverse pressure gradient.Therefore, the flow separation is suppressed, which change the induced fluid forces in turn and subsequently the cylinder response is altered.Moreover, the definition of interaction parameter N is indicated in Equation ( 1), which represents the strength of Lorentz force.

Control of VIV with Symmetrical Lorentz Force
In order to describe the differences between the VIV behavior of the cylinder in shear flow and that in uniform flow, the periodical variation of vortex-induced vibration for different shear rate K at the steady VIV with Re = 150 in a shedding cycle are exhibited in Figure 4 by the shaded vorticity contours, where the red refers to the negative vortex, and blue the positive.The cross-hairs mark the equilibrium position of cylinder for shear rate K = 0.For convenience, the times at t = 0T/4, 1T/4, 2T/4 and 3T/4 in all the K cases are denoted by A, B, C and D, respectively, where T denotes one period of the cylinder oscillation.
The symmetrical flow field is broken due to the background vorticity, which is generated by shear flow that also causes the increase of upper vortex strength and the decrease of lower vortex strength.With the effect of shear flow, the separation point on the upper side of cylinder moves downstream due to the increase of fluid momentum on the upper side of cylinder while the separation point on the lower side of cylinder moves upstream due to the decrease of fluid momentum on the lower side of cylinder.The vortex street inclines toward the lower side and the inclination of vortex streets increase with the increasing shear rate K, as does the distance of two vortex rows.The equilibrium position of vibration cylinder shifts to the lower side due to the shear flow.It is obvious that the vortex shedding and the cylinder vibration are suppressed under the influence of symmetrical Lorentz force and the control effects increase with the increase of interaction parameter N. Despite the control, it is still observed that the front stagnation point moves to the upper side of cylinder and the wake shifts to the lower side, which generally occurs with the effect of shear incoming flow.The distributions of shear stress C θ τ with different values of interaction parameter N for the different stages of one cycle are depicted in Figure 7, where the shear rate K = 0.2.The symmetrical curve is broken due to the different strength of shear layers on the upper and lower sides, which is generated by shear flow.The boundary layer fluid is hastened by Lorentz force, leading to the increase of shear stress.In addition, the strength of shear stress increases with the increase of interaction parameter N.However, the shift of front stagnation point still exists and the shift amplitude of shear stress C θ τ decreases with the increase of Lorentz force (interaction parameter N) on a cycle.With the Lorentz force applied, the pressure on the surface of vibrating cylinder is composed of three parts where C θ pW is the pressure induced by the wall Lorentz force, C θ pF is the pressure induced by vortex shedding and C θ pV is the pressure affected by the inertial force.The effects of interaction parameter N on the distributions of C θ pW which has no relationship with flow field and cylinder vibration, are discussed firstly based on Figure 8 to examine the VIV control.The curve with positive values is symmetrical about the line θ = 180 • .Therefore, the wall Lorentz force only causes the drag decrease, without the effect on the lift.
symmetrical curve is broken due to the different strength of shear layers on the upper and lower sides, which is generated by shear flow.The boundary layer fluid is hastened by Lorentz force, leading to the increase of shear stress.In addition, the strength of shear stress increases with the increase of interaction parameter N .However, the shift of front stagnation point still exists and the shift amplitude of shear stress  With the Lorentz force applied, the pressure on the surface of vibrating cylinder is composed of three parts  The distributions of pF θ C induced by vortex shedding at different stages of one cycle with different values of interaction parameter N are depicted in Figure 9 where the shear rate 0.2 K = , and A, B, C, and D correspond to those in Figure 6.As the stagnation point shifts to the upper side with the effect of shear flow, the pressure distribution shifts along the clockwise direction as well, The distributions of C θ pF induced by vortex shedding at different stages of one cycle with different values of interaction parameter N are depicted in Figure 9 where the shear rate K = 0.2, and A, B, C, and D correspond to those in Figure 6.As the stagnation point shifts to the upper side with the effect of shear flow, the pressure distribution shifts along the clockwise direction as well, which then leads to the increase and decrease of pressure on the upper and lower side, respectively.Obviously, these basic features of VIV in shear flow maintains for the small symmetrical Lorentz force.The pressure on the leeward decreases rapidly with the effect of Lorentz force, leading to the increase of drag and the decrease of the lift oscillating amplitude, in turn, as well as the decline of cylinder vibration.However, the curves are asymmetrical about θ = 180 • due to the shear flow even if Lorentz force is large enough.
Appl.Sci.2017, 7, 61 13 of 21 which then leads to the increase and decrease of pressure on the upper and lower side, respectively.Obviously, these basic features of VIV in shear flow maintains for the small symmetrical Lorentz force.The pressure on the leeward decreases rapidly with the effect of Lorentz force, leading to the increase of drag and the decrease of the lift oscillating amplitude, in turn, as well as the decline of cylinder vibration.However, the curves are asymmetrical about  The inertial force C θ pV , resulting from the acceleration of the cylinder, has influence on the pressure distributions as well.The distributions of C θ pV related with the inertial force for different values of interaction parameter N are depicted in Figure 10.When N = 0, the additional lift generated by the background vortex caused by the shear incoming flow leads to the acceleration d 2 l(t) dt 2 at Time B being larger than that at Time D. Namely, the inertial force at Time B is larger than that at Time D. When N > 0, the inertial force decreases with the increase of the values of Lorentz force while the inertial force at Time B is still larger than that at Time D. The lift-drag phase diagrams with different values of interaction parameter N for shear rate 0.2 K = are depicted in Figure 11.The lift-drag curve shrinks with the increase of the values of Lorentz force, which indicates the decrease of drag and lift vibration.Therefore, the amplitude of vibrating cylinder decreases.Moreover, the lift-drag curve (a Figure 8 shape at N = 0) is switched to a teardrop shape by increasing the interaction parameter N.For N = 0, the drag at Time C is larger than that at Time A due to the fact that the strength of upper vortex is larger than that of lower vortex with the effect of shear flow (shown in Figure 6) and then the pressure pF θ C on the cylinder leeward at Time C is smaller than that at Time A (shown in Figure 9), which leads to Point A and Point C separating in the lift-drag phase diagram.The flow field on the cylinder leeward is gradually dominated by the upper vortex with the increase of Lorentz force.At Time C, the shear layer of upper side is accelerated under the effect of pressure side which leads to the increase of the strength of upper vortex, then the decrease of pressure pF θ C on the cylinder leeward and subsequently the increase of drag.The distance between Point A and Point C of lift-drag curve is increased, which leads to the lift-drag phase diagram switching to a teardrop shape gradually.Furthermore, the curve shifts from the left to the right, which implicates the increase of drag.The additional lift still exists under the effect of shear flow.The lift-drag phase diagrams with different values of interaction parameter N for shear rate K = 0.2 are depicted in Figure 11.The lift-drag curve shrinks with the increase of the values of Lorentz force, which indicates the decrease of drag and lift vibration.Therefore, the amplitude of vibrating cylinder decreases.Moreover, the lift-drag curve (a Figure 8 shape at N = 0) is switched to a teardrop shape by increasing the interaction parameter N.For N = 0, the drag at Time C is larger than that at Time A due to the fact that the strength of upper vortex is larger than that of lower vortex with the effect of shear flow (shown in Figure 6) and then the pressure C θ pF on the cylinder leeward at Time C is smaller than that at Time A (shown in Figure 9), which leads to Point A and Point C separating in the lift-drag phase diagram.The flow field on the cylinder leeward is gradually dominated by the upper vortex with the increase of Lorentz force.At Time C, the shear layer of upper side is accelerated under the effect of pressure side which leads to the increase of the strength of upper vortex, then the decrease of pressure C θ pF on the cylinder leeward and subsequently the increase of drag.The distance between Point A and Point C of lift-drag curve is increased, which leads to the lift-drag phase diagram switching to a teardrop shape gradually.Furthermore, the curve shifts from the left to the right, which implicates the increase of drag.The additional lift still exists under the effect of shear flow.The lift-drag phase diagrams with different values of interaction parameter N for shear rate 0.2 K = are depicted in Figure 11.The lift-drag curve shrinks with the increase of the values of Lorentz force, which indicates the decrease of drag and lift vibration.Therefore, the amplitude of vibrating cylinder decreases.Moreover, the lift-drag curve (a Figure 8 shape at N = 0) is switched to a teardrop shape by increasing the interaction parameter N.For N = 0, the drag at Time C is larger than that at Time A due to the fact that the strength of upper vortex is larger than that of lower vortex with the effect of shear flow (shown in Figure 6) and then the pressure pF θ C on the cylinder leeward at Time C is smaller than that at Time A (shown in Figure 9), which leads to Point A and Point C separating in the lift-drag phase diagram.The flow field on the cylinder leeward is gradually dominated by the upper vortex with the increase of Lorentz force.At Time C, the shear layer of upper side is accelerated under the effect of pressure side which leads to the increase of the strength of upper vortex, then the decrease of pressure pF θ C on the cylinder leeward and subsequently the increase of drag.The distance between Point A and Point C of lift-drag curve is increased, which leads to the lift-drag phase diagram switching to a teardrop shape gradually.Furthermore, the curve shifts from the left to the right, which implicates the increase of drag.The additional lift still exists under the effect of shear flow.The evolution of the cylinder displacement from still to steady vibration, then to a new steady state with symmetric Lorentz force (N = 0.8) for K = 0.2 is shown in Figure 12.The release of transverse confinement occurs at t = 446, which leads to the displacement of cylinder increasing gradually under the effect of lift.Moreover, the equilibrium position which separates from the point l/a = 0 and shifts to the lower side.When t = 640, the steady vibration is reached.When the symmetric Lorentz force is initiated at time t 2 = 650, a well-developed VIV is performed, and the cylinder displacement will decrease over time.However, the equilibrium position shifts because shear flow still exists.The variation of vorticity of VIV before and after the application of symmetric Lorentz force (N = 0.8) for K = 0.2 is shown in Figure 13 where time B i in this figure corresponds to that in Figure 12 while the cylinder arrives at the lowermost position.The cylinder starts to vibrate with the effect of lift as the confinement of cylinder is released.With the energy transferring from the fluid to the cylinder, there is an increase in the cylinder oscillations.The corresponding vortex patterns are described as B 1 ∼ B 4 .The cylinder vibrates steadily as the total cylinder energy develops into an equilibrium state.The corresponding vortex pattern is described as B 5 .When the symmetric Lorentz force is attached on the cylinder at time t 2 = 650, the cylinder vibration and the fluid separation are suppressed at some extent ( B 6 ∼ B 8 ) while the wake vortex is inclined to the lower side.The vibration amplitude varies significantly with the interaction parameter N , as depicted in Figure 15.Notably, the amplitude of cylinder vibration decreases with the increase of N, and the cylinder will finally rest when the interaction parameter N is large enough.The vibration amplitude varies significantly with the interaction parameter N , as depicted in Figure 15.Notably, the amplitude of cylinder vibration decreases with the increase of N, and the cylinder will finally rest when the interaction parameter N is large enough.The vibration amplitude varies significantly with the interaction parameter N, as depicted in Figure 15.Notably, the amplitude of cylinder vibration decreases with the increase of N, and the cylinder will finally rest when the interaction parameter N is large enough.The vibration amplitude varies significantly with the interaction parameter N , as depicted in Figure 15.Notably, the amplitude of cylinder vibration decreases with the increase of N, and the cylinder will finally rest when the interaction parameter N is large enough.

Control of VIV with Asymmetrical Lorentz Force
For a shear flow past a cylinder, the shift of front stagnation point and additional lift, pointing to lower side for K > 0, are induced under the effect of background vorticity, even if symmetrical Lorentz forces are applied.Therefore, the equilibrium position of cylinder controlled by symmetrical Lorentz forces departs from its initial position, as mentioned in Figure 12.However, the lift C lL generated by asymmetrical Lorentz forces can be used to counteract the additional lift, so that the total lift C l = 0 and then the cylinder shifts to the initial position.
The evolution of the cylinder displacement before and after the application of asymmetric Lorentz force (upper surface N = 3, lower surface N = 2) in a shear flow with K = 0.2 is shown in Figure 16.When the asymmetric Lorentz force is initiated at time t 2 = 650 when the VIV is well-developed, the lift C lL pointing to the upper side is generated, which can counteract the additional lift to suppress the vibration of cylinder and lead to the equilibrium position of cylinder shifting back to the upper side.Finally, the cylinder is steady on the initial position.

Control of VIV with Asymmetrical Lorentz Force
For a shear flow past a cylinder, the shift of front stagnation point and additional lift, pointing to lower side for 0 K > , are induced under the effect of background vorticity, even if symmetrical Lorentz forces are applied.Therefore, the equilibrium position of cylinder controlled by symmetrical Lorentz forces departs from its initial position, as mentioned in Figure 12   C on the surface of cylinder with the asymmetric Lorentz force is depicted in Figure 18.Due to the higher flow speed on the upper surface, the shear stress on the upper side prevails over that on the lower side obviously.The vorticity of VIV with the asymmetric Lorentz force is shown in Figure 17.The wake suppressed completely by the Lorentz force inclines to the lower side with the influence of shear flow.

Control of VIV with Asymmetrical Lorentz Force
For a shear flow past a cylinder, the shift of front stagnation point and additional lift, pointing to lower side for 0 K > , are induced under the effect of background vorticity, even if symmetrical Lorentz forces are applied.Therefore, the equilibrium position of cylinder controlled by symmetrical Lorentz forces departs from its initial position, as mentioned in Figure 12.However, the lift lL C generated by asymmetrical Lorentz forces can be used to counteract the additional lift, so that the total lift   C on the surface of cylinder with the asymmetric Lorentz force is depicted in Figure 18.Due to the higher flow speed on the upper surface, the shear stress on the upper side prevails over that on the lower side obviously.The distribution of shear stress C θ τ on the surface of cylinder with the asymmetric Lorentz force is depicted in Figure 18.Due to the higher flow speed on the upper surface, the shear stress on the upper side prevails over that on the lower side obviously.C on the lower side is larger than that on the upper side.Thus, the wall Lorentz force results in the amplification of lift with the direction pointing to the upper side and the drag reduction (thrust generated).C on the surface of cylinder with the asymmetric Lorentz force is depicted in Figure 20.With the effect of asymmetric Lorentz force, the curve moves down.The pressure on the upper surface prevails over that on the lower surface, while the decrease of pressure on the leeward side is sharper than that on the windward side.Therefore, the lift decreases and the drag increases with the effect of field Lorentz force, which is opposite with the effect of wall Lorentz force.However, the total effect is dominated by the wall Lorentz force.The distribution of pressure coefficient C θ pW with the asymmetric Lorentz force is shown in Figure 19.The value of C θ pW is positive and the maximum is achieved at θ = 180 • .Meanwhile, the C θ pW on the lower side is larger than that on the upper side.Thus, the wall Lorentz force results in the amplification of lift with the direction pointing to the upper side and the drag reduction (thrust generated).C on the lower side is larger than that on the upper side.Thus, the wall Lorentz force results in the amplification of lift with the direction pointing to the upper side and the drag reduction (thrust generated).The distribution of pF θ C on the surface of cylinder with the asymmetric Lorentz force is depicted in Figure 20.With the effect of asymmetric Lorentz force, the curve moves down.The pressure on the upper surface prevails over that on the lower surface, while the decrease of pressure on the leeward side is sharper than that on the windward side.Therefore, the lift decreases and the drag increases with the effect of field Lorentz force, which is opposite with the effect of wall Lorentz force.However, the total effect is dominated by the wall Lorentz force.The distribution of C θ pF on the surface of cylinder with the asymmetric Lorentz force is depicted in Figure 20.With the effect of asymmetric Lorentz force, the curve moves down.The pressure on the upper surface prevails over that on the lower surface, while the decrease of pressure on the leeward side is sharper than that on the windward side.Therefore, the lift decreases and the drag increases with the effect of field Lorentz force, which is opposite with the effect of wall Lorentz force.However, the total effect is dominated by the wall Lorentz force.

Conclusions
With exponential-polar coordinates attached on a moving cylinder, we have deduced the related equations considering the electro-magnetic force for the shear flow, i.e., the stream functionvorticity equations, the initial and boundary conditions, the hydrodynamic forces on the cylinder surface, and the cylinder motion equation together with the mathematical expressions of the lift force l C .The applied Lorentz force was not dependent on the flow field and it involves two categories: the field Lorentz force 0 F θ ξ > and the wall Lorentz force 0 F θ ξ = .As a source term, the field Lorentz force affected the flow field in the boundary layer, which leads to the variations of hydrodynamic force.The wall Lorentz force, however, is independent of the flow field due to the non-slip boundary and affects directly on the surface of cylinder.
The momentum of the fluid round the cylinder surface is increased by Lorentz force, which overcomes the effect of the "adverse" pressure gradient.Therefore, the separation points move downstream, and even disappear on the cylinder surface.With the application of symmetrical Lorentz forces, the symmetric field Lorentz force can increase the drag, suppress the flow separation, decay the lift fluctuation, and, in turn, suppress the VIV, whereas the wall Lorentz force decreases the drag only, i.e. no effect on the lift.With the application of asymmetrical Lorentz forces besides above-mentioned effects, the field Lorentz force can strengthen additional lift (negative value) induced by shear flow, whereas the wall Lorentz force can counteract the additional lift, which dominates the total effect.Therefore, it is notable that the asymmetrical Lorentz force, which suppresses the lift vibration and enhances the lift value, can be applied to overcome the lift loss that is caused by the shear flow.
From the above discussion, the aims for the vibration suppression, drag reduction and lift amplification have been obtained with application of Lorentz force.More complicated geometries, such as wing sections, can be controlled with application of this approach.The optimum performance can be obtained with changing the position of actuators in the applications based on the separation points, vortexes, the suction and pressure sides and so on.In addition, the value of Lorentz force varies with time according to the instantaneous flow field, which can be applied to control varying flow conditions, such as dynamically-changing angles of attack.

Conclusions
exponential-polar coordinates attached on a moving cylinder, we have deduced the related equations considering the electro-magnetic force for the shear flow, i.e., the stream function-vorticity equations, the initial and boundary conditions, the hydrodynamic forces on the cylinder surface, and the cylinder motion equation together with the mathematical expressions of the lift force C l .The applied Lorentz force was not dependent on the flow field and it involves two categories: the field Lorentz force F θ | ξ>0 and the wall Lorentz force F θ | ξ=0 .As a source term, the field Lorentz force affected the flow field in the boundary layer, which leads to the variations of hydrodynamic force.The wall Lorentz force, however, is independent of the flow field due to the non-slip boundary and affects directly on the surface of cylinder.
The momentum of the fluid round the cylinder surface is increased by Lorentz force, which overcomes the effect of the "adverse" pressure gradient.Therefore, the separation points move downstream, and even disappear on the cylinder surface.With the application of symmetrical Lorentz forces, the symmetric field Lorentz force can increase the drag, suppress the flow separation, decay the lift fluctuation, and, in turn, suppress the VIV, whereas the wall Lorentz force decreases the drag only, i.e. no effect on the lift.With the application of asymmetrical Lorentz forces besides above-mentioned effects, the field Lorentz force can strengthen additional lift (negative value) induced by shear flow, whereas the wall Lorentz force can counteract the additional lift, which dominates the total effect.Therefore, it is notable that the asymmetrical Lorentz force, which suppresses the lift vibration and enhances the lift value, can be applied to overcome the lift loss that is caused by the shear flow.
From the above discussion, the aims for the vibration suppression, drag reduction and lift amplification have been obtained with application of Lorentz force.More complicated geometries, such as wing sections, can be controlled with application of this approach.The optimum performance can be obtained with changing the position of actuators in the applications based on the separation points, vortexes, the suction and pressure sides and so on.In addition, the value of Lorentz force varies with time according to the instantaneous flow field, which can be applied to control varying flow conditions, such as dynamically-changing angles of attack.

Figure 1 .
Figure 1.Lorentz force on the cylinder surface.

Figure 1 .
Figure 1.Lorentz force on the cylinder surface.

Figure 2 .
Figure 2. Sketch of shear flow over circular cylinder.

Figure 2 .
Figure 2. Sketch of shear flow over circular cylinder.

Figure 3 .
Figure 3.The detailed process of the numerical procedure of fluid-structure interaction.

Figure 3 .
Figure 3.The detailed process of the numerical procedure of fluid-structure interaction.

Figure 5 .
Figure 5.The variation of

Figure 5 .
Figure 5.The variation of

Figure 5 .
Figure 5.The variation of C dF ∼ C lF phase diagram with shear rate K.

CFigure 7 .C
Figure 7. Distributions of shear stress θ τ C on the surface of cylinder with different values of interaction parameter N for shear rate 0.2 K = : (a) Time A; (b) Time B; (c) Time C; and (d) Time D.

Figure 7 .Figure 7 .
Figure 7. Distributions of shear stress C θ τ on the surface of cylinder with different values of interaction parameter N for shear rate K = 0.2: (a) Time A; (b) Time B; (c) Time C; and (d) Time D.

C
is the pressure induced by the wall Lorentz force, pF θ C is the pressure induced by vortex shedding and pV θ C is the pressure affected by the inertial force.The effects of interaction parameter N on the distributions of pW θ C which has no relationship with flow field and cylinder vibration, are discussed firstly based on Figure 8 to examine the VIV control.The curve with positive values is symmetrical about the line 0 180 θ = .Therefore, the wall Lorentz force only causes the drag decrease, without the effect on the lift.

Figure 8 .
Figure 8. Distributions of pressure coefficient pW θ C with Lorentz force controls.

Figure 8 .
Figure 8. Distributions of pressure coefficient C θ pW with Lorentz force controls.

Figure 9 .C
Figure 9. Distribution of pF θ C on the surface of cylinder with different values of interaction parameter N for shear rate 0.2 K = : (a) Time A; (b) Time B; (c) Time C; and (d) Time D.

Figure 9 .
Figure 9. Distribution of C θ pF on the surface of cylinder with different values of interaction parameter N for shear rate K = 0.2: (a) Time A; (b) Time B; (c) Time C; and (d) Time D.

Figure 10
Figure 10.Distributions of pV θ C

Figure 11 .
Figure 11.Lift-drag phase diagrams with different values of interaction parameter N for shear rate 0.2 K = .

Figure 10 .
Figure 10.Distributions of C θ pV on cylinder surface with K = 0.2 for different values of interaction parameter N.

Figure 11 .
Figure 11.Lift-drag phase diagrams with different values of interaction parameter N for shear rate 0.2 K = .

Figure 11 .
Figure 11.Lift-drag phase diagrams with different values of interaction parameter N for shear rate K = 0.2.
gradually under the effect of lift.Moreover, the equilibrium position which separates from the point 0 l a = and shifts to the lower side.When 640 t = , the steady vibration is reached.When the symmetric Lorentz force is initiated at time 2 650 t =, a well-developed VIV is performed, and the cylinder displacement will decrease over time.However, the equilibrium position shifts because shear flow still exists.

Figure 12 . 4 B 8 BFigure 12 .
Figure 12.Evolution of the cylinder displacement with the symmetric Lorentz force ( 0.8 N = ) for Appl.Sci.2017, 7, 61 15 of 21 gradually under the effect of lift.Moreover, the equilibrium position which separates from the point 0 l a = and shifts to the lower side.When 640 t = , the steady vibration is reached.When the symmetric Lorentz force is initiated at time 2 650 t =, a well-developed VIV is performed, and the cylinder displacement will decrease over time.However, the equilibrium position shifts because shear flow still exists.

Figure 14 .
Figure 14.Time evolutions of lift lF C and drag dF C for VIV development and suppression with

Figure 15 .
Figure 15.Limiting amplitude of oscillating cylinder displacement after control versus the interaction parameter N for 0.2 K = .

Figure 13 .
Figure 13.(B 1 -B 8 ) Instantaneous vortex patterns of VIV before and after the application of symmetric Lorentz force (N = 0.8) for K = 0.2.

Figure 13 .
Figure 13.(B1-B8) Instantaneous vortex patterns of VIV before and after the application of symmetric Lorentz force ( 0.8 N = ) for 0.2 K = .Time evolutions of lift-drag phase diagram for VIV in a developing and then suppressed process with 0.8 N = and 0.2 K = are shown in Figure 14.The closed curve 1 1 1 1 1 A B C D A , which represents the stationary cylinder, is turned right at 180° as the cylinder starts to vibrate.Then, Point A and Point C are separated until VIV is well-established.However, Point A and Point C do not coincide any longer, where the phase diagram

Figure 14 .
Figure 14.Time evolutions of lift lF C and drag dF C for VIV development and suppression with

Figure 15 .
Figure 15.Limiting amplitude of oscillating cylinder displacement after control versus the interaction parameter N for 0.2 K = .

Figure 14 .
Figure 14.Time evolutions of lift C lF and drag C dF for VIV development and suppression with the symmetric Lorentz force (N = 0.8) for K = 0.2.

Figure 14 .
Figure 14.Time evolutions of lift lF C and drag dF C for VIV development and suppression with

Figure 15 ..Figure 15 .
Figure 15.Limiting amplitude of oscillating cylinder displacement after control versus the interaction parameter N for 0.2 K = .Figure 15.Limiting amplitude of oscillating displacement after control versus the interaction parameter N for K = 0.2.
. the lift lL C generated by asymmetrical Lorentz forces can be used to counteract the additional lift, so that the total lift 0 l C = and then the cylinder shifts to the initial position.The evolution of the cylinder displacement before and after the application of asymmetric Lorentz force (upper surface 3 N = , lower surface 2 N = ) in a shear flow with 0.2 K = is shown in Figure 16.When the asymmetric Lorentz force is initiated at time 2 650 t = when the VIV is well-developed, the lift lL C pointing to the upper side is generated, which can counteract the additional lift to suppress the vibration of cylinder and lead to the equilibrium position of cylinder shifting back to the upper side.Finally, the cylinder is steady on the initial position.

Figure 16 .
Figure 16.Evolution of the cylinder displacement before and after application of Lorentz force (upper surface 3 N = , lower surface 2 N = ) in shear flow for 0.2 K = .

Figure 17 .
Figure 17.The vorticity of VIV with the Lorentz force (upper surface 3 N = , lower surface 2 N = ) for 0.2 K = .

Figure 16 .
Figure 16.Evolution of the cylinder displacement before and after application of Lorentz force (upper surface N = 3, lower surface N = 2) in shear flow for K = 0.2.

0 lC
= and then the cylinder shifts to the initial position.The evolution of the cylinder displacement before and after the application of asymmetric Lorentz force (upper surface 3 N = , lower surface 2 N = ) in a shear flow with 0.2 K = is shown in Figure 16.When the asymmetric Lorentz force is initiated at time 2 650 t = when the VIV is well-developed, the lift lL C pointing to the upper side is generated, which can counteract the additional lift to suppress the vibration of cylinder and lead to the equilibrium position of cylinder shifting back to the upper side.Finally, the cylinder is steady on the initial position.

Figure 16 .
Figure 16.Evolution of the cylinder displacement before and after application of Lorentz force (upper surface 3 N = , lower surface 2 N = ) in shear flow for 0.2 K = .

Figure 17 .
Figure 17.The vorticity of VIV with the Lorentz force (upper surface 3 N = , lower surface 2 N = ) for 0.2 K = .

Figure 17 .
Figure 17.The vorticity of VIV with the Lorentz force (upper surface N = 3, lower surface N = 2) for K = 0.2.

Figure 18 .
Figure 18.The distribution of shear stress θ τ C on the cylinder surface with the asymmetric Lorentz

Figure 19 .
Figure 19.The distributions of pressure coefficient pW θ C with the asymmetric Lorentz force (upper

Figure 18 .
Figure 18.The distribution of shear stress C θ τ on the cylinder surface with the asymmetric Lorentz force (upper surface N = 3, lower surface N = 2) for shear rate K = 0.2.

Figure 18 .
Figure 18.The distribution of shear stress θ τ C on the cylinder surface with the asymmetric Lorentz

Figure 19 .
Figure 19.The distributions of pressure coefficient pW θ C with the asymmetric Lorentz force (upper

Figure 19 .
Figure 19.The distributions of pressure coefficient C θ pW with the asymmetric Lorentz force (upper surface N = 3, lower surface N = 2) for shear rate K = 0.2.

Figure 20 .
Figure 20.The distribution of pressure induced by vortex pF θ C on the surface of cylinder with the

Figure 20 .
Figure 20.The distribution of pressure induced by vortex C θ pF on the surface of cylinder with the asymmetric Lorentz force (upper surface N = 3, lower surface N = 2) for shear rate K = 0.2.