Assessing the Influence of RMS and VDV on Analysis of Human Perception of Vibrations in Buildings Caused by Selected Sources of Traffic

Featured Application: The studies presented in the article are useful for designing secondary vibration isolation. They also show that relying solely on indications from one method of assessing the impact of vibrations on people in buildings, a potential investor or later a manager may be exposed to complaints from residents of buildings located near transportation investments. Abstract: This research paper delves into the nuanced effects of traffic-induced vibrations on human comfort and perception within residential and commercial buildings. By prioritizing the influence of vehicle types—including metro trains, trams, and cars—over their speed or mass, the study presents a novel perspective on addressing vibrational comfort. Conducted in the urban context of Warsaw’s metro line construction, this investigation employs a rigorous methodology, utilizing both the Root Mean Square (RMS) and Vibration Dose Value (VDV) analytical methods to quantify vibrational impacts. The findings illuminate the distinct contributions of various transportation modes to the perceived vibrations, offering significant insights into the complex relationship between the Human Perception of Vibration Index (HPVI) and VDV values. It underscores the necessity of integrating a multifaceted consideration of vehicle type, operational dynamics, and urban infrastructure in the strategic planning and design of buildings. Such a holistic approach is essential for mitigating the adverse effects of transportation-induced vibrations, thereby enhancing the quality of life and well-being of urban inhabitants.


Introduction
Vibrations that propagate from the ground into buildings can pose significant challenges not only to the structural integrity of these buildings but also to the well-being and comfort of their occupants.These challenges extend beyond more physical harm or the accelerated deterioration of building materials; they intrude into the daily lives of individuals, affecting their comfort and, in severe instances, their health.Residents and users of buildings may find themselves contending with a range of adverse effects, from minor annoyances to serious health implications.
One of the primary concerns with ground-borne vibrations is their impact on the structural health of buildings.Continuous exposure to vibrations can lead to the development of micro-cracks in the building's foundation and walls, compromising the building's overall stability and safety.Moreover, the vibratory motion can accelerate the wear and tear of construction materials, leading to premature aging of the building and necessitating more frequent repairs and maintenance, thus increasing the financial burden on property owners and managers.This effect becomes worse against multi-hazard occurrences, for example, due to additional vibrations induced by the wind [1].
Beyond the structural implications, the human impact of these vibrations cannot be overstated.Inside the buildings, vibrations can disturb the peace and quiet that occupants expect from their living and working environments.The physical sensation of vibrations can be particularly bothersome, disrupting concentration and relaxation.In extreme cases, the persistent presence of low-frequency vibrations-ranging from 5 to 25 Hz, which coincides with the resonant frequencies of human internal organs-can lead to more severe health issues.Individuals may experience sleep disturbances, which in turn can contribute to a range of psychological and physical health problems, including headaches, chronic fatigue, and even neurotic states.The evidence from a broad array of studies [2][3][4][5] supports these findings, highlighting the need for further investigation and action.In [2], references to the impact of vibrations on human sleep quality can be found, while [3] presents a more medical approach to the influence of vibrations on heart rate.Ref. [4] highlights the particular impact of low-frequency vibrations on human health, whereas [5] provides a comprehensive view of the impact of transportation vibrations as a detrimental factor to both physical and mental health.Despite the considerable body of research on this topic and the existence of normative standards designed to mitigate the impact of vibrations, there remains a gap in our full understanding and management of this issue.The subjective nature of vibration perception-how vibrations are experienced differently by individuals-poses a significant challenge to developing universal guidelines and solutions.This variability in perception is influenced by several factors, including an individual's health, sensitivity to motion, and even psychological predisposition to stress or anxiety caused by environmental conditions.The evolving understanding of the effects of ground-borne vibrations on humans and structures has led to changes and updates in both national and international regulatory standards, such as those encapsulated in ISO standards [6,7].These adjustments reflect the ongoing research and growing awareness of the need for comprehensive approaches to vibration management.They aim to provide clearer guidelines for the construction of buildings and the development of urban areas, ensuring that both the physical integrity of structures and the health and comfort of their occupants are safeguarded.
People can perceive transportation-originated vibrations in two distinct ways: active and passive.The active mode of vibration perception relates to situations where individuals themselves generate vibrations, mainly applicable to machine operators or drivers.In contrast, passive reception of vibrations occurs when individuals have no influence over the source of the vibrations.The difference between active and passive reception of vibrations is vividly illustrated by the example of a car with a driver and a passenger.The driver, steering the car, anticipates turns or road irregularities that they decide to navigate through.This anticipation allows the driver to mentally and physically prepare for the upcoming vibrations, leading to a more controlled and less startling experience.The driver's active role in generating and anticipating vibrations results in a perception that is often less bothersome or disturbing.This preparation might involve bracing for impact, adjusting the vehicle's speed, or strategically choosing a path that minimizes discomfort from vibrations.On the other hand, for the passenger, these same situations are unexpected and uncontrolled.The passenger does not have the same awareness or control over the vehicle's movements, making each bump, turn, or vibration a sudden and possibly unsettling experience.This lack of anticipation and control exemplifies the passive reception of vibrations.Passengers are subjected to movements and vibrations generated by the vehicle without any prior knowledge or the ability to mitigate their impact.This can result in a more intense perception of discomfort, as the element of surprise can exacerbate the physical sensation of the vibrations.The psychological aspect of anticipation plays a significant role in the active and passive reception of vibrations.When individuals are actively involved in the generation of vibrations, their preparedness and control over the situation can significantly reduce the perceived intensity and discomfort of those vibrations.In contrast, the absence of control and predictability in passive reception can lead to heightened sensitivity and discomfort.In summary, the perception of transportationoriginated vibrations differs markedly between active participants, like drivers or machine operators, who can anticipate and control their exposure, and passive recipients, such as passengers, who experience these vibrations without forewarning or control.
The results of research on the impact of vibrations caused by transportation means on people who passively receive these vibrations have been presented in many scientific works [8][9][10][11][12][13].In [8] authors analyze the road traffic influence on the dynamic structural behavior of the building and human perception of vibration caused by busy roadways.Meanwhile, in [9], the authors explore the impact of vibrations caused by trains on individuals perceiving these vibrations passively.Foundations for the current understanding of the impact of vibrations on humans in buildings were laid out in [10].The analysis focused on the influence of building vibrations on the perceptibility of vibrations by individuals, regardless of their source.The contemporary approach to the impact of vibrations on individuals, combined with the influence of noise, can be found in [11].Similarly, in [12], not only noise but also vibrations, in this case caused by railway traffic, were indicated as stress-inducing factors.In [13] once again, the focus was on the influence of transportation vibrations, but there was also an attempt to predict the behavior of the floor under the influence of vibrations.A modern approach was also applied in [14], where the propagation of waves in the ground was also considered.These analyses cover various aspects, including the intensity of vibrations, their frequency, and the impact of these vibrations on the well-being and health of individuals.However, the available literature lacks a global, comprehensive approach to the issue, which would allow for a full understanding of the scale and specificity of the impact of transportation vibrations on people in buildings.
In many studies, detailed results regarding the impact of vibrations on humans are presented without proper context, which complicates the drawing of general conclusions.Furthermore, there is often a lack of information about the source of the vibrations, which is crucial for understanding the mechanisms of their action and potential impact on people.This is a significant oversight, as the source of vibrations is fundamentally important for their characteristics.For example, vibrations caused by vehicles moving on railroads are characterized by greater intensity and are therefore more perceptible to people in buildings than vibrations caused by vehicles on roadways.This difference in perception and impact on people stems from differences in transport technology, the type of substrate, and the construction of infrastructure supporting various types of transport.
Considering the passive reception of transportation-type vibrations by people in buildings and the not entirely comprehensive methodology of assessing the impact of vibrations on people, it has been observed that the existing methodology associated with the RMS (Root Mean Square) method may be insufficient in certain cases.In the recorded signal originating from transportation sources, so-called peaks can occur, for example, when there are irregularities on the road or track, and these peaks are more perceptible than the stable passage of a vehicle near a building.Therefore, in many national and international standards, an auxiliary measure called the Vibration Dose Value (VDV) has been introduced to assess the impact of vibrations on people in buildings.The Vibration Dose Value, by incorporating the fourth power in its formula, does not lose these peaks but, in fact, makes them more prominent in the signal.The aspect that unites all methods of assessing the impact of vibrations on people in buildings is the reference of analysis results to the posture of a person present in a room.In assessing the impact of vibrations on people, three positions of human vibration reception are considered.In the sitting and standing positions, a person receives vibrations through the feet or the seating surface, in such a way that the "z" axis, which runs along the spine, is the vertical axis, while the "x" axis (back to front) and "y" axis (side to side) are horizontal axes.In the lying position, the entire body surface receives vibrations in such a way that the "z" axis becomes the horizontal direction, and the "x" axis becomes vertical.The perception of vibrations by humans varies depending on the direction of their action in such a way that for frequencies below 4 Hz, horizontal vibrations are more perceptible than vertical ones, while above this frequency, the situation is reversed, and it is the vertical vibrations that are more perceptible.Information about the purpose of the room, the time of occurrence of the vibrations, and their nature are included in the value of the correction factor "n" in the RMS method, which should be used to multiply the vibration perception threshold curves to obtain curves representing the comfort assurance lines in a given measurement situation.In VDV, they are included in the value itself in the table.
The article presents the results of 24 h measurements conducted during the construction of the metro line in Warsaw.The analysis of the results was carried out using both the classical RMS method and the VDV method.Interesting events related to the passage of metro trains, tram cars, and automobile traffic on a nearby road were recorded.

The Measurement Methodology and a General Description of the Conducted Measurements
The revised standard [15] includes guidelines pertaining to the proper execution and analysis of measurements of the impact of vibrations on people in buildings.The recommendations cover both equipment requirements and the selection of measurement points, as well as the analysis of the recorded signal itself.
The buildings selected for analysis were located within the so-called dynamic impact zone (Table 1).
Table 1.The range of the dynamic impact zone in assessing the impact of vibrations on people in buildings.

Source of Vibration The Scope of the Dynamic Impact Zone [m]
Tramway ≤25 Road ≤25

Shallow underground ≤40
An extremely important aspect of measuring the impact of vibrations on people in buildings is the selection of measurement point locations.In this area, the normative records of different countries show some differences.According to the ISO standard [7], vibrations transmitted to the human body should be measured on the surface between the body and that surface.This is an imprecise provision.Meanwhile, the ISO standard [6], in relation to the selection of the measurement point, requires that the measurement of vibrations transmitted to the human body be conducted in the middle of rigid surfaces.This more precise provision is due to the scope of application of the ISO [6] standard, which contains requirements mainly relating to vibrations of general impact.The British standard [16] in this area is much more lenient.It also indicates the center of the room intended for the permanent stay of people, but the range of the zone in which measurements of the impact of vibrations on people can be conducted ranges from 1/3 to 2/3 of the length/width of the ceiling.The measurements carried out as part of the research included in this work were conducted according to the Polish standard [15].The measurement points were located at least in one room on the highest floor, located as close as possible to the source of vibrations.Clarification is needed regarding the choice of a measurement point on the ceiling of the highest floor, given information that the highest level of vibrations generated by metro train passages occurs on the ceilings of the lowest floors.In the studies conducted in connection with the subject of this work, the goal was not to perform a diagnosis but to study the mutual relations between assessment parameters.The measurement point was located in the geometric center of the room.
During the measurements, vibration accelerations were recorded, which was associated with the ease of assessing the impact of vibrations on people using this parameter.During the conducted measurements, devices that should enable the correct registration of the signal from 1 Hz, and even below this value, were significant.During the measure-ments, seismic sensors of type 393B12 PCB Piezotronics were used, featuring a nominal sensitivity of 10 V/g, a measuring range of ±0.5 g, and a frequency range spanning from 0.1 Hz to 1 kHz.For signal recording purposes, the LMS Scadas Mobile recorder with integrated ICP ® standard signal conditioning systems for each channel was employed.The use of ICP ® conditioners allows for the utilization of long cables, significantly facilitating measurement tasks in buildings with large dimensions or when measurements necessitate considerable distances between measurement points and the recording station.This analyzer offers real-time recording capabilities for each channel while preserving high signal dynamics across the entire frequency spectrum.The measurement, although in most cases the vertical direction plays a decisive role, should be conducted simultaneously in three orthogonal directions: the "X" direction is taken in all measurements perpendicular to the excitation, the "Y" direction parallel, and the "Z" direction is the vertical direction.
According to the standard [15], the use of a measurement disc is recommended, which should have a weight of at least 30 kg and a diameter of 30 cm [15] (Figure 1).The signal registration should enable the recording of frequencies in the range from 1 to 120 Hz, so that after applying a low-pass filter, frequencies up to 80 Hz could be included in the assessment.
During the measurements, vibration accelerations were recorded, which was associated with the ease of assessing the impact of vibrations on people using this parameter.During the conducted measurements, devices that should enable the correct registration of the signal from 1 Hz, and even below this value, were significant.During the measurements, seismic sensors of type 393B12 PCB Piezotronics were used, featuring a nominal sensitivity of 10 V/g, a measuring range of ±0.5 g, and a frequency range spanning from 0.1 Hz to 1 kHz.For signal recording purposes, the LMS Scadas Mobile recorder with integrated ICP ® standard signal conditioning systems for each channel was employed.The use of ICP ® conditioners allows for the utilization of long cables, significantly facilitating measurement tasks in buildings with large dimensions or when measurements necessitate considerable distances between measurement points and the recording station.This analyzer offers real-time recording capabilities for each channel while preserving high signal dynamics across the entire frequency spectrum.The measurement, although in most cases the vertical direction plays a decisive role, should be conducted simultaneously in three orthogonal directions: the "X" direction is taken in all measurements perpendicular to the excitation, the "Y" direction parallel, and the "Z" direction is the vertical direction.
According to the standard [15], the use of a measurement disc is recommended, which should have a weight of at least 30 kg and a diameter of 30 cm [15] (Figure 1).The signal registration should enable the recording of frequencies in the range from 1 to 120 Hz, so that after applying a low-pass filter, frequencies up to 80 Hz could be included in the assessment.Determining the duration of vibrations is a separate issue.The standard [15] stipulates that the duration of vibrations is defined by the interval during which the value of vibration acceleration amplitudes does not fall below 0.2 of the maximum amplitude value in the recorded waveform.The ISO standard [6], primarily used for measuring general-character vibrations, requires that the signal recording time be at least 30 min.The standard [7] contains a provision regarding the duration of vibrations, stating that the recorded signal should suffice to ensure reasonable statistical accuracy.This definition is Determining the duration of vibrations is a separate issue.The standard [15] stipulates that the duration of vibrations is defined by the interval during which the value of vibration acceleration amplitudes does not fall below 0.2 of the maximum amplitude value in the recorded waveform.The ISO standard [6], primarily used for measuring general-character vibrations, requires that the signal recording time be at least 30 min.The standard [7] contains a provision regarding the duration of vibrations, stating that the recorded signal should suffice to ensure reasonable statistical accuracy.This definition is very broad and imprecise, while the duration of vibrations significantly affects the signal analysis results, especially regarding the widely used and recommended RMS method in the work [7].In the German standard [17], analysis is carried out in cycles lasting 30 s each, after which data from the cycles are averaged.The measurements described in this work were performed in accordance with the standard [15].
The last issue related to the analysis of measurement data is the sampling frequency of the recorded signal, which, according to Nyquist's criterion [18], should adhere to the principle that the highest frequency recorded in the signal (f N ) is half the sampling frequency (f S ) (Formula (1)): This means that for a cutoff frequency f N = 120 Hz, the sampling frequency should be at least f S = 240 Hz.In practice, this minimum is set at 2.5 times the highest recorded frequency, which means that in the case of the impact of vibrations on people, the sampling frequency should be at least 300 Hz.Of course, the higher the f S value, the better the quality of the results, which is why in the analyses described in this work, a frequency of 1024 Hz was used.

The Root Mean Square (RMS) Method
The Root Mean Square (RMS) method, introduced already in the first edition of the ISO standard, has its physical interpretation, which is the energy of vibrations.The RMS value effectively describes vibrations because it contains information about the RMS components of vibrations across the entire range of frequencies considered.
The effective (RMS) value a RMS of vibration acceleration, is defined by the formula: where: T-duration time [s], a(t)-vibration acceleration [m/s 2 ].In practical measurements of the impact of vibrations on individuals in buildings, the RMS value of accelerations presented in 1/3 octave bands is used.This provides information not only about exceeding the threshold values of vibration perceptibility but also about the frequency band in which this exceedance occurred.This is particularly useful in building design because it then allows for "retuning" the structure of the floor or even the building in such a way as to avoid exceedances in specific frequency bands.
The RMS method, known as the fundamental method in ISO [6], stipulates that studies regarding the impact of vibrations on people in buildings should always include measurement results in RMS values.Due to the ease of interpretation of results presented using this method, many researchers employ it [19][20][21][22], and it has also been incorporated into the majority of standards in various countries.In [19], for instance, the impact of the speed of passing trains on building structures as well as on the perceptibility of vibrations by people was analyzed.In [20], the influence of vibrations induced by wind was determined, while works [21] and Ref. [22] constitute a synthesis of the impact of transportation vibrations on people residing in buildings.Work [21] serves as a kind of general compendium, whereas [22] focuses on the influence of vibrations from roads and railways.
In assessing the impact of vibrations on people in buildings conducted according to the RMS method, factors such as the room's purpose, the time of day when vibrations occur, the nature and repeatability, as well as the direction of vibrations and the position of the human body receiving vibrations in the room, are taken into account.
In the revised Polish standard [15], a new index has been introduced to express the assessment result of the impact of vibrations on people in buildings.This index, called the Human Perception of Vibration Index (HPVI), in relation to vibrations transmitted to humans in the "z" direction, can be calculated using the formula: where: a RMS -the root mean square value of vibration accelerations obtained from the analysis, a z -the root mean square value of vibration accelerations equal to the vibration perceptibility threshold for humans in the "z" direction in the same frequency band in which a RMS was determined.
The numerical value of the index supplemented with information about the center frequency of the band in which it was determined serves as a complement to the information obtained using the RMS method, presented in 1/3-octave bands, in the form of a graph.The HPVI not only informs about the exceeding of the vibration perceptibility threshold but also about the value of this exceedance.It should be noted that the result of the RMS method is illustrated in a graph on a logarithmic scale, which often causes problems in interpreting the requirement for ensuring necessary comfort.However, the graph along with information about the HPVI value provides more complete information.Figure 2 provides an example (from the analyzed building) of assessing the impact of vibrations on people with the illustration of the HPVI index.
In the revised Polish standard [15], a new index has been introduced to express the assessment result of the impact of vibrations on people in buildings.This index, called the Human Perception of Vibration Index (HPVI), in relation to vibrations transmitted to humans in the "z" direction, can be calculated using the formula: where: aRMS-the root mean square value of vibration accelerations obtained from the analysis, az-the root mean square value of vibration accelerations equal to the vibration perceptibility threshold for humans in the "z" direction in the same frequency band in which aRMS was determined.
The numerical value of the index supplemented with information about the center frequency of the band in which it was determined serves as a complement to the information obtained using the RMS method, presented in 1/3-octave bands, in the form of a graph.The HPVI not only informs about the exceeding of the vibration perceptibility threshold but also about the value of this exceedance.It should be noted that the result of the RMS method is illustrated in a graph on a logarithmic scale, which often causes problems in interpreting the requirement for ensuring necessary comfort.However, the graph along with information about the HPVI value provides more complete information.Figure 2 provides an example (from the analyzed building) of assessing the impact of vibrations on people with the illustration of the HPVI index.The RMS analysis of the vibrogram caused by the passage of the metro train did not indicate a violation of the conditions for ensuring vibrational comfort for people in the room.However, an exceedance of the vibration perceptibility threshold was observed.In the example analysis shown in Figure 2, the exceedance of the threshold measured by the HPVI was HPVI = 1.28 at a frequency of 40 Hz.

The Vibration Dose Value (VDV) Method
The best additional method for assessing the impact of vibrations on people in buildings in the case of sudden changes in acceleration, known as peaks in the recorded signal, is the Vibration Dose Value (VDV) method.This method is primarily used for The RMS analysis of the vibrogram caused by the passage of the metro train did not indicate a violation of the conditions for ensuring vibrational comfort for people in the room.However, an exceedance of the vibration perceptibility threshold was observed.In the example analysis shown in Figure 2, the exceedance of the threshold measured by the HPVI was HPVI = 1.28 at a frequency of 40 Hz.

The Vibration Dose Value (VDV) Method
The best additional method for assessing the impact of vibrations on people in buildings in the case of sudden changes in acceleration, known as peaks in the recorded signal, is the Vibration Dose Value (VDV) method.This method is primarily used for general and local vibrations that actively affect humans.Its sensitivity to the occurrence of peak values in the recorded signal arises from the formula used to calculate it, where vibration acceleration is raised to the fourth power: The transformation of the signal using Equation ( 4) results in the Vibration Dose Value (VDV) being expressed in units of m/s 1.75 .The procedure for determining the VDV value is similar in essence to the procedure used in the RMS method.However, the problem arises at the very beginning, where after applying the appropriate correction filter (values available in standards [23,24], or [25]), it is necessary to introduce weighting values corresponding to the directions of vibrations.According to standard [23], weighting values assigned to the directions of vibration reception by humans should be applied.Standard [24] allows for the use of the so-called combined weight when assessing the impact of vibrations on people in buildings.There are still differences in weighting values for the same directions in various standards.This is evident when comparing information from two standards, which were the first to introduce the VDV method, namely the British standard [26] and ISO [6].Both standards show differences in weighting values in the vertical direction, while the differences in the horizontal directions are minimal and result from the accuracy of determining the provided values.In the analyses conducted in connection with this study, according to the Polish standard [25], weighting functions were used for the "z" and "x" and "y" directions.The weighting function values specified in ISO [6] were applied because the Polish standard does not provide them.
Table 2 presents threshold values for the probability of complaint occurrence according to the appendix of the Polish standard [15].

The Analysed Building
The building where the series of measurements were conducted is located in Warsaw, at Zamoyskiego Street.It is a five-story building constructed using traditional masonry technology (see Figure 3).The building was erected before World War II.Klein-type slabs were used for the floors.It is situated at a distance of 9 m from the edge of the roadway and approximately 20 m from the tram line (measured from the nearest tram rail) and is directly above the metro tunnel (see Figure 4).The building was erected before World War II.Klein-type slabs were used for the floors.It is situated at a distance of 9 m from the edge of the roadway and approximately 20 m from the tram line (measured from the nearest tram rail) and is directly above the metro tunnel (see Figure 4).The building was erected before World War II.Klein-type slabs were used for the floors.It is situated at a distance of 9 m from the edge of the roadway and approximately 20 m from the tram line (measured from the nearest tram rail) and is directly above the metro tunnel (see Figure 4).The measuring point was located on the fourth floor, in a residential room facing the roadway and the tram tracks, according to the norm [25], and was situated in the geometric center of the ceiling (see Figure 5).Accelerations were measured in three orthogonal directions (X, Y, Z).The measuring point was located on the fourth floor, in a residential room facing the roadway and the tram tracks, according to the norm [25], and was situated in the geometric center of the ceiling (see Figure 5).Accelerations were measured in three orthogonal directions (X, Y, Z).

Results of Analysis
As a result of background dynamic measurements, 12 events were recorded originating from: the tram line (8 events) and the roadway (4 events).However, during post-construction measurements, 11 events related to metro train passages were recorded.In total, 23 events were subject to RMS/MTVV and VDV analysis.

Results of Analysis
As a result of background dynamic measurements, 12 events were recorded originating from: the tram line (8 events) and the roadway (4 events).However, during Appl.Sci.2024, 14, 3688 10 of 17 post-construction measurements, 11 events related to metro train passages were recorded.In total, 23 events were subject to RMS/MTVV and VDV analysis.

The Results of RMS Analysis
The recorded signal was analyzed according to the methodology described in Section 2 of this study.Out of the 23 recorded events, the threshold of vibration perceptibility by people in buildings was exceeded in five cases.Three exceedances of the perceptibility threshold occurred for metro train passages, accounting for approximately 27% of all metro train passages recorded on the site.Two exceedances of the perceptibility threshold occurred for roadway passages, which in this case constituted 50% of all passages recorded from that road.In the case of passing trams, no exceedance of the vibration perceptibility threshold by people was observed.
Below are examples of RMS analysis of individual events in 1/3-octave bands with the appropriate waveform (Figure 6-heavy truck passage, Figure 7-tramway passage, Figure 8-metro train passage).From the information provided in Figure 6, it can be inferred that the recorded vibrations do not violate the conditions for ensuring necessary comfort, but they are noticeable to individuals in the room.The threshold of vibration perception is exceeded for two frequencies: 12.5 Hz and 16 Hz, as better illustrated by the results given in Table 3, relating to the values of the HPVI.The passage of trams did not cause any exceedance of the threshold of vibration perception by people in any of the recorded events.Table 3. HPVI value with the middle frequency in 1/3 octave band for an example event (heavy truck passage in Figure 6).

HPVI [-]
Center Frequency of 1/3 Octave Band [Hz] 1.72 12.5 1.49 16.0 The RMS analysis of the vibrogram caused by the passage of the metro train did not reveal any violation of the conditions for ensuring vibrational comfort to people in the rooms.However, exceedances of the vibration perception threshold occurred.In the example shown in Figures 3 and 4, the exceedance measured by the HPVI indicator was HPVI = 1.28 at a frequency of 40 Hz.In this example, compared to vibrations caused by passages on the roadway, vibrations caused by metro train passages shifted the frequency spectrum towards higher values.From the information provided in Figure 6, it can be inferred that the recorded vibrations do not violate the conditions for ensuring necessary comfort, but they are noticeable to individuals in the room.The threshold of vibration perception is exceeded for two frequencies: 12.5 Hz and 16 Hz, as better illustrated by the results given in Table 3, relating to the values of the HPVI.The passage of trams did not cause any exceedance of the threshold of vibration perception by people in any of the recorded events.Table 3. HPVI value with the middle frequency in 1/3 octave band for an example event (heavy truck passage in Figure 6).

HPVI [-]
Center Frequency of 1/3 Octave Band [Hz] 1.72 12.5 1.49 16.0 The RMS analysis of the vibrogram caused by the passage of the metro train did not reveal any violation of the conditions for ensuring vibrational comfort to people in the rooms.However, exceedances of the vibration perception threshold occurred.In the example shown in Figures 3 and 4, the exceedance measured by the HPVI indicator was HPVI = 1.28 at a frequency of 40 Hz.In this example, compared to vibrations caused by passages on the roadway, vibrations caused by metro train passages shifted the frequency spectrum towards higher values.Based on the RMS analysis, it can be concluded that in 22% of the events, there was an exceeding of values corresponding to the thresholds of vibration perception by people in buildings.

The Results of VDV Analysis
The same events analyzed using the RMS method were subjected to VDV analysis.The duration of the events ranged from 11 to 19 s.The results of the VDV analysis along with the collective summary of HPVI indicators calculated in the RMS analysis are presented in Table 4.
Values that exceed the thresholds defined by the Polish standard [15] for the perception of vibrations by people in buildings (WODL > 1.0) or correspond to a low probability of complaints from residents during the daytime (VDV > 0.2) are marked in yellow.
For the purpose of comparing the results obtained by the RMS method and the VDV method, the following assumptions were made: -A low probability of complaints is compared with exceeding the threshold of vibration perception by people, - The possible occurrence of complaints is compared with the level of requirements for ensuring necessary vibrational comfort.
Based on the VDV method research, fewer events were found in which there was a low probability of resident complaints.These are two events related to subway train passages.Vibrations generated by tram passages are imperceptible.Based on the results of the assessment performed using the VDV method, it can be stated that 18% of events caused by subway train passages result in a low probability of complaints.Based on the measurement results, an attempt was made to analyze the correlation between two methods of determining the impact of vibrations on people in buildings: RMS (in the form of the HPVI index) and VDV.The result of this analysis is shown in Figure 9. Based on the measurement results, an attempt was made to analyze the correlation between two methods of determining the impact of vibrations on people in buildings: RMS (in the form of the HPVI index) and VDV.The result of this analysis is shown in Figure 9.The correlation between HPVI and VDV is equal to 0.67 which suggests a strong correlation between HPVI index and VDV value, but not too strong for exact prediction of one of the factors knowing the other.
The regression equation for the relationship between HPVI and VDV is: (5) The correlation between HPVI and VDV is equal to 0.67 which suggests a strong correlation between HPVI index and VDV value, but not too strong for exact prediction of one of the factors knowing the other.
The regression equation for the relationship between HPVI and VDV is: This equation indicates that for every unit increase in VDV, HPVI increases by approximately 2.92 units, starting from a base value of 0.44 when VDV is zero.This suggests a strong positive linear relationship between these two variables, confirming the moderate to strong correlation previously discussed.
The descriptive statistics for HPVI and VDV across different types of vehicles show differences: For HPVI: - These differences suggest that the type of vehicle has an impact on both HPVI and VDV measurements, with metro trains generally showing higher values and tramways showing lower values on average.Heavy trucks, though only represented by a single measurement, show notably high VDV.This analysis indicates that vehicle type does affect vibration impact measurements, with specific types of vehicles potentially causing more significant vibrations and discomfort.

Discussion
Although there are few holistic studies on the impact of transportation vibrations on people in buildings, i.e., those receiving vibrations passively, articles in which only one type of passing vehicle is studied also allow for comparison of results.In article [27], the effect of heavy goods vehicles (HGVs) is examined, showing that different types of vehicles have varying impacts, similar to the discussion on metro trains, buses, and trucks.In [28], the impact of tram speeds passing near a residential building on the residents' perception of vibrations was studied.It was found that the speed of the tram does not necessarily translate into vibrational comfort in rooms located near the tramway.Similar conclusions can be drawn from our analyses when comparing the travel time of trams with the VDV or HPVI values.This suggests that tram speed, much like the tram type, has a complex relationship with the vibrational comfort experienced inside buildings close to tram lines.This nuanced understanding underscores the importance of considering various factors beyond speed alone in efforts to minimize the impact of vibrations on residents.
A very interesting study can be found in [29], which is an in-depth analysis of the influence of tram traffic-induced vibration on buildings damaged by earthquakes, particularly in the context of the Zagreb 2020 earthquake.It explores various aspects of vibration impacts, including the tram type, velocity, and proximity to the buildings, and how these factors contribute to the propagation of existing cracks or cause new damage to the already earthquake-affected structures.Both our analysis and the document underscore the significant role of vehicle type in influencing vibration levels.Just as different types of vehicles (buses, metro trains, trams) were found to have varying impacts on HPVI and VDV, the document further specifies tram types, highlighting how specific tram models contribute differently to vibration levels and potentially to the damage extent of buildings.
The metro train passage is always studied when complaints from residents appear, as occurred in [30].Articles focus mostly on the diagnosis of noise and vibrations which appeared due to metro train passages.They focus on how to design buildings located near the metro.
The document [31] focuses on a comprehensive study of how traffic-induced vibrations affect residential buildings and their occupants, with a specific case study in Istanbul, one of the world's most populous and traffic-congested cities.The research includes surveys of building occupants' perceptions of vibrations, measurements of ground vibrations induced by trains, and numerical modeling of typical residential buildings to assess their responses to these vibrations.Similar to our analysis, Erkal's study highlights the significant role of vehicle type (especially trains) in influencing vibration levels and their perception by residents.This aligns with our findings on the variable impact of different types of vehicles on HPVI and VDV measurements.
Although there are no comprehensive studies that consider various types of vehicles passing near buildings where people passively receive transportation-induced vibrations, it can be observed from many research results that the type of vehicle is not insignificant when considering vibrational comfort.In addition, a further investigation is planned by considering multi-hazard effects (i.e., wind-induced vibrations on high-rise buildings) estimated through CFD simulations of [32].

Conclusions
Based on analyses made in the article, conclusions could be given as follows:

•
Relationship between HPVI and VDV: A positive correlation observed between HPVI and VDV (0.67) indicates the possibility of qualitatively predicting the magnitude of one variable based on the other.Knowing one variable allows us to predict the other with some probability.• The regression equation, HPVI = 2.92 * VDV + 0.44: Although the correlation is not very high, based on the above equation, it could be the predicted value of VDV knowing the HPVR ratio, which could be interesting, especially in the context of archival data • Influence of vehicle type on human perception of vibration in buildings: It could be seen that the heavier the vehicle is, the higher the influence on the people, especially when adding in the roughness of the road • In terms of VDV, another aspect that emerges is the duration of the vehicle's passage.This factor is not insignificant for the results of this analysis.It does not have as much influence on the RMS value.Therefore, it appears that the VDV value is affected by both the vehicle type and the length of its passage.To explore this, more passages of both buses and heavy trucks would be needed.

Figure 2 .
Figure 2. Illustration of HPVI value based on an example of RMS analysis during the metro train passage.

Figure 2 .
Figure 2. Illustration of HPVI value based on an example of RMS analysis during the metro train passage.

18 Figure 3 .
Figure 3.The view of the building's eastern elevation.

Figure 3 .
Figure 3.The view of the building's eastern elevation.

Figure 3 .
Figure 3.The view of the building's eastern elevation.

Figure 4 .
Figure 4.The location of the building in relation to specific sources of transportation vibrations.

Figure 4 .
Figure 4.The location of the building in relation to specific sources of transportation vibrations.

18 Figure 5 .
Figure 5.The sketch of the location of the vibration reception point by people in the analyzed building.

Figure 5 .
Figure 5.The sketch of the location of the vibration reception point by people in the analyzed building.

18 Figure 6 .
Figure 6.RMS analysis of heavy truck passage.Figure 6. RMS analysis of heavy truck passage.

Figure 6 .
Figure 6.RMS analysis of heavy truck passage.Figure 6. RMS analysis of heavy truck passage.

Figure 8 .
Figure 8. RMS analysis of metro train passage.

Figure 8 .
Figure 8. RMS analysis of metro train passage.

Figure 9 .
Figure 9. Correlation between HPVI and VDV values in analyzed building.

Figure 9 .
Figure 9. Correlation between HPVI and VDV values in analyzed building.

Table 2 .
The values of VDV for assessing the probability of complaints from people in buildings.

Table 4 .
The VDV values for individual events and the maximum HPVI values in the events.