Modelling of the Luminance Coefficient in the Light Scattered by a Mineral Mixture Using Machine Learning Techniques

: The primary objective of the research and analysis reported in this article was to determine an effective method for predicting the luminance coefficient of the mineral mixture for asphalt concrete and stone mastic asphalt. The luminance of the mineral mixture determines the final luminance value of the surface. Predicting the luminance coefficient quickly will significantly improve the mineral–asphalt mix design efficiency in selecting aggregates that meet functional requirements and increase the brightness of the surface. The research process consisted of two stages. The first stage covered modelling the Qd luminance coefficient of aggregate, taking into account its petrographic analysis. The second fundamental stage, based on the research of the first stage, concerned the modelling of the luminance coefficient of the mineral mixture, taking into account the percentage share of a given component, its grain size, and its photometric properties. An effective technique of reinforced trees was used for modelling. As a result of its application, a model match to experimental data was achieved at the level of 87%. It has also been shown that the greatest impact on increasing the luminance coefficient of the mineral mixture was the use of light aggregate (quartzite sandstone or limestone) with a grain size of 2/5 in quantities > 40% or 8/11 in quantities > 60%. Furthermore, the quartzite sandstone aggregates with a grain size of 5/8 had the highest efficiency in lightening the mineral mixture. However, the use of basalt aggregates of the same fraction significantly worsened the photometric properties of the mineral mixture. An important element of the research was also to indicate that the mineralogical composition of the aggregate is crucial for an accurate assessment of its luminance coefficient.


Introduction
According to the nomenclature used in European countries, light surfaces are those in which light aggregates and synthetic binders have been used, either colourless or in light colours, caused by the presence of the appropriate pigment.On the other hand, brightened surfaces are those in which traditional asphalts have been used as binders, while the aggregates are from the light group.Bright surfaces are defined as surfaces whose wear layer visually gives the impression of a bright surface.Invariably, in these types of solutions, the aggregate itself [1] is an important element.The International Commission on Illumination (CIE) [2] introduced the concept of luminance in 1982 to evaluate the brightness of surfaces.As a result of this decision, many methods of assessing this parameter have emerged.The purpose of illuminating roads, evaluated by luminance coefficients q, was the need to improve the visibility of objects and traffic participants on the road while minimising driver discomfort.The assessment of road surface luminance is complex and still requires the refinement of measurement methods [3].CIE introduced the R class system, according to which, each surface is classified into one of four classes from R1 to R4.Each of the four classes has a defined light reflection array (r-table) containing a reduced luminance coefficient [4].Unfortunately, the R classification is based on measurements from the 1960s and 1970s, and it should be taken into account that there have been changes in the technology of making asphalt surfaces (mma) and the requirements for macrotexture, and new types of asphalt aggregates [5] have been introduced.
A fundamental fact, increasingly noticeable in scientific publications and industry articles, is that bright surfaces heat up less during periods of intense sunlight and provide a higher contrast of the road profile compared to the roadside.It should not be forgotten that a very important element of road illumination is also the reduction of the amount of energy required to ensure adequate visibility at night.In this aspect, the amount of energy consumed by lighting is about 1.3% used by road lighting in the EU [6].However, the following question remains: what should be considered when lightening the surface?The reflection of a light beam from the surface of the road is a function of the physical state of the road and its nature, as well as the direction of the light beam and observation conditions [5].Different surfaces may have different reflection characteristics, even though the light intensity (measured in lux) is the same.Along with the change in reflective properties of road surfaces, the luminance of pavement will also change [7].Luminance is closely related to the type of aggregate and the state of surface wear.Reflection from the road surface is a function of the physical condition of the road and its character, as well as from the direction of its illumination and observation conditions [5].Different surfaces can have various reflection characteristics, which depend on the texture of the surface and its age, the materials making up the surface, the binding materials, and the ways of arrangement.The criterion for their acceptance still remains its operational features [8].Some light-coloured aggregates, such as quartzite sandstone, are aggregates obtained from rocks with acidic reactions with an elevated level of SiO 2 .They have high roughness coefficients that improve the anti-slip properties of the road surface [1,9].On the other hand, limestone aggregates, also of a light colour, are characterised by excellent adhesion to aggregates but have low roughness.Therefore, there are certain contradictions between the luminance of the aggregate and its potential for use.Despite the awareness of technologists that the type of material in the road surface affects the luminance of the surface, the phenomenon of light reflection is not directly taken into account when designing a mixture in work [10].This is mainly because there are no studies that would allow even approximate surface luminance value to be obtained based solely on data about the components of the mineral (mm) or mineral-asphalt (mma) mixture.
In the European Union, road lighting design is subject to regulations, with some deviations depending on the member country.For the region of Poland, the document [11] applies, which dictates the way lighting design takes into account the luminance coefficient Qo.The average luminance coefficient determines the weighted average of luminance coefficients for a certain area, in which the weights are the corresponding solid angle observation values.The average luminance factor, Qo, can be calculated or read from the r-table using the weighting factor procedure [12].It has been demonstrated that the average luminance coefficient Qo is strongly correlated with the average luminance produced on the road surface [5].In the 1990s, an alternative to Qo was introduced in the form of the luminance coefficient under diffuse lighting Qd.The alternative "brightness" parameter Qd, i.e., the luminance coefficient under diffuse illumination has been adopted for road marking; however, the Qo parameter is still used in the road surface classification system adopted for road lighting.The ability to accurately bring down the Qo values using r-tables to the Qd measure, which was to some extent included in the CIE document [13], is significant.The use of the Qd coefficient is possible due to the occurrence of a large correlation of the Qo coefficient with the average luminance generated on the road surface [5].
Unfortunately, there are still no mathematical models to effectively predict the luminance coefficient of the aggregate/asphalt mixture under diffuse illumination Qd.The existence of such a model or method of determination would allow the photometric properties of aggregates to be considered in the design of an asphalt mix.The Qin article [14] uses a linear regression model in the form of multiple regression to calculate perceived luminance in the tunnel interior lighting environment.It was pointed out that this type of regression technique is only applicable to the object under study, and its generalisation requires consideration of more factors.A reason for the low applicability of regression models based on the least squares method may be the observations in the work of Mazurek et al. [15].It indicates that the probability distribution of the luminance ratio is not normal.The fact that certain minerals are present means that the probability density function is not symmetrical and thus precludes the wider use of techniques based on parametric testing.Therefore, the data mining (DM) technique should be proposed as an effective method.This method provides simple regression or classification rules.However, it requires a large learning dataset as the error rate is not as controllable as it is when using experiment planning techniques [16].In addition, it also requires a full validation of the adopted model to be performed.Solutions to complex problems for which no mathematical model is known a priori are quite rare in road engineering using data mining techniques.Much more commonly, data mining techniques are so far mainly used to correctly predict the mechanical or physical properties of road materials.In the work of Rebelo et al. [17], a number of DM techniques were used to effectively predict the water resistance of mineral-asphalt mixtures.Gong et al. used DM to improve the rutting resistance of pavements [18].In contrast, Guo and Hao's work [19] used a random forest algorithm to assess pavement durability, using information on emerging damage.At the recent EATA 2023 conference in Gda ńsk (Poland), many works were presented in which machine learning techniques were used to identify dangerous road conditions.The work of Phan et al. [20] uses machine learning techniques (convolutional neural networks) to identify hazardous road surface conditions.Also, the estimation of the stiffness modulus was determined successfully using the FWD apparatus, taking into account a number of factors related to the measurement by means of artificial neural network (ANN) or support vector machine (SVM) techniques [21,22].The undoubted advantage of data mining (DM) methods is the consideration of a number of variables, both qualitative and quantitative.It can therefore be used to predict road performance parameters such as IRI [23] or skid resistance (SVR) [24].
There was much less interest in DM techniques for predicting the luminance coefficient of asphalt pavements and the aggregate itself.It should be noted that the evaluation of these parameters is complex and depends on the aggregate system, its origin, the macrotexture of the pavement, etc.The degree of complexity in the prediction of the luminance ratio means that classical methods based on the least squares method will be neither efficient nor effective.There are few studies that attempt to apply DM techniques to the assessment of luminance ratio.In their work, A. Del Corte-Valiente et al. used DM techniques to manage street lighting [25].In addition, the use of machine learning techniques is being used successfully to assess luminance phenomena in public buildings [26,27].
Despite advanced luminance ratio measurement methods, there are insufficient analyses of the extent of aggregate luminance ratio estimation in the world literature.The conclusions of the study, as reported in [15], indicate that the mineralogical composition of the aggregate is an important aspect in assessing the luminance level of the aggregate.The promising results have encouraged further work to evaluate the luminance coefficient of the mineral mix.The ability to develop an effective DM model for a mineral mix will allow the luminance ratio of a mineral-asphalt mix to be effectively predicted with only information on the luminance of its components.Therefore, the stated aim of the research was to determine the rules and relationships among mineralogy, aggregate grain size, the percentage of components, and the luminance of the mineral mixture using machine learning techniques.

Aggregate
Aggregate meeting the Polish requirements of WT-1/2014 [28] and PN-EN 13043 [29] for the construction of wearing layers of asphalt pavements was used in this study.Ag-gregates were taken using the quartering method.Aggregates for this study were selected using the quartering method.This is a collection of aggregates that are commonly available and used for pavement construction layers that came from areas of southern Poland.The petrographic identification, granulation, and origin of the aggregate are shown in Table 1.Table 1 also provides information on selected physical parameters of the aggregate that is intended for wearing courses.All aggregate types met the requirements of EN 13043 [30] specifying the properties of aggregates for use in bituminous mixtures.Selected characteristics are shown in Table 2.It was essential to collect the representative sample correctly.Aggregate samples were taken from an aggregate stockpile at five locations.The laboratory sample for testing was obtained using the quartering method following EN 933-1 [35].Limestones (white colour) had a high LA coefficient, which would limit their use for wearing courses.Quartzite is also a white-coloured aggregate.Its LA value was lower than that of the limestone aggregate.
On the other hand, this aggregate obtained the highest PSV value, which suggests its high resistance to polishing and, hence, a decrease in vehicle stopping distance.However, the quartzite aggregate has a low affinity with asphalt, which is a significant limitation when used in asphalt mixes.The guiding idea is to use an aggregate with a maximum PSV, minimum LA, and high adhesion to asphalt.None of the aggregates meet this criterion.Therefore, it is advisable to mix them, but there is a risk that many dark-coloured grains will be found in the mix composition, effectively reducing the mineral mix luminance.

Luminance Ratio
Road brightness and visibility under artificial light in Europe are related to the distribution of luminance and illumination on the road surface.The intensity of illumination on a road surface refers only to the amount of light reaching the surface, which does not indicate how bright the surface is.Illuminance (E) is the amount of incident light (luminous flux Φ) per unit area (A).The SI unit of illuminance is lux (lx).According to the SI system, illumination is expressed by Formula (1), as follows: Luminance, on the other hand, is defined as the luminance flux per unit projected area and is a function of the illuminance on the road and the reflectance characteristics of the road surface [37], according to Formula (2), as follows: where Φ is the luminance flux, A is the surface, Ω is the spatial noun, and θ denotes the angle between the direction of the solid angle Ω and the emitting normal or reflecting surface A. The geometry required to determine the luminance ratio is shown in Figure 1.
distribution of luminance and illumination on the ro illumination on a road surface refers only to the amoun which does not indicate how bright the surface is.Illu incident light (luminous flux Φ) per unit area (A).The SI According to the SI system, illumination is expressed by F

E dΦ dA
Luminance, on the other hand, is defined as the lum area and is a function of the illuminance on the road and t the road surface [37], according to Formula (2), as follows: where Φ is the luminance flux, A is the surface, Ω is the s angle between the direction of the solid angle Ω and the surface A. The geometry required to determine the lumina In summary, the reflectance of a surface field can be d q, which is defined as the luminance of the surface field L, reflection, divided by the illuminance of the surface pla Formula (3), as follows: The geometry of the luminance factor: α (angle of observation), β (angle between the plane of incidence and the plane of observation), γ (angle of incidence), and δ (angle between the planes of observation and the axis of the road on which the luminance factor q of the road surface is located depending on the observation point P [38]).
In summary, the reflectance of a surface field can be described by a luminance factor q, which is defined as the luminance of the surface field L, produced by illumination and reflection, divided by the illuminance of the surface plane of the field E according to Formula (3), as follows: The luminance factor q is measured in mcd•m −2  EN 1436 [39] defines Qd as the ratio of the luminance of a surface area under diffuse illumination in proportion to the illuminance at the surface plane.Qd is measured using the spectral distribution of illumination according to a standard illuminator representing daylight and an observation angle of 2.29 • representing a geometry (observation distance) of 30 m.A representation of the measurement of Qd is represented by the diagram below (Figure 2).

Diffuse Luminance Coefficient Qd and Surface Reflectance Coefficient RL
EN 1436 [39] defines Qd as the ratio of the luminance of a surface ar illumination in proportion to the illuminance at the surface plane.Qd is the spectral distribution of illumination according to a standard illumina daylight and an observation angle of 2.29° representing a geometry (obse of 30 m.A representation of the measurement of Qd is represented by th (Figure 2).Surface reflection is strong in situations corresponding to driving The usual bounce is strong in situations corresponding to riding wit Suitable light for a standard road configuration when confronted with dry conditions is assessed by optimising the lighting distribution function [4 reflectivity of a road surface traditionally depends on the averaged lumi Qo [12] and the mirrored reflectivity S1 [41].The average luminance e luminance factor Qo, although still used, is a parameter that is difficult t small space of a portable instrument.Therefore, from the 1990s onward was introduced to characterise the reflectivity of road markings in daylig lighting.Portable units are available and are used widely for road marki be applied to road surfaces.However, no portable instrument determ mirroring coefficient.The luminance factor Qd, used in this study, takes mirror effect, but to a lesser extent than Qo.Therefore, the Qd parameter as a reasonable approximation of the Qo value for determining the illum for road lighting design.The Qd factor is also relevant when daylighti twilight) [40].
The standardised luminance coefficient Qd for the pavement, assoc table, can be determined using laboratory methods from a cut sample under field conditions using a reflectometer or by modern digital techniques [42].It is worth mentioning that the maximum luminance that for a given area when the surroundings have a constant luminance L is 3 In contrast, a value of approximately Qd = 52 mcd⋅m −2 ⋅lx −1 is attrib pavements [41].This type of luminance factor determines daytime visibi Another measure of luminance is the surface reflectance RL (mc defined as the quotient of the luminance L of the marking surface in observation by the illuminance E in a plane perpendicular to the direction and to the area of that reflective surface.The definition of RL is very sim luminance ratio Qd and has the same unit.Typically, the surface reflectan Surface reflection is strong in situations corresponding to driving against the sun.The usual bounce is strong in situations corresponding to riding with the sun back.Suitable light for a standard road configuration when confronted with dry and wet surface conditions is assessed by optimising the lighting distribution function [40].The degree of reflectivity of a road surface traditionally depends on the averaged luminance coefficient Qo [12] and the mirrored reflectivity S1 [41].The average luminance expressed by the luminance factor Qo, although still used, is a parameter that is difficult to measure in the small space of a portable instrument.Therefore, from the 1990s onwards, the Qd factor was introduced to characterise the reflectivity of road markings in daylight or under road lighting.Portable units are available and are used widely for road markings and can also be applied to road surfaces.However, no portable instrument determines the precise mirroring coefficient.The luminance factor Qd, used in this study, takes into account the mirror effect, but to a lesser extent than Qo.Therefore, the Qd parameter can be regarded as a reasonable approximation of the Qo value for determining the illuminance required for road lighting design.The Qd factor is also relevant when daylighting is poor (e.g., twilight) [40].
The standardised luminance coefficient Qd for the pavement, associated with the r-table, can be determined using laboratory methods from a cut sample of the pavement under field conditions using a reflectometer or by modern digital image analysis techniques [42].It is worth mentioning that the maximum luminance that can be obtained for a given area when the surroundings have a constant luminance L is 318 mcd•m −2 •lx −1 .In contrast, a value of approximately Qd = 52 mcd•m −2 •lx −1 is attributed to "black" pavements [41].This type of luminance factor determines daytime visibility.
Another measure of luminance is the surface reflectance RL (mcd•m −2 •lx −1 ).It is defined as the quotient of the luminance L of the marking surface in the direction of observation by the illuminance E in a plane perpendicular to the direction of incident light and to the area of that reflective surface.The definition of RL is very similar to that of the luminance ratio Qd and has the same unit.Typically, the surface reflectance coefficient RL determines the reflectivity of pavement or horizontal markings illuminated by the light of vehicle lamps.It is also referred to as night visibility.It is important in the absence of road lighting.A diagram of its designation is shown in Figure 3.

Test Stand for Measuring the Luminance Ratio
The test form used to test the aggregate and mineral mixtures co orders of WT-2/2014 [43], according to which the stable test area should mm.In contrast, the void that is not to be measured should be filled material.The working area containing the aggregate was sized to match t of the retroreflectometer (LTL-X Mark II) and was 320 mm × 235 mm.sample was tested 5 times at different locations in the working area.Ano then taken from another location in the aggregate stockpile (series).Eac assessed using five series.As a result, for the determination of the coeffic were measured 25 times for each aggregate against each grain size.Each pre-compacted and levelled with a screed to obtain reference measurem The test stand is shown in Figure 4.

Test Stand for Measuring the Luminance Ratio
The test form used to test the aggregate and mineral mixtures complied with the orders of WT-2/2014 [43], according to which the stable test area should be 700 mm × 700 mm.In contrast, the void that is not to be measured should be filled with any rigid material.The working area containing the aggregate was sized to match the working area of the retroreflectometer (LTL-X Mark II) and was 320 mm × 235 mm.Each aggregate sample was tested 5 times at different locations in the working area.Another sample was then taken from another location in the aggregate stockpile (series).Each aggregate was assessed using five series.As a result, for the determination of the coefficient, Qd and RL were measured 25 times for each aggregate against each grain size.Each test sample was pre-compacted and levelled with a screed to obtain reference measurement conditions.The test stand is shown in Figure 4.  Road surfaces generally have RL values in the range of 10 to 30 mcd⋅m −2 ⋅lx −1 .In comparison, surfaces intended for road marking (containing glass spheres) can usually achieve at least RL = 150 mcd⋅m −2 ⋅lx −1 .

Test Stand for Measuring the Luminance Ratio
The test form used to test the aggregate and mineral mixtures complied with the orders of WT-2/2014 [43], according to which the stable test area should be 700 mm × 700 mm.In contrast, the void that is not to be measured should be filled with any rigid material.The working area containing the aggregate was sized to match the working area of the retroreflectometer (LTL-X Mark II) and was 320 mm × 235 mm.Each aggregate sample was tested 5 times at different locations in the working area.Another sample was then taken from another location in the aggregate stockpile (series).Each aggregate was assessed using five series.As a result, for the determination of the coefficient, Qd and RL were measured 25 times for each aggregate against each grain size.Each test sample was pre-compacted and levelled with a screed to obtain reference measurement conditions The test stand is shown in Figure 4.The test stand was set up to determine the luminance coefficient of aggregates and mineral mixtures.According to the Polish regulations contained in WT-2 [43] and PN-EN 1436 [39], the measurement of the luminance ratio should be carried out at an angle of 2.29° (equivalent to observing the road from a distance of 30 m from the position of a passenger car driver).The measurement field should be a rectangle measuring 185 mm x 50 mm, with an angular spread of ±0.17°.This requirement was met by the LTL-X Mark II device used to perform this study.The device allows two parameters to be specified, Qd and RL, with the possibility of importing the results into a database.The test is performed in fixed diffused light.The sample should be illuminated with a D65 standard light source of constant luminance.The measurement is carried out when the ambient temperature is between 0 and 30 °C and the temperature of the test sample/surface is between 5 and 40 °C.The Portable LTL-X Mark II device does not allow for the use of an observation angle of 1°, which prevents the observation of a section longer than 30 m.Therefore, the value of the scattered light luminance coefficient Qd is an approximation of the luminance coefficient Qo.

Validation of the Method
Every research method is subject to measurement error.The source of error may be an operator, the measurement method itself, or inaccuracies resulting from the calibration of the sensors on the measuring device.The effectiveness of the measurement method was assessed to make sure that it is reliable and representative.The method (Section 2.4) involved preparing an original test stand including the preparation of samples.Provisions of ISO 5725-2 [44] were the basis for determining the accuracy and precision of the method.The stability of the measurement process was evaluated using the procedures of the R&R per AIAG [45] based on the analysis of variance (repeatability and reproducibility).To validate the measurement method effectively, the experiment needed careful planning.This involved breaking down the process into specific steps and identifying any factors that might cause variability in the Qd and RL measurements.Hence, the validation process had the following:  Two operators;  Two reflectometers;  Four randomly selected aggregate samples (light and dark).
The results of the method validation are shown in Figure 5.The test stand was set up to determine the luminance coefficient of aggregates and mineral mixtures.According to the Polish regulations contained in WT-2 [43] and PN-EN 1436 [39], the measurement of the luminance ratio should be carried out at an angle of 2.29 • (equivalent to observing the road from a distance of 30 m from the position of a passenger car driver).The measurement field should be a rectangle measuring 185 mm × 50 mm, with an angular spread of ±0.17 • .This requirement was met by the LTL-X Mark II device used to perform this study.The device allows two parameters to be specified, Qd and RL, with the possibility of importing the results into a database.The test is performed in fixed diffused light.The sample should be illuminated with a D65 standard light source of constant luminance.The measurement is carried out when the ambient temperature is between 0 and 30 • C and the temperature of the test sample/surface is between 5 and 40 • C. The Portable LTL-X Mark II device does not allow for the use of an observation angle of 1 • , which prevents the observation of a section longer than 30 m.Therefore, the value of the scattered light luminance coefficient Qd is an approximation of the luminance coefficient Qo.

Validation of the Method
Every research method is subject to measurement error.The source of error may be an operator, the measurement method itself, or inaccuracies resulting from the calibration of the sensors on the measuring device.The effectiveness of the measurement method was assessed to make sure that it is reliable and representative.The method (Section 2.4) involved preparing an original test stand including the preparation of samples.Provisions of ISO 5725-2 [44] were the basis for determining the accuracy and precision of the method.The stability of the measurement process was evaluated using the procedures of the R&R per AIAG [45] based on the analysis of variance (repeatability and reproducibility).To validate the measurement method effectively, the experiment needed careful planning.This involved breaking down the process into specific steps and identifying any factors that might cause variability in the Qd and RL measurements.Hence, the validation process had the following: • Two operators; • Two reflectometers; • Four randomly selected aggregate samples (light and dark).
The results of the method validation are shown in Figure 5. Two hundred measurements were used in this study.Figure 5 shows the operator codes.Operator P represents measurements conducted at the Kielce University of Technology.Operator D was assigned to another research centre participating in the comparative study.The measurements were performed using a basic group of the following four aggregates: melaphyre 2/5, quartzite 5/8, basalt 8/11, and dolomite 2/8, repeating each measurement four times.As shown in Figure 5, the reproducibility is high, and the repeatability of the results is very similar.However, to definitively determine the process stability, a table summarising the characteristics of the research process is presented below (Table 3).Two hundred measurements were used in this study.Figure 5 shows codes.Operator P represents measurements conducted at the Kielce U Technology.Operator D was assigned to another research centre particip comparative study.The measurements were performed using a basic g following four aggregates: melaphyre 2/5, quartzite 5/8, basalt 8/11, and d repeating each measurement four times.As shown in Figure 5, the reproduci and the repeatability of the results is very similar.However, to definitively d process stability, a table summarising the characteristics of the researc presented below (Table 3).Repeatability, reproducibility, and the contribution of R&R variability to overall process variability (stability) are crucial characteristics of the measurement method.Table 3 reveals excellent repeatability for both Qd (6.4

RL Value
These values are quite low, considering the significant variation in aggregate petrography and grain size.The key metric is total R&R, reflecting overall measurement method stability.Qd and RL achieved total R&R values of 8.26% and 4.77%, respectively.According to AIAG procedures, a measurement process with a total R&R below 10% is considered stable.This signifies that the proposed method and its results are representative and highly reproducible by other trained operators using calibrated equipment.Low variability demonstrates the reliability of the measurement method and the resulting data.This stability is a crucial step for building reliable machine learning models.With this confirmation for individual aggregates, this study progressed to analysing mineral mixtures.

Mineral Mix Grading Curves
The structure of the input mineral mixture set was based on the use of the designed compositions of 30 mineral mixtures intended for actual road surfaces subjected to category KR5-7 (7.3•10 6 ÷ 52•10 6 ESAL) traffic loads.The compositions were determined using the limit curves method for asphalt concrete mixtures intended for the wearing course.The aggregate grading curves are summarised below (Figure 6).
The selected mixtures included SMA and AC.The maximum grain size D imposed by WT-2/2014 [43] is 11.2 mm for wearing course mixtures.The top sieve sizes used in the analysis were 8 and 11.2 mm, respectively.The mineral mixture skeleton reflected the maximum variation in aggregate colour.It was important to prepare the mineral mixtures exclusively from the aggregate base given in Table 1.
Appl.Sci.2024, 14, x FOR PEER REVIEW confirmation for individual aggregates, this study progressed to analysin mixtures.

Mineral Mix Grading Curves
The structure of the input mineral mixture set was based on the use of th compositions of 30 mineral mixtures intended for actual road surfaces su category KR5-7 (7.3•10 6 ÷ 52•10 6 ESAL) traffic loads.The compositions were d using the limit curves method for asphalt concrete mixtures intended for th course.The aggregate grading curves are summarised below (Figure 6).The selected mixtures included SMA and AC.The maximum grain size D by WT-2/2014 [43] is 11.2 mm for wearing course mixtures.The top sieve sizes analysis were 8 and 11.2 mm, respectively.The mineral mixture skeleton re maximum variation in aggregate colour.It was important to prepare the minera exclusively from the aggregate base given in Table 1.

Polarising Microscope Examination
The petrographic examination was performed using a polarising micro sampling process was performed using the quartz method in accordance with [46].Microscopic observations were made using eight prepared aggregate/roc thin plates, i.e., uncovered polished (universal) thin plates, which allow observa both polarised transmitted and reflected light.
This study aimed to describe the petrography of the aggregate/rock sampl of mineral composition, rock structure, and texture, determine the types describe the matrix, and determine the type of opaque minerals (observati reflected light).Observations of aggregate/rock preparations were carried o Olympus BX-51 polarising microscope using polarised transmitted light.Ph documentation was made using an Olympus SC18 camera.

Polarising Microscope Examination
The petrographic examination was performed using a polarising microscope.The sampling process was performed using the quartz method in accordance with EN 932-1 [46].Microscopic observations were made using eight prepared aggregate/rock slides on thin plates, i.e., uncovered polished (universal) thin plates, which allow observation under both polarised transmitted and reflected light.
This study aimed to describe the petrography of the aggregate/rock samples in terms of mineral composition, rock structure, and texture, determine the types of cement, describe the matrix, and determine the type of opaque minerals (observations under reflected light).Observations of aggregate/rock preparations were carried out with an Olympus BX-51 polarising microscope using polarised transmitted light.Photographic documentation was made using an Olympus SC18 camera.

Luminance Coefficient Qd of the Aggregate vs. Mineralogical Composition
The detailed process of applying the boosted random tree (BT) algorithm required to predict the luminance ratio Qd is explained in detail in the article [15].The results that fell within its scope provide the foundation for the search for further links that are the subject of this article.A summary of the test results, regarding the change in Qd in relation to aggregate type, is shown in Figure 7.
The unpublished Figure 7 shown represents the quality of the model fit by aggregate type.Taking into account the level of fractions used in Table 1, the quality of the represen-tation of reality by the gradient-enhanced tree (BT) model was R 2 = 0.96 with relative error MAE = 4.3 mcd•m −2 •lx −1 .Observing the results in Figure 7, it can be seen that the greatest dispersion of results was observed against the granite aggregate.With the results of the resulting BT model [15], a projection was made to illustrate the probability density of the predicted feature (Predicted Qd) by rock type.A graphical representation of the projection is shown in a ridge diagram developed in R (Figure 8).The unpublished Figure 7 shown represents the quality of the model fit by aggrega type.Taking into account the level of fractions used in Table 1, the quality of th representation of reality by the gradient-enhanced tree (BT) model was R 2 = 0.96 wi relative error MAE = 4.3 mcd⋅m −2 ⋅lx −1 .Observing the results in Figure 7, it can be seen th the greatest dispersion of results was observed against the granite aggregate.With th results of the resulting BT model [15], a projection was made to illustrate the probabili density of the predicted feature (Predicted Qd) by rock type.A graphical representatio of the projection is shown in a ridge diagram developed in R (Figure 8).Considering the value of the luminance coefficient, classifying the road pavement a black, Qd < 52 mcd⋅m −2 ⋅lx −1 , it must be concluded that basalt aggregate and melaphy aggregate do not significantly affect the brightening of the pavement.In the case of gabbr rock aggregate, it does not allow for pavement brightening in certain cases.A much mo  The unpublished Figure 7 shown represents the quality of the model fit by ag type.Taking into account the level of fractions used in Table 1, the quality representation of reality by the gradient-enhanced tree (BT) model was R 2 = 0.9 relative error MAE = 4.3 mcd⋅m −2 ⋅lx −1 .Observing the results in Figure 7, it can be se the greatest dispersion of results was observed against the granite aggregate.W results of the resulting BT model [15], a projection was made to illustrate the pro density of the predicted feature (Predicted Qd) by rock type.A graphical represe of the projection is shown in a ridge diagram developed in R (Figure 8).Considering the value of the luminance coefficient, classifying the road pavem black, Qd < 52 mcd⋅m −2 ⋅lx −1 , it must be concluded that basalt aggregate and me aggregate do not significantly affect the brightening of the pavement.In the case of rock aggregate, it does not allow for pavement brightening in certain cases.A muc favourable result in terms of magmatic rocks can be obtained by using aggrega amphibolite and granite rocks.According to WT-2/2014, for surface illum aggregate with a Qd > 70 mcd⋅m −2 ⋅lx −1 , should be used, i.e., in the examined set, al luminance coefficient close to the median value (Figure 8).In this group, the best were obtained using quartzite sandstone (sedimentary) aggregate and lim (sedimentary).In this group, very good results can be achieved using granite ag (igneous).However, it should be noted that all the rocks mentioned are formed diff Considering the value of the luminance coefficient, classifying the road pavement as black, Qd < 52 mcd•m −2 •lx −1 , it must be concluded that basalt aggregate and melaphyre aggregate do not significantly affect the brightening of the pavement.In the case of gabbro rock aggregate, it does not allow for pavement brightening in certain cases.A much more favourable result in terms of magmatic rocks can be obtained by using aggregate from amphibolite and granite rocks.According to WT-2/2014, for surface illumination, aggregate with a Qd > 70 mcd•m −2 •lx −1 , should be used, i.e., in the examined set, all with a luminance coefficient close to the median value (Figure 8).In this group, the best results were obtained using quartzite sandstone (sedimentary) aggregate and limestone (sedimentary).In this group, very good results can be achieved using granite aggregate (igneous).However, it should be noted that all the rocks mentioned are formed differently and have different mineralogical structures.Therefore, it is to be expected that certain groups of minerals will be responsible for the luminosity factor Qd results obtained.However, before a mineralogical analysis is carried out, it is worth projecting the RL feature, i.e., the level of glare that the rocks generate from artificial light (car headlights).A graphical representation of the probability distribution of the measured RL feature is shown in Figure 9.
Appl.Sci.2024, 14, x FOR PEER REVIEW and have different mineralogical structures.Therefore, it is to be expected that groups of minerals will be responsible for the luminosity factor Qd results ob However, before a mineralogical analysis is carried out, it is worth projecting feature, i.e., the level of glare that the rocks generate from artificial light (car head A graphical representation of the probability distribution of the measured RL fe shown in Figure 9. Figure 9 indicates the average observed level of road surface reflectivity RL within the range of 10 ÷ 30 mcd⋅m −2 ⋅lx −1 .Basalt aggregate, similar to the Qd, d introduce any additional improvement in the reflectivity of the pavemen amphibolite aggregate also has a reflectivity similar to the road surface, although t of the Qd characteristic was significantly higher than the threshold value at wh pavement is considered 'black'.A significant contribution to reflectivity was obse the results of limestone, granite and quartzite sandstone aggregate.It is nota among the results of the reflectance coefficient in artificial light for quartzite san aggregate, there was a certain group of results in quartzite sandstone aggregate RL value >70 mcd⋅m −2 ⋅lx −1 .The observed singularity and the lack of a strong cor between Qd and RL suggest that the mineralogical composition can definitely con to the understanding of the aggregate luminosity phenomenon.

Regression Model of Aggregate Luminance Coefficient Taking Petrography into Acco
The mineralogical tests carried out mostly correctly identified the t aggregate/rock, although some variation was noted in the following aggregate type: amphibolite.All of them can be linked to the genesis of the deposit contamination effect caused by the aggregate production process.Photograph rocks used for the luminance ratio modelling, along with a view of the grinds, are in Figure 10.Basalt aggregate, similar to the Qd, does not introduce any additional improvement in the reflectivity of the pavement.The amphibolite aggregate also has a reflectivity similar to the road surface, although the level of the Qd characteristic was significantly higher than the threshold value at which the pavement is considered 'black'.A significant contribution to reflectivity was observed in the results of limestone, granite and quartzite sandstone aggregate.It is notable that among the results of the reflectance coefficient in artificial light for quartzite sandstone aggregate, there was a certain group of results in quartzite sandstone aggregate with an RL value >70 mcd•m −2 •lx −1 .The observed singularity and the lack of a strong correlation between Qd and RL suggest that the mineralogical composition can definitely contribute to the understanding of the aggregate luminosity phenomenon.

Regression Model of Aggregate Luminance Coefficient Taking Petrography into Account
The mineralogical tests carried out mostly correctly identified the type of aggregate/rock, although some variation was noted in the following aggregate sample type: amphibolite.All of them can be linked to the genesis of the deposit or the contamination effect caused by the aggregate production process.Photographs of the rocks used for the luminance ratio modelling, along with a view of the grinds, are shown in Figure 10.
Appl.Sci.2024, 14, x FOR PEER REVIEW 13 of 28 and have different mineralogical structures.Therefore, it is to be expected that certain groups of minerals will be responsible for the luminosity factor Qd results obtained.However, before a mineralogical analysis is carried out, it is worth projecting the RL feature, i.e., the level of glare that the rocks generate from artificial light (car headlights).
A graphical representation of the probability distribution of the measured RL feature is shown in Figure 9. Figure 9 indicates the average observed level of road surface reflectivity RL falling within the range of 10 ÷ 30 mcd⋅m −2 ⋅lx −1 .Basalt aggregate, similar to the Qd, does not introduce any additional improvement in the reflectivity of the pavement.The amphibolite aggregate also has a reflectivity similar to the road surface, although the level of the Qd characteristic was significantly higher than the threshold value at which the pavement is considered 'black'.A significant contribution to reflectivity was observed in the results of limestone, granite and quartzite sandstone aggregate.It is notable that among the results of the reflectance coefficient in artificial light for quartzite sandstone aggregate, there was a certain group of results in quartzite sandstone aggregate with an RL value >70 mcd⋅m −2 ⋅lx −1 .The observed singularity and the lack of a strong correlation between Qd and RL suggest that the mineralogical composition can definitely contribute to the understanding of the aggregate luminosity phenomenon.

Regression Model of Aggregate Luminance Coefficient Taking Petrography into Account
The mineralogical tests carried out mostly correctly identified the type of aggregate/rock, although some variation was noted in the following aggregate sample type: amphibolite.All of them can be linked to the genesis of the deposit or the contamination effect caused by the aggregate production process.Photographs of the rocks used for the luminance ratio modelling, along with a view of the grinds, are shown in Figure 10.The mineralogical evaluation was based on a petrographic examination of thin plates under a microscope suggesting the study [47].The analysis was performed, excluding detailed geochemical analyses, using XRM microscopy.The state characterising the presence of a certain mineral was expressed by the symbol T, while its absence was expressed by the symbol N. The clustering results were performed using the dplyr and ggplot2 libraries in the R programming language [48,49].A graphical visualisation of the results of the petrographic evaluation performed is shown in Figure 11.Observing the results shown in Figure 11, it should be noted that the brightness of the aggregate does not depend on the presence of only one type of mineral.For sedimentary rocks (limestone), calcite was the dominant mineral, sedimentary rocks (quartzite sandstone) were dominated by quartz, and in igneous rocks, plagioclase and pyroxene were dominant.Observing the preliminary results, it was found that the contribution of quartz or calcite was definitely responsible for the high Qd level.In contrast, by simple elimination, the mineral mica was probably responsible for the high reflectivity state at night (RL).Thereby, its pearly sheen might have affected parameter RL.With the petrographic evaluation and the specified aggregate granulation available, an attempt was made to analyse their influence on the Qd characteristic.The petrographic analysis presented indicates that a single mineral was not attributed to a single rock type from which the aggregate range was produced.In the case of quartz, its occurrence was observed in granite and quartzite sandstone.Calcite, on the other hand, is characteristic of sedimentary rock (limestone).Therefore, there is a high probability that the formulation of the regression model based on the boosted tree (BT) technique will produce additional rules that describe the luminance phenomenon in the aggregate even more accurately and the resulting luminance coefficient value will have minimal estimation error.The mineralogical evaluation was based on a petrographic examination of thin plates under a microscope suggesting the study [47].The analysis was performed, excluding detailed geochemical analyses, using XRM microscopy.The state characterising the presence of a certain mineral was expressed by the symbol T, while its absence was expressed by the symbol N. The clustering results were performed using the dplyr and ggplot2 libraries in the R programming language [48,49].A graphical visualisation of the results of the petrographic evaluation performed is shown in Figure 11.The mineralogical evaluation was based on a petrographic examination of thin plates under a microscope suggesting the study [47].The analysis was performed, excluding detailed geochemical analyses, using XRM microscopy.The state characterising the presence of a certain mineral was expressed by the symbol T, while its absence was expressed by the symbol N. The clustering results were performed using the dplyr and ggplot2 libraries in the R programming language [48,49].A graphical visualisation of the results of the petrographic evaluation performed is shown in Figure 11.Observing the results shown in Figure 11, it should be noted that the brightness of the aggregate does not depend on the presence of only one type of mineral.For sedimentary rocks (limestone), calcite was the dominant mineral, sedimentary rocks (quartzite sandstone) were dominated by quartz, and in igneous rocks, plagioclase and pyroxene were dominant.Observing the preliminary results, it was found that the contribution of quartz or calcite was definitely responsible for the high Qd level.In contrast, by simple elimination, the mineral mica was probably responsible for the high reflectivity state at night (RL).Thereby, its pearly sheen might have affected parameter RL.With the petrographic evaluation and the specified aggregate granulation available, an attempt was made to analyse their influence on the Qd characteristic.The petrographic analysis presented indicates that a single mineral was not attributed to a single rock type from which the aggregate range was produced.In the case of quartz, its occurrence was observed in granite and quartzite sandstone.Calcite, on the other hand, is characteristic of sedimentary rock (limestone).Therefore, there is a high probability that the formulation of the regression model based on the boosted tree (BT) technique will produce additional rules that describe the luminance phenomenon in the aggregate even more accurately and the resulting luminance coefficient value will have minimal estimation error.Observing the results shown in Figure 11, it should be noted that the brightness of the aggregate does not depend on the presence of only one type of mineral.For sedimentary rocks (limestone), calcite was the dominant mineral, sedimentary rocks (quartzite sandstone) were dominated by quartz, and in igneous rocks, plagioclase and pyroxene were dominant.Observing the preliminary results, it was found that the contribution of quartz or calcite was definitely responsible for the high Qd level.In contrast, by simple elimination, the mineral mica was probably responsible for the high reflectivity state at night (RL).Thereby, its pearly sheen might have affected parameter RL.With the petrographic evaluation and the specified aggregate granulation available, an attempt was made to analyse their influence on the Qd characteristic.The petrographic analysis presented indicates that a single mineral was not attributed to a single rock type from which the aggregate range was produced.In the case of quartz, its occurrence was observed in granite and quartzite sandstone.Calcite, on the other hand, is characteristic of sedimentary rock (limestone).Therefore, there is a high probability that the formulation of the regression model based on the boosted tree (BT) technique will produce additional rules that describe the luminance phenomenon in the aggregate even more accurately and the resulting luminance coefficient value will have minimal estimation error.
The input file used to build the model was based on the data collected during the petrographic analysis and the data given in Table 1.The BT technique was chosen for the analysis in order to be able to refer to the results in the paper [15].The optimal learning parameters were determined after taking the tuning process into account.The number of trees was limited to 400.During the construction of the BT model, a learning ratio η of 0.1 was used [50], while the ratio for randomising the learning samples in successive amplification steps was 0.5, suggesting the recommendations in the paper [51].The final BT model was characterised by a tree structure with a maximum depth of 10 levels.It was very important to avoid 'over-learning' when learning the model, so the regularisation parameters α = 1, λ = 0 [52] were subjected to a fine-tuning process.The final model was built with a tree count of 174.The analyses obtained were performed using Statistica [51].The learning flow and parameter validity, using the RMSE metric, are shown in Figure 12.
Appl.Sci.2024, 14, x FOR PEER REVIEW 16 of 28 The input file used to build the model was based on the data collected during the petrographic analysis and the data given in Table 1.The BT technique was chosen for the analysis in order to be able to refer to the results in the paper [15].The optimal learning parameters were determined after taking the tuning process into account.The number of trees was limited to 400.During the construction of the BT model, a learning ratio η of 0.1 was used [50], while the ratio for randomising the learning samples in successive amplification steps was 0.5, suggesting the recommendations in the paper [51].The final BT model was characterised by a tree structure with a maximum depth of 10 levels.It was very important to avoid 'over-learning' when learning the model, so the regularisation parameters α =1, λ = 0 [52]were subjected to a fine-tuning process.The final model was built with a tree count of 174.The analyses obtained were performed using Statistica [51].The learning flow and parameter validity, using the RMSE metric, are shown in Figure 12.Note the results of the importance indicators.The predictor validity graph (Figure 12b) suggests that the feature related to the reflective properties of the aggregate illuminated by car headlights had the greatest influence on the formulated set of rules for the learning process.In addition, the aggregate grain size had a very important influence on the discriminatory rules obtained.There is a logical rationale for this, as a higher proportion of fine aggregate results in an increase in its volumetric proportion in the composition of the mineral mixture and an increase in its specific surface area.With regard to the mineralogical composition, the percentage of minerals such as pyroxene, plagioclase, and olivine mainly determined the distribution of the aggregate luminance value (Qd).Of the mineral assemblage, calcite (limestone and quartzite) and potassium feldspars (granite) played an important role in shaping the high clarity of the aggregate.It can be added that these minerals are mainly colourless, white minerals with a glassy shine.The analysis carried out was complemented by a variability graph developed based on the predicted results of the Qd trait using the BT model.The diagram below is shown in Figure 13.Note the results of the importance indicators.The predictor validity graph (Figure 12b) suggests that the feature related to the reflective properties of the aggregate illuminated by car headlights had the greatest influence on the formulated set of rules for the learning process.In addition, the aggregate grain size had a very important influence on the discriminatory rules obtained.There is a logical rationale for this, as a higher proportion of fine aggregate results in an increase in its volumetric proportion in the composition of the mineral mixture and an increase in its specific surface area.With regard to the mineralogical composition, the percentage of minerals such as pyroxene, plagioclase, and olivine mainly determined the distribution of the aggregate luminance value (Qd).Of the mineral assemblage, calcite (limestone and quartzite) and potassium feldspars (granite) played an important role in shaping the high clarity of the aggregate.It can be added that these minerals are mainly colourless, white minerals with a glassy shine.The analysis carried out was complemented by a variability graph developed based on the predicted results of the Qd trait using the BT model.The diagram below is shown in Figure 13.Observing the results in Figure 13, it should be noted that the presence of a pyr type mineral strongly divides the whole community into dark-and light-coloured gates according to the classification of the report [52].According to its results, an gate with a luminance ratio of Qd < 70 mcd⋅m −2 ⋅lx −1 is an aggregate that is considere It should be noted that pyroxene is a major component of deep-sea magmatic rock basalt.A very high Qd value was obtained for rocks containing calcite, which is th component of a sedimentary rock such as limestone.The same picture is given b characterised by the presence of plagioclase and quartz, i.e., granitic rock.A very in ing observation is the interaction of quartz and mica, the minerals found in some of quartzite sandstone aggregate.The interaction of these two minerals allowed for a ing Qd > 100 mcd⋅m −2 ⋅lx −1 , which means aggregates with high lightening values potential road surface.The presence of the mineral mica (lat.'shine') has alread signalled as improving the reflectivity of the aggregate in artificial light.In order t pare the effectiveness of the modelling including petrographic analysis, the results model including mineralogical composition were compared with the results provi the model included in the work [15].The following three metrics were used for marking:  Root mean square error (RMSE);  R-squared (R 2 );  Mean absolute error (MAE).

Appl
The results of the comparison are shown in Table 4.  Observing the results in Figure 13, it should be noted that the presence of a pyroxenetype mineral strongly divides the whole community into dark-and light-coloured aggregates according to the classification of the report [52].According to its results, an aggregate with a luminance ratio of Qd < 70 mcd•m −2 •lx −1 is an aggregate that is considered dark.It should be noted that pyroxene is a major component of deep-sea magmatic rocks, e.g., basalt.A very high Qd value was obtained for rocks containing calcite, which is the main component of a sedimentary rock such as limestone.The same picture is given by rules characterised by the presence of plagioclase and quartz, i.e., granitic rock.A very interesting observation is the interaction of quartz and mica, the minerals found in some grains of quartzite sandstone aggregate.The interaction of these two minerals allowed for achieving Qd > 100 mcd•m −2 •lx −1 , which means aggregates with high lightening values for the potential road surface.The presence of the mineral mica (lat.'shine') has already been signalled as improving the reflectivity of the aggregate in artificial light.In order to compare the effectiveness of the modelling including petrographic analysis, the results of the model including mineralogical composition were compared with the results provided by the model included in the work [15].The following three metrics were used for benchmarking: The results of the comparison are shown in Table 4.
Observing the results in Table 4, it should be noted that the degree of improvement in the prediction of the Qd trait value compared to the results in the [15] paper increased slightly (MAE decrease of only 0.2 mcd•m −2 •lx −1 ).The consideration of the mineralogical composition was of greater importance in the cognitive context of the aggregate luminance phenomenon.In the regression approach analysed, expressing the petrographic characteristics using only the name of the rock from which the aggregate was produced can be considered sufficient from the point of view of the predictive quality of the model.It is likely that extending the research programme to include rock chemistry would have a far greater impact on the accuracy of aggregate luminance ratio prediction.The modelling of the luminance coefficient value Qd of the mineral mixture was based on the conclusions and results of the luminance coefficient modelling for the aggregate.The model developed in Section 3.2 was selected for further analysis as it allowed for a reduction in the forecast error attributed to the aggregate.However, it should be borne in mind that the inclusion of a model incorporating the results of the mineralogical analysis will increase the quality of the luminosity ratio prediction but will definitely reduce its usefulness from the point of view of practical applications.This is due to the fact that mineralogical analyses are rarely performed in the road industry for a given aggregate.Independently of this, the experience and results of the model given in the paper [15] can also be used for the analysis in the absence of detailed petrographic investigations.
As mentioned before, the structure of the mineral mix input set was based on the use of designed compositions of 30 mineral mixes for real road pavements loaded with medium traffic of category KR5-7 (7.3•10 6 ÷ 52•10 6 ESAL).All the mineral mixtures were designed for the pavement-wearing course made of asphalt concrete and stone mastic asphalt.All mineral mixtures had to comply with the grain size requirements applicable in Poland, according to WT-2/2014 [43].The introduction of such conditions ruled out the possibility of using a single type of aggregate, as its crumb pile would have prevented the compaction of a mineral and asphalt mixture (mma) made with it under real-world conditions.Another limitation was due to the acidity of the rocks, i.e., the silica content (SiO 2 ).The use of acid rock, e.g., quartzite sandstone and granite, would result in a loss of the required water resistance of the mma due to the low adhesion of these rocks to the asphalt.On the other hand, the use of an aggregate with a high adhesion with limestone will not provide the required value of resistance to fragmentation (Los Angeles coefficient) LA < 40.Taking all conditions into account, the mineral mixture consisted of three to four aggregates of different granulation types (Kx).The advantage of doing it this way was that it was possible to replicate the actual mineral and asphalt mixtures that were used to produce the mma and thus the rules that were specified in the model applied to real conditions.The knowledge-containing model developed in the previous chapter for predicting the luminance coefficient of the aggregate (Qx) was implemented in the modelling of the luminance coefficient of the mineral mixer in the form of an XML exchange file.The number of results in the input set was 450 and its structure is shown in Table 5.
Table 5. Structure of the input set for the determination of Qd of the mineral mixture.

Quantitative Dependent Variable
Luminance ratio in diffuse light (Qd) Quantitative independent variable (quantitative predictor) The luminance coefficient Qd for the aggregate (value derived from model described in Section 3.2), Qx Percentage fraction of aggregate, Px % When building the model, the finest fraction of the U1 aggregate with a grain size of 0/2 was not included.This type of fraction would definitely falsify the luminance ratio result.In addition, the fine aggregate fractions are surrounded by the asphalt to form a mastic (fine aggregate and asphalt binder); therefore, it would be unreasonable to leave this fraction in mm.Nevertheless, they are taken into account during the design of the mm composition.An algorithm for proceeding to model the luminance ratio of the mineral mixture in the form of a flowchart is shown in Figure 14.When building the model, the finest fraction of the U1 aggregate with a grain size of 0/2 was not included.This type of fraction would definitely falsify the luminance ratio result.In addition, the fine aggregate fractions are surrounded by the asphalt to form a mastic (fine aggregate and asphalt binder); therefore, it would be unreasonable to leave this fraction in mm.Nevertheless, they are taken into account during the design of the mm composition.An algorithm for proceeding to model the luminance ratio of the mineral mixture in the form of a flowchart is shown in Figure 14.The best machine learning model had to exhibit the smallest RMSE value among their models.In the case of the MARS model, it was required to give quality labels to some of the variables, and this technique ultimately proved unsuccessful.The C&RT technique also failed to produce a satisfactory prediction result.A summary of the preliminary results is shown in Table 6.The task at hand was new, so to select an appropriate DM technique, the tool provided by the Statistica package included in the Data Miner Recipes module was used.Its operation and outcome should be seen primarily as a feasibility study as to the integrity of the dataset, as well as an indication of the technique that is likely to be most effective for luminance ratio prediction.The following four DM regression techniques were initially selected for the task: The best machine learning model had to exhibit the smallest RMSE value among their models.In the case of the MARS model, it was required to give quality labels to some of the variables, and this technique ultimately proved unsuccessful.The C&RT technique also failed to produce a satisfactory prediction result.A summary of the preliminary results is shown in Table 6.Of all the learning techniques, the reinforced tree (BT) algorithm was selected for further evaluation.The results of the quality of fit obtained took into account the use of all the results in the set without dividing them into a teaching and test set.The modelling function has undergone a fine-tuning process.This process was performed using the caret library available in the R programming language, which allows any modelling function to be effectively tuned.The following parameters were taken into account in the finetuning process: The tuning process consisted of iterating specific combinations of BT model parameters (xgbTree method) considered in a fixed parameter grid using also a cross-check.Crossvalidation was introduced to avoid excessive overfitting of the model built from the training set.Then, after a time-consuming calculation process, the result was presented in the form of a vector of parameter values at which the model achieved the highest efficiency.The RMSE metric was used as a criterion for selecting the best model.A graph representing an extract of the RMSE results from the parameter tuning process is shown in Figure 15.Of all the learning techniques, the reinforced tree (BT) algorithm was se further evaluation.The results of the quality of fit obtained took into account the the results in the set without dividing them into a teaching and test set.The m function has undergone a fine-tuning process.This process was performed usin library available in the R programming language, which allows any modelling to be effectively tuned.The following parameters were taken into account in the ing process:  nrounds-controls the maximum number of iterations;  η-controls the learning rate;  -controls regularisation (or prevents overfitting);  max depth-controls the depth of the tree;  min.child weight-refers to the minimum number of instances required node;  subsample-controls the number of samples (observations) supplied to a t

Name
The tuning process consisted of iterating specific combinations of BT mode ters (xgbTree method) considered in a fixed parameter grid using also a cro Cross-validation was introduced to avoid excessive overfitting of the model buil training set.Then, after a time-consuming calculation process, the result was pre the form of a vector of parameter values at which the model achieved the hig ciency.The RMSE metric was used as a criterion for selecting the best model representing an extract of the RMSE results from the parameter tuning process in Figure 15.Finally, the best model, with the lowest RMSE value, after the tuning process was carried out, was characterised by the parameters that are given in Table 7.It should be noted that the test set was used to verify the value of nrounds, the value of which was finally set as 120.Further increases in the nrounds parameter led to overfitting of the BT model.The quality of the model fit containing the results of the entire set (learning and test set) between the feature Qd obs (observed values) and the set of predicted values Qd predic was R 2 = 0.87, MAE = 4.4 mcd•m −2 •lx −1 and RMSE = 5.7 mcd•m −2 •lx −1 .The quality results obtained were considered satisfactory.It was also important to assess the quality of the model by analysing its structure by means of a validity chart of the variables.On the basis of these, it is possible to assess which variable has the greatest influence on the distribution of trees and the relationship between them and allows practical conclusions to be drawn.Variable importance plot and quality of fit model Qd predic vs. Qd obs are shown in Figure 16.Finally, the best model, with the lowest RMSE value, after the tuning process was carried out, was characterised by the parameters that are given in Table 7.It should be noted that the test set was used to verify the value of nrounds, the value of which was finally set as 120.Further increases in the nrounds parameter led to overfitting of the BT model.The quality of the model fit containing the results of the entire set (learning and test set) between the feature Qdobs (observed values) and the set of predicted values Qdpredic was R 2 = 0.87, MAE = 4.4 mcd⋅m −2 ⋅lx −1 and RMSE = 5.7 mcd⋅m −2 ⋅lx −1 .The quality results obtained were considered satisfactory.It was also important to assess the quality of the model by analysing its structure by means of a validity chart of the variables.On the basis of these, it is possible to assess which variable has the greatest influence on the distribution of trees and the relationship between them and allows practical conclusions to be drawn.Variable importance plot and quality of fit model Qdpredic vs. Qdobs are shown in Figure 16.Observing the results in Figure 16b, it should be noted that the luminosity coefficient of aggregate fraction (component) No. 2 and No. 3 (Q2, Q3) had the greatest influence on the determination of rules when building the BT model.The percentages of fractions two (P2) and three (P3) were also very significant.An interesting note comes from the assessment of the importance of the following feature interactions: K3-Basalt and K3-Quartize.This was most likely due to the presence of pyroxene in the aggregate, which clearly separates the community into light and dark aggregates (as per Figure 8).Thus, the presence of these rocks in fraction 3 will significantly affect the final luminance value of the mineral mixture.The granularity of the grain size (Ux) was also important, although no longer as important as the characteristics mentioned.In order to understand the structure of the set, partial dependence plots were used, the purpose of which was to determine the strength of the influence of a given variable while marginalising the influence of the others and expressing it in terms of an average value of the Qd characteristic (denoted as yhat).It is a useful analytical tool, especially when we are interested in the logical justification of the presence of variables, and when we are looking for general conclusions of a practical nature.The information in Figure 16 is developed and graphically presented in Figure 17 by type of component in the mineral mix (excluding component 1).Observing the results in Figure 16b, it should be noted that the luminosity coefficient of aggregate fraction (component) No. 2 and No. 3 (Q2, Q3) had the greatest influence on the determination of rules when building the BT model.The percentages of fractions two (P2) and three (P3) were also very significant.An interesting note comes from the assessment of the importance of the following feature interactions: K3-Basalt and K3-Quartize.This was most likely due to the presence of pyroxene in the aggregate, which clearly separates the community into light and dark aggregates (as per Figure 8).Thus, the presence of these rocks in fraction 3 will significantly affect the final luminance value of the mineral mixture.The granularity of the grain size (Ux) was also important, although no longer as important as the characteristics mentioned.In order to understand the structure of the set, partial dependence plots were used, the purpose of which was to determine the strength of the influence of a given variable while marginalising the influence of the others and expressing it in terms of an average value of the Qd characteristic (denoted as yhat).It is a useful analytical tool, especially when we are interested in the logical justification of the presence of variables, and when we are looking for general conclusions of a practical nature.The information in Figure 16 is developed and graphically presented in Figure 17   Due to the small effect of aggregate granulation on the Qd value (Figure 16b), a subgraph (Ux) was not made for this variable.In contrast, the influence of the characteristics Kx, Qx, and Px was much more significant.Before carrying out the analysis, it is useful to indicate what granularity each mineral mixture component had.Aggregate No. 2 (appropriately described by features K2, Q2, P2) could occur as a fraction, 2/5 or 2/8, aggregate No. 3 could occur as a fraction, 2/8, 5/8, while No. 4 could occur as a fraction 8/11 or no fraction.An analysis of Figure 17a indicates the greatest influence on the high brightness of the granite aggregate in fraction No. 2 (K2).In addition, the introduction of quartzite sandstone aggregate as a component of K2 and K3 had a very favourable effect on the luminance coefficient of the mineral mixture (mm).The opposite was the basalt aggregate, the presence of which had the opposite effect.It was much more interesting to find out at what average percentage of luminous aggregate the effect of an increased mm luminance value could be obtained, depending on the component type.Figure 17b,c show that the proportion of Q2 aggregate with a fraction of 2/5 or 2/8 above 40% and with a luminance coefficient Qd > 70 mcd•m −2 •lx −1 caused a sudden increase in the Qd mm characteristic (increase in yhat value).Similarly, in the case of ingredient No. 4 (fraction 8/11), an increase in its share >60% (P4) in the mm composition containing bright aggregate caused a significant increase in the brightness of mm.In component No. 3 (fractions: 2/8 or 5/8), the greatest impact on the luminance coefficient mm was caused by a percentage share from 25% to 50%, and only then when the aggregate from Qd > 80 mcd•m −2 •lx −1 was used.Only quartzite sandstone or granite aggregate could provide such a result.Ingredient No. 4, i.e., aggregate with a fraction of 8/11, only mattered when its share was >60%.This result is justified when its specific surface area is taken into account.Aggregate of this grain size will definitely have a lower specific surface area than the finer fractions found in components 2 and 3. Consequently, the coarsest fraction (No. 4) will have far less impact on the luminance ratio than the fine fraction.However, it should be remembered that the coarse fractions are responsible for the high resistance of the mineral-asphalt mixture (mma) to permanent deformation.Therefore, optimising the composition of the mma for the sake of maintaining high resistance to permanent deformation is likely to reduce the potential of the light aggregate to lighten the pavement.The luminance ratio can also be determined from other assessments.The value of QD can also be determined by using the weighted mean according to Formula (4), as follows: P Q ⋯ P Q Due to the small effect of aggregate granulation on the Qd value (Figure 16b), a subgraph (Ux) was not made for this variable.In contrast, the influence of the characteristics Kx, Qx, and Px was much more significant.Before carrying out the analysis, it is useful to indicate what granularity each mineral mixture component had.Aggregate No. 2 (appropriately described by features K2, Q2, P2) could occur as a fraction, 2/5 or 2/8, aggregate No. 3 could occur as a fraction, 2/8, 5/8, while No. 4 could occur as a fraction 8/11 or no fraction.An analysis of Figure 17a indicates the greatest influence on the high brightness of the granite aggregate in fraction No. 2 (K2).In addition, the introduction of quartzite sandstone aggregate as a component of K2 and K3 had a very favourable effect on the luminance coefficient of the mineral mixture (mm).The opposite was the basalt aggregate, the presence of which had the opposite effect.It was much more interesting to find out at what average percentage of luminous aggregate the effect of an increased mm luminance value could be obtained, depending on the component type.Figure 17b,c show that the proportion of Q2 aggregate with a fraction of 2/5 or 2/8 above 40% and with a luminance coefficient Qd > 70 mcd•m −2 •lx −1 caused a sudden increase in the Qd mm characteristic (increase in yhat value).Similarly, in the case of ingredient No. 4 (fraction 8/11), an increase in its share >60% (P4) in the mm composition containing bright aggregate caused a significant increase in the brightness of mm.In component No. 3 (fractions: 2/8 or 5/8), the greatest impact on the luminance coefficient mm was caused by a percentage share from 25% to 50%, and only then when the aggregate from Qd > 80 mcd•m −2 •lx −1 was used.Only quartzite sandstone or granite aggregate could provide such a result.Ingredient No. 4, i.e., aggregate with a fraction of 8/11, only mattered when its share was >60%.This result is justified when its specific surface area is taken into account.Aggregate of this grain size will definitely have a lower specific surface area than the finer fractions found in components 2 and 3. Consequently, the coarsest fraction (No. 4) will have far less impact on the luminance ratio than the fine fraction.However, it should be remembered that the coarse fractions are responsible for the high resistance of the mineral-asphalt mixture (mma) to permanent deformation.Therefore, optimising the composition of the mma for the sake of maintaining high resistance to permanent deformation is likely to reduce the potential of the light aggregate to lighten the pavement.The luminance ratio can also be determined from other assessments.The value of QD can also be determined by using the weighted mean according to Formula (4), as follows: Qd mean,weighted = where Qd mean,weighted is the weighted mean of luminance coefficient mm and P i is the percentage of aggregate in the i-th component mm, luminance coefficient of an aggregate of the i-th component.The results of the projected Qd mean.weightedvalue are presented graphically in the summary of results shown in Figure 18.
pl. Sci.2024, 14, x FOR PEER REVIEW where Qdmean,weighted is the weighted mean of luminance coefficient mm a centage of aggregate in the i-th component mm, luminance coefficient o the i-th component.The results of the projected Qdmean.weightedvalue are p ically in the summary of results shown in Figure 18.The quality of the model fit based on the Qdmean.weightedcalculation d = 0.87 (based on the BT model) to 0.71.This decrease can be explained by the weighted average value of 12%.However, by observing deviations proportionality, the model using a weighted average is unable to explain liers that arose during the analysis.This is because the distribution of th Qd did not have a normal distribution and is characterised by multimo Thus, the central measures used in the parametric tests will not allow prediction of the results of such a complex quantity as the luminance mineral mixture, and the resulting residuals will not meet the homosceda It should be made clear at this point that the interpretation of the from the BT model relates only to the set of aggregates used for the analy tionships occurring between the components also resulted from the regu by the technical requirements WT-1/2014 for aggregates and WT-2/2014 tion of mineral mixtures in force in Poland.However, there is nothing model from being further evaluated using other mineral compositions su compositional rules.The resulting set of results covers a wide spectrum coefficient Qd, as well as the labelled RL coefficient.In summary, the pro tion of the results occurring in the experiment is shown in Figure 19.The quality of the model fit based on the Qd mean.weightedcalculation decreased from R 2 = 0.87 (based on the BT model) to 0.71.This decrease can be explained by the variation in the weighted average value of 12%.However, by observing deviations from the line of proportionality, the model using a weighted average is unable to explain many of the outliers that arose during the analysis.This is because the distribution of the aggregate trait Qd did not have a normal distribution and is characterised by multimodality (Figure 8).Thus, the central measures used in the parametric tests will not allow for an adequate prediction of the results of such a complex quantity as the luminance factor Qd of the mineral mixture, and the resulting residuals will not meet the homoscedasticity condition.
It should be made clear at this point that the interpretation of the results obtained from the BT model relates only to the set of aggregates used for the analysis, and the relationships occurring between the components also resulted from the regulations imposed by the technical requirements WT-1/2014 for aggregates and WT-2/2014 for the composition of mineral mixtures in force in Poland.However, there is nothing to prevent this model from being further evaluated using other mineral compositions subject to different compositional rules.The resulting set of results covers a wide spectrum of the luminance coefficient Qd, as well as the labelled RL coefficient.In summary, the probability distribution of the results occurring in the experiment is shown in Figure 19.The range of luminance ratio results predicted by the Qdpredic model is be mcd⋅m −2 ⋅lx −1 and 116 mcd⋅m −2 ⋅lx −1 .In contrast, the RL factor most often obtained the range 35 ÷ 40 mcd⋅m −2 ⋅lx −1 during the tests.It is the intention of the authors validate and calibrate the developed model predicting the luminance coefficient aggregate, as well as the mineral mixture.In the next step, the relationships bet aggregate, mineral mix, and mineral-asphalt mixture subjected to wear and tea luminance coefficient will be sought.The main objective is to build a DM model the luminance ratio at the design stage of the mineral-asphalt mix.

Conclusions
It should be noted that aggregate resources are not inexhaustible.Theref availability on the market will decrease over time.Currently, mines regulate th of extracted aggregate using the principle of sustainable development.Ther amount of aggregate that is extracted depends on the forecasted demand in the l perspective.Moreover, it should also be taken into account that in the bitumin tures, there are also recycled aggregates, which will also require the assessmen erties and affect the pavement luminance value.Therefore, an effective numeric will definitely facilitate their selection for the composition of mineral mixtures.T elling process presented here proved that a very good representation of the lu coefficient of the aggregate and the mineral mixture made with it can be obtain machine learning techniques.Thus, the ability to predict the luminosity of a mi will allow, at the design stage of a mineral and asphalt mix, the composition of t be selected in such a way as to achieve the maximum level of luminosity while ing the required mechanical characteristics.The research and analysis resulted lowing conclusions:  The use of machine learning techniques is an excellent tool for modelling nance ratio of aggregates and mineral mixtures; The range of luminance ratio results predicted by the Qd predic model is between 28 mcd•m −2 •lx −1 and 116 mcd•m −2 •lx −1 .In contrast, the RL factor most often obtained a value in the range 35 ÷ 40 mcd•m −2 •lx −1 during the tests.It is the intention of the authors to further validate and calibrate the developed model predicting the luminance coefficient Qd of the aggregate, as well as the mineral mixture.In the next step, the relationships between the aggregate, mineral mix, and mineral-asphalt mixture subjected to wear and tear and the luminance coefficient will be sought.The main objective is to build a DM model to predict the luminance ratio at the design stage of the mineral-asphalt mix.

Conclusions
It should be noted that aggregate resources are not inexhaustible.Therefore, their availability on the market will decrease over time.Currently, mines regulate the amount of extracted aggregate using the principle of sustainable development.Therefore, the amount of aggregate that is extracted depends on the forecasted demand in the long-term perspective.Moreover, it should also be taken into account that in the bituminous mixtures, there are also recycled aggregates, which will also require the assessment of properties and affect the pavement luminance value.Therefore, an effective numerical model will definitely facilitate their selection for the composition of mineral mixtures.The modelling process presented here proved that a very good representation of the luminance coefficient of the aggregate and the mineral mixture made with it can be obtained using machine learning techniques.Thus, the ability to predict the luminosity of a mineral mix will allow, at the design stage of a mineral and asphalt mix, the composition of the mix to be selected in such a way as to achieve the maximum level of luminosity while maintaining the required mechanical characteristics.The research and analysis resulted in the following conclusions: • The use of machine learning techniques is an excellent tool for modelling the luminance ratio of aggregates and mineral mixtures; • The inclusion of a thorough petrographic analysis in the prediction of the aggregate luminance ratio resulted in some improvement in the prediction of the aggregate luminance ratio compared to the case in which its influence was expressed solely by the name of the aggregate; • The mineral that was most decisive in the division between dark and light aggregates was pyroxene, which was characteristic of igneous rocks such as basalt and melaphyre; • The mineral that is probably responsible for the increased reflectivity (nighttime visibility) was mica found in quartzite sandstone, among others; • The best results in terms of surface brightening with Qd > 70 mcd•m −2 •lx −1 were obtained with quartzite sandstone (sedimentary) and granite (igneous), in which the quartz mineral predominated.In contrast, the sedimentary rock class was limestone, which contained mainly calcite; • The amplified random tree (BT) technique used, supported by additional tuning and cross-check (test set) procedures, allowed the construction of a stable BT model characterised by an absolute error of MAE = 5.7 mcd•m −2 •lx −1 and RMSE = 4.4 mcd•m −2 •lx −1 .
The correlation value of the predicted values against the observed values was 87%.The present model effectively eliminated the singularities present, minimising outliers; • The greatest influence on the construction of relationships in the amplified random tree model was the percentage and value of the luminance ratio of mainly the 2/5 and 2/8 fractions; • An analysis of the individual impact of variables on the variability of the predicted BT model indicates that the use of light aggregate fractions with a grain size of 2/5 in quantities >40% or light aggregate 8/11 in quantities of 60% provides a rapid improvement in the degree of lightening of the mineral mixture; • The presence of 5/8 fraction quartzite sandstone showed the best results in terms of brightening the mineral mix.In contrast, a sharp decrease in the luminance coefficient was recorded in mineral mixtures in which basalt aggregate occurring in the 5/8 fraction was used;

•
It is important to note that the machine learning technique adopted was chosen as the most effective due to its quality in predicting the luminance coefficient.This does not mean that other techniques will not be effective.The development of artificial intelligence can provide new models with architectures that will be decidedly better than the BT technique.The authors of this publication are still working on improving the machine learning model.

Figure 1 .
Figure 1.The geometry of the luminance factor: α (angle of observ of incidence and the plane of observation), γ (angle of incidence of observation and the axis of the road on which the luminance fa depending on the observation point P[38]).

Figure 3 .
Figure 3. Coefficient luminance ratio in diffused light RL.Road surfaces generally have RL values in the range of 10 to 30 mcd•m −2 •lx −1 .In comparison, surfaces intended for road marking (containing glass spheres) can usually achieve at least RL = 150 mcd•m −2 •lx −1 .

Figure 4 .
Figure 4.The measuring instrument and the luminance test stand: (a) LTL-X Mark II road retroreflectometer; (b) mould with test sample; (c) scheme of the test stand.

Figure 4 .
Figure 4.The measuring instrument and the luminance test stand: (a) LTL-X Mark II road retroreflectometer; (b) mould with test sample; (c) scheme of the test stand.

Figure 6 .
Figure 6.Grading curves of SMA and AC.

Figure 6 .
Figure 6.Grading curves of SMA and AC.

Figure 7 .
Figure 7. Results of fitting a regression model of gradient-enhanced trees.

Figure 8 .
Figure 8. Probability density of predicted luminance coefficient values Qd relative to aggregate typ based on work [15].

Figure 7 .
Figure 7. Results of fitting a regression model of gradient-enhanced trees.

Figure 7 .
Figure 7. Results of fitting a regression model of gradient-enhanced trees.

Figure 8 .
Figure 8. Probability density of predicted luminance coefficient values Qd relative to aggreg based on work [15].

Figure 8 .
Figure 8. Probability density of predicted luminance coefficient values Qd relative to aggregate type based on work [15].

Figure 9 .
Figure 9. Probability density of predicted RL luminance ratio values relative to aggregate t

Figure 9 .
Figure 9. Probability density of predicted RL luminance ratio values relative to aggregate type.

Figure 9
Figure9indicates the average observed level of road surface reflectivity RL falling within the range of 10 ÷ 30 mcd•m −2 •lx −1 .Basalt aggregate, similar to the Qd, does not introduce any additional improvement in the reflectivity of the pavement.The amphibolite aggregate also has a reflectivity similar to the road surface, although the level of the Qd characteristic was significantly higher than the threshold value at which the pavement is considered 'black'.A significant contribution to reflectivity was observed in the results of limestone, granite and quartzite sandstone aggregate.It is notable that among the results of the reflectance coefficient in artificial light for quartzite sandstone aggregate, there was a certain group of results in quartzite sandstone aggregate with an RL value >70 mcd•m −2 •lx −1 .The observed singularity and the lack of a strong correlation between Qd and RL suggest that the mineralogical composition can definitely contribute to the understanding of the aggregate luminosity phenomenon.

Figure 9 .
Figure 9. Probability density of predicted RL luminance ratio values relative to aggregate type.

Figure 11 .
Figure 11.Mineralogical evaluation of the aggregate.

Figure 11 .
Figure 11.Mineralogical evaluation of the aggregate.

Figure 11 .
Figure 11.Mineralogical evaluation of the aggregate.

Figure 12 .
Figure 12.BT model learning results: (a) optimal number of trees; (b) predictor validity graph.

Figure 12 .
Figure 12.BT model learning results: (a) optimal number of trees; (b) predictor validity graph.

Figure 13 .
Figure 13.Graph of the variability of the projected Qd value of the aggregate.

Figure 13 .
Figure 13.Graph of the variability of the projected Qd value of the aggregate.

Figure 14 .
Figure 14.Algorithm for modelling the luminance coefficient Qd using the BT regression model for the mineral mixture.The task at hand was new, so to select an appropriate DM technique, the tool provided by the Statistica package included in the Data Miner Recipes module was used.Its operation and outcome should be seen primarily as a feasibility study as to the integrity of the dataset, as well as an indication of the technique that is likely to be most effective for luminance ratio prediction.The following four DM regression techniques were initially selected for the task:  Random forest (RT);  Neural network (ANN);  Reinforced random trees (BT);  Classical random trees (C&RT);  Multi adaptive regression splines (MARS).

Figure 14 .
Figure 14.Algorithm for modelling the luminance coefficient Qd using the BT regression model for the mineral mixture.

•
nrounds-controls the maximum number of iterations; • η-controls the learning rate; • γ-controls regularisation (or prevents overfitting); • max depth-controls the depth of the tree; • min.child weight-refers to the minimum number of instances required in a child node; • subsample-controls the number of samples (observations) supplied to a tree.

Figure 15 .
Figure 15.Selected results of tuning model parameters.

Figure 15 .
Figure 15.Selected results of tuning model parameters.
by type of component in the mineral mix (excluding component 1).

Figure 18 .
Figure 18.Comparison of Qdpredic forecast value based on BT and Qdmean.weightedm

Figure 18 .
Figure 18.Comparison of Qd predic forecast value based on BT and Qd mean.weightedmodel.

Figure 19 .
Figure 19.Probability distribution of the predicted diffuse luminance coefficient (Qdpred labelled luminance coefficient under artificial light (RL).

Figure 19 .
Figure 19.Probability distribution of the predicted diffuse luminance coefficient (Qdpredic) and the labelled luminance coefficient under artificial light (RL).

Table 1 .
Aggregate collection used to make mineral mixtures.

Table 2 .
Performance of aggregate set used to create a DM model.

Table 3 .
Assessment of measurement method stability.

Table 3 .
Assessment of measurement method stability.

Table 4 .
Result of fitting the BT model taking into account the analysis of the petrograph variable Qd.
MetricsBT Model with Petrography Analysis The BT Model Included in the Paper by Mazurek et

Table 4 .
Result of fitting the BT model taking into account the analysis of the petrography of the variable Qd.

Table 6 .
A preliminary review of machine learning techniques for the prediction of the Qd feature of a mineral mixture.

Table 7 .
Parameter values after the BT model tuning process (learning set).

Table 7 .
Parameter values after the BT model tuning process (learning set).