Seismic Upgrade of an Existing Reinforced Concrete Building Using Steel Plate Shear Walls (SPSW)

: Steel Plate Shear Walls (SPSW) provide significant lateral load capacity and can be utilized in the seismic retrofit and upgrade of existing reinforced concrete (r/c) buildings. In this study, the application of SPSW to retrofit a r/c building designed according to older seismic provisions is presented. Three different options to model SPSW are utilized, i.e., by equivalent braces, by finite elements, and by membrane elements, seeking not only to appropriately simulate the actual behavior of the SPSW but also to achieve the desired seismic behavior of the retrofitted building. Specific seismic response indices, including plastic hinge formations, are derived by non-linear time-history analyses in order to assess the seismic behavior of the retrofitted r/c building. Inspection of the results provided by non-linear analyses in conjunction with the different modeling options of the SPSW leads to the conclusion that the model with the membrane elements exhibits the best performance, implying that for the seismic retrofit and upgrade of existing r/c buildings, the use of membrane elements to model the SPSW is recommended.


Introduction
The majority of reinforced concrete (r/c) buildings in Greece, for residential, office, and other purposes, were constructed before 1985, and their seismic design was performed on the basis of the 1959 Greek Seismic Code [1].These r/c buildings normally do not possess the desirable characteristics that modern seismic codes envisage through the application of certain design criteria.Consequently, these r/c buildings are considered susceptible to seismic damages or failures and necessitate an in-depth evaluation in order to assess the feasibility of their possible seismic retrofit and upgrade.
The methods used in seismic retrofit and upgrade of existing r/c buildings in Greece and elsewhere are described in detail in [2] and commonly involve r/c and FRP (fiberreinforced polymer) jacketing, r/c shear walls, strengthening of infill panels and steel braces, as well as the mature technologies of base isolation and added damping devices.Despite the versatility and diversity of the seismic retrofit options offered by steel elements, it seems that their use has been restricted to steel braces, usually positioned in a concentric (diagonal or cross-diagonal) manner with respect to a r/c frame, whereas steel jackets and plates have been almost totally substituted by FRP materials [2].
It is true that modern seismic codes, e.g., [3], do not promote specific steel elements for the seismic retrofit and upgrade of existing r/c buildings.The reason is that extensive numerical and experimental data that certify the benefits behind the use of many novel steel elements in seismic retrofits and upgrades of existing r/c buildings became available after the initiation of such codes.The most representative example of such steel elements is the buckling-restrained brace [4][5][6][7][8], even though other steel systems have also evolved or seem to have potential [9][10][11][12].
Appl.Sci.2024, 14, 443 2 of 22 A steel element of special interest for the seismic retrofit and upgrade of existing r/c buildings is the Steel Plate Shear Wall (SPSW).The use of SPSW in steel structures as a lateral force-resisting system enjoys popularity in several countries, e.g., Japan, Mexico, Canada, and the U.S.A., and detailed design criteria are available in ANSI/AISC 341-22 [13] and CSA S16-19 [14] design standards.With respect to the application of SPSW in the seismic retrofit of existing r/c buildings, to the best of the authors' knowledge, one can consult [15][16][17].Among the various numerical and experimental works dealing with the seismic retrofit and upgrade of r/c buildings with SPSW, one can name those in [18][19][20][21][22][23].
A key issue with respect to the anticipated seismic performance of a retrofitted SPSW r/c building is the interaction achieved between the steel and the existing r/c system, i.e., the actual forces transferred between the two materials.
A typical SPSW system, shown in Figure 1, consists of a thin steel web-plate with a common thickness ranging from 5 to 25 mm, two boundary columns, and horizontal boundary beams [17].The boundary columns are called vertical boundary elements (VBE), and the beams are called horizontal boundary elements (HBE).With respect to terminology, in steel structures, the term SPSW is used if standard steel sections are employed as HBEs and VBEs.However, when referring to a r/c frame, two configurations can be accomplished: (i) in the first one, a metal sheet or plate is inserted between the existent r/c beams and columns that essentially play the role of the HBEs and the VBEs; (ii) in the second one, the steel plate is inserted between added steel columns (HBEs), implying that the resulting SPSW does not occupy the entire bay span of the r/c frame.Taking into account the relevant literature for both configurations (i) and (ii) studied in the following, it is decided for reasons of uniformity to keep the term SPSW.
Appl.Sci.2024, 14, x FOR PEER REVIEW 2 of 22 A steel element of special interest for the seismic retrofit and upgrade of existing r/c buildings is the Steel Plate Shear Wall (SPSW).The use of SPSW in steel structures as a lateral force-resisting system enjoys popularity in several countries, e.g., Japan, Mexico, Canada, and the U.S.A., and detailed design criteria are available in ANSI/AISC 341-22 [13] and CSA S16-19 [14] design standards.With respect to the application of SPSW in the seismic retrofit of existing r/c buildings, to the best of the authors' knowledge, one can consult [15][16][17].Among the various numerical and experimental works dealing with the seismic retrofit and upgrade of r/c buildings with SPSW, one can name those in [18][19][20][21][22][23].A key issue with respect to the anticipated seismic performance of a retrofitted SPSW r/c building is the interaction achieved between the steel and the existing r/c system, i.e., the actual forces transferred between the two materials.
A typical SPSW system, shown in Figure 1, consists of a thin steel web-plate with a common thickness ranging from 5 to 25 mm, two boundary columns, and horizontal boundary beams [17].The boundary columns are called vertical boundary elements (VBE), and the beams are called horizontal boundary elements (HBE).With respect to terminology, in steel structures, the term SPSW is used if standard steel sections are employed as HBEs and VBEs.However, when referring to a r/c frame, two configurations can be accomplished: (i) in the first one, a metal sheet or plate is inserted between the existent r/c beams and columns that essentially play the role of the HBEs and the VBEs; (ii) in the second one, the steel plate is inserted between added steel columns (HBEs), implying that the resulting SPSW does not occupy the entire bay span of the r/c frame.Taking into account the relevant literature for both configurations (i) and (ii) studied in the following, it is decided for reasons of uniformity to keep the term SPSW.The strength of the connection of the SPSW with the surrounding members has to be greater than the strength of the SPSW itself.This way, the SPSW yields before yielding of the surrounding members occurs.The steel plate can be stiffened or unstiffened.To reduce the slenderness of the steel plate, stiffeners are added in a vertical or horizontal configuration, even in some cases in a diagonal manner, providing, thus, the buckling strength needed to allow shear yielding of the plate.
The mechanics of a stiffened or unstiffened SPSW are described in [17], revealing the development of a tension field in the plate as the main mechanical characteristic.Unstiffened SPSWs are capable of resisting seismic loads by developing a diagonal tension field with an optimum inclination angle of α = 45 • .In slender unstiffened SPSWs, the tension field is formed after the buckling of the plate but before its shear yielding, whereas in stiffened SPSWs, the plate yields and then buckles.However, depending on the spacing and thickness of the stiffeners, the tension-field action in stiffened SPSW may take place when buckling occurs and before shear yielding [17].
SPSWs do not significantly increase the mass of the structure and can be easily replaced in case of failure.Moreover, their erection process is faster and easier than with other conventional retrofitting techniques [24].From the perspective of capacity design [25], the HBEs (beams) should resist the demands of the tension field yielding of the steel plate, and the VBEs (columns) should resist the demands of the tension field yielding and flexural yielding of the HBEs.Therefore, it is important that the boundary elements have adequate strength and stiffness to ensure the full development of the tension field.
Retrofit of r/c buildings is a highly active research domain and covers several hazard scenarios such as fire, seismic events, and explosions, e.g., [26][27][28].Attempting to remobilize the interest of practicing engineers and researchers regarding the application of SPSW for seismic retrofit and upgrade purposes, this paper investigates the effectiveness of the SPSW on an existing r/c building designed by older seismic provisions.In particular, expanding the knowledge gained by previous works in the field [18][19][20][21][22][23], what this present study seeks to make clear is how the modeling and configuration of the SPSW have an impact on the desired seismic performance of the existing r/c building.To be sure in capturing the effects of modeling and configuration of SPSW, three-dimensional non-linear time-history (NLTH) analyses are conducted, thus, from a computational point of view, the best option available for seismic response purposes is selected.On the basis of specific seismic response results obtained by NLTH analyses, including plastic hinge formations, and letting aside any issues related to fabrication and cost, conclusions about the modeling, configuration, and effectiveness of the SPSW for r/c buildings similar to the type studied herein are drawn.

Description of the r/c Building
The r/c building under study is a 3-story building located in Amaliada, Greece, and its design was carried out in 1976 on the basis of the requirements of the 1959 seismic code [1].A common characteristic of r/c buildings designed by this seismic code is their poor ductile behavior and, in many cases, the scarcity of enough transverse (shear) steel reinforcement for columns.Thus, r/c buildings designed according to [1] cannot conform to ductile seismic requirements [2,3] unless a case-dependent seismic upgrade strategy is employed.The whole set of architectural plans and formworks was available at the time of this study and it is indicatively shown in Figures 2-4.According to Figures 2 and 3 and more specifically section AA', the building has an asymmetrical floor plan and a total height of 10.65 m.The first storey is 4.15 m high, while the second and third storeys have a height of 3.25 m each.
The dimensions (in cm) of all beams are 20/50, whereas those of columns are 35/35 for the first storey and 30/30 for the second and third storeys.The longitudinal steel reinforcement of beams and columns is presented in Tables 1 and 2, respectively.It is also noted that the transverse reinforcement is Φ6/220 (in mm) for beams and Φ8/150 (in mm) for columns.The thickness of the floor slabs is 14 cm.The material properties and the detailing rules of the building align with the seismic provisions of 1959 [1].More specifically, the grades of concrete and steel reinforcement are C12/15 and S220, respectively.With respect to the loads considered for the design of the building, the dead and live loads on the slabs are 0.8 kN/m 2 and 2.0 kN/m 2 , respectively, whereas, for the cantilever slabs, a live load equal to 5.0 kN/m 2 is assumed.The dead loads from infills (9.9 kN/m for the external ones and 5.8 kN/m for the internal ones) are distributed to the beams.
Appl.Sci.2024, 14, x FOR PEER REVIEW 4 of 22 detailing rules of the building align with the seismic provisions of 1959 [1].More specifically, the grades of concrete and steel reinforcement are C12/15 and S220, respectively.With respect to the loads considered for the design of the building, the dead and live loads on the slabs are 0.8 kN/m 2 and 2.0 kN/m 2 , respectively, whereas, for the cantilever slabs, a live load equal to 5.0 kN/m 2 is assumed.The dead loads from infills (9.9 kN/m for the external ones and 5.8 kN/m for the internal ones) are distributed to the beams.Appl.Sci.2024, 14, x FOR PEER REVIEW 4 of 22 detailing rules of the building align with the seismic provisions of 1959 [1].More specifically, the grades of concrete and steel reinforcement are C12/15 and S220, respectively.With respect to the loads considered for the design of the building, the dead and live loads on the slabs are 0.8 kN/m 2 and 2.0 kN/m 2 , respectively, whereas, for the cantilever slabs, a live load equal to 5.0 kN/m 2 is assumed.The dead loads from infills (9.9 kN/m for the external ones and 5.8 kN/m for the internal ones) are distributed to the beams.

Seismic Analysis of the r/c Building
On the basis of the data presented in the previous section, a numerical model of the r/c building was created in SAP 2000 [29], and it is shown in Figure 5.In this model, frame elements are used for beams and columns and shell elements for the floor slabs.Concrete cracking is conservatively taken into account by considering for all members an effective stiffness equal to 50% of the gross stiffness.The position of the staircase is found not to be critical for the seismic response of the r/c building, and, thus, it is not included in the numerical model.Infills are included in the model, but only as loads to the beams.The r/c building is assumed to be fixed-base (base fixity is denoted with green symbols in the figures that follow), and, hence, soil-structure-interaction effects are absent.

Seismic Analysis of the r/c Building
On the basis of the data presented in the previous section, a numerical model of the r/c building was created in SAP 2000 [29], and it is shown in Figure 5.In this model, frame elements are used for beams and columns and shell elements for the floor slabs.Concrete cracking is conservatively taken into account by considering for all members an effective stiffness equal to 50% of the gross stiffness.The position of the staircase is found not to be critical for the seismic response of the r/c building, and, thus, it is not included in the numerical model.Infills are included in the model, but only as loads to the beams.The r/c building is assumed to be fixed-base (base fixity is denoted with green symbols in the figures that follow), and, hence, soil-structure-interaction effects are absent.It is then assumed that the r/c building must resist the seismic load defined by the design spectrum of EC8 [30] for a peak ground acceleration (PGA) equal to 0.24 g (representative of the broader area [31] where the r/c building under study lies), soil class B, importance factor γ = 1.0, and behavior factor q = 1.5.Modal response spectrum analysis of the fixed-base r/c building is performed using the 100-30% spectral combination rule, and the storey shears in both horizontal directions of the building are computed.These storey shears are used for the design of the SPSW in the following and read: 988.113 kN and 926.853 kN for the first storey in the x and y directions, respectively; 729.937 kN and 685.458 kN for the second storey in the x and y directions, respectively; and 292.945 kN and 279.892 kN for the third storey in the x and y directions, respectively.The fundamental period of the r/c building is Τ1 = 0.837 s.
Next, to identify the potential seismic damage in the critical regions of the beams and columns of the r/c building, NLTH analyses are conducted using three seismic motions It is then assumed that the r/c building must resist the seismic load defined by the design spectrum of EC8 [30] for a peak ground acceleration (PGA) equal to 0.24 g (representative of the broader area [31] where the r/c building under study lies), soil class B, importance factor γ = 1.0, and behavior factor q = 1.5.Modal response spectrum analysis of the fixed-base r/c building is performed using the 100-30% spectral combination rule, and the storey shears in both horizontal directions of the building are computed.These storey shears are used for the design of the SPSW in the following and read: 988.113 kN and 926.853 kN for the first storey in the x and y directions, respectively; 729.937 kN and 685.458 kN for the second storey in the x and y directions, respectively; and 292.945 kN and 279.892 kN for the third storey in the x and y directions, respectively.The fundamental period of the r/c building is T 1 = 0.837 s.
Next, to identify the potential seismic damage in the critical regions of the beams and columns of the r/c building, NLTH analyses are conducted using three seismic motions for which their response spectrum is compatible with the aforementioned design spectrum.The two horizontal components of these seismic motions are used interchangeably with respect to the two horizontal axes of the r/c building.Thus, in total, six NLTH analyses are executed assuming: (i) both material and geometrical nonlinearities; (ii) the innate viscous damping of the r/c building to be 3% and the (Rayleigh) damping matrix to be defined using the well-known mass and stiffness proportionality factors; (iii) point plastic hinges at the ends of beams and columns in order to take into account their inelastic behavior.These plastic hinges to beams are formed by bending moments, whereas those to columns are formed by the combination of axial force and bending moments [29,32].A flexure-shear failure condition is also considered for columns [29,32].
The NLTH analyses revealed almost similar patterns regarding the number of plastic hinge formations on the beams and columns of the r/c building.Figure 6 displays these plastic hinges for the case of the first seismic motion, where one can notice unwanted plastic hinges not only at the top end of the columns of the first storey but also at both ends of the columns of the second storey.Besides the excessive plastic hinge rotation at the bottom end of one column of the first storey, the plastic hinges to the columns of the first two storeys are classified in the IO (Immediate Occupancy)-LS (Life Safety) performance level range according to the acceptance criteria of [32].In the figures that follow, the legends B, IO, LS, CP, C, etc. are in accordance with the normalized force versus deformation curve of [32].The maximum values for transient interstorey drift ratios (IDRs), residual interstorey drift ratios (RIDR), and base shear are listed in Table 3.The definition and calculation of IDR, RIDR, and base shear in the context of time-domain seismic analysis are described in [33].In Table 3, symbols of the form "1a" and "1b" are used to denote the two cases of using the two horizontal components of the first seismic motion interchangeably with respect to the horizontal axes of the building.More specifically, "1a" denotes that the 1st horizontal component of the seismic motion is applied along the x direction of the building and the 2nd horizontal component is applied along the y direction, whereas "1b" denotes the opposite application of these components with respect to the x and y directions of the building.
The maximum RIDR is 1.37%, which is well beyond the maximum allowable value of 0.5% usually considered [34].According to the results presented in Table 3 and the plastic hinge formation shown in Figure 6, a soft-storey mechanism is anticipated to occur.A retrofit scheme using SPSW is proposed in the next section in order to improve the overall seismic behavior of the r/c building.
for which their response spectrum is compatible with the aforementioned design spectrum.The two horizontal components of these seismic motions are used interchangeably with respect to the two horizontal axes of the r/c building.Thus, in total, six NLTH analyses are executed assuming: (i) both material and geometrical nonlinearities; (ii) the innate viscous damping of the r/c building to be 3% and the (Rayleigh) damping matrix to be defined using the well-known mass and stiffness proportionality factors; (iii) point plastic hinges at the ends of beams and columns in order to take into account their inelastic behavior.These plastic hinges to beams are formed by bending moments, whereas those to columns are formed by the combination of axial force and bending moments [29,32].A flexure-shear failure condition is also considered for columns [29,32].
The NLTH analyses revealed almost similar patterns regarding the number of plastic hinge formations on the beams and columns of the r/c building.Figure 6 displays these plastic hinges for the case of the first seismic motion, where one can notice unwanted plastic hinges not only at the top end of the columns of the first storey but also at both ends of the columns of the second storey.Besides the excessive plastic hinge rotation at the bottom end of one column of the first storey, the plastic hinges to the columns of the first two storeys are classified in the IO (Immediate Occupancy)-LS (Life Safety) performance level range according to the acceptance criteria of [32].In the figures that follow, the legends B, IO, LS, CP, C, etc. are in accordance with the normalized force versus deformation curve of [32].The maximum values for transient interstorey drift ratios (IDRs), residual interstorey drift ratios (RIDR), and base shear are listed in Table 3.The definition and calculation of IDR, RIDR, and base shear in the context of time-domain seismic analysis are described in [33].In Table 3, symbols of the form "1a" and "1b" are used to denote the two cases of using the two horizontal components of the first seismic motion interchangeably with respect to the horizontal axes of the building.More specifically, "1a" denotes that the 1st horizontal component of the seismic motion is applied along the x direction of the building and the 2nd horizontal component is applied along the y direction, whereas "1b" denotes the opposite application of these components with respect to the x and y directions of the building.
The maximum RIDR is 1.37%, which is well beyond the maximum allowable value of 0.5% usually considered [34].According to the results presented in Table 3 and the plastic hinge formation shown in Figure 6, a soft-storey mechanism is anticipated to occur.A retrofit scheme using SPSW is proposed in the next section in order to improve the overall seismic behavior of the r/c building.

Modeling of the SPSWs
The SPSWs are configured only at the external frames of the building and are continuous along its height.Taking into account that three modeling options for SPSWs are provided in [17], NLTH analyses are carried out separately for each modeling option in order to assess its effect on the seismic response of the building.These modeling options are briefly described in the following: It is recalled that the storey shears found by modal response spectrum analyses are used in the design of the SPSWs.

Equivalent Brace Model (EBM)
Each SPSW is modeled by a diagonal tension-only brace, designed according to [17].The mechanics behind this model are that a SPSW behaves like a tension-only brace, assuming the inclination angle of the tension field to be α = 45 • .The thickness of the steel plate is determined according to the following equation [17] where L cf is the clear distance between the VBEs (columns), f y is the yield stress of the steel web-plate (herein considered 235 MPa), and V u is the shear force taken from the modal response spectrum analysis.The thickness of the SPSW should be specified by the equation [17] min(L, h) where L and h are the length and height of the web-plate, respectively, and E is the modulus of elasticity of steel.The resulting thickness is t w = 5.0 mm for each plate.ANSI/AISC 341-22 [13] and CSA S16-19 [14] design standards require that the length-to-height (L/h) ratio of the web-plates satisfy 0.8 < L/h ≤ 2.5.Additionally, the moment of inertia I c of the VBEs should satisfy the following equation [13,17] Thus, the area A of the equivalent tension brace is calculated by where θ is the angle between the vertical and longitudinal axes of the equivalent diagonal brace, L is the distance between the centerlines of the VBEs, and Ω s = 1.2 is the system overstrength factor.The resulting brace sections are assumed to be of CHS type, and the resulting sections are CHS 273/16 for the first storey and CHS 244.5/16 for the second and third storeys.The model of the r/c building with SPSWs modeled by equivalent braces is shown in Figure 7.The fundamental period of the r/c building in Figure 7 is T 1 = 0.739 s.
Appl.Sci.2024, 14, x FOR PEER REVIEW 9 of 22 where θ is the angle between the vertical and longitudinal axes of the equivalent diagonal brace, L is the distance between the centerlines of the VBEs, and Ωs = 1.2 is the system overstrength factor.The resulting brace sections are assumed to be of CHS type, and the resulting sections are CHS 273/16 for the first storey and CHS 244.5/16 for the second and third storeys.The model of the r/c building with SPSWs modeled by equivalent braces is shown in Figure 7.The fundamental period of the r/c building in Figure 7 is Τ1 = 0.739 s.

Finite Element Model (FEM)
Each SPSW is simulated by shell elements.The thickness of the shell elements is that found above by the application of Equations ( 1) and ( 2), i.e., tw = 5 mm.This model is shown in Figure 8.The VBEs needed for the SPSW are essentially offered by the r/c columns to which an additional one-sided steel sheet or plate is attached.The fundamental period of the r/c building in Figure 8 is Τ1 = 0.773 s.An additional configuration of the SPSW is introduced at this point and displayed in Figure 9.This configuration permits the insertion of the SPSWs in both horizontal directions of the building.More specifically, according to Figure 9, the number of SPSWs remains the same, but in comparison to the model shown in Figure 8, SPSWs with smaller dimensions are employed in order not to occupy the entire bay span.This configuration of SPSWs is achieved with the aid of steel columns with flanged profiles.Thus, the webplates are rigidly connected to HEA180 columns in the first storey and to HEA160 columns in the second and third storeys.

Finite Element Model (FEM)
Each SPSW is simulated by shell elements.The thickness of the shell elements is that found above by the application of Equations ( 1) and ( 2), i.e., t w = 5 mm.This model is shown in Figure 8.The VBEs needed for the SPSW are essentially offered by the r/c columns to which an additional one-sided steel sheet or plate is attached.The fundamental period of the r/c building in Figure 8 is T 1 = 0.773 s.
where θ is the angle between the vertical and longitudinal axes of the equivalent diagonal brace, L is the distance between the centerlines of the VBEs, and Ωs = 1.2 is the system overstrength factor.The resulting brace sections are assumed to be of CHS type, and the resulting sections are CHS 273/16 for the first storey and CHS 244.5/16 for the second and third storeys.The model of the r/c building with SPSWs modeled by equivalent braces is shown in Figure 7.The fundamental period of the r/c building in Figure 7 is Τ1 = 0.739 s.

Finite Element Model (FEM)
Each SPSW is simulated by shell elements.The thickness of the shell elements is that found above by the application of Equations ( 1) and ( 2), i.e., tw = 5 mm.This model is shown in Figure 8.The VBEs needed for the SPSW are essentially offered by the r/c columns to which an additional one-sided steel sheet or plate is attached.The fundamental period of the r/c building in Figure 8 is Τ1 = 0.773 s.An additional configuration of the SPSW is introduced at this point and displayed in Figure 9.This configuration permits the insertion of the SPSWs in both horizontal directions of the building.More specifically, according to Figure 9, the number of SPSWs remains the same, but in comparison to the model shown in Figure 8, SPSWs with smaller dimensions are employed in order not to occupy the entire bay span.This configuration of SPSWs is achieved with the aid of steel columns with flanged profiles.Thus, the webplates are rigidly connected to HEA180 columns in the first storey and to HEA160 columns in the second and third storeys.An additional configuration of the SPSW is introduced at this point and displayed in Figure 9.This configuration permits the insertion of the SPSWs in both horizontal directions of the building.More specifically, according to Figure 9, the number of SPSWs remains the same, but in comparison to the model shown in Figure 8, SPSWs with smaller dimensions are employed in order not to occupy the entire bay span.This configuration of SPSWs is achieved with the aid of steel columns with flanged profiles.Thus, the web-plates are rigidly connected to HEA180 columns in the first storey and to HEA160 columns in the second and third storeys.The length of the SPSWs is 2.0 m in the y direction and 1.5 m in the x direction.It should be noted that the length-to-height ratio does not satisfy the condition 0.8 < L/h ≤ 2.5 and according to the [14] the use of intermediate stiffeners is suggested.In this case, the required web-plate thickness is determined by the following equation (the shear force Vu is known or can be estimated) The minimum selected thickness is tw = 5 mm for each plate.Stiffeners are ignored in the current study, leading to more conservative results due to the lower stiffness of the plate.The fundamental period of the r/c building in Figure 9 is Τ1 = 0.370 s.

Orthotropic Membrane Model (OMM)
The web-plates of the SPSWs shown in Figure 9 are now modeled by membrane elements.To take into account the difference between the tension and compression strength of the web-plates, an orthotropic steel material is considered.The orthotropic membrane model depends on the inclination angle, leading to a reorientation of the local axes of the membrane elements.Therefore, the local axes of the membrane elements are rotated by 45°.Moreover, the stiffness value along the axis that corresponds to the compression diagonal is degraded to 2%, the Poisson ratio is set to v12 = 0, and the shear modulus is set equal to G = 0.This way, the assumed tension-field action of the web-plates is adequately represented.

Equivalent Brace Model (EBM)
The braces resist only tensile axial loads as expected, however, contrary to the desired behavior of the SPSWs, they do not yield.The maximum values for IDRs, RIDRs, and base shear are listed in Table 4 (the symbols "1a", "1b", etc. have been previously explained).In comparison to the results presented in Section 3 for the non-retrofitted building, the maximum RIDR is reduced to 0.41% < 0.50%, but the maximum base shear is significantly increased and reaches 1934 kN.Therefore, modeling the SPSWs with EBMs leads to a stiffer building and, thus, to reduced displacements; nevertheless, a soft-storey mechanism is still anticipated to occur.With reference to Figure 10 (plastic hinge excursions for the worst seismic motion "1b") and on the basis of the acceptance criteria of [29], plastic hinges to columns for all six NLTH analyses performed either remain in the range defined by the IO-LS performance levels or surpass the LS performance level.The length of the SPSWs is 2.0 m in the y direction and 1.5 m in the x direction.It should be noted that the length-to-height ratio does not satisfy the condition 0.8 < L/h ≤ 2.5 and according to the [14] the use of intermediate stiffeners is suggested.In this case, the required web-plate thickness is determined by the following equation (the shear force V u is known or can be estimated) The minimum selected thickness is t w = 5 mm for each plate.Stiffeners are ignored in the current study, leading to more conservative results due to the lower stiffness of the plate.The fundamental period of the r/c building in Figure 9 is T 1 = 0.370 s.

Orthotropic Membrane Model (OMM)
The web-plates of the SPSWs shown in Figure 9 are now modeled by membrane elements.To take into account the difference between the tension and compression strength of the web-plates, an orthotropic steel material is considered.The orthotropic membrane model depends on the inclination angle, leading to a reorientation of the local axes of the membrane elements.Therefore, the local axes of the membrane elements are rotated by 45 • .Moreover, the stiffness value along the axis that corresponds to the compression diagonal is degraded to 2%, the Poisson ratio is set to v 12 = 0, and the shear modulus is set equal to G = 0.This way, the assumed tension-field action of the web-plates is adequately represented.

Equivalent Brace Model (EBM)
The braces resist only tensile axial loads as expected, however, contrary to the desired behavior of the SPSWs, they do not yield.The maximum values for IDRs, RIDRs, and base shear are listed in Table 4 (the symbols "1a", "1b", etc. have been previously explained).In comparison to the results presented in Section 3 for the non-retrofitted building, the maximum RIDR is reduced to 0.41% < 0.50%, but the maximum base shear is significantly increased and reaches 1934 kN.Therefore, modeling the SPSWs with EBMs leads to a stiffer building and, thus, to reduced displacements; nevertheless, a soft-storey mechanism is still anticipated to occur.With reference to Figure 10 (plastic hinge excursions for the worst seismic motion "1b") and on the basis of the acceptance criteria of [29], plastic hinges to columns for all six NLTH analyses performed either remain in the range defined by the IO-LS performance levels or surpass the LS performance level.

Finite Element Model (FEM)
The results of the retrofitted building shown in Figure 8 are described first.The maximum values for IDRs, RIDR, and base shear are listed in Table 5, and in comparison to the results presented in sections 3 (for the non-retrofitted building) and 5.1 (for the retrofitted building-EBM case), the maximum RIDR and base shear are increased to 1.71% >

Finite Element Model (FEM)
The results of the retrofitted building shown in Figure 8 are described first.The maximum values for IDRs, RIDR, and base shear are listed in Table 5, and in comparison to the results presented in Section 3 (for the non-retrofitted building) and Section 5.1 (for the retrofitted building-EBM case), the maximum RIDR and base shear are increased to 1.71% > 0.50% and 2680 kN (i.e., by 38.6%), respectively.
Figure 11 displays the worst plastic hinge excursions (coming from the seismic motion "1b").According to the acceptance criteria of [29], plastic hinges to columns for five NLTH analyses performed remain in the range defined by the IO-LS performance levels, and in one NLTH analysis, they surpass the LS performance level.In general, contrary to the EBM case described in the previous section, modeling of the SPSWs with FEMs (Figure 8) indicates ductile behavior of the building and reveals no or small damage to several beams and columns in almost all NLTH analyses performed.Table 6 presents the Von Mises stresses and the maximum shear stresses of the SPSWs, demonstrating that the SPSWs have not been fully utilized, as none of the plates yielded.11 displays the worst plastic hinge excursions (coming from the seismic motion "1b").According to the acceptance criteria of [29], plastic hinges to columns for five NLTH analyses performed remain in the range defined by the IO-LS performance levels, and in one NLTH analysis, they surpass the LS performance level.In general, contrary to the EBM case described in the previous section, modeling of the SPSWs with FEMs (Figure 8) indicates ductile behavior of the building and reveals no or small damage to several beams and columns in almost all NLTH analyses performed.Table 6 presents the Von Mises stresses and the maximum shear stresses of the SPSWs, demonstrating that the SPSWs have not been fully utilized, as none of the plates yielded.
The results of the retrofitted building shown in Figure 9 are described next.The maximum values for IDRs, RIDR, and base shear are listed in Table 7, and in comparison to the results presented in Section 3 (for the non-retrofitted building) and the previous model (Figure 8), the maximum RIDR is drastically decreased to 0.036% < 0.5% and the maximum base shear reduces to 2066 kN (i.e., by 23%).The inelastic behavior of the building is improved, and as revealed by the plastic hinge excursions shown in Figure 12 (worst case), plastic hinges to columns for all six NLTH analyses performed remain below the range defined by the LS.The results of the retrofitted building shown in Figure 9 are described next.The maximum values for IDRs, RIDR, and base shear are listed in Table 7, and in comparison to the results presented in Section 3 (for the non-retrofitted building) and the previous model (Figure 8), the maximum RIDR is drastically decreased to 0.036% < 0.5% and the maximum base shear reduces to 2066 kN (i.e., by 23%).The inelastic behavior of the building is improved, and as revealed by the plastic hinge excursions shown in Figure 12 (worst case), plastic hinges to columns for all six NLTH analyses performed remain below the range defined by the LS.The Von Mises stresses and the maximum shear stresses of the SPSWs are listed in Table 8, demonstrating that with respect to the model of Figure 8, the SPSWs are certainly better utilized, and one of them yields (Figure 13).

Comparison of EBM and FEM
From the results presented in the two previous sections, one concludes that the modeling of SPSWs by FEM indicates the ductile behavior of the building and an increase in its lateral load capacity (in terms of base shear).On the contrary, the EBM does not lead

Comparison of EBM and FEM
From the results presented in the two previous sections, one concludes that the modeling of SPSWs by FEM indicates the ductile behavior of the building and an increase in its lateral load capacity (in terms of base shear).On the contrary, the EBM does not lead to the expected tension-field action, as the equivalent diagonal braces do not yield even though the lateral load capacity of the building increases.Furthermore, the EBM leads to undesirable plastic hinge excursions in 4 out of 6 NLTH analyses.On the other hand, the FEM leads to undesirable plastic hinge excursions only in one NLTH analysis and only for the long configuration of SPSWs.
For ease of comparison regarding the number of plastic hinges formed and their performance classification, Tables 9-11 are provided for the worst seismic motion, "1b."In these Tables, the reference (non-retrofitted) and the retrofitted (EBM and FEM) building models are included.In particular, for the FEM building models, i and ii are used to denote the long (Figure 8) and short (Figure 9), respectively, configuration of the SPSWs.It is also noted that the symbol B denotes almost elastic behavior, the symbols C and CP denote the collapse and collapse prevention performance levels, respectively, whereas the dash (-) denotes that no plastic hinge excursion occurs.In order to evaluate the tension-field action in the OMM, the maximum Von Mises and normal stresses are listed in Table 13, where S11 and S12 correspond to tensile and compressive stresses, respectively.Figures 15 and 16 display the Von Mises stresses and principal tensile stresses, respectively, for the worst seismic motion "1b".From the results of Table 13 and in conjunction with Figures 15 and 16, yielding of the web-plate of the SPSW is achieved, confirming the ductile behavior sought; nevertheless, the ultimate strength of 360 MPa (steel material S235) is considerably exceeded for seismic motion "1b".To ensure that the ultimate strength of the web-plates of the SPSW is not exceeded, the NLTH analyses are repeated, assuming the thickness t of the web-plate for all SPSWs to be 9.0 mm.Modal analysis is performed, and the fundamental period of the building is now Τ1 = 0.406 s.The maximum values from NLTH analyses for IDRs, RIDR and base shear are presented in Table 14 and are compared with those of Table 12.One easily notices that the maximum RIDR increases to 0.093% < 0.5%, and the maximum base shear also increases to 2202 kN (i.e., by 9.5%).
Figure 17 displays the worst plastic hinge distribution obtained from the NLTH analyses (seismic motion "1b").A comparison of the number of plastic hinge excursions in Figures 14 and 17 reveals that the increase in thickness from 5.0 to 9.0 mm leads to slightly To ensure that the ultimate strength of the web-plates of the SPSW is not exceeded, the NLTH analyses are repeated, assuming the thickness t of the web-plate for all SPSWs to be 9.0 mm.Modal analysis is performed, and the fundamental period of the building is now T 1 = 0.406 s.The maximum values from NLTH analyses for IDRs, RIDR and base shear are presented in Table 14 and are compared with those of Table 12.One easily notices that the maximum RIDR increases to 0.093% < 0.5%, and the maximum base shear also increases to 2202 kN (i.e., by 9.5%).Figure 17 displays the worst plastic hinge distribution obtained from the NLTH analyses (seismic motion "1b").A comparison of the number of plastic hinge excursions in Figures 14 and 17 reveals that the increase in thickness from 5.0 to 9.0 mm leads to slightly better behavior.If plastic hinge excursions for the rest of seismic motions are compared (the corresponding figures are not shown herein for space reasons), one concludes that this increase in thickness certainly improves the behavior of the building and, in all likelihood, the exhibition of a soft-storey mechanism is avoided.The maximum Von Mises and normal (tensile and compressive) stresses are listed in Table 15, whereas Figures 18 and 19 display the Von Mises stresses and principal tensile stresses, respectively, for the worst seismic motion "1b".From the results of Table 15 and in conjunction with Figures 18 and 19, yielding of the web-plate of the SPSW is now achieved for three seismic motions, but the ultimate strength of 360 MPa is not exceeded.Therefore, the desired behavior of the retrofitted SPSWs r/c building is obtained for all seismic motions considered.15, whereas Figures 18 and 19 display the Von Mises stresses and principal tensile stresses, respectively, for the worst seismic motion "1b".From the results of Table 15 and in conjunction with Figures 18 and 19, yielding of the web-plate of the SPSW is now achieved for three seismic motions, but the ultimate strength of 360 MPa is not exceeded.Therefore, the desired behavior of the retrofitted SPSWs r/c building is obtained for all seismic motions considered.Taking into account that for the seismic retrofit of existing r/c buildings in seismic regions, energy dissipation is sought [2,3], the SPSW should be designed to yield but not fail.On the other hand, if only added stiffness and/or strength are required for seismic retrofit purposes, then yielding of the SPSW is not allowed, keeping in mind that the thickness of the SPSW depends on the geometric properties of the VBEs and HBEs [13,14,17].Taking into account that for the seismic retrofit of existing r/c buildings in seismic regions, energy dissipation is sought [2,3], the SPSW should be designed to yield but no fail.On the other hand, if only added stiffness and/or strength are required for seismic retrofit purposes, then yielding of the SPSW is not allowed, keeping in mind that the thick ness of the SPSW depends on the geometric properties of the VBEs and HBEs [13,14,17].

Conclusions
This paper investigates the seismic retrofit and upgrade of an existing r/c building using SPSWs.SPSWs are able to provide both stiffness and ductility; however, their actua Taking into account that for the seismic retrofit of existing r/c buildings in seismic regions, energy dissipation is sought [2,3], the SPSW should be designed to yield but not fail.On the other hand, if only added stiffness and/or strength are required for seismic retrofit purposes, then yielding of the SPSW is not allowed, keeping in mind that the thickness of the SPSW depends on the geometric properties of the VBEs and HBEs [13,14,17].

Conclusions
This paper investigates the seismic retrofit and upgrade of an existing r/c building using SPSWs.SPSWs are able to provide both stiffness and ductility; however, their actual behavior has to be appropriately represented in the numerical model.Additionally, the placement and configuration of the SPSWs is a critical factor concerning their contribution to the anticipated seismic performance of the building.
Three different options are utilized herein to model SPSWs, and the seismic performance of the retrofitted r/c building is assessed by a number of NLTH analyses.From the results of these analyses, in terms of specific seismic response indices and plastic hinge formations to the members of the building, it is concluded that short-length SPSWs in conjunction with an orthotropic membrane model (OMM) for them provide the best option.As an alternative good option, one may select a finite element model (FEM) instead of the OMM; on the other hand, the equivalent brace model (EBM) is not recommended.Taking into account that discretization by membrane elements in conjunction with orthotropic material properties are common options in all modern structural analysis software, the implementation of an OMM for the SPSW is easy and leads to accurate response results.
The retrofitted SPSWs r/c building under study exhibits desirable transient and residual interstorey drift characteristics, as well as a substantial increase in base shear and energy dissipation capacity.As a general conclusion and essentially a final suggestion to be made, in the imminent or future revision of modern seismic retrofit codes [3,35], the option of utilizing SPSWs for seismic upgrading purposes of existing r/c buildings should be added.In this sense, both the FEM and OMM options for modeling SPSW can be proposed; nevertheless, the OMM option may be preferred because it represents the tension-field action of the SPSW better than the FEM option.Obviously, the final decision with respect to the configuration of the SPSW strongly depends on the r/c building to be retrofitted.

Figure 1 .
Figure 1.Elements of a typical SPSW for a 3-story.Figure 1. Elements of a typical SPSW for a 3-story.

Figure 1 .
Figure 1.Elements of a typical SPSW for a 3-story.Figure 1. Elements of a typical SPSW for a 3-story.

Figure 2 .
Figure 2. Layout of the r/c building: first (ground) floor (left); second and third floors (right).

Figure 3 .
Figure 3. Front view (left) and section (right) of the r/c building.

Figure 2 .
Figure 2. Layout of the r/c building: first (ground) floor (left); second and third floors (right).

Figure 2 .
Figure 2. Layout of the r/c building: first (ground) floor (left); second and third floors (right).

Figure 3 .
Figure 3. Front view (left) and section (right) of the r/c building.Figure 3. Front view (left) and section (right) of the r/c building.

Figure 3 .
Figure 3. Front view (left) and section (right) of the r/c building.Figure 3. Front view (left) and section (right) of the r/c building.

Figure 5 .
Figure 5. Model of the r/c building.

Figure 5 .
Figure 5. Model of the r/c building.

Figure 17 .
Figure 17.Plastic hinge formations-Orthotropic Membrane Model (OMM), t = 9.0 mm.The maximum Von Mises and normal (tensile and compressive) stresses are listed in Table15, whereas Figures18 and 19display the Von Mises stresses and principal tensile stresses, respectively, for the worst seismic motion "1b".From the results of Table15and in conjunction with Figures18 and 19, yielding of the web-plate of the SPSW is now achieved for three seismic motions, but the ultimate strength of 360 MPa is not exceeded.Therefore, the desired behavior of the retrofitted SPSWs r/c building is obtained for all seismic motions considered.

Table 2 .
Longitudinal reinforcement of columns.

Table 2 .
Longitudinal reinforcement of columns.

Table 6 .
Maximum Von Mises and shear stress to SPSWs.

Table 6 .
Maximum Von Mises and shear stress to SPSWs.

Table 8 .
Maximum Von Mises and shear stress to SPSWs.

Table 9 .
Plastic hinges at the columns of the 1st storey.

Table 10 .
Plastic hinges at the columns of the 2nd storey.

Table 13 .
Maximum Von Mises and principal stress to SPSWs, status of the SPSW.

Table 13 .
Maximum Von Mises and principal stress to SPSWs, status of the SPSW.

Table 14 .
Interstorey drift ratios and base shear forces.

Table 15 .
Maximum Von Mises and principal stress to SPSWs, status of the SPSW.

Table 15 .
Maximum Von Mises and principal stress to SPSWs, status of the SPSW.