Laboratory Study of Effective Stress Coefﬁcient for Saturated Claystone

: Claystone is potentially the main rock formation for the deep geological disposal of high-level radioactive nuclear waste. A major factor that affects the deformation of the host medium is effective stress. Therefore, studying the effective stress principle of claystone is essential for a stability analysis of waste disposal facilities. Consolidated drained (CD) tests were carried out on claystone samples to study their effective stress principle in this paper. Firstly, two samples were saturated under a speciﬁed conﬁning pressure and pore pressure for about one month. Secondly, the conﬁning pressure and pore pressure were increased to a speciﬁed value simultaneously and then reverted to the previous stress state (the deformations of the samples were recorded during the whole process). Different incremental combinations of the conﬁning pressure and pore pressure were tried at this step. Finally, the effective stress coefﬁcients of the samples were obtained through a back analysis. Furthermore, some potential inﬂuencing factors (the neutral stress and loading rate) of the effective stress coefﬁcient were also studied through additional tests. Some interesting results are worth mentioning: (1) the effective stress coefﬁcient of claystone is close to one; (2) the neutral stress and loading rate may have little effect on the effective stress coefﬁcient of claystone.


Introduction
As a potential host medium for the deep geological disposal of radioactive nuclear waste, claystone is found under highly complex hydro-mechanical (HM) conditions [1].Therefore, studying the stress-strain laws of claystone under HM conditions is essential for the stability analysis of radioactive waste disposal repositories.Because of its important role in the stress-strain laws of a geomaterial, the effective stress principle of claystone was studied in this paper.
Effective stress was first proposed by Terzaghi [2], who considered that pore pressure could counteract total stress.The effective stress principle satisfies the following form: where σ e is the effective stress, σ is the total stress, and σ p is the pore pressure.However, Biot [3] found that Terzaghi's effective stress principle was unsuitable for porous media with low permeability and believed that pore pressure could not offset the total pressure in a 1:1 ratio.A modified effective stress principle was proposed as follows [3]: The effective stress coefficients of a two-component porous medium are deduced based on the existing research work, and the phenomenon of Zoback and Byerlee [10] is explained based on this conclusion.
Tuncay and Corapcioglu [12] Saturated: ; η 1 is the effective stress coefficient for the fractures; η 2 is the effective stress coefficient for the pores; σ f p is the pore pressure in the fractures; σ p p is the pore pressure in the pores; α f is the volume fraction of the fractures; K s is the bulk moduli of grain; K f r is the drained bulk modulus of the fractured porous medium; K m f r is the drained bulk modulus of the nonfractured porous medium.
An effective stress principle for saturated fractured porous media is proposed based on the assumption of linear elasticity.
George and Barakat [13] Saturated: η = 0.71; A series of loading-unloading (both total stress and pore pressure) cycles applied by gas pressure were performed on the coal specimen, and the effective stress coefficient was obtained.
The effective stress coefficient of illite-rich shale was determined according to the transient pulse test results of saturated samples.
A theoretical relationship between the acoustic velocity and mean effective stress of the Nankai accretionary prism was calculated using DEM (Differential Effective Medium) theory and the aspect ratio spectrum of pore space, and Terzaghi's effective stress principle was introduced to analyze the pore pressure distribution of Nankai trough.
Bagherieh et al. [16] Unsaturated: ; u mw , u ma , u Mw , and u Ma are the micropore water, micropore air, macro pore water, and macro pore air pressures; α m and α M are the conventional effective stress coefficients of saturated double-porous media; S m(e) is the suction value separating saturated from unsaturated conditions in the micropores; S M(e) is the matric suction value separating saturated from unsaturated conditions in the macro pores; Ω is the material parameter.
Drying and one-dimensional consolidation tests are performed on initially saturated samples of the kaolin (double-porosity compacted soil) at different net stresses, and the test results were accurately predicted using the new effective stress principle.

Ghabezloo et al. [2]
Saturated: η = cσ d + d; c and d are the fitting parameters; σ d is the differential stress.
The effective stress law for the permeability of limestone is studied by drained hydrostatic compression and constant-head permeability tests, and the results show that the effective stress coefficient was linearly related to differential stress.

Nowamooz et al. [17]
Unsaturated: σ w is the pore water pressure; σ a is the pore air pressure; φ b is the angle indicating the increase in the matrix suction's shear stress function; φ is the lowest matrix suction.
The effective stress law of compacted natural clay sand in Missillac was obtained using the direct shear test and the soil water retention curve (SWRC), and its validity was verified by simulating the resilient behavior of repeated-load triaxial tests.
Konrad and Lebeau [18] Unsaturated: A Sr is the fraction of the fracture surface wetted by water; e * is the maximum local aperture currently occupied by water; B is the total perimeter of water menisci between two fracture walls; θ is the contact angle of the fracture water.
The effective stress equation is derived for partially saturated rough-walled fractures with any aperture distributions based on the capillary law, and the nonlinearity of the effective stress parameter versus the saturation degree curves is found to be mainly determined by the surface roughness (or the coefficient of variation) rather than the mean aperture of the fractures.
Zhang [19] Saturated: σA is the total normal force externally applied on the surface A; σ is A s is the total normal force acting on the solid-solid contact area, A s , with the local total stress σ is ; σ l A l is the total normal repulsive force acting in the water-film section, A l , between clay particles, with the local total pressure σ l ; σ p A p is the pressure σ p acting on the surface A p in the large pores occupied by free water.
The effective stress in a dense clay-water system is transferred through both the adsorbed interparticle porewater in narrow pores and the solid-solid contact between non-clay mineral grains.This concept has been widely validated by various kinds of experiments performed on the COX and OPA claystones.
Saurabh and Harpalani [20] Unsaturated: σ ij , ε ij and C ij are the total stress, compliance matrix, and strain along the i − j direction, respectively; η 1 and η 3 are the effective stress coefficients of transversely isotropic media; p is the pore pressure; p c is the pore pressure in the cleat system of media; s a m (p) is a pressure-dependent quantity coupling the sorption-based stress and strain in a microporous media.
The estimated values of the effective stress coefficients in both the vertical and horizontal directions are different, varying with pressure for methane depletion, and a conceptual physical model of effective stress, which considered absorption, was proposed.
A series of flow-through experiments consisting of three continuous stages (pre-reaction stage, reaction stage, and post-reaction stage) were conducted, and the cross-plot method was introduced to determine the effective law of tight sandstone with mineral dissoluble mineral.
Civan [22] Saturated: a and b are the fitting parameters; K is the intrinsic permeability of porous rock; φ is the porosity of porous formation.
The modified power-law equation yields a physically meaningful correlation because it successfully satisfies the low-end-and high-end-limit values of the effective stress coefficient and also provides a better quality match of the available experimental data than the semilogarithmic equation and the popular basic power-law equation.

Zhao et al. [23]
k n0 is the initial normal stiffness; u nmax is the maximum fracture closure.
A new effective stress coefficient model for single rough water-bearing fractures is proposed in terms of initial normal stiffness and maximum normal closure, and it was verified by laboratory and in situ experimental data.
The theoretical derivation and empirical formula are the two main expressions of the effective stress principle.The advantage of the theoretical derivation is that an equation that is more consistent with the physical principles can be obtained, but the disadvantage is that some physical quantities in the equation are difficult to measure.The accuracy of the empirical formula is related to the measured physical parameter (the permeability coefficient is favored), which is related to the effective stress coefficient.The adverse effects caused by water pressure changes (the permeability test requires a head difference between the upstream and downstream of the sample) in the permeability test are difficult to evaluate.In this study, the CD tests were conducted to measure the effective stress coefficient of claystone.The samples were firstly saturated under an in situ stress state for about one month.Then the effective stress coefficients were checked by changing the confining pressure and pore pressure in specific increments (the deformations of the samples were recorded during the whole process).Different increments of pore pressure and confining pressure were tried during the effective stress coefficient checking procedures, and an accurate conclusion was obtained through a back analysis (the effective stress coefficient was 0.991 for sample one and 0.995 for sample two).At last, some factors potentially influencing the effective stress principle of claystone were tested and discussed.

Experimental Device
The CD tests were performed on a parallel-linkage triaxial testing machine designed by the Institute of Rock and Soil Mechanics, Chinese Academy of Sciences.This machine can implement the mechanical tests simultaneously for two samples with the same confining pressures, the same pore pressures, and different axial pressures.The doublelinkage triaxial testing machine is shown in Figure 1a, and the schematic diagram of the increase/decrease in the specimen's confining, axial, and pore pressure is shown in Figure 1b.The deformations of the samples were measured by the LVDT (Linear Variable Differential Transformer), and the accuracy of the LVDT achieved was 10 −7 m.

Samples' Preparation and Basic Properties
The adequate claystone samples in this study were trimmed from blocks extracted at a depth of 223 m [24] (the effective stress is about 2.5 MPa).The detailed procedure of the sample preparation is illustrated in Figure 2 (the laboratory temperature is kept constant during the process of the sample preparation).Although we have tried our best to mini-

Samples' Preparation and Basic Properties
The adequate claystone samples in this study were trimmed from blocks extracted at a depth of 223 m [24] (the effective stress is about 2.5 MPa).The detailed procedure of the sample preparation is illustrated in Figure 2 (the laboratory temperature is kept constant during the process of the sample preparation).Although we have tried our best to minimize the impact on the sample during the sampling process, the possible impact of unloading (the sample is reduced from in situ stress to atmospheric pressure after coring) cannot be avoided.
Appl.Sci.2023, 13, x FOR PEER REVIEW 7 of 16 mize the impact on the sample during the sampling process, the possible impact of unloading (the sample is reduced from in situ stress to atmospheric pressure after coring) cannot be avoided.The initial physical characteristics of the samples were measured and displayed, as shown in Table 2.The claystone samples in this paper were relatively homogeneous (Figure 2b).Yu et al. [1] revealed the micro-structure and composition of the same claystone through scanning electron microscopic (SEM) tests and X-ray diffraction tests.In detail, the particles, most of which are clay mineral crystal particles with pores and are in contact from edge to face or face to face, are bending flaky structures [1].The main composition of them are shown in Table 3 [1].The initial physical characteristics of the samples were measured and displayed, as shown in Table 2.The claystone samples in this paper were relatively homogeneous (Figure 2b).Yu et al. [1] revealed the micro-structure and composition of the same claystone through scanning electron microscopic (SEM) tests and X-ray diffraction tests.In detail, the particles, most of which are clay mineral crystal particles with pores and are in contact from edge to face or face to face, are bending flaky structures [1].The main composition of them are shown in Table 3 [1].

Test Procedures
The experimental procedures are as follows: 1.
A confining pressure of 0.1 MPa was applied to establish the initial system stabilization (about 24 h). 2.
The confining pressure was increased to 2.5 MPa at a low rate of 1.68 kPa/min.The volume changes were monitored by a measuring system.3.
The water was thus injected into the samples from the top and bottom.Then, the pore pressure and confining pressure were simultaneously increased by 0.2 MPa at the rate of 1.68 kPa/min.4.
Simultaneous increases of both the confining pressure to 3.5 MPa and pore pressure to 1.0 MPa were applied.The loading rate was controlled at 0.2 kPa/min. 5.
Then Skempton's coefficient B was checked to determine the saturation degree of the samples by the following method: • Closing the drainage valve.

•
Measuring the increase in the corresponding pore pressure.

•
Decreasing the confining pressure down to 3.5 MPa and calculating Skempton's coefficient B.

•
Checking Skempton's coefficient B repeatedly until it was greater than 0.85.

6.
Keeping the drainage valve open, the effective stress coefficient of claystone was tested in line with the following steps: • Increasing the confining pressure by n MPa (n = 0, 0.1, 0.14, 0.16, 0.18, 0.2, 0.22), and the pore pressure by 0.2 MPa simultaneously.Then the confining pressure and pore pressure were restored to the previous state (σ c = 3.5 MPa, σ p = 1.0 MPa).

•
Observing and recording the deformation of samples.
In addition to the above test of the effective stress coefficient, this study also attempted to explore the influence of other potential factors (the neutral stresses and loading rate) on the effective stress coefficient.Different loading rates (0.01 kPa/s, 0.02 kPa/s, and 0.04 kPa/s) and a new pressure increment (∆σ c = ∆σ p = 0.5 MPa) were tried in the additional tests.
The variations of confining pressure and pore pressure are illustrated in Figure 3, and the controlled laboratory temperature is shown in Figure 4.

Test Procedures
The experimental procedures are as follows: 1.A confining pressure of 0.1 MPa was applied to establish the initial system stabilization (about 24 h). 2. The confining pressure was increased to 2.5 MPa at a low rate of 1.68 kPa/min.The volume changes were monitored by a measuring system.3. The water was thus injected into the samples from the top and bo om.Then, the pore pressure and confining pressure were simultaneously increased by 0.2 MPa at the rate of 1.68 kPa/min.4. Simultaneous increases of both the confining pressure to 3.5 MPa and pore pressure to 1.0 MPa were applied.The loading rate was controlled at 0.2 kPa/min. 5. Then Skempton's coefficient B was checked to determine the saturation degree of the samples by the following method: ).


Observing and recording the deformation of samples.
In addition to the above test of the effective stress coefficient, this study also attempted to explore the influence of other potential factors (the neutral stresses and loading rate) on the effective stress coefficient.Different loading rates (0.01 kPa/s, 0.02 kPa/s, and 0.04 kPa/s) and a new pressure increment ( = =0.5MPac p

   
) were tried in the additional tests.
The variations of confining pressure and pore pressure are illustrated in Figure 3, and the controlled laboratory temperature is shown in Figure 4.

Results
As shown in Figure 4, the experiments were divided into two stages: the saturation stage at the beginning and the stage of effective stress coefficient determination (the test stage).The following sections will detail the experimental results of each stage.

Results of the Saturation Stage
After the water was injected into the samples for about one month, Skempton's coefficient B was checked to determine the saturation degree.The results are shown in Table 4 and Figure 5.

Results
As shown in Figure 4, the experiments were divided into two stages: the saturation stage at the beginning and the stage of effective stress coefficient determination (the test stage).The following sections will detail the experimental results of each stage.

Results of the Saturation Stage
After the water was injected into the samples for about one month, Skempton's coefficient B was checked to determine the saturation degree.The results are shown in Table 4 and Figure 5.

Results
As shown in Figure 4, the experiments were divided into two stages: the saturation stage at the beginning and the stage of effective stress coefficient determination (the test stage).The following sections will detail the experimental results of each stage.

Results of the Saturation Stage
After the water was injected into the samples for about one month, Skempton's coefficient B was checked to determine the saturation degree.The results are shown in Table 4 and Figure 5.  Usually, Skempton's coefficient B is below one [25,26].Therefore, it was assumed that claystone was saturated as long as Skempton's coefficient B greater than 0.85.Therefore, sample one and sample two were considered to be saturated.It is worth mentioning the following: (1) the claystone studied in this paper can reach saturation in about 20 days [27]; (2) the saturation of the samples were determined after all the tests, and the results showed that the samples were saturated.

Results of the Test Stage
The test stage was also divided into two stages (Figure 3): the aim of Stage one was to determine the effective stress coefficient, and the aim of Stage two was to study the effect of the potential influencing factors (the neutral stress and loading rate) on the effective stress coefficient.

Results of Stage One
During Stage one, the pore pressure was always increased by 0.2 MPa at a rate of 0.01 kPa/s.However, different increments were tried for the confining pressure.Meanwhile, different increasing rates were used for the confining pressure to make the confining pressure and pore pressure reach their peak values simultaneously.The variations of the pressures and strains during Stage one are recorded in Figure 6 (negative values represent expansion, whereas positive values represent compression).Usually, Skempton's coefficient B is below one [25,26].Therefore, it was assumed that claystone was saturated as long as Skempton's coefficient B greater than 0.85.Therefore, sample one and sample two were considered to be saturated.It is worth mentioning the following: (1) the claystone studied in this paper can reach saturation in about 20 days [27]; (2) the saturation of the samples were determined after all the tests, and the results showed that the samples were saturated.

Results of the Test Stage
The test stage was also divided into two stages (Figure 3): the aim of Stage one was to determine the effective stress coefficient, and the aim of Stage two was to study the effect of the potential influencing factors (the neutral stress and loading rate) on the effective stress coefficient.

Results of Stage One
During Stage one, the pore pressure was always increased by 0.2 MPa at a rate of 0.01 kPa/s.However, different increments were tried for the confining pressure.Meanwhile, different increasing rates were used for the confining pressure to make the confining pressure and pore pressure reach their peak values simultaneously.The variations of the pressures and strains during Stage one are recorded in Figure 6 (negative values represent expansion, whereas positive values represent compression).It is well known that effective stress acts on the skeleton directly.When the effective stress changes, the skeleton will undergo corresponding deformation, which is manifested as when the effective stress decreases, the skeleton of the claystone will expand outwards, and the internal pores will be filled with more water; when the effective stress increases, the framework of the claystone will be compressed, and the pore water will be squeezed out.
An obvious law summarized by the test data is illustrated in Figure 6: (1) The samples undergo a significant expansion when the increment of pore pressure 0.2, 0.2, 0.2, 0.2, 0.2 MPa are equal; This means that the effective stress is constant under this confining and pore pressure condition.
-    It is well known that effective stress acts on the skeleton directly.When the effective stress changes, the skeleton will undergo corresponding deformation, which is manifested as when the effective stress decreases, the skeleton of the claystone will expand outwards, and the internal pores will be filled with more water; when the effective stress increases, the framework of the claystone will be compressed, and the pore water will be squeezed out.
An obvious law summarized by the test data is illustrated in Figure 6: (1) The samples undergo a significant expansion when the increment of pore pressure ∆σ p = 0.2, 0.2, 0.2, 0.2, 0.2 MPa is greater than the increment of confining pressure ∆σ c = 0, 0.1, 0.14, 0.16, 0.18 MPa; This means that the effective stress is reduced under this confining and pore pressure condition.(2) Conversely, when ∆σ p = 0.2 MPa is less than ∆σ c = 0.22 MPa, these samples are compressed; This means that the effective stress is increased under this confining and pore pressure condition.(3) The deformation of the samples are hardly observed when ∆σ p = 0.2 MPa and ∆σ c = 0.2 MPa are equal; This means that the effective stress is constant under this confining and pore pressure condition.

Results of Stage Two
At this stage, the increments of pore pressure and confining pressure were 0.5 MPa, and the loading/unloading rate was 0.01 kPa/s during the first cycle; the increments of pore pressure and confining pressure during the second and last cycles were the same as the first, but the loading/unloading rates were 0.02 kPa/s and 0.04 kPa/s, respectively.The variations in the pressures and strains during the whole of Stage two are recorded in Figure 7.

Results of Stage Two
At this stage, the increments of pore pressure and confining pressure were 0.5 MPa, and the loading/unloading rate was 0.01 kPa/s during the first cycle; the increments of pore pressure and confining pressure during the second and last cycles were the same as the first, but the loading/unloading rates were 0.02 kPa/s and 0.04 kPa/s, respectively.The variations in the pressures and strains during the whole of Stage two are recorded in The results showed the following: (1) There were slight fluctuations at the end of the loading and unloading.The reason for this phenomenon is that it was impossible to increase or decrease the pore pressure and confining pressure completely simultaneously.(2) The sudden ji er of the strain under stable stress conditions between the first and second cycles was due to a temperature fluctuation (Figure 4).(3) The deformations of the samples were all not obvious when the pore pressure and confining pressure were both increased or decreased by 0.5 MPa at a rate of 0.01 kPa/s, 0.02 kPa/s, and 0.04 kPa/s, because pore water could dissipate in time and no excess pore pressure would occur.The results showed the following: (1) There were slight fluctuations at the end of the loading and unloading.The reason for this phenomenon is that it was impossible to increase or decrease the pore pressure and confining pressure completely simultaneously.(2) The sudden jitter of the strain under stable stress conditions between the first and second cycles was due to a temperature fluctuation (Figure 4).(3) The deformations of the samples were all not obvious when the pore pressure and confining pressure were both increased or decreased by 0.5 MPa at a rate of 0.01 kPa/s, 0.02 kPa/s, and 0.04 kPa/s, because pore water could dissipate in time and no excess pore pressure would occur.

The Value of Effective Stress Coefficient for Claystone
The incremental form of Equation ( 2) can be written as follow: where ∆σ e is the increment of effective stress; ∆σ c is the increment of confining pressure; ∆σ p is the increment of pore pressure.
back analysis was performed to determine the effective stress coefficient.The FMINSEARCH function of MATLAB (version number: 8.3) was selected for the optimization calculation.The optimization calculation process is shown in Figure 8, and the objective function of the back analysis can be expressed as the following: To ensure the accuracy of this back analysis, the range of physical parameters is shown in Table 6.Table 6.The range of physical parameters before back analysis [28].The analysis results showed that the effective stress coefficient of claystone was 0.991 for sample one and 0.995 for sample two.

Start
The strains is calculated according to the stresses by equations ( 2) and ( 7) Input the measured stress-strain, initial value of inversion parameters and convergence accuracy of the optimization algorithm

Quantitative calculation difference between calculated and measured strains
The difference ≤ the convergence accuracy To ensure the accuracy of this back analysis, the range of physical parameters is shown in Table 6.Table 6.The range of physical parameters before back analysis [28].

Physical Parameters
E v /MPa V vh η Range 300-800 0.1-0.30.9-1.0 The analysis results showed that the effective stress coefficient of claystone was 0.991 for sample one and 0.995 for sample two.

Discussion on the Influencing Factors of Effective Stress Coefficient
The effective stress coefficient of claystone was probably related to the testing conditions.The results of Section 3.2.2showed that the deformations of the samples were not obvious when ∆σ c = ∆σ p = 0.5 MPa under different loading rates (0.01 kPa/s, 0.02 kPa/s, 0.04 kPa/s), indicating that the effective stress coefficient of claystone was still close to 1 even if different pressure increments and loading rates were taken.Therefore, the following conclusion can be drawn: (1) Whether the testing condition was ∆σ c = ∆σ p = 0.2 MPa or ∆σ c = ∆σ p = 0.5 MPa, the results were the same.It means that the neutral stresses may have little effect on the determination of the effective stress coefficient for claystone.(2) The results with different loading rates showed an inconspicuous deformation.We may conclude that as long as the loading rates are low enough so that the pore pressure can be dissipated time-efficiently, it will not affect the effective stress coefficient of claystone.

Conclusions
The effective stress principle of claystone was studied using the CD tests in this paper.

1.
Several loading-unloading cycles were conducted on the saturated claystone samples, and the deformation during this procedure was recorded.The results showed that both of the two samples were dilatant when the increments of pore pressure were greater than the increments of confining pressure; conversely, these samples were compressed when the increments of pore pressure were less than the increments of confining pressure; finally, the deformation of the sample was hardly observed when the increments of pore pressure and confining pressure were equal.The conclusion is that the effective stress coefficient of claystone is close to one.

2.
The relationship between effective stress and strain was analyzed to determine the effective stress coefficient of claystone.The results showed that the coefficient was 0.991 for sample one and 0.995 for sample two.

3.
The relationship between the effective stress coefficient of claystone and the potential influencing factors (the neutral stress and loading rate) were studied.The results show that the neutral stress and loading rate may have little effect on the effective stress coefficient of claystone.

6 .
Closing the drainage valve. Increasing confining pressure of 0.2 MPa. Measuring the increase in the corresponding pore pressure. Decreasing the confining pressure down to 3.5 MPa and calculating Skempton's coefficient B.  Checking Skempton's coefficient B repeatedly until it was greater than 0.85.Keeping the drainage valve open, the effective stress coefficient of claystone was tested in line with the following steps: the pore pressure by 0.2 MPa simultaneously.Then the confining pressure and pore pressure were restored to the previous state (

Figure 3 . 2 Figure 3 .
Figure 3.A detailed diagram of the test procedure.

Figure 4 .
Figure 4.The temperature of the pressure chamber.

Figure 4 .
Figure 4.The temperature of the pressure chamber.

Figure 4 .
Figure 4.The temperature of the pressure chamber.

Figure 5 .
Figure 5.The pressure curve during the saturation testing: (a) the pressure curve during the saturation; (b) testing the saturation for the first time; (c) testing the saturation for the second time.

Figure 6 .
Figure 6.The pressures and strains curve during Stage one: (a) sample one; (b) sample two.

;
This means that the effective stress is reduced under this confining and pore pressure condition.This means that the effective stress is increased under this confining and pore pressure condition.(3)The deformation of the samples are hardly observed when

Figure 6 .
Figure 6.The pressures and strains curve during Stage one: (a) sample one; (b) sample two.

Figure 7 .
Figure 7.The pressures and strains curve during Stage two: (a) sample one; (b) sample two.

Figure 7 .
Figure 7.The pressures and strains curve during Stage two: (a) sample one; (b) sample two.

Table 2 .
Initial condition for the tested samples.

Table 2 .
Initial condition for the tested samples.

Table 4 .
The Skempton's coefficient B for the samples.

Table 4 .
The Skempton's coefficient B for the samples.

Table 4 .
The Skempton's coefficient B for the samples.