Vibration Energy Harvester Based on Bilateral Periodic One-Dimensional Acoustic Black Hole

: An acoustic black hole (ABH) has been applied in the regulation of structural performance to form the aggregation effect of elastic waves in the local area of the structure, which has been used in energy harvesting in recent years. The piezoelectric vibration energy harvester (VEH) integrated with the beam of a bilateral periodic 1D ABH is proposed in this study. The theoretical model of the proposed VEH is established and analyzed based on the transfer matrix method. The performance of the VEHs is numerically simulated by COMSOL Multiphysics. The simulation results show that the performance of the bilateral ABH beam is higher than its traditional counterpart. Finally, the performance of the proposed VEH is validated in an experimental system. The experimental results show that the peak output voltage of the VEH Model 3 can reach 169.16 V, which is 1.9 times that of the traditional one. In the optimal impedance matching, the output power of the third bilateral VEH is 2.7 times that of the traditional ABH, which can reach 91.52 mW.


Introduction
Vibrations can be seen anywhere in industrial production and the surrounding circumstances, especially in structures such as beams or rods in civil engineering and mechanical engineering [1][2][3].This kind of redundant vibration is usually harmful and severely affects reliability and accuracy in various mechanical and precision equipment [4,5].However, the health status of the mechanical equipment and engineering structures can be monitored by wireless sensor network (WSN) nodes in real time.Traditional WSN [6] nodes are powered by batteries, which have a limited lifetime and are hard to maintain, especially in harsh environments and remote areas.Therefore, it is extremely important to develop a novel power supply method that can replace batteries with a long lifetime and is easy to maintain.
Harvesting energy from the vibrations in the surrounding environment where the WSN nodes are deployed, which can be converted to electrical energy, should be a possible solution.The device that can harvest vibration energy and convert it to electrical energy is a vibration energy harvester (VEH).VEHs can be divided into piezoelectric, electromagnetic and electrostatic types according to the operation principle.The piezoelectric VEH has wide employment through its simple structure and high electromechanical transfer coefficient [7].A cantilever is used as the primary structure of a traditional piezoelectric VEH with a narrow operation bandwidth and low harvesting efficiency.
The nonlinear effect can be used to improve the performance of traditional VEHs.Nonlinear structures are widely used due to their simple structure, which can be integrated into the cantilever beam in a VEH.As a nonlinear structure, the ABHs have wide employment in the field of vibrational reduction, noise reduction and energy harvesting due to the unique energy focus effect.ABHs have structures with geometrical or material parameters gradually decreasing t in thin-walled components such as beams and benches, which can focus the elastic wave [8].Gao et al. [9][10][11] proposed several kinds of one-dimensional double-leaf ABH beams with nested damping units, unit periodic arrays and spatial V-shaped bending.The low-frequency band gap and vibration characteristics of the structure were analyzed.The application of an ABH structure in energy harvesting has gained a lot of attention in recent years.Deng [12] uses the Lagrange equation to derive the combined equation of the bending vibration of the ABH beam with the piezoelectric layer.The influence of the parameters of the ABH and piezoelectric layer on energy harvesting efficiency is analyzed.Zhao et al. [13] established an electromechanical coupling model of an ABH cone structure with a surface-mounted piezoelectric transducer and analyzed the dynamic response with numerical simulation.Simulation results show that the response of the system is better than the traditional structure.Ji et al. [14] proposed an energy harvester integrated with a high-intensity ABH and validated it through experimental tests.
In addition, the characteristic that acoustic black holes can gather energy is also applicable to vibration suppression.Du et al. [15] proposed a new solution to embed 2D ABHs on the support plate to suppress the transmission of compressor vibration to the refrigerator body.Liang et al. [16] focus on the mid-and low-frequency performance of plates embedded with the array of an ABH for energy focalization and vibration and noise suppression.Lyu et al. [17] proposed a type of metamaterial plate enabling in-plane ultrawide vibration isolation in engineering equipment development and experiments show that the effective attenuation ability is compared with the traditional hexagonal lattice.
A piezoelectric VEH with a bilateral periodic 1D ABH is proposed in this paper.The vibration energy can be accumulated in the center of the ABH due to the focus effect and converted into electrical energy by the piezoelectric plates attached to the ABH surface.The theoretical model of the energy harvester with a bilateral periodic 1D ABH structure is established, and the performance of the above VEH is discussed through numerical simulation in COMSOL and verified by experimental tests.

VEH Integrated with Bilateral Periodic 1D ABH 2.1. Structure of VEH
The traditional VEH with an ABH is a cantilever beam with a unilateral ABH embedded.As shown in Figure 1, a VEH with a bilateral 1D ABH structure is proposed, where the piezoelectric plates attached to the ABH are ignored.Three different types of VEHs with an ABH are designed and analyzed.
Appl.Sci.2023, 13, 6423 2 of 18 parameters gradually decreasing t in thin-walled components such as beams and benches, which can focus the elastic wave [8].Gao et al. [9][10][11] proposed several kinds of one-dimensional double-leaf ABH beams with nested damping units, unit periodic arrays and spatial V-shaped bending.The low-frequency band gap and vibration characteristics of the structure were analyzed.The application of an ABH structure in energy harvesting has gained a lot of attention in recent years.Deng [12] uses the Lagrange equation to derive the combined equation of the bending vibration of the ABH beam with the piezoelectric layer.The influence of the parameters of the ABH and piezoelectric layer on energy harvesting efficiency is analyzed.Zhao et al. [13] established an electromechanical coupling model of an ABH cone structure with a surface-mounted piezoelectric transducer and analyzed the dynamic response with numerical simulation.Simulation results show that the response of the system is better than the traditional structure.Ji et al. [14] proposed an energy harvester integrated with a high-intensity ABH and validated it through experimental tests.
In addition, the characteristic that acoustic black holes can gather energy is also applicable to vibration suppression.Du et al. [15] proposed a new solution to embed 2D ABHs on the support plate to suppress the transmission of compressor vibration to the refrigerator body.Liang et al. [16] focus on the mid-and low-frequency performance of plates embedded with the array of an ABH for energy focalization and vibration and noise suppression.Lyu et al. [17] proposed a type of metamaterial plate enabling in-plane ultrawide vibration isolation in engineering equipment development and experiments show that the effective attenuation ability is compared with the traditional hexagonal lattice.
A piezoelectric VEH with a bilateral periodic 1D ABH is proposed in this paper.The vibration energy can be accumulated in the center of the ABH due to the focus effect and converted into electrical energy by the piezoelectric plates attached to the ABH surface.The theoretical model of the energy harvester with a bilateral periodic 1D ABH structure is established, and the performance of the above VEH is discussed through numerical simulation in COMSOL and verified by experimental tests.

Structure of VEH
The traditional VEH with an ABH is a cantilever beam with a unilateral ABH embedded.As shown in Figure 1, a VEH with a bilateral 1D ABH structure is proposed, where the piezoelectric plates attached to the ABH are ignored.Three different types of VEHs with an ABH are designed and analyzed.The collection of vibration energy is realized by the ABHs embedded in the cantilever of the VEH.The operation bandwidth can be adjusted by tuning the parameters of ABHs and the attached mass.The mass added to the edge of the beam greatly reduces the natural frequency of the VEH (The VEHs discussed next all contain mass blocks).

Operation Principle of VEH
As shown in Figure 2, the thickness of the ABH fits the formula h(x) = εx m , where h(x) and represents the thickness variation of the beam; ε is the undetermined coefficient and m is a power exponent.The structural stiffness is ensured by extending the ABH portion to a truncated platform at a minimum thickness, which is determined by the fabrication process.The operation principle of the proposed VEH is as follows: Vibration is generated in the cantilever beam when an external excitation signal is applied on the constrained end.The elastic waves according to the vibration are transmitted in the cantilever beam and concentrated in the center of the ABH zone due to the focus effect.The concentrated vibration energy is converted into electrical energy by the attached piezoelectric plate in the center of the ABHs.
Appl.Sci.2023, 13, 6423 3 of 18 The collection of vibration energy is realized by the ABHs embedded in the cantilever of the VEH.The operation bandwidth can be adjusted by tuning the parameters of ABHs and the attached mass.The mass added to the edge of the beam greatly reduces the natural frequency of the VEH.(The VEHs discussed next all contain mass blocks.)

Operation Principle of VEH
As shown in Figure 2, the thickness of the ABH fits the formula h(x) = εx m , where h(x) and represents the thickness variation of the beam; ε is the undetermined coefficient and m is a power exponent.The structural stiffness is ensured by extending the ABH portion to a truncated platform at a minimum thickness, which is determined by the fabrication process.The operation principle of the proposed VEH is as follows: Vibration is generated in the cantilever beam when an external excitation signal is applied on the constrained end.The elastic waves according to the vibration are transmitted in the cantilever beam and concentrated in the center of the ABH zone due to the focus effect.The concentrated vibration energy is converted into electrical energy by the attached piezoelectric plate in the center of the ABHs.

Dynamic Modeling of ABH Beam
As shown in Figure 3, the left side of the beam is fix constrained and the right side is left free.It is assumed that the external excitation 0 ( , ) sin Y x t Y Pt = is applied at 0.1 xL from the left end, where Y0 is the amplitude of the external excitation, and P is its frequency.The thickness of the constant thickness part of the beam is hm, xA is the length of a single ABH unit, ht is the truncated thickness of the ABH and xt is the truncated extended platform length.The adverse effects of the truncated platform can be offset to some extent by properly adding damping material to the surface of the curved portion of the ABH.xE is the length of the periodic joint in the middle and xL is the total length of the beam.The shear deformation of the cantilever beam is neglected because the length of the ABH beam is much larger than its thickness, and the transverse vibration is dominant in practice.The undamped transverse vibration equation of the beam based on the Euler-Bernoulli beam theory is [18]: where ρ is the material density of the ABH beam, ( ) T x is the cross-section area of the beam and ( , ) T M x t is the bending moment of the beam.

Dynamic Modeling of ABH Beam
As shown in Figure 3, the left side of the beam is fix constrained and the right side is left free.It is assumed that the external excitation Y(x, t) = Y 0 sin Pt is applied at 0.1 x L from the left end, where Y 0 is the amplitude of the external excitation, and P is its frequency.The thickness of the constant thickness part of the beam is h m , x A is the length of a single ABH unit, h t is the truncated thickness of the ABH and x t is the truncated extended platform length.The adverse effects of the truncated platform can be offset to some extent by properly adding damping material to the surface of the curved portion of the ABH.x E is the length of the periodic joint in the middle and x L is the total length of the beam.
Appl.Sci.2023, 13, 6423 3 of 18 The collection of vibration energy is realized by the ABHs embedded in the cantilever of the VEH.The operation bandwidth can be adjusted by tuning the parameters of ABHs and the attached mass.The mass added to the edge of the beam greatly reduces the natural frequency of the VEH.(The VEHs discussed next all contain mass blocks.)

Operation Principle of VEH
As shown in Figure 2, the thickness of the ABH fits the formula h(x) = εx m , where h(x) and represents the thickness variation of the beam; ε is the undetermined coefficient and m is a power exponent.The structural stiffness is ensured by extending the ABH portion to a truncated platform at a minimum thickness, which is determined by the fabrication process.The operation principle of the proposed VEH is as follows: Vibration is generated in the cantilever beam when an external excitation signal is applied on the constrained end.The elastic waves according to the vibration are transmitted in the cantilever beam and concentrated in the center of the ABH zone due to the focus effect.The concentrated vibration energy is converted into electrical energy by the attached piezoelectric plate in the center of the ABHs.

Dynamic Modeling of ABH Beam
As shown in Figure 3, the left side of the beam is fix constrained and the right side is left free.It is assumed that the external excitation from the left end, where Y0 is the amplitude of the external excitation, and P is its frequency.The thickness of the constant thickness part of the beam is hm, xA is the length of a single ABH unit, ht is the truncated thickness of the ABH and xt is the truncated extended platform length.The adverse effects of the truncated platform can be offset to some extent by properly adding damping material to the surface of the curved portion of the ABH.xE is the length of the periodic joint in the middle and xL is the total length of the beam.The shear deformation of the cantilever beam is neglected because the length of the ABH beam is much larger than its thickness, and the transverse vibration is dominant in practice.The undamped transverse vibration equation of the beam based on the Euler-Bernoulli beam theory is [18]: where ρ is the material density of the ABH beam, ( ) T x is the cross-section area of the beam and

( , )
T M x t is the bending moment of the beam.
The shear deformation of the cantilever beam is neglected because the length of the ABH beam is much larger than its thickness, and the transverse vibration is dominant in practice.The undamped transverse vibration equation of the beam based on the Euler-Bernoulli beam theory is [18]: where ρ is the material density of the ABH beam, T B (x) is the cross-section area of the beam and M T (x, t) is the bending moment of the beam.The ABH beam is a variable cross-section beam, which can be approximately equivalent to a linear combination of N equal cross-section beams as shown in Figure 4.When the N is large enough, the ABH beam can be approximated by the equivalent segmented beam, and then the vibration of the equivalent beam is analyzed by the transfer matrix method.The transfer matrix method is that any uniform beam in the segmented beam is analyzed separately to determine its corresponding transfer matrix, and then the whole beam is combined and analyzed according to the continuity between the segmented beams to obtain the whole vibration response of the ABH beam.
The ABH beam is a variable cross-section beam, which can be approximately equivalent to a linear combination of N equal cross-section beams as shown in Figure 4.When the N is large enough, the ABH beam can be approximated by the equivalent segmented beam, and then the vibration of the equivalent beam is analyzed by the transfer matrix method.The transfer matrix method is that any uniform beam in the segmented beam is analyzed separately to determine its corresponding transfer matrix, and then the whole beam is combined and analyzed according to the continuity between the segmented beams to obtain the whole vibration response of the ABH beam.For the single-section uniform beam after discretization, if the damping layer is neglected, the transverse free vibration equation of the number i uniform beam can be expressed as [19]: Let ( , ) w x t and ( , ) j x t be the components of the beam in the x-axis and z-axis directions, respectively, as shown in Figure 5.The shear and rotation of the beam are ignored since the thickness of the beam is much smaller than its length, where r and θ are the beam's axial strain and rotation angle after flexural deformation.Then, the length of the deformed element can be expressed as [20]: and the axial strain of the beam is: the axial strain of the beam can be neglected when the excitation of the ABH beam is mainly transverse vibration, which means r = 0.At this time, the following can be obtained: by substituting Equation ( 5) into Equation ( 6), the rotation angle θ can be expressed as: The Taylor expansion of Equation ( 7) can be obtained: Equal thickness region For the single-section uniform beam after discretization, if the damping layer is neglected, the transverse free vibration equation of the number i uniform beam can be expressed as [19]: Let w(x, t) and j(x, t) be the components of the beam in the x-axis and z-axis directions, respectively, as shown in Figure 5.The shear and rotation of the beam are ignored since the thickness of the beam is much smaller than its length, where r and θ are the beam's axial strain and rotation angle after flexural deformation.Then, the length of the deformed element can be expressed as [20]: and the axial strain of the beam is: the axial strain of the beam can be neglected when the excitation of the ABH beam is mainly transverse vibration, which means r = 0.At this time, the following can be obtained: by substituting Equation ( 5) into Equation ( 6), the rotation angle θ can be expressed as: The Taylor expansion of Equation ( 7) can be obtained: the curvature λ θ of the beam element after deformation can be expressed as: it can be obtained that the nonlinear strain ε B generated by the ABH beam during vibration is: Appl.Sci.2023, 13, 6423 6 of 18

Structure and Material
The response of the VEH with a bilateral 1D ABH is simulated and compared with a traditional VEH with a traditional 1D ABH.The cutting length of each ABH region is set to 90 mm for simplicity.The geometry parameters of these structures are listed in Table 1.The grid division in the FEM model of the ABH beam (take bilateral 1D ABH Model 1 as an example) is shown in Figure 6.As shown in Figure 7, the left end of the VEH is fixconstrained (the red arrow indicates the initial stress distribution under the external force at the free end), the right end is attached with a mass block and set free and the natural frequencies are acquired, as shown in  Without considering the damping layer, the bending moment of the uniform beam in the first section number i can be expressed as: where σ B is the inner stress of the ABH beam, b is the width of the ABH beam, substituting the stress-strain constitutive relation σ B = E B ε B and Equation (10) into Equation ( 11), the bending moment of the uniform beam number i can be expressed as: where E B is the elastic modulus of the beam, and I i (x) is the section moment of inertia of the number i uniform beam, which is expressed as: substituting Equation (12) into Equation ( 2), the vibration equation of the number i uniform beam is written as: The entire ABH beam is composed of multiple uniform beams after discretization, and the cross-section area and cross-section moment of the inertia of each uniform beam are different.The composite parameters of each node are introduced as follows: Appl.Sci.2023, 13, 6423 6 of 18 in summary, the transfer matrix method mechanical model of the ABH beam considering the nonlinear strain can be expressed as: (16)

Structure and Material
The response of the VEH with a bilateral 1D ABH is simulated and compared with a traditional VEH with a traditional 1D ABH.The cutting length of each ABH region is set to 90 mm for simplicity.The geometry parameters of these structures are listed in Table 1.The grid division in the FEM model of the ABH beam (take bilateral 1D ABH Model 1 as an example) is shown in Figure 6.As shown in Figure 7, the left end of the VEH is fix-constrained (the red arrow indicates the initial stress distribution under the external force at the free end), the right end is attached with a mass block and set free and the natural frequencies are acquired, as shown in Figure 8

Structure and Material
The response of the VEH with a bilateral 1D ABH is simulated and compared with a traditional VEH with a traditional 1D ABH.The cutting length of each ABH region is set to 90 mm for simplicity.The geometry parameters of these structures are listed in Table 1.The grid division in the FEM model of the ABH beam (take bilateral 1D ABH Model 1 as an example) is shown in Figure 6.As shown in Figure 7, the left end of the VEH is fixconstrained (the red arrow indicates the initial stress distribution under the external force at the free end), the right end is attached with a mass block and set free and the natural frequencies are acquired, as shown in Figure 8

Transient Response under Gaussian Pulse
The characteristic of a Gaussian pulse is energy concentration, which is beneficial to compress the signal spectrum and reduce the adjacent channel interference.The excitation in the actual environment can be better simulated by Gaussian pulses.The broadband Gaussian pulse is used as the excitation signal during the transient simulation of the VEH with ABHs.The formula of the broadband Gaussian pulse is as below: ( ) The Gaussian pulse has a wide frequency band and short excitation time, and its center frequency is set to 3000 Hz.Time domain and frequency domain images of Gaussian pulses are shown in Figures 9 and 10, respectively.In the simulation, a given displacement of 5 × 10 −5 m is loaded in the rightmost boundary of the beam to obtain an ideal excitation effect.The energy focus effect here of the ABH is reflected by the energy density of the ABH region, which can be validated by calculating the focused energy of the ABH zone.The Gaussian impulse response in the time domain is shown in Figure 11.Simulation results show that the energy focus effect of the ABH increased with the number of ABH arrays.

Transient Response under Gaussian Pulse
The characteristic of a Gaussian pulse is energy concentration, which is beneficial to compress the signal spectrum and reduce the adjacent channel interference.The excitation in the actual environment can be better simulated by Gaussian pulses.The broadband Gaussian pulse is used as the excitation signal during the transient simulation of the VEH with ABHs.The formula of the broadband Gaussian pulse is as below: The Gaussian pulse has a wide frequency band and short excitation time, and its center frequency is set to 3000 Hz.Time domain and frequency domain images of Gaussian pulses are shown in Figures 9 and 10, respectively.In the simulation, a given displacement of 5 × 10 −5 m is loaded in the rightmost boundary of the beam to obtain an ideal excitation effect.The energy focus effect here of the ABH is reflected by the energy density of the ABH region, which can be validated by calculating the focused energy of the ABH zone.The Gaussian impulse response in the time domain is shown in Figure 11.Simulation results show that the energy focus effect of the ABH increased with the number of ABH arrays.The response of the VEH with ABHs under Gaussian pulse is transformed by FFT, as shown in Figure 13.The VEH with more ABH periodic arrays can store more vibration energy in a wide frequency range of around 3000 Hz.The response of the VEH with ABHs under Gaussian pulse is transformed by FFT, as shown in Figure 13.The VEH with more ABH periodic arrays can store more vibration energy in a wide frequency range of around 3000 Hz.

Analysis in Frequency Domain
The analysis of these structures in a frequency domain is implemented under the condition that the rightmost end is applied with a 5 N force.The frequency band is divided into low frequency (0-2000 Hz), intermediate frequency (2000-4000 Hz) and high frequency (4000-6000 Hz).The response of the four VEHs with the ABH is compared with the velocity of the surfaces of the ABH central platform, as shown in Figure 14.Then, the root mean square (RMS) processing is performed on the simulation results, so the overall response of each structure in different frequency bands is observed, as shown in Figure 15.
As shown in Figure 14, the VEH with a bilateral ABH can obtain higher vibration energy mainly concentrated in the low-frequency range.Figure 15 shows that the RMS vibration velocity of the bilateral ABH structure is higher than the traditional counterpart, and the vibration velocity of Model 3 is about 3.84 times that of the traditional ABH in the low-frequency range.
into low frequency (0-2000 Hz), intermediate frequency (2000-4000 Hz) and high frequency (4000-6000 Hz).The response of the four VEHs with the ABH is compared with the velocity of the surfaces of the ABH central platform, as shown in Figure 14.Then, the root mean square (RMS) processing is performed on the simulation results, so the overall response of each structure in different frequency bands is observed, as shown in Figure 15.into low frequency (0-2000 Hz), intermediate frequency (2000-4000 Hz) and high frequency (4000-6000 Hz).The response of the four VEHs with the ABH is compared with the velocity of the surfaces of the ABH central platform, as shown in Figure 14.Then, the root mean square (RMS) processing is performed on the simulation results, so the overall response of each structure in different frequency bands is observed, as shown in Figure 15.

Experimental System
The performance of VEHs with ABHs is tested in an experimental system.The main components of the experimental platform are shown in Figure 16.
The working process of the whole experimental system is as follows: the signal generated by the signal generator will be amplified by the power amplifier to drive the vibrator to vibrate, and the electrical signal generated by VEH will be collected by the data recorder and transmitted to the host computer for display.
The prototype of four different models of VEHs is shown in Figure 17.These beams were fabricated by 3D printing and the piezoelectric plates with a size of 20 × 12 × 0.3 mm were pasted on the ABH part.The specific parameters of each structure are consistent with Table 1.
These beams are made of AlSi10Mg, the attached mass block is iron and the attached piezoelectric plate is made of PZT-5H with a 0.3 mm thickness truncated platform.The parameters of the material are listed in Table 2.
Appl.Sci.2023, 13, 6423 11 of 18 As shown in Figure 14, the VEH with a bilateral ABH can obtain higher vibration energy mainly concentrated in the low-frequency range.Figure 15 shows that the RMS vibration velocity of the bilateral ABH structure is higher than the traditional counterpart, and the vibration velocity of Model 3 is about 3.84 times that of the traditional ABH in the low-frequency range.

Experimental System
The performance of VEHs with ABHs is tested in an experimental system.The main components of the experimental platform are shown in Figure 16.The working process of the whole experimental system is as follows: the signal generated by the signal generator will be amplified by the power amplifier to drive the vibrator to vibrate, and the electrical signal generated by VEH will be collected by the data recorder and transmitted to the host computer for display.
The prototype of four different models of VEHs is shown in Figure 17.These beams were fabricated by 3D printing and the piezoelectric plates with a size of 20 × 12 × 0.3 mm were pasted on the ABH part.The specific parameters of each structure are consistent with Table 1.These beams are made of AlSi10Mg, the attached mass block is iron and the attached piezoelectric plate is made of PZT-5H with a 0.3 mm thickness truncated platform.The parameters of the material are listed in Table 2.A comparison of the experimental and simulated natural frequencies of the VEHs is shown in Table 3.The deviation between the simulation and experiment is mainly due to the insufficient precision of actual machining and the vibration interference of the vibrator itself cannot be completely eliminated.The second value of the natural frequency of each structure is used as the frequency of the external excitation, and the impedance matching is performed under the sinusoidal excitation with an amplitude of 3 N.The output voltage and power of VEHs with an ABH in the optimal impedance matching are shown in Figures 19 and 20.A comparison of the experimental and simulated natural frequencies of the VEHs is shown in Table 3.The deviation between the simulation and experiment is mainly due to the insufficient precision of actual machining and the vibration interference of the vibrator itself cannot be completely eliminated.The second value of the natural frequency of each structure is used as the frequency of the external excitation, and the impedance matching is performed under the sinusoidal excitation with an amplitude of 3 N.The output voltage and power of VEHs with an ABH in the optimal impedance matching are shown in Figures 19 and 20 The second value of the natural frequency of each structure is used as the frequency of the external excitation, and the impedance matching is performed under the sinusoidal excitation with an amplitude of 3 N.The output voltage and power of VEHs with an ABH in the optimal impedance matching are shown in Figures 19 and 20.The optimal impedance value of the traditional VEH with an ABH is 115 kΩ, the output peak voltage is 84.78 V and the output power reaches 33.63 mW.The optimal value of VEH Model 1 is 110 kΩ, the output peak voltage is 88.36 V and the output power reaches 35.62 mW.The optimal value of VEH Model 2 is 100 kΩ, the output peak voltage is 137.58V, and the output power reaches 75.01 mW.The optimal value of VEH Model 3 is 67 kΩ, the output peak voltage is 169.16V, and the output power is 91.52 mW.The peak output voltage of VEH Model 3 is 1.9 times that of the VEH with the traditional ABH, and the peak output power of VEH Model 3 is 2.7 times that of the VEH with a traditional ABH.The harvesting efficiency of the VEH with an ABH can be improved significantly with the number of ABH arrays.

Transient Voltage Response Test of VEH with ABH
Each VEH with an ABH is excited with a sinusoidal signal in its second natural frequency, which is connected with optimal impedance matching.The transient voltage response of each VEH is measured under sinusoidal excitation with an amplitude of 3 N.
Figure 21 shows the time domain response of the transient output voltage of VEHs at optimal impedance.The average output voltage of each VEHs is shown in Figure 22.The average output voltage increases with the number of ABH arrays.The optimal impedance value of the traditional VEH with an ABH is 115 kΩ, the output peak voltage is 84.78 V and the output power reaches 33.63 mW.The optimal value of VEH Model 1 is 110 kΩ, the output peak voltage is 88.36 V and the output power reaches 35.62 mW.The optimal value of VEH Model 2 is 100 kΩ, the output peak voltage is 137.58V, and the output power reaches 75.01 mW.The optimal value of VEH Model 3 is 67 kΩ, the output peak voltage is 169.16V, and the output power is 91.52 mW.The peak output voltage of VEH Model 3 is 1.9 times that of the VEH with the traditional ABH, and the peak output power of VEH Model 3 is 2.7 times that of the VEH with a traditional ABH.The harvesting efficiency of the VEH with an ABH can be improved significantly with the number of ABH arrays.

Transient Voltage Response Test of VEH with ABH
Each VEH with an ABH is excited with a sinusoidal signal in its second natural frequency, which is connected with optimal impedance matching.The transient voltage response of each VEH is measured under sinusoidal excitation with an amplitude of 3 N. the peak output power of VEH Model 3 is 2.7 times that of the VEH with a traditional ABH.The harvesting efficiency of the VEH with an ABH can be improved significantly with the number of ABH arrays.

Transient Voltage Response Test of VEH with ABH
Each VEH with an ABH is excited with a sinusoidal signal in its second natural frequency, which is connected with optimal impedance matching.The transient voltage response of each VEH is measured under sinusoidal excitation with an amplitude of 3 N.
Figure 21 shows the time domain response of the transient output voltage of VEHs at optimal impedance.The average output voltage of each VEHs is shown in Figure 22.The average output voltage increases with the number of ABH arrays.

Conclusions
A piezoelectric VEH with a bilateral periodic one-dimensional ABH is proposed in this paper.First, the energy focus effect of an ABH in the VEH is simulated by COMSOL under a Gaussian pulse excitation.The simulation results show that the beam with a bilateral ABH is easier to generate more energy with than the traditional one.The performance of the VEHs with an ABH is tested in an experiment.The experimental results show that the output voltage and power of the VEH with a bilateral periodic 1D ABH is higher compared with the VEH with a traditional one-dimensional ABH and increased with the number of ABH arrays.The main research results are as follows: (1) After the best impedance matching is completed: the output power of the traditional VEH reaches 33.63 mW, that of VEH Model The energy harvesting performance of VEH Model 3 is the best.The results show that the energy collection efficiency will increase with the increase in the ABH arrays.It is ex-

Conclusions
A piezoelectric VEH with a bilateral periodic one-dimensional ABH is proposed in this paper.First, the energy focus effect of an ABH in the VEH is simulated by COMSOL under a Gaussian pulse excitation.The simulation results show that the beam with a bilateral ABH is easier to generate more energy with than the traditional one.The performance of the VEHs with an ABH is tested in an experiment.The experimental results show that the output voltage and power of the VEH with a bilateral periodic 1D ABH is higher compared with the VEH with a traditional one-dimensional ABH and increased with the number of ABH arrays.The main research results are as follows:

Figure 5 .
Figure 5. Geometric relationship of the deformed element.

Figure 8 .
The natural frequency of the ABH beams decreases with the increment of the ABH arrays.The specific frequency values in the figure are shown in Table A1 in Appendix A.
. The natural frequency of the ABH beams decreases with the increment of the ABH arrays.The specific frequency values in the figure are shown in Table A1 in Appendix A.

Figure 5 .
Figure 5. Geometric relationship of the deformed element.
. The natural frequency of the ABH beams decreases with the increment of the ABH arrays.The specific frequency values in the figure are shown in Table A1 in Appendix A.

Figure 7 .
Figure 7. Simulation diagram of beam in COMSOL.

18 Figure 9 .
Figure 9. Normalized time domain for Gaussian pulse.Figure 9. Normalized time domain for Gaussian pulse.

Figure 9 .
Figure 9. Normalized time domain for Gaussian pulse.Figure 9. Normalized time domain for Gaussian pulse.

Figure 9 .
Figure 9. Normalized time domain for Gaussian pulse.

Figure 10 .
Figure 10.Normalized frequency domain for Gaussian pulse.

Figure 9 .
Figure 9. Normalized time domain for Gaussian pulse.

Figure 10 .
Figure 10.Normalized frequency domain for Gaussian pulse.

Figure 12 .
Figure 12.Kinetic energy density and strain of ABH Model 1: (a) ABH in 0.35 ms, (b) ABH in 0.5 ms, (c) ABH in 0.7 ms, (d) ABH in 0.9 ms.The response of the VEH with ABHs under Gaussian pulse is transformed by FFT, as shown in Figure13.The VEH with more ABH periodic arrays can store more vibration energy in a wide frequency range of around 3000 Hz.

Figure 14 .
Figure 14.The quadratic velocity of ABH region.

Figure 14 .
Figure 14.The quadratic velocity of ABH region.

Figure 16 .
Figure 16.Experimental system for energy harvesting performance.

Figure 18 .
Figure 18.Voltage frequency response of several beams.

Figure 18 .
Figure 18.Voltage frequency response of several beams.

Figure 20 .
Figure 20.Output power of VEHs with different load resistances.

Figure 21
Figure21shows the time domain response of the transient output voltage of VEHs at optimal impedance.The average output voltage of each VEHs is shown in Figure22.The average output voltage increases with the number of ABH arrays.

Figure 21 .
Figure 21.Transient output voltage of VEHs in optimal impedance.

Figure 22 .
Figure 22.Transient average output voltage of VEHs with optimal impedance.

Table 2 .
Parameters of size and material of energy harvester.

Table 2 .
Parameters of size and material of energy harvester.The output voltage of VEHs with an ABH in the frequency domain is shown in Figure 18, where the external load resistance is 10 kΩ.The peak output voltage of the VEH with a traditional ABH is 8.5 V at 153 Hz, and the peak output voltage of the VEH with the bilateral ABH Model 1 is 10.5 V at 146 Hz separately.The peak output voltage of the VEH with ABH Model 2 is 22.1 V at 140 Hz, and the peak output voltage of the VEH with ABH Model 3 is 29.2 V at 130 Hz.The peak output voltage of the VEH with the ABH increased with the number of ABH arrays.The peak output voltage of VEH Model 3 is 3.4 times that of the traditional counterpart.The specific natural frequency and output voltage are shown in Table A2 in Appendix A.

Table 3 .
Comparison of natural frequency.

Table 3 .
Comparison of natural frequency. .
1 can reach 35.62 mW, that of VEH Model 2 can reach 75.01 mW and that of VEH Model 3 can reach 91.52 mW.(2) Under the same external conditions: the output voltage of the traditional VEH reaches 84.78 V, that of VEH Model 1 can reach 88.36 V, that of VEH Model 2 can reach 137.58 V and that of VEH Model 3 can reach 169.16 V.

Table A1 .
First four-order natural frequency in simulation.

Table A1 .
First four-order natural frequency in simulation.

Table A1 .
First four-order natural frequency in simulation.

Table A2 .
First four-order natural frequency and output voltage in experiment.