Procedure for Improving the Energy, Environmental and Economic Sustainability of Transformation Houses

: A procedure for improving the energy, economic and environmental sustainability of the transformation houses in low-voltage distribution networks is described in this paper. This procedure is based on the reduction of the transformer consumption, copper and core losses. Likewise, the procedure distinguishes between transformation houses with old and new transformers. The reduction of core losses, replacing transformers with others of lower power or that are more efﬁcient, achieves signiﬁcant improvements in energy and environmental aspects. The reduction of copper losses, and applying reactive compensation techniques, such as harmonic ﬁltering and load balancing, applied in old and new transformation houses, have a greater impact on cost savings, especially when there are capacitive consumptions, as the Circular 3/2020 of the National Markets and Competition Commission of Spain determines. The procedure has been applied to an industrial transformation house, which has an old 1600 kVA transformer, resulting in signiﬁcant economic savings and CO 2 reductions of more than 60%, after replacing the current transformer with a more efﬁcient one.


Introduction
The transformers of the electrical distribution networks, used in industrial, commercial and residential activities, have significant energy consumptions and give rise to high carbon dioxide emissions into the atmosphere. Consequently, these machines affect the energy and environmental sustainability of electrical systems [1][2][3][4]. The energy consumption of transformers is due to their copper and core losses, as is well-known [5][6][7][8][9][10]. A report carried out in 2008 for the project "Strategies for development and diffusion of Energy Efficient Distribution Transformers (SEEDT)" [11] estimated the percentage of energy losses caused by distribution transformers is a third of the total losses in the electrical networks. That same report counted more than 4.5 million transformers in the distribution networks of the EU-27, with energy consumption-caused by losses-of 33.4 TWh/year, of which 24.1 TWh/year corresponded to core losses, and 9.3 TWh/year was due to copper losses. The saving potential estimated by the report reached 12 TWh/year and a reduction in CO 2 emissions of up to 4 million tons/year of CO 2 in the year 2025 [12] and was the most favorable scenario for a rapid replacement of existing transformers for more efficient ones, which had only 49% losses in the core than current transformers.
Aware of the importance of reducing the transformers' own consumptions, as a necessary step to promote the circular economy and guarantee energy and environmental 2 of 22 sustainability in the electricity sector, this paper describes a procedure to improve the sustainability of transformation houses in low-voltage distribution networks. This procedure is based on the reduction of transformer copper and core losses.
Actions to reduce copper losses were analyzed in a previous article [32]. These consist of minimizing the values of reactive, unbalanced and distortion currents, using well-known techniques, such as reactive power compensation and the use of harmonic filters. As a novelty, the minimization of unbalanced current is achieved using the active and reactive components of the unbalanced power vector ( → S uip , → S uiq ) [33]. These quantities provide sufficient information to network operators to obtain a more equitable distribution, in real-time, of the loads connected to the transformers. Copper loss reduction techniques are complementary to actions to reduce core losses and can be applied to both old, inefficient, transformers and efficient transformers.
The reduction of losses in the core is achieved in the procedure by replacing the old transformers with more efficient ones, of equal or lesser power. The use of efficient, lowerpower transformers considerably improves the energy sustainability of transformation centers, larger than the improvement derived from the reduction of copper losses.
The procedure for sustainability improvement has been applied to a transformation house of the low-voltage distribution network of an industrial estate, which has a 1600 kVA transformer, 25 years old, from the manufacturer Ormazabal. The study has focused on energy, environmental and economic aspects. For the energy study, a measurement campaign has been carried out, using the FLUKE 435 Series II network analyzer, whose loss calculator allows for the copper losses due to each component of the secondary currents to be measured separately. The environmental effects caused by copper and core losses, that is, the amount of emissions of carbon dioxide and other gases, have been determined using the emission factor from Spain (0.241 kg CO 2 /kWh), corresponding to the year 2019 [34], prior to which the measurement campaign was made. The economic effects have been obtained by applying Circular 3/2020 of the National Markets and Competition Commission of Spain [35]. The penalties for capacitive consumptions caused by two permanently connected capacitor banks Q c1 = 3 × 25 kVAr and Q c2 = 3 × 100 kVAr amount to tens of thousands of euros per year.
Finally, the energy, environmental and economic sustainability improvements resulting from the application of the procedure in the transformation house of the example are summarized in the conclusions.

Economic Costs of Transformer Losses and Charges for Capacitive Consumptions
Nowadays, the costs derived from energy losses in distribution transformers deserve special attention due to the high cost of energy. In Spain, these costs are obtained through the energy billing term [35], being: • FE = billed energy, in euros; • Te p = energy price in the hourly period p, expressed in EUR/kWh (Table 1), for the 6.1 TDA toll, where the transformation houses are included; • W p = energy lost by the transformer in the hourly period p, expressed in kWh; • i = the number of hourly periods of the transmission and distribution tolls.  Table 1 shows the strong increase in energy prices, especially during off-peak hours (up to 25 times), the result of which has been a reduction in the difference in prices between peak, flat and off-peak hours.
The energy is supplied in the transformation houses according to the 6.1 TDA toll, with voltage values between 1 and 30 kV, as shown in Table 2.
For the purposes of calculating energy costs, according to Equation (1), the prices of each hourly period in Table 1 must be applied to the supplies made at the times indicated in Table 3  Will not be penalized for capacitive consumptions outside these periods, even when the power factor is less than 0.98, or when the power factor in said periods is greater than 0.98.
The value of the power factor is obtained by the electrical companies, in each hourly period, as: where W p is the active energy (in kWh) and W q is the net reactive energy (in kVAr-h), calculated as the difference between the inductive and capacitive reactive energy supplies in the hourly period. The surcharge or penalty for capacitive reactive power supplies (RCAP) is calculated as [36]: being: the value of the net reactive energy supplies that exceed those corresponding to a power factor of 0.98 capacitive (0.20306 W p ). In other words, 20.306% of the capacitive reactive power supplies are not penalized.

Proposed Procedure for Improving Sustainability of Transformation Houses
Improving the sustainability of the transformation houses of the electrical distribution networks requires reducing the losses of the existing transformers in them. For this, the proposed methodology has two main steps ( Figure 1): (1) the reduction of copper losses, and (2) the reduction of core losses. Appl. Sci. 2022, 12, x FOR PEER REVIEW 4 of 22 Likewise, in order to ensure the quality of the electricity supply, Circular 3/2020, of the National Commission of Markets and Competition of Spain, January 15, establishes that the supplies made with the 6.1 toll: • Will be penalized for all capacitive consumptions supplied under power factors (PF) less than 0.98, between 0 and 8 h, on working days, and 24 h on holidays; • Will not be penalized for capacitive consumptions outside these periods, even when the power factor is less than 0.98, or when the power factor in said periods is greater than 0.98.
The value of the power factor is obtained by the electrical companies, in each hourly period, as: where is the active energy (in kWh) and is the net reactive energy (in kVAr-h), calculated as the difference between the inductive and capacitive reactive energy supplies in the hourly period.
The surcharge or penalty for capacitive reactive power supplies (RCAP) is calculated as [36]: being: the value of the net reactive energy supplies that exceed those corresponding to a power factor of 0.98 capacitive (0.20306 ). In other words, 20.306% of the capacitive reactive power supplies are not penalized.

Proposed Procedure for Improving Sustainability of Transformation Houses
Improving the sustainability of the transformation houses of the electrical distribution networks requires reducing the losses of the existing transformers in them. For this, the proposed methodology has two main steps ( Figure 1): (1) the reduction of copper losses, and (2) the reduction of core losses.

Reduction of Copper Losses
This consists of reducing the value of fundamental frequency currents, due to reactive power supplies and/or imbalances, as well as losses caused by non-fundamental frequency currents.
This step can be applied both in transformation houses with old (inefficient) and new (efficient) transformers.

Reduction of Copper Losses Caused by Reactive Currents
Losses caused by fundamental frequency reactive currents (P cr+ ) are usually the main copper losses of transformers in distribution networks and on which the managers of these electricity networks have the greatest savings. These losses can be calculated from the fundamental-frequency positive-sequence reactive powers Q + and line-to-neutral voltages, as follows: measured in the secondary of the transformer, and the short-circuit resistance of the transformers, and is obtained by: where V 20 is the RMS value of the secondary line-to-line no-load voltages, P cN is the rated copper power losses, determined according to IEC 60076-1 [37], and S N is the transformer rated power. Losses due to the reactive currents can be greatly reduced by using relatively inexpensive devices such as capacitor banks. In highly distorted electrical networks, capacitor banks can be replaced by harmonic filters, both active and passive, which are capable of jointly reducing load losses caused by reactive and distortion currents.
However, the use of non-variable compensation devices, both capacitor banks and passive filters, can be the cause of overcompensation, which usually increases the value of these losses in distribution transformers even above the existing values without reactive compensation devices. This case will be dealt with in more detail in the application case, in Section 4.

Reduction of Copper Losses Caused by Imbalanced Currents
Unbalances in the active power and reactive power supplies give rise to losses due to the load on the transformer, of value: where I − and I 0 are, respectively, the negative and zero sequence components of the transformer secondary currents and r cc is determined by (6). Currently, devices are known [38][39][40][41][42] for reducing unbalanced currents, which also have the ability to compensate for reactive power (Q + ) and, therefore, can additionally reduce the losses due to reactive currents (P cr+ ), defined by (5).
However, as indicated in Figure 1, the losses caused in the transformers due to unbalanced loads can be reduced, in industrial practice, by equitably distributing the active power and reactive power supplies between the secondary phases. To carry out this task, the managers of the electrical networks can use the representation of the angles (α p and α q ) of the following vector quantities [33]: The first one ( → S uip ) measures the effects of active power imbalances (P A , P B , P C ) supplied in each phase (z = A, B, C) of the transformer secondary, where a = 1 ∠ 120 • . The angles α p and α q can have values between 0 • and 360 • , and each phase of a three-phase system occupies a spatial sector of 120 • . Imbalances in phase A correspond to the values of the angles α p and α q between −60 • and 60 • . Imbalances in phase B give values of these angles between −60 • and −180 • and imbalances in phase C correspond to the values of α p and α q between 60 • and 180 • .
The ends of the segments represented in Figure 2a,  The angles and can have values between 0° and 360°, and each phase of a three-phase system occupies a spatial sector of 120°. Imbalances in phase A correspond to the values of the angles and between −60° and 60°. Imbalances in phase B give values of these angles between −60° and −180° and imbalances in phase C correspond to the values of and between 60° and 180°. The ends of the segments represented in Figure 2a

Reduction of Copper Losses Caused by Harmonic Currents
The losses due to the circulation of harmonic currents through the transformer windings are obtained by: where I hz are the RMS values of the harmonic currents in each phase of the transformers (z = A, B, C), n = f n / f 1 is the ratio between each harmonic frequency ( f n ) and the fundamental frequency ( f 1 = 50 ÷ 60 Hz) and r cc is the short-circuit resistance, determined according to (6).
The reduction of these losses can be done using passive or active harmonic filters. The use of passive filters is recommended, due to their cheaper cost-if the harmonic pollution is not too high. The elimination of harmonics of a very high value can be carried out by passive filters of the first order, tuned to the frequency ( f n ) of the harmonic to be eliminated. The series association of a coil, of inductance, and a capacitor, constitutes these passive filters, in which f 1 is the fundamental frequency, n = f n / f 1 , Q cn+ is the reactive power that the filter must compensate and V + is the effective value of the positive sequence voltage and fundamental frequency. Equation (10) is the resonance condition of a coil-capacitor series association at the tuning frequency f n , whereas that of Equation (11) follows from the reactive power (at the fundamental frequency) of the three coil-capacitor series associations of a three-phase passive filter.

Reduction of Core Losses
The second step of the proposed procedure is implemented in two ways: a In transformation houses with old, inefficient transformers, the reduction of core losses requires the replacement of these transformers with other efficient ones, of equal or less nominal power ( Figure 1); b In new transformation houses, in which efficient transformers have already been installed, the only option to reduce core losses is to replace them with other efficient transformers of lower nominal power, whenever possible ( Figure 1).
The replacement of transformers by others of lower power can be carried out when the transformer in operation in the transformation house works with very low load rates. Under these conditions, the losses in the core are always much greater than the losses in the copper and, therefore, the energy savings that result from reducing the former can be high.
The previously described actions for core loss reduction are based on the fact of these losses decrease with the rated power of the transformer. However, in the case of equally efficient transformers, the value of the short-circuit resistance (r cc ) evolves in the opposite direction, that is, it increases as the rated power decreases. For this reason, when a transformer is replaced by another of lower-rated power, the decrease in core losses must be weighed against the increase in copper losses in the new transformer.

Application Example
The procedure was applied to improve the energy, economic and environmental sustainability of one of the transformation houses of the low-voltage distribution network of an industrial area, in which there are furniture manufacturing, vehicle repair, industrial spare parts stores, as well as a couple of cafes/restaurants, among other companies. The transformation house has an operating transformer from the manufacturer ORMAZABAL, of 1600 kVA, whose primary is connected to the 20 kV medium voltage electrical network, with nominal features indicated in Table 4. Connected to the secondary of this transformer, there is a three-phase non-variable capacitor bank, with a power Q c1 = 3 × 25 kVAR. Likewise, after the first power measurements were made in the secondary of the transformer, the existence of a second three-phase non-variable capacitor bank was detected, with an estimated power Q c2 = 3 × 100 kVAR. This second reactive compensator was not visible, as it was outside the transformation house, inside the companies.
To carry out the study, a measurement campaign was made between the months of October and December of the year 2020, using the Fluke 435 Series II network analyzer. This instrument has a loss calculator for the distribution lines ( Figure 3), which can be adapted to measure the losses in transformers, introducing the value of the short-circuit resistance of the transformer instead of the resistance of the lines, and discounting the values of losses in the neutral conductor.

Application Example
The procedure was applied to improve the energy, economic and environmental sustainability of one of the transformation houses of the low-voltage distribution network of an industrial area, in which there are furniture manufacturing, vehicle repair, industrial spare parts stores, as well as a couple of cafes/restaurants, among other companies. The transformation house has an operating transformer from the manufacturer ORMAZA-BAL, of 1600 kVA, whose primary is connected to the 20 kV medium voltage electrical network, with nominal features indicated in Table 4.

Rated Power (kVA) Copper Losses (W)
Core losses (W) Short-Circuit Resistance (Ω) 1600 17,000 2600 0.011708 Connected to the secondary of this transformer, there is a three-phase non-variable capacitor bank, with a power = 3 × 25 kVAR. Likewise, after the first power measurements were made in the secondary of the transformer, the existence of a second threephase non-variable capacitor bank was detected, with an estimated power = 3 × 100 kVAR. This second reactive compensator was not visible, as it was outside the transformation house, inside the companies.
To carry out the study, a measurement campaign was made between the months of October and December of the year 2020, using the Fluke 435 Series II network analyzer. This instrument has a loss calculator for the distribution lines ( Figure 3), which can be adapted to measure the losses in transformers, introducing the value of the short-circuit resistance of the transformer instead of the resistance of the lines, and discounting the values of losses in the neutral conductor. The economic costs derived from the operation of the transformer and the surcharges for capacitive consumption have been obtained by applying Circular 3/2020, of the National Commission of Markets and Competition of Spain, 15 January

Energy Study of the Transformation House
The Fluke 435 Series II analyzer was connected to the transformer secondary terminals and measurements were made on working days and holidays. The values of the The economic costs derived from the operation of the transformer and the surcharges for capacitive consumption have been obtained by applying Circular 3/2020, of the National Commission of Markets and Competition of Spain, 15 January.

Energy Study of the Transformation House
The Fluke 435 Series II analyzer was connected to the transformer secondary terminals and measurements were made on working days and holidays. The values of the transformer copper losses, due to each component of the secondary currents, were measured by the Fluke 435 Series II analyzer, entering in the loss screen of this instrument (Figure 3) a value of resistance equal to the short-circuit resistance of the transformer, indicated in Table 4.
The active (P) and reactive (Q ) powers recorded throughout the measurement campaign on working days and holidays remained (without significant changes) at the values represented in Figures 4 and 5, for working days and holidays, respectively. ured by the Fluke 435 Series II analyzer, entering in the loss screen of this instrument ( Figure 3) a value of resistance equal to the short-circuit resistance of the transformer, indicated in Table 4.
The active ( ) and reactive ( ′) powers recorded throughout the measurement campaign on working days and holidays remained (without significant changes) at the values represented in Figures 4 and 5, for working days and holidays, respectively.      Based on the measured values of reactive power (Q ), represented in Figures 4 and 5, it was deduced that the capacitor banks (Q c1 and Q c2 ) were permanently connected at all hours of working days and holidays, giving rise to the high values of capacitive reactive power (higher than 300 kVAr) during times of low activity of companies. The values of the reactive power absorbed by the installations fed by the transformer, without the effect of the capacitor banks, are those represented by Q in Figures 4 and 5.
The values of the transformer copper losses, due to the active and reactive currents (P ca and P cr ), are those represented in Figures 6 and 7, for working days and holidays, respectively. Likewise, these figures represent the losses that the reactive currents would cause if the capacitor banks (P cr ) were not connected. The comparison of the values of P cr and P cr shows the impact produced by the capacitor banks on the copper losses of the transformer, which are especially important in periods of low activity of the companies. It can be noted in Figures 6 and 7 that transformer power losses caused by reactive currents have values between 500 and 700 W each hour in low activity periods, with capacitor banks, whereas these power losses reach only between 50 and 100 W each hour in these periods if capacitor banks were disconnected. transformer, which are especially important in periods of low activity of the comp It can be noted in Figures 6 and 7 that transformer power losses caused by reactiv rents have values between 500 and 700 W each hour in low activity periods, with cap banks, whereas these power losses reach only between 50 and 100 W each hour in periods if capacitor banks were disconnected.  Likewise, the Fluke 435 Series II analyzer recorded the values of copper losses ca in the transformer by unbalanced currents ( ) and distortion currents ( ). These v are those indicated in Figures 8 and 9, for working days and holidays, respectively. be seen in these figures that the copper losses caused by the distortions were greater those caused by the unbalances, undoubtedly due to the amplification of the disto currents produced by the Ferranti effect in the presence of capacitive loads. Howeve It can be noted in Figures 6 and 7 that transformer power losses caused by reactive rents have values between 500 and 700 W each hour in low activity periods, with capa banks, whereas these power losses reach only between 50 and 100 W each hour in t periods if capacitor banks were disconnected.  Likewise, the Fluke 435 Series II analyzer recorded the values of copper losses ca in the transformer by unbalanced currents ( ) and distortion currents ( ). These va are those indicated in Figures 8 and 9, for working days and holidays, respectively. I be seen in these figures that the copper losses caused by the distortions were greater those caused by the unbalances, undoubtedly due to the amplification of the disto currents produced by the Ferranti effect in the presence of capacitive loads. Howeve Likewise, the Fluke 435 Series II analyzer recorded the values of copper losses caused in the transformer by unbalanced currents (P cu ) and distortion currents (P ch ). These values are those indicated in Figures 8 and 9, for working days and holidays, respectively. It can be seen in these figures that the copper losses caused by the distortions were greater than those caused by the unbalances, undoubtedly due to the amplification of the distortion currents produced by the Ferranti effect in the presence of capacitive loads. However, the importance of losses due to imbalances and distortions is comparatively much less than those caused by capacitive reactive currents. importance of losses due to imbalances and distortions is comparatively much less than those caused by capacitive reactive currents.  From the values of the powers and losses in the copper measured in the secondary of the transformer, an inefficient operation of the same is observed, whose cause is, mainly, in the inadequate operation of the non-variable capacitor banks, used for the compensation of the reactive power. These devices are responsible for high values of capacitive reactive power in periods of low activity in companies (Figures 4 and 5). Consequently: (1) There are significant copper losses in the transformer, caused by the reactive compensation equipment, which give rise to significant CO2 emissions.
This fact can be seen in the energy losses on holidays in Table 5. The energy losses due to reactive currents on holidays amount to 1772.7 kWh/year. This value has been obtained by multiplying the losses caused by the reactive currents, each day (15.55 kWh, calculated based on the values in Figure 6), by 114 holidays in a one-year period, between September 2020 and August 2021. If the capacitor banks had not been connected, the reactive losses would have been only 113.92 kWh, on holidays (at a rate of only 0.9993  importance of losses due to imbalances and distortions is comparatively much less than those caused by capacitive reactive currents.  From the values of the powers and losses in the copper measured in the secondary of the transformer, an inefficient operation of the same is observed, whose cause is, mainly, in the inadequate operation of the non-variable capacitor banks, used for the compensation of the reactive power. These devices are responsible for high values of capacitive reactive power in periods of low activity in companies (Figures 4 and 5). Consequently: (1) There are significant copper losses in the transformer, caused by the reactive compensation equipment, which give rise to significant CO2 emissions.
This fact can be seen in the energy losses on holidays in Table 5. The energy losses due to reactive currents on holidays amount to 1772.7 kWh/year. This value has been obtained by multiplying the losses caused by the reactive currents, each day (15.55 kWh, calculated based on the values in Figure 6), by 114 holidays in a one-year period, between September 2020 and August 2021. If the capacitor banks had not been connected, the reactive losses would have been only 113.92 kWh, on holidays (at a rate of only 0.9993 From the values of the powers and losses in the copper measured in the secondary of the transformer, an inefficient operation of the same is observed, whose cause is, mainly, in the inadequate operation of the non-variable capacitor banks, used for the compensation of the reactive power. These devices are responsible for high values of capacitive reactive power in periods of low activity in companies (Figures 4 and 5). Consequently: (1) There are significant copper losses in the transformer, caused by the reactive compensation equipment, which give rise to significant CO 2 emissions.
This fact can be seen in the energy losses on holidays in Table 5. The energy losses due to reactive currents on holidays amount to 1772.7 kWh/year. This value has been obtained by multiplying the losses caused by the reactive currents, each day (15.55 kWh, calculated based on the values in Figure 6), by 114 holidays in a one-year period, between September 2020 and August 2021. If the capacitor banks had not been connected, the reactive losses would have been only 113.92 kWh, on holidays (at a rate of only 0.9993 kWh/day). Likewise, CO 2 emissions, on holidays, are 427.21 kg each year compared to only 27,454 kg/year that would be produced without the capacitor banks. The CO 2 emissions indicated in Table 5 have been determined based on the 0.241 kg CO 2 /kWh ratio, obtained from Red Eléctrica Española, in 2019 [34]. On the contrary, during the hours of greatest activity on working days, the capacitor banks work properly and achieve significant savings in losses and CO 2 emissions (Table 5).
(2) There are high economic penalties for capacitive reactive consumptions, after the Circular 3/2020 of the National Commission of Markets and Competition of Spain was introduced. (Table 6). In accordance with what is indicated in Section 2, not all the capacitive reactive energy (W q ), recorded each day in kVAr-h, is penalized, but only the net value (∆W q ) that results from discounting the inductive reactive energy in the penalty periods and indicated in Table 6, for working days and holidays. Penalties for the capacitive reactive energy (RCAP) have been calculated based on Equations (3) and (4), for a period of one year, between September 2020 and August 2021. This period includes 251 business days and 114 holidays.
(3) Copper losses and CO 2 emissions caused by unbalanced and distortion currents in the transformer windings are much lower than those due to reactive currents.
These energy losses have been obtained by adding the values of copper losses indicated in Figures 8 and 9, for each hour of the working days and holidays, and multiplying the resulting values by 251 working days and 114 holidays ( Table 7). The carbon dioxide emissions, indicated in Table 7, have been calculated by multiplying the energy losses by 0.241 kg CO 2 /kWh [34].

Energy and Environmental Effects Resulting from Improving the Sustainability of the Transformation House
The elimination of penalties for capacitive reactive energy, as well as a reduction in carbon dioxide emissions in the transformation center, can be carried out based on three actions, included in the procedure described in Section 3: (4) Optimization of the operation of the capacitor banks; (5) Reduction of copper losses caused by imbalances and distortions; (6) Replacing the transformer with a more efficient one, with less power.
The first of these actions is the one that can bring economic benefits, while the third provides, above all, energy and environmental benefits.

Optimization of the Operation of the Capacitor Banks
We have already indicated above that there are two banks of three-phase capacitors, fixed, connected to the secondary of the transformation center transformer. The first, Q c1 = 3 × 25 kVAR is located in the transformation center itself. The existence of the second bank of capacitors, Q c2 = 3 × 100 kVAR, was deduced after analyzing the registered powers.
The operation of the capacitor banks Q c1 and Q c2 is only efficient in the periods of greatest activity of the companies, in which the reactive power supplies are considerably reduced ( Figure 2) and the power factor of the transformer is close to 1 ( Figure 10). However, in periods of low activity, whether on working days or holidays, the capacitor banks supply large amounts of reactive power to the mains (Figures 4 and 5), with factors of capacitive power being very small, less than 0.3 capacitive (Figure 10). Appl. Sci. 2022, 12, x FOR PEER REVIEW 13 of 22

Energy and Environmental Effects Resulting from Improving the Sustainability of the Transformation House
The elimination of penalties for capacitive reactive energy, as well as a reduction in carbon dioxide emissions in the transformation center, can be carried out based on three actions, included in the procedure described in Section 3: (4) Optimization of the operation of the capacitor banks; (5) Reduction of copper losses caused by imbalances and distortions; (6) Replacing the transformer with a more efficient one, with less power.
The first of these actions is the one that can bring economic benefits, while the third provides, above all, energy and environmental benefits.

Optimization of the Operation of the Capacitor Banks
We have already indicated above that there are two banks of three-phase capacitors, fixed, connected to the secondary of the transformation center transformer. The first, = 3 × 25 kVAR is located in the transformation center itself. The existence of the second bank of capacitors, = 3 × 100 kVAR, was deduced after analyzing the registered powers. The operation of the capacitor banks and is only efficient in the periods of greatest activity of the companies, in which the reactive power supplies are considerably reduced ( Figure 2) and the power factor of the transformer is close to 1 ( Figure 10). However, in periods of low activity, whether on working days or holidays, the capacitor banks supply large amounts of reactive power to the mains (Figures 4 and 5), with factors of capacitive power being very small, less than 0.3 capacitive (Figure 10). The environmental and economic consequences of reactive power in the inefficient operation of the transformer are observed in Tables 5 and 6, respectively. To reduce their impact, it is necessary to optimize the operation of the capacitor banks. For this, it is proposed: a. Maintain the operation of the first capacitor bank (Q c1 ), without disconnection, at any time of the day, every day of the year, both working days and holidays; b. Connect the second capacitor bank (Q c2 ) only between 7:00 a.m. and 8:00 p.m. on working days, keeping it disconnected for the rest of the hours on working days and all hours on holidays. This solution can be applied, in a very economical way, by incorporating a switch with a programmable timer in this capacitor bank.
The energy effects of the limitation of the period of operation of the capacitor bank Q c2 are: (1) A significant decrease in the reactive power supplied, with very short capacitive periods, which are compensated by the inductive periods on working days and holidays (Figure 11), reaching power factors very close to unity ( (1) A significant decrease in the reactive power supplied, with very short capacitive periods, which are compensated by the inductive periods on working days and holidays (Figure 11), reaching power factors very close to unity (Table 8); Figure 11. Transformer reactive powers, in kVAR, after applying actions for optimizing the operation of capacitor bank : (a) working days, and (b) holidays. (2) The high reduction of transformer copper losses caused by reactive currents, especially on holidays (Figure 12), which, compared to those indicated in Table 5, represent energy savings of 2820 kWh/year and 679.58 kg/year, in CO2 emissions (Table 9).   (2) The high reduction of transformer copper losses caused by reactive currents, especially on holidays (Figure 12), which, compared to those indicated in Table 5, represent energy savings of 2820 kWh/year and 679.58 kg/year, in CO 2 emissions (Table 9). (1) A significant decrease in the reactive power supplied, with very short capacitive periods, which are compensated by the inductive periods on working days and holidays (Figure 11), reaching power factors very close to unity (Table 8); Figure 11. Transformer reactive powers, in kVAR, after applying actions for optimizing the operation of capacitor bank : (a) working days, and (b) holidays. (2) The high reduction of transformer copper losses caused by reactive currents, especially on holidays (Figure 12), which, compared to those indicated in Table 5, represent energy savings of 2820 kWh/year and 679.58 kg/year, in CO2 emissions (Table 9).

Reduction of Transformer Copper Losses Caused by Imbalance and Distortion Currents
The losses caused by current imbalances in the transformer are not affected by the operation of the capacitor banks, since these are balanced loads. Likewise, the values of these losses are very small, both working days and holidays (Figures 8 and 9). This is an indication that the loads are slightly unbalanced and, therefore, it will not be necessary to apply any specific action to reduce these losses, whose values will remain at those indicated in Table 7.
Regarding the phenomenon of distortion, the optimization of the operation of the capacitor banks has an additional beneficial effect, reducing the distortion currents and copper losses.
Indeed, the distortion of the currents is fundamentally caused by the amplifying effect caused by the capacitive loads. This fact is observed in Figure 13. During periods of low activity of the companies, in which there are high supplies of capacitive reactive power, the currents are highly distorted (Figure 13a), with THD% of 14.58%, while in the times of high activity of the companies, the currents are slightly distorted (Figure 13b), with THD% lower than 3.74%. Under these latter conditions, distortion copper losses have an average value of 5.5 W (Figure 8). In our opinion, this is the maximum value of the losses caused by the distortion of the loads, without the amplifying effect of the capacitors, in periods of low activity for the companies.

Reduction of Transformer Copper Losses Caused by Imbalance and Distortion Currents
The losses caused by current imbalances in the transformer are not affected by the operation of the capacitor banks, since these are balanced loads. Likewise, the values of these losses are very small, both working days and holidays (Figures 8 and 9). This is an indication that the loads are slightly unbalanced and, therefore, it will not be necessary to apply any specific action to reduce these losses, whose values will remain at those indicated in Table 7.
Regarding the phenomenon of distortion, the optimization of the operation of the capacitor banks has an additional beneficial effect, reducing the distortion currents and copper losses.
Indeed, the distortion of the currents is fundamentally caused by the amplifying effect caused by the capacitive loads. This fact is observed in Figure 13. During periods of low activity of the companies, in which there are high supplies of capacitive reactive power, the currents are highly distorted (Figure 13a), with THD% of 14.58%, while in the times of high activity of the companies, the currents are slightly distorted (Figure 13b), with THD% lower than 3.74%. Under these latter conditions, distortion copper losses have an average value of 5.5 W (Figure 8). In our opinion, this is the maximum value of the losses caused by the distortion of the loads, without the amplifying effect of the capacitors, in periods of low activity for the companies.
Consequently, the disconnection of the capacitor bank 2 , in the periods of low activity of the companies, gives rise to an additional reduction of the distortion currents and the losses caused by them. Considering that the value of losses due to distortion, without the effect of the capacitors, is the previously indicated 5.5 W every hour, it results in a 50% decrease in energy losses due to distortion currents, indicated in Table 7, for working days, and 75% for holidays. These reductions also extend, with the same percentage, to carbon dioxide emissions (Table 10). These important benefits make the additional installation of harmonic filters unnecessary, in our opinion.  Consequently, the disconnection of the capacitor bank Q c2 , in the periods of low activity of the companies, gives rise to an additional reduction of the distortion currents and the losses caused by them. Considering that the value of losses due to distortion, without the effect of the capacitors, is the previously indicated 5.5 W every hour, it results in a 50% decrease in energy losses due to distortion currents, indicated in Table 7, for working days, and 75% for holidays. These reductions also extend, with the same percentage, to carbon dioxide emissions (Table 10). These important benefits make the additional installation of harmonic filters unnecessary, in our opinion. The nominal values of the copper and core losses of efficient distribution transformers are indicated in Table 11. It is observed that the core losses of the transformers are smaller in the transformers of lower nominal power. This fact could justify the replacement of transformers with others of lower-rated power. However, it can also be seen in Table 11 that the short-circuit resistance (r cc ) evolves in the opposite direction, so the load losses will increase if lower-power transformers are used, since the currents maintain their value. For this reason, in the event of replacing the actual transformer with another of lower power, the most suitable replacement transformer must be the one whose total losses, obtained as the sum of the copper losses and the core losses, have the lowest value.
c ), is obtained as the sum of the losses due to the active currents (W ca ), to the reactive currents (W cr , Table 9), to the unbalanced currents (W cu , Table 7) and the distortion currents (W ch , Table 10), determined after the optimization of the operation of the capacitors, i.e.: The copper losses for efficient transformers (W c ) have been calculated based on the following expression: where r cc is the short-circuit resistance of the 1600 kVA Ormazabal transformer (Table 4) and r cc is the short-circuit resistance of the analyzed efficient transformers (Table 11). The total losses of each transformer have been obtained by adding their copper losses c or W c ) to the core losses of each transformer (Tables 4 and 11).
The values of carbon dioxide emissions (Table 13) have been determined by multiplying the total energy lost for each transformation and operation of the capacitor banks, indicated in Table 12, by the emissions factor for the year 2019, in Spain, 0.241 kg CO 2 /kWh. Observing the total energy losses, indicated in Table 12, and the carbon dioxide emissions, in Table 13, it follows that the most suitable replacement transformer for the actual 1600 kVA must be an efficient transformer with a nominal power of 1000 kVA, since it is the one with the lowest total losses (Table 12) and carbon dioxide emissions (Table 13). Compared with the 1600 kVA inefficient transformer, annual energy savings of 19,037.95 kWh and annual savings in carbon dioxide emissions of 4588.14 kg are obtained.

Economic Effects of Improving the Sustainability of the Transformation House
The economic costs derived from the operation of each transformer are obtained by multiplying the value of its total energy losses (in the copper and in the core), for each hourly period (P1, P2, P3, P4, P5 and P6) and type of day (A, B, B1, C and D), according to Table 3, by the energy prices in each hourly period ( Table 1). The effects of the increase in electricity prices from January 2020 to January 2022 have been considered in the study.
The results indicated in Table 14 show that improving the sustainability of the transformation house, optimizing the operation of the capacitor bank Q c2 and replacing the inefficient 1600 kVA transformer with an efficient 1000 kVA transformer, allows savings of 158.76 EUR/year, at 2020 energy prices. However, at energy prices of the beginning of the year 2022, these savings amount to the sum of 1536.75 EUR/year. The savings that would have been obtained without the replacement of the inefficient transformer, of 1600 kVA, reducing only its copper losses, would only be 13.53 EUR/year, at 2020 prices, and 206 EUR/year, at prices of principles of the year 2022. To the previous savings, in economic costs of the losses in the transformer, it would be necessary to add the savings in penalties for capacitive reactive energy, which amount to 44,158.83 EUR/year (Table 6), after the optimization of the operation of the bank of capacitors Q c2 .

Summary of Benefits derived from the Improvement of the Sustainability of the Transformation House
The application of the procedure for improving the sustainability of the transformation center used in the application example has allowed the energy, environmental and economic savings indicated in Table 15 to be achieved. Table 15. Summary of energy, emissions and economic savings in the industrial transformation center: (1) Optimizing only the operation of the capacitor banks and (2) replacing the inefficient transformer with an efficient one, with optimization of the capacitors. Reducing only the copper losses, without replacing the transformer with a more efficient one, by optimizing the operation of the capacitor bank Q c2 , the benefits obtained are as follows ( In addition, if an efficient 1000 kVA transformer replaces the inefficient 1600 kVA transformer, the benefits derived from the full application of the procedure to improve the sustainability of the transformation house are as follows (

Conclusions
In this paper, the economic, energy and environmental effects resulting from applying the proposed procedure to improve the sustainability of the transformation houses of the low-voltage distribution networks have been analyzed.
Reducing reactive currents, either through the use of suitable compensation devices or by optimizing the operation of existing ones, is usually a technique that achieves a greater reduction of copper losses in distribution transformers, greater than imbalance compensation and harmonic filtering.
However, the energy savings and reduced CO 2 emissions resulting from minimizing copper losses in older inefficient transformers are very small compared to the savings that can be achieved by reducing core losses, after replacing those transformers with other efficient ones. The combined utilization of current reduction techniques (copper losses) and the use of efficient transformers (core losses) in transformation houses allow for savings of between 55% and 70% in energy consumption and CO 2 emissions in transformation houses with old transformers. However, only between 10% and 20% of these savings are due to the application of copper loss reduction techniques.
The decrease in economic costs, resulting from the application of the proposed procedure to improve the sustainability of transformation houses, is more modest than its energy and environmental effects, especially if only actions are applied to reduce copper losses, such as can be seen in Table 15. However, the current energy shortage means that these cost savings can reach interesting amounts. The savings in penalties for capacitive consumptions are insignificant if the reactive compensators have been well chosen. Otherwise, optimizing the operation of the reactive compensation devices allows significant savings to be achieved through penalties, as seen in the application example (Table 15).
The results in reducing CO 2 emissions and economic savings obtained in this paper can be extended to each country, simply by using the CO 2 emission factor and the energy prices of the corresponding country.
The procedure described in this paper is being applied to the monitoring of the transformation houses of the distribution network of a small city in collaboration with the electricity company Eléctrica de Vinalesa S.L.U. It is expected that the development of this project will lead to new lines of research that we will describe in future papers.

Conflicts of Interest:
The authors declare no conflict of interest. The funders had no role in the design of the study; in the collection, analyses, or interpretation of data; in the writing of the manuscript; or in the decision to publish the results.  ( 1 ) actual operation of capacitor banks in the transformation house Superscript ( 2 ) optimized operation of capacitor banks Superscript ( 3 ) optimized operation of capacitor banks and changing actual transformers by efficient ones Superscript ( 4 ) number of working days in the annual period analyzed Superscript ( 5 ) number of holidays in the annual period analyzed Superscript ( 6 ) costs, in euros, calculated according to 2020 energy prices Superscript ( 7 ) costs, in euros, calculated according to 2022 energy prices