Development and Evaluation of the Traction Characteristics of a Crawler EOD Robot

: Today, terrestrial robots are used in a multitude of ﬁelds and for performing multiple missions. This paper introduces the novel development of a family of crawling terrestrial robots capable of changing very quickly depending on the missions they have to perform. The principle of novelty is the use of a load-bearing platform consisting of two independent propulsion systems. The operational platform, which handles the actual mission, is attached (plug and play) between the two crawler propulsion systems. The source of inspiration is the fact that there are a multitude of intervention robots in emergency situations, each independent of the other. In addition to these costs, there are also problems with the specialization of a very large number of staff. The present study focused on the realization of a simpliﬁed, modular model of the kinematics and dynamics of the crawler robot, so that it can be easily integrated, by adding or removing the calculation modules, into the software used. The designed model was integrated on a company controller, which allowed us to compare the results obtained by simulation with those obtained experimentally. We appreciate that the analyzed Explosive Ordnance Disposal (EOD) robot solution represents a premise for the development of a family of EOD robots that use the same carrier platform and to which a multitude of operational platforms should be attached, depending on the missions to be performed.


Introduction
The most serious threat to the civilized world, following nuclear threats, is terrorist threats [1]. In recent decades, due to the expansion of civilization across the globe, and the ease of access to information, technology and culture, extremist actions and reactions have proliferated [2]. They are symmetrical with extremism in the process of globalization and aim to stop and destabilize the offensive growth of the civilized world against increased fragmentation, promiscuity, poverty and violence [3].
Terrorism does not have a generally accepted definition. The difficulty of defining it stems both from its complexity and from a wide divergence of positions of individuals, organizations or states involved in the fight against terrorism [4]. The simplest definition is "purpose and method": Terrorism is an unconventional fighting tactic used to achieve strictly political goals that are based on acts of violence, sabotage or threat, executed against a state, organizations, social groups or against a group of civilians, with the precise purpose of producing a generalized psychological effect of fear and intimidation [5]. The ultimate goal is to put pressure on that entity to get it to act in accordance with the wishes of the terrorists if that goal cannot be achieved by conventional means [6].
The correct and complete definition and understanding of the phenomenon of terrorism are absolutely necessary for the elaboration of effective strategies and tactics in environment; Natural language [22]: natural language changes quite frequently, so simple word recognition is no longer enough to understand the real meaning of a processed text; Learning [23]: ideally, a robot could learn the tasks it has to perform by simply repeating similar actions performed by a human operator; Planning and problem solving [24]: intelligence is inherently associated with the ability to plan actions needed to achieve a particular goal, as well as the ability to solve problems that arise when these action plans do not work; Inference [25]: by inference, it is possible to fill in the missing information to solve a certain problem; Search [26]: in terms of artificial intelligence, search means the efficient examination of a representation of knowledge, specific to a certain problem (search in a "space") in order to determine a solution; Vision [27]: by creating artificial vision systems, the actions of the mobile robot can be made more precise and complex. Sometimes, mobile robots appear in the form of vehicles capable of operating autonomously on the ground (UGVs-Unmanned Ground Vehicles), in the air (UAVs-Unmanned Aerial Vehicles) or in the water (UUVs-Unmanned Undersea Vehicles). In the broadest sense of the definition, a mobile robot is a real-time integrated system (embedded real-time system), that has sensors [28] for environmental perception, execution elements for performing actions on the environment and a control system for mapping perception in action [29]. Perception and action are the major aspects that define a mobile robot. Depending on the organization of these three functional aspects, it can be considered that the mobile robot has a greater or lesser degree of autonomy.
The best-known type of mobile robot is the Automated Guided Vehicle (AGV-Automated Guided Vehicle). AGVs operate in pre-programmed environments and are inflexible and "fragile" in operation; thus, any unforeseen route changes (objects on the runway) can lead to a compromise of the entire mission [30].
The alternative to AGV is to build mobile robots with autonomy in motion to travel in the environment to perform various tasks; adapt to changes in the environment; learn from experience and change their behavior accordingly (how to act); build internal representations of the world around them that can be used for decision-making processes (for example, for navigation).

The Functions of a Crawler Mobile Robot
From a functional point of view, a mobile robot consists of three modules: the role of the sensor module is to estimate the speed and position of the mobile robot [32][33][34]; the orientation module is the reference generator for the orientation of the mobile robot in space [33]; the control module is the subsystem that generates the control quantities for the execution elements based on the data provided by the orientation module [34].
The following essential functions of a mobile robot can be defined according to the functional modules: A. Navigation function [35]: workspace representation; avoidance of obstacles; location function; motion planning; motion control. B. Task Planning Function [36]: C. Interaction and communication function [37].

Justification for the Use of a Crawler Mobile Robot for EOD Actions
Anti-terrorism intervention requires the use of robots to limit risks for the following reasons: performing procedures during IED intervention missions, which include observation and inspection, X-ray analysis, disruption, etc.; no matter how careful the operator is in responding to the IED, there is always the possibility that the attacker may be nearby so that he can operate the explosion-proof device remotely; even if a robot cannot neutralize an IED, it can still be used to provide information on the choice of procedure and devices needed to evacuate/eliminate the dangerous object from the threatened area.

Features of Crawler Mobile Robots
Named mobile robots and controlled/autonomous vehicles, robot trailers or robotics, have a structure consisting of ( Figure 2): From a functional point of view, a mobile robot consists of three m the sensor module is to estimate the speed and position of the mobile orientation module is the reference generator for the orientation of th space [33]; the control module is the subsystem that generates the con the execution elements based on the data provided by the orientation m The following essential functions of a mobile robot can be defined functional modules: A. Navigation function [35]: workspace representation; avoidance of tion function; motion planning; motion control. B. Task Planning Function [36]: C. Interaction and communication function [37].

Justification for the Use of a Crawler Mobile Robot for EOD Actions
Anti-terrorism intervention requires the use of robots to limit risks reasons: performing procedures during IED intervention missions, wh vation and inspection, X-ray analysis, disruption, etc.; no matter how ca is in responding to the IED, there is always the possibility that the attack so that he can operate the explosion-proof device remotely; even if a rob ize an IED, it can still be used to provide information on the choice of p vices needed to evacuate/eliminate the dangerous object from the threa

Features of Crawler Mobile Robots
Named mobile robots and controlled/autonomous vehicles, robot t have a structure consisting of ( Figure 2): Figure 2. The general structure of an EOD mobile robot [https://www.telerob.co odor-evo (accessed on 18 February 2021)] mechanical and drive system [38]; locat environmental perception and security system [40]; data interpretation and task m [41]. Operation in the environment is defined by agility and maneuverability: agi the mobile robot to overcome obstacles [42]; maneuverability is defined by the m quired for a maneuver [43].
Mobile intervention robots have the following main features: deg lowing a varied trajectory in terms of shape, length, and number of points [44]; speed: it is between 1-10 m/s, depending on the environment Figure 2. The general structure of an EOD mobile robot [https://www.telerob.com/en/products/ teodor-evo (accessed on 18 February 2021)] mechanical and drive system [38]; location system [39]; environmental perception and security system [40]; data interpretation and task management system [41]. Operation in the environment is defined by agility and maneuverability: agility is the ability of the mobile robot to overcome obstacles [42]; maneuverability is defined by the minimum area required for a maneuver [43].
Mobile intervention robots have the following main features: degree of mobility: following a varied trajectory in terms of shape, length, and number of parking/stopping points [44]; speed: it is between 1-10 m/s, depending on the environment in which it moves inside/outside [45]; autonomy: is the dependence on own power sources or the length of the power cord [46]; remote control and automation of operations [47].

Requirements for Crawler Mobile Robots, Resulting from an Anonymized Market Study
The robot should be affordable, if the designers meet the following requirements, simultaneously or individually: is intended only for specific missions and threats, for example pyrotechnic intervention [48]; is built modularly [49]; subsystems to be redesigned so that the solution is as simple and reliable as possible [50]; can use a disruptor [51]; should be equipped with video cameras [52]; must have an adequate lifting capacity [53]; can use X-ray systems [54]; should be equipped with omnidirectional cameras [55]; the robot must be able to communicate with an operator [56]; can easily climb stairs it can be said that only 10% of the threats targeted easily accessible open areas; should be easy to maintain and repair; must operate in a wide range of terrains [57]; arm should have high mobility [58].

Geometric Configuration of the Crawler Propeller
In order to achieve the geometric configuration of the crawler engine, one must consider the influence of the geometric characteristics of the tracked engine on the following: mobility of the robot on terrain with various configurations and consistencies; stability of the robot during movement and during the execution of the specific mission. The effects of the terrain on the robot can be grouped into the categories presented in Figure 3.
Appl. Sci. 2021, 11, x FOR PEER REVIEW 5 of 32 inside/outside [45]; autonomy: is the dependence on own power sources or the length of the power cord [46]; remote control and automation of operations [47].

Requirements for Crawler Mobile Robots, Resulting from an Anonymized Market Study
The robot should be affordable, if the designers meet the following requirements, simultaneously or individually: is intended only for specific missions and threats, for example pyrotechnic intervention [48]; is built modularly [49]; subsystems to be redesigned so that the solution is as simple and reliable as possible [50]; can use a disruptor [51]; should be equipped with video cameras [52]; must have an adequate lifting capacity [53]; can use X-ray systems [54]; should be equipped with omnidirectional cameras [55]; the robot must be able to communicate with an operator [56]; can easily climb stairs it can be said that only 10% of the threats targeted easily accessible open areas; should be easy to maintain and repair; must operate in a wide range of terrains [57]; arm should have high mobility [58].

Geometric Configuration of the Crawler Propeller
In order to achieve the geometric configuration of the crawler engine, one must consider the influence of the geometric characteristics of the tracked engine on the following: mobility of the robot on terrain with various configurations and consistencies; stability of the robot during movement and during the execution of the specific mission. The effects of the terrain on the robot can be grouped into the categories presented in Figure 3.  [59]. This representation aims to allow us to establish algorithms for defining the kinematic and dynamic model depending on the type of terrain on which the crawler robot will move. Analyzing the requirements formulated by the potential beneficiaries, as well as the current stage of technological development of mobile robots, the main functional parameters were quantified, and the main functional characteristics were estimated ( Table 1).
The global analysis of the problem of locomotion on surfaces leads to the identification of four types of forces, among them including the propulsive force: Propulsion; Adhesion; Cohesion; Support.   [59]. This representation aims to allow us to establish algorithms for defining the kinematic and dynamic model depending on the type of terrain on which the crawler robot will move.
Analyzing the requirements formulated by the potential beneficiaries, as well as the current stage of technological development of mobile robots, the main functional parameters were quantified, and the main functional characteristics were estimated ( Table 1).
The global analysis of the problem of locomotion on surfaces leads to the identification of four types of forces, among them including the propulsive force: Propulsion; Adhesion; Cohesion; Support.

Conditions Regarding the Crossing of the Step Type Obstacle
The step type obstacle is often encountered in urban environments (curbs, stairs in buildings, etc.), which requires a detailed study of this process for an optimal geometric configuration of the crawler engine ( Figure 4). The crossing of the step-type obstacle presupposes the obligatory completion of two successive stages: the approach to the obstacle; crossing the obstacle.

Conditions Regarding the Crossing of the Step Type Obstacle
The step type obstacle is often encountered in urban environments (curbs, stairs in buildings, etc.), which requires a detailed study of this process for an optimal geometric configuration of the crawler engine ( Figure 4). The crossing of the step-type obstacle presupposes the obligatory completion of two successive stages: the approach to the obstacle; crossing the obstacle. [ ] where: asc T N     -the ascending force, manifested in front of the tensioning roller, at the contact of the track with the obstacle. The limiting condition for them of climbing the obstacle is: where: T t [N]-traction force, manifested at the wheel; G[N]-the weight of the robot. The ascending force is given by the following relation: where: T asc [N]-the ascending force, manifested in front of the tensioning roller, at the contact of the track with the obstacle. The limiting condition for them of climbing the obstacle is: The coefficient of friction between the tracked thruster and the obstacle ( Figure 5), µ [−], is given by the following calculation relation [60][61][62]: angle of inclination of the ascending branch of the track to the axis Ox; G x m     -distance from the CG to the axle of the drive wheel, on the axle Ox; a L m     -the distance from the axle of the drive wheel to the last roller, the one at the beginning of the ascending branch of the track, on the axis Ox; a l m     -distance from the center of the last roller to the center of the tension roller, on the axis Ox. The coefficient of friction between the tracked thruster and the obstacle ( Figure 5), μ [−], is given by the following calculation relation [60][61][62]: where: h m     -the height of the obstacle step, on the axis Oy; Thus, (5) becomes: Which is denoted by λ, the ratio: Thus, (5) becomes: Appl. Sci. 2021, 11,3757 8 of 32 In order to assess the influence of the length of grip and the position of the center of gravity, the height of the obstacle shall be considered to be: h = 1, 5 · r m . It is denoted as γ = r m /L , so that inequality (7) becomes: The above relation allows for the evaluation of the influence that the position of the center of mass has on the conditions of escalation of the obstacle (Figure 6). In order to assess the influence of the length of grip and the position of the center of gravity, the height of the obstacle shall be considered to be: 1,5 m h r = ⋅ . It is denoted as γ = m r L, so that inequality (7) becomes: The above relation allows for the evaluation of the influence that the position of the center of mass has on the conditions of escalation of the obstacle ( Figure 6). Given the notation presented in Figure 7, the following equations result: [ ]  Four different values were considered for the report γ = r m /L [−] to highlight how the CG position leads to a change in the coefficient of friction between the tracked thruster and the obstacle µ.
Given the notation presented in Figure 7, the following equations result: where: r [m]-the running radius of the support wheel (bucket), including the thickness of the track; h [m]-the height of the step obstacle. Analyzing the way in which the vehicle climbs onto the obstacle, the following distinct situations can be distinguished: s G < s-the vehicle can climb over the obstacle; s G > sthe vehicle cannot climb over the obstacle; s G = s-critical condition, at the limit.
From the analysis of the Equations (9)-(12), from the graphical representation of these equations ( Figure 8) and of the presented limit conditions, it results in (13): x G sin θ cos θ − y G sin 2 θ = (h − r) cos θ + r cos 2 θ [m].
Solving Equations (13)-(14) was performed for a running radius of 0.0425 m ( Figure 9).   From the analysis of the Equations (9)-(12), from the graphical representation of these equations ( Figure 8) and of the presented limit conditions, it results in (13): Solving Equations (13)-(14) was performed for a running radius of 0.0425 m ( Figure 9).  . The variations inf the two graphs mean that, as the obstacle escalates, the distance increases s G horizontally between the rear point of contact and the edge of the obstacle decreases to zero, at which point it can be stated that the robot remains stable at the obstacle stage and the distance s from the center of the driving wheel to the point where the lower branch of the track is tangent to the edge of the obstacle is moving towards the point of minimum, and "0", followed with increasing distance from the edge of the obstacle, the proximity of the edge following the corresponding allure.
How to vary the maximum angle of arrangement of the support branch of the track to the ground θ is shown in Figures 9 and 10. It can be seen that the angle of inclination decreases as the center of mass moves forward.
Appl. Sci. 2021, 11, x FOR PEER REVIEW  The schematic of the tracked platform geometry for the trench crossing limit is presented in Figure 11. In the initial phase, the vehicle (drawn in blue) remains h until the vertical passing through the center of mass coincides with the edge of t The vehicle starts to oscillate around the point of contact with the edge of the dit marked with P). The limit position, at which it is still possible to cross the ditch ( red) occurs when contact is made with the other edge of the ditch at a point o cumference of the front wheel on its horizontal axis of symmetry. The above-m approach scenario neglects inertial forces due to the low travel speeds of the mob   The schematic of the tracked platform geometry for the trench crossing limit s is presented in Figure 11. In the initial phase, the vehicle (drawn in blue) remains ho until the vertical passing through the center of mass coincides with the edge of th The vehicle starts to oscillate around the point of contact with the edge of the ditc marked with P). The limit position, at which it is still possible to cross the ditch (d red) occurs when contact is made with the other edge of the ditch at a point on cumference of the front wheel on its horizontal axis of symmetry. The above-me approach scenario neglects inertial forces due to the low travel speeds of the mob platform. For the limit situation, the following geometric equations can be writte The schematic of the tracked platform geometry for the trench crossing limit situation is presented in Figure 11. In the initial phase, the vehicle (drawn in blue) remains horizontal until the vertical passing through the center of mass coincides with the edge of the ditch. The vehicle starts to oscillate around the point of contact with the edge of the ditch (point marked with P). The limit position, at which it is still possible to cross the ditch (drawn in red) occurs when contact is made with the other edge of the ditch at a point on the circumference of the front wheel on its horizontal axis of symmetry. The above-mentioned approach scenario neglects inertial forces due to the low travel speeds of the mobile robot platform. For the limit situation, the following geometric equations can be written: for the general case, in which it was assumed that h r > r m h r > r m .  Eliminating the unknown φ, the width of the ditch that can be crossed was calculate according to the horizontal position of the center of mass and using the notatio  There is an inversely proportional dependence between the maximum width of th ditch that can be crossed and the horizontal distance from the rear wheel axle and th center of mass. It turns out that the forward movement of the center of mass leads to a increase in the height of the step that can be climbed, but also to a decrease in the wid of the ditch that can be crossed.

Conditioning Imposed by the Average Pressure on the Ground
The average pressure exerted by the tracks on the ground is given by the followin relation: -adhesion length of the track to the ground. Using the relation (17) the "Contour Plot" type graph was obtained ( Figure 13). Eliminating the unknown ϕ, the width of the ditch that can be crossed was calculated according to the horizontal position of the center of mass and using the notation γ = L/L 1 , the results shown in Figure 12 are obtained.  Eliminating the unknown φ, the width of the ditch that can be crossed was calculated according to the horizontal position of the center of mass and using the notation  There is an inversely proportional dependence between the maximum width of the ditch that can be crossed and the horizontal distance from the rear wheel axle and the center of mass. It turns out that the forward movement of the center of mass leads to an increase in the height of the step that can be climbed, but also to a decrease in the width of the ditch that can be crossed.

Conditioning Imposed by the Average Pressure on the Ground
The average pressure exerted by the tracks on the ground is given by the following relation: where: b [m]-width of the track; La [m]-adhesion length of the track to the ground. Using the relation (17) the "Contour Plot" type graph was obtained ( Figure 13). There is an inversely proportional dependence between the maximum width of the ditch that can be crossed and the horizontal distance from the rear wheel axle and the center of mass. It turns out that the forward movement of the center of mass leads to an increase in the height of the step that can be climbed, but also to a decrease in the width of the ditch that can be crossed.

Conditioning Imposed by the Average Pressure on the Ground
The average pressure exerted by the tracks on the ground is given by the following relation: where In Figure 13, it can be naturally concluded that the area located in the upper right, for kPa , is the most advantageous. An average-low ground pressure can be obtained by increasing the adhesion length and/or by increasing the track width. However, reporting to military vehicles is not able to generate consistent values for the recommended average ground pressure due to the "scale effect" [62,63] (Figure 14).

Geometric Conditions Imposed by the Execution of the Turn
From the point of view of cornering, there are two major conditioning factors: the position of the center of mass and the gauge (the distance between the planes of symmetry of the two tracks).
The position of the center of mass (CG) directly conditions the distribution of the pressure exerted by the support branch of the track on the ground. The value of the displacement of the turning poles is obtained by solving the following equation [64]: In Figure 13, it can be naturally concluded that the area located in the upper right, for which p med < 6 [kPa], is the most advantageous. An average-low ground pressure can be obtained by increasing the adhesion length and/or by increasing the track width.
However, reporting to military vehicles is not able to generate consistent values for the recommended average ground pressure due to the "scale effect" [62,63] (Figure 14). In Figure 13, it can be naturally concluded that the area located in the upper right, for kPa , is the most advantageous. An average-low ground pressure can be obtained by increasing the adhesion length and/or by increasing the track width. However, reporting to military vehicles is not able to generate consistent values for the recommended average ground pressure due to the "scale effect" [62,63] (Figure 14).

Geometric Conditions Imposed by the Execution of the Turn
From the point of view of cornering, there are two major conditioning factors: the position of the center of mass and the gauge (the distance between the planes of symmetry of the two tracks).
The position of the center of mass (CG) directly conditions the distribution of the pressure exerted by the support branch of the track on the ground. The value of the displacement of the turning poles is obtained by solving the following equation [64]:

Geometric Conditions Imposed by the Execution of the Turn
From the point of view of cornering, there are two major conditioning factors: the position of the center of mass and the gauge (the distance between the planes of symmetry of the two tracks).
The position of the center of mass (CG) directly conditions the distribution of the pressure exerted by the support branch of the track on the ground. The value of the displacement of the turning poles is obtained by solving the following equation [64]: and the moment of resistance in the turn is determined by the relationship: where µ [−] = the steering resistance coefficient, and k [−] = a coefficient that takes into account the displacement of the turning poles.
It can also be seen that a relative displacement of a maximum of 0.27 to the front contributes to the decrease in the resistant movement in cornering Figure 15. The track gauge, denoted by B, determines the magnitude of the traction forces on the two tracks: where and the moment of resistance in the turn is determined by the relationship: where μ [−] = the steering resistance coefficient, and k [−] = a coefficient that takes into account the displacement of the turning poles.
[ ] It can also be seen that a relative displacement of a maximum of 0.27 to the front contributes to the decrease in the resistant movement in cornering Figure 15. The track gauge, denoted by B, determines the magnitude of the traction forces on the two tracks: [ ] where   For constant values of the coefficient k, the weight of the platform and the maximum coefficient of cornering resistance, the value of the traction forces at the two tracks depends on the ratio La/B and the specific turning radius (Figure 16): For constant values of the coefficient k, the weight of the platform and the maximum coefficient of cornering resistance, the value of the traction forces at the two tracks depends on the ratio L a /B and the specific turning radius (Figure 16): It follows that it is rational to adopt a track gauge value as close as possible to the value of the track length of the track.

Static stability Study of the Crawler Engine
The geometric characteristics of the crawler propeller, as well as the positio center of mass of the mobile robot, are critical for ensuring stability in static mode ment on the longitudinal slope; crossing the slope; turning with a stable radius; ca dling.
From the point of view of the stability of the tracked platform when movin longitudinal slope, the most difficult situation occurs when braking during the de the slope (Figure 17), which is denoted for the deceleration of the platform during . At the limit, the misalignment x of the ground pressure ce comes equal to L-L1, so that the equation of equilibrium of the moments with re the point P of the forces acting on the platform results in the expression: It can be concluded that the increase in the height of the center of gravity, as its movement towards the front of the platform leads to a substantial decrease in t ing deceleration at which the overturning occurs (Figure 18).

Static Stability Study of the Crawler Engine
The geometric characteristics of the crawler propeller, as well as the position of the center of mass of the mobile robot, are critical for ensuring stability in static mode: movement on the longitudinal slope; crossing the slope; turning with a stable radius; cargo handling.
From the point of view of the stability of the tracked platform when moving on the longitudinal slope, the most difficult situation occurs when braking during the descent of the slope (Figure 17), which is denoted for the deceleration of the platform during braking: At the limit, the misalignment x of the ground pressure center becomes equal to L-L1, so that the equation of equilibrium of the moments with respect to the point P of the forces acting on the platform results in the expression:   Resuming the calculations that led to the plot of the graph presented above, we obtain the variation of the maximum deceleration when braking on the horizontal terrain, graphically presented in Figure 19.
The deceleration during braking is constant and the initial speed is v; it follows that the minimum time required for braking is given by the relation: [ ] Stability on the transverse slope is a particular case of the issue of lateral stability. The geometric scheme, as well as the forces acting on the platform during the crossing of the slope, are shown in Figure 20. The overturning stability condition is satisfied as long as the resultant of the ground reactions is inside the support polygon: It can be concluded that the increase in the height of the center of gravity, as well as its movement towards the front of the platform leads to a substantial decrease in the braking deceleration at which the overturning occurs ( Figure 18).
Resuming the calculations that led to the plot of the graph presented above, we obtain the variation of the maximum deceleration when braking on the horizontal terrain, graphically presented in Figure 19.  Resuming the calculations that led to the plot of the graph presented above, we obtain the variation of the maximum deceleration when braking on the horizontal terrain, graphically presented in Figure 19.
The deceleration during braking is constant and the initial speed is v; it follows that

Simulation of the Slope Ascent
In order to evaluate the simulation potential of the simulation performed on the basis of a simple 2D model, a two-axle vehicle was schematized in the situation of longitudinal displacement on the slope Figure 21.
[ ] [ ] The deceleration during braking is constant and the initial speed is v; it follows that the minimum time required for braking is given by the relation: Stability on the transverse slope is a particular case of the issue of lateral stability. The geometric scheme, as well as the forces acting on the platform during the crossing of the slope, are shown in Figure 20. The overturning stability condition is satisfied as long as the resultant of the ground reactions is inside the support polygon:

Simulation of the Slope Ascent
In order to evaluate the simulation potential of the simulation performed on the basis of a simple 2D model, a two-axle vehicle was schematized in the situation of longitudinal displacement on the slope Figure 21.
[ ] For a transverse slope angle of 30 • , it results in h g = 0.866 · (B + b), which does not imply severe conditions.

Simulation of the Slope Ascent
In order to evaluate the simulation potential of the simulation performed on the basis of a simple 2D model, a two-axle vehicle was schematized in the situation of longitudinal displacement on the slope Figure 21. The data that were considered for the simulation are contained in Table 2.
From the analysis of the obtained results, it results that the all-wheel drive soluti is the most favorable.   Equations (28)-(30) allow for the determination of the expressions for the normal forces acting on the drive wheels and of the minimum coefficient of adhesion that ensures the capitalization of the traction forces: The data that were considered for the simulation are contained in Table 2. From the analysis of the obtained results, it results that the all-wheel drive solution is the most favorable.

Simulation of Crossing the Step-Type Obstacle
The simulation of crossing a step-type obstacle was performed in two variants ( Figure 22): when climbing the obstacle; and suspended on the obstacle.

Simulation of Crossing the Step-Type Obstacle
The simulation of crossing a step-type obstacle was performed in two variants (  Using the schematic in Figure 22, the following geometric relationships are calculated: The equilibrium equations for the forces and moments acting on the vehicle are as follows: The following notations are introduced: From Equations (35)-(42), the following second-degree equation is finally obtained: with the next positive solution: 2 Figure 22. Schematic of crossing a step-type obstacle: (a) shows the passage over the obstacle with the first cheek, in front of the robot; (b) follows the approach of the obstacle with the driving wheel.
Using the schematic in Figure 22, the following geometric relationships are calculated: The equilibrium equations for the forces and moments acting on the vehicle are as follows: The following notations are introduced: From Equations (35)-(42), the following second-degree equation is finally obtained: with the next positive solution: Relationship (41) allows one to determine the coefficient of adhesion required to cross the obstacle. From Equations (36)- (38) result the expressions of the normal forces acting on the drive wheels: If the obstacle is crossed by a single axis, the following equations are used: The calculations were performed tabularly in Microsoft Excel. The results obtained are presented in Tables 3 and 4.  The data obtained allow for an assessment of the demands of the driving wheels that attack the obstacle; the coefficient of adhesion required for the development of the traction force; the requirements imposed on the energy aggregate (engine and transmission) to overcome the obstacle.
From the analysis of the obtained data, it can be seen that the most important variation is the coefficient of adhesion necessary to allow for the crossing of the obstacle. For the two situations studied, Figures 23 and 24 show the variation in the minimum adhesion coefficient that ensures the crossing of the obstacle, depending on its height.  As the height of the obstacle increases, so does the need for traction. The variation i the traction force required to cross the obstacle is shown in Figures 25 and 26.   As the height of the obstacle increases, so does the need for traction. The variation in the traction force required to cross the obstacle is shown in Figures 25 and 26.   As the height of the obstacle increases, so does the need for traction. The variation in the traction force required to cross the obstacle is shown in Figures 25 and 26.    As the height of the obstacle increases, so does the need for traction. The variation in the traction force required to cross the obstacle is shown in Figures 25 and 26.   From the analysis of the presented graphs, it can be concluded that crossing the obstacle with both tracks leads to the increase in the required traction force with a value of about 250-350 N, approximately constant depending on the height of the obstacle.
The simulations were performed for a disposition of the center of mass, arranged symmetrically with respect to the two axes, and the traction force was evenly distributed over the entire adhesion length of the track: the model is simple and easy to operate, providing important and relevant information; the correlation between the constructive parameters and the functional characteristics is easy to highlight and to be optimized at a coarse level; the simplicity of the model makes it quickly integrated into complex models for simulating mobility.

Simulation of Crossing the Step-Type Obstacle with Recurdyn
The virtual model of a crawler engine was made using the specialized program Recurdyn. After making the virtual model, we proceeded to check the arrangement of all elements in order to eliminate interference or incorrect positioning (Figure 27). The simulations were performed for a disposition of the center of mass, arranged symmetrically with respect to the two axes, and the traction force was evenly distributed over the entire adhesion length of the track: the model is simple and easy to operate, providing important and relevant information; the correlation between the constructive parameters and the functional characteristics is easy to highlight and to be optimized at a coarse level; the simplicity of the model makes it quickly integrated into complex models for simulating mobility.

Simulation of Crossing the Step-Type Obstacle with Recurdyn
The virtual model of a crawler engine was made using the specialized program Recurdyn. After making the virtual model, we proceeded to check the arrangement of all elements in order to eliminate interference or incorrect positioning ( Figure 27). These simulations refer to the decomposition of the traction forces on the three directions of the orthogonal axis system. Each track element (patina) displaces the tread in the three directions. The graphs in Figure 28 refer to those stated.  These simulations refer to the decomposition of the traction forces on the three directions of the orthogonal axis system. Each track element (patina) displaces the tread in the three directions. The graphs in Figure 28 refer to those stated. The simulations were performed for a disposition of the center of mass, arranged symmetrically with respect to the two axes, and the traction force was evenly distributed over the entire adhesion length of the track: the model is simple and easy to operate, providing important and relevant information; the correlation between the constructive parameters and the functional characteristics is easy to highlight and to be optimized at a coarse level; the simplicity of the model makes it quickly integrated into complex models for simulating mobility.

Simulation of Crossing the Step-Type Obstacle with Recurdyn
The virtual model of a crawler engine was made using the specialized program Recurdyn. After making the virtual model, we proceeded to check the arrangement of all elements in order to eliminate interference or incorrect positioning ( Figure 27). These simulations refer to the decomposition of the traction forces on the three directions of the orthogonal axis system. Each track element (patina) displaces the tread in the three directions. The graphs in Figure 28 refer to those stated.  Simulating the contact of a skid in the composition of the track with the ground allows for the extraction of information on vertical stresses on the ground (ground pressure), as well as the evaluation of reactions in the direction of travel, which allows for the study of the ground lift in the direction of traction.
The study of the contact between the skate and the buckets allows for the evaluation of the contact force with implications for the dimensioning of the rubber bandage, but also for the identification of possible shocks when the bucket passes over two skates due to the intersection between them (Figure 29).
Appl. Sci. 2021, 11, x FOR PEER REVIEW Simulating the contact of a skid in the composition of the track with the gr lows for the extraction of information on vertical stresses on the ground (grou sure), as well as the evaluation of reactions in the direction of travel, which allow study of the ground lift in the direction of traction.
The study of the contact between the skate and the buckets allows for the ev of the contact force with implications for the dimensioning of the rubber bandage for the identification of possible shocks when the bucket passes over two skates d intersection between them (Figure 29).   Simulating the contact of a skid in the composition of the track with the ground allows for the extraction of information on vertical stresses on the ground (ground pressure), as well as the evaluation of reactions in the direction of travel, which allows for the study of the ground lift in the direction of traction.
The study of the contact between the skate and the buckets allows for the evaluation of the contact force with implications for the dimensioning of the rubber bandage, but also for the identification of possible shocks when the bucket passes over two skates due to the intersection between them (Figure 29). The simulation study of the torque variation at the driving wheel indicates its important variations, in the conditions of a stationary movement, with constant speed (Figure 30). Studying the simulation of travel speed for a value of about 45% of the maximum travel speed indicates the existence of irregularities that can have disruptive adverse effects on the image stability recorded by the video cameras installed on the platform (Figure 31). Studying the simulation of travel speed for a value of about 45% of the maximum travel speed indicates the existence of irregularities that can have disruptive adverse effects on the image stability recorded by the video cameras installed on the platform (Figure 31). An attenuation of these variations will be recorded by taking into account the moment of inertia of the electric motor and gearboxes.

Testing and Evaluation Propulsion Systems
The following main objectives of the experimental research were determined: the functional characteristics of the mobile platform; the functional characteristics of some main components of the mobile platform; The testing of the mobility of the mobile robot had the following important objectives: the operation of the propulsion system when moving rectilinearly; when cornering; the control mode of the controller; the operation of the engine: in reverse and reverse; at rapid changes of the operating mode; the road holding of the mobile robot.

Testing and Evaluation on the Stand
The testing of electric motors had the following objectives: the operation of motors at supply voltages of 12 Vcc and 24 Vcc; the controller and the electrical connections between the motor and the controller; the way of simultaneously changing the speed of electric motors; how to differentiate the speed of electric motors.
Stand-up testing of electric motors followed, checking the way of making the electrical connections between the motor and the controller; the RS232 and ANALOG control modes of the motors; the operation of the motors in simultaneous and differentiated speed regime; the efficiency of the engine failure stop system.
The following operations were performed prior to the actual execution of the tests ( Figure 32): the smooth rotation of the shafts of the electric motors was verified; integrity of the electrical conductors connecting the electric motors was checked; motors were mounted on the test stand. The schematic of the electrical connections is included in Figure 33. The electrical connections were made with conductors of large section so as to avoid voltage drops when high currents occur.
In the case of designing the DasyLab application, a decision was made to monitor and record the measured values. Butherworth type 3 digital filters were used to reduce the noise associated with the acquired signals. A first set of data was purchased during the stand test of electric motors. Next, a vacuum test was performed at different speeds of the two engines. The results are shown in Figure 32 For these tests, the digital control of the controller was used through the RS232 interface of the computer. An attenuation of these variations will be recorded by taking into account the moment of inertia of the electric motor and gearboxes.

Testing and Evaluation Propulsion Systems
The following main objectives of the experimental research were determined: the functional characteristics of the mobile platform; the functional characteristics of some main components of the mobile platform; The testing of the mobility of the mobile robot had the following important objectives: the operation of the propulsion system when moving rectilinearly; when cornering; the control mode of the controller; the operation of the engine: in reverse and reverse; at rapid changes of the operating mode; the road holding of the mobile robot.

Testing and Evaluation on the Stand
The testing of electric motors had the following objectives: the operation of motors at supply voltages of 12 Vcc and 24 Vcc; the controller and the electrical connections between the motor and the controller; the way of simultaneously changing the speed of electric motors; how to differentiate the speed of electric motors.
Stand-up testing of electric motors followed, checking the way of making the electrical connections between the motor and the controller; the RS232 and ANALOG control modes of the motors; the operation of the motors in simultaneous and differentiated speed regime; the efficiency of the engine failure stop system.
The following operations were performed prior to the actual execution of the tests ( Figure 32): the smooth rotation of the shafts of the electric motors was verified; integrity of the electrical conductors connecting the electric motors was checked; motors were mounted on the test stand. The schematic of the electrical connections is included in Figure 33. The electrical connections were made with conductors of large section so as to avoid voltage drops when high currents occur.
In the case of designing the DasyLab application, a decision was made to monitor and record the measured values. Butherworth type 3 digital filters were used to reduce the noise associated with the acquired signals. A first set of data was purchased during the stand test of electric motors. Next, a vacuum test was performed at different speeds of the two engines. The results are shown in Figure 32 For these tests, the digital control of the controller was used through the RS232 interface of the computer.  From the analysis of the presented graph, the following can be noticed ( Figure 34): the value of the current varies relatively little with the speed due to the fact that the mechanical load of the electric motor is zero, so that the absorbed current has relatively small values; control through the RS232 interface provided by the RoboteQ program leads to the execution of the turn by differentiating the speeds as follows: the outer track of the turn: v v +Δ ; and the inner track of the turn: v v −Δ ; where v Δ it is proportional to the turn command ( Figure 35).  From the analysis of the presented graph, the following can be noticed ( Figure 34): the value of the current varies relatively little with the speed due to the fact that the mechanical load of the electric motor is zero, so that the absorbed current has relatively small values; control through the RS232 interface provided by the RoboteQ program leads to the execution of the turn by differentiating the speeds as follows: the outer track of the turn: v v +Δ ; and the inner track of the turn: v v −Δ ; where v Δ it is proportional to the turn command ( Figure 35). From the analysis of the presented graph, the following can be noticed ( Figure 34): the value of the current varies relatively little with the speed due to the fact that the mechanical load of the electric motor is zero, so that the absorbed current has relatively small values; control through the RS232 interface provided by the RoboteQ program leads to the execution of the turn by differentiating the speeds as follows: the outer track of the turn: v + ∆v; and the inner track of the turn: v − ∆v; where ∆v it is proportional to the turn command ( Figure 35).  From the analysis of the presented graph, the following can be noticed ( Figure 34): the value of the current varies relatively little with the speed due to the fact that the mechanical load of the electric motor is zero, so that the absorbed current has relatively small values; control through the RS232 interface provided by the RoboteQ program leads to the execution of the turn by differentiating the speeds as follows: the outer track of the turn: v v +Δ ; and the inner track of the turn: v v −Δ ; where v Δ it is proportional to the turn command ( Figure 35).

Engine Testing by Suspension Test
Suspended testing of electric motors followed the same things as in Section 5.1.
The results of the test for simulating rectilinear gait are shown in Figure 36. The analysis of the graphically represented data shows the dependence between speed and absorbed current, which can be explained by the increased level of friction torque in the gearboxes. Figure 37 shows examples of results obtained when simulating the turn in the suspended test.
The development of experimental research allowed the formulation of the following: the testing program was completed and complied with procedural requirements; when the electric motors are idle, they absorb a current of about 3 A rms; in the case of a rapid change of speed by about 10%, there were short-term increases in the absorbed current of up to 8 A rms; due to the technological and adjustment non-uniformity, the speeds of the two engines differ by about 1-2% when idling; no abnormal noises or overheating were found during the operation of the gearboxes. During the operation of the tracks, the test was suspended: the occurrence of the phenomenon of hooking the tip of the tooth flank of the crawler chain roller was noted, as the phenomenon was found both at the entry into

Engine Testing by Suspension Test
Suspended testing of electric motors followed the same things as in Section 5.1. The results of the test for simulating rectilinear gait are shown in Figure 36.

Engine Testing by Suspension Test
Suspended testing of electric motors followed the same things as in Section 5.1. The results of the test for simulating rectilinear gait are shown in Figure 36. The analysis of the graphically represented data shows the dependence between speed and absorbed current, which can be explained by the increased level of friction torque in the gearboxes. Figure 37 shows examples of results obtained when simulating the turn in the suspended test.
The development of experimental research allowed the formulation of the following: the testing program was completed and complied with procedural requirements; when the electric motors are idle, they absorb a current of about 3 A rms; in the case of a rapid change of speed by about 10%, there were short-term increases in the absorbed current of up to 8 A rms; due to the technological and adjustment non-uniformity, the speeds of the two engines differ by about 1-2% when idling; no abnormal noises or overheating were found during the operation of the gearboxes. During the operation of the tracks, the test The analysis of the graphically represented data shows the dependence between speed and absorbed current, which can be explained by the increased level of friction torque in the gearboxes. Figure 37 shows examples of results obtained when simulating the turn in the suspended test.
the gear and at the exit of the gear, given that the support branch of the track is a freeforming an arrow of about 35-40 mm, as can be easily seen from Figure 38; the current absorbed by the motors, corresponding to a speed regime close to the maximum speed, by 18-20 A rms.

Testing and Evaluation of Rectilinear Displacement Capacity
Rectilinear gait testing was followed: testing the robot's ability to move forward in a straight line; backwards in a straight line; the ability to accelerate the mobile robot; determination of the maximum speed. A data acquisition system assisted by a portable PC using the specialized program DasyLab was used to perform the measurements.
An example of recording data at rectilinear motion at maximum speed is shown in Figure 39. The maximum speed obtained was higher than 1 m/s. The development of experimental research allowed the formulation of the following: the testing program was completed and complied with procedural requirements; when the electric motors are idle, they absorb a current of about 3 A rms; in the case of a rapid change of speed by about 10%, there were short-term increases in the absorbed current of up to 8 A rms; due to the technological and adjustment non-uniformity, the speeds of the two engines differ by about 1-2% when idling; no abnormal noises or overheating were found during the operation of the gearboxes. During the operation of the tracks, the test was suspended: the occurrence of the phenomenon of hooking the tip of the tooth flank of the crawler chain roller was noted, as the phenomenon was found both at the entry into the gear and at the exit of the gear, given that the support branch of the track is a free-forming an arrow of about 35-40 mm, as can be easily seen from Figure 38; the current absorbed by the motors, corresponding to a speed regime close to the maximum speed, by 18-20 A rms. the gear and at the exit of the gear, given that the support branch of the track is a freeforming an arrow of about 35-40 mm, as can be easily seen from Figure 38; the current absorbed by the motors, corresponding to a speed regime close to the maximum speed, by 18-20 A rms.

Testing and Evaluation of Rectilinear Displacement Capacity
Rectilinear gait testing was followed: testing the robot's ability to move forward in a straight line; backwards in a straight line; the ability to accelerate the mobile robot; determination of the maximum speed. A data acquisition system assisted by a portable PC using the specialized program DasyLab was used to perform the measurements.
An example of recording data at rectilinear motion at maximum speed is shown in Figure 39. The maximum speed obtained was higher than 1 m/s.

Testing and Evaluation of Rectilinear Displacement Capacity
Rectilinear gait testing was followed: testing the robot's ability to move forward in a straight line; backwards in a straight line; the ability to accelerate the mobile robot; determination of the maximum speed. A data acquisition system assisted by a portable PC using the specialized program DasyLab was used to perform the measurements.
An example of recording data at rectilinear motion at maximum speed is shown in Figure 39. The maximum speed obtained was higher than 1 m/s.

Testing and Evaluation of the Ability to Make the Turn
Testing of ability to make the turn followed the same things as in Section 5.1.
The same data acquisition systems described above were used to perform the measurements. On-the-go testing at two different engine speeds was performed by analog control, maintaining a relatively long time the command to be able to record data at constant operating speeds. During the suspended test, the following steps were performed: straight forward movement followed by turning right and then left; rectilinear movement backwards followed by the execution of the right and then left turn; execution of the turn with minimum radius only by driving only one track. In the first two stages, the following aspects were pursued: ability to make turns with different radius; the quality of the crawler gear drive; firmness and accuracy of the analog control. In the third stage, the following aspects were further pursued: ability to execute the turn with a minimum radius; smooth, noiseless operation of the tracks; control of the controller in analog mode; efficiency of the track guidance and stretching mechanism. The turning radius was determined: where B [m]-the gauge of the mobile robot; v [m/s]-left track speeds (index 2) and right track (index 1), respectively.
From the analysis of the graphically represented data, it is found that, at the rectilinear course for which v2 = v1, the turning radius tends to take an infinite value ( Figure 40). During the test when performing the turn by operating a single track, it was found that a turning radius of 0.68÷0.72 (m) was achieved, depending on the landslide of the immobilized track. During testing the ability to travel for a long time, the robot performed the following travel categories for 80 min: rectilinear movement back and forth; turning left and right; crossing singular obstacles. When operating the robot at maximum speed, the electric motors absorb a current of about 50 A rms, representing less than 50% of the maximum current set for the controller (110 A) and about 35% of the maximum capacity of the controller (140 A), the values recorded differ from those determined by simulation with a maximum of 6.52%, which confirms the validity of the calculation model developed.

Testing and Evaluation of the Ability to Make the Turn
Testing of ability to make the turn followed the same things as in Section 5.1. The same data acquisition systems described above were used to perform the measurements. On-the-go testing at two different engine speeds was performed by analog control, maintaining a relatively long time the command to be able to record data at constant operating speeds. During the suspended test, the following steps were performed: straight forward movement followed by turning right and then left; rectilinear movement backwards followed by the execution of the right and then left turn; execution of the turn with minimum radius only by driving only one track. In the first two stages, the following aspects were pursued: ability to make turns with different radius; the quality of the crawler gear drive; firmness and accuracy of the analog control. In the third stage, the following aspects were further pursued: ability to execute the turn with a minimum radius; smooth, noiseless operation of the tracks; control of the controller in analog mode; efficiency of the track guidance and stretching mechanism. The turning radius was determined: where B [m]-the gauge of the mobile robot; v [m/s]-left track speeds (index 2) and right track (index 1), respectively. From the analysis of the graphically represented data, it is found that, at the rectilinear course for which v 2 = v 1 , the turning radius tends to take an infinite value ( Figure 40). During the test when performing the turn by operating a single track, it was found that a turning radius of 0.68 ÷ 0.72 (m) was achieved, depending on the landslide of the immobilized track. During testing the ability to travel for a long time, the robot performed the following travel categories for 80 min: rectilinear movement back and forth; turning left and right; crossing singular obstacles. When operating the robot at maximum speed, the electric motors absorb a current of about 50 A rms, representing less than 50% of the maximum current set for the controller (110 A) and about 35% of the maximum capacity of the controller (140 A), the values recorded differ from those determined by simulation with a maximum of 6.52%, which confirms the validity of the calculation model developed. Appl. Sci. 2021, 11, x FOR PEER REVIEW 28 of 32 Figure 40. Appearance during the test of the ability to move over a rectangular prism.

Experimental Research on the Ability to Approach Obstacles
Testing the ability of the mobile obstacle robot had the following more important objectives: testing the operation of the propulsion system when crossing obstacles; the control mode of the controller; the operation of the engine at rapid changes in operating mode; the road holding of the mobile robot when approaching obstacles ( Figure 40).
The rectilinear gait test aimed at testing the ability to approach the obstacle in terms of energy resource and the characteristics of the track's adhesion to the ground.
An example of data recorded at rectilinear displacement at maximum speed is shown in Figure 41. It is noted that, although the displacement speed was approximately constant (red line), the current shows significant variations due to the corresponding change in the overall resistance coefficient to advance.
The height of the obstacle was 160 mm and the average speed of approaching the obstacle was 0.363 m/s. During the obstacle approach, the absorbed current had an average value of 57.22 A with a maximum of over 120 A. During the obstacle approach the robot control was firm, and its speed remained at an approximately constant value, the variations being generated by the entry/exit of/in contact with the edges of the obstacle of the support rollers of the track.

Experimental Research on the Ability to Approach Obstacles
Testing the ability of the mobile obstacle robot had the following more important objectives: testing the operation of the propulsion system when crossing obstacles; the control mode of the controller; the operation of the engine at rapid changes in operating mode; the road holding of the mobile robot when approaching obstacles ( Figure 40).
The rectilinear gait test aimed at testing the ability to approach the obstacle in terms of energy resource and the characteristics of the track's adhesion to the ground.
An example of data recorded at rectilinear displacement at maximum speed is shown in Figure 41. It is noted that, although the displacement speed was approximately constant (red line), the current shows significant variations due to the corresponding change in the overall resistance coefficient to advance. Figure 40. Appearance during the test of the ability to move over a rectangular prism.

Experimental Research on the Ability to Approach Obstacles
Testing the ability of the mobile obstacle robot had the following more important objectives: testing the operation of the propulsion system when crossing obstacles; the control mode of the controller; the operation of the engine at rapid changes in operating mode; the road holding of the mobile robot when approaching obstacles ( Figure 40).
The rectilinear gait test aimed at testing the ability to approach the obstacle in terms of energy resource and the characteristics of the track's adhesion to the ground.
An example of data recorded at rectilinear displacement at maximum speed is shown in Figure 41. It is noted that, although the displacement speed was approximately constant (red line), the current shows significant variations due to the corresponding change in the overall resistance coefficient to advance.
The height of the obstacle was 160 mm and the average speed of approaching the obstacle was 0.363 m/s. During the obstacle approach, the absorbed current had an average value of 57.22 A with a maximum of over 120 A. During the obstacle approach the robot control was firm, and its speed remained at an approximately constant value, the variations being generated by the entry/exit of/in contact with the edges of the obstacle of the support rollers of the track.  The height of the obstacle was 160 mm and the average speed of approaching the obstacle was 0.363 m/s. During the obstacle approach, the absorbed current had an average value of 57.22 A with a maximum of over 120 A. During the obstacle approach the robot control was firm, and its speed remained at an approximately constant value, the variations being generated by the entry/exit of/in contact with the edges of the obstacle of the support rollers of the track.

Conclusions and Discussion
The engine test program was completed in full and complied with the procedural requirements. The test program had a complex character, including the running of motors, reducers and tracks. When the electric motors are idle, they absorb a current of about 3 rms. In the case of a rapid change in speed of about 10%, there were short-term increases in the absorbed current of up to 8 A rms.
When operating during the test, the current absorbed by the motors, corresponding to a speed regime close to the maximum speed, was suspended at 18-20 A rms. Thus, regardless of the speed regimes, when driving in a straight line and/or in a corner, as well as for both directions, no warm-ups of the motors or reducers were found. The temperature of the MOSFET power components in the controller exceeded the ambient temperature by 1-2 • C. The values of the absorbed current represent 12-15% of the maximum current allowed by the controller.
The values obtained differ from those calculated by a simulation with a maximum of 4.7%. Increased current values were recorded at the transient regimes. The tests followed the following functional algorithm: Through the program of experimental research, the following important issues related to the functional characteristics of the mobile platform were revealed: the constructive characteristics of the ROBTER crawler robot allowed for stable and fully controllable rolling; the ROBTER crawler robot did not lose its grip, and there was no skidding or tilting; the ability to cross the individual obstacles (longitudinal slope) of the ROBTER crawler robot is considered to be in accordance with the formulated requirements; The main advantages of the studied solution are the possibility of creating a family of intervention robots by replacing the operational platform; simplicity of the calculation logarithm; making modular software; the use of relatively cheap materials and components, the aim being to increase the degree of efficiency and annihilation of potential risks with minimal costs. In addition, this functional model can also be used for research activities in the subject, as well as for doctorates. As the structure is extremely versatile, future users develop it to conduct in-depth research. In further research, we want to focus on describing the influence of the crawler propeller on the ground and on the development of at least two new operational platforms.
The previously-performed and presented study had as main objective the highlighting of the influences that the main geometric parameters exert on the functional characteristics of the mobile robot. The following conclusions regarding the geometric configuration of the mobile robot platform result: the increase in the height at which the center of mass is arranged leads to more favorable conditions for approaching step-type obstacles but generates conditions of loss of stability when sloping and braking, especially when braking when descending the slope; increasing the height of the axis of the drive wheel leads to the corresponding increase of the height of the step-type obstacle that can be approached, but also to the increase of the width of the ditch that can be crossed; the forward movement of the horizontal position of the center of gravity leads to more advantageous conditions for tackling step-type obstacles, but appropriately reduces the width of the ditch that can be crossed and increases the value of the forces required to perform the turn; increasing the adhesion length of the crawler propeller with the ground leads to the corresponding increase in the width of the ditch that can be crossed but also to the increase in the traction forces in turning; the increase of the track width allows to obtain a lower average pressure on the ground, reducing the sinking of the tracked propeller in the deformable ground and, therefore, the resistance to advance; the lower sinking in the deformable soil also leads to the reduction of the lateral excavation effect during the execution of the turn, which leads to the decrease of the resistance moment in the turn.
All these conclusions highlight the contradictory nature of the influence exerted by the main geometric parameters of the crawler engine on the functional characteristics of the mobile robot. This results in the need to optimize the geometrical parameters of the crawler engine according to the characteristics of the specific mission for which the mobile robot is intended. All these considerations were taken into account when making the prototype, which is the subject of this paper.

Data Availability Statement:
The tests were performed with the testing program ROBTER and its components according to the requirements of stage IV of the Robot project to combat terrorist acts, contract 20/2006 within the CEEX program.