Isolation and Characterization of Oil-Degrading Enterobacter sp. from Naturally Hydrocarbon-Contaminated Soils and Their Potential Use against the Bioremediation of Crude Oil

: The contamination of crude oil in soil matrices is a persistent problem with negative repercussions because of the recalcitrant, hazardous, and mutagenic properties of its constituents. To mitigate the effect of crude oil contamination in soil, the use of microorganisms is a cheap and feasible option. In the current study, bacterial species from numerous polluted oil ﬁeld surfaces were isolated and examined for their ability to degrade crude oil. Random soil samples polluted with hydrocarbons were collected and various bacterial isolates were isolated. Results revealed that 40% of total isolates had potential use for hydrocarbon biodegradation, the synthesis of exopolysaccharides and the solubilization of phosphorous. Following isolation and characterization to degrade crude oil, a pot trial was conducted using maize inoculated with the four best strains—i.e., S 1 (PMEL-63), S 2 (PMEL-67), S 3 (PMEL-80), and S 4 (PMEL-79)—in artiﬁcially hydrocarbon-polluted soil with concentrations of crude oil of 0, 1000, and 2000 ppm. Results revealed that S 4 (PMEL-79) had signiﬁcant potential to degrade hydrocarbon in polluted soils. The root length, shoot length, and fresh biomass of maize were increased by 65%, 45%, and 98%, respectively, in pots inoculated with S 4 (PMEL-79) Enterobacter cloacae subsp., whereas the lowest root length was observed where no strain was added and the concentration of crude oil was at maximum. Moreover, S 4 (PMEL-79) Enterobacter cloacae subsp. was found to be the most effective strain in degrading crude oil and increasing maize growth under polluted soil conditions. It was concluded that the isolation of microorganisms from oil-contaminated sites should be considered in order to identify the most effective microbial consortium for the biodegradation of naturally hydrocarbon-contaminated soils. the potential remediation of hydrocarbons by


Introduction
With the modernization and advancement of industry, the contamination of soil with toxic pollutants has become a major problem for sustainable agriculture worldwide [1][2][3][4]. The contamination of soil has increased extensively in the past two decades and is a major (PAHs) and be more effective in the process of bioremediation, while their effects on maize growth may vary depending on the type of bacteria and inoculation conditions. Therefore, the specific objectives of current study are to (i) isolate the bacterial strains from crude oil-contaminated soil that are helpful for the effective remediation of crude oil and (ii) evaluate the efficacy of isolated bacterial strains on the performance of maize (Zea mays L.) cultivated in crude oil-polluted soil.

Soil Sampling
The soil samples were collected from various regions of the Punjab province of Pakistan ( Figure 1). The random sampling was carried out in the districts of Jhang, Faisalabad, and Multan from hydrocarbon-contaminated soils. Composite samples of 1 kg were prepared by sampling at different locations. Sampling sites were areas used for oily chemical sludge drainage and processing. Soil samples were collected using tube augar. The soil sampling thickness was up to 90 cm from the ground layer. The four soil samples obtained were used to extract 10 microbial isolates, and composite samples were used to test the total hydrocarbon content of petroleum (TPH). The collected soil samples were stored at 4 • C in the dark in zipped plastic bags prior to use for bacterial isolation and sample TPH contamination assessment.
Appl. Sci. 2021, 11, x FOR PEER REVIEW 3 of 15 soil. It is hypothesized that the isolates would acclimatize to polycylic-aromatic hydrocarbons (PAHs) and be more effective in the process of bioremediation, while their effects on maize growth may vary depending on the type of bacteria and inoculation conditions. Therefore, the specific objectives of current study are to (i) isolate the bacterial strains from crude oil-contaminated soil that are helpful for the effective remediation of crude oil and (ii) evaluate the efficacy of isolated bacterial strains on the performance of maize (Zea mays L.) cultivated in crude oil-polluted soil.

Soil Sampling
The soil samples were collected from various regions of the Punjab province of Pakistan ( Figure 1). The random sampling was carried out in the districts of Jhang, Faisalabad, and Multan from hydrocarbon-contaminated soils. Composite samples of 1 kg were prepared by sampling at different locations. Sampling sites were areas used for oily chemical sludge drainage and processing. Soil samples were collected using tube augar. The soil sampling thickness was up to 90 cm from the ground layer. The four soil samples obtained were used to extract 10 microbial isolates, and composite samples were used to test the total hydrocarbon content of petroleum (TPH). The collected soil samples were stored at 4 °C in the dark in zipped plastic bags prior to use for bacterial isolation and sample TPH contamination assessment.

Bacterial Isolation
The enrichment culture system was used to isolate the bacteria. Bacterial isolates were developed on an inorganic basal salt substrate (0.64 g K2HPO4, 0.31 g KH2PO4, 0.5 g NH4Cl, 0.2 g MgSO4.7H2O, 0.005 g FeSO4.7H2O) with 1% crude oil as a single source of carbon. Briefly, 10 g of each specimen was added to a sterile 250 mL Erlenmeyer flask containing 95 mL of inorganic basal media. In a flatbed end-to-end shaker, the flasks were shaken vigorously to homogenize the soil suspension. Following this, a 1/10 serial dilution

Bacterial Isolation
The enrichment culture system was used to isolate the bacteria. Bacterial isolates were developed on an inorganic basal salt substrate (0.64 g K 2 HPO 4 , 0.31 g KH 2 PO 4 , 0.5 g NH 4 Cl, 0.2 g MgSO 4 .7H 2 O, 0.005 g FeSO 4 .7H 2 O) with 1% crude oil as a single source of carbon. Briefly, 10 g of each specimen was added to a sterile 250 mL Erlenmeyer flask containing 95 mL of inorganic basal media. In a flatbed end-to-end shaker, the flasks were shaken vigorously to homogenize the soil suspension. Following this, a 1/10 serial dilution of this suspension was prepared from the above culture by taking 1 mL and adding it to 9 mL of sterile media to 10 −5 , which was used to inoculate basal salt medium agar plates. Crude oil extracted through a membrane of 0.2 µm was atomized as a sole source of carbon on solidified agar plates. To check the growth of bacteria, incubation was conducted in Petri plates at 28 ± 1 • C for 72 h. On the basis of the color, shape, and size of the colony, further purification was performed by stretching on the media (Table 1).  (Figure 2). For this purpose, 24 microtiter plates were used. The test compounds used in the current study were a combination of PAHs. Only 40 µL of polyaromatic hydrocarbon mixtures (1 g anthracene, 10 g flourene and 1 g phenanthrene dissolved per liter of pentane) were used in the primary two lanes to be used as a control. There were no Bushnell and Hass media in these wells, and there was no bacterial inoculation. In total, 720 µL of Bushnell and Hass and 80 µL of bacteriological broths were poured in the following two lanes as well as 40 µL of PAHs mixture. In the second control, using five and six lanes, each well of these lanes was supplemented with Bushnell and Hass medium and a PAHs mixture, but without bacterial inoculation. In each plate, a single bacterial isolate was added to each row. These plates were incubated at 28 ± 1 • C for three weeks. In each well, after the incubation period (21 days), 200 microliters of p-Ido-nitro-tetraazolium (p-INT) indicator was added.
Appl. Sci. 2021, 11, x FOR PEER REVIEW 4 of 15 of this suspension was prepared from the above culture by taking 1 mL and adding it to 9 mL of sterile media to 10 −5 , which was used to inoculate basal salt medium agar plates. Crude oil extracted through a membrane of 0.2 μm was atomized as a sole source of carbon on solidified agar plates. To check the growth of bacteria, incubation was conducted in Petri plates at 28 ± 1 °C for 72 h. On the basis of the color, shape, and size of the colony, further purification was performed by stretching on the media (Table 1).  (Figure 2). For this purpose, 24 microtiter plates were used. The test compounds used in the current study were a combination of PAHs. Only 40 μL of polyaromatic hydrocarbon mixtures (1 g anthracene, 10 g flourene and 1 g phenanthrene dissolved per liter of pentane) were used in the primary two lanes to be used as a control. There were no Bushnell and Hass media in these wells, and there was no bacterial inoculation. In total, 720 μL of Bushnell and Hass and 80 μL of bacteriological broths were poured in the following two lanes as well as 40 μL of PAHs mixture. In the second control, using five and six lanes, each well of these lanes was supplemented with Bushnell and Hass medium and a PAHs mixture, but without bacterial inoculation. In each plate, a single bacterial isolate was added to each row. These plates were incubated at 28 ± 1 °C for three weeks. In each well, after the incubation period (21 days), 200 microliters of p-Ido-nitro-tetraazolium (p-INT) indicator was added.

Exoplysaccharide Production Assay
Enterobacter sp. strains were grown at 30 • C in TSB/10 (Difco Laboratories, Detroit, USA) or an RCV medium modified by Weaver and colleagues (1975). The amounts of chemicals used were as follows: Nalidixic acid, kanamycin and tetracycline were, respectively, used at amounts of 50, 25, and 15 mg mL −1 for the appropriate antibiotic selection of rhizobial strains [43].

2.
Each bacterial strain was represented by a loop on the plates (three per plate at different places).

Measurement of Total Petroleum Hydrocarbons by Infrared Spectroscopy
In obtained soil samples, a Horiba-350 oil content analyzer (Horiba Ltd., Kyoto, Japan), was used to test TPH. The TPH-oil content analyzer utilizes infrared light to determine the TPH. In a china dish, 5 g of soil was taken and 5 g of sodium sulfate was added to absorb moisture in the soil. These were thoroughly mixed, and a mixture of soil and sodium sulfate was added to 40 mL of RDH-CCl 4 . This mixture was shaken for 30 min and filtered using Whatman filter paper No.40 (11 cm). In order to absorb moisture and biogenic hydrocarbons, 100 mesh size silica was placed in the funnel during filtration. The filtrate was filled in a cell of 1.5 cm and put in a device for reading in mg/kg. Dilutions were produced using RDH-CCl 4 to bring the concentration within the scope of the requirements and equipment. The instrument was calibrated before measuring TPH.

Experimental Setup and Observations
A pottrial was conducted in the growth room to further check the ability of bacterial isolates to degrade hydrocarbons and to improve maize growth. The pots measurements used in the study were 13 cm × 6 cm, with a vessel size of 13 cm and an internal diameter of 6 cm. These pots were filled with soil that was sieved to separate gravel and debris by using a 2 mm sieve. The seeds were inoculated with peat combined with a 10% sugar solution for inoculation. In total, 15 regular treatments with three repeats were used, as shown in Table 2. All the soil samples were contaminated with a known quantity of crude oil purchased from a local oil company. The levels of crude oil were 0, 1000, and 2000 ppm. The Pioneer-30Y87 variety of maize was used. The seeds were inoculated with the different isolates S 4 (PMEL-79), S 3 (PMEL-80), S 2 (PMEL-67) and S 1 (PMEL-63). The pots were watered regularly. The dose of fertilizer prescribed-i.e., N:P:K 150:100:50 kg ha −1 , respectively-was added using urea, di-ammonium phosphate, and sulfate of potash as a fertilizer source. After 30 days of sowing, the root and shoot length of maize was determined using a meter rod. The dried and fresh biomass was determined after harvesting the maize to observe the remediation effect of bacterial isolates on maize plants. The residual TPH was measured using the Horiba oil content analyzer OCMA-350. 16S rRNA sequencing was used to identify the most effective and efficient bacterial isolates. This approach included extracting DNA from bacterial isolates, conducting 16S rRNA amplification, and comparing sequenced genes to Gene Bank to find a match [43,44].

Statistical Analysis
The recorded observations were statistically analyzed using Fisher's analysis of variance, and the means of treatments were compared with a 5% probability level according to the least significant difference test [45]. A principal component analysis (PCA) was carried out to group the strains according to their performances for physico-chemical parameters such as TPH concentration, biomass production, shoot length, root length, and chlorophyll content, and we investigated possible correlations between studied attributes. The principal component analysis was performed using XLSTAT software (Addinsoft).

Bioremediation Assay, Exopolysaccharides, and Phosphate Solubilizing Ability
The color brightness was due to the higher, medium, and lower range. The most extreme color wells are marked as (+ + +), demonstrating the capacity for further bacterial biodegradation ( Table 3). The test showed that four of the bacterial strains-i.e., N 1 , L 1 , H 2 , and M + O-showed an intense red color compared to the control and other strains, proving that these strains have the capacity to degrade crude oil (Figure 2b). Due to PAH oxidation, bacterial strain-inoculated wells turned red, showing that bacteria can biodegrade PAH, as shown in Figure 2b. The greater the intensity of the color, the higher the amount of degradation and vice-versa. These strains were later identified to be PMEL-63, PMEL-67, PMEL-79, and PMEL-80 from the genus Enterobacter sp. The test for exopolysaccharides production (EPS) was carried on these same strains-i.e., N 1 , L 1 , H 2 , and M + O-and showed that all these strains had the ability to produce exopolysaccharides as shown in Figure 2c. A clearing zone around the colonies indicated that the bacteria could solubilize phosphate. By subtracting the bacterial colony zone from the total diameter of the zone, the diameter of the clear zone could be determined. Tests with every bacterial strain were repeated three times in the experiment. The same strains-i.e., N 1 , L 1 , H 2 , and M + O-showed the ability to solubilize phosphate, as shown in Figure 2e. Table 3. Results of the bacterial isolate screening for the bioremediation assay, exopolysaccharides production, and phosphate solubilization.

Growth Attributes of Maize
Bacterial inoculation significantly improved the roots of inoculated maize crop. Under higher contamination of crude oil, bacterial strains S 4 (PMEL-79), S 3 (PMEL-80), S 2 (PMEL-67), and S 1 (PMEL-63) significantly enhanced the root length of maize, which was recorded as 48.08%, 42.18%, 37.27%, and 30.15% higher than control S0L4, respectively. Of all the strains, the bacterial strain S 4 (PMEL-79) increased the root length more significantly then the other strains, as shown in Figure 3a, reaching a level that was 32.11% higher than control S0L0. The lowest root length was observed in treatment SoL4, where no strain was added and 2000 ppm of crude oil was applied. The bacterial inoculation significantly affected the root length in crude oil concentration; i.e., 1000 and 2000 ppm, respectively. The elongation of shoot of maize was significantly enhanced by bacterial strains S 3 (PMEL-80) and S 2 (PMEL-67), by 16.9% and 20.41% more than the control, respectively. The highest increases in shoot length were observed in strain S 4 L2, which was 33.94% higher than control S0L0 (Figure 3b). The results show that, overall, the S 4 (PMEL-79), strain performed very well as it increased the root and shoot length of maize under both lower and higher levels of crude oil contamination in soil.
the exopolysaccharide production and phosphate solubilization; ↓ represents no exopolysaccharide production and phos-phate solubilisation.

Growth Attributes of Maize
Bacterial inoculation significantly improved the roots of inoculated maize crop. Under higher contamination of crude oil, bacterial strains S4 (PMEL-79), S3 (PMEL-80), S2 (PMEL-67), and S1 (PMEL-63) significantly enhanced the root length of maize, which was recorded as 48.08%, 42.18%, 37.27%, and 30.15% higher than control S0L4, respectively. Of all the strains, the bacterial strain S4 (PMEL-79) increased the root length more significantly then the other strains, as shown in Figure 3a, reaching a level that was 32.11% higher than control S0L0. The lowest root length was observed in treatment SoL4, where no strain was added and 2000 ppm of crude oil was applied. The bacterial inoculation significantly affected the root length in crude oil concentration; i.e., 1000 and 2000 ppm, respectively. The elongation of shoot of maize was significantly enhanced by bacterial strains S3 (PMEL-80) and S2 (PMEL-67), by 16.9% and 20.41% more than the control, respectively. The highest increases in shoot length were observed in strain S4L2, which was 33.94% higher than control S0L0 (Figure 3b). The results show that, overall, the S4 (PMEL-79), strain performed very well as it increased the root and shoot length of maize under both lower and higher levels of crude oil contamination in soil. In the pot trial, the highest maize fresh biomass was produced in response to inoculation with bacterial strain S 4 (PMEL-79). This extreme rise in the fresh biomass of the maize was 98% compared to the uninoculated control, as shown in Figure 4a. Further bacterial strains that efficiently amplified the maize fresh biomass were S 3 (PMEL-80) and S 2 (PMEL-67), at 43.13% and 28.9% more than the control, respectively. The S 4 (PMEL-79) bacterial strain upheld its consistency in promoting plant growth with maize as it caused the maximum increase in the fresh biomass of maize. Of the bacterial isolates, the lowest increases in maize fresh biomass were observed in treatments S 1 L 2 and S 1 L 4 , at 11% and 13%, respectively, produced by the inoculation of strain S 1 (PMEL-63) as compared to the control. The greatest increase in the oven-dried biomass of maize was detected in response to inoculation with S 4 (PMEL-79) and S 1 (PMEL-63) bacterial strains, showing improvements of 52.89% and 51.33%, respectively, compared to the control. This increase was double that of the uninoculated control. Other bacterial strains performed efficiently except the bacterial strain S 3 (PMEL-80), where the maize oven-dried biomass was less by 9.39% than the control, as shown in (Figure 4a). In brief, the bacterial strains S 4 (PMEL-79) and S 1 (PMEL-63) were both consistent with maize in increasing the oven-dried biomass relative to the uninoculated control; nevertheless, the percentage of improvement with these steady bacterial strains over the uninoculated control diverged from parameter to parameter. Strains S 4 (PMEL-79) and S 1 (PMEL-63) were found to perform best in the hydrocarbon-contaminated soils, affecting all the crop parameters and significantly enhancing the growth as compared to uninoculated contaminated soil.
terial strains that efficiently amplified the maize fresh biomass were S3 (PMEL-80) and S2 (PMEL-67), at 43.13% and 28.9% more than the control, respectively. The S4 (PMEL-79) bacterial strain upheld its consistency in promoting plant growth with maize as it caused the maximum increase in the fresh biomass of maize. Of the bacterial isolates, the lowest increases in maize fresh biomass were observed in treatments S1L2 and S1L4, at 11% and 13%, respectively, produced by the inoculation of strain S1 (PMEL-63) as compared to the control. The greatest increase in the oven-dried biomass of maize was detected in response to inoculation with S4 (PMEL-79) and S1 (PMEL-63) bacterial strains, showing improvements of 52.89% and 51.33%, respectively, compared to the control. This increase was double that of the uninoculated control. Other bacterial strains performed efficiently except the bacterial strain S3 (PMEL-80), where the maize oven-dried biomass was less by 9.39% than the control, as shown in (Figure 4a). In brief, the bacterial strains S4 (PMEL-79) and S1 (PMEL-63) were both consistent with maize in increasing the oven-dried biomass relative to the uninoculated control; nevertheless, the percentage of improvement with these steady bacterial strains over the uninoculated control diverged from parameter to parameter. Strains S4 (PMEL-79) and S1 (PMEL-63) were found to perform best in the hydrocarbon-contaminated soils, affecting all the crop parameters and significantly enhancing the growth as compared to uninoculated contaminated soil.

TPH Removal in Association with Maize
Maize simplified the petroleum hydrocarbon degradation under the controlled conditions. A removal rate of up to 54% of TPH was observed with respect to the control of the combined effect of the S 4 (PMEL-79) bacterial strain and maize. The efficiency of maize alone was not notable because it triggered the elimination of 10% TPH compared to the control. This can also be seen by comparing only the combined maize effect and the isolation of S 4 (PMEL-79), which caused a removal rate of TPH of 44% more than that above (Figure 4c). S 4 (PMEL-79) bacterial isolation was the most effective; however, the efficacy of other bacterial strains such as S 3 (PMEL-80), S 2 (PMEL-67), and S 1 (PMEL-63) cannot be overlooked as these bacterial strains in association with hydrocarbons bio-remediated maize by 40%, 36%, and 39%, respectively, compared with un inoculated contaminated soil (Figure 4c).

Bacterial Sequencing
16s rRNA sequencing showed that the S 4 bacterial isolate was Enterobacter cloacae subsp. dissolvens, with a similarity of 97.31%; S 3 was also Enterobacter cloacae subsp. dissolvens, with a similarity of 99.7%; S 2 and S 1 were also Enterobacter cloacae subsp. dissolvens, with a similarity of 100% (accession number MT212231.1). A phylogenetic tree of all bacterial strains was constructed using Mega X computer-based software to further explain the relationship of strains with neighboring species based on their evolutionary history ( Figure 5).

Selection of TPH-Degrading and Growth-Promoting Strains
On the basis of the results of the bioremediation assay, a trial was conducted under crude oil-contaminated conditions; four strains (S 1 , S 2 , S 3 , and S 4 ) were used to verify the TPH degradation in maize. The principle component analysis was used to test the results. Factor coordinates of bacterial strains based on TPH content, root length, shoot length, biomass production, and chlorophyll content are presented in Table 4. The maximum coordinate value (5.82) was observed in S 4 (PMEL-79) followed by S 3 with an F 1 value of 0.96 (PMEL-80). Factorial planes clearly show their unique behavior in terms of the TPH degradation and growth promotion of maize. The total variability between F 1 and F 2 biplots is 90%. The Pearson's correlation matrix showed that variables other than chlorophyll content were positively correlated. We detected some correlation between the TPH content, biomass production, shoot length, and root length, while there was negative correlation for the chlorophyll content. The active coordinates retained by PCA were used to construct the biplot in Figure 6. Table 4. Factor coordinates of bacterial strains based on TPH content, root length, shoot length, biomass production, and chlorophyll content.

Discussion
Crude oil contamination in soil has been recognized as a key factor for plant growth reduction. The findings of this study show that crude oil contamination suppressed maize growth, with the effect being more pronounced at higher levels of soil pollution (Figures  3 and 4). This impact may be due to disturbances in water and nutrient absorption caused by oil in the soil, as well as soil nitrogen, and phosphorus depletion [46]. These results are in accordance with previous published studies [1,38,47] reporting that root morphology and plant biomass were reduced in soil contaminated with petroleum hydrocarbons. Plant growth and photosynthesis pigments-i.e., chlorophyll contents-may have been hindered by the presence of toxic petroleum hydrocarbon compounds [10]. The current study shows that the presence of microorganisms significantly improved the plant height, biomass, and root morphology of maize in crude oil-contaminated soil (Figures 3 and 4). In addition, the results also show that the presence of microbes stimulated the biodegra-

Discussion
Crude oil contamination in soil has been recognized as a key factor for plant growth reduction. The findings of this study show that crude oil contamination suppressed maize growth, with the effect being more pronounced at higher levels of soil pollution (Figures 3 and 4). This impact may be due to disturbances in water and nutrient absorption caused by oil in the soil, as well as soil nitrogen, and phosphorus depletion [46]. These results are in accordance with previous published studies [1,38,47] reporting that root morphology and plant biomass were reduced in soil contaminated with petroleum hydrocarbons. Plant growth and photosynthesis pigments-i.e., chlorophyll contents-may have been hindered by the presence of toxic petroleum hydrocarbon compounds [10]. The current study shows that the presence of microorganisms significantly improved the plant height, biomass, and root morphology of maize in crude oil-contaminated soil (Figures 3 and 4). In addition, the results also show that the presence of microbes stimulated the biodegradation of crude oil in the rhizosphere in all treatments except the control (Figure 4c). The higher degradation rate in the crude oil-contaminated soil might be attributed to the increased microbial activity as a result of seed inoculation with microbes [6,48]. The results of the bacterial isolate screening for the bioremediation assay, exopolysaccharides production, and phosphate solubilization can be seen clearly in Table 3. Bio-surfactant production has been observed in many Bacillus sp., especially in Bacillus subtilis L., which implies good potential for the bioremediation of organic contaminants such as fuel hydrocarbons due to its emulsifying properties by following mechanisms including bioaccumulation (the net accumulation of contaminants in the microorganisms' cells), biomineralization (the transfer of aqueous contaminates into crystalline or amorphous precipitates), biotransformation (the transformation of contaminates from a toxic to less toxic form), and biosorption (the binding of contaminates with cation-binding proteins present on the cell wall of microorganisms) [22,49].
The current experiment demonstrates that the concentration of crude oil and total biomass production are directly related to each other. A lower concentration of crude oil proved to be less toxic as regards biomass production. Contrary to our findings, Gao and Zhu [50] observed no substantial effects of a reduced amount of crude oil on plant biomass, but the inhibition of growth was noticeable at higher concentrations of crude oil. The inherent toxicity of crude oil might be the cause of lower plant biomass production, as was clearly seen with higher concentrations of crude oil [2]. Plants are sensitive to lowmolecular-weight volatile hydrocarbons that are soluble in hydrophobic plant materials and can infiltrate cell membranes [10]. Cheema et al. [21] proposed secondary adverse effects of PAHs; PAHs might reduce the capacity of contaminated soil to offer water and nutrients to plants, leading to a reduction in biomass production.
Additionally, in the current experiment, it was observed that plants did not show obvious signs of toxicity stress-i.e., necrosis-suggesting that this species can be grown in crude oil-contaminated soils and as a result is a feasible option for the phytoremediation of petroleum hydrocarbons. Various legumes and cereals species can be effectively used for the phytoremediation of petroleum hydrocarbons [1,30]. The phytoremediation of petroleum hydrocarbons is significantly regulated by various factors such as environmental conditions, agronomic practices, plant species, and soil characteristics, affecting the petroleum hydrocarbon uptake in the rhizosphere [14,31].
The screening of these four strains showed that the all the strains were found to be Enterobacter cloacae subsp. The results showed that S 4 (PMEL-79) was recognized to be from the genus Enterobacter cloacae subsp. dissolvens with a similarity of >97%. Meanwhile, the other strains S 1 (PMEL-63), S 2 (PMEL-67) and S 3 (PMEL-80) were also from the genus Enterobacter cloacae subsp. Dissolvens; the similarity percentage was 100% for S 1 (PMEL-63), but for S 2 (PMEL-67) and S 3 (PMEL-80), this value was 99.72%. These strains are all from the same genus Enterobacter sp. Huang et al. [30] conducted an experiment to evaluate the bioremediation potential of Bacillus subtilis, Pseudomonas aeruginosa and Acinetobacter lwoffi individually and in combination to degrade crude oil. Hydrocarbon-contaminated soil and water was used for the inoculation of these bacteria. In addition, greater degradation by the combination of these bacterial strains was observed as compared to individual bacteria; however, at rates of 77.8% and 76.7%, respectively, crude oil degradation was detected in the experimental units receiving a sole inoculation of Pseudomonas aeruginosa and Bacillus subtilis, respectively [30]. The proposed mechanism for the degradation of crude oil by Enterobacter cloacae subsp. may be cell uptake, which is comprised of two parts. The first phase is the immediate exposure of Enterobacter cloacae subsp. to massive hydrocarbon particles for absorption. In the second phase, the bacteria interact with small pseudo-soluble, quasi-soluble, or encapsulated hydrocarbons particles for absorption.
Finally, the crude oil is degraded down into CO 2 and H 2 O, which are basic hydrocarbons [51][52][53]. Moreover, soil contaminated with petroleum hydrocarbons should be kept properly aerated and moist to optimize the remediation of crude oil by microbes [10,31]. Ghazali et al. [54][55][56][57] also reported the effectiveness of Bacillus strains in the remediation of petroleum hydrocarbons. They used different species from dissimilar genera such as Pseudomonas, Micrococcus, and Bacillus and concluded an important role of species from the genus Bacillus sp as they observed a greater degradation of petroleum hydrocarbons (57%) by a combination dominated by Bacillus sp. as compared to a combination comprised of Pseudomonas and Micrococcus species. Furthermore, appropriate agronomic practices-i.e., optimum nutrient management in contaminated soil-significantly improve the microbial biomass and density, further enhancing the biodegradation potential of microbes in petroleum-contaminated soils [29,33,56,58,59].
Findings from the present research expand our awareness of the plant-microorganism interaction in petroleum-contaminated soils and provide new insights on the use of beneficial microorganisms to enhance the remediation of petroleum hydrocarbons and crop productivity under petroleum hydrocarbon stress; furthermore, the results open new areas for researching the significance of biological interactions in petroleum hydrocarboncontaminated ecosystems.

Conclusions
Due to the extreme threat to environmental and human safety, crude oil hydrocarbons are among the most alarming contaminants. The results of the present study showed that S 4 (PMEL-79) was recognized to be from the genus Enterobacter cloacae subsp. dissolvens with a similarity of >97%. Furthermore, S 4 (PMEL-79) increased the root length, shoot length, and fresh biomass of maize to a greater extent than the control. All of the strains selected-S 1 , S 2 , S 3 , and S 4 -exhibited exopolysaccharides production capability and phosphate solubilization. The current study showed that the potential remediation of hydrocarbons by various isolates of bacteria is an eco-friendly, cheap and alternative option in soils polluted with hydrocarbon.