Effect of compressive strain rate on auxetic foam

: Auxetic foams have previously been shown to have beneﬁts including higher indentation resistance than their conventional counterparts, due to their negative Poisson’s ratio, making them better at resisting penetration by concentrated loads. The Poisson’s ratio and Young’s modulus of auxetic open cell foams have rarely been measured at the high compressive strain rates typical during impacts of energy absorbing material in sporting protective equipment. Auxetic closed cell foams are less common than their open cell counterparts, and only their quasi-static characteristics have been previously reported. It is, therefore, unclear how the Poisson’s ratio of auxetic foam, and associated beneﬁts such as increased indentation resistance shown at low strain rates, would transfer to the high strain rates expected under impact. The aim of this study was to measure the effect of strain rate on the stiffness and Poisson’s ratio of auxetic and conventional foam. Auxetic open cell and closed cell polymer foams were fabricated, then compression tested to ~80% strain at applied rates up to 200 s − 1 , with Poisson’s ratios obtained from optical full-ﬁeld strain mapping. Open cell foam quasi-static Poisson’s ratios ranged from − 2.0 to 0.4, with a narrower range of − 0.1 to 0.3 for closed cell foam. Poisson’s ratios of auxetic foams approximately halved in magnitude between the minimum and maximum strain rates. Open cell foam quasi-static Young’s moduli were between 0.02 and 0.09 MPa, whereas closed cell foams Young’s moduli were ~1 MPa, which is like foam in protective equipment. The Young’s moduli of the auxetic foams approximately doubled at the highest applied strain rate of 200 s − 1 .

Contemporary protective equipment can use dilatant foams [17][18][19], which are like viscoelastic foams in that they have an effective viscosity, except this viscosity increases with shear strain rate [20][21][22]. Dilatant foams can be flexible during normal use but then stiffen during impacts, so uncomfortable stiff shells [7][8][9][10] are not needed to pass certification tests [9,10,23]. Soft-shell dilatant foam back protectors intended for sports use have been certified to EN-1621-2 [24] for motorbiking, as there is no application specific standard [2,3,9,10,23,25]. Other types of sporting PPE are also designed and certified under test conditions that may not represent infield collisions and falls [26][27][28][29]. The stiffness of dilatant foams can vary exponentially when impacted and compressed at the various temperatures and speeds possible during sporting collisions and falls [9,23]. Applying such rate dependent materials to PPE means products can change in performance between certification tests and actual use, with implications for injury risk, including users overestimating how well they are protected [3,26,29]. Developing PPE that is less likely to see such changes in performance between certification tests and infield collisions and falls could, therefore, reduce the occurrence of sporting injuries.
For isotropic materials, Poisson's ratio is between −1 and 0.5 [46], so indentation resistance should be highest for materials with NPR between −0.5 and −1. Replacing foam in PPE with auxetic foam with a higher magnitude of Poisson's ratio (i.e., ideally between −0.5 and −1), which is typically between 0.1 and 0.4 for conventional foam [47][48][49], could increase indentation resistance. As such, auxetic foam could offer high indentation resistance to protect against penetrating loads, and low Young's modulus flexibility during normal use or impacts with distributed loads, reducing the need for stiff shells. Combining auxetic and dilatant foams [50,51], or using auxetic foam in isolation, could improve the comfort of soft-shell PPE and reduce changes in performance between certification tests and actual use. The increased indentation resistance of auxetic foam could only improve soft-shell PPE if NPR is present when the material is compressed rapidly during impacts. Studies measuring NPR of foam during high strain rate compression have only tested open cell auxetic foams with relatively low magnitude NPRs (between 0 and −0.1) [36,37,52]. These studies did not control nor measure the applied strain rates, nor report that they were similar to those expected during sporting collisions and falls.
Auxetic open cell foam is the most studied auxetic foam and it has been used to show the favourable impact response associated with NPR [4,30,53]. Auxetic open cell foam is typically fabricated by a thermomechanical process involving volumetric compression of conventional open cell foam in a mould, which buckles cell ribs to impose a re-entrant cell structure, then thermal fixing (heating then cooling) of the imposed structure [54]. Compression can be equal in all axes to give isotropic auxetic foam [54] or different in each of the principal directions to impart anisotropy [55][56][57]. Typically imposed uniform (triaxial) compression reduces the foam's volume by a factor of two to five [54,56,58], equating to 20 to 40% compressive strain in each direction. Open cell foams with compressive isotropic (same in all three axes) Poisson's ratios as low as −0.7 have been reported [54,59,60]. Stretching foam in one direction during fabrication increases anisotropy [57] and can also increase the magnitude of Poisson's ratio [55].
Foams used in back protectors [9,23], and closed cell foam in other PPE, like football and cricket pads [4,6], are at least ten times stiffer than open cell foam [4,56,58]. Closed cell foams used in PPE typically have Young's moduli-the established measure of materials stiffness-close to or above 1 MPa [4,6,9,23]. Closed cell auxetic foam can be fabricated using a bespoke pressure vessel [61] or by steam processing [62,63]. Steam processing traps steam in closed cells, which condenses upon cooling to create a negative pressure differential, shrinking the foam without a mould while fixing the polymer to impart NPR [62,63]. Auxetic foams fabricated by steam processing can have similar stiffness (~1 MPa) to conventional foams in PPE [62], so they should be more suitable for this application than open cell auxetic foam.
Impact tests for certifying PPE, like back protectors (EN-1621-2 [24]), football shin guards (BS EN 13061:2009 [64]) and cricket thigh pads (BS 7928:2013 [65]), typically compress foam to densification (~80% of its thickness) in less than 5 ms [5,6,23,29,66], equating to a time-averaged engineering strain rate of~200 s −1 . During such impact tests, a drop mass is decelerated by the energy absorbing material within the product, imparting variable strain rates up to and above 200 s −1 that reduce to 0 s −1 at maximum compression. Despite the wealth of research into auxetic open cell foam, most of the previous work measured Poisson's ratio and Young's modulus quasi-statically (<1 s −1 , [34,54,60,[67][68][69][70]), or at intermediate (<10 s −1 , [52]) strain rates. Poisson's ratios of auxetic open cell foams, between 0 and −0.1, have been measured using marker tracking during impact tests at higher, but variable, strain rates of~100 s −1 [36,37]. Closed cell auxetic foam has only been characterised quasi-statically [61][62][63]. As such, it remains unclear how the desirable Young's modulus of auxetic closed cell foam and the NPR-that could increase indentation resistance and decrease peak force under impact-could change during sporting collisions, falls, and other impacts. It is important to understand how Young's modulus and Poisson's ratio of auxetic foams may change at the high strain rates expected under impact, to inform the design, and help explain the findings, of high-speed indentation and impact studies.
Here, we test auxetic open and closed cell foam at a range of compressive strain rates (0.05 to 200 s −1 ). We measure Young's modulus and Poisson's ratio at higher compression rates, and in a more controlled way, than previous work (e.g., [36,52,[61][62][63]71]). A dynamic mechanical analyser applied constant rate-controlled compression to foam samples, with concurrent high-speed optical full-field strain measurement. Full-field strain measurement by digital image correlation (DIC) [70,[72][73][74] gives more accurate strain measurement than tracking discrete markers. This work has implications for the application of auxetic foam to soft-shell PPE, such as potential improvements to consistency in performance between certification tests and actual use.

Fabrication: Open Cell Foams
Open cell polyurethane foams with two different cell structures were thermo-mechanically fabricated from 32 (z-axis) by 32 (x-axis) by 96 (y-axis) mm samples (PUR30FR, Custom Foams, as used in [35,55,75]). Fabrication conditions and, hence, imparted cell structures were selected based on previous work to give high magnitude NPR in all three orthogonal axes [58,67,76] or just one axis [55,57,62,77]. For the uniform triaxial conversions, compression to 40% engineering strain was imposed with aluminium moulds to modify cell shape in each axis (Figure 1a), giving a volumetric compression ratio (final/original volume) of five. Samples and moulds were heated in an oven (MCP Tooling Technologies LC/CD) for twenty minutes at 160 • C, then removed from the oven and cooled to room temperature (~30 min) [58]. Anisotropic foams were fabricated with 30% biaxial compression in the xand z-axes, and extension by a factor of two in the y-axis (Figure 1b), applied using four 2 mm diameter pins passed through the foam, as in [55]. For these anisotropic samples, oven temperature was increased to 180 • C to maximise shape fixing [58]. Cell rise direction was parallel to the 32 mm z-axis in supplied open cell foam, so it was compressed during the anisotropic conversions. Three samples were converted for each condition, but one sample of anisotropic foam was discarded due to creasing.
Triaxial foam partially re-expanded following conversion, whereas anisotropic foam partially re-expanded in both compressed axes and shrank in the axis with applied tension. Partial re-expansion was intended as it is associated with increased magnitude of NPR [58,76,78], but meant the sizes of samples converted with different conditions differed slightly. Triaxial cubes with~26 mm and anisotropic cubes with~21 mm sides were cut from cuboidal samples a week after fabrication with a utility knife (Stanley), with cuts made perpendicular to sample length only (y-axis, Figure 1) to ensure straight, undamaged sides. Unconverted cubes (~25 mm sided) of similar size to the triaxial cubes were also cut for comparative testing.
foam, so it was compressed during the anisotropic conversions. Three samples were converted for each condition, but one sample of anisotropic foam was discarded due to creasing.
Triaxial foam partially re-expanded following conversion, whereas anisotropic foam partially re-expanded in both compressed axes and shrank in the axis with applied tension. Partial re-expansion was intended as it is associated with increased magnitude of NPR [58,76,78], but meant the sizes of samples converted with different conditions differed slightly. Triaxial cubes with ~26 mm and anisotropic cubes with ~21 mm sides were cut from cuboidal samples a week after fabrication with a utility knife (Stanley), with cuts made perpendicular to sample length only (y-axis, Figure 1) to ensure straight, undamaged sides. Unconverted cubes (~25 mm sided) of similar size to the triaxial cubes were also cut for comparative testing.

Fabrication: Closed Cell Foams
Closed cell auxetic foam was fabricated by steam processing, based on previous work [62,63]. Three samples of low-density polyethylene closed cell foam, with similar Young's modulus and density to foam used in sporting PPE [6] (Plastazote LD-60, Algeos, 10 × 20 × 100 mm), were placed (partially submerged) in a cylindrical container (diameter 75 mm, height 150 mm) three-quarters filled with water (at 20 °C). The container was then sealed with aluminium foil and placed in an oven (MCP Tooling Technologies LC/CD) at 105 °C for five hours to steam the samples. After steaming, the samples were removed from the container and cooled in air on a drying rack, imparting triaxial compression as the trapped steam condensed. Following conversion, the foam samples had a concave cross-sectional profile (~1.5 mm deep, Figure 1), as expected [62,63]. A 15 × 15 × 8 mm quasi-cuboid (Figure 1c) with a concave cross-sectional profile (Figure 1d), but straight sides parallel to the 15 mm z dimension and 8 mm x dimension (see Figure 2a), was cut from the centre of samples for compression testing. Three samples of unconverted foam (20 × 20 × 10 mm), with similar mass and aspect ratio to auxetic samples were also cut for testing. As with the open cell foam, there were slight size differences between sample dimensions after

Fabrication: Closed Cell Foams
Closed cell auxetic foam was fabricated by steam processing, based on previous work [62,63]. Three samples of low-density polyethylene closed cell foam, with similar Young's modulus and density to foam used in sporting PPE [6] (Plastazote LD-60, Algeos, 10 × 20 × 100 mm), were placed (partially submerged) in a cylindrical container (diameter 75 mm, height 150 mm) three-quarters filled with water (at 20 • C). The container was then sealed with aluminium foil and placed in an oven (MCP Tooling Technologies LC/CD) at 105 • C for five hours to steam the samples. After steaming, the samples were removed from the container and cooled in air on a drying rack, imparting triaxial compression as the trapped steam condensed. Following conversion, the foam samples had a concave cross-sectional profile (~1.5 mm deep, Figure 1), as expected [62,63]. A 15 × 15 × 8 mm quasi-cuboid ( Figure 1c) with a concave cross-sectional profile (Figure 1d), but straight sides parallel to the 15 mm z dimension and 8 mm x dimension (see Figure 2a), was cut from the centre of samples for compression testing. Three samples of unconverted foam (20 × 20 × 10 mm), with similar mass and aspect ratio to auxetic samples were also cut for testing. As with the open cell foam, there were slight size differences between sample dimensions after fabrication, so aspect ratios and mass were kept constant between conventional and auxetic test samples. Sample storage and testing was in air-conditioned rooms and laboratories (20 • C, relative humidity between 10 and 30%).

Cell Structures
Images showing cell structures were collected to demonstrate cell morphology and then explain measured mechanical properties based on established theory [47]. Microscopic images (Leica LD-60) of 1 to 2 mm thick (~1 cell) slices of the open cell foam were collected to compare cell shapes. Micro-computed tomography of~4 × 5 × 20 mm samples of closed cell foam was also undertaken, with volume renderings used to compare cell shapes (SkyScan 1172; 180 • rotation, image acquisition every 0.7 • , resolution <5 µm, volume depth 300 to 500 µm). load cell Figure 2), imparting 45 to 80% compression for respective 25 to 15 mm thick samples, with foam densification expected at ~80% compression [47,49,79]. Applied compression rates were 0.1, 1, 10, 50, 250, 1000, and 3250 mm/s, giving applied strain rates between ~0.05 and 200 s −1 . All samples were tested once at the lowest rate of 0.1 mm/s, then the sample from each group type with the median stress at 10% compression was selected for testing at the higher rates. The stiffer of the two anisotropic open cell foam samples was selected. The five selected samples were tested once at each of the higher rates, with at least 15 min between tests. For compression rates over 100 s −1 , the total displacement was as low as 40% of the intended displacement (of 12 mm) due to device safety features. Data logging frequency was 30 Hz for compression rates of 0.1 mm/s, 60 Hz for 1 mm/s, 1 kHz for 10 mm/s, and 5 kHz for 50 mm/s and above.

Compression Testing
Compression testing was parallel to the long cell axis of anisotropic (y-axis), and unconverted (z-axis) open cell foams, as these were the directions where the highest magnitudes of Poisson's ratio were expected [47,57,62]. The triaxial open cell foam was compressed in its z-axis. Samples were compressed by 12 mm (Bose ElectroForce 3200, 250 N load cell Figure 2), imparting 45 to 80% compression for respective 25 to 15 mm thick samples, with foam densification expected at~80% compression [47,49,79]. Applied compression rates were 0.1, 1, 10, 50, 250, 1000, and 3250 mm/s, giving applied strain rates between~0.05 and 200 s −1 . All samples were tested once at the lowest rate of 0.1 mm/s, then the sample from each group type with the median stress at 10% compression was selected for testing at the higher rates. The stiffer of the two anisotropic open cell foam samples was selected. The five selected samples were tested once at each of the higher rates, with at least 15 min between tests. For compression rates over 100 s −1 , the total displacement was as low as 40% of the intended displacement (of 12 mm) due to device safety features. Data logging frequency was 30 Hz for compression rates of 0.1 mm/s, 60 Hz for 1 mm/s, 1 kHz for 10 mm/s, and 5 kHz for 50 mm/s and above.
Surfaces were prepared with a speckle pattern (Halfords Matt Black or White Primer) to allow 2D DIC ( Figure 2). Tests were filmed (Proton, FASTCAM_SA3, 60K & Nikon, Nikkor 35 mm f/2D lens) at a frame rate that matched the sample rate of the test device, and with the camera's image plane parallel to the front face of the sample. Video footage was analysed (GOM Correlate, free 2D DIC software) to obtain lateral and axial engineering strains and strain rates in a target area (~5 mm high, 15 to 25 mm wide) in the centre of the samples (Figure 2a), avoiding the regions affected by contact with the compression plates [58].
Engineering stress vs. strain was calculated from test device force vs. displacement data, and sample dimensions. Values for Young's modulus (E z for unconverted and triaxial foams, and E y anisotropic foam) and Poisson's ratio (ν zx or ν yx as above) were obtained from the gradients of straight lines fitted to respective stress or lateral strain vs. axial strain between 0 and 2% compression, within the quasi-linear region for all foams.

Results
A summary of all data described below is in Supplementary Table S1. foam had re-entrant like cells (Figure 3c), as expected [47,58,71]. Also as expected [62,71], the unconverted closed cell foam had hexagonal cells with no visible cell rise direction (Figure 3d), and the triaxially converted closed cell foam had re-entrant like, kinked cell walls (Figure 3e) [62,71]. between 0 and 2% compression, within the quasi-linear region for all foams.

Results
A summary of all data described below is in Supplementary Table S1. The unconverted (UC) open cell foam had hexagonal shaped cells, elongated in the cell rise direction (z-axis, Figure 3a), as expected [47,58,71]. The anisotropic open cell foam had elongated cells in the stretched directions (y-axis, Figure 3b), and slightly inward angled, or re-entrant ribs, in the compressed x and z directions. The triaxially compressed open cell foam had re-entrant like cells (Figure 3c), as expected [47,58,71]. Also as expected [62,71], the unconverted closed cell foam had hexagonal cells with no visible cell rise direction (Figure 3d), and the triaxially converted closed cell foam had re-entrant like, kinked cell walls (Figure 3e) [62,71].

Poisson's Ratio
Auxetic foams exhibited NPR up to~2% compression for all applied strain rates (Figures 4 and 5, Supplementary Figure S1). Lateral strain mapping (x-axis) at 2% compression parallel to the y-axis shows the anisotropic open cell foam in predominantly lateral contraction (Figure 4a,b) at the lowest and highest applied strain rates. Axial strain was higher (~50%) within~2 mm of the compression plates than in the central region of the sample, where it was close to the applied value of 2% (Figure 4c,d); attributed to contact effects [58]. Measured maximum strain rates in the central region of the samples were, then, lower (80 s −1 ) than imposed values (200 s −1 , Supplementary Figure S1). Maximum measured strains were also lower (10 to 60%, Figure 4e,f and Supplementary Figure S1) than imposed values (40 to 80%), partly due to lower stiffness in the contact regions, but also due to a safety feature in the test device limiting the applied strain at higher strain rates.
(~50%) within ~2 mm of the compression plates than in the central region of the sample, where it was close to the applied value of 2% (Figure 4c,d); attributed to contact effects [58]. Measured maximum strain rates in the central region of the samples were, then, lower (80 s −1 ) than imposed values (200 s −1 , Supplementary Figure S1). Maximum measured strains were also lower (10 to 60%, Figure 4e,f and Supplementary Figure S1) than imposed values (40 to 80%), partly due to lower stiffness in the contact regions, but also due to a safety feature in the test device limiting the applied strain at higher strain rates.   (Figure 4e,f), so the differences in Poisson's ratio reported in Figure 5 are a good representation of the effect of strain rate. Standard deviations indicate differences between samples at the lowest strain rate were also relatively small (maximum standard error = 20% of mean Poisson's ratio, Figure 5). all other foams (open cell anisotropic, νyx = −2.02 ± 0.38 to −1.24; open cell triaxial, νzx = −0.35 ± 0.03 to −0.30; closed cell unconverted, νzx = 0.32 ± 0.03 to 0.18 and closed cell triaxial, νzx = −0.12 ± 0.01 to −0.06). These differences in Poisson's ratios with applied strain rates were similar across the lateral vs. axial strain range (Figure 4e,f), so the differences in Poisson's ratio reported in Figure 5 are a good representation of the effect of strain rate. Standard deviations indicate differences between samples at the lowest strain rate were also relatively small (maximum standard error = 20% of mean Poisson's ratio, Figure 5).

Young's Moduli
Increasing the applied strain rate from 0.005 to 200 s −1 approximately doubled Young's modulus in most cases ( Figure 6), but almost tripled the unconverted open cell foam's Young's modulus (Figure 6c), with values reported in supplementary Table S1. Both closed cell foams exhibited quasi-static Young's moduli of ~1 MPa (Figure 6d), as expected [62]. Increases in Young's modulus with applied strain rate were similar across the stress vs. strain (Figure 6a,b) and Young's modulus vs. strain rate relationships (Supplementary Figure S2). Standard deviations indicate differences between samples at the lowest strain rate were also relatively small (maximum standard error = 10% of mean Young's modulus, Figure 6c,d).  Table S1. Both closed cell foams exhibited quasi-static Young's moduli of~1 MPa (Figure 6d), as expected [62]. Increases in Young's modulus with applied strain rate were similar across the stress vs. strain (Figure 6a,b) and Young's modulus vs. strain rate relationships (Supplementary Figure S2). Standard deviations indicate differences between samples at the lowest strain rate were also relatively small (maximum standard error = 10% of mean Young's modulus, Figure 6c,d).

Discussion
Negative Poisson's ratio of auxetic foam was observed with full-field strain measurement at higher applied strain rates of up to 200 s −1 than in previous work [58,[68][69][70]. NPR was present at the highest strain rates, in agreement with previous tests at imposed rates

Discussion
Negative Poisson's ratio of auxetic foam was observed with full-field strain measurement at higher applied strain rates of up to 200 s −1 than in previous work [58,[68][69][70]. NPR was present at the highest strain rates, in agreement with previous tests at imposed rates of 10 s −1 [52] and impacts imparting variable strain rates of~100 s −1 [36], but approximately halved at the highest strain rate ( Figure 5). Established benefits to quasi-static indentation resistance from NPR [32,[41][42][43][44][45] may, then, apply during impacts of auxetic foams, but should be confirmed in further work. Measured strain rates (80 s −1 ) were lower than the maximum applied value of 200 s −1 , due to higher compression close to the plates (Figure 4c,d) than in the central region where Poisson's ratio was measured (Figure 4a,b). Obtained NPRs here were of higher magnitude (ν −0.1 to −2 Figure 5) than reported in previous studies measuring NPR quasi-statically and under impact (ν > −0.1 [36,52]), where strain rates were neither constant nor measured.
The anisotropic open cell foam exhibited high magnitude NPR below −1 (Figure 5a). Previous work on high aspect ratio (i.e., highly anisotropic) cell structures in foams also showed high anisotropy in mechanical properties; which typically have high Young's moduli and high magnitudes of Poisson's ratios parallel to the elongated cell axis [55,57,62]. Figure 3b shows the elongated cells along the y-axis (the stretched direction during conversion). Gibson and Ashby's flexure model [47], considering flexing of the slightly re-entrant long cell ribs (Figure 3b), would give higher strains along the perpendicular (lateral) x-or zaxes during compression or tension in the long cell y-axis, and hence high magnitude NPR.
Steam processed auxetic closed cell foam had quasi-static Poisson's ratio of −0.12 (Figure 5b) up to 2% compression. The quasi-static Young's modulus (~1 MPa, Figure 6d) of this auxetic closed cell foam was at the lower end of the reported range for foam in snow-sports back protectors (1 to 10 MPa [9,23]), football shin guards [6,66] and cricket thigh pads [5], to name a few. Young's modulus of the auxetic closed cell foam approximately doubled while NPR halved between minimum (0.005 s −1 ) and maximum strain rates (200 s −1 , Figure 6d). This doubling of Young's modulus as strain rate increased by 40,000 times is lower than the increase by a factor of five with increased strain rate of only 50 times reported for dilatant foam in soft-shell back protectors [9]. The linear relationship between Young's modulus and strain rate (Supplementary Figure S2) suggests the closed cell foams tested here were viscoelastic, rather than dilatant [20]. Recent work with the parent foam used here has produced higher magnitude anisotropic NPRs, approaching −1, in larger sheets of auxetic closed cell foam [62]. Further work could test whether such high magnitude NPR auxetic closed cell foam in isolation, or in combination with dilatant foam, could pass certification tests and ultimately enhance protection during sporting collisions and falls.
The sample sizes of 13 to 20 mm for closed cell and 20 to 25 mm for open cell foam, due to the various conversion methods, caused differences in applied strains (45 to 80%, Figure 4e,f) and strain rates (120 to 250 s −1 , Supplementary Figure S1) during compression testing. Sample sizes were otherwise accounted for in stress and strain calculations. The relative increase in strain rate (lowest to highest) was caused by differences in applied compression rate and so was the same between samples, despite the different sizes. We have demonstrated that NPR was maintained at the high strain rates expected under impact using 2D DIC, but NPR approximately halved in magnitude at the highest compression rates (Figures 4 and 5). Further work could use 3D DIC to confirm the Poisson's ratios measured here. Finite element modelling or digital volume correlation following high-speed micro-computed tomography [80] could also be applied to estimate or measure strain through the bulk of the foam. Impact testing auxetic closed cell foam, with similar stiffness (1 MPa, Figure 6d) to foam in sporting PPE [5,6,23,29], could show whether the established benefits of NPR to quasi-static indentation resistance (Equation (1) [32,[41][42][43][44][45]) and peak force under impact [34][35][36][37][38], inferred but not tested here, could improve sporting PPE. Further high-speed impact [81] and indentation testing could assess theoretical improvements by NPR. As the magnitude of NPR can decrease between quasi-static and high strain rate tests, high-speed indentation studies should focus on testing auxetic foam that has high magnitude quasi-static NPR (e.g., [42,54,[59][60][61]63,71]).

Conclusions
Poisson's ratios and Young's moduli were measured at low (0.005 s −1 ) and high (200 s −1 ) compressive strain rates, comparable to those imparted during impact tests for certifying sporting personal protective equipment. Negative Poisson's ratios at the highest strain rate were about half those measured quasi-statically, for both open and closed cell auxetic foams. Young's moduli typically doubled between the lowest and highest applied strain rates. This work indicates that NPR, and by extension NPR's known benefits to indentation resistance, are possible for auxetic foams during sporting impacts.