A Fast Calculation Method for Improving the Steering Arm of Mining Trucks with Macpherson Suspension

The steering arm has recently been frequently broken in a kind of mining truck with Macpherson suspension. To accelerate replacing the broken parts and minimize the economic cost, a fast calculation method for improving the steering arm is proposed in this paper. In this method, the forces on the steering arm are calculated by quasi-static analysis under a low vehicle velocity. Dynamic characteristics of the tire and road are partly included by considering the ranges of the rolling resistance coefficient and friction coefficient from the empirical values, which determines the torque on the steering arm under extreme conditions. The rigid–flexible coupling model for the left steering mechanism in ANSYS Workbench is established and solved to obtain the distribution stress on the steering arm under extreme conditions. Then, the reliability of the simulation results based on this fast calculation method is verified by the experiment. After determining an improvement scheme considering the economic and time cost, the satisfactory strength is obtained. The results illustrate that the strength of the improved steering arm has nearly doubled. Finally, the effectiveness of the improved steering arm is demonstrated by the users’ feedback after it is manufactured, installed, and used.


Introduction
Due to its simpler structure and lower manufacture/service cost, Macpherson suspension with the functions of vibration isolation and steering has been widely used in light mining trucks [1][2][3][4][5][6]. The steering arm is a key component in the steering mechanism integrated with Macpherson suspension, and its strength is very important for the security and reliability of the trucks. However, recently it has been frequently fractured in a kind of mining truck, which seriously threatened the driver's security and caused the damage to property.
Generally, a complete design process for a steering arm or other similar parts is as follows [7][8][9][10][11][12]. First, a full vehicle model, also called a virtual prototype model, is established based on multi-body dynamical software such as Adams, RecurDyn, SIMPACK, and so on. Second, forces on the steering arm are obtained under different roads and manipulation conditions, according to the established model. Third, the forces, particularly those under extreme conditions, will be used to optimize the geometry or shape of the steering arm considering the motion interference by using a professional finite element analysis (FEA) software, such as ANSYS and ABAQUS.
This digitized method, which shortens the design cycle and reduces the design cost, has been widely used, compared with the traditional method based on experiments. Surely, the full vehicle model should be comprehensively verified by experiments. However, it is not easy to accurately determine all parts' characteristics, particularly those of the tires and roads in surface mining, although the 3D geometric model of a mining truck can be established according to its engineering drawings. For example, when selected as a tire model in the Adams environment, PAC 2002 has up to 200 parameters that should be determined for a dynamic simulation [13][14][15]. For a tire that has not been completely measured by experiments, it is hardly possible to obtain these parameters, which causes a large difficulty in the dynamic simulation. In addition, determining the dynamical parameters of the full vehicle model and verifying its simulation results may spend much time on experiments, which reduces the efficiency of a new replacement part to some extent. Due to the complex characteristics of key parts, road surfaces, and tires, there are many design methods for the strength design, fatigue test, and life prediction of the steering arm according to the theoretical forces or accelerations [16][17][18][19]. In general, these methods did not consider the features of the vehicle, arrangement of each structure, and the assembly which may cause kinematic interference, and then the obtained results are often limited. In fact, the complete design method is beneficial to a company in the long run, but a fast and effective design will be the engineers' emphasis in the short term for the problem that only a few parts are broken in the vehicles. In this current stage, it is urgent to present a fast calculation method which can partly consider the characteristics of the road and tire for improving the steering arm.
Therefore, a fast calculation method for improving the steering arm of mining trucks with Macpherson suspension is proposed in this paper. This method can avoid establishing a full vehicle model and only analyse the left steering mechanism, increasing the efficiency of improving the steering arm. In this method, after the force analysis on the tire, the torque on the steering arm is calculated by using the empirical values of the rolling resistance coefficient and friction coefficient allowed to be limited in the two ranges; the rigid-flexible coupling model for the left steering mechanism in ANSYS environment is established and solved to obtain the distribution stress on the steering arm under extreme conditions. Then, the stress test is carried out to verify the reliability of the simulation results based on the fast method. Finally, an improvement scheme with a low economic and time cost is presented, and its effectiveness is demonstrated by the users' feedback after it was run for a period of time. Additionally, this paper's framework is shown in Figure 1. · Analyze the force on the tire. · Obtain the torque on the steering arm under the extreme condition.
· Establish the rigid-flexible coupling model for the left steering mechanism. · Obtain the stress distribution on the steering arm.
· Analyze the reason of the failure on the steering arm · Provide the improvement schemes based on the stress distribution on the steering arm. · Discuss these improvements' advantages and disadvantages. · Determine a final improvement for steering arm, considering the economic and time cost. · Draw the conclusions. Section 7 · Carry out the experiment, and obtain the actual stress distribution on steering arm. · Verify the simulation results by comparing the experiment results.   Figure 2 shows the installation and geometry of the steering arm in the Macpherson suspension system, which includes many parts, such as the A-type frame, hydro-pneumatic strut, tie rod, tire, and so on. The steering arm, whose role is to transmit steering torque, is a key part in the Macpherson suspension system integrated into the steering mechanism. The king-pin axis is just the axis of the hydro-pneumatic strut in the Macpherson suspension [20,21]. Steering torque is generated by the force from the steering cylinder around the king-pin axis. On the contrary, torque-generated by the forces from the road around the king-pin axis-will act on the steering arm when the truck drives on the road.

Failure Analysis
The fractured steering arm is shown in Figure 3. In a kind of mining truck, its arm is broken frequently, particularly when it drives through a high obstacle acco the drivers' feedback. It is observed that, unlike fatigue failure, the fracture area an evident crack propagation happened abruptly. In addition, the fracture area ha plastic deformation. On the one hand, according to the characteristics of the frac cause of failure can be basically determined by the long experience of engineers other hand, the designed load capacity is 60 t for the kind of truck, while the reaches 80 t due to the complex transportation requirement; the reason that the p broken is the lack strength to a large extent. In addition, the structure of the stee is not reasonable. It not only produces a bending movement, but also torsion at of the steering arm, which reduces the strength of this parts. At present, many tr gradually phased out of this structural form, and scheme 1, shown in Section 6 creasingly adopted. Therefore, the reason that the steering arm fractured is most strength shortage.

Failure Analysis
The fractured steering arm is shown in Figure 3. In a kind of mining truck, its steering arm is broken frequently, particularly when it drives through a high obstacle according to the drivers' feedback. It is observed that, unlike fatigue failure, the fracture area without an evident crack propagation happened abruptly. In addition, the fracture area has certain plastic deformation. On the one hand, according to the characteristics of the fracture, the cause of failure can be basically determined by the long experience of engineers. On the other hand, the designed load capacity is 60 t for the kind of truck, while the real load reaches 80 t due to the complex transportation requirement; the reason that the parts have broken is the lack strength to a large extent. In addition, the structure of the steering arm is not reasonable. It not only produces a bending movement, but also torsion at the root of the steering arm, which reduces the strength of this parts. At present, many trucks are gradually phased out of this structural form, and scheme 1, shown in Section 6.1, is increasingly adopted. Therefore, the reason that the steering arm fractured is most likely its strength shortage. reaches 80 t due to the complex transportation requirement; the reason that the parts have broken is the lack strength to a large extent. In addition, the structure of the steering arm is not reasonable. It not only produces a bending movement, but also torsion at the root of the steering arm, which reduces the strength of this parts. At present, many trucks are gradually phased out of this structural form, and scheme 1, shown in Section 6.1, is increasingly adopted. Therefore, the reason that the steering arm fractured is most likely its strength shortage.

Force Analysis and Torque Calculation
All the forces of the vehicle come from the road surface, not considering the aerodynamic resistance. When the steering arm is broken, due to kinematic restrictions, the steering arm will inevitably rotate along the king-pin axis. It is known that the steering arm mainly withstands the torque generated by the forces from the road around the king-pin axis, because the horizontal and vertical forces will be respectively occupied by the A-type frame and hydro-pneumatic strut according to the characteristics and the previous kinematic analysis of Macpherson suspension. Accordingly, the key is to determine the torque, particularly the maximum one on the steering arm from the road under the condition described by the drivers when it is broken. Figure 4 shows the force analysis on the tire installed in the driven wheel when a truck with rear-wheel drive travels through an obstacle. In this figure, F d , F z , F f , and F N are the driving force, vertical force from the sprung mass, friction, and reaction force from the road, respectively, M R represents the rolling resistance moment, and h and R respectively represent the height of the obstacle and the radius of the tire.

Force Analysis on the Tire
Appl. Sci. 2021, 11, x FOR PEER REVIEW 5

Force Analysis and Torque Calculation
All the forces of the vehicle come from the road surface, not considering the aer namic resistance. When the steering arm is broken, due to kinematic restrictions, the s ing arm will inevitably rotate along the king-pin axis. It is known that the steering mainly withstands the torque generated by the forces from the road around the kin axis, because the horizontal and vertical forces will be respectively occupied by the A frame and hydro-pneumatic strut according to the characteristics and the previous matic analysis of Macpherson suspension. Accordingly, the key is to determine the to particularly the maximum one on the steering arm from the road under the conditio scribed by the drivers when it is broken. Figure 4 shows the force analysis on the tire installed in the driven wheel wh truck with rear-wheel drive travels through an obstacle. In this figure, Fd, Fz, Ff, and F the driving force, vertical force from the sprung mass, friction, and reaction force from road, respectively, MR represents the rolling resistance moment, and h and R respect represent the height of the obstacle and the radius of the tire. When a truck needs to pass through a higher obstacle, its speed is generally very It is assumed that the truck drives through the obstacle at a low constant speed, an equilibrium equations can be expressed as  When a truck needs to pass through a higher obstacle, its speed is generally very low. It is assumed that the truck drives through the obstacle at a low constant speed, and the equilibrium equations can be expressed as

Force Analysis on the Tire
where θ = arcsin R−h R and f r is the rolling resistance coefficient. Based on the concept of the friction cycle [13,22], the maximum lateral force can be calculated as where µ is the tire-road friction coefficient. It is noted that there is a residual torque acting on the steering arm, only when the opposite one caused by the lateral friction around the king-pin axis is less than the one generated by the F d and king-pin axis. Therefore, the residual torque can be written as where L 1 and L 2 respectively represent the arm lengths of the longitudinal and lateral forces along the king-pin axis, and they both can be measured by the 3D model of the Macpherson suspension system integrated into the steering mechanism. In addition, the energy of the stress responses, as shown in the experiment results in this paper, mainly focuses on a very low frequency due to the truck with a low velocity when it drives through a high obstacle, so the tire fore modelling, notwithstanding similar to the static analysis (i.e., quasi-static analysis), is reasonable. Table 1 shows the parameters of the truck for calculating the torque on the steering arm. Although the rolling resistance coefficient and friction coefficient can be determined based on the experiential values for the unsurfaced road recommended by the literature [23,24], they are two ranges as shown in Table 1. The two ranges can moderately reflect the dynamic characteristics of the road and the tire. h can be obtained by measuring the height of the obstacle where the steering arm is broken frequently. According to Equations (1) to (5) and Table 1, torque M on the steering arm with different rolling resistance and friction coefficients can be obtained, as shown in Figure 5. The torque value is mainly determined according to three parameters-the height of the obstacle, the coefficient of friction, and the coefficient of rolling resistance. The height of the obstacle can be obtained by measuring the height of the road surface at the frequently broken site, while the other two parameters are related to the state of the vehicle, the characteristics of the road surface and the characteristics of the tire. In order to avoid obtaining the complex characteristics of the road and tire, we can determine the maximum torque according to the range of its experience values, so as to ensure a certain strength redundancy. These coefficients are confined in the ranges given in Table 1. Similarly, the relationship between the torque on the steering arm and the height of the obstacle is shown in Figure 6 where parameters L1 and L2 will vary with the height of the obstacle, rolling resistance coefficient fr and friction coefficient μ are, respectively, 0.15 and 0.4, and the others remain unchanged as shown in Table 1. It can be seen that the higher the obstacle is, the greater the torque on the steering arm becomes. For safety's sake, the maximum torque will be used to verify and improve the steering arm, and the maximum is 16.52 kNm under the extreme conditions where the steering arm is broken frequently.  Figure 7 shows the left steering mechanism, which is simplified as the following main parts: the steering arm, base of the steering arm, assembled tie rod, assembled steering cylinder, and four ball pins. To carry out the strength analysis, a rigid-flexible coupling model is established by importing the 3D geometric model of the mechanism into the AN-SYS environment. The stress distributions of these parts can be obtained by solving the model in ANSYS Workbench, after defining the material properties, connected relations between parts, element types, meshes, and loads. Similarly, the relationship between the torque on the steering arm and the height of the obstacle is shown in Figure 6 where parameters L 1 and L 2 will vary with the height of the obstacle, rolling resistance coefficient f r and friction coefficient µ are, respectively, 0.15 and 0.4, and the others remain unchanged as shown in Table 1. It can be seen that the higher the obstacle is, the greater the torque on the steering arm becomes. For safety's sake, the maximum torque will be used to verify and improve the steering arm, and the maximum is 16.52 kN m under the extreme conditions where the steering arm is broken frequently. Similarly, the relationship between the torque on the steering arm and the height of the obstacle is shown in Figure 6 where parameters L1 and L2 will vary with the height of the obstacle, rolling resistance coefficient fr and friction coefficient μ are, respectively, 0.15 and 0.4, and the others remain unchanged as shown in Table 1. It can be seen that the higher the obstacle is, the greater the torque on the steering arm becomes. For safety's sake, the maximum torque will be used to verify and improve the steering arm, and the maximum is 16.52 kNm under the extreme conditions where the steering arm is broken frequently.  Figure 7 shows the left steering mechanism, which is simplified as the following main parts: the steering arm, base of the steering arm, assembled tie rod, assembled steering cylinder, and four ball pins. To carry out the strength analysis, a rigid-flexible coupling model is established by importing the 3D geometric model of the mechanism into the AN-SYS environment. The stress distributions of these parts can be obtained by solving the model in ANSYS Workbench, after defining the material properties, connected relations between parts, element types, meshes, and loads.   Figure 7 shows the left steering mechanism, which is simplified as the following main parts: the steering arm, base of the steering arm, assembled tie rod, assembled steering cylinder, and four ball pins. To carry out the strength analysis, a rigid-flexible coupling model is established by importing the 3D geometric model of the mechanism into the ANSYS environment. The stress distributions of these parts can be obtained by solving the model in ANSYS Workbench, after defining the material properties, connected relations between parts, element types, meshes, and loads. Appl. Sci. 2021, 11, x FOR PEER REVIEW 8 of 18 The steering arm is the emphasis in this paper, and its material property is shown in Table 2.

Rigid-Flexible Coupling Model
The rigid-flexible coupling model is shown in Figure 8, and the modelling steps are mainly as follows.
(1) Define rigid and elastic bodies. Since the deformation of the four ball is small, and the base of the steering arm mainly is to define a king-pin coordinate whose Z axis is the king-pin axis, as shown in Figure 7, the five parts are defined as rigid body, but the others as elastic body.
(2) Define connection relations. The connection relations between the two ball pins in the left side and the steering arm are defined as the bonded contact, and they respectively connect with the assembled steering cylinder and tie rod by spherical joint. Similarly, the other ball pins respectively connect with the assembled steering cylinder and tie rod by spherical joint.
(3) Perform the meshing. The tetrahedral and hexahedral meshes will be used for all the elastic bodies, and the high stress area in the steering arm will be further refined. Compared with the steering arm emphasized in this paper, the meshes of other parts is relatively coarser, as shown in Figure 8.
(4) Determine the constraints and loads. The steering arm with one degree of freedom can rotate around the king-pin axis by defining a remote displacement, and the torque on it is 16.52 kNm which is obtained by the quasi-static analysis mentioned in Section 3 under extreme conditions. The two ball pins in the right side are fixed. The steering arm is the emphasis in this paper, and its material property is shown in Table 2.

Rigid-Flexible Coupling Model
The rigid-flexible coupling model is shown in Figure 8, and the modelling steps are mainly as follows.

Stress Distribution on the Steering Arm
Solving the rigid-flexible coupling model can obtain the stress distribution on the steering arm, as shown in Figure 9. It is seen that the high-stress area is consistent with that of the fractured steering arm, and the maximal Von Mises stress is 336.77 MPa, which has markedly excessed its yield strength from Table 2. On the one hand, the fast calculation neglects the horizontal and vertical forces on the steering arm, and on the other hand, it did not completely consider the complex dynamic characteristics of the tire and road, which illustrates that the real stress may be more than 336.77 MPa. As a frequently moving part, therefore, the steering arm indeed has a great risk of failure, because the maximum stress has markedly exceeded its yield strength under the quasi-static analysis. (1) Define rigid and elastic bodies. Since the deformation of the four ball is small, and the base of the steering arm mainly is to define a king-pin coordinate whose Z axis is the king-pin axis, as shown in Figure 7, the five parts are defined as rigid body, but the others as elastic body.
(2) Define connection relations. The connection relations between the two ball pins in the left side and the steering arm are defined as the bonded contact, and they respectively connect with the assembled steering cylinder and tie rod by spherical joint. Similarly, the other ball pins respectively connect with the assembled steering cylinder and tie rod by spherical joint.
(3) Perform the meshing. The tetrahedral and hexahedral meshes will be used for all the elastic bodies, and the high stress area in the steering arm will be further refined. Compared with the steering arm emphasized in this paper, the meshes of other parts is relatively coarser, as shown in Figure 8.
(4) Determine the constraints and loads. The steering arm with one degree of freedom can rotate around the king-pin axis by defining a remote displacement, and the torque on it is 16.52 kN m which is obtained by the quasi-static analysis mentioned in Section 3 under extreme conditions. The two ball pins in the right side are fixed.

Stress Distribution on the Steering Arm
Solving the rigid-flexible coupling model can obtain the stress distribution on the steering arm, as shown in Figure 9. It is seen that the high-stress area is consistent with that of the fractured steering arm, and the maximal Von Mises stress is 336.77 MPa, which has markedly excessed its yield strength from Table 2. On the one hand, the fast calculation neglects the horizontal and vertical forces on the steering arm, and on the other hand, it did not completely consider the complex dynamic characteristics of the tire and road, which illustrates that the real stress may be more than 336.77 MPa. As a frequently moving part, therefore, the steering arm indeed has a great risk of failure, because the maximum stress has markedly exceeded its yield strength under the quasi-static analysis.

Stress Distribution on the Steering Arm
Solving the rigid-flexible coupling model can obtain the stress distribution on th steering arm, as shown in Figure 9. It is seen that the high-stress area is consistent wit that of the fractured steering arm, and the maximal Von Mises stress is 336.77 MPa, whic has markedly excessed its yield strength from Table 2. On the one hand, the fas calculation neglects the horizontal and vertical forces on the steering arm, and on the othe hand, it did not completely consider the complex dynamic characteristics of the tire an road, which illustrates that the real stress may be more than 336.77 MPa. As a frequentl moving part, therefore, the steering arm indeed has a great risk of failure, because th maximum stress has markedly exceeded its yield strength under the quasi-static analysi

Test Arrangement
On the one hand, the stress test is performed to understand the forces on parts an realize a better design for mining trucks. On the other hand, the stress test can verify th modelling results from the fast calculation method for the steering arm. The stress point and the test road in the experiment are shown in Figures 10 and 11, respectively. Differen test points on parts, such as the steering arm, assembled steering cylinder, and assemble tie rod, are arranged. These points include three-and single-axis strain gauges, and ther are, in total, 35 channels. In the test road, the height of the obstacle is arranged as 200 mm

Test Arrangement
On the one hand, the stress test is performed to understand the forces on parts and realize a better design for mining trucks. On the other hand, the stress test can verify the modelling results from the fast calculation method for the steering arm. The stress points and the test road in the experiment are shown in Figures 10 and 11, respectively. Different test points on parts, such as the steering arm, assembled steering cylinder, and assembled tie rod, are arranged. These points include three-and single-axis strain gauges, and there are, in total, 35 channels. In the test road, the height of the obstacle is arranged as 200 mm, and it is lower than the extreme condition, which can ensure driving safety. It is not easy to paste the strain rosette on the account of the curved surface in the high stress area, so the test points with a three-axis rectangular rosette on the steering arm are shown Figure 12. and it is lower than the extreme condition, which can ensure driving safety. It is not easy to paste the strain rosette on the account of the curved surface in the high stress area, so the test points with a three-axis rectangular rosette on the steering arm are shown Figure 12.     and it is lower than the extreme condition, which can ensure driving safety. It is not easy to paste the strain rosette on the account of the curved surface in the high stress area, so the test points with a three-axis rectangular rosette on the steering arm are shown Figure 12.    and it is lower than the extreme condition, which can ensure driving safety. It is not easy to paste the strain rosette on the account of the curved surface in the high stress area, so the test points with a three-axis rectangular rosette on the steering arm are shown Figure 12.

Strain Results from the Test
The strain responses on the steering arm are shown in Figure 13 where the superscript and subscript respectively represent the serial number of the test points and the direction of the three-axis strain gages, for example, ε 1 45 .

Strain Results from the Test
The strain responses on the steering arm are shown in Figure 13 where the superscript and subscript respectively represent the serial number of the test points and the direction of the three-axis strain gages, for example, 1 45  . Figure 13. Strain responses on the steering arm.

Stress Results from the Test
According to the strain responses, the principal stress and its direction can be calculated by the following formulas [25,26]: By (6), the maximum principal stress on test points 1 and 2 can be obtained, as shown in Figure 14. According to the fast Fourier transform, the amplitudes of the maximum principal stress on test points 1 and 2 can be obtained, as shown in Figure 15. It is noted that for clarity, the two curves are not completely shown in Figure 15, due to the small amplitudes corresponding to the frequencies which are more than 1 Hz. Figure 13. Strain responses on the steering arm.

Stress Results from the Test
According to the strain responses, the principal stress and its direction can be calculated by the following formulas [25,26]: By (6), the maximum principal stress on test points 1 and 2 can be obtained, as shown in Figure 14. According to the fast Fourier transform, the amplitudes of the maximum principal stress on test points 1 and 2 can be obtained, as shown in Figure 15. It is noted that for clarity, the two curves are not completely shown in Figure 15, due to the small amplitudes corresponding to the frequencies which are more than 1 Hz.     Figure 14 shows the stresses varying with time, so it is not convenient to compare them with the simulation. Accordingly, the statistics for these stresses can be obtained, as shown in Table 3.

Stress Results from the Simulation
For comparison, the torque in the rigid-flexible coupling model is set to 11.345 kNm-the value corresponding to the height 200 mm of the obstacle which is the same Figure 15. Amplitude spectra of the maximum principal stress on test points 1 and 2. Figure 14 shows the stresses varying with time, so it is not convenient to compare them with the simulation. Accordingly, the statistics for these stresses can be obtained, as shown in Table 3.

Stress Results from the Simulation
For comparison, the torque in the rigid-flexible coupling model is set to 11.345 kN·mthe value corresponding to the height 200 mm of the obstacle which is the same with the test road; after this model is solved, the stress distribution of the maximum principal stress is shown in Figure 16. By postprocessing, it can be determined that the maximum principal stresses on test points 1 and 2 are about 12 and 190 MPa, respectively.
Appl. Sci. 2021, 11, x FOR PEER REVIEW 13 of 18 with the test road; after this model is solved, the stress distribution of the maximum principal stress is shown in Figure 16. By postprocessing, it can be determined that the maximum principal stresses on test points 1 and 2 are about 12 and 190 MPa, respectively.

Discussions
It can be seen the stress distribution simulated by FEA are basically the same with the experiment on test points 1 and 2, by comparing the maximum principal stresses from the test (see the RMS shown in Table 3) and the simulation (see Section 5.4). Although Figure 16. Stress distribution of the maximum principal stress on the steering arm.

Discussions
It can be seen the stress distribution simulated by FEA are basically the same with the experiment on test points 1 and 2, by comparing the maximum principal stresses from the test (see the RMS shown in Table 3) and the simulation (see Section 5.4). Although there are some deviations, their relative errors are both not more than 15%, which satisfies the requirement in engineering. Since the speed of the truck is generally very small when passing a high obstacle, it can be regarded as a quasi-static dynamic model. In addition, it can be seen from the experiment in Figure 15 that the energy of the stress responses mainly focuses on a very low frequency due to the truck with a low velocity when it drives a high obstacle, so the simulation results, notwithstanding similar to the static analysis, are feasible.
From the above discussions, it can be concluded that the simulation results by the fast calculation method proposed in this paper are feasible and reliable. The next section will use the simulation method to improve the steering arm.

Improvement Analysis
The steering arm is generally made of castings or forgings, with the casting round corners, bosses, pits, cone holes, bolt holes, counter bores, and so on, and its shape is irregular, as shown Figure 7. According to the stress distribution on the steering arm, its failure is from the combined effect by the bending and twisting. Based on the premise of no motion interference between the steering arm with other parts, three improvement schemes can be used to enhance its strength, as shown in Figures 17 and 18. These schemes have respective advantages and disadvantages, and their descriptions and discussions are as follows.
Appl. Sci. 2021, 11, x FOR PEER REVIEW 14 of 1 as shown in Figure 17. No matter which role⎯withstanding the tire force or performin the steering-reducing the torsion is beneficial. However, the scheme will result in th modification of the ball pin and even the base of the steering arm.
(2) Improvement scheme 2. The scheme increasing the thickness is to augment th moment of inertia of the cross-sectional area about the Z axis, as well as the polar momen of inertia about the X axis, as shown in Figure 18. However, the enhanced strength base on the scheme is not as evident as augmenting the width (i.e., improvement scheme 3 according to the qualitative analysis from mechanics of materials [27]. In addition, th scheme will similarly result in the modification of the ball pin, or even a change in positio of the spherical joint, and the change may have an adverse effect on the kinematic chara teristics. (3) Improvement scheme 3. The scheme, whose purpose is the same as the improve ment scheme 2, is to increase the width, as shown in Figure 18. However, the kinemat analysis should be conducted to avoid motion interference between the improved steerin arm and other parts.   Having a big modification in the steering system, schemes 1 and 2 may be not very applicable in this stage, for the steering arm needs to be replaced fast, but they can be adopted for the development of new vehicle in the near future. To sum up, improvement scheme 3 will be used to enhance the strength of the steering arm in this paper.

Improved Steering Arm
The steering arm has been repeatedly modified to maximize its strength and to avoid the stress concentration and motion interference, and the final improvement is shown in Figure 19. After the steering arm in the rigid-flexible coupling model mentioned in Section 4.2 is replaced by the improved one, the Von Mises stress distribution can be obtained by solving the model, as shown in Figure 19. It can be seen that the maximum Von Mises stress 176.25 MPa is located in the contact area between the steering arm and the ball pin, and the maximum stress on its original high stress area has decreased to around 85 MPa. By comparing the maximum Von Mises stresses on the steering arm improved before and after, it can be seen that the strength of the improved steering arm has nearly doubled. Furthermore, the enhancement in rigidity apparently decreases the stress on the contact area between the steering arm and the ball pin away from fixed end, which satisfies the real condition. The results illustrate that the improved steering arm has a significant enhancement in strength under the extreme conditions (i.e., obstacle's height 300 mm).
Then, the improved steering arm is manufactured and installed for the kind of mining truck, and the real product is shown in Figure 20. According to the feedback from the users, there is no fracture of the improved steering arm after it was installed, which illustrates that the issue has been addressed. At present, the improved part has been used for more than half a year without any fault, demonstrating that the current scheme is effective, and the rapid improvement and optimization of the steering arm has been realized. (1) Improvement scheme 1. The scheme is to alleviate the torsional effect around the X axis by adjusting the position of the spherical joint of the ball pin on the steering arm, as shown in Figure 17. No matter which role-withstanding the tire force or performing the steering-reducing the torsion is beneficial. However, the scheme will result in the modification of the ball pin and even the base of the steering arm.
(2) Improvement scheme 2. The scheme increasing the thickness is to augment the moment of inertia of the cross-sectional area about the Z axis, as well as the polar moment of inertia about the X axis, as shown in Figure 18. However, the enhanced strength based on the scheme is not as evident as augmenting the width (i.e., improvement scheme 3), according to the qualitative analysis from mechanics of materials [27]. In addition, the scheme will similarly result in the modification of the ball pin, or even a change in position of the spherical joint, and the change may have an adverse effect on the kinematic characteristics.
(3) Improvement scheme 3. The scheme, whose purpose is the same as the improvement scheme 2, is to increase the width, as shown in Figure 18. However, the kinematic analysis should be conducted to avoid motion interference between the improved steering arm and other parts.
Having a big modification in the steering system, schemes 1 and 2 may be not very applicable in this stage, for the steering arm needs to be replaced fast, but they can be adopted for the development of new vehicle in the near future. To sum up, improvement scheme 3 will be used to enhance the strength of the steering arm in this paper.

Improved Steering Arm
The steering arm has been repeatedly modified to maximize its strength and to avoid the stress concentration and motion interference, and the final improvement is shown in Figure 19. After the steering arm in the rigid-flexible coupling model mentioned in Section 4.2 is replaced by the improved one, the Von Mises stress distribution can be obtained by solving the model, as shown in Figure 19. It can be seen that the maximum Von Mises stress 176.25 MPa is located in the contact area between the steering arm and the ball pin, and the maximum stress on its original high stress area has decreased to around 85 MPa. By comparing the maximum Von Mises stresses on the steering arm improved before and after, it can be seen that the strength of the improved steering arm has nearly doubled. Furthermore, the enhancement in rigidity apparently decreases the stress on the contact area between the steering arm and the ball pin away from fixed end, which satisfies the real condition. The results illustrate that the improved steering arm has a significant enhancement in strength under the extreme conditions (i.e., obstacle's height 300 mm).

Conclusions
This paper proposes a fast calculation method for improving the steering arm, addressing the issue that it is frequently broken in a kind of mining truck with Macpherson suspension. In the method, stress distribution on the steering arm is obtained by analyzing the force on the tire, calculating the torque on the steering arm, and establishing and solving the rigid-flexible coupling model of the left steering mechanism. The obtained stress results are used to improve the steering arm. The improvement results by using the the fast calculation method illustrate that the strength of the improved steering arm has nearly doubled. The experiment results and the users' feedback further demonstrate the feasibility and effectiveness of this method.
Most importantly, this method is based on the empirical values of the rolling resistance coefficient and friction coefficient in calculating the torque on the steering arm, and these coefficients are respectively in the two ranges which can partly consider the dynamic characteristics of the tire and road. This handling way can avoid establishing a full vehicle model and only study the left steering mechanism by a static analysis, increasing the efficiency of improving the steering arm.
In fact, the improvement based on the fast calculation method is temporary to rapidly solve the current problem, so that the damaged truck can be put into use as soon as possible. This approach depends largely on the level of engineering experience. It is worth noting that this analytical method agrees well with the experimental results; even the stress distribution is in good agreement. At present, the improved parts have been used for more than half a year without any fault, indicating that the current scheme is effective, and the rapid improvement and optimization of the steering arm has been realized. On the one hand, the experimental results show the correctness of the fast calculation results. On the other hand, the feedback also shows the effectiveness of the improved results, after Then, the improved steering arm is manufactured and installed for the kind of mining truck, and the real product is shown in Figure 20. According to the feedback from the users, there is no fracture of the improved steering arm after it was installed, which illustrates that the issue has been addressed. At present, the improved part has been used for more than half a year without any fault, demonstrating that the current scheme is effective, and the rapid improvement and optimization of the steering arm has been realized.

Conclusions
This paper proposes a fast calculation method for improving the steering arm, addressing the issue that it is frequently broken in a kind of mining truck with Macpherson suspension. In the method, stress distribution on the steering arm is obtained by analyzing the force on the tire, calculating the torque on the steering arm, and establishing and solving the rigid-flexible coupling model of the left steering mechanism. The obtained stress results are used to improve the steering arm. The improvement results by using the the fast calculation method illustrate that the strength of the improved steering arm has nearly doubled. The experiment results and the users' feedback further demonstrate the feasibility and effectiveness of this method.
Most importantly, this method is based on the empirical values of the rolling resistance coefficient and friction coefficient in calculating the torque on the steering arm, and these coefficients are respectively in the two ranges which can partly consider the dynamic characteristics of the tire and road. This handling way can avoid establishing a full vehicle model and only study the left steering mechanism by a static analysis, increasing the efficiency of improving the steering arm.
In fact, the improvement based on the fast calculation method is temporary to rapidly solve the current problem, so that the damaged truck can be put into use as soon as possible. This approach depends largely on the level of engineering experience. It is worth

Conclusions
This paper proposes a fast calculation method for improving the steering arm, addressing the issue that it is frequently broken in a kind of mining truck with Macpherson suspension. In the method, stress distribution on the steering arm is obtained by analyzing the force on the tire, calculating the torque on the steering arm, and establishing and solving the rigid-flexible coupling model of the left steering mechanism. The obtained stress results are used to improve the steering arm. The improvement results by using the the fast calculation method illustrate that the strength of the improved steering arm has nearly doubled. The experiment results and the users' feedback further demonstrate the feasibility and effectiveness of this method.
Most importantly, this method is based on the empirical values of the rolling resistance coefficient and friction coefficient in calculating the torque on the steering arm, and these coefficients are respectively in the two ranges which can partly consider the dynamic characteristics of the tire and road. This handling way can avoid establishing a full vehicle model and only study the left steering mechanism by a static analysis, increasing the efficiency of improving the steering arm.
In fact, the improvement based on the fast calculation method is temporary to rapidly solve the current problem, so that the damaged truck can be put into use as soon as possible. This approach depends largely on the level of engineering experience. It is worth noting that this analytical method agrees well with the experimental results; even the stress distribution is in good agreement. At present, the improved parts have been used for more than half a year without any fault, indicating that the current scheme is effective, and the rapid improvement and optimization of the steering arm has been realized. On the one hand, the experimental results show the correctness of the fast calculation results. On the other hand, the feedback also shows the effectiveness of the improved results, after the improved steering arm is installed into the mining dump truck and run for a period of time. It is sure that the method can provide a reference for the similar parts or mechanisms so as to realize their fast improvement and design.