An Equivalent Radial Stiffness Method of Laboratory SEPT on Anchorage Performance Prediction of Rockbolts under Different Field Geoconditions

: The short encapsulation pull-out test (SEPT) is extensively used in rockbolting research or engineering. The ﬁeld SEPT is time-consuming and labor-intensive, and its result is only applicable to the tested in situ. The laboratory SEPT is usually employed in theoretical rockbolting research due to its easily controlled variables. However, the design of laboratory SEPT is quite different, as there is no standard testing method, resulting in the applicability and limitations of each study not being clear. Accordingly, the aim of this paper is to bridge the gap between laboratory SEPT research and ﬁeld application. On the basis of thick-walled cylinder theory, a mechanical model of a rock bolt subjected to axial load was established under consideration of the deformational behavior of conﬁning materials around the bolt. Plane stress analysis was introduced to derive the analytical relationship between the axial force of the bolt and the deformation of the conﬁning materials. A new approach of laboratory SEPT sample design was established, namely, equivalent radial stiffness theory, to simulate anchorage performance in a speciﬁc in-situ geocondition. Consequently, the ﬁeld SETP could be replaced by laboratory testing using properly designed bolting samples with a certain level of accuracy. In addition, the application scope of previous laboratory SEPT research could be accurately deﬁned. Laboratory SEPT was carried out to study the anchoring performance of right spiral rebar bolts under different conﬁning materials. Poly Vinyl Chloride (PVC) tubes with a thickness of 31 mm, #60 aluminum (Al) tubes with a thickness of 5.8 mm, and #20 steel tubes with a thickness of 5.5, 7.0 mm were used in sample preparation to simulate soft, medium, and hard surrounding rocks in the ﬁeld. The anchorage performance of the bolt under different geoconditions was systematically proposed, which provides a technical approach for similar research using different anchoring materials. A negative exponential expression formulating the axial load capacity of the right spiral bolts for the full spectrum of the surrounding rocks’ strength was derived on the basis of theoretical analysis and data regression. It can be used for preliminary reinforcement design, as well as the accurate key parameter setting in the numerical calculation of roadway deformation using right spiral bolts. The theoretical prediction is highly consistent with the testing results in the literature, which conﬁrms the validity and reliability of this research. This study contributes to the establishment of a laboratory SEPT standard in rock mechanics. weak surrounding rock ( E r = 1.0–3.5 GPa, v r = 0.25–0.30). The radial stiffness of the #6061 Al ( E = 68.9 GPa and v = 0.33) tube corresponds to the medium-strong surrounding rock ( E r = 15–50 GPa, v r = 0.20–0.25). The radial stiffness of the #20 steel ( E = 206 GPa and v = 0.3) tube corresponds to the strong surrounding rock ( E r = 50–140 GPa, v r = 0.15–0.20).


Introduction
Rockbolts have been used to provide ground support in mines for more than one century [1][2][3][4][5]. Rockbolts are characterized by highly effective reinforcement and simple be developed to realize anchorage performance in laboratory testing to be similar to its field behavior.
On the basis of thick-walled cylinder theory, this study establishes the relationship between laboratory SEPT sample confinement with the mechanical properties of rock mass. On the basis of the equivalent radial stiffness principle, laboratory SEPT was designed using PVC, #6061 Al, and #20 steel as confining material of the specimens to simulate the different strengths of rock mass. The anchorage performance of the dextral bolt, which is one kind of the two most commonly used rock bolts in the underground coal-mine industry in China, was investigated under different field geoconditions. The relationship between the axial loading capacity of the bolt and the elastic properties of the surrounding rock was obtained via theoretical analysis, which provides a theoretical basis for anchorageperformance prediction in dextral-bolt support design and accurate parameters for related numerical modeling.

Equivalent Radial Stiffness Theory
Yazici and Kaiser introduced the plane strain analysis of thick-walled cylinder theory to the study of rockbolting mechanics [34]. Hyett et al. further applied this method to investigate the stress distribution of the bolt subjected to axial loading and established a framework of rockbolting in field conditions, a theoretical model, and corresponding laboratory configuration (Figure 1) [35]. For laboratory testing to reflect the real situation, a confining tube with the same radial stiffness to the surrounding rock should be selected to prepare the testing sample. that laboratory SEPT results represent actual anchorage performance, geoco insitu should be considered in the experimental design. Theory and technology developed to realize anchorage performance in laboratory testing to be similar to behavior.
On the basis of thick-walled cylinder theory, this study establishes the rela between laboratory SEPT sample confinement with the mechanical properties mass. On the basis of the equivalent radial stiffness principle, laboratory SEPT signed using PVC, #6061 Al, and #20 steel as confining material of the specimens late the different strengths of rock mass. The anchorage performance of the dex which is one kind of the two most commonly used rock bolts in the undergrou mine industry in China, was investigated under different field geoconditions. tionship between the axial loading capacity of the bolt and the elastic properti surrounding rock was obtained via theoretical analysis, which provides a theoret for anchorage-performance prediction in dextral-bolt support design and accurat eters for related numerical modeling.

Equivalent Radial Stiffness Theory
Yazici and Kaiser introduced the plane strain analysis of thick-walled cylind to the study of rockbolting mechanics [34]. Hyett et al. further applied this meth vestigate the stress distribution of the bolt subjected to axial loading and estab framework of rockbolting in field conditions, a theoretical model, and correspo boratory configuration ( Figure 1) [35]. For laboratory testing to reflect the real sit confining tube with the same radial stiffness to the surrounding rock should be to prepare the testing sample. Under plane stress analysis, according to Lame's equation, the radial stiff tube and the infinite surrounding rock can be expressed as [36]: Rockbolting models, modified [34].
Under plane stress analysis, according to Lame's equation, the radial stiffness of a tube and the infinite surrounding rock can be expressed as [36]: where E is the elastic modulus of tube material, MPa; v is Poisson's ratio of the tube material; a is the inner tube diameter (borehole radius), mm; b is the outer tube diameter, mm; E r is the elastic modulus of the surrounding rock, MPa; and v r is Poisson's ratio of the surrounding rock. For a specific mining site or roadway, the equivalent radial stiffness principle should be implemented in laboratory SEPT design, i.e.,

Equivalent Radial Stiffness Calculation
To provide an overview of the tube, the surrounding rock classification is introduced here. On the basis of integrality, the uniaxial compressive strength (UCS) of the saturated rock sample (R b ) and the self-stability time of the surrounding rock, the surrounding rock was classified into 5 categories in the underground mining industry in China, namely, (I) stable strata, (II) fair stable strata, (III) medium-stable strata, (IV) poor stable strata, and (V) unstable strata [37]. According to the magnitude of R b , it can be roughly simplified into 3 categories: for R b > 60 MPa, the surrounding rock is strong; for 30 < R b < 60 MPa, the surrounding rock is medium-strong; and for R b < 30 MPa, the surrounding rock is weak [38]. According to the statistical relationship between UCS and the elastic properties of the rock, the strong, medium-strong, and weak surrounding rocks correlate to E r > 50 GPa and v r = 0.15 − 0.20, E r = 15 − 50 GPa and v r = 0.20 − 0.25, and E r < 15 GPa and v r = 0.25 − 0.30, respectively.
In China, borehole diameter was usually about 30 mm in the bolting support of a coal mine, i.e., a = 30 mm. Accordingly, by substituting the above parameters into Equation (3)  where E is the elastic modulus of tube material, MPa; is Poisson's ratio of the tube material; a is the inner tube diameter (borehole radius), mm; b is the outer tube diameter, mm; is the elastic modulus of the surrounding rock, MPa; and is Poisson's ratio of the surrounding rock. For a specific mining site or roadway, the equivalent radial stiffness principle should be implemented in laboratory SEPT design, i.e., = (3

Equivalent Radial Stiffness Calculation
To provide an overview of the tube, the surrounding rock classification is introduced here. On the basis of integrality, the uniaxial compressive strength (UCS) of the saturated rock sample ( ) and the self-stability time of the surrounding rock, the surrounding rock was classified into 5 categories in the underground mining industry in China, namely, (I stable strata, (Ⅱ) fair stable strata, (Ⅲ) medium-stable strata, (Ⅳ) poor stable strata, and (Ⅴ) unstable strata [37]. According to the magnitude of , it can be roughly simplified into 3 categories: for > 60 MPa, the surrounding rock is strong; for 30 < <60 MPa the surrounding rock is medium-strong; and for < 30 MPa, the surrounding rock i weak [38]. According to the statistical relationship between UCS and the elastic propertie of the rock, the strong, medium-strong, and weak surrounding rocks correlate to    Figure 2 shows that, on the basis of the equivalent radial stiffness principle, tubes composed of PVC, #6061 Al, and #20 steel with proper wall thickness nearly cover the full range of the surrounding rock's strength. Figure 2 does not give the corresponding tube materials and wall thickness of the surrounding rock with the elastic modulus of 3.5 to 15 GPa, and materials such as C20 to C40 concrete can be used to mimic the surrounding rock or used material with an elastic modulus of roughly 20 to 30 GPa. Currently, the material with an elastic modulus of roughly 20 to 30 GPa has not been found to be available, and using C20 to C40 concrete is the universal method used by many researchers. Consequently, a series of laboratory SEPT were conducted to investigate the anchorage performance of dextral bolts under different confining materials.

Laboratory Configuration
(1) Bolt Two kinds of dextral bolt were studied. First was the original dextral bolt commonly used in underground support. It is a dextral-threaded, nonlongitudinal imprint with a diameter of 20 mm and rib spacing of 12 mm. Second was a modified dextral bolt, which was in a rib spacing of 48 mm through polishing out three transverse ribs. Both bolts were cut to a length of 280 mm, as shown in Figure 3. Table 1 shows the geometric and mechanical parameters of the testing bolts.
Appl. Sci. 2021, 11, 8041 5 of 1 Figure 2 shows that, on the basis of the equivalent radial stiffness principle, tube composed of PVC, #6061 Al, and #20 steel with proper wall thickness nearly cover the fu range of the surrounding rock's strength. Figure 2 does not give the corresponding tub materials and wall thickness of the surrounding rock with the elastic modulus of 3.5 to 1 GPa, and materials such as C20 to C40 concrete can be used to mimic the surroundin rock or used material with an elastic modulus of roughly 20 to 30 GPa. Currently, th material with an elastic modulus of roughly 20 to 30 GPa has not been found to be avai able, and using C20 to C40 concrete is the universal method used by many researchers Consequently, a series of laboratory SEPT were conducted to investigate the anchorag performance of dextral bolts under different confining materials.

Laboratory Configuration
(1) Bolt Two kinds of dextral bolt were studied. First was the original dextral bolt commonl used in underground support. It is a dextral-threaded, nonlongitudinal imprint with diameter of 20 mm and rib spacing of 12 mm. Second was a modified dextral bolt, whic was in a rib spacing of 48 mm through polishing out three transverse ribs. Both bolts wer cut to a length of 280 mm, as shown in Figure 3. Table 1 shows the geometric and me chanical parameters of the testing bolts.  (2) Confining tubes The tubes were composed of PVC, # 6061 Al, and # 20 steel, respectively. The geo metric parameters of the tubes are shown in Figure 4. The inner wall was treated throug wire cutting to 1.0 mm depth to enhance the friction between resin and the inner wall o the tube, thus that there was no slippage in the resin-tube interface over the pull-out pro cess [39].  (2) Confining tubes The tubes were composed of PVC, # 6061 Al, and # 20 steel, respectively. The geometric parameters of the tubes are shown in Figure 4. The inner wall was treated through wire cutting to 1.0 mm depth to enhance the friction between resin and the inner wall of the tube, thus that there was no slippage in the resin-tube interface over the pull-out process [39].

(3) Resin anchorage agent
In this test, medium-curing-time resin produced in accordance with the MT146.1-2011 standard [40] was used as the grouting material. On the basis of uniaxial compressive and shear tests, the UCS of the resin grout was 60.9 MPa, cohesion was 19.1 MPa, and the internal friction angle was 32.3 • .  (3) Resin anchorage agent In this test, medium-curing-time resin produced in accordance with the MT146.1-2011 standard [40] was used as the grouting material. On the basis of uniaxial compressive and shear tests, the UCS of the resin grout was 60.9 MPa, cohesion was 19.1 MPa, and the internal friction angle was 32.3°.
(4) Pull-out specimens After the resin had been cured, the specimens were placed in an incubator at a temperature of (22 ± 1) °C for 24 h. The pretesting specimens are shown in Figure 5.

Experimental Results
High-strength # 40 Cr steel was used to manufacture a pulling cell to content the testing specimen. WAW-600C microcomputer-controlled electrohydraulic servo-testing machine was used to conduct the test, and loading displacement was controlled at a speed of 1 mm/s. Figure 6 illustrates the pull-out testing arrangement. (4) Pull-out specimens After the resin had been cured, the specimens were placed in an incubator at a temperature of (22 ± 1) • C for 24 h. The pretesting specimens are shown in Figure 5. In this test, medium-curing-time resin produced in accordance with the MT146.1 2011 standard [40] was used as the grouting material. On the basis of uniaxial compressiv and shear tests, the UCS of the resin grout was 60.9 MPa, cohesion was 19.1 MPa, and th internal friction angle was 32.3°.
(4) Pull-out specimens After the resin had been cured, the specimens were placed in an incubator at a tem perature of (22 ± 1) °C for 24 h. The pretesting specimens are shown in Figure 5.

Experimental Results
High-strength # 40 Cr steel was used to manufacture a pulling cell to content th testing specimen. WAW-600C microcomputer-controlled electrohydraulic servo-testin machine was used to conduct the test, and loading displacement was controlled at a spee of 1 mm/s. Figure 6 illustrates the pull-out testing arrangement.

Experimental Results
High-strength # 40 Cr steel was used to manufacture a pulling cell to content the testing specimen. WAW-600C microcomputer-controlled electrohydraulic servo-testing machine was used to conduct the test, and loading displacement was controlled at a speed of 1 mm/s. Figure 6 illustrates the pull-out testing arrangement. Figure 7 shows the load-displacement curves of all tests. There were three pull-out specimens for each type of confining tubes. Table 2 lists the average axial anchorage load capacity and standard deviation of the axial force. It shows that, for the original dextral bolt compared with PVC tube specimens, the average peak anchorage force of the Al tube and the steel tube specimens increased by 31.5%, 78.0%, and 97.3%, respectively. For the modified dextral bolt, the peak anchorage force of the Al tube and the steel tube specimens increased by 22.5%, 89.6%, and 99.8%, respectively, compared to that of the PVC tube. The axial load capacity of the bolt thus increased with an increase in the radial stiffness of the confining materials; anchorage performance may be quite different for the same dextral bolting support system but in the different surrounding rock. Meanwhile, the experimental results also highlight the influence of rib spacing on the anchorage force. In this case, increasing the rib spacing also increases the anchorage force, as reported by experimental works [24].  Figure 7 shows the load-displacement curves of all tests. There were three pull-ou specimens for each type of confining tubes. Table 2 lists the average axial anchorage loa capacity and standard deviation of the axial force. It shows that, for the original dextra bolt compared with PVC tube specimens, the average peak anchorage force of the Al tub and the steel tube specimens increased by 31.5%, 78.0%, and 97.3%, respectively. For th modified dextral bolt, the peak anchorage force of the Al tube and the steel tube specimen increased by 22.5%, 89.6%, and 99.8%, respectively, compared to that of the PVC tube. Th axial load capacity of the bolt thus increased with an increase in the radial stiffness of th confining materials; anchorage performance may be quite different for the same dextra bolting support system but in the different surrounding rock. Meanwhile, the exper mental results also highlight the influence of rib spacing on the anchorage force. In th case, increasing the rib spacing also increases the anchorage force, as reported by exper mental works [24].     Figure 7 shows the load-displacement curves of all tests. There were three pull-out specimens for each type of confining tubes. Table 2 lists the average axial anchorage load capacity and standard deviation of the axial force. It shows that, for the original dextral bolt compared with PVC tube specimens, the average peak anchorage force of the Al tube and the steel tube specimens increased by 31.5%, 78.0%, and 97.3%, respectively. For the modified dextral bolt, the peak anchorage force of the Al tube and the steel tube specimens increased by 22.5%, 89.6%, and 99.8%, respectively, compared to that of the PVC tube. The axial load capacity of the bolt thus increased with an increase in the radial stiffness of the confining materials; anchorage performance may be quite different for the same dextral bolting support system but in the different surrounding rock. Meanwhile, the experimental results also highlight the influence of rib spacing on the anchorage force. In this case, increasing the rib spacing also increases the anchorage force, as reported by experimental works [24].

Anchorage Force vs. Radial Stiffness
Using Equation (1), the radial stiffness of the tubes of PVC, Al, and steel with wall thicknesses of 5.5 and 7.5 mm used in the test could be calculated as 0.15, 1.00, 2.90, and 3.63 GPa/mm, respectively. Figure 8a,b show the relationships of the average peak anchorage force with the radial stiffness of confinement for the original and modified dextral bolting sample, respectively. Combined with Figure 2 and Equation (1), the radial stiffness of 0.85 and 2.90 GPa/mm represent the boundaries between the weak/mediumstrong and medium-strong/strong surrounding rock, respectively, as indicated by the two dotted blue lines in Figure 8a,b. thicknesses of 5.5 and 7.5 mm used in the test could be calculated as 0.15, 1.00, 2.90, and 3.63 GPa/mm, respectively. Figure 8a,b show the relationships of the average peak anchorage force with the radial stiffness of confinement for the original and modified dextral bolting sample, respectively. Combined with Figure 2 and Equation (1), the radial stiffness of 0.85 and 2.90 GPa/mm represent the boundaries between the weak/medium-strong and medium-strong/strong surrounding rock, respectively, as indicated by the two dotted blue lines in Figure 8a To study the pattern of the bolting capacity vs confinement curves, the following negative exponential relationship was proposed for peak anchorage force and the radial stiffness of the confinement in this study: where is the anchorage load capacity (kN); S is the radial stiffness of confining material (GPa/mm); A is a constant, it is the peak anchorage force while S→+∞; B is a constant, thus that (A-B) equals the peak anchorage force at S→0; and C is the curvature parameter. Using Equation (4) to fit the experimental data of the two kinds of dextral bolt, the fitting curves of the peak anchorage force and the stiffness of the confinement for original and modified dextral bolts can be expressed as the following equations, shown in Figure  8a,b, respectively.
Determinations for Equations (5) and (6) are 0.99; thus, Equation (4) is suitable to determine the relationship between peak anchorage force and stiffness of the confinement. To study the pattern of the bolting capacity vs confinement curves, the following negative exponential relationship was proposed for peak anchorage force and the radial stiffness of the confinement in this study: where F P is the anchorage load capacity (kN); S is the radial stiffness of confining material (GPa/mm); A is a constant, it is the peak anchorage force while S→+∞; B is a constant, thus that (A−B) equals the peak anchorage force at S→0; and C is the curvature parameter. Using Equation (4) to fit the experimental data of the two kinds of dextral bolt, the fitting curves of the peak anchorage force and the stiffness of the confinement for original and modified dextral bolts can be expressed as the following equations, shown in Figure 8a,b, respectively.  (5) and (6) are 0.99; thus, Equation (4) is suitable to determine the relationship between peak anchorage force and stiffness of the confinement.

Validity Study of Equation (4)
This section further discusses the validity of Equation (4). In the equation, parameter A is the theoretical peak anchorage force when the radial stiffness of the confinement S→+∞, i.e., the peak axial force of a bolt anchored within an extremely rigid confining rock mass. A previous study [41] identified that rockbolting failure while subjected to the axial load can be classified into two modes: parallel shear failure and expansive slippage failure, as shown in Figure 9.
This section further discusses the validity of Equation (4). In the equation, paramete A is the theoretical peak anchorage force when the radial stiffness of the confinemen S→+∞, i.e., the peak axial force of a bolt anchored within an extremely rigid confining roc mass. A previous study [41] identified that rockbolting failure while subjected to the axia load can be classified into two modes: parallel shear failure and expansive slippage fail ure, as shown in Figure 9. Parallel shear failure occurs along a cylindrical interface between bolt and resin, whereas expansive slippage failure takes place within the resin material under the transverse rib of the bolt and then slips along the axial direction while expanding in the surrounding material. Under the condition of the infinite radial stiffness of the confining tube, expansion slip failure cannot occur. In other words, anchorage failure can merely exhibit parallel shear failure. In such a situation, the axial force of the bolt equals the shear stress along the failure interface [41]: where F T is the axial load (N); τ bg is the shear stress along the resin/bolt interface (MPa); A bg is the area of the resin/bolt interface (mm 2 ); τ g is the shear strength of the resin of the parallel shear failure interface (MPa); and A g is the area of the parallel shear failure interface (mm 2 ). In critical state, c bg is the cohesion of the resin-bolt interface (MPa); p is the confining pressure when failure occurs (MPa); φ bg is the internal friction angle of the resin-bolt interface ( • ); c g is the resin cohesion (MPa); and φ is the internal friction angle of resin ( • ). According to the specimen size and dextral-bolt dimensions (Table 1 and Figure 9), ratios l/L were 64% and 91% for the original and modified dextral-threaded bolt, respectively. The outer diameter of the bolt R = 11.8 mm under both conditions. Therefore, for the bolt with a rib spacing of 12 mm, we have A bg = 2657 mm 2 and A g = 4757 mm 2 . For the bolt with the rib spacing of 48 mm, we have A bg = 664 mm 2 and A g = 6750 mm 2 . For resin mechanical properties, c g = 19.1 MPa and φ =32.3 • ; for the mechanical properties resin-steel interface, we assumed c bg = c g /2 and φ bg = φ/2. Confining pressure p is mainly caused by the shrinkage of the resin, thus, we assumed p = 5.0 MPa [41]. Substituting these parameters into Equations (7)-(9), the theoretical F T12 = 135.1 kN, and F T48 = 157.6 kN. Compared with the experimental data of F p12 = 146.0 kN and F p48 = 174.8 kN, two theoretical values agreed well.
According to Equation (3), (A−B) is the anchorage force when radial stiffness S→0. At present, there is no commonly accepted approach to estimate the peak anchorage force in such situations. The minimal peak anchorage force should be related to bolt type and grout strength but is independent of the surrounding rock conditions. In this study, the theoretical peak anchorage force without the radial stiffness of confining material for the original dextral bolt was 58.9 kN, which can be used as a reference for subsequent study. Figure 10 shows the post-testing specimens. Two failure modes can be identified. The failure interface of the bolting specimens with a rib spacing of 12 mm was nearly a regular cylinder surface, which indicates that its predominant failure mode was a parallel shear failure. For the dextral bolt with rib spacing of 48 mm, the grout of specimens was relatively broken, and blocky grout accumulated beneath the transverse rib, suggesting that of the bolt was dominated by the expansive slippage failure. The difference between these two failure modes can be understood in the previous study [41]. In addition, it suggests that changing the rib spacing can change the failure mode and process of the anchorage system. Therefore, it may improve the bolt anchoring performance by optimizing the bolt rib spacing.

Failure Mode
is the internal friction angle of the resin-bolt interface (°); is the resin cohesion (MPa); and is the internal friction angle of resin (°). According to the specimen size and dextral-bolt dimensions (Table 1 and Figure 9), ratios l/L were 64% and 91% for the original and modified dextral-threaded bolt, respectively. The outer diameter of the bolt R = 11.8 mm under both conditions. Therefore, for the bolt with a rib spacing of 12  According to Equation (3), (A-B) is the anchorage force when radial stiffness S→0. At present, there is no commonly accepted approach to estimate the peak anchorage force in such situations. The minimal peak anchorage force should be related to bolt type and grout strength but is independent of the surrounding rock conditions. In this study, the theoretical peak anchorage force without the radial stiffness of confining material for the original dextral bolt was 58.9 kN, which can be used as a reference for subsequent study. Figure 10 shows the post-testing specimens. Two failure modes can be identified. The failure interface of the bolting specimens with a rib spacing of 12 mm was nearly a regular cylinder surface, which indicates that its predominant failure mode was a parallel shear failure. For the dextral bolt with rib spacing of 48 mm, the grout of specimens was relatively broken, and blocky grout accumulated beneath the transverse rib, suggesting that of the bolt was dominated by the expansive slippage failure. The difference between these two failure modes can be understood in the previous study [41]. In addition, it suggests that changing the rib spacing can change the failure mode and process of the anchorage system. Therefore, it may improve the bolt anchoring performance by optimizing the bolt rib spacing.

Conclusions
SEPT is an effective approach to study the reinforcement mechanism and boltingsupport technology. To realize laboratory SEPT results reflecting site conditions, the influence of radial stiffness on reinforcement performance was studied. The following conclusions are summarized on the basis of laboratory testing and theoretical analysis. . This can be used to improve the accuracy of laboratory SEPT results towards the site outcome ( Figure 2). (2) Two kinds of dextral-threaded bolt were studied using the developed method of this study. PVC, Al, and steel tubes were used as confinement in laboratory SEPT, and anchorage performance was obtained under different surrounding rock strength levels ( Figure 7). The results show that axial load capacity increased with the increase in radial stiffness of the confining materials. Compared with PVC tube specimens, peak axial force was nearly double when using thick steel tubes ( Table 2). (3) On the basis of theoretical analysis and curve fitting, the relationship between the average peak axial force and radial stiffness of the confining materials was proposed to be a negative exponential (Equation (4)) function. A validity study was conducted, and its result showed that the proposed relationship agreed well with the theory in the literature. The developed equation could be used to determine the performance of a specific bolt under different field geoconditions and provide accurate parameters for numerical modeling. (4) Post-testing specimens showed that the failure modes of the original and modified dextral bolts were parallel shear failure and expansive slippage failure, respectively ( Figure 10). As anchorage performance is determined by the load-transfer mechanism in a bolting system, which is closely related to the failure model of rockbolting, it may be practical to design and realize different anchorage effects for different field geoconditions via controlling the technology of rockbolting failures, such as with rebar-profile modification.