Effects of Organic Additives on Chemical, Microbiological and Plant Pathogen Suppressive Properties of Aerated Municipal Waste Compost Teas

: The aim of the present study was to characterize the physical-chemical and microbiological features of aerated compost teas (CTs) extracted with dechlorinated tap water and with two different additives, molasses and whey, in increasing doses. Plant pathogen suppression properties of CTs were also taken into account. Total nitrogen in CTs increased with rising doses of the additives used. In spite of this, nitrogen and mineral element contributions were limited but complementary for plant mineral nutrition. Although total heavy metal contents in CTs were low, an increase of their bioavailable forms (ionic and chelated forms, presence in microorganisms) should be taken into account. In addition, the distribution on soil of acid and/or chelating products by CTs could increase the bioavailability of heavy metals, especially in the case of several annual distribution cycles and of medium–long term treatments. Additives modulated the structure and composition of microbial communities and CTs, exhibiting a broad spectrum of suppressive properties against plant pathogens, especially when they were used in a raw form.


Introduction
The need for a reduction in the environmental impacts of synthetic pesticides and the new trends dictated by the market for organically managed cropping systems, has renewed interest in agricultural practices of the past, based on natural products, such as compost teas (CTs), which have been found to be effective in the control of many plant diseases [1]. CT is defined as an organic liquid formulate, obtained by water extraction of a quality compost, continuative for a defined period, under aerated (aerated CT, ACT) or not aerated (non-aerated CT, NCT) conditions, with or without nutritional additives [2]. CT has been proposed to be applied to soil and/or to plants through irrigation systems, soil drenching, or foliar spray with different aims, including control of leaf and/or soil crop diseases; microbial augmentation for restoring or increasing beneficial telluric microflora able to promote soil health; stimulation of the general plant physiological performances; and nutrients supply [3][4][5][6][7][8][9].
This agro-technique has been used under organic and biodynamic farming since 1920 [10]. It is stated that CTs exert positive actions due to the presence of soluble organic molecules, such as humic substances (humic and fulvic acids). These molecules may have a direct effect on plant metabolic processes (i.e., radical bio-stimulation, photosynthesis,

CTs in Comparison
CTs were obtained using a commercial municipal waste compost (COMPOSTA, Gesenu S.p.A. Perugia, Italy) authorized for the use in organic agriculture and finely screened (at 1 cm) in order to make it homogeneous. Compost came from composting of the humid fraction of urban wastes, and ligninic and cellulosic materials from maintenance of green urban areas. As requested by Italian law concerning fertilizers [22], the used compost was free from pathogenic bacteria (specifically Salmonella and Escherichia coli). Compost was extracted in a 1:5 ratio solution (v:v) with the addition of whey or molasses, as follows: CT-Wa = 7 L of compost + 35 L of dechlorinated tap water CT-Wh1 = 7 L of compost + 3 L of whey + 32 L of dechlorinated tap water CT-Wh2 = 7 L of compost + 5 L of whey + 30 L of dechlorinated tap water CT-M1 = 7 L of compost + 105 g of molasses + 35 L of dechlorinated tap water CT-M2 = 7 L of compost + 175 g of molasses + 35 L of dechlorinated tap water CT-M3 = 7 L of compost + 350 g of molasses + 35 L of dechlorinated tap water Whey (Wh) is a waste product of the dairy industry from the process of ricotta production and was provided from a local cheese factory. Molasses (M) is a discarded byproduct obtained from the sugar beet transformation process: a fluid commercial product, allowed in organic farming, was used in this research. The major chemical characteristics of the starting materials used to produce the different CTs are reported in Table 1. Electrical conductivity (EC) and pH were measured using a Crison 525 conductivimeter (Crison, Barcelona) and a Hanna Instruments HI 223 pH meter, respectively. Measurements were performed by immersing the probes in the CTs at the beginning of the extraction period (t 0 ) and, then every 30 min for the first five time points, and each hour for the remaining part of the experiment, which lasted 48 h (except at night). In particular, measurements were carried out immediately after air insufflation, which produced a turbulence effect, in order to guarantee correct homogenization of the extract. Total organic carbon (TOC), as well as humic and fulvic acids (HA and FA, respectively), were determined in the CTs sampled after 24 and 48 h of extraction, according to the official Italian method for compost analyses [23]. Particularly, for TOC measurements, potassium dichromate (K 2 Cr 2 O 2 ) and concentrated H 2 SO 4 were added to 10 mL of extract. After 10 min, distilled water was added to the solution to halt the digestion process. An indicator solution (barium diphenylamine sulfonate) was added to the digestate and then the excess Cr 2 O 7 2− was titrated with ferrous ammonium sulfate (Möhr salt). HA and FA were separated from 100 mL of the extract added with 1 mL of 50% sulphuric acid; the solution was stirred and left to stand for 30 min. Then, the sample was centrifuged at 3000 rpm for 20 min. After the centrifugation, the solid pellet, including insoluble HA under acid conditions, was suspended with 100 mL of distilled water and stored at 4 • C for subsequent analyses. The supernatant was poured into a polyvinylpyrrolidone column that was previously prepared. The column was washed five times with aliquots of 20 mL of 0.005 M H 2 SO 4 . The yellowish eluate coming out to the column was removed (the non-humified fraction). After these washings, the FA adsorbed on the resin at the upper end of the column were removed by slowly eluting aliquots of NaOH 0.5 M and collected in a 100-mL flask.
Humified organic carbon was determined in the two collected fractions (HA and FA). In particular, 10 mL was added with 5 mL of K 2 Cr 2 O 7 2N and 20 mL of concentrated H 2 SO 4 . The mixture was kept at 160 • C for 10 min. Then, distilled water was added to stop the reaction. The excess potassium dichromate was measured out by Möhr salt titration in the presence of a diphenylamine indicator.

Total and Ammonia Nitrogen
Total (Total-N) and ammonia nitrogen (N-NH 4 ) were analyzed in the CTs sampled at the end of the extraction procedure (48 h) by means of Kjeldahl method.
For Total-N determination, concentrated sulfuric acid and catalysts were added to 10 mL of extract. The solution was subjected to a gradual heating, up to a temperature of 360 • C, and maintained at this temperature for 3 h (until the sample became clear and colorless). Then, solution was alkalized with sodium hydroxide (40%) and distilled in a vapor stream. The distillate was collected in a solution of boric acid (1%) and titrated with HCl 0.05 N with few drops of bromocresol green-methyl red mixture.
Ammonia nitrogen was determined directly with 10 mL of non-mineralized extract.

Heavy Metals, Alkali Metals and Alkaline Earth Metals
Heavy metals, alkali metals, and alkaline earth metals (Cd, Cr, Cu, Fe, Ni, Pb, Zn, Na, K, Mg, Ca) were analyzed on the starting materials (tap water, whey, and molasses) ( Table 1) and the resulting CTs were sampled at the end of the extraction procedure. Ten milliliters of such material was previously subjected to an acid digestion at rising temperature steps, using a microwave oven (Milestone). Metal concentrations were determined in the extracts using an ICP-OES spectrometer (iCAP 6000 Series, Thermo Scientific, Waltham, MA, USA).
The enrichment factor was calculated as the ratio between the individual metal content in each final CT and the content in the correspondent extracting solution (tap water or tap water with the addition of additives, molasses and whey, in different quantities): The sodium adsorption ratio (SAR), as a salinity indicator, was calculated for the final CTs, according to the following formula: where Na, Ca and Mg are expressed in meq L −1 .

Biolog Analyses and Bacterial Community Levels of Physiological Profiles
Bacterial community levels of physiological profiles (CLPPs) were assessed by using the Biolog ® ECO microplates TM system (Biolog Inc., Hayward, CA, USA). Aliquots (100 µL) of each CT (sampled at the end of the extraction process) diluted at 10 −3 were inoculated in each well. The plates were incubated at 25 • C for 4 days and color development in each well was recorded daily as optical density at 590 nm using a Bio-Rad Microplate Reader 550 (Biorad, Hercules, CA, USA). Measures were carried out in triplicate. Average well color development (AWCD) and Shannon index (H') were determined, as described by Pane et al. [27]: where Ai is the absorbance value in the ith well and Ac is the absorbance in the control (blank).
where Pi is the ratio between the absorbance value in the ith well and the total absorbance values of all the wells. The AWCD data were used to develop the Boltzmann function. The variability coefficient (VC) was calculated as follow: where SD is the standard deviation.

In Vitro Suppression Assay of CTs
Fungi used in this assay were: Alternaria sp., Botrytis cinerea, Colletotrichum lindemuthianum, Fusarium oxysporum f. sp. lycopersici, Fusarium semitectum, Fusarium solani, Pyrenochaeta lycopersici, Rhizoctonia solani and Verticillium dahlie, which were maintained on potato dextrose agar (PDA) medium at 20 • C. In vitro suppression by CTs was evaluated on samples recovered after 48 h from the start of the extraction process, and was carried out using the well-cut diffusion technique [27] with modifications. Twenty milliliters of sterile PDA medium were poured into 90 mm plates and, after solidifica-tion, four wells were then punched out using a 0.5 cm sterile cork borer, orthogonally, on the edge of each plate. Each of the well bottoms was sealed with two drops of sterile water agar. One hundred microliters of different diluted teas were transferred into each well, and sterile water was placed in the wells of the control plates. One disc (0.5 cm) of mycelium of each fungus was inverted and placed centrally between the wells on PDA medium. All plates were incubated at 25 • C, until the mycelium reached the wells in water-amended control plates. After incubation, the radius of the clear zone around each well was measured linearly.

Rhizoctonia Disease Suppressiveness Assay by CTs
One-month-old kohlrabi (Brassica oleracea var. gongylodes) nursery seedlings, were used to screen the in vivo CT suppressive ability. Pots (20 cm diam.) filled with sterile peat were inoculated with R. solani-infected common millet seeds prepared, as described by Pane et al. [28], at 0.5% (w/w, dry weight). Non-inoculated common millet was added to healthy control pots. Five pots per treatments were used and five plants/pot were transplanted and drenched with 100 mL of 1:10 water diluted CT each. The treatments included the six CTs sampled at 48 h from the start of extraction, one healthy control and one non-treated infected control. The pots were then placed in a growth chamber (25 • C) in a completely randomized experimental design. After three weeks, the number of symptomatic plants per pot was measured to calculate disease incidence as percentage of diseased plants. The total fresh and dry weight of plants per pot (g pot −1 ) was also recorded. The assay was repeated.

Phytotoxicity Assays
Assays on seed germination and root growth inhibition [29] were carried out to determine the phytotoxicity effects of the six CTs sampled after 24 and 48 h from the start of extraction. Seeds of three dicotyledonous plants, Cucumis sativus L., Lepidium sativum L. and Solanum lycopersicum L., were used. Five replicates for each CT were tested. For each species, ten seeds were placed in 10 cm Petri dishes, containing 10 mL of CT diluted with water in a 1:3 ratio (v:v; CT: water) and a paper filter. The control was performed in five replicates, using ultrapure water. The seeds were incubated for 72 h in a dark environment at 25 • C. At the end of the test, the germinated seeds were counted and their root extensions were measured using standard procedures. The germination index (GI) was then calculated by multiplying the average of the germinated seeds and the average of root elongation at the end of the test. The percentage of GI (GI%) was determined as the percentage of the ratio between the GI of the sample and the GI of the control:

Statistical Analyses
Statistical analysis of the data (ANOVA) was carried out using Sigmastat 3.1 SPSS Inc. software. Means that were statistically different were separated according to Duncan's multiple range test at p < 0.05.

Substrates and Additives Characteristics
Chemical and physical features of the compost and the additives used to produce CTs are reported in Table 1. Whey showed acid pH values, low N content and TOC content higher than that shown by molasses (33 g kg −1 versus 10 g kg −1 ). Differently, molasses had an alkaline reaction and showed a N concentration equal to 3%. Differences among additives were observed, even in metal concentrations. Molasses showed higher metal contents than whey, except for Fe. On the other hand, considering the total amounts of constituents used to produce the different CTs, whey supplied higher amounts of metals than molasses with the exception for Mn and Zn (Table 2).

Electrical Conductivity and pH
During the extraction process, the temperature of all CTs was around 19 • C (as the room temperature). EC and pH during the extraction process (0 h, 24 h and 48 h from the start of the process) are reported in Table 3. Table 3. pH and electrical conductivity (EC) measured in the CTs during the extraction process (at 0 h, after 24 h, after 48 h). Comparison between total organic carbon (TOC, g L −1 ), humic and fulvic acids (HA + FA, g L −1 ), and humic and fulvic acids to TOC ratio [(HA + FA)/TOC] × 100, measured after 24 and 48 h from the start of the extraction process.  From the start to the end of CTs extraction, pH values showed a slight increasing trend in both CT-Wa and in all the CTs obtained with molasses addition (Table 3). CT-Wh1 and CT-Wh2 pH decreased from 0 to 24 h to then reach values close to the starting ones.
Marked differences were observed for EC from 0 h to 48 h (Table 3). A more detailed description of the EC pattern is displayed in Figure 1. Particularly, it evolved according an exponential model (sigmoidal) for all the CTs, even if it showed (just after 24 h) growing values according to the following sequence CT-Wh2 > CT-M3 > CT-Wh1 > CT-M2 > CT-M1 > TC-Wa. The same sequence was also observed after 48 h (Figure 1). an exponential model (sigmoidal) for all the CTs, even if it showed (just after 24 h) growing values according to the following sequence CT-Wh2 > CT-M3 > CT-Wh1 > CT-M2 > CT-M1 > TC-Wa. The same sequence was also observed after 48 h (Figure 1).

Figure 1.
Electrical conductivity (EC) measured in the different CTs during the extraction procedure. Measurements were performed at the beginning of the extraction and then every 30 min for the first five surveys, and each hour for the remaining part of the experiment (except at night).

Total Organic Carbon, Humic and Fulvic Acids
The organic components measured after 24 and 48 h from the start of the extraction process, are reported in Table 3. By comparing the two sampling points, CT-Wa, CT-Wh1 and CT-Wh2 showed similar TOC values, while TOC decreased in molasses-added CTs after 48 h of extraction. Different behavior was followed by the humic-like substances, which decreased along with time in CT-Wa and CT-M1, whereas it increased in CT-Wh1, CT-M2 and CT-M3. In these cases, the humic fraction showed a greater weight on the value of TOC. CT-Wh2 had the highest content of humic-like substances (Table 3).

Chemical Features of the Final CTs and Their Dilutions
The chemical characteristics of the final CTs are reported in Table 4. With respect to the pH values, Wh-CTs could be classified as acid to sub-acid. The pH of the remaining CTs showed an alkaline reaction. EC of the final CTs ranged from 4.45 to 8.20 mS cm −1 , resulting particularly high and not suitable for a direct agronomical application of CTs.

Total Organic Carbon, Humic and Fulvic Acids
The organic components measured after 24 and 48 h from the start of the extraction process, are reported in Table 3. By comparing the two sampling points, CT-Wa, CT-Wh1 and CT-Wh2 showed similar TOC values, while TOC decreased in molasses-added CTs after 48 h of extraction. Different behavior was followed by the humic-like substances, which decreased along with time in CT-Wa and CT-M1, whereas it increased in CT-Wh1, CT-M2 and CT-M3. In these cases, the humic fraction showed a greater weight on the value of TOC. CT-Wh2 had the highest content of humic-like substances (Table 3).

Chemical Features of the Final CTs and Their Dilutions
The chemical characteristics of the final CTs are reported in Table 4. With respect to the pH values, Wh-CTs could be classified as acid to sub-acid. The pH of the remaining CTs showed an alkaline reaction. EC of the final CTs ranged from 4.45 to 8.20 mS cm −1 , resulting particularly high and not suitable for a direct agronomical application of CTs.
SAR, as a salinity index, ranged from a minimum of 2.4, measured for CT-Wh2, to 8.1 for CT-M3 (Table 4).
In all CTs, total N content showed an increasing trend with respect to the concentration measured in CT-Wa. Such increases were proportional to the applied doses of additives. Total N concentrations ranged from 97 mg L −1 measured in CT-Wa to 288 mg L −1 found in CT-M3 (Table 4). On average, N-NH 4 + represented 22% of the total N, ranging from a minimum of 15% and a maximum of 26%.
Whey CTs showed the highest TOC contents followed by the molasses ones and finally CT-Wa (Table 4). The lowest HA + FA value was observed for the CT-Wa which accounted for a low TOC to HA + FA ratio (1.66%). The humified fraction ranged from 0.25 to 0.66 g L −1 for the other CTs (Table 4) which showed decreasing TOC to HA + FA ratios, according to the following sequence CT-M1 < CT-Wh2 < CT-Wh1 < CT-M2 < CT-M3. A general increase in the metals concentration was observed in all CTs with additives compared to the CT obtained only with water addition (Table 4). Such evidence was confirmed by the enrichment factors of the CTs, calculated as the ratio between the heavy metal concentration in CT and the concentration in the corresponding extracting solution (Table 5). Such findings underline the high extractive capacity of metals from the compost.  Figure 2 shows pH and EC values measured in the CT diluted with tap water. The CTs seemed well buffered at all the dilutions examined. All the extracts at dilution ratio 1:4 (CT to water) showed EC ranging from 1 and 2 mS cm −1 . Such EC values are opportune for agronomical purposes (CT distribution by means of an irrigation system).
1:4 (CT to water) showed EC ranging from 1 and 2 mS cm −1 . Such EC values are opportune for agronomical purposes (CT distribution by means of an irrigation system).

Microbiological Features
Microbial counting revealed the effects of additives in changing the levels of the culturable populations, as shown in Table 6. Whey CTs showed the highest level of fungi Log CFU, while yeast population were higher in CT-M1, followed by CT-W2, than the others. Total bacteria population levels were significantly increased by both additives compared to CT-Wa, with a pattern that only for whey was increasing in a dose-dependent manner. Microbial population consistency revealed that fungi-to-bacteria and fungi-to-yeast ratios were higher in whey CTs, while yeast-to-bacteria ratio was fluctuating around the control value (Table 6). Bacillus spp. were not affected by additives, contrary to what happened for the others, which showed significant increases. For example, Pseudomonas spp. were higher in whey-amended CTs.

Microbiological Features
Microbial counting revealed the effects of additives in changing the levels of the culturable populations, as shown in Table 6. Whey CTs showed the highest level of fungi Log CFU, while yeast population were higher in CT-M1, followed by CT-W2, than the others. Total bacteria population levels were significantly increased by both additives compared to CT-Wa, with a pattern that only for whey was increasing in a dose-dependent manner. Microbial population consistency revealed that fungi-to-bacteria and fungi-toyeast ratios were higher in whey CTs, while yeast-to-bacteria ratio was fluctuating around the control value (Table 6). Bacillus spp. were not affected by additives, contrary to what happened for the others, which showed significant increases. For example, Pseudomonas spp. were higher in whey-amended CTs. Additives significantly influenced the assessed community levels of physiological profiles ( Table 7). The indexes describing the metabolic diversity, such as H' and VC, increased by the addition of additives: molasses, in particular, induced highest increments that were directly linked to the dose that was applied. The general metabolic activity, described by Boltzmann transformation of BIOLOG AWCD, indicated a similar behavior (Table 7).

CTs Fungal Pathogen Suppressiveness
All raw CTs exhibited in the plate diffusion assays, variable levels of fungal growth inhibition (Table 8). Plate experiments showed a reduction of mycelial development that ranged between 61 and 21%, with a global value that are, on average, around 45%. Although, additive type and dose and dilution interact significantly (MANOVA) with in vitro CTs suppression, all these factors did not give univocal effects. Therefore, no consistent characterizing trend could be deducted. Sterilized teas, on the contrary, has not produced any inhibition hole; therefore, they proved to be ineffective in fungal growth reduction (data not shown).
In vivo assay showed that CTs significantly reduced the detrimental effects of the fungal pathogen Rhizoctonia solani on cabbage (Figure 3). Although CT-Wh1 treatment proved higher control activity, there were no differences among CTs.

Mycelial Inhibition Zone (%)
In vivo assay showed that CTs significantly reduced the detrimental effects of the fungal pathogen Rhizoctonia solani on cabbage (Figure 3). Although CT-Wh1 treatment proved higher control activity, there were no differences among CTs.  Figure 4 shows the effects of the application of the different CTs, sampled after 24 and 48 h from the beginning of the extraction, on the GI% of seeds of cucumber, cress, and tomato. Such an index allowed to synthetically evaluate the action of CTs on seed germination and root extension, which are physiological processes particularly sensitive to phytotoxic agents. Generally, CT-Wa was the least phytotoxic among the extracts: all species treated with CT-Wa showed the highest GI values, except in the case of cucumber treated with CT-M1 (Figure 4). In most cases, GI% decreased in treatments with higher additives concentrations in both sampling moments (24 and 48 h) even if these differ-  Figure 4 shows the effects of the application of the different CTs, sampled after 24 and 48 h from the beginning of the extraction, on the GI% of seeds of cucumber, cress, and tomato. Such an index allowed to synthetically evaluate the action of CTs on seed germination and root extension, which are physiological processes particularly sensitive to phytotoxic agents. Generally, CT-Wa was the least phytotoxic among the extracts: all species treated with CT-Wa showed the highest GI values, except in the case of cucumber treated with CT-M1 (Figure 4). In most cases, GI% decreased in treatments with higher additives concentrations in both sampling moments (24 and 48 h) even if these differences were not always statistically significant (Figure 4). With respect to the control, species responses to CTs applications were more evident in 24 h samples (Figure 4). A particular behavior was observed for tomato seeds, which showed a higher GI% values when they were treated with CTs after 48 h of extraction (Figure 4). ences were not always statistically significant (Figure 4). With respect to the control, species responses to CTs applications were more evident in 24 h samples (Figure 4). A particular behavior was observed for tomato seeds, which showed a higher GI% values when they were treated with CTs after 48 h of extraction ( Figure 4).

Discussion
In this study a quality commercial compost, suitable for use in organic agriculture as an amendment, was used to obtain CTs brewed with the addition of whey and molasses. These two by-products of the food transforming chain were used as additives, at different concentrations, to provide feeding sources for CT microbial populations.

Discussion
In this study a quality commercial compost, suitable for use in organic agriculture as an amendment, was used to obtain CTs brewed with the addition of whey and molasses. These two by-products of the food transforming chain were used as additives, at different concentrations, to provide feeding sources for CT microbial populations.
The chosen additives showed different chemical characteristics (i.e., molasses had higher pH values, N and heavy metal concentrations than the whey, which had greater TOC content), which supposedly affected the quality of the produced CTs, together with the applied doses and the duration of the extraction process. In particular, a 48 h-extraction duration was chosen with an intermediate sampling at 24 h, with the aim to cover the optimal brew time range and to observe maximum microbial activity in CTs [17].
The combination of the different starting feedstock (compost and additives) influenced pH and EC of CTs during the extraction process. This in accordance with what found by Kim et al. [30] after 2-day incubation of four types of aerated CTs. The low pH values showed by the whey CTs, especially after 24 h, could have an acidifying and potentially toxic effect on crops and increase the availability for absorption of heavy metals into the soil. Furthermore, the low pH of the whey CTs could accelerate irrigation system corrosion in fertigation applications. Conversely, a gradual increase of pH was shown by the CTs made using molasses, evidently due to its alkaline pH values. As reported by Schlegel [31], pH can strongly affect development of the microbial population. Acid pH measured in whey CTs probably favored growth of the fungal populations with respect to the bacterial groups. Caballero et al. [32] assessed the biostimulating properties of a fermented whey putatively associated to lactic acid, peptides, and free amino acids, with the further effect to lead microbial changes towards biocontrol active populations.
EC values in the experimental CTs, ranging from 4.45 to 8.20 mS cm −1 (Table 4), were well over the maximum threshold indicated for an irrigation water acceptable and usable without restriction [33], suggesting the need of the CT's dilution. Kim et al. [30] recorded significantly increased EC values of aerated CTs sampled after 1-day incubation, resulting in phytotoxic effects on cress seed germination, a species known to be highly sensitive to salt stress. In the current work, cress GI was negatively correlated to CTs electrical conductivity in both sampling points. An inverse behavior was observed on tomato seeds, which showed increased germination when treated with the CTs sampled after 48 h. This finding suggests further investigations on such a germination response.
With respect to the CTs dilutions, it seems that the best compost-to-water ratio for agronomical utilization was 1:4 for all the CTs produced. Such ratio assured EC values ranging from 1 to 2 mS cm −1 , which can be suitable for crop fertigation.
The suitability of CTs for soil treatment can be evaluated by means of both salt amounts and salt quality (especially the ratio among cations, Na + , Ca 2+ , Mg 2+ , in solution). SAR indicates sodium activity in CTs and how it can participate in the exchange process, which occurs in the soil in antagonism with calcium and magnesium. SAR showed by the CTs in comparison falls within the usual range in irrigation water [33]. As recommended by many Authors [5,17,34,35], a volume that is adequate enough to reach the root area should be applied to protect roots from potential colonization of pathogens and promote the growth of healthy plants. In addition, repeated applications are necessary in order to constantly supply the soil system with nutrients and beneficial microorganisms [17,34,35]. On the other hand, the repeated distribution of CT with a sodium imbalance could cause sodium accumulation into the soil (sodicity phenomenon), which has negative impacts on soil structure (swelling and dispersion of clays, soil surface crusting with consequent soil pore sealing). Therefore, sodicity can significantly affect water infiltration into the soil causing runoff and soil erosion especially on steep lands. In case of CT dilution, such detrimental agronomic/environmental effects can be reduced.
A certain increase in N content was observed in CTs produced with the addition of both whey and molasses. Such concentrations, although they are not exhaustive to fully satisfy nutritional requirements of horticultural or fruit crops to be treated, has to be considered complementary for nitrogenous nutrition of crops. By simulating the soil distribution of 300 L year −1 , as suggested by Ingham [17], the experimental CTs could apply total nitrogen inputs ranging from 29.1 to 86.4 g ha −1 . These amounts should be increased by fertilizers, taking into account other agronomical principles, such as the real nutrient needs of crops along the different stages of plant life cycle; soil nutrient availability and crop nutritional status; synchronization between nutrient requirements by the crops and their availability in soil volume where roots are present; fertilization techniques and their efficiency; soil management techniques and water availability linked to natural conditions (rainfall) or irrigation practice. Probably, a longer brewing period could allow a greater amount of nutrients to be extracted from the compost [36].
Generally, additives combined to the starting compost allowed to increase TOC and humic and fulvic acid concentrations within the final CTs. These organic matter forms, distributed in the soil by means of frequent CT applications, have important agronomic implications: they improve soil fertility, provide for labile nutrients and create an environment useful for microbial proliferation and activity, increase soil water retention [37,38]. The latter is a positive effect, especially in arid climates where irrigation water may be limited and high air temperatures quickens soil mineralization processes. In addition, humic substances can incite plant biostimulations by affecting both nutrient uptake and plant metabolism [39]. All such conditions create balanced and high-performance crop systems, able to cut plant chemical needs and reduce external inputs (pesticides, fertilizers).
The high capacity to extract metals from compost by the used additives suggests to take them into account in CT field application scheduling. The amount of elements with nutritional functions for crops, such as Ca, Mg and K, applied by means of CTs are low (data not shown) and, therefore, should be integrated according to the rules of sustainable fertilization. Monitoring of Ca/Mg and K/Mg rations in compost extracts is recommended to avoid possible equilibrium changes of these elements into the soil, which could affect crop nutrition. In order to determine whether heavy metal concentrations were of concern in terms of negative impacts on the soil system, they were compared with the chemical limits, where available, imposed by Italian legislation, which regulates the reuse of wastewater for irrigation purposes (Decree No. 185, 12/06/2003) [40]. With the exception of Cu, Fe and Mn, the contents were found to be below the limits permitted by law (Table 4). By assuming a CT-Wa, CT-Wh2 and CT-M3 distribution at a dose of 300 L year −1 for a medium period of 10 years, the total heavy metals applied to the soil are extremely low and well below the maximum annual quantities allowed by Legislative Decree No. 99, 27/01/1992 concerning the disposal on land of sewage sludge (application of 5 t ha −1 year −1 of sewage sludge-on a dry matter basis) [41] (Table 9). Although total heavy metal contents in the experimental CTs were low, an increase of their bioavailable forms (ionic and chelated forms, presence in microorganisms) should be taken into account. In addition, the distribution on soil of acid or/and chelating products by CTs, could increase the bioavailability of heavy metals, especially in the case of several annual distribution cycles and of medium-long term treatments. Table 9. Total heavy metals applicable to the soil in the medium period (10 years) by means of CT-Wa, CT-Wh2 and CT-M3 (300 L year −1 ). Comparison with the maximum annua1 amounts allowed by the Italian law (Legislative Decree, No. 99, 27/01/1992) through the application of 5 t ha −1 year −1 of sewage sludge-on a dry matter basis. Here, CTs exhibited a broad-spectrum of suppressive properties against the tested plant pathogens, interestingly, only when, independently from the concentration, they are used as raw. This means that pathogen containment was mainly due to the microbial components, probably responsible of antagonistic functions [42]. Actually, plate counts retrieved microbial populations, such as Pseudomonas spp. and Bacillus spp., associated to the biological control of plant pathogens [43,44]. As expected, additives modulated both the structure and composition of CT communities: molasses stimulated microbial shifts more than whey, likely due to sugar content. Nevertheless, the kind of additive did not univocally affect Rhizoctonia disease control efficacy, likely due to the high suppressive levels just showed by the non-amended tea. Interestingly, additive used at the higher dosage, reduced the suppressivity performances of the formulate suggesting strong effects on the microbial community composition. A literature survey showed how additives might have a role in suppressive functionalities and have a potential to help the definition of the systematic production of CTs suitable for plant disease management [5]. Mohd Din et al. [45] pointed up as an aerated CT added with molasses sourced from oil palm, was able to suppress Grammothele lineata on the Malaysian plant Melicope ptelefolia. CTs have a great potential to suppress both air and soil-borne pathogens [46], as also indicated here by the in vitro and in vivo experiments. In a previous assay, whey CTs significantly reduced disease symptoms of Alternaria alternata, Botrytis cinerea and Pyrenochaeta lycopersici on tomato, suggesting a suitability of the extracting solution for suppressive CTs production [42]. CTs may explicate the biocontrol action against plant diseases through the typical antagonistic mechanisms operated by the resident microflora, including antibiosis, competition for the space and/or for the nutrients, hyperparasitisms and induction of systemic resistance in the plants. Microbial biodiversity in the compost is crucial for the suppressive properties [47] that can be transferred into CT. In this regard, the additives may further affect the architecture of the microbial community, by favoring general growth or some populations over others (i.e., molasses) and/or by providing new microbial groups (i.e., whey) by establishing new equilibriums. Thus, the biocontrol mechanisms, on the base of the complexity of the resident communities, in the CT may synergize. The role of the specific antagonistic structure of microbial groups for the biological control activity has highlighted in CTs able at reducing disease symptoms caused by R. solani on savoy cabbage, Sclerotinia minor on lettuce and Sclerotium rolfsii on pepper in drenching applications [48].

Conclusions
CT is a multifunctional product, especially usable in organically managed agricultural systems and achievable on-farm at sustainable costs with easily available materials, for example biowaste from agro-food processing industries. CTs with additives have proven to be an important supplementary source in crop nutrition, to be taken into due consideration in drawing up fertilization plans. On the other hand, it is necessary to pay particular attention to the quality of the starting ingredients (compost, water, nutritional additives) to ensure the production of "safe" CT. Without prejudice to the use of quality CT, it is however advisable, for precautionary purposes, to monitor the system (soil-plant) treated with CT to avoid long-term undesirable effects (accumulation of heavy metals, salinization, phytotoxicity, etc.). The additives used in this research seem to have an interesting function of being a microbial starter and exert a significant restraint of the plant pathogen activities, probably by influencing and modulating CTs communities' compositions. The features of this sustainable technique (low costs, ease of application, waste recycling action, etc.), together with several agronomical benefits coming from its application, should justify a political and economic effort by competent bodies to spread it as much as possible to potential stakeholders (agro-food industries and operators, agricultural experts, farmers, etc.).