Comparative Analysis of Digital Models of Objects of Cultural Heritage Obtained by the “3D SLS” and “SfM” Methods

In the era of the global pandemic caused by the COVID-19 virus, 3D digitisation of selected museum artefacts is becoming more and more frequent practice, but the vast majority is performed by specialised teams. The paper presents the results of comparative studies of 3D digital models of the same museum artefacts from the Silk Road area generated by two completely different technologies: Structure from Motion (SfM)—a method belonging to the so-called low-cost technologies—and by Structured-light 3D Scanning (3D SLS). Moreover, procedural differences in data acquisition and their processing to generate three-dimensional models are presented. Models built using a point cloud were created from data collected in the Afrasiyab museum in Samarkand (Uzbekistan) during “The 1st Scientiﬁc Expedition of the Lublin University of Technology to Central Asia” in 2017. Photos for creating 3D models in SfM technology were taken during a virtual expedition carried out under the “3D Digital Silk Road” program in 2021. The obtained results show that the quality of the 3D models generated with SfM differs from the models from the technology (3D SLS), but they may be placed in the galleries of the vitrual museum. The obtained models from SfM do not have information about their size, which means that they are not fully suitable for archiving purposes of cultural heritage, unlike the models from SLS.


Introduction
3D digitisation of museum resources is becoming a more and more frequent practice, but the vast majority is performed by specialised teams representing the scientific community or professional companies offering such services. In recent years, data acquisition technologies have been developed to create three-dimensional models that use data belonging to various types of information. In photogrammetry [1] and Structure from Motion (SfM) [2], a collection of photos is used to build 3D models, which in successive shots of an object cover at least 60% of the surface. Laser scanning or structured-light 3D scanning (3D SLS) provides a cloud of points (x, y coordinates from the object's surface), which ultimately allows us to build its 3D model. In addition to the acquisition of surface point coordinates, colour data are also collected, thanks to which the generated digital model obtains realistic features. In the era of the global pandemic caused by the COVID-19 [3] virus, when excursion and pilgrimage traffic has been halted or significantly restricted, many cultural heritage museum institutions wish to maintain their presence in the tourism market by introducing traditional exhibitions into digital space. The attractiveness of such digital exhibitions, increasingly known as Virtual Museum (VM), will largely depend not only on the uniqueness of the exhibits presented, but also on their digital quality. SfM technology belongs to the so-called low-cost technologies, which may also suggest that the models obtained in this way will not be of sufficiently good quality. The paper presents the results of comparative studies of digital models of the same museum artefacts from the Silk Road area generated by two completely different technologies: SfM and 3D SLS. The developed three-dimensional models based on the point cloud obtained from the scanning were created from data collected in the Afrasiyab museum in Samarkand (Uzbekistan) during "The 1st Scientific Expedition of the Lublin University of Technology to Central Asia" in 2017 [4]. Photos for creating 3D models in SfM technology were taken during a virtual expedition carried out as part of the "3D Digital Silk Road" [5] program in 2021.
The purpose of the article can be summarized as follows: • Comparison of data acquisition procedures for artefacts of material cultural heritage in SfM and 3D SLS technologies. • Generating 3D objects of museum artefacts in SfM and 3D SLS technology. • Assessment of parameters and quality of 3D models obtained in SfM and 3D SLS technologies.

Background Study
In the last two decades, the acquisition of three-dimensional data by laser scanning [6], using structured light [7] or SfM [2,8] has become one of the standard methods of documenting cultural heritage. It makes it possible to analyse the shape, geometry historic artefacts in a safe way [9]. They do not damage the surface or structure of the exhibits, because the activities carried out using the abovementioned methods do not require direct contact with the analyzed object. They allow for the accurate development of digital documentation of the measured object and then, for example, for creating a copy using the 3D printing technique [10].
The interest in scanning techniques is constantly growing and is being developed [11], because digitisation of museum collections allows to preserve exhibits for many decades and to pass on modern scientific achievements to the next generations. Creative involvement in digital 3D models of heritage artefacts can stimulate learning and support new forms of activity using digital models of historic artifacts [12], e.g., it allows disseminating 3D models on the Internet or creating virtual museums. Highly accurate documentation and 3D reconstructions are of fundamental importance for analysis and further interpretations in archeology. In recent years, integrated digital research (ground-based research methods and UAV photogrammetry) has proven its major role in documenting and understanding excavation contexts. This has become possible thanks to the development of specialised devices and the development of appropriate methods for collecting a wide variety of data on site. Several historic sites in the Sepino area of Italy were investigated with these methods and were realised using both range-based and image-based data acquisition methods. The laser scanning data were combined with SfM clouds in the same frame of reference, determined by topographic and GPS measurements [13]. By means of photogrammetry, the area of the Great Plains was examined under field conditions [14], as well as areas of Jordan [15]. The study of the effects of deformation in thermally forced rock masses has aroused growing interest in engineering geologists in the last decade. In this context, digital photogrammetry and infrared thermography and laser scanning have become the two most frequently used analysis techniques in engineering geology applications as they can provide useful information on the geomechanical and thermal conditions of these complex natural systems [16,17]. Photogrammetry and 3D scanning were used in the Pinchango Alto research in Peru [18]. 3D scanning methods were also discussed in the [19] work on the virtual archaeological exhibition. In the study of a unique early Christian carved stone discovered in Scotland, 2D photos were used as the basis for the reconstruction of the 3D model using the SfM method [20]. A FARO Photon Laser Scanner 120/20 system was used to record the geometric data of a complex of historic buildings in Malacca (Malaysia), declared a UNESCO World Heritage Site in 2008 [21]. Scanning with the use of 3D technology was also used to create ethnographic collections [22].
Having digital 3D models allows one to perform a virtual reconstruction of incomplete or damaged artefacts by restoring their original shapes or decorations along with the functions they performed. An example is the reconstruction of a Roman cornice from the Castulo archaeological site (located in Spain) presented in [23]. Virtual 3D models were created on the basis of a series of photos in the paid Agisoft Metashape program, and digital reconstruction using the free Blender software. The reconstructed models were then used to recreate the cavities by 3D printing. Thanks to digital reconstruction, exhibitions in virtual museums gain a new format. Examples of virtual museums created with the use of 3D models obtained in the process of digitisation of objects are the Archaeological Museum in Zagreb [24] and the National Archaeological Museum in Florence [25]. Artefact scans are described in [26], and the obtained models were used to create integrated VR applications.
SfM technology is sometimes dedicated to specific devices. The work [27] describes an example of 3D digitisation of a dress using specialised Autodesk 123D Catch software developed for iPhone and iPad devices. The digital 3D model was generated on cloud servers, after which it was possible to perform surface finishing (Adobe Photoshop) and a 3D model (3ds Max), in which the object was also rendered to transfer it to the Unity engine for presentation purposes.
SfM technology is used in extremely different fields, such as forestry [28] or medicine [29,30]. The SfM method was used to study three contrasting terrain forms at different scales, including: (i) exposed rocky coastal cliffs, (ii) a disturbed complex of moraine dams, and (iii) a bedrock ridge carved in the glacier [31]. Photogrammetric three-dimensional models of objects were made in Colombia, which served as a library of props in landscape visualisation [32]. The mapping technique was used in georeferencing of archaeological aerial photographs [33], and it was also used to study large monuments of the northern river terrace of the Uyuk valley (Russia) and their state of preservation was assessed on the basis of high-resolution optical satellite data [34]. The use of scanning and mapping techniques in the field of geography was used in the study of the water-level fluctuation zone in the Three Gorges Reservoir area in China. An innovative approach to photogrammetry using ships as a device carrier, which was also used for 3D acquisition of landslides, was proposed [35].
Photogrammetry techniques can also contribute to the restoration works of buildings. Study [36] discusses the activities related to the main characteristic elements of the Venetian basilica, which were documented using very high resolution orthophotos. The SfM method was used to integrate the data obtained from the Multi View Stereo and the images generated by a camera placed on an unmanned aerial system (UAS). Tests of generating 3D models based on ground and aerial data acquisition were carried out in the conservation of the Cistercian Staffarda Abbey in Piedmont, a cultural heritage site in Italy. Airborne data acquisition was based on a photogrammetric Remotely Piloted Aircraft System (RPAS) flight, while ground-based research was carried out by laser scanning. Both methods allowed to extract and process various point clouds and generate mesh 3D models of different scales (different resolution, detail content and precision) [37]. In turn, the obtained 3D point cloud was used to study the brick bridge over the Sele River (southern Italy), characterised by unique architecture of historical value, dating from the mid-nineteenth century [38].
Description of available free software for SfM technology and comparative studies of the use of four programs (COLMAP, OpenMVG, Theia and VisualSFM) to create 3D models of several different objects of sizes from 1 to several meters is presented in [2].
In the light of the works discussed, it appears that the application of the SfM method can be found in various fields: cultural heritage, museology, archeology, geography, as well as medicine and even forestry. The cited works also present other technologies of 3D data acquisition of digitised objects. They most often present case studies, and methodological issues are discussed marginally. There is a lack of research that would concern comparative analyses of 3D models obtained by various methods. Only one work was found [39], in which the authors compared the 3D models obtained using four different methods: structured light scanning, triangulation laser scanning, photometric stereo and close-range photogrammetry. This article attempts to answer questions about the efficiency and effectiveness of data acquisition methods and for the creation of 3D models as well as various applications in research and dissemination. Considering the repeatability, time and resource implications, qualitative and quantitative potential, and ease of use, studies of the strengths and weaknesses of these four methods are presented.
In the present work, an attempt is made to fill in the existing gap and present a comparison of the 3D SLS and SfM methods on the examples of digitisation of the same objects representing artefacts of material cultural heritage.

Structured-Light 3D Scanning
Structured light scanners are active devices because they emit light beams from their own source. Scanners of this type project an appropriate pattern of light (a series of fringes with different and, in addition, time-varying widths, a dot matrix or other shape) onto the digitised object. Thanks to this, it is possible to accurately capture the geometric shape of the analysed surface. A light beam with a defined pattern is produced by built-in LCD projectors or other sources. In existing structures, white light is most often used, but also blue or green. These devices also have two or more cameras, as well as detectors that analyse and calculate the distance of surface points in the field of view. Thus the transferred object to the digital world has real dimensions. It should be emphasised, however, that scanners of this type are very sensitive to lighting conditions. All shadows on the real object are mapped onto the generated digital 3D model. For this reason, using them outside can be quite problematic. These scanners typically do not (or even not at all) capture data from black, shiny or transparent surfaces. In such situations the solution used is a matted surface by covering them with a special spray with powder before scanning, which is not allowed when digitising historic artefacts due to their protection. Scanners of this design are characterised by high speed of data acquisition and accuracy of measurements up to several micrometers. These scanners work at short distances (usually 15-40 cm) and, importantly, some structures (e.g., by Artec) can be hand-held, which significantly increases the efficiency of work when using them. There are also known solutions that always have to be mounted on tripods (e.g., RangeVision Neo devices).
Currently, there are many 3D SLS design solutions on the market. Spider and Eva model scanners (Artec, Luksemburg, Luksemburg) are frequently used devices in museum conditions. The fact that these models belong to one manufacturer means that they have common software and the same configuration process. Their main advantage is the comfort of use, because they are light and small, and thus allow a full range of motion during scanning. The advantages also include precise texture and colour reproduction as well as high resolution of the obtained point clouds. This allows for precise examination of objects of various sizes and varied surfaces. The Artec Eva model is better suited for scanning simple geometries, while the Artec Spider model for objects with a complex structure and intricate patterns. It is important that they do not require the use of positioning markers while working, which makes them ideal for scanning museum artefacts. There is also no need to calibrate them before each scanning process, which significantly simplifies and speeds up the work. The specifications of both scanners are presented in Table 1.
These scanners are an effective solution for safe and non-contact digitisation of museum collections. The light with which the measurements are made is neutral for them, so they can also be used to scan very delicate, old and valuable objects. Of course, there are other solutions for devices of this class. Study [40] presents data of the devices compared and parameters of the 3D models obtained.

Structure from Motion
The SfM method, belonging to the passive data acquisition technology, allows to create digital 3D models based on many two-dimensional images (photos). To generate a three-dimensional model, one needs a series of images of an area or object with a large overlap (about 80%), taken at different angles and at different distances, Figure 1 [41]. An average quality camera is sufficient to take pictures, and now even a camera built into a smartphone, making this method a low-cost solution. The smartphone is considered a device of common use, because its price in relation to the many different possibilities it offers to each owner is relatively low. GB RAM, NVIDIA GeForce 400 series * The data come from the manufacturer, but the actual values do not differ from those given, which has been confirmed by our many years of use of this equipment.
These scanners are an effective solution for safe and non-contact digitisation of museum collections. The light with which the measurements are made is neutral for them, so they can also be used to scan very delicate, old and valuable objects. Of course, there are other solutions for devices of this class. Study [40] presents data of the devices compared and parameters of the 3D models obtained.

Structure from Motion
The SfM method, belonging to the passive data acquisition technology, allows to create digital 3D models based on many two-dimensional images (photos). To generate a three-dimensional model, one needs a series of images of an area or object with a large overlap (about 80%), taken at different angles and at different distances, Figure 1 [41]. An average quality camera is sufficient to take pictures, and now even a camera built into a smartphone, making this method a low-cost solution. The smartphone is considered a device of common use, because its price in relation to the many different possibilities it offers to each owner is relatively low. In the SfM method, a series of photos is a set of data that is imported into an appropriate computer program dedicated to this method. This software allows to generate 3D models and textures. Today, there are many programs available, both free and opensource, such as Meshroom [42,43], Colmap [44], VisualSFM [45], and commercial: Agisoft PhotoScan, Capturing Reality RealityCapture [2].
The general process of incremental SfM operations is shown in Figure 2 [44]. It can be broken down into two main modules: correspondence search and incremental reconstruction. The first module aims to search for complete and diffuse matches specific to two images. It has three sub-steps: feature extraction, feature matching, and geometric verification. The second module aims to estimate the alignment of images and three-dimensional scene points. It is possible thanks to the following steps: initialisation (selection of the best pair of images), image registration (for orientation), triangulation (calculation of In the SfM method, a series of photos is a set of data that is imported into an appropriate computer program dedicated to this method. This software allows to generate 3D models and textures. Today, there are many programs available, both free and opensource, such as Meshroom [42,43], Colmap [44], VisualSFM [45], and commercial: Agisoft PhotoScan, Capturing Reality RealityCapture [2]. The general process of incremental SfM operations is shown in Figure 2 [44]. It can be broken down into two main modules: correspondence search and incremental reconstruction. The first module aims to search for complete and diffuse matches specific to two images. It has three sub-steps: feature extraction, feature matching, and geometric verification. The second module aims to estimate the alignment of images and threedimensional scene points. It is possible thanks to the following steps: initialisation (selection of the best pair of images), image registration (for orientation), triangulation (calculation of 3D points), adjustment of the beam (local and global improvement) and removal of outliers.
Appl. Sci. 2021, 11, x FOR PEER REVIEW 6 of 21 3D points), adjustment of the beam (local and global improvement) and removal of outliers.

Description of the Objects of the Experiment
The Afrasiyab museum has exhibits from the city's excavation site. A trading city on the Silk Road, Samarkand was known from the 5th century BC, and was destroyed in 1220 by the invasion of Genghis Khan [46]. Currently, excavation sites covering an area of nearly 200 hectares are located within the administrative area of Samarkand (Uzbekistan). Selected exhibits from this museum have been described and presented using VR exposure [47]. Two very different objects were selected for the comparative analysis of digital three-dimensional models. The first object is a small glazed jug from the turn of the 11th-12th centuries [48]. The shape of the jug is typical of this period and region of origin, it is only 14.1 cm high and 8.9 cm in diameter. A characteristic feature of the jug is a long narrow funnel and a handle placed on the opposite side, of which, in this example, only the upper part of Figure 3a has been preserved. The second object is a reconstructed pottery kiln, 276 cm high, 219 cm wide and 110 cm deep. This object stands against the wall of the exhibition hall and is only accessible from the front, Figure 3b. To make its interior visible, a longitudinal section of the entire facility was made, and for exhibition purposes, jugs of various types and sizes were hung in several rows on the furnace wall, and several bowls and plates were placed inside.

3D SLS Scanning and Postprocessing of the Jug and the Oven
3D scanning was performed in situ. Two handheld 3D SLSs were used for scanning: Artec Spider for digitising the jug and Artec Eva for scanning the furnace, beside a laptop with a 4-core processor and 16 GB of operating memory, Figure 4. Thanks to this, trouble-

Description of the Objects of the Experiment
The Afrasiyab museum has exhibits from the city's excavation site. A trading city on the Silk Road, Samarkand was known from the 5th century BC, and was destroyed in 1220 by the invasion of Genghis Khan [46]. Currently, excavation sites covering an area of nearly 200 hectares are located within the administrative area of Samarkand (Uzbekistan). Selected exhibits from this museum have been described and presented using VR exposure [47]. Two very different objects were selected for the comparative analysis of digital three-dimensional models. The first object is a small glazed jug from the turn of the 11th-12th centuries [48]. The shape of the jug is typical of this period and region of origin, it is only 14.1 cm high and 8.9 cm in diameter. A characteristic feature of the jug is a long narrow funnel and a handle placed on the opposite side, of which, in this example, only the upper part of Figure 3a has been preserved. The second object is a reconstructed pottery kiln, 276 cm high, 219 cm wide and 110 cm deep. This object stands against the wall of the exhibition hall and is only accessible from the front, Figure 3b. To make its interior visible, a longitudinal section of the entire facility was made, and for exhibition purposes, jugs of various types and sizes were hung in several rows on the furnace wall, and several bowls and plates were placed inside.
Appl. Sci. 2021, 11, x FOR PEER REVIEW 6 of 21 3D points), adjustment of the beam (local and global improvement) and removal of outliers.

Description of the Objects of the Experiment
The Afrasiyab museum has exhibits from the city's excavation site. A trading city on the Silk Road, Samarkand was known from the 5th century BC, and was destroyed in 1220 by the invasion of Genghis Khan [46]. Currently, excavation sites covering an area of nearly 200 hectares are located within the administrative area of Samarkand (Uzbekistan). Selected exhibits from this museum have been described and presented using VR exposure [47]. Two very different objects were selected for the comparative analysis of digital three-dimensional models. The first object is a small glazed jug from the turn of the 11th-12th centuries [48]. The shape of the jug is typical of this period and region of origin, it is only 14.1 cm high and 8.9 cm in diameter. A characteristic feature of the jug is a long narrow funnel and a handle placed on the opposite side, of which, in this example, only the upper part of Figure 3a has been preserved. The second object is a reconstructed pottery kiln, 276 cm high, 219 cm wide and 110 cm deep. This object stands against the wall of the exhibition hall and is only accessible from the front, Figure 3b. To make its interior visible, a longitudinal section of the entire facility was made, and for exhibition purposes, jugs of various types and sizes were hung in several rows on the furnace wall, and several bowls and plates were placed inside.

3D SLS Scanning and Postprocessing of the Jug and the Oven
3D scanning was performed in situ. Two handheld 3D SLSs were used for scanning: Artec Spider for digitising the jug and Artec Eva for scanning the furnace, beside a laptop with a 4-core processor and 16 GB of operating memory, Figure 4. Thanks to this, trouble-

3D SLS Scanning and Postprocessing of the Jug and the Oven
3D scanning was performed in situ. Two handheld 3D SLSs were used for scanning: Artec Spider for digitising the jug and Artec Eva for scanning the furnace, beside a laptop with a 4-core processor and 16 GB of operating memory, Figure 4. Thanks to this, troublefree and failure-free operation of scanners and quick processing of downloaded data was ensured. The dedicated software for Artec Studio scanners, version 12 Professional, was responsible for all activities related to data acquisition. The process of scanning the furnace, due to its large size and the complicated shapes of the vessels there, was significantly more difficult.
Appl. Sci. 2021, 11, x FOR PEER REVIEW 7 of 21 free and failure-free operation of scanners and quick processing of downloaded data was ensured. The dedicated software for Artec Studio scanners, version 12 Professional, was responsible for all activities related to data acquisition. The process of scanning the furnace, due to its large size and the complicated shapes of the vessels there, was significantly more difficult. Artec Studio software version 15 Professional and a computer equipped with an Intel Core i7 (3.4 GHz) processor, 64 GB RAM and an NVIDIA GeForce GTX 1080 graphics card with 8 GB internal memory were used to process the data obtained in the process of scanning the jug and stove. The stages of data processing in the form of 3D SLS point clouds on the example of a jug are shown in Figure 5. The final result of the post-processing is a mesh model of the jug and stove with the texture applied, which are exported to files in the .obj format. This format stores data about the spatial model, ie geometry, as well as information about its colour and texture (which is impossible when saving to the .stl format). The texture has been exported to a

Comparison of Data Acquisition Methods and Creating 3D Models
Acquiring data about a three-dimensional object using methods with completely different operating principles means that the user/museologist who would like to use them in practice must properly understand what is available and how it can be processed. Table  2 presents the main features and properties describing the process of data acquisition and processing to obtain digital 3D models of objects using Structured-light 3D Scanning (3D SLS) and Structure from Motion (SfM).

Comparison of Data Acquisition Methods and Creating 3D Models
Acquiring data about a three-dimensional object using methods with completely different operating principles means that the user/museologist who would like to use them in practice must properly understand what is available and how it can be processed. Table 2 presents the main features and properties describing the process of data acquisition and processing to obtain digital 3D models of objects using Structured-light 3D Scanning (3D SLS) and Structure from Motion (SfM).

Results
The obtained results are divided into digitised objects (jug, oven), showing the visual effects of the generated 3D models, after using the 3D SLS and SfM methods, before and after their processing, and the tables present detailed parameter values describing mesh models and textures. When scanning the jug (Artec Spider), three scans were made at different positions of the object on a manually rotated table covered with a special texture ensuring proper positioning of subsequent points of the surface taken from the object (Figure 4a). The resulting files containing all point clouds and object texture information were 1.12 GB in size. Information on individual scans is presented in Table 3.

SfM and Postprocessing
The procedure shown in Figure 6 for creating a 3D model of the jug by the SfM method was used in two variants.
Option 1-use of original photos, without digital processing, see Figure 8.

. SfM and Postprocessing
The procedure shown in Figure 6 for creating a 3D model of the jug by the SfM method was used in two variants.
Option 1-use of original photos, without digital processing, see Figure 8.

SfM and Postprocessing
The procedure shown in Figure 6 for creating a 3D model of the jug by the SfM method was used in two variants.
Option 1-use of original photos, without digital processing, see Figure 8.  Option 2-using photos after processing, Figure 10. The processing of the obtained photos consisted of cropping them and correcting the contrast and brightness in order to obtain objects with similar colours. Framing was carried out in such a way that the jug was located.
In this case, after loading 49 photos into Meshroom, only eight of them were rejected. Thus, the process of creating a 3D model was carried out using 41 photos. The obtained Figure 9. The appearance of a digital model of a jug with SfM: (a,b) without texture-side one and two, (c,d) with texture-side one and two. Option 2-using photos after processing, Figure 10.
Option 2-using photos after processing, Figure 10. The processing of the obtained photos consisted of cropping them and correcting the contrast and brightness in order to obtain objects with similar colours. Framing was carried out in such a way that the jug was located.
In this case, after loading 49 photos into Meshroom, only eight of them were rejected. Thus, the process of creating a 3D model was carried out using 41 photos. The obtained mesh model is shown in Figure 11. It is not difficult to notice that the obtained threedimensional mesh model of the jug was significantly improved, all sides of the object were correctly recreated. Only some surface irregularities appeared on the spout and the walls of the neck and funnel (as shown by arrows in Figure 11b,d).   The processing of the obtained photos consisted of cropping them and correcting the contrast and brightness in order to obtain objects with similar colours. Framing was carried out in such a way that the jug was located.
In this case, after loading 49 photos into Meshroom, only eight of them were rejected. Thus, the process of creating a 3D model was carried out using 41 photos. The obtained mesh model is shown in Figure 11. It is not difficult to notice that the obtained threedimensional mesh model of the jug was significantly improved, all sides of the object were correctly recreated. Only some surface irregularities appeared on the spout and the walls of the neck and funnel (as shown by arrows in Figure 11b,d). Option 2-using photos after processing, Figure 10. The processing of the obtained photos consisted of cropping them and correcting the contrast and brightness in order to obtain objects with similar colours. Framing was carried out in such a way that the jug was located.
In this case, after loading 49 photos into Meshroom, only eight of them were rejected. Thus, the process of creating a 3D model was carried out using 41 photos. The obtained mesh model is shown in Figure 11. It is not difficult to notice that the obtained threedimensional mesh model of the jug was significantly improved, all sides of the object were correctly recreated. Only some surface irregularities appeared on the spout and the walls of the neck and funnel (as shown by arrows in Figure 11b,d).   The improvement of the roughness of the jug surface was achieved by a smoothing process (Smoth modifier) performed with the use of the free Blender software, Figure 12.

Comparison of SLS and SfM Technologies
Collective parameters of digital 3D models (geometry and texture) of a pitcher made in SLS and SfM technology are presented in Table 4.

Comparison of SLS and SfM Technologies
Collective parameters of digital 3D models (geometry and texture) of a pitcher made in SLS and SfM technology are presented in Table 4.
The analysis of the results in Table 4 and the visualisation from Figure 7 shows that in the case of the 3D model obtained from SLS after the 10-fold mesh reduction and 2-fold reduction of the texture dimension the visual quality of the model was maintained and the total file size decreased by more than eight times. This makes it possible to present such a model on websites. In the case of digital objects from SfM technology, the situation is different. The resulting primary model (with photo processing) has the total size (mesh model and texture) more than twice smaller than the SLS model. The surface smoothing process (with the mesh count unchanged) improved the visual quality of the model, but there was a significant increase in the size of its mesh model (by over 60%). Despite the still inferior visual quality of this model, its total size is approximately five times larger than that of the SLS model. Thus it seems that its suitability for presentation on the web becomes more problematic.

SfM and Postprocessing
The procedure shown in Figure 6 was also used to create a three-dimensional model of the furnace by the SfM method. Out of 31 original photos loaded (without processing), Meshroom, after verification, used all photos for further analysis. The obtained three-dimensional model of the furnace is shown in Figure 15a and its elements in Figure 16a.
While the quality of the obtained model of the furnace itself is quite good, the models of vessels in it are not satisfactory. They are definitely different from the models obtained by the 3D SLS method. For this, the 3D model underwent a surface smoothing process in Blender. After carrying out this operation, the unevenness on the surfaces of the furnace itself (Figure 15b), as well as on the surfaces of the elements inside it, decreased (Figure 16b).  Most of the elements that were placed in the centre of the furnace were very well recreated. The 3D models are of very good quality. However, there is an area (shown by the ellipse in Figure 14) where the three-dimensional models have not been properly formed. The presented case results from the fact that in the scanning process the identification of consecutively collected points in relation to the previously recorded points was lost. Such a situation can be identified in the process of point cloud processing. However, for the purposes of this article, this has not been done to show the visual consequences of this situation.
The optimisation of the 3D model of the furnace consisted in simplifying the mesh and texture: the mesh was reduced ten times and the dimensions of the texture used were reduced four times. The data obtained were recorded in Table 5, the realistic model is shown in Figure 13b. After applying mesh optimisation, no significant qualitative differences were noticed compared to the original model.

SfM and Postprocessing
The procedure shown in Figure 6 was also used to create a three-dimensional model of the furnace by the SfM method. Out of 31 original photos loaded (without processing), Meshroom, after verification, used all photos for further analysis. The obtained threedimensional model of the furnace is shown in Figure 15a and its elements in Figure 16a.
Meshroom, after verification, used all photos for further analysis. The obtained three-dimensional model of the furnace is shown in Figure 15a and its elements in Figure 16a.
While the quality of the obtained model of the furnace itself is quite good, the models of vessels in it are not satisfactory. They are definitely different from the models obtained by the 3D SLS method. For this, the 3D model underwent a surface smoothing process in Blender. After carrying out this operation, the unevenness on the surfaces of the furnace itself (Figure 15b), as well as on the surfaces of the elements inside it, decreased (Figure 16b).

Comparison of SLS and SfM Technologies
The collective parameters of digital 3D models of the furnace made in SLS and SfM technology are presented in Table 5. The results included in Table 5 show that the optimisation of the 3D model obtained from the SLS method, consisting in a 10-fold reduction of the mesh size and 4-fold reduction of the texture dimension, with a virtually invisible visual change of the object, resulted in a reduction of the total file size over 6.5 times. With regard to the digital model from the SfM method, the improvement in object visibility after smoothing resulted in an While the quality of the obtained model of the furnace itself is quite good, the models of vessels in it are not satisfactory. They are definitely different from the models obtained by the 3D SLS method. For this, the 3D model underwent a surface smoothing process in Blender. After carrying out this operation, the unevenness on the surfaces of the furnace itself (Figure 15b), as well as on the surfaces of the elements inside it, decreased (Figure 16b).

Comparison of SLS and SfM Technologies
The collective parameters of digital 3D models of the furnace made in SLS and SfM technology are presented in Table 5.
The results included in Table 5 show that the optimisation of the 3D model obtained from the SLS method, consisting in a 10-fold reduction of the mesh size and 4-fold reduction of the texture dimension, with a virtually invisible visual change of the object, resulted in a reduction of the total file size over 6.5 times. With regard to the digital model from the SfM method, the improvement in object visibility after smoothing resulted in an almost 2-fold increase in the .obj file size. It should be added that the size of this file is almost 3.5 times larger than the SLS file, and the appearance of this model is of lower quality anyway. Tables 6 and 7 present the time-consuming nature of data acquisition and processing when creating digital 3D models of a jug and a stove using the SfM and 3D SLS methods. Table 8 lists the costs of devices and software used in the SfM and 3D SLS methods. Table 6. Time-consuming production of the 3D model of the jug using the SfM and 3D SLS methods.  Table 7. Time-consuming production of 3D models of the furnace using the SfM and 3D SLS methods. The analysis of the results in Table 6 concerning the generation of a 3D model of a small jug shows that the time taken by the SfM method is almost twice as long as that of the 3D SLS methods. If more photos were taken, the time would increase to about 3 times. Knowing that raw photos need to be pre-processed, time can be saved by generating a 3D model from these photos and cropping them can follow straight away. In the case of a large object-a furnace (Table 7), it can be seen that the SfM method is about 15 times less time-consuming than the 3D SLS methods. In the method, scanning a large, complex surface takes a long time, as opposed to taking photos. When photographing the furnace, there was no need to create a shooting station, and moreover, the furnace was positioned against the wall, so only one accessible side was photographed. All this meant that the shooting time was 4 times shorter than that of a small jug. The program generating a 3D model from photos requires approximately the same time to generate the model, regardless of whether the object in the photos is large or small. Initial processing of scans from the 3D SLS method, consisting in separating point clouds from each other, when information about reference points was lost in the scanning process, and their recording as separate post-drafts must be performed manually. This operation is very time-consuming, but allows to keep all the data obtained during the scan.

SfM/Meshroom Program min 3D SLS/Artec Studio Professional 15 Program min
The results from Table 8 show that the costs of professional equipment for the 3D SLS method compared to the purchase of a camera are huge (over 35 times) and many museum institutions will not be able to afford them. However, it should be remembered that acquiring a point cloud of the scanned object ensures the archiving of raw data, which constitute the so-called perpetual archiving of a museum artefact.

Conclusions and Further Work
The article presents a comparison of the results of safe and non-contact digitisation of objects from museum exhibitions using two different methods: the 3d Structural-Light Scanning (3D SLS) and the Structure from Motion (SfM) methods. It has been shown that it is possible to select programs and tools, as well as devices enabling the creation of low-cost 3D mesh models using the SfM method, using free software (Meshroom, Blender) and commonly owned devices and computer equipment (camera, laptop).
Using modern information technologies, it has been shown that it is possible to carry out works when employees of partner units are located in different geographic locations in Lublin (Poland) and Samarkand (Uzbekistan). Each team can focus on activities related to professional preparation, sharing their knowledge at the same time, in order to gain new competences in the future in the field of creating digital copies of real models or tangible cultural heritage. By combining the competences of both teams, a synergy effect occurs, which makes it easier to solve emerging problems.
In the light of the research consisting in the creation of digital 3D models of museum objects using the 3D SLS and SfM methods and a comparative analysis of the obtained results, it became possible to formulate the following conclusions: (1) Scanning with the 3D SLS method with the use of Artec Spider and Artec Eva scanners is perfect for mapping museum objects due to the lack of contact with them (the emitted light is neutral for the scanned objects, thanks to which it is possible to scan very delicate, old and valuable objects). It enables effective in situ data acquisition, which significantly simplifies the digitisation process and the necessary formalities to carry it out. (2) Performing the proper postprocessing of the data obtained in the 3D SLS scanning process allows to obtain a faithful 3D mesh model with the applied texture, which can be exported to a file in .obj format with a size many times smaller than the original data obtained. (3) Optimisation of the 3D model mesh using the 3D SLS method and reducing it by up to 10 times while reducing the texture dimension by a factor of 2 does not result in the loss of good visual quality of these objects. This remark applies to very small objects (a 14 cm high jug and a 270 cm high oven). It should be added that the total size of model and texture files is reduced by about 6 to 8 times. As a result, these models are well suited for placement on museum websites. (4) The low-cost SfM method has an unquestionable advantage (over 35 times), which can be an attractive alternative when creating digital 3D models of museum objects. The results of the comparative studies, however, show some of its shortcomings, which means that the obtained three-dimensional digital models are usually of lower visual quality. In addition, due to the improvement of their quality (e.g., surface smoothing), their size increases significantly and is about 3-5 times larger than the size of model files and texture files from the 3D SLS method after optimisation. This may mean that inserting such large model files on museum websites may discourage potential users due to the long download times. (5) The use of the SfM method to create digital 3D models of objects of medium or small size (e.g., a jug with a height of 14 cm) gives much better results when the process of cropping the photo is carried out so that the object is in the centre of the photo. The amount of noise generated in the background of the photo is reduced.
(6) Although the 3D models generated by the SfM method were obtained from a small number of photos, about 30-50 (photos taken by partners from Uzbekistan), the quality of these models turned out to be quite good. This is especially true of a small jug-an object in its main axisymmetric shape. So attention should be paid to getting much more photos of the subject (from 80 to 140). (7) The time of the SfM method when applied to small objects can be reduced (more than 4 times) with careful photographing, paying attention that the object is well-framed, without unnecessary background of the surroundings. (8) The classic SfM method does not provide for placing markers next to the photographed object, so the obtained digital 3D models do not have information about their dimensions. Thus, these models are not fully suitable for the professional archiving of historical objects, but may be useful for popularising and making available tangible cultural heritage.
The authors see the need to continue the work in terms of: (1) Conducting comparative studies of creating digital 3D models of museum objects using the SfM method with the use of other non-commercial and commercial programs. (2) Development of methods and algorithms for comparing the obtained 3D models, which make it possible to calculate the differences between the shape of digital artefacts obtained from both methods and to change the shape of the surface of smoothed and optimised objects in relation to the basic model obtained by the 3D SLS method. (3) Searching for better methods of post-processing 3D models from SfM to improve their visual quality while reducing their size. (4) Developing a list of good practices for the preparation of a collection of photographs of museum objects for the purposes of the SfM method for museum worker.