Improving School Transition Spaces Microclimate to Make Them Liveable in Warm Climates

: The so-called urban heat islands (UHI) is a thermal phenomenon characterized by higher air temperatures in the urban area than in rural surroundings. Vernacular passive strategies such as courtyards are proved to be useful to generate speciﬁc microclimates, especially in the warmer regions of the Earth. Courtyards increase the porosity of the cities, understanding porosity as building voids. Accordingly, their study will be fundamental in reducing the UHI e ﬀ ect by generating urban cooling microislands. This paper aims to analyze two passive strategies capable of modifying the thermal e ﬀ ect of radiation inside the courtyard of two school buildings: albedo and vegetation. In this regard, two case studies were assessed, both of them located in the city of Seville. Results show that the temperature in these spaces can vary up to 7 ◦ C depending on the albedo, which conﬁrms the importance of detecting an optimal albedo factor. In addition, data showed a signiﬁcant increase in the thermal delta (TD), courtyard versus outdoor temperature, after the installation of a vegetal facade. Accordingly, both strategies will be fundamental in locations a ﬀ ected by climate change, especially considering that they are not only e ﬀ ective cooling strategies but also relatively easy to implement in the building’s refurbishment process.


Introduction
Global average temperatures have increased over the last decades and their effects are worrying for today's population. This rise in average temperatures is speeding up even more in large cities with the so-called urban heat island (UHI) effect influencing the daily life of these cities [1]. This thermal phenomenon implies that, while in rural areas the temperature decreases during the night, in the cities this cooling does not occur, producing an overheating of the urban downtown. UHI is more noticeable in hot periods when materials with high thermal capacity act as urban heat sinks during the night. Furthermore, in addition to the thermal accumulation produced by the materials, the massive construction of the ground in the big cities prevents adequate ventilation that helps to reduce this effect. This singularity, related to urban density, has been confirmed by numerous studies at different latitudes, with a value reaching up to 12 • C between rural and urban areas [2,3]. The main difference between the two areas is the presence of hard materials, which are thermally absorbent compared to the nature that invades the rest of the spaces. Therefore, the increase in the presence of vegetation can help to balance this aspect.
Increasingly prevalent summer heatwaves are detrimental to people's comfort and impair their abilities and health [4]. These heat waves are causing even higher overheating in large cities due and the courtyards, and building data related to the geometry, orientation and solar direct radiation would be previously studied to evaluate the courtyards' thermal tempering potential. Although the results obtained in this study are limited to the geometry of transitional spaces such as courtyards under climatic and radiation conditions defined by a precise location, the proposed method has several advantages: it is simple, fast and can be easily implemented in microclimate assessments of outdoor and semi-outdoor spaces. Furthermore, the main novelty of the study is to determine the influence of building envelope surface materials in these semi-outdoor spaces quantifying their impact as passive strategies through full-scale experiments.

Materials and Methods
A methodological model to determine the influence of the different parameters on the courtyard microclimate was applied ( Figure 1). Firstly, a detailed description of the selected case studies and a climate analysis of their location to determine the more suitable periods for field monitoring campaigns were achieved. Secondly, studies of sunlight conditions and radiation were performed. Afterwards, a field monitoring campaign with the previous and later state, after the application of the experiments, for both case studies was carried out. Additionally, finally, the experiments results were analyzed.
Appl. Sci. 2020, 10, x 3 of 13 direct radiation would be previously studied to evaluate the courtyards' thermal tempering potential.
Although the results obtained in this study are limited to the geometry of transitional spaces such as courtyards under climatic and radiation conditions defined by a precise location, the proposed method has several advantages: it is simple, fast and can be easily implemented in microclimate assessments of outdoor and semi-outdoor spaces. Furthermore, the main novelty of the study is to determine the influence of building envelope surface materials in these semi-outdoor spaces quantifying their impact as passive strategies through full-scale experiments.

Materials and Methods
A methodological model to determine the influence of the different parameters on the courtyard microclimate was applied ( Figure 1). Firstly, a detailed description of the selected case studies and a climate analysis of their location to determine the more suitable periods for field monitoring campaigns were achieved. Secondly, studies of sunlight conditions and radiation were performed. Afterwards, a field monitoring campaign with the previous and later state, after the application of the experiments, for both case studies was carried out. Additionally, finally, the experiments results were analyzed.

Case Studies, Location and Climate Description
In this research, two case studies located in the south of Spain were analyzed, specifically, two free-running school buildings in the city of Seville (Seville, Spain, 37° 22′ 58 "N 5° 58′ 23" W, 16 m. a.s.l.). This city is characterized by a warm climate, with high temperatures in summer. The Spanish building regulation, CTE [22], which categorizes the country's climate zoning, references Seville as a B4 climate zone, which indicates a winter with mild temperatures and very hot summers (the highest summer severity). According to Köppen's classification, the city is located in a Csa category area, characterized by hot summers, with a dry and warm climate [23]. The hottest months of the year are characterized by low rainfall. The courtyards selected as case studies have different geometric characteristics, but share orientation and have been monitored under the same climatic conditions over a minimum period of two weeks. The geometry of the courtyard is a fundamental aspect to take into account in the study in addition to the climatic characteristics defined by the location. Previous studies confirm the importance of the relationship between the height (H) and width (W) of the courtyard, known as the aspect ratio (AR) [24] (Equation (1)). Aspect ratios of both courtyards are

Case Studies, Location and Climate Description
In this research, two case studies located in the south of Spain were analyzed, specifically, two free-running school buildings in the city of Seville (Seville, Spain, 37 • 22 58" N 5 • 58 23" W, 16 m. a.s.l.). This city is characterized by a warm climate, with high temperatures in summer. The Spanish building regulation, CTE [22], which categorizes the country's climate zoning, references Seville as a B4 climate zone, which indicates a winter with mild temperatures and very hot summers (the highest summer severity). According to Köppen's classification, the city is located in a Csa category area, characterized by hot summers, with a dry and warm climate [23]. The hottest months of the year are characterized by low rainfall. The courtyards selected as case studies have different geometric characteristics, but share orientation and have been monitored under the same climatic conditions over a minimum period of two weeks. The geometry of the courtyard is a fundamental aspect to take into account in the study in addition to the climatic characteristics defined by the location. Previous studies confirm the importance of the relationship between the height (H) and width (W) of the courtyard, known as the aspect ratio (AR) [24] (Equation (1)). Aspect ratios of both courtyards are described in Table 1. AR (I  and II)  Both case studies are located in primary schools and used to be considered as secondary areas. Currently, due to the Covid-19 pandemic, not only the importance of classrooms' natural ventilation (to avoid aerosol transmission) has been enhanced but also the importance of using outdoor spaces as teaching spaces has been highlighted.
Case Study 1. The first case study is a public school building located in a district in the north of the city. It has a central courtyard on the upper floors where the study is held. The courtyard is in direct contact with the nearby rooms. All of them are classrooms. The courtyard's pavement is coated with a black waterproofing material ( Figure 2). Both case studies are located in primary schools and used to be considered as secondary areas. Currently, due to the Covid-19 pandemic, not only the importance of classrooms' natural ventilation (to avoid aerosol transmission) has been enhanced but also the importance of using outdoor spaces as teaching spaces has been highlighted.
Case Study 1. The first case study is a public school building located in a district in the north of the city. It has a central courtyard on the upper floors where the study is held. The courtyard is in direct contact with the nearby rooms. All of them are classrooms. The courtyard's pavement is coated with a black waterproofing material ( Figure 2).  The following table summarizes the main climatic and geometric characteristics of the case studies analyzed in this study (Table 1). A representation of the geometry of the courtyards is shown in Figure 4 to better compare their proportions. Case Study 2. The second case study is a school building located in the eastern part of the city, recently refurbished. The building includes a central courtyard with square proportions (Figure 3). Both case studies are located in primary schools and used to be considered as secondary areas. Currently, due to the Covid-19 pandemic, not only the importance of classrooms' natural ventilation (to avoid aerosol transmission) has been enhanced but also the importance of using outdoor spaces as teaching spaces has been highlighted.
Case Study 1. The first case study is a public school building located in a district in the north of the city. It has a central courtyard on the upper floors where the study is held. The courtyard is in direct contact with the nearby rooms. All of them are classrooms. The courtyard's pavement is coated with a black waterproofing material ( Figure 2).  The following table summarizes the main climatic and geometric characteristics of the case studies analyzed in this study (Table 1). A representation of the geometry of the courtyards is shown in Figure 4 to better compare their proportions. The following table summarizes the main climatic and geometric characteristics of the case studies analyzed in this study (Table 1). A representation of the geometry of the courtyards is shown in Figure 4 to better compare their proportions. Appl. Sci. 2020, 10, x 5 of 13

Field Measurement Methodology
Different field monitoring campaigns have been carried out in both case studies when the buildings were unoccupied to avoid the interference of the users' load [25]. The minimum period for each monitoring campaign was two weeks. Temperature measurements were taken simultaneously inside the courtyards and on the roof of the buildings. The field monitoring campaigns have been carried out during the warm season to evaluate the influence of the courtyard's tempering effect related to the UHI effect. Measurements have been made using a PCE-FWS-20 (Table 2) portable weather station located on the roof of the buildings, in an open area without any walls or buildings that could affect the measurement of the outside temperature that surrounds the building. This temperature has been compared with the meteorological data provided by the Spanish Agency of Meteorology (AEMET) [26]. The outdoor temperature data differ a few degrees in both measurements; this is because the AEMET data are measured at the airport of Seville, located in the outskirts of the city, thus, avoiding the UHI effect inside the city.  Table 2) data loggers that have been placed 10 cm apart from the walls, located at different heights to check the temperature stratification inside the courtyard. The data loggers have been protected from direct sun radiation by applying a ventilated shield made with insulation material, which also protected them from the radiation from the building envelope. In Figures 5 and 6, the data loggers' position is displayed.

Case Study 2
Case Study 1

Field Measurement Methodology
Different field monitoring campaigns have been carried out in both case studies when the buildings were unoccupied to avoid the interference of the users' load [25]. The minimum period for each monitoring campaign was two weeks. Temperature measurements were taken simultaneously inside the courtyards and on the roof of the buildings. The field monitoring campaigns have been carried out during the warm season to evaluate the influence of the courtyard's tempering effect related to the UHI effect. Measurements have been made using a PCE-FWS-20 (Table 2) portable weather station located on the roof of the buildings, in an open area without any walls or buildings that could affect the measurement of the outside temperature that surrounds the building. This temperature has been compared with the meteorological data provided by the Spanish Agency of Meteorology (AEMET) [26]. The outdoor temperature data differ a few degrees in both measurements; this is because the AEMET data are measured at the airport of Seville, located in the outskirts of the city, thus, avoiding the UHI effect inside the city.
±1 m/s 0-180 km/h -Data obtained inside the courtyards have been recorded by TESTO 174 H and TESTO 174 T ( Table 2) data loggers that have been placed 10 cm apart from the walls, located at different heights to check the temperature stratification inside the courtyard. The data loggers have been protected from direct sun radiation by applying a ventilated shield made with insulation material, which also protected them from the radiation from the building envelope. In Figures 5 and 6, the data loggers' position is displayed. Appl. Sci. 2020, 10, x 6 of 13

Solar Study and Site Radiation
A solar study of both case studies was carried out to detect the optimum facades of the courtyard to adequately plan the field monitoring campaigns (Figure 7). Additionally, the solar radiation distribution of the planning area was calculated in order to evaluate the potential efficiency of any intervention in pavements and facades. Autodesk Revit software [27] that belongs to the BIM environment was used to determine solar radiation distribution

Solar Study and Site Radiation
A solar study of both case studies was carried out to detect the optimum facades of the courtyard to adequately plan the field monitoring campaigns (Figure 7). Additionally, the solar radiation distribution of the planning area was calculated in order to evaluate the potential efficiency of any intervention in pavements and facades. Autodesk Revit software [27] that belongs to the BIM environment was used to determine solar radiation distribution

Solar Study and Site Radiation
A solar study of both case studies was carried out to detect the optimum facades of the courtyard to adequately plan the field monitoring campaigns (Figure 7).

Solar Study and Site Radiation
A solar study of both case studies was carried out to detect the optimum facades of the courtyard to adequately plan the field monitoring campaigns (Figure 7). Additionally, the solar radiation distribution of the planning area was calculated in order to evaluate the potential efficiency of any intervention in pavements and facades. Autodesk Revit software [27] that belongs to the BIM environment was used to determine solar radiation distribution Additionally, the solar radiation distribution of the planning area was calculated in order to evaluate the potential efficiency of any intervention in pavements and facades. Autodesk Revit software [27] that belongs to the BIM environment was used to determine solar radiation distribution during the hottest day of each monitoring campaign. Figure 8 displays the distribution of the total accumulated insolation in case study 1 during one monitoring week, from 9th September to 16th September. In parallel, Figure 9 exposes the distribution in case study 2, from 24th September to 1st October. The maximum and minimum cumulative insolation values for both case studies are shown in Table 3. These values represent the radiation accumulated by the courtyard facades depending on their orientation. Note that in the present research, the solar radiation study was limited to the courtyard unit inside the buildings.
Appl. Sci. 2020, 10, x 7 of 13 during the hottest day of each monitoring campaign. Figure 8 displays the distribution of the total accumulated insolation in case study 1 during one monitoring week, from 9th September to 16th September. In parallel, Figure 9 exposes the distribution in case study 2, from 24th September to 1st October. The maximum and minimum cumulative insolation values for both case studies are shown in Table 3. These values represent the radiation accumulated by the courtyard facades depending on their orientation. Note that in the present research, the solar radiation study was limited to the courtyard unit inside the buildings.   The results of the analysis, in terms of accumulated energy of a surface (kWh/m 2 ), include direct radiation, diffuse radiation, radiation reflected from the ground, shading of surrounding objects, the portion of the sky "visible" by the surface and the angle of incidence between the sun and the face being analyzed [27]. As observed in Table 3, the accumulated solar radiation data for the two case studies analyzed revealed similar maximum and minimum values. This is explained by the similarity in orientation and AR values of both courtyards, despite corresponding to different sizes.

Experiments
As part of the research, the materials of the courtyards' envelope, facades and pavement were changed during the field monitoring campaigns: in case study 1, a change in the albedo of the pavement, with a specific color modification (Experiment 1) and in case study 2, the incorporation of vegetation inside the courtyard consisting of the installation of a vegetal façade (Experiment 2). during the hottest day of each monitoring campaign. Figure 8 displays the distribution of the total accumulated insolation in case study 1 during one monitoring week, from 9th September to 16th September. In parallel, Figure 9 exposes the distribution in case study 2, from 24th September to 1st October. The maximum and minimum cumulative insolation values for both case studies are shown in Table 3. These values represent the radiation accumulated by the courtyard facades depending on their orientation. Note that in the present research, the solar radiation study was limited to the courtyard unit inside the buildings.   The results of the analysis, in terms of accumulated energy of a surface (kWh/m 2 ), include direct radiation, diffuse radiation, radiation reflected from the ground, shading of surrounding objects, the portion of the sky "visible" by the surface and the angle of incidence between the sun and the face being analyzed [27]. As observed in Table 3, the accumulated solar radiation data for the two case studies analyzed revealed similar maximum and minimum values. This is explained by the similarity in orientation and AR values of both courtyards, despite corresponding to different sizes.

Experiments
As part of the research, the materials of the courtyards' envelope, facades and pavement were changed during the field monitoring campaigns: in case study 1, a change in the albedo of the pavement, with a specific color modification (Experiment 1) and in case study 2, the incorporation of vegetation inside the courtyard consisting of the installation of a vegetal façade (Experiment 2).  The results of the analysis, in terms of accumulated energy of a surface (kWh/m 2 ), include direct radiation, diffuse radiation, radiation reflected from the ground, shading of surrounding objects, the portion of the sky "visible" by the surface and the angle of incidence between the sun and the face being analyzed [27]. As observed in Table 3, the accumulated solar radiation data for the two case studies analyzed revealed similar maximum and minimum values. This is explained by the similarity in orientation and AR values of both courtyards, despite corresponding to different sizes.

Experiments
As part of the research, the materials of the courtyards' envelope, facades and pavement were changed during the field monitoring campaigns: in case study 1, a change in the albedo of the pavement, with a specific color modification (Experiment 1) and in case study 2, the incorporation of vegetation inside the courtyard consisting of the installation of a vegetal façade (Experiment 2). Experiment 1. Taking into account previous research [16], in which a study was conducted to see the effects on the microclimate of the albedo in a courtyard, the pavement was covered with two sheets, one white (albedo 0.91) and one black (albedo 0.37). This showed the influence of surface color on indoor and outdoor thermal comfort in public and urban spaces, such as courtyards. Based on this methodology, a similar experiment was carried out in case study 1. The main goal was to study the impact of the albedo on the courtyard microclimate in a warm climate area such as Seville. Due to the current condition of the courtyard pavement (a black waterproofing membrane), another sheet with a higher reflection coefficient was used to study its impact, and to analyze its possible use as a cooling strategy, thus improving the courtyard thermodynamic performance and the comfort of the surrounding classrooms.
To carry out this experiment, air and surface temperature data loggers and a thermal imaging infrared camera were used. The sheet used in the experiment was a 2.00 m × 7.50 m waterproof polymer roofing SIKA ® (SIKA, Baar, Switzerland) membrane ( Figure 10). Based on the solar study, this sheet was placed in the area that receives the highest direct solar radiation during the students' time at the school (from 9:00 a.m. to 5:00 p.m.). The sheet used is Sarnafil TS 77-18 (SIKA, Baar, Switzerland) (waterproof membrane for roofing purposes), it has a CIGS (Copper Indium Gallium Selenide) reflectance of 95%, a solar reflectance of 0.90, an initial emittance of 0.85 and a solar reflectance index of 112. A TESTO 885 thermal camera (TESTO, Lenzkirch, Germany) and a TESTO 435 surface temperature sensor (TESTO, Lenzkirch, Germany) were used to check the surface temperature of the courtyard.
Appl. Sci. 2020, 10, x 8 of 13 Experiment 1. Taking into account previous research [16], in which a study was conducted to see the effects on the microclimate of the albedo in a courtyard, the pavement was covered with two sheets, one white (albedo 0.91) and one black (albedo 0.37). This showed the influence of surface color on indoor and outdoor thermal comfort in public and urban spaces, such as courtyards. Based on this methodology, a similar experiment was carried out in case study 1. The main goal was to study the impact of the albedo on the courtyard microclimate in a warm climate area such as Seville. Due to the current condition of the courtyard pavement (a black waterproofing membrane), another sheet with a higher reflection coefficient was used to study its impact, and to analyze its possible use as a cooling strategy, thus improving the courtyard thermodynamic performance and the comfort of the surrounding classrooms.
To carry out this experiment, air and surface temperature data loggers and a thermal imaging infrared camera were used. The sheet used in the experiment was a 2.00 m × 7.50 m waterproof polymer roofing SIKA ® (SIKA, Baar, Switzerland) membrane ( Figure 10). Based on the solar study, this sheet was placed in the area that receives the highest direct solar radiation during the students' time at the school (from 9:00 a.m. to 5:00 p.m.). The sheet used is Sarnafil TS 77-18 (SIKA, Baar, Switzerland) (waterproof membrane for roofing purposes), it has a CIGS (Copper Indium Gallium Selenide) reflectance of 95%, a solar reflectance of 0.90, an initial emittance of 0.85 and a solar reflectance index of 112. A TESTO 885 thermal camera (TESTO, Lenzkirch, Germany) and a TESTO 435 surface temperature sensor (TESTO, Lenzkirch, Germany) were used to check the surface temperature of the courtyard. Knowing the significance of vegetation as a key strategy in minimizing urban overheating, the second study consists of a modification of one of the facades' surface coating of the courtyard in case study 2. For this purpose, a plant layer with drip irrigation was installed on the facade with the highest direct radiation from the sun as shown below ( Figure 11). The vegetal system used was an optimal passive facade solution consisting of an industrialized and sustainable system that puts together different plants in the same module to be part of the constructive elements in the building´s facade. The vegetal facade was defined by several 100 cm × 100 cm modules (39.4 inches × 39.4 inches). Each module was constituted by several elements that are available in the market and do not require advanced technology: galvanized welded mesh and a plastic cell (replaceable by a metal box) with a substrate for the development of plants. The system includes a galvanized steel structure as a support frame. Knowing the significance of vegetation as a key strategy in minimizing urban overheating, the second study consists of a modification of one of the facades' surface coating of the courtyard in case study 2. For this purpose, a plant layer with drip irrigation was installed on the facade with the highest direct radiation from the sun as shown below (Figure 11). The vegetal system used was an optimal passive facade solution consisting of an industrialized and sustainable system that puts together different plants in the same module to be part of the constructive elements in the building's facade. The vegetal facade was defined by several 100 cm × 100 cm modules (39.4 inches × 39.4 inches). Each module was constituted by several elements that are available in the market and do not require advanced technology: galvanized welded mesh and a plastic cell (replaceable by a metal box) with a substrate for the development of plants. The system includes a galvanized steel structure as a support frame. Appl. Sci. 2020, 10, x 9 of 13 Figure 11. The installation process of the vegetal facade in case study 2.

Results and Discussion
Results of the two UHI mitigating strategies were analyzed below according to the methodology used; first, results corresponding to the field monitoring campaigns are presented, establishing the previous thermal behavior of the selected courtyards. Then, the results after the implementation of the strategies described in the experiments and the potential improvement of the thermal behavior were analyzed.

Analysis of Previous Thermal Behaviour before Strategies Implementation
The thermal tempering performance of the courtyard in case 1 was not particularly relevant (see Figure 12). The microclimatic analysis carried out shows a thermal delta (TD; Equation (2)), up to 4-6 °C for an outdoor temperature range between 25 and 30 °C.
Data loggers placed inside the courtyard show an average TD up to 2 °C. The limited thermal behavior improvement of the courtyard is due to two fundamental aspects: on the one hand, the courtyard geometry, since it has a low AR, which does not allow great stratification and compromises the thermal behavior. On the other hand, the black pavement finishing material, capable of absorbing a great amount of solar radiation, and turning it into overheating. However, the same low AR allows the courtyard to be properly ventilated at night, greatly reducing daytime overheating. The courtyard thermal behavior in case 2 was better than in the previous case study, tempering better the outdoor temperatures, and achieving a TD up to 4 °C at the time of the maximum daily temperature (Figure 13). For a courtyard with an AR lower than 1, this is an adequate TD [3]. In this case, to be able to carry out the subsequent comparison, the results show the values measured on the south-west and south-east facing facades, with hardly any difference between the two. The low depth of the courtyard implies that there is hardly any thermal stratification inside, as in case study 1. In this case, the pavement was white gravel (albedo range close to 0.7), a less absorbent material than in case study 1. Figure 11. The installation process of the vegetal facade in case study 2.

Results and Discussion
Results of the two UHI mitigating strategies were analyzed below according to the methodology used; first, results corresponding to the field monitoring campaigns are presented, establishing the previous thermal behavior of the selected courtyards. Then, the results after the implementation of the strategies described in the experiments and the potential improvement of the thermal behavior were analyzed.

Analysis of Previous Thermal Behaviour before Strategies Implementation
The thermal tempering performance of the courtyard in case 1 was not particularly relevant (see Figure 12). The microclimatic analysis carried out shows a thermal delta (TD; Equation (2)), up to 4-6 • C for an outdoor temperature range between 25 and 30 • C.

Results and Discussion
Results of the two UHI mitigating strategies were analyzed below according to the methodology used; first, results corresponding to the field monitoring campaigns are presented, establishing the previous thermal behavior of the selected courtyards. Then, the results after the implementation of the strategies described in the experiments and the potential improvement of the thermal behavior were analyzed.

Analysis of Previous Thermal Behaviour before Strategies Implementation
The thermal tempering performance of the courtyard in case 1 was not particularly relevant (see Figure 12). The microclimatic analysis carried out shows a thermal delta (TD; Equation (2)), up to 4-6 °C for an outdoor temperature range between 25 and 30 °C.
Data loggers placed inside the courtyard show an average TD up to 2 °C. The limited thermal behavior improvement of the courtyard is due to two fundamental aspects: on the one hand, the courtyard geometry, since it has a low AR, which does not allow great stratification and compromises the thermal behavior. On the other hand, the black pavement finishing material, capable of absorbing a great amount of solar radiation, and turning it into overheating. However, the same low AR allows the courtyard to be properly ventilated at night, greatly reducing daytime overheating. The courtyard thermal behavior in case 2 was better than in the previous case study, tempering better the outdoor temperatures, and achieving a TD up to 4 °C at the time of the maximum daily temperature (Figure 13). For a courtyard with an AR lower than 1, this is an adequate TD [3]. In this case, to be able to carry out the subsequent comparison, the results show the values measured on the south-west and south-east facing facades, with hardly any difference between the two. The low depth of the courtyard implies that there is hardly any thermal stratification inside, as in case study 1. In this case, the pavement was white gravel (albedo range close to 0.7), a less absorbent material than in case study 1.
Data loggers placed inside the courtyard show an average TD up to 2 • C. The limited thermal behavior improvement of the courtyard is due to two fundamental aspects: on the one hand, the courtyard geometry, since it has a low AR, which does not allow great stratification and compromises the thermal behavior. On the other hand, the black pavement finishing material, capable of absorbing a great amount of solar radiation, and turning it into overheating. However, the same low AR allows the courtyard to be properly ventilated at night, greatly reducing daytime overheating.
The courtyard thermal behavior in case 2 was better than in the previous case study, tempering better the outdoor temperatures, and achieving a TD up to 4 • C at the time of the maximum daily temperature (Figure 13). For a courtyard with an AR lower than 1, this is an adequate TD [3]. In this case, to be able to carry out the subsequent comparison, the results show the values measured on the south-west and south-east facing facades, with hardly any difference between the two. The low depth of the courtyard implies that there is hardly any thermal stratification inside, as in case study 1. In this case, the pavement was white gravel (albedo range close to 0.7), a less absorbent material than in case study 1. Appl. Sci. 2020, 10, x 10 of 13 Figure 13. Previous thermal behavior (02-09 October) of case study 2.

Comparison of Thermal Mitigation Strategies Effectiveness
In case study 1, the results show (Figure 14a) how the impact of texture and color of the pavement is fundamental to the thermal behavior of a space such as a courtyard. While the surface temperature of the original black pavement sheet was 70 °C, the surface temperature of the new white sheet was 50 °C, i.e., about 20 °C difference between the surface temperatures of the two materials. A second thermal image was taken when the new sheet was lifted and removed to see the effects that it had on the existing pavement. It can be seen that a lot of heat is stored on the back of the sheet, but it did not reach the temperatures of the current pavement ( Figure 14b). Finally, when the sheet was fully removed and another thermal picture was taken, the thermal footprint was visible while the floor temperature is recovered (Figure 14c). In case study 2, a vegetal facade was implemented in the south-west wall, being the facade that receives more hours of direct solar radiation. When the vegetal facade was installed, it substantially improved the TD regarding the outdoor temperature. While both facades presented no thermal difference before, after the adoption of the vegetation strategy, a difference up to 2 °C at some hours of the day is observed, despite the proximity between the facades ( Figure 15). Moreover, the main objective being the thermal tempering of the microclimate generated by the courtyard is noticeable. The previous TD of 4 °C measured in the first stage (displayed in Figure 16) increased up to 11 °C with the installation of the vegetal façade, comparing a day with similar outdoor temperatures.

Comparison of Thermal Mitigation Strategies Effectiveness
In case study 1, the results show (Figure 14a) how the impact of texture and color of the pavement is fundamental to the thermal behavior of a space such as a courtyard. While the surface temperature of the original black pavement sheet was 70 • C, the surface temperature of the new white sheet was 50 • C, i.e., about 20 • C difference between the surface temperatures of the two materials. A second thermal image was taken when the new sheet was lifted and removed to see the effects that it had on the existing pavement. It can be seen that a lot of heat is stored on the back of the sheet, but it did not reach the temperatures of the current pavement ( Figure 14b). Finally, when the sheet was fully removed and another thermal picture was taken, the thermal footprint was visible while the floor temperature is recovered (Figure 14c).

Comparison of Thermal Mitigation Strategies Effectiveness
In case study 1, the results show (Figure 14a) how the impact of texture and color of the pavement is fundamental to the thermal behavior of a space such as a courtyard. While the surface temperature of the original black pavement sheet was 70 °C, the surface temperature of the new white sheet was 50 °C, i.e., about 20 °C difference between the surface temperatures of the two materials. A second thermal image was taken when the new sheet was lifted and removed to see the effects that it had on the existing pavement. It can be seen that a lot of heat is stored on the back of the sheet, but it did not reach the temperatures of the current pavement ( Figure 14b). Finally, when the sheet was fully removed and another thermal picture was taken, the thermal footprint was visible while the floor temperature is recovered (Figure 14c). In case study 2, a vegetal facade was implemented in the south-west wall, being the facade that receives more hours of direct solar radiation. When the vegetal facade was installed, it substantially improved the TD regarding the outdoor temperature. While both facades presented no thermal difference before, after the adoption of the vegetation strategy, a difference up to 2 °C at some hours of the day is observed, despite the proximity between the facades ( Figure 15). Moreover, the main objective being the thermal tempering of the microclimate generated by the courtyard is noticeable. The previous TD of 4 °C measured in the first stage (displayed in Figure 16) increased up to 11 °C with the installation of the vegetal façade, comparing a day with similar outdoor temperatures. In case study 2, a vegetal facade was implemented in the south-west wall, being the facade that receives more hours of direct solar radiation. When the vegetal facade was installed, it substantially improved the TD regarding the outdoor temperature. While both facades presented no thermal difference before, after the adoption of the vegetation strategy, a difference up to 2 • C at some hours of the day is observed, despite the proximity between the facades ( Figure 15). Moreover, the main objective being the thermal tempering of the microclimate generated by the courtyard is noticeable. The previous TD of 4 • C measured in the first stage (displayed in Figure 16) increased up to 11 • C with the installation of the vegetal façade, comparing a day with similar outdoor temperatures.

Conclusions
In this research, two free-running school buildings with courtyards were analyzed. In both case studies, passive cooling strategies were implemented to thermally temper these spaces by regulating the absorbed solar radiation by pavements and facades of the courtyards. The study aimed to determine the relative efficiency of these strategies to improve specific microclimates of outdoor spaces in buildings and cities.
The results of the performed experiments confirmed that materials, textures and colors of courtyard pavements and facades largely determined their climatic behavior. Previous studies have observed differences between the outdoor and courtyard temperatures up to 15.8 °C when vegetation and water ponds are used in the courtyards [16]. In the present research, the addition of the vegetal facade reached a similar TD, specifically 11 °C. In the case of public buildings that are intended to be thermally refurbished to promote sustainable performances as free-running buildings, this study shows that courtyards offered a great opportunity and are relatively easy to execute, by changing some of the finishing materials. Moreover, improving the microclimate in these types of spaces in schools offers the possibility to use them as teaching spaces and subsequently improves natural ventilation possibilities of the adjacent classrooms, a fundamental issue currently, due to the Covid-19 pandemic.
Specifically, it is possible to lower the surface temperature of a pavement by several tens of degrees by modifying the albedo range. It is also feasible to increase above 10 °C the courtyard TD concerning the outdoor temperature by introducing vegetation into the courtyard using lowmaintenance vegetal facade adapted to the local climate. Furthermore, these strategies can help to reduce the increase of temperatures in cities and improve thermal comfort in adjacent-to-thecourtyard rooms within free-running buildings.
All things considered, the obtained data show a significant transformation of the original microclimate for both case studies, which implies the main contribution of this paper that is to highlight the potential of using an experimental method, based on the evaluation of possible

Conclusions
In this research, two free-running school buildings with courtyards were analyzed. In both case studies, passive cooling strategies were implemented to thermally temper these spaces by regulating the absorbed solar radiation by pavements and facades of the courtyards. The study aimed to determine the relative efficiency of these strategies to improve specific microclimates of outdoor spaces in buildings and cities.
The results of the performed experiments confirmed that materials, textures and colors of courtyard pavements and facades largely determined their climatic behavior. Previous studies have observed differences between the outdoor and courtyard temperatures up to 15.8 °C when vegetation and water ponds are used in the courtyards [16]. In the present research, the addition of the vegetal facade reached a similar TD, specifically 11 °C. In the case of public buildings that are intended to be thermally refurbished to promote sustainable performances as free-running buildings, this study shows that courtyards offered a great opportunity and are relatively easy to execute, by changing some of the finishing materials. Moreover, improving the microclimate in these types of spaces in schools offers the possibility to use them as teaching spaces and subsequently improves natural ventilation possibilities of the adjacent classrooms, a fundamental issue currently, due to the Covid-19 pandemic.
Specifically, it is possible to lower the surface temperature of a pavement by several tens of degrees by modifying the albedo range. It is also feasible to increase above 10 °C the courtyard TD concerning the outdoor temperature by introducing vegetation into the courtyard using lowmaintenance vegetal facade adapted to the local climate. Furthermore, these strategies can help to reduce the increase of temperatures in cities and improve thermal comfort in adjacent-to-thecourtyard rooms within free-running buildings.
All things considered, the obtained data show a significant transformation of the original microclimate for both case studies, which implies the main contribution of this paper that is to highlight the potential of using an experimental method, based on the evaluation of possible

Conclusions
In this research, two free-running school buildings with courtyards were analyzed. In both case studies, passive cooling strategies were implemented to thermally temper these spaces by regulating the absorbed solar radiation by pavements and facades of the courtyards. The study aimed to determine the relative efficiency of these strategies to improve specific microclimates of outdoor spaces in buildings and cities.
The results of the performed experiments confirmed that materials, textures and colors of courtyard pavements and facades largely determined their climatic behavior. Previous studies have observed differences between the outdoor and courtyard temperatures up to 15.8 • C when vegetation and water ponds are used in the courtyards [16]. In the present research, the addition of the vegetal facade reached a similar TD, specifically 11 • C. In the case of public buildings that are intended to be thermally refurbished to promote sustainable performances as free-running buildings, this study shows that courtyards offered a great opportunity and are relatively easy to execute, by changing some of the finishing materials. Moreover, improving the microclimate in these types of spaces in schools offers the possibility to use them as teaching spaces and subsequently improves natural ventilation possibilities of the adjacent classrooms, a fundamental issue currently, due to the Covid-19 pandemic.
Specifically, it is possible to lower the surface temperature of a pavement by several tens of degrees by modifying the albedo range. It is also feasible to increase above 10 • C the courtyard TD concerning the outdoor temperature by introducing vegetation into the courtyard using low-maintenance vegetal facade adapted to the local climate. Furthermore, these strategies can help to reduce the increase of temperatures in cities and improve thermal comfort in adjacent-to-the-courtyard rooms within free-running buildings.
All things considered, the obtained data show a significant transformation of the original microclimate for both case studies, which implies the main contribution of this paper that is to highlight the potential of using an experimental method, based on the evaluation of possible modifications of the coating materials, for a more comprehensive assessment of courtyards' microclimatic performance.