Experimental Study on Co-Firing of Coal and Brewery Wastewater Sludge

: The environmental pollution and high energy consumption caused by the coal-dominated energy structure in China have been the focus of attention for a long time. The co-ﬁring of biomass with coal can save coal resources and realize e ﬀ ective utilization of biomass. In this paper, brewery wastewater sludge (SD) and bituminous coal (BC) were blended for an experimental study which aimed to provide basic experimental data and operational guidance as a reference for practical application in power plants. The co-ﬁring characteristics of sludge and bituminous coal were studied. The results show that the burnout temperature and ignition temperature decrease with an increase in the sludge blending ratio. The Comprehensive Combustion Index (CCI) ﬁrst rises, then decreases, reaching a maximum at about 15%. Compared with the atmosphere with 79% N 2 / 21% O 2 , under the 79% CO 2 / 21% O 2 atmosphere, ignition is delayed and the burnout temperature is higher. Under an O 2 / CO 2 atmosphere, as the O 2 concentration improves, the thermo-gravimetric (TG) curve shifts to the low-temperature region, the burnout temperature drops signiﬁcantly, and the comprehensive combustion characteristics are improved. With an increment of the heating rate, the curve of TG analysis shifts to the high-temperature region and the CCI increases. This study could provide helpful information on practical blending in coal-ﬁred power plants for energy savings and emission reductions.


Introduction
Over the past few years, with the development of the global economy, energy shortages and environmental pollution have become two important issues facing humankind. The development of efficient and clean combustion of fossil energy, the comprehensive utilization of renewable fuels, and the reduction of environmental pollution have become inevitable requirements for sustainable social development. The brewing industry produces a large amount of distillers' waste of about 100 million tons per year [1] in China. Large amounts of sludge are produced in this process; for example, the wastewater treatment after brewing of Wuliangye Group, Sichuan Province, China, produces sludge with a daily output of about 70-80 tons, which greatly pollutes the environment, causes a waste of resources, and increases the burden on brewing enterprises [2,3]. How to reasonably deal with these sludge has become an urgent problem to be solved.
Blended biomass combustion is one of the effective ways for coal-fired power plants to eliminate solid waste from industrial sources, as it can reduce pollutant emissions, improve fuel flexibility and coal performance, and improve conversion efficiency as well [4,5]. In order to investigate the combustion behavior of blended biomass, abundant research has been carried out regarding ignition, burnout, NO X emissions, and so on. In addition, the combustion characteristics of coal and biomass fuels, as well as sludge, have been studied extensively by thermo-analytical techniques such as thermo-gravimetric

Samples
The sample selected for the experiment was the sludge (SD) provided by Wuliangye Winery and the coal type was bituminous coal (BC). In order to study its co-combustion characteristics, during the sample preparation, the sludge and BC were dried and crushed separately, the BC was ground to a particle size of 45-150 µm and the SD was crushed to a particle size of 150-200 µm. Different qualities of coal and sludge were chosen and fully mixed in order to perform co-combustion experiments with different components. They were put into an oven at 105 • C for 24 h for drying pre-treatment [15]. As shown in Table 1, the volatile content of the BC and sludge accounted for 6.78% and 37.72%, respectively. Unlike BC, the main source of the calorific value of sludge is from volatile combustion.

Experimental Methods
A STA449F3 device as a thermo-gravimetric analyzer was adopted for the experiment. The samples were put in an Al 2 O 3 container with a continuous gas flow, and heated from 50 to 950 • C. The co-firing experiment for sludge and coal was carried out in two atmospheres: one was an O 2 /N 2 atmosphere and the other was an O 2 /CO 2 atmosphere. The experimental device is shown in Figure 1.

Experimental Methods
A STA449F3 device as a thermo-gravimetric analyzer was adopted for the experiment. The samples were put in an Al2O3 container with a continuous gas flow, and heated from 50 to 950 °C. The co-firing experiment for sludge and coal was carried out in two atmospheres: one was an O2/N2 atmosphere and the other was an O2/CO2 atmosphere. The experimental device is shown in Figure 1. The co-combustion characteristics of diverse blending rates of brewery wastewater sludge are presented and compared. The effects of the physical properties of N2 and CO2 gas on the TG/DTG curve were explored. The effects of different oxygen concentrations on the ignition, burnout, and Comprehensive Combustion Index (CCI) characteristics of the samples under the O2/CO2 atmosphere were investigated. The CCI indicates the ignition and burnout performance of fuel. The larger the ignition and burnout index, the better the comprehensive combustion behavior. Table 2 shows the experimental cases for this study. There are two main indexes for experimental sample combustion: ignition temperature and burnout temperature, which are important parameters to characterize combustion characteristics. The co-combustion characteristics of diverse blending rates of brewery wastewater sludge are presented and compared. The effects of the physical properties of N 2 and CO 2 gas on the TG/DTG curve were explored. The effects of different oxygen concentrations on the ignition, burnout, and Comprehensive Combustion Index (CCI) characteristics of the samples under the O 2 /CO 2 atmosphere were investigated. The CCI indicates the ignition and burnout performance of fuel. The larger the ignition and burnout index, the better the comprehensive combustion behavior. Table 2 shows the experimental cases for this study. There are two main indexes for experimental sample combustion: ignition temperature and burnout temperature, which are important parameters to characterize combustion characteristics. The ignition and burnout temperature can be confirmed by the thermo-gravimetric curve, such as the DTG weight loss rate method, the DTG curve demarcation point method, the tangent method, and so on [16][17][18][19][20]. The ignition temperature refers to the value at which the sample begins to ignite and the ignition temperature can better characterize the difficulty of igniting the fuel. In this study, the tangent method was adopted to determine the ignition temperature of these samples and the first point of a high weight loss rate on the DTG curve was put to use as a vertical line. The TG curve and vertical line have intersection points. The tangent line of the TG curve is made through the intersection point and the temperature corresponding to the intersection point of the tangent line and the smooth baseline after the fuel is dehydrated and dried is determined to be the ignition temperature, T i . The burnout temperature refers to the point at which TG and DTG no longer undergo significant mass changes. T b is defined by the DTG weight loss rate method: the temperature corresponding to the time when the DTG curve reaches −1 wt%/min at the end of the reaction is defined as the burnout temperature of T b . The CCI reflects the combined combustion of sludge and coal [21] and it contains comprehensive factors of the combustion behavior, including the ignition and burnout temperatures, the maximum DTG reaction rate, and the average DTG reaction rate [22]. A larger CCI indicates that the sample burns more vigorously and rapidly. The following formula [16,[21][22][23] was used: where R and E are the coal reactivity index and activation energy (a detailed explanation can be seen in Reference [16]), (dW/dt) max is the maximum reaction rate of DTG, (dW/dt) mean is the average value of DTG between the ignition temperature and burnout temperature in the blended conditions, and T i and T b are the ignition and burnout temperatures, respectively. Figure 2 shows the DTG and TG curves of sludge and coal in different blending ratios and atmospheres of 21% O 2 /79% N 2 and 21% O 2 /79% CO 2 . The figure indicates that the process of co-firing the blending sludge and coal is divided into three stages: dehydration, precipitation of volatiles, and fixed carbon combustion.

Combustion Characteristics with Different Sludge Blending Ratios and Atmospheres
As shown in Figure 2, for blended samples, there are two obvious peaks on the DTG curve. With the increase of the sludge blending ratio, the ash content of the sludge is higher than that of coal, so the amount of soot after the blended sample is burned out. The peak value of the volatile matter peak increases significantly and the combustion reaction temperature range becomes larger. The fixed carbon peak-to-peak value decreases and the temperature range of the fixed carbon combustion phase becomes smaller. As the proportion of sludge increases, the weight loss rate of the volatile matter of the blended sample increases and the weight loss rate of the fixed carbon decreases. Both the volatile matter and the fixed carbon precipitate and burn in advance.
Appl. Sci. 2020, 10, Compared with the 21% O2/79% N2 atmosphere, the burnout temperature and ignition temperature of the experimental sample under the 21% O2/79% CO2 atmosphere are slightly higher. The burnout temperature addresses the lowest temperature at which the fuel is basically burned out, the main indicator of burnout performance. The lower the burnout temperature, the better the burnout performance. This is because N2 and CO2 have different thermo-physical properties and CO2 has more active chemical properties [24,25]. As the specific heat capacity of CO2 is higher than that of N2, more heat is carried by the airflow, resulting in a lower temperature on the surface of the sludge or coal powder and a decrease in the burning rate. At the same time, the diffusion coefficient of O2 is lower under an O2/CO2 atmosphere and it is more difficult for oxygen to diffuse to the surface and interior of pulverized coal or sludge particles. In addition, when the CO2 concentration is high, the reaction CO2 + HCO + OH competes with H + O2H + O to consume H free radicals, thereby inhibiting the oxidation of CO. In addition, CO2 inhibits H + O2H + O by promoting the reaction H + O2(+M)HO2(+M), because the latter high three-body collision efficiency reduces the reactivity of the system. Therefore, in the 21% O2/79% CO2 atmosphere, the ignition temperature and burnout temperature of the experimental samples are higher and the CCI is slightly reduced. Reference [2] put forward that increasing the proportion of distillers' grains in coal results in a reduced ignition temperature, burnout temperature, and activation energy in the combustion stage and the Comprehensive Combustion Index (CCI) improves with the same tendency as SD and BC blending. Figure 3 shows the Ti, Tb, and CCI of the experimental cases under different atmospheres. The CCI rises first and reaches the maximum when the sludge blending ratio is 15%; that is, 41.13 × 10 −8 Compared with the 21% O 2 /79% N 2 atmosphere, the burnout temperature and ignition temperature of the experimental sample under the 21% O 2 /79% CO 2 atmosphere are slightly higher. The burnout temperature addresses the lowest temperature at which the fuel is basically burned out, the main indicator of burnout performance. The lower the burnout temperature, the better the burnout performance. This is because N 2 and CO 2 have different thermo-physical properties and CO 2 has more active chemical properties [24,25]. As the specific heat capacity of CO 2 is higher than that of N 2 , more heat is carried by the airflow, resulting in a lower temperature on the surface of the sludge or coal powder and a decrease in the burning rate. At the same time, the diffusion coefficient of O 2 is lower under an O 2 /CO 2 atmosphere and it is more difficult for oxygen to diffuse to the surface and interior of pulverized coal or sludge particles. In addition, when the CO 2 concentration is high, the reaction CO 2 + H Appl. Sci. 2020, 10, Compared with the 21% O2/79% N2 atmosphere, the burnout temperature and ignition temperature of the experimental sample under the 21% O2/79% CO2 atmosphere are slightly higher The burnout temperature addresses the lowest temperature at which the fuel is basically burned out the main indicator of burnout performance. The lower the burnout temperature, the better the burnout performance. This is because N2 and CO2 have different thermo-physical properties and CO has more active chemical properties [24,25]. As the specific heat capacity of CO2 is higher than that o N2, more heat is carried by the airflow, resulting in a lower temperature on the surface of the sludge or coal powder and a decrease in the burning rate. At the same time, the diffusion coefficient of O2 i lower under an O2/CO2 atmosphere and it is more difficult for oxygen to diffuse to the surface and interior of pulverized coal or sludge particles. In addition, when the CO2 concentration is high, the reaction CO2 + HCO + OH competes with H + O2H + O to consume H free radicals, thereby inhibiting the oxidation of CO. In addition, CO2 inhibits H + O2H + O by promoting the reaction H + O2(+M)HO2(+M), because the latter high three-body collision efficiency reduces the reactivity o the system. Therefore, in the 21% O2/79% CO2 atmosphere, the ignition temperature and burnou temperature of the experimental samples are higher and the CCI is slightly reduced. Reference [2 put forward that increasing the proportion of distillers' grains in coal results in a reduced ignition temperature, burnout temperature, and activation energy in the combustion stage and the Comprehensive Combustion Index (CCI) improves with the same tendency as SD and BC blending Figure 3 shows the Ti, Tb, and CCI of the experimental cases under different atmospheres. The CCI rises first and reaches the maximum when the sludge blending ratio is 15%; that is, 41.13 × 10 −  Compared with the 21% O2/79% N2 atmosphere, the temperature of the experimental sample under the 21% O2/79% The burnout temperature addresses the lowest temperature at w the main indicator of burnout performance. The lower the b burnout performance. This is because N2 and CO2 have different has more active chemical properties [24,25]. As the specific heat N2, more heat is carried by the airflow, resulting in a lower tem or coal powder and a decrease in the burning rate. At the same t lower under an O2/CO2 atmosphere and it is more difficult for interior of pulverized coal or sludge particles. In addition, whe reaction CO2 + HCO + OH competes with H + O2H + O t inhibiting the oxidation of CO. In addition, CO2 inhibits H + O2 + O2(+M)HO2(+M), because the latter high three-body collisio the system. Therefore, in the 21% O2/79% CO2 atmosphere, th temperature of the experimental samples are higher and the C put forward that increasing the proportion of distillers' grains temperature, burnout temperature, and activation energy Comprehensive Combustion Index (CCI) improves with the sam Figure 3 shows the Ti, Tb, and CCI of the experimental cas CCI rises first and reaches the maximum when the sludge blen  The burnout temperature addresses the lowest temper the main indicator of burnout performance. The lo burnout performance. This is because N2 and CO2 hav has more active chemical properties [24,25]. As the spe N2, more heat is carried by the airflow, resulting in a l or coal powder and a decrease in the burning rate. At lower under an O2/CO2 atmosphere and it is more di interior of pulverized coal or sludge particles. In add reaction CO2 + HCO + OH competes with H + O2 inhibiting the oxidation of CO. In addition, CO2 inhibi + O2(+M)HO2(+M), because the latter high three-bo the system. Therefore, in the 21% O2/79% CO2 atmo temperature of the experimental samples are higher put forward that increasing the proportion of distille temperature, burnout temperature, and activation Comprehensive Combustion Index (CCI) improves w Figure 3 shows the Ti, Tb, and CCI of the experim CCI rises first and reaches the maximum when the sl Compared with the 21% O2/79% N2 atmosphere, the burnout temperature and ignition temperature of the experimental sample under the 21% O2/79% CO2 atmosphere are slightly higher. The burnout temperature addresses the lowest temperature at which the fuel is basically burned out, the main indicator of burnout performance. The lower the burnout temperature, the better the burnout performance. This is because N2 and CO2 have different thermo-physical properties and CO2 has more active chemical properties [24,25]. As the specific heat capacity of CO2 is higher than that of N2, more heat is carried by the airflow, resulting in a lower temperature on the surface of the sludge or coal powder and a decrease in the burning rate. At the same time, the diffusion coefficient of O2 is lower under an O2/CO2 atmosphere and it is more difficult for oxygen to diffuse to the surface and interior of pulverized coal or sludge particles. In addition, when the CO2 concentration is high, the reaction CO2 + HCO + OH competes with H + O2H + O to consume H free radicals, thereby inhibiting the oxidation of CO. In addition, CO2 inhibits H + O2H + O by promoting the reaction H + O2(+M)HO2(+M), because the latter high three-body collision efficiency reduces the reactivity of the system. Therefore, in the 21% O2/79% CO2 atmosphere, the ignition temperature and burnout temperature of the experimental samples are higher and the CCI is slightly reduced. Reference [2] put forward that increasing the proportion of distillers' grains in coal results in a reduced ignition temperature, burnout temperature, and activation energy in the combustion stage and the Comprehensive Combustion Index (CCI) improves with the same tendency as SD and BC blending. Figure 3 shows the Ti, Tb, and CCI of the experimental cases under different atmospheres. The CCI rises first and reaches the maximum when the sludge blending ratio is 15%; that is, 41.13 × 10 −8 HO 2 (+M), because the latter high three-body collision efficiency reduces the reactivity of the system. Therefore, in the 21% O 2 /79% CO 2 atmosphere, the ignition temperature and burnout temperature of the experimental samples are higher and the CCI is slightly reduced. Reference [2] put forward that increasing the proportion of distillers' grains in coal results in a reduced ignition temperature, burnout temperature, and activation energy in the combustion stage and the Comprehensive Combustion Index (CCI) improves with the same tendency as SD and BC blending. Figure 3 shows the T i , T b , and CCI of the experimental cases under different atmospheres. The CCI rises first and reaches the maximum when the sludge blending ratio is 15%; that is, 41.13 × 10 −8 under an air atmosphere and 29.94 × 10 −8 under an oxygen-rich atmosphere. The CCI value then decreases to 24.52 × 10 −8 and 21.87 × 10 −8 when the sludge blending ratio is 50%. This is mainly because a large amount of volatile matter in the sludge in the early stage of combustion pre-ignites and releases heat to promote the combustion of pulverized coal and because the ignition temperature and burnout temperature are reduced, which improves the comprehensive combustion characteristics of the blended fuel. When the sludge blending ratio is large, although the ignition temperature and burnout temperature also decrease, the average combustion rate and maximum combustion rate of the fuel decrease more significantly. At the same time, it can be seen from Table 1 that, compared with the coal containing 44.66% ash, sludge contains 59.86% ash. Therefore, when the sludge blended with fuel increases, the unburned ash of the sludge may be wrapped on the surface of unburned particles, hindering the oxygen diffusing into the particles while restraining the combustion of the inner volatile matter and fixed carbon, making combustion difficult [26].
Appl. Sci. 2020, 10, x 6 of 11 under an air atmosphere and 29.94 × 10 −8 under an oxygen-rich atmosphere. The CCI value then decreases to 24.52 × 10 −8 and 21.87 × 10 −8 when the sludge blending ratio is 50%. This is mainly because a large amount of volatile matter in the sludge in the early stage of combustion pre-ignites and releases heat to promote the combustion of pulverized coal and because the ignition temperature and burnout temperature are reduced, which improves the comprehensive combustion characteristics of the blended fuel. When the sludge blending ratio is large, although the ignition temperature and burnout temperature also decrease, the average combustion rate and maximum combustion rate of the fuel decrease more significantly. At the same time, it can be seen from Table 1 that, compared with the coal containing 44.66% ash, sludge contains 59.86% ash. Therefore, when the sludge blended with fuel increases, the unburned ash of the sludge may be wrapped on the surface of unburned particles, hindering the oxygen diffusing into the particles while restraining the combustion of the inner volatile matter and fixed carbon, making combustion difficult [26].  Figure 4 shows the thermo-gravimetric curves of different oxygen concentrations under a 21% O2/79% CO2 atmosphere. The figure shows that as the oxygen concentration increases, the thermogravimetric curve gradually shifts to the left. This shows that under a high oxygen concentration, the sample burns faster, the reaction temperature range is gradually reduced, and the maximum reaction rate peak gradually increases. Meanwhile, the peak value of the DTG curve increases and the peak corresponding temperature decreases, indicating that the increase of oxygen concentration makes the sample burn at a lower temperature. The combustion peak is reached at a lower point, which is beneficial for combustion. There are two main reasons why the sample burns faster: first, as the oxygen concentration increases, the material comes into contact with oxygen more fully and the combustion is strengthened; second, the increase in oxygen concentration means that the CO2 concentration decreases, which makes the combustion process more efficient. Less heat is taken away and the temperature rises in the furnace, which is more conducive to combustion [3].  Figure 4 shows the thermo-gravimetric curves of different oxygen concentrations under a 21% O 2 /79% CO 2 atmosphere. The figure shows that as the oxygen concentration increases, the thermo-gravimetric curve gradually shifts to the left. This shows that under a high oxygen concentration, the sample burns faster, the reaction temperature range is gradually reduced, and the maximum reaction rate peak gradually increases. Meanwhile, the peak value of the DTG curve increases and the peak corresponding temperature decreases, indicating that the increase of oxygen concentration makes the sample burn at a lower temperature. The combustion peak is reached at a lower point, which is beneficial for combustion. There are two main reasons why the sample burns faster: first, as the oxygen concentration increases, the material comes into contact with oxygen more fully and the combustion is strengthened; second, the increase in oxygen concentration means that the CO 2 concentration decreases, which makes the combustion process more efficient. Less heat is taken away and the temperature rises in the furnace, which is more conducive to combustion [3].   Figure 5 shows that as the oxygen concentration increases from 10% to 40%, the ignition temperature Ti of the mixed fuel decreases from 264.13 to 237.30 °C and the burnout temperature Tb decreases from 737.82 °C to 635.85 °C, resulting in comprehensive combustion; the CCI increases as well. However, the decrease in temperature gradually slows as the oxygen concentration increases. This is mainly because when the pulverized coal particles are filled with high-concentration oxygen, the diffusion control zone of the combustion reaction moves to the reaction power control zone and the oxygen concentration is no longer a key factor affecting the combustion characteristics of the blended fuel [3,16]. Compared with Reference [2], with an increase in O2 concentration from 10% to 40%, the ignition temperature changed over a small range but the burnout temperature declined from 745.8 to 641.4 °C, whereas the activation energy and CCI improved. The brewery wastewater sludge has higher combustion temperature characteristics under the O2/CO2 atmosphere.  Figure 6 shows the thermo-gravimetric curve of the blended samples' combustion at different heating rates. The figure shows that as the heating rate increases, the thermo-gravimetric curve moves to the high temperature zone, whereas at a low heating rate, combustion occurs at a lower  Figure 5 shows that as the oxygen concentration increases from 10% to 40%, the ignition temperature T i of the mixed fuel decreases from 264.13 to 237.30 • C and the burnout temperature T b decreases from 737.82 • C to 635.85 • C, resulting in comprehensive combustion; the CCI increases as well. However, the decrease in temperature gradually slows as the oxygen concentration increases. This is mainly because when the pulverized coal particles are filled with high-concentration oxygen, the diffusion control zone of the combustion reaction moves to the reaction power control zone and the oxygen concentration is no longer a key factor affecting the combustion characteristics of the blended fuel [3,16]. Compared with Reference [2], with an increase in O 2 concentration from 10% to 40%, the ignition temperature changed over a small range but the burnout temperature declined from 745.8 to 641.4 • C, whereas the activation energy and CCI improved. The brewery wastewater sludge has higher combustion temperature characteristics under the O 2 /CO 2 atmosphere.  Figure 5 shows that as the oxygen concentration increases from 10% to 40%, the ignition temperature Ti of the mixed fuel decreases from 264.13 to 237.30 °C and the burnout temperature Tb decreases from 737.82 °C to 635.85 °C, resulting in comprehensive combustion; the CCI increases as well. However, the decrease in temperature gradually slows as the oxygen concentration increases. This is mainly because when the pulverized coal particles are filled with high-concentration oxygen, the diffusion control zone of the combustion reaction moves to the reaction power control zone and the oxygen concentration is no longer a key factor affecting the combustion characteristics of the blended fuel [3,16]. Compared with Reference [2], with an increase in O2 concentration from 10% to 40%, the ignition temperature changed over a small range but the burnout temperature declined from 745.8 to 641.4 °C, whereas the activation energy and CCI improved. The brewery wastewater sludge has higher combustion temperature characteristics under the O2/CO2 atmosphere.  Figure 6 shows the thermo-gravimetric curve of the blended samples' combustion at different heating rates. The figure shows that as the heating rate increases, the thermo-gravimetric curve moves to the high temperature zone, whereas at a low heating rate, combustion occurs at a lower  Figure 6 shows the thermo-gravimetric curve of the blended samples' combustion at different heating rates. The figure shows that as the heating rate increases, the thermo-gravimetric curve moves to the high temperature zone, whereas at a low heating rate, combustion occurs at a lower temperature. As the heating rate increases, the temperature at which the same conversion rate is achieved is higher. This is because of the "thermal hysteresis" phenomenon [27]; that is, the heating rate is too fast to cause the external environment's temperature to be high but there is not enough time to transfer heat from the surface of the fuel particles to the inside, resulting in an excessive temperature difference between the inside and outside of the particles, which is not conducive to the pores with formation and diffusion of oxygen. As the heating rate increases, the internal and external heat transfer of the sample is enhanced at higher temperatures, so the combustion becomes more intense (the DTG weight loss rate value increases).

Tendency of the Heating Rate of Blended Fuels in the O2/N2 Atmosphere
temperature. As the heating rate increases, the temperature at which the same conversion rate is achieved is higher. This is because of the "thermal hysteresis" phenomenon [27]; that is, the heating rate is too fast to cause the external environment's temperature to be high but there is not enough time to transfer heat from the surface of the fuel particles to the inside, resulting in an excessive temperature difference between the inside and outside of the particles, which is not conducive to the pores with formation and diffusion of oxygen. As the heating rate increases, the internal and external heat transfer of the sample is enhanced at higher temperatures, so the combustion becomes more intense (the DTG weight loss rate value increases).  Figure 7 shows the ignition temperature, burnout temperature, and CCIs of blended samples with different heating rates. The figure shows that as the heating rate increases (from 10 to 30 °C/min), the ignition temperature increases (from 208.39 to 253.04 °C) but the burnout temperature increases significantly (from 613.11 to 711.06 °C). This is mainly because the "thermal hysteresis" phenomenon occurs when the heating rate is too fast and the blended fuel cannot be completely burnt in the early stage within a short period of time, so the characteristic temperature increases as the heating rate increases. On the whole, as the heating rate rises, the overall combustion characteristics are improved. Aneta (Reference [6]) conducted TG and DTG experiments on coal, wood biomass, oat and sewage sludge blending at different heating rates. They built three steps (regions) of the studied process to reveal the differences in the initial stage of the process from different amounts of moisture and volatile matter and they proposed a criterion for characterizing the ash fouling tendency. This work provided valuable guidance for our next research.  Figure 7 shows the ignition temperature, burnout temperature, and CCIs of blended samples with different heating rates. The figure shows that as the heating rate increases (from 10 to 30 • C/min), the ignition temperature increases (from 208.39 to 253.04 • C) but the burnout temperature increases significantly (from 613.11 to 711.06 • C). This is mainly because the "thermal hysteresis" phenomenon occurs when the heating rate is too fast and the blended fuel cannot be completely burnt in the early stage within a short period of time, so the characteristic temperature increases as the heating rate increases. On the whole, as the heating rate rises, the overall combustion characteristics are improved. Aneta (Reference [6]) conducted TG and DTG experiments on coal, wood biomass, oat and sewage sludge blending at different heating rates. They built three steps (regions) of the studied process to reveal the differences in the initial stage of the process from different amounts of moisture and volatile matter and they proposed a criterion for characterizing the ash fouling tendency. This work provided valuable guidance for our next research.

Conclusions
In this paper, a TG analysis experimental system and a static combustion experimental platform were used to investigate the influence of the sludge blending ratio, atmosphere, O2 concentration,

Conclusions
In this paper, a TG analysis experimental system and a static combustion experimental platform were used to investigate the influence of the sludge blending ratio, atmosphere, O 2 concentration, heating rate, and combustion temperature on the combustion characteristics of blended fuel. This provides experimental data and a practical reference for the later mixing of sludge in power station boilers and a technical discussion for future O 2 /CO 2 combustion. Several conclusions are drawn as follows: (1) Blending sludge can accelerate the combustion characteristics of single coal. With an increase in the blending ratio, the TG curve shifts to the low-temperature area and the ignition and burnout temperatures of the fuel decrease. Within the 0-50% range of the sludge blending ratio, the burnout temperature only decreases slightly. The ignition temperature drops significantly when the sludge blending ratio is 15%; thereafter, the decline is significantly slower and the CCI reaches the maximum at 15%. It is concluded that the optimal sludge blending ratio is 15% under these experimental conditions. (2) Under O 2 /N 2 with 21%/79% and O 2 /CO 2 with 21%/79% conditions, the change trends of the TG curve of the experimental samples are similar. Compared with the 21% O 2 /79% N 2 conditions, under the 21% O 2 /79% CO 2 atmosphere, ignition is delayed, the burnout temperature is higher, and the CCI is low. In the O 2 /CO 2 conditions, as the O 2 concentration increases, the ignition temperature of the mixed fuel decreases slightly, whereas the burnout temperature decreases significantly. In general, enhancing the oxygen concentration makes the combustion reaction more drastic and improves the CCI. (3) In the O 2 /N 2 atmosphere, with an increment of the heating rate, the TG curve moves to the high-temperature zone, the burnout temperature increases significantly, the combustion rate increases, the combustion reaction becomes more intense, and the CCI is improved.
In the future, the combustion and operation mode of the boiler can be optimized and adjusted based on the normal operating experience of the boiler. This is of great significance for the reform of China's energy structure, allowing full use of the original thermal power units to be made and, at the same time, realizing the utilization of sludge waste resources, which is a good means of saving environmental costs and creating economic benefits.